Simulators: Simulators enable electric guitars to mimic the sound of other instruments such as acoustic guitar, electric bass and sitar. Pick up simulators used on guitars with single-coil pick ups replicate the sound of guitars with humbucker pick ups, or vice versa. A de-fretter is a bass guitar effect that simulates the sound of a fretless bass. The effect uses an envelope-controlled filter and voltage-controlled amplifier to "soften" a note's attack both in volume and timbre.[97]
Regardless of their investment potential or merit compared to Martins, Fenders and Gibsons, the fact remains that clean original Harmony and Kay guitars as well as some of the other interesting student-grade instruments of the 1960s and earlier are quite rare today. Since they were prone to structural problems, many were simply thrown away rather than being repaired. Due to the lack of good repairmen prior to the mid 1970s, attempts to repair such instruments were often as bad or worse than the original problems, further adding to the destruction. Since most of these instruments cost much less than a Martin, Gibson or Fender when new, owners often felt much less of an incentive to take good care of them. Back in the mid 1960s when I was starting out, I saw far more people playing Harmonys, Kays and Danelectos than Martins, Fenders and Gibsons, but for a variety of reasons most of these student instruments have not survived, so that today it is actually a rare occurrence for me to find an original Harmony Sovereign or a good Kay archtop in playable or good cosmetic and structural condition.
How does it sound, you ask? Guitarists generally agree that Line 6 tones are as good, if not better, than any digital sound out there from the likes of Boss and DigiTech. One really cool and intuitive thing is that the small display screen has a color-coded background depending on what type of effect you’re on. It’s a little thing, but such smart thinking from Line 6. Delays are green, Modulations are blue, Distortions are yellow, Filters are purple, and Reverbs are orange. Modulations and delays sound fantastic, and will stack up against a Line 6 DL4 or Boss DD-X box any day. Compressors, overdrives, fuzz, and distortions are usable but less than stellar, which unfortunately is the norm for digital effects. We actually tried using the Line 6 M5 with a solid-state amp, and the dirt effects sound much better going into that than they do into a tube amp (your milage may vary). Remember, this is not meant to replace your entire board. Over time, if distortion is your thing, you can get a dedicated analog distortion stompbox and keep the M5 for the other dozens of effects it does really well. For effects like volume and wah, you’ll be glad to know the M5 has an input for an expression pedal, which you’ll want to invest in if you care to use those types of effects (check out the EX-1 here if you care to stick with Line 6). If you don’t feel like editing patches and want to jump right in, you get plenty of presets to scroll through (the two footswitches let you scroll up and down between patches). Some presets are a little outrageous, but with a little editing you can reel them in and make them more usable. And speaking of scrolling up and down through presets, at first we were disappointed that we had to scroll through all 100+ patches to find the ones we like. Turns out you can make a favorites list of up to 12, and scroll only through those. Again, we’re continually impressed by the little things on the M5.
The pre-amplifier section of a guitar amplifier serves to amplify a weak instrument signal to a level that can drive the power amplifier. It often also contains circuitry to shape the tone of the instrument, including equalization and gain controls. Often multiple cascading gain/clipping stages are employed to generate distortion. Because the first component in a valve amplifier is a valve gain stage, the output level of the preceding elements of the signal chain has a strong influence on the distortion created by that stage. The output level of the guitar's pickups, the setting of the guitar's volume knob, how hard the strings are plucked, and the use of volume-boosting effects pedals can drive this stage harder and create more distortion.

The frets are those thin metal bars running down the neck, which act as note separators, allowing you to play individual notes and chords. Most guitars will feature 22 frets, although those more rock and metal-inclined will sometimes offer 24, allowing you to reach higher notes. As a beginner it shouldn’t really bother you whether you have 21, 22, or 24 frets. It’s only as you grow into the instrument you’ll find what works best for you.
Equalizer or EQ pedals have traditionally been used to boost audio signals for solos. If you want to boost the middle frequencies, the EQ will do the trick and provide a tight tone. Some musicians don’t find boosters and EQ pedals to be necessary in a chain, so make sure you do some research to figure out if this type will really benefit your sound

The irony with guitars is that an original 1950s Gibson, for example, whilst capable of producing the most amazing sounds, and playing like butter - may not stay in tune, or intonate quite as well as a modern day equivalent. Consequently old guitars have very often been 'upgraded', with original parts lost. But this can seriously down-grade their value. Replacing missing parts with original or period-correct ones can very much improve a guitars collectability, saleability and therefore value.
The question here is how high to make the bridge. Well, this is personal choice. Find somewhere were the string doesn’t buzz on any fret from being too low, but low enough that you can play up and down the neck easily. There’s usually a sweet spot where you can just start to detect some buzzing and you can leave it just a tiny bit higher than that. Now do the exact same procedure for the high (thin) E string end of the bridge. Play the guitar a little bit to see if any of the other strings are buzzing. If, say, the A string is still buzzing, then raise up the end of the bridge nearest to that string a little bit ( a small amount of buzzing is often OK as long as it doesn't bother you too much and isn't heard through the amplifier - this a bit of a personal choice thing). OK, that’s step 2 finished. Your guitar should be nice and playable now. However, it may not seem to stay in tune very well. That’s because the intonation might be off.  

With the development of rock, the Tele inspired and sustained yet another genre. Keith Richards of the Rolling Stones has composed many classic riffs on his battered “Micawber” Tele. Iconic are also worn-off green and respectively white Telecasters of the two frontmen of Status Quo, Francis Rossi and Rick Parfitt. Another signature Telecaster player is Andy Summersof The Police. Jimmy Page used a psychedelic-colored 1958 Telecaster, (painted by Page himself, and also known as the “Dragon Telecaster”) on the first Led Zeppelin albums, and also for the lead solo in the 1971 song “Stairway to Heaven“. The guitar had been given to Page by his friend Jeff Beck,[7] who had also been using the Telecaster with The Yardbirds. Bruce Springsteen used a custom Telecaster (with an Esquire neck) off and on throughout his career, both solo and with the E Street Band. David Knopfler, rhythm guitarist from Dire Straitsplayed a sunburst custom Fender Telecaster with white ribboning when with the band.

