We are really proud of our instruments, but what makes us most unique is our people, and your access to them. The world is full of faceless guitar companies, most are big conglomerates. We have a team of passionate guitar people and are committed to giving you unprecedented access to our team. Each member of the team is focused on supporting you. We treat each player like a Michael Kelly endorser. We value personal relationships with Michael Kelly owners and work hard to give you a level of service not readily available from other guitar brands or retailers. Let us help you get the right instrument!
The Dean Custom falls right in the middle-range for guitars under $500. For around $350, this guitar has some great perks such as the Floyd Rose locking tremolo. The beauty of the Floyd Rose is in its ability to keep the guitar in tune even during crazy changes in pitch. Greats like Steve Vai and Eddie Van Halen are just a few notable artists to rock out using the Floyd Rose. With a carved flamed maple top and a lightweight basswood back, this guitar has the looks, the sound, and the ability to keep rocking in tune no matter what you throw at it.
Though these pickups can be modded to fit in other guitars, the Antiquity Jazzmaster flat coil design is intended to serve as an upgrade to the Fender or Squier Jazzmaster series. Popularized in the late ’50s and ’60s, the classic Jazzmaster tone is rich and crisp but, without harshness on the higher register. This pickup comes in both a neck and bridge version that work together to cancel noise and produce that same rich tone with some extra snap and good string response coming out of two Alnico magnets.
Directional mics, such as cardioids and figure-of-eights, exhibit different frequency responses off axis — broadly speaking, off-axis sounds tend to be duller, although it's a complex effect which is different for each model. Professional producers are well aware of this, and employ the effect to refine their sounds. For instance, Chuck Ainlay comments "I'll usually start with a [Shure SM57] on the amp; but not straight on axis with the middle of the speaker; it's usually off-centre, angled towards the middle of the speaker and generally just off the grille." Jay Graydon refers to a fairly similar setup: "I position the mic about one inch left of the edge of the speaker-cone centre, using a 22-degree angle, and about one inch back from the grille cloth." Andy Johns, on the other hand, has said that "the miking technique I used on electric guitars for years was two [Shure SM57s], one straight on, and one at 45 degrees. Put 'em together, and it always works."
Why We Liked It - The Martin DRS2 will take some beating as one of the all-round best electric acoustics you can buy, simply because you’re getting the finish and tonal quality of a much more expensive guitar for a solid price. Whether you’re mainly looking for a traditional acoustic you can occasionally amplify, or you need something professional grade for gigs, this could be it. In terms of recording your guitar, you can mics for guitars or a microphone for the guitar amp. If you're looking for an alternative, check out the Martin Road Series DRS1 Dreadnought.
I have located a semi-hollow body electric Kent guitar that has a body some what like a 335 and the neck like a fender strat. The body is a beautiful natural birdseye maple. She is in awsome shape and plays well. I have the ser# (xxx) 3 digits and I believe that it was made in Japan in the Sixty's. I have no Idea what model it is or value because I can't find out any thing about Kent guitars. I've seen Kent amps guitars & drums but no info. I welcome anything.
Ovation, Roundback, Adamas, Legend, Custom Legend, Elite, Applause, Celebrity, Balladeer, Ultra, Thunderbolt and Lyrachord , The Roundback body shape, Roundback design and Roundback Technology, Guitar Bowl Shape, Fingerboard Inlay Design, Sound hole Rosette Design, Adamas Peghead Shape, Bridge Design, Epaulet Design, Soundboard and Sound hole designs, Guitar Tuning Head are protected by one or more US and Foreign Trademarks and Patents.
The MC5 was founded by guitarists Wayne Kramer and Fred “Sonic” Smith, friends since their teen years and veterans of the Detroit garage rock scene. They honed a two-guitar attack that owed much to the heavy rock sounds being popularized at the time by acts like Cream, the Jimi Hendrix Experience and Led Zeppelin. But Kramer and Smith laid down their riffs with more reckless abandon and a greater sense of desperate urgency than any of those groups.
Analog overdrive/distortion pedals work on similar principles to preamplifier distortion. Because most effects pedals are designed to operate from battery voltages, using vacuum tubes to generate distortion and overdrive is impractical; instead, most pedals use solid-state transistors, op-amps and diodes. Classic examples of overdrive/distortion pedals include the Boss OD series (overdrives), the Ibanez Tube Screamer (an overdrive), the Electro-Harmonix Big Muff Pi (a fuzz box) and the Pro Co RAT (a distortion). Typically, "overdrive" pedals are designed to produce sounds associated with classic rock or blues, with "distortion" pedals producing the "high gain, scooped mids" sounds associated with heavy metal; fuzz boxes are designed to emulate the distinctive sound of the earliest overdrive pedals such as the Big Muff and the Fuzz Face.