Taylors are okay as guitars go, but... I've owned three, sold them all in mint condition and lost considerable coin in doing so. I think they belong on this list because they charge hand made prices for MASS PRODUCED guitars. Don't believe me? Take the Taylor that you own and do a search for it on eBay. That's right, at this very moment there are hundreds of guitars just like yours for sale on eBay. And that's only checking this one sales venue! These guitars are worth half of what you paid because the market is saturated with them. Taylor cranks out hundreds of them per day and 100's of thousands per year. If you're shopping and seriously considering a Taylor, you can get comparable quality and far better value elsewhere. Choose carefully and you'll see your investment go up in value. Aside from some special, collectable models of Taylor, you will loose money on this brand.
{"id": "113900398", "categoryId":"site5ABA", "name":"Vintage Vintage 1960s Decca DM1-204 Natural Acoustic Guitar", "pageUrl":"/Used/In-Store-Vintage/Vintage-Vintage-1960s-Decca-DM1-204-Natural-Acoustic-Guitar.gc", "thumbnailUrl":"", "hasFeatures":"0", "isAccessory":"0", "message":"", "value":"179.99", "priceMin":"179.99", "priceMax":"179.99", "msrp":"", "productVisibilityMSRP":"1", "restockPrice":"", "openBoxPrice":"", "clearancePrice":"", "isPlatinum":"0", "priceSavingsMaxPrice":"0.00", "priceSavingsMaxPercent":"0", "inventory":"1", "brand":"In Store Vintage", "reviewStarImageUrl": "", "reviewStarRating":"0.0", "reviewStarRatingInteger":"0", "reviewHowManyReviews":"0", "usedOrNew":"used", "discontinued":"0", "onOrder":"0", "clearance":"0", "canBeSold":"1", "accessoryCategories":"site5LFMID,site5LAAB", "stickerText": "Vintage", "isVintage": "1", "outletonly": "", "checksum":"134135816000", "priceVisibility": "", "itemType": "Vintage"}
In typical pedal effect chains you will most likely be running cable lengths that are much longer than 5.5 meters. The ME-80 allows you to keep your tone pure when running lots of effects. You can run a cable up to 5.5 metres into the input of the ME-80. The multi effects engine processes up to 8 effects in its internal signal chain. Then the ME-80 outputs your guitar signal as a 2,000 Ohm low impedance signal allowing you to run a much longer cable to the amplifier.
Every decision, action, employee hiring, design of new models, etc.-comes from the C.E.O.-Henry J. He dictates every single decision that happens within the company. His power and control over the company is unimaginable. Nothing will change until he leaves or sells the company. First of all the C.E.O. hires every worker- (which is why you wait an eternity to get hired). He doesn't delegate hiring to other departments like other "normal" companies do. That is why you apply, take tons of tests, wait 3 to 5 months (not weeks!), take a drug screen test, if you pass that, then you are finally hired- for a factory job- not a job at the White house! Managers demean workers- most managers don't even have a high school level of education- while most of the workers have some college experience or a 4 yr. degree (including me). Why do the young (20 to 40 yrs. old) educated guys take the job? (1st)- it looks good on the resume, (2nd)- you get to work on guitars, which seems cool at first, until you realize it's a place you do not want to be -most guys leave after a year on average. There is no chance for advancement or a raise. The attitude from Mngt. is intimidation- to rule by fear. They actually get a thrill from firing people, they actually want you to fail, I have never seen anything like it. Everything is about hitting your daily numbers at any cost. Pay raises have been non-existent for years without explanation of why. H.R. is the worst I have ever seen. The women in H.R. dress extremely inappropriate and unprofessional. When you go to H.R. to ask questions, they literally sigh and roll their eyes like you are bothering them -instead of them actually doing their jobs. Nobody knows anything-when you ask for help, you get annoyed responses because they just want to hit their personal number to get out and go home. Managers do as little as possible to not get noticed, but do just enough to keep their jobs- while the workers do all the work to make them look good. Turnover is constant. Stress levels are off the charts. 2012 was my 1st yr. of 2 yrs. working there. We were doing from 650 to 800 guitars a day- (Massman Dr. plant). In comparison the Custom Shop makes about 50 a day. The Memphis Plant- 50 a day. The Montana plant- 50 a day- us =650 to 800 a day! We made the most guitars in 2012 ever -but for the first time nobody received a yearly bonus?!? Which makes no sense -until you figure out everything is about cutting costs-all ordered from the C.E.O. People will skip all their breaks and even lunch to hit their number to get out on time. Countless times we had no lacquer because Mngt. hadn't ordered on time?!? We would have no parts for the guitars (bridges, tuners, etc.)-because they forgot to order on time?!? Yet no one from Mngt. would take accountability for it. One day, 5 people in my dept. (20-30 in the whole plant overall) were fired with no warning (one lady had been there 18 yrs., one guy-8 yrs., etc.)-yet Gibson's attendance policy in their own handbook states you have to be given a oral warning, then a 1st written warning, then a 2nd written warning- yet all the workers were not given any warning. And the reason why is that it had been a slow Christmas season in sales, so they were all let go (ordered by Henry J. -the dictator) to cut payroll-but didn't follow their very own attendance policy-because they don't have to. There is no union, no protection for your job. They tell you you are fired, and to just deal with it, while the powers-that-be don't have to be accountable for anything. It is a dictatorship. A guy I worked there with has been there 20 yrs. And one day he counted up all the workers he remembered being fired or had quit in the 20 yrs. he had been there - it was 350 to 400! If you fail a drug test, you can keep your job?!? So you take 2 weeks off and go to drug rehab- but if you break the attendance policy - you are gone?!?- It's because the company doesn't have to pay you for 2 weeks, and it's something of a tax write off as well (that's what I was told). So basically you can break the law and do drugs- and still have a job. All in the name of saving money. The back break room refrigerator has not been cleaned in 2 yrs! No clock in the main break room for over 5 yrs. and counting! Gibson charged their own employees and their children to attend the company's (workers!) halloween party!?!? Gibson owns Tobias basses-made them 2 yrs. then stopped. Owns Slingerland drums, but hasn't made them in over 12 yrs (pics of them on the website are from late 1990's)! Baldwin pianos (makes on a on-order basis only, and only in Japan, not America anymore). Valley Arts guitars-stopped making them in 2002-12 yrs. ago. Etc,etc.etc! The point being is they buy up all these brand names- and have them on their website as if they are still being sold - but they are not! But they don't say that on their website. The C.E.O. has them to just build value for the Gibson/Epiphone name - to make it more valuable- to sell the company one day at maximum profit. I know this because managers told me this who had first hand knowledge. Guys have been punched in the face during arguments. One guy took a screwdriver and smashed it through the top of a hollow body guitar out of frustration! Arguments are a daily occurrence. My friend would come into work to start his shift, and be so nervous, he would throw up in the bathroom- because of the stress levels and negative atmosphere. Every day literally felt like you were going to prison! I really wanted to make this job work out for me. I am a musician (as are many who work there, many of us play gigs on weekends or nights). My long-term plan was to use my degree, and move up to a corporate position-until I found out what a nightmare the company is. I found out through everyone that I asked that corporate is run the same way! Many might be surprised by this review, because Gibson guitars are really revered by musicians. And outwardly the company has a reputation of the highest quality. But working there was the exact opposite, you would almost rather dig ditches! I have pretty much done it all- I owned my own business, waited tables, worked out in the heat-landscaping, worked in sales, marketing, management, etc. And I have never had such a negative work experience- ever! It affected my health mentally and physically (standing everyday for 10 hrs. or more). And let me tell you for those of you reading this -no job is worth that!
SJ Series: The SJ is Collings’ version of what is commonly called a small Jumbo. Although the 16 inch lower bout is slightly wider than a dreadnought, and the sides almost as deep, the tight curve at the waist creates in a very different sound chamber. SJs, especially examples in maple, typically have a more pronounced midrange response when compared to a dreadnought.
The brilliance of Guitar Rig is the ability to create so many different tones. This is in large part due to the variety of amps that are modeled in the software. You have a choice between Citrus, Ultrasonic, High White, Tweed Delight, Plexi, and Lead 800, among others. I’m sure you can guess what Native Instruments’ clever amp names translate to in the real world.
I think jackson (particularly the USA models) are truly the most versatile of all the high end electric guitars. The build quality is second to none as they are made at the custom shop by very experienced luthiers, the woods used are exotic and tonally superb. The hardware is the best around Floyd rose/ Seymour Duncan's and the action/playability is fantastic. All in all you feel although expensive, you feel like you're getting your monies worth. But the great thing is that they produce an incredible array of sounds which covers all aspects of musical style from the beefed up classic grind of a Gibson, to the stringy percussive violin sounds of a start and everything in between. The USA ones are expensive but I have 2 (an sl 1 and sl 2) and given the enjoyment and reliability they have given me, they owe me nothing.
While the company officially started by importing Spanish guitars, the Ibanez that we know really started in the late '60s when they began copying popular American guitar designs. As expected they got flak for their unofficial "lawsuit" copies, but this ultimately inspired the company to improve on existing designs and develop their own. Soon, virtuosos and big name guitarists like Steve Vai, Joe Satriani and more took notice, propelling the Ibanez brand into world wide renown. Now Ibanez is as big as it gets, with a wide variety of instruments, pedals, and amplifiers under their name. They make it to this list with the high ratings that their amps are receiving, headed by their Tube Screamer Amplifier series, which comes with the circuit of their popular boost/overdrive pedal built into the amplifier section.
Just like in a conventional guitar, an electric guitar also has 6 strings with tuning knobs and frets. However, unlike the hollow body and cavity of an acoustic guitar, a solid body usually forms the lower part of an electric guitar. The long neck of the electric guitar consists of magnetic pickups, parts which produce the magnetic field and which are located just below the metal strings. The magnetic pickups are connected to the amplifier with an internal electrical circuit. The long neck of an electric guitar also consists of knobs for adjusting the elasticity of metal strings.
If you’re looking to get this pedal as a first in your arsenal, then don’t worry at all, you can keep it simple with the offered Reverb dial as it offers high-quality effects which you can tune to your liking. This astonishing “stomp-box” by TC covers guitarist’s needs who possess different ranges of experience, all available at a fantastic startup price.
As successor to the Bogner Triple Giant, the Fish is a pre-amp with a legendary status, due to it’s unique character and it’s 4-channel configuration. Originally introduced in 1990, the unit was limited to 250 pieces, and is a rare find now-a-days. But thankfully, Bogner decided to reintroduce the Fish, featuring a “Country”, “Shark”, “Strato”, and “Brown” channel. Just like the original, this amp can take on just about any style you throw at it!
Martin is a famous America-based company known for is a variety of impressive electric and acoustic guitars. Their guitars are predominantly manufactured in Pennsylvania and Nazareth. The history of Martin guitars dates back to 1833. From then on, Martin has managed to maintain classiness and quality in their guitars to satiate the thirst of pro players in America.
Now, I'm sure that you're all sensibly busying yourselves with making music, so your lives are, frankly, too short to be sifting through more than a half a million words of interviews. Therefore, I'm going to try to digest what I've discovered during this process for the benefit of those less sad than me! I'm not about to dictate which technique is 'best', though, because if reading this many interviews has taught me anything it is that people will always disagree on what constitutes a great sound. Instead I've recorded a number of different audio examples to allow you to judge for yourselves, just as I did, which techniques are likely to make a real difference to your own productions. I've peppered this article with a number of boxes giving details of these files.
What every great guitarist does, with respect to sound, is achieve a very high level of nuanced control over the sound, not by having a computer play his guitar for him. As a keyboard player, I would recommend you first concentrate on playing your synth with lots of use of pedals, velocity-sensitive changes in timbre, and left hand controllers. Then you can experiment with all sorts of synth sounds. This way, you can play as expressively as a gutarist, but without sounding like a bad copy. Instead, you can sound like something different, new, and this is really where synth lead work can shine (and actually add to our musical lexicon).
Great pedal! It is small, but is very sturdy and the design looks great. Each effect sounds great and the controls are easy to use. I would put each effect in this pedal up against any single effects pedal that I currently have and this multi-effect was cheaper than all of those. I play a lot of genres from country, classic rock, and metal and these effects can get you the tones you need for each! I am thoroughly impressed.