There are two common types of 5-way selector switches in the guitar world – the Fender type and the “import” type. Both types are functionally identical but differ in physical layout. It’s easy to see which type you’re dealing with. The Fender-type switches viewed from below have two rows of 4 contacts, either side of the circular body of the switch. The import-type switches have a single row of 8 contacts in a line.
The Effect: Vocal harmonizer pedals are among the most powerful tools you can have as a singing guitar player. An average vocal harmonizer will use the input from your guitar, mix it with your microphone’s signal, and produce a harmonic background of your voice that is in tune with the chords you’re playing. More advanced models like TC Helicon Play Acoustic, are capable of doing much more than that. We are looking at complex processors that offer multiple effects, active vocal equalization and so much more. With that said, vocal equalizers come in a variety of flavors. Some are optimized for solo performers, while others are much more relaxed. The great thing about modern vocal harmonizers is that tracking is no longer that much of an issue. It is fair to say that most models you can find on the market right now, will get you pretty solid core performance.
In addition, there were other assessments. I went to Guitar Center to buy an amp. I was playing my guitar through a vintage tube amp when I noticed a man standing behind me. I said, “It sounds good.” He said “It sounds really good, are you going to buy it” as he pointed at my guitar. It was then I realized he was a customer and was interested in buying my guitar.
Whatever budget you’re on, you will always be able to find a suitable guitar. Even in the $100 price range you can find some models that play nicely. However, in that super-budget market there is a lot of garbage, so be careful. There’s a difference between ‘affordable’ and ‘cheap’, so do your research before buying something that may offer no value.
Most guitars will have at least one TONE knob - a way to adjust the frequency spread of the signal going to the amplification system. Similar to a TONE adjustment on radios, stereos, other things; it usually is a means to adjust how much of the higher frequencies are sent to the output. Rolling the knob “back” will reduce the higher frequencies and can help make the guitar sound less “shrill” if it exhibits that tendency.
The neck, which extends from the guitar body, includes the fretboard and headstock on which the tuners are mounted. It contains a metal truss rod that prevents neck bowing and twisting, and can be adjusted to help the guitar maintain consistent pitch. The fretboard is usually made from a thin layer of rosewood or ebony, although some models, usually with maple necks, have a fretboard made of the same wood as the neck. Most fretboards have position dots or other markers inlaid in the fretboard. Some models have markers on the upper edge of the fretboard offering the player easy visibility.
Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Custom - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Diecast, Gold, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Ivory, Sunburst
Editorial comment – I advise folks when considering fretwork to consider not choosing a size or leveling operation resulting in less than .040” height if they want to play a style with frequent fret hand slurring, i.e. rock, blues, shred etc. Low fret height is less capable of sustaining a reasonable fret leveling in the future, making it that much closer to refret time. You don’t have to choose a very tall size if that is uncomfortable for you, but only choose a low height if that is really what you want and are accustomed to.
Washburn is an EXCELLENT brand. I have owned an N4, 2 N2's, and their latest, cheapest Nuno model for my daughter. My daughter's guitar is amazing for the price I wish I had such quality for my starter guitar. I would put my N4 up against ANY guitar- period. Plus, whenever I have contacted the company, they have top notch customer service. I know this isn't about amps, but I wrote them about an issue I had with my Randall amp ( a division of Washburn). Without me asking, they mailed me an amp part with an apology. Top notch.
While high action is a concern, I see more people on guitar forums who bought Authentics, including the 1941, who say the action and playability is “like butter” more than I see people mentioning high action being a problem. Also, a lot of players rarely go beyond the fifth fret without a capo, so they may not even notice if their 10th fret would seem high to some players.
We make our Tone Bars / Ferrule Blocks (tone slugs) out of 360 brass and use them on most all of our string through custom guitars. You will notice an enhancement in sustain and beauty. The ones sold here are not polished. Go to shawwoodshop.com to purchase slugs that are polished. Please ask any questions you might have about the Slug. I offer quantity discounts.
Many experiments at electrically amplifying the vibrations of a string instrument were made dating back to the early part of the 20th century. Patents from the 1910s show telephone transmitters were adapted and placed inside violins and banjos to amplify the sound. Hobbyists in the 1920s used carbon button microphones attached to the bridge; however, these detected vibration from the bridge on top of the instrument, resulting in a weak signal. With numerous people experimenting with electrical instruments in the 1920s and early 1930s, there are many claimants to have been the first to invent an electric guitar.