Guitar picks are really cheap, maybe $.25 to $.50 each. The best way to know which kind you like best is go to a music store and buy $5.00 worth of picks of different thicknesses, sizes and materials, take them home and try them out over the course of the next several weeks or months as you learn to play. There is no right or wrong answer to this question, its all a matter of personal preference. You'll figure out for yourself which you like best.
Most people think of Roy Orbison as the super-smooth crooner who sang songs like “Crying,” “In Dreams” and “Only the Lonely.” But Orbison was also a wicked guitar player, who ripped out several impressive solos on early Sun Records singles like “Ooby Dooby.” In fact, Sun owner Sam Phillips was more impressed with Orbison’s guitar playing than his singing during the early days of the rocker’s career.
The body of the instrument is a major determinant of the overall sound variety for acoustic guitars. The guitar top, or soundboard, is a finely crafted and engineered element often made of spruce, red cedar, redwood or mahogany. This thin (often 2 or 3 mm thick) piece of wood, strengthened by different types of internal bracing, is considered the most prominent factor in determining the sound quality of a guitar. The majority of the sound is caused by vibration of the guitar top as the energy of the vibrating strings is transferred to it. Different patterns of wood bracing have been used through the years by luthiers (Torres, Hauser, Ramírez, Fleta, and C.F. Martin being among the most influential designers of their times); to not only strengthen the top against collapsing under the tremendous stress exerted by the tensioned strings, but also to affect the resonation of the top. Some contemporary guitar makers have introduced new construction concepts such as "double-top" consisting of two extra-thin wooden plates separated by Nomex, or carbon-fiber reinforced lattice - pattern bracing. The back and sides are made out of a variety of woods such as mahogany, Indian rosewood and highly regarded Brazilian rosewood (Dalbergia nigra). Each one is chosen for its aesthetic effect and structural strength, and such choice can also play a significant role in determining the instrument's timbre. These are also strengthened with internal bracing, and decorated with inlays and purfling.
Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Custom - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Diecast, Gold, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Ivory, Sunburst
For guitarists who must have original-era Strat® sound, look and feel, the Classic Series '60s Stratocaster Lacquer epitomizes the instrument during its second decade, when musicians used it to conjure and create electrifying sounds never before imagined or experienced. With authentic features including a nitrocellulose lacquer finish in classic Fiesta Red, everything about it takes you back to a wildly creative time when rock music came into its own—from surf to psychedelia and more—and players started to discover in earnest just what a phenomenal instrument the Stratocaster really was.
Some large combo amps and large speaker cabinets have ball-bearing-mounted caster wheels to make it easier to move them. All combo amplifiers and speaker cabinets have some types of carry handles, either a folding handle on the top or recessed handles on the sides. There are two types of recessed handles: some equipment has folding, spring-loaded metal handles, with the spring holding the handle flush against the chassis until it is pulled out for use; the second type is handles that are non-moving, and which are flush with the surface of the amp/cab, but with a hollow area behind the handle for the hand to go. In both cases, the handle does not project out beyond the amp/cab, preventing the handle from catching on items during transportation and/or being damaged.
the most with a headphone jack. Any suggestions? I am just a bedroom player who sucks and price is well I say depends what it (the amp) is worthy b/c I am on disability and my neurologist said just quit but at 48 years old it (music) is the only area of life besides my dog and mom that keeps me even and she is in worse shape than me (sorry for the soap box). Is the EVH 5150 III though its' combo is 50 watts but it has the headphone jack. Please anyone help???
Here's my attempt to catalog those songs. Note that these are not necessarily my personal favorites by each artist, although I think all of them are at least pretty good. I tried to stick to at least "acoustic-friendly" songs. They range from incredibly simple to fairly complicated, but nothing is near-impossible. I omitted several popular piano tunes that would be easy to learn on guitar. Also note that many if not most of these are intended to be sung simultaneously for full effect. And finally, yes, the songs are in alphabetical order because I thought of most by scrolling down my iTunes list
Some of the best guitar compositions come from simple experimentation; that's why jam sessions are so great. When you want to have your own personal jam session, using a headphone amp is a fantastic idea. That way, you can keep your genius to yourself until it's ready for its first audience. You'll have the freedom to experiment all you want without having to worry about unwanted ears listening in, and that'll give your new riff even more of an impact when you unveil it on your main amplifier.
I have a Gemtone guitar tube amp that was made in Canada in early 70's I think. This is the only Gemtone I have ever seen and the only information I could find out about it (but not verify) is that it was a sub-company of Regal Instruments. I would love to find some more info about this amp but have nearly given up after several years of searching. Sorry its not really an answer but my hope is to fire up the thread again so someone with more concrete info can chime in.

Wiring the phase switch is fairly simple. Solder 2 wires in the criss-cross manner shown in the diagram. In the guitar cavity, unsolder the 2 bridge pickup leads; solder the phase switch "Out" leads to the exact same spot where the pickup leads were; solder the bridge pickup leads to the "From Pickup" terminals on the phase switch. Mount the switch, close up the guitar and start enjoying the new sound you just created!

There seems to be a lot of confusion about the origins of Palmer guitars. I know a few people have said they are made in America but I cant find anything about that site. However there is a guitar maker and restorer called James Arthur Palmer in Stoke on Trent, England. If you simply google his name then nothing will come up but if you enter J.A.P. guitars it will lead you to his site. Hope this helps.
American Fenders and USA Gibsons are not NOT for beginners! They are for people like myself who have invested 15+ years into developing the skills required to defend a purchase of one. IF you want beginner guitars, go see Mexico Fenders or Epiphone Guitars. Better yet, worry more about your skill and not which brand in on your headstock. I played for 11 years before I upgraded my Epiphone to a Gibson.
To fulfill the diverse requirement of our esteemed clients, we are engaged in offering them a wide range of Electric Spanish Guitar. This offered range of Electric Spanish Guitar is available with us in various shapes and size and can also be modified as per our clients requirement. Our clients highly appreciate our offered Electric Spanish Guitar for its
Until the 1950s, the acoustic, nylon-stringed classical guitar was the only type of guitar favored by classical, or art music composers. In the 1950s a few contemporary classical composers began to use the electric guitar in their compositions. Examples of such works include Luciano Berio's Nones (1954) Karlheinz Stockhausen's Gruppen (1955–57); Donald Erb's String Trio (1966), Morton Feldman's The Possibility of a New Work for Electric Guitar (1966); George Crumb's Songs, Drones, and Refrains of Death (1968); Hans Werner Henze's Versuch über Schweine (1968); Francis Thorne's Sonar Plexus (1968) and Liebesrock (1968–69), Michael Tippett's The Knot Garden (1965–70); Leonard Bernstein's MASS (1971) and Slava! (1977); Louis Andriessen's De Staat (1972–76); Helmut Lachenmann's Fassade, für grosses Orchester (1973, rev. 1987), Valery Gavrilin Anyuta (1982), Steve Reich's Electric Counterpoint (1987), Arvo Pärt's Miserere (1989/92), György Kurtág's Grabstein für Stephan (1989), and countless works composed for the quintet of Ástor Piazzolla. Alfred Schnittke also used electric guitar in several works, like the "Requiem", "Concerto Grosso N°2" and "Symphony N°1".
Despite the numerous different analog devices, it is very rare for them to be able to duplicate all aspects of a Leslie speaker. Thus, Rotary Speaker Simulator are always going to be digital, utilizing modelling algorithms to model the relations between the rotating horns and bass baffle. And how the sound bounce around the cabinet. As Leslie also have an amplifier section, most of these typically have overdrives to simulate that aspect. Some of these pedals can even accept keyboard's input.
A typical modern guitar tube amp has both a preamp stage and a master power amp output stage. The preamp section will be supplied with a set of smaller tubes (frequently 12AX7 or the lower-gain/lower noise 12AU7), and the power amp section has a set of large tubes (EL34, EL84, 6L6, etc.). The preamp controls input gain and typically provides treble, midrange and bass tone controls.
CHEVALET HARDTAIL Pour remplacer les cordes, faites passer les nouvelles cordes à travers les passe-cordes qui se trouvent au dos de la guitare et faites-les ressortir par-dessus les pontets. L'intonation peut être réglée en déplaçant le pontet vers l'avant ou vers l'arrière, en utilisant un tournevis cruciforme (+) pour ajuster la vis de réglage de l'intonation, située à...
These brands consist of guitars that are made up of high quality material including hardware stuffs, wood, etc with interesting features. Well, it not so that only expensive guitars are good for the learners. Music is such a wonderful pleasure that can make any one happy form inside. But all this is possible through excellent music instruments including guitar. Nothing can be powerful in sad situations than music played by guitar. The brands provided below are the most prominent guitars brands at economical prices. So, it is essential to select a perfect guitar which not only make your understand easily but also match to the style and requirements of your lifestyle. Some beginners think to choose a low quality and less expensive brand guitar but it’s all their misunderstanding.

Chorus: Though it can be overused, light distortion works well as a filler for choruses in Christian worship and most other genres.Verse: You won’t typically hear a distorted verse, though at times a two guitar group can make this work. Generally, you’ll want to leave distortion for the higher intensity portions of a song.Bridge: A lot of Christian songs tend to lower intensity during the bridge, which means light distortion becomes a little less usable. Though for bridges that keep the tempo up, it can work pretty well.