While National blithely ignored Beauchamp’s electric experiments, their competition – Dobro – was next to enter the electric arena as early as 1933, with the introduction of the Dobro All-Electric. Basically, the All-Electric was a mahogany-bodied Model 37, most usually outfitted with a 12-fret square neck. It had a large lightning-bolt-engraved coverplate, two screen holes, three little holes under the fingerboard, a slothead, and rosewood ‘board with dot inlays. Instead of the usual resonator, this had a large metal plate where the cone assembly would normally be and a Stimson pickup mounted just in front of the bridge, curiously enough with the poles slanted from the bass side near the bridge toward the middle on the treble side.
When it comes to acoustics, you can’t beat Taylor’s eco-sourced Tone Woods. The 114e features a solid Sitka Spruce top and layered Sapele back and sides, giving the Taylor a rich and full-bodied sound that is hard to tell apart from solid wood bodies more than twice the price. The electrics and built-in preamp are top notch and you can’t beat that Taylor neck for finger-friendliness if you’re just starting out with chords.
I’m Björgvin Benediktsson. I’m a musician, audio engineer and best-selling author. I help musicians and producers make a greater impact with their music by teaching them how to produce and engineer themselves. I’ve taught thousands of up and coming home studio producers such as yourself how to make an impact with their music through Audio Issues since 2011.
The Epiphone ES-335 Dot was the world's first semi-hollowbody electric guitar, introduced in 1958. Today, it's made by Gibson, but it is still prized by jazz and blues musicians looking for a classic sound. Setting up the Dot involves adjusting the truss rod to correct for any underbowing or overbowing of the neck because of humidity changes. The bridge saddle on the Dot may also be adjusted to get the right distance between the string and the fretboard, called the “action.”
Unintentional phase cancellation can also occur if a guitar's pickups are wired incorrectly, or if a new pickup installed in the guitar has different magnetic or electric polarity from the one it replaced. To fix this, the pickup's magnetic or electric polarity needs to be reversed (which one exactly depends on the respective polarities of the other pickup(s) and whether or not hum-cancelling combinations are desired). While the latter is usually a small matter of reversing the pickup's hot and ground wires, the former may be more difficult, especially if it requires the magnet(s) to be removed and reinstalled in a different orientation, a process which can damage the pickup and render it unusable if not done carefully. This is the case with most humbuckers. On the other hand, single-coil pickups with magnetic polepieces can simply be repolarised by applying a strong enough external magnetic field.
Tube or solid-state? One has the nice warm vintage tone, but the other is just so much simpler and free of hassle. Vox make one of the best hybrid amps, which heats up your guitar signal with a proper 12AX7 tube in the preamp before it becomes amplified by conventional transistors to deliver up to 30 Watts. A warm tone with smooth overdrive, but without the aggravation.
In a very basic sense, your pickups create a magnetic field that is disturbed when guitar strings are vibrated above it. This, in turn, converts the vibration of the guitar strings into a current. The current is then sent through to your output jack where the signal then passes through your lead into your amplifier, where it is amplified. Different gauge strings vibrate at different rates e.g. an A string will typically vibrate at 440 cycles per second (440 hertz) which creates a current of 440 hertz in the pickup.
VintageSilvertones.com is a curated collection of electric guitars chosen for their unique tone, design, and significance in electric guitar history from approximately 1950-1980. This collection approaches electric guitars from the underdog perspective. So we carry guitars built for the masses, luthiers & manufacturers who pushed the boundaries as to what was possible in terms of not only instrument quality but tone. Design also plays an important consideration in this collection. Alternative materials, innovative tuning systems, and high quality-low cost manufacturing processes are only some of the unique qualities found on instruments at VintageSilvertones.com.
If you see "PM," play using palm muting. For standard right-handed guitar playing, gently lay the edge of your right palm across the strings near the guitar's bridge. When you strike the notes (with the same hand as is providing the mute), you should hear the tone of the note, but with a subdued, dead quality. Move your hand slightly up the strings toward the neck to deaden the notes more.
ESP is notable for using active pickups — as opposed to the nearly universal use of passive pickups. Active pickups make use of internal amplification inside the guitar, so that the pickups produce a hotter, louder, and richer sound. The concept is very effective, however it requires the incorporation of a 9V power supply inside the guitar. This can be a great inconvenience if the battery dies and the guitar is not playable.
Some of the earliest electric guitars, amps-in-cases, pickups under the bridge, fiberglass guitars, built-in electronic vibratos. Sound curious enough for you? The subject of Supro guitars and amplifiers represents a profitable avenue for exploration by collectors and enthusiasts interested in the many curious and significant byways off the guitar superhighway, which can be enjoyed without having an oil sheik’s bankroll. While National resonator guitars have received superb attention by Bob Brozman, little has been written about this mysterious corner of the Valco universe. Well, with a little help from our friends (in particular, catalogs and invaluable information supplied by Mike Newton, Jim Dulfer, and Michael Lee Allen), let’s set the record straight.