As a musician for 50 years and a custom builder for 30 years I definitely believe that wood choice has an effect on the tone and sound characteristics of an electric guitar. In my younger years as a cabinet maker, I was helping install a large church pipe organ (Cassavan I believe). The installer from Montreal and I had some discussions about wood and specifically wood properties best for certain applications. He told me that they used poplar for the spacers between the organ pipes because as a good tone wood, sound did not bleed from one pipe to another which is very important with pipe organs. They are the oldest and I believe the largest pipe organ manufacturer in the world and have done a lot of trial and error in this area according to the installer as to what wood works best. I happen to agree with them and agree that poplar is an excellent tone wood and works very well in guitars. Jackson guitars use poplar in there guitar bodies and is a great sounding tone wood. I use it a lot in my custom guitar because of the nice tone it produces.
If you want to splurge just a bit more and opt for an instrument with a little more stylistic range, the Ibanez Talman guitar vault accessory kit might be right up your alley. It includes a lovely seafoam green Ibanez TM302SFG, 12 high-quality Dunlop Tortex picks, a strap, a gig bag, a Kyser capo, a polishing cloth, and a tuner. This is off the beaten path a bit, but for some players, that’s going to be absolutely perfect.
Consider the use of a power soak. A power soak is a supplemental piece of equipment used in-line to reduce the volume output of an amp while maintaining tone and sustain. The signal moves through the line to the power soak, which absorbs part of the full power of the amp. This adjusted signal is transmitted to the amp, resulting in quieter volumes.[26]

The Jeff Beck Oxblood is available in limited numbers. The first 50 of these historic guitars were aged at Gibson Custom to look like Beck’s original, then signed, numbered and played by Beck himself. The next 100 guitars were prepared with Gibson Custom’s V.O.S. finish, bringing the total run to 150 instruments. Each one also comes with a standard Gibson Custom case.
In 1972, Ovation introduced one of the first production solid-body electric-guitars with active electronics, the Ovation Breadwinner. The model failed to gain widespread popularity, however, and production of the Breadwinner and the Ovation Deacon ceased in 1980. Ovation made several other solid-body models up until the mid 1980s.[28] Since that time the company’s main focus has been acoustic and acoustic-electric guitars.

Acoustic and electric archtops are identical in design with the only difference being the addition of electro-magnetic pickups and pots. Archtops can either be full-bodied or thinline. The full-bodied archtop retains good volume and acoustic resonance when played unplugged though feedback may be an issue when amplified. The thinline body minimizes feedback by sacrificing acoustic volume and resonance.
The Epiphone Thunderbird IV Reverse Bass is Epiphone’s most distinctive bass guitar to date. The Thunderbird features the classic reverse body styling and dual humbuckers just like the Gibson originals! The Thunderbird IV features an alder body and a 34 inch scale bolt-on maple neck with a rosewood fretboard and dot inlays, and warm and phat dual humbucking pickups.
If you are considering a traveler or mini guitar, be sure to read reviews of people who own models that range between $40 - $500, because you will find various reasons to stay away from some of the cheaper models that are under$150.  Some of these guitars that are made that cheaply are not much better than toys in quality, sound and crafstmanship, and at this model and price range, you will get what you pay for.  By investing an extra $100 - $200, you can find some fine travelers and minis that will more than accomplish the job, and in fact, some professionals choose certain travelers and minis over others for playability, quality, performance and recording reasons.
Specs for your guitar include an ash body and carved maple top (rosewood was an option) bound with an abalone border, and a 5-piece maple/rosewood through-body neck. Other features include the bound 22-fret ebony fretboard with brass circle inlays, a matched-finish headstock with abalone border, 3-per-side tuners, two exposed humbuckers, and controls for each pickup. Its ivory finish is probably the most desirable color for this model, but the guitar was also available in a natural finish that highlighted the maple or rosewood carved top.
omg guitar playing isnt just about speed and technically skill. its about style and uniqueness of sound, as shown by tom morello and jack white. most of those metal guitarist, with quite a few exceptions ill admit (tony iommi, john petrucci, randy rhoads & van halen, and joe satriani & steve vai), sound EXACTLY THE SAME. i think you need to expand YOUR musical taste.
wonderful feel of a small town, with caring people and the owner is amazing. He'll of a player too! Just got a gorgeous ESPN strat copy from him, he graciously showed me just how well of a strat it is... by playing it through a fender tweed tube amp. He even sang a little for me as he made my strat sing right along with him. Price was excellent, as are all his prices. See More
Gibson sells guitars under a variety of brand names[5] and builds one of the world's most iconic guitars, the Gibson Les Paul. Many Gibson instruments are highly collectible. Gibson was at the forefront of innovation in acoustic guitars, especially in the big band era of the 1930s; the Gibson Super 400 was widely imitated. In 1952, Gibson introduced its first solid-body electric guitar, the Les Paul, which became its most popular guitar to date— designed by Ted McCarty and Les Paul.

Pickup configuration refers to the number and types of pickups installed on a guitar, and its position on the body. The two most common types of pickups include singlecoil, known for its crisp and punchy sound and the fatter sounding humbucker. For beginners, you'll have to once again look up to artists who play your preferred music genre, to see which pickups they are using to get their sound. In addition to getting the right sound, sonic flexibility is also an important consideration and the general rule is that the more pickups installed, the more sound varieties you can get. The most common configuration is HH, which stand for dual humbuckers, because of their overdrive and distortion friendly sound. The SSS (three single-coils) configuration is also popular, as seen on the Stratocaster, allowing for a more versatile tone options. There are other variations that combine both single coils and humbuckers, such as SSH (two single coils and a humbucker), for an even wider selection of tones.

The classical guitar also became widely used in popular music and rock & roll in the 1960s after guitarist Mason Williams popularized the instrument in his instrumental hit Classical Gas. Guitarist Christopher Parkening is quoted in the book Classical Gas: The Music of Mason Williams as saying that it is the most requested guitar piece besides Malagueña and perhaps the best known instrumental guitar piece today. In the field of New Flamenco, the works and performances of Spanish composer and player Paco de Lucía are known worldwide.

Fender California Coast Series acoustic guitars are already being used across multiple musical genres by top alternative, indie, punk and grunge artists/bands, such as: Culture Abuse, The Regrettes and Dear Boy, as well as singer-songwriter Aaron Lee Tasjan and guitarist Angela Petrilli – accompanying each on their musical journey toward exceptional artistry.
Martin also periodically offers special models. Many of these have a limited production run, or begin as a limited-production guitar that sells well enough to become regularly produced. Many of these special models are designed with, endorsed by, and named after well-known guitarists such as Eric Clapton,Clarence White, Merle Haggard, Stephen Stills, Paul Simon, Arlo Guthrie andJohnny Cash. In 1997, Martin launched its “Women in Music” series, which was followed in 1998 by the Joan Baez Signature guitar, a replica of the 0-45 Baez began her career with.
Three and one half steps down from Drop D. Used by Darkest Hour on the song "Wasteland", Attack Attack!, Baroness (on their first two EPs), The Acacia Strain (on some songs), Dead by April (on some songs) and In Flames (on the song "Transparent" from Reroute to Remain). Chelsea Grin also used this tuning on their album Ashes to Ashes. Also Pantera and Whitechapel recorded Sandblasted Skin in G-g-C-F-A-D, Drop G variation with D standard.
Additionally, Gibson’s president Ted McCarty states that the Gibson Guitar Corporation merely approached Les Paul for the right to imprint the musician’s name on the headstock to increase model sales, and that in 1951, Gibson showed Paul a nearly finished instrument. McCarty also claims that design discussions with Les Paul were limited to the tailpiece and the fitting of a maple cap over the mahogany body for increased density and sustain, which Les Paul had requested reversed. However, according to Gibson Guitar, this reversal would have caused the guitar to become too heavy, and Paul’s request was refused.[12] Another switch: the original Custom was to be all mahogany and the Goldtop was to have the maple cap/mahogany body. Beyond these requests, Les Paul’s contributions to the guitar line bearing his name were stated to be cosmetic. For example, ever the showman, Paul had specified that the guitar be offered in a gold finish, not only for flashiness, but to emphasize the high quality of the Les Paul instrument, as well.[12] The later-issue Les Paul models included flame maple (tiger stripe) and “quilted” maple finishes, again in contrast to the competing Fender line’s range of car-like color finishes. Gibson was notably inconsistent with its wood choices, and some goldtops have had their finish stripped to reveal beautifully figured wood hidden underneath.[citation needed]
Description: Body: Laminated Maple - Flamed - Top Wood: Laminated Maple - Flamed - Neck Wood: Maple - Neck Construction: U-Shape - Nut Width: 43mm - Fingerboard: Ebony - Binding: White - Frets: 22, Jumbo, Medium - Inlay: Pearloid Thumbnail - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 3+3 - Bridge: Rocking Bar - Cutaway: Double - Hardware: 2x Volume Control, 1x Tone Control, 3-Way Switch, Schaller Tuners - Pickups: FilterTron - Pickup Configuration: Dual - String Instrument Finish: Orange Stain
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: fernandes","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"fernandes","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] sub category"}

All Gibson-brand guitars are currently made at three facilities, depending on the type of guitar. Solid body electric guitars such as the Gibson Les Paul and the Gibson SG are made in Nashville, Tennessee. Semi-acoustic guitars such as the Gibson ES Series are made in Memphis, Tennessee. Full acoustic guitars such as the Gibson J Series are made in Bozeman, Montana. The Nashville and Bozeman facilities are off-limits to visitors, but the Memphis facility gives regularly scheduled factory tours.
This is one of the most popular guitar brands bought by the beginner and advanced learners in India. This brand is also one of the top-rated electro-acoustic guitars for beginners. This is the Japanese brand of guitar that is available in acoustic, bass, electric, and classical guitars styles. It flourishes a full-size frigate shape with a laminated select dapper top, and mahogany back and sides. It sports a mahogany neck, with a rosewood fretboard and 20 frets, withal an Ibanez-branded headstock with pretty good closed chrome die-cast tuners. The price of this brand of guitar starts from 13,000 approximately.

This guitar is perfect no matter if you’re a beginner or have been playing for many years. The design is vintage at its best, with a lovely soft V-shaped neck and great colors, namely Surf Green, Daphne Blue and Fiesta Red. This guitar has a very traditional look that most people like. True, some people would feel that it’s a little bit too mainstream, but others would reason that hey, if it’s good enough for everybody else, it’s good enough for me!
Another exotic tonewood is making a name for itself in the guitar industry. It’s similar in appearance and sound performance as Mahogany. It has a distinctive punch for the mid-range tones, but it emphasizes the bright trebles that can be an asset in music when you achieve pitch-perfect intonation. The Martin Road Series DRS1 Guitar sports Sapele beauty perfectly!

Dive bomb is a guitar technique in which the tremolo bar is used to rapidly lower the pitch of a note, creating a sound considered to be similar to a bomb dropping. One of the most recognized pioneers of this technique is Jimi Hendrix. Other notable musicians who are widely known for using this technique are Eddie Van Halen and Joe Satriani. - winner333
Now that you’ve learned how to purchase a guitar, how to play guitar chords, and the basics of playing a guitar, you’ll just need to maintain practice! Use the ChordBuddy device as long as you need to, removing tabs as you progress. You’ll be ready to perform for your family and friends in no time at all. When you see how easy it is to finally practice and play the guitar, you’re not going to want to give up! See how ChordBuddy works, and discover how beginners, teachers, senior citizens, people with arthritis, and those with disabilities can play the guitar. To contact us, click here or call 877-947-2641.
Lastly, if you fancy yourself the next Slash, Jimmy Page, or Pete Townshend… you’ll want to pick up a Les Paul style guitar. It’ll get you that classic rock sound that you’re looking for. Les Pauls are equipped with “humbuckers” which produce a fat, meaty sound that’s rounder and less sharp than the single-coil pickups of a strat. The signal is also stronger so you’ll get more sustain.
The basic function of the volume knob is to change the level of your guitar’s volume output in a smooth and even way. But there’s more to it than that. Some players use the volume knob as a means of boosting their signal to make solos pop out. For example, if you keep your volume dialed in at seven or eight and perhaps lean on your amp a little more for output, you’ve got two or three more notches to ride your loudness up via the knob when it’s really time to burn. No need to spend money on a volume pedal, and unlike distortion or overdrive pedals this doesn’t change your sound much.
It’s easy to remove your pickup or pickguard and slide some foam rubber behind the unit. Start with soft foam first, and then increase the density to find the difference you like. Conveniently, the gray foam used in aftermarket pickup packaging makes great damping material: It’s soft enough that you can double it up (see Fig. 1 and 2) to create more pressure on the pickup’s back plate, too. This is a relatively no-frills mod that requires minimal materials and tools.
{"eVar4":"used: guitars","eVar5":"used: guitars: electric guitars","pageName":"[gc] used: guitars: electric guitars: supro","reportSuiteIds":"guitarcenterprod","eVar3":"used","prop2":"[gc] used: guitars: electric guitars","prop1":"[gc] used: guitars","evar51":"default: united states","prop10":"condition","prop11":"used","prop5":"[gc] used: guitars: electric guitars","prop6":"[gc] used: guitars: electric guitars","prop3":"[gc] used: guitars: electric guitars","prop4":"[gc] used: guitars: electric guitars","channel":"[gc] used","linkInternalFilters":"javascript:,","prop7":"[gc] used"}
That's right. It's neck first, then bridge height, then intonation (at least the way I do it). Nut height can be taken out of the equation by putting a capo on the first fret, so it can be sorted out later if there are any problems with it. Of course if you were to put a capo on the first fret, you'd need to compare that with the 13th fret when setting up the intonation.
As I commented above, my go to method for quiet practice is a PocketPod with Shure headphones. But, who doesn't like plugging in to an amp every once in a while? I live in a house, but the neighbors are close. The amp I use is a Fender Super Champ XD, which is a 15w tube amp with some digital effects. It seemed quiet enough at low volumes, but your mileage may vary. If I were you, I would at least give one a listen at a music store and see if it can do what you need.

Think of where you presently are in your journey as merely preparation and training. You are getting in shape to learn to play by developing some basic skills and building finger strength and callouses and coordination. Progress will be very slow in the beginning but if you persevere, you will reach a point where progress comes at a far more rapid pace.

Here we have is one of the finest vintage Banjo's you will ever see. This example is a 32 year old High End no expense was spared. Its super well built with top grade materials like Brazilian Rosewood fingerboard and Mother of pearl inlay work just about everywhere WoW!... just have a good look at its AAA flamed Maple back and its AAA flamed Maple Neck.. this one is super nice and well its clean. The action is great and she has a very good feel & sound. More to come soon...stay posted for updates Thanks for looking. .

Basicly it is a HD digital sound interface plus with a MIDI controller and footswitch. It is has unique design with different HOST mode and switching MODE to work with the host softwares. We are proud of that it is now maybe the best thing you can find to use on stage with software FX. The special designed analog signal chain mixing with the digital codec give the best dynamic response and sound quality. We did AB with lots of other interface and be so confident on its performance.
ESP Guitars makes seven types, the Eclipse series, James Hetfield Truckster, and Kirk Hammett KH-3 from ESP, the LTD EC series and Truckster, the Edwards E-LP series, and the Navigator N-LP series, which are based on the Les Paul design. Certain EC models have 24-fret necks and active electronics using EMG pickups instead of the standard passive pickups and 22 frets found in the traditional Les Paul. The Edwards and Navigator lines are made in Japan, and available only on the Japanese market; they come standard with Gotoh hardware and Seymour Duncan pickups (EMG pickups in a few models), and unlike the EC and Eclipse series guitars, which are updated variants on the Les Paul, these are made to be as close to the Gibson 1959 Les Paul design as possible, in the vein of the late 1970s and 1980s “lawsuit” model guitars from Tokai, Burny, and Greco, complete with Gibson style headstocks.
Overdrive pedals are intended to mimic the sweet sound of an overdriven tube amp. They are generally more subtle, warmer and a bit richer in sound. Overdrive pedals typically don’t produce the kind of heavy distortion needed in hard rock and heavy metal, but they are fantastic for blues, country, rock and anything else where you need warm, textured distortion. A good example of a quality overdrive pedal is the Ibanez Tube Screamer.
Examples of these first Supros can be seen in two catalogs from 1936, by Canadian distributor Peate and the Bronson Music & Sales Corporation, the latter probably originating slightly later than the Peate book. Both show laps identical to the Supro frying pan. Peate offered the Spanish guitar and mandolin. In the Bronson catalog, the Supro frying pan is known as the Bronson Singing Electric “For The Artist.” Bronson also sold electric Spanish and tenor guitars and an electric mandolin, other early Supro electrics.
There’s also the line of self-tuning “robot” guitars that Gibson spent more than a decade and millions of dollars developing. In 2015, Juszkiewicz made the feature standard on most new guitars. Sales dropped so dramatically, as players and collectors questioned the added cost and value, that Gibson told dealers to slash prices. The company then abandoned making self-tuners a standard feature. You can still buy them — they call them “G Force” — but they’re now simply an add-on option.

The guitar output jack typically provides a monaural signal. Many guitars with active electronics use a jack with an extra contact normally used for stereo. These guitars use the extra contact to break the ground connection to the on-board battery to preserve battery life when the guitar is unplugged. These guitars require a mono plug to close the internal switch and connect the battery to ground. Standard guitar cables use a high-impedance 1⁄4 inch (6.35 mm) mono plug. These have a tip and sleeve configuration referred to as a TS phone connector. The voltage is usually around 1 to 9 millivolts.