This Charvel is the signature model for Guthrie Govan, widely regarded as one of the finest guitarists around. Its caramelized ash body model is also up there with the finest bolt-ons we’ve ever played. The neck is extremely tight-fitting and held in place with four screws, each recessed into the contoured heel. Like any HSH set up you have huge choice on exactly how you wire it - this is no different. While the outer positions select the full humbuckers, position two voices bridge (slug single coil only) and the middle single coil; position three gives us bridge and neck (both slug single coils); position four offers the screw single coil of the neck pickup with the middle pickup. A ‘secret’ two-way mini toggle that simulates a coil-split via an old-school passive filter (a 0.1 microfarad capacitor). In many ways this feels more like high performance rifle, not a guitar. It gives off a tuned-to-perfection vibe that’s like an instrument you’ve owned for a while, gigged, modified and tweaked. Which in reality is exactly what it is only Charvel and Guthrie Govan have done it for us. But don’t dismiss this as a virtuoso rock shredder axe. Yes, if your technique is up to it, you won’t have a problem there and using just the bridge pickup you’ll probably have all you need: big and ballsy, a hint of a cocked wah-like high end it’s certainly in the JB area. But it’s offset by a pokey PAF-like neck voice, tube-y and soupy but far from one dimensional. If that was it, we’d be smiling. But there’s plenty more... Guthrie Govan’s vision for an all round workhouse that’ll stand up to the rigours of professional touring is superbly realised in this signature. Every detail is wonderfully considered. It’s not a cheap date, but it’s an astonishing guitar: a player’s tool of the highest calibre.
Eric Clapton was in a bad mood during the photoshoot for Blues Breakers. The 1966 Clapton/John Mayall collaboration sees Clapton on the album art reading a copy of UK comic book the Beano. He was so aghast and bored by the idea of a photoshoot that day that he refused to make eye contact with the photographer, therefore settling on staring at a comic instead. Nicknamed “The Beano Album”, it’s often considered to be one of the most important guitar recordings ever made.
Now we’ve got the basics down, let’s have a look at some simple modifiers to the circuit. This article first shows you how to add a “killswitch” to the guitar, then uses the lessons learned from that process to change that killswitch to a volume control instead. Finally, we’ll find out how capacitors are used in guitar circuits and install our first tone control.
Shouldn't even be questioned. Ever hear of 'Voodoo Child'? Yeah, that was recorded in one take. & almost entirely improvised. & it's the greatest recording of an electric guitar being played EVER. & this isn't from some idiot who just listens to a lot of music, I play the guitar and have done a lot of reading and I know a few of your favorite guitarists would agree with me.
This extremely limited Marshall 1936V 2x12 Silver Jubilee Guitar Speaker Cabinet has been created to get the best sound out of your Silver Jubilee heads, most notably the 2555X and 2525H Mini Silver Jubilee tube amp heads. The Silver Jubilee styling looks great on stage and the 2 x 12” Celestion G12 Vintage 30 speakers provide you with all that gorgeous amp tone – perfect for 1980s/1990s hard rock.
There’s an old joke in the technology industry: If a product has a problem, simply sell it as a feature. The electric-guitar-effects industry is no different. Music has often thrived on transforming faults into influential sound effects. Before professional studio production enabled granular tweaks in sound, standalone guitar effects emerged from deliberately converting hardware faults—often caused by the limitations of amplifiers—into positive features. By the end of the 1970s, it had become impossible to imagine how R&B, blues, and rock could have existed without these fortuitous mistakes.
Second, just like removing the pickup selector, you will need to access the back electronics cavity or remove the pickguard. Refer to the pickup selector section for more details. Take note of what wires are soldered to what lugs before you remove the pot. If you are not familiar with electric guitar wiring, I suggest that you draw a picture of the selector and label the soldered wires. Once you know where everything has be wired, you can cut the wires close to the lugs and remove the old pot. Then you can bolt the new pot in place, solder the wires on the lugs, replace the cavity covers or pickguard, and replace the knob. For more information about how to solder wiring, see the soldering page.
That's right. It's neck first, then bridge height, then intonation (at least the way I do it). Nut height can be taken out of the equation by putting a capo on the first fret, so it can be sorted out later if there are any problems with it. Of course if you were to put a capo on the first fret, you'd need to compare that with the 13th fret when setting up the intonation.
Look for additional symbols in the tab. As you can see in the example above, many tabs aren't just collections of lines and notes. Tabs use a wide variety of special symbols to tell you how to play the notes in the tab. Most symbols refer to specific playing techniques - to make a song sound as much like the recording as possible, pay attention to these special markings.
If you are not attracted to the way the guitar looks or feels in your hand, chances are you won't be too eager to pick it up every day. When you are just starting out, this is supremely important. Here's where a disclaimer needs to be placed. This isn't always the case, and often times people warm up to a guitar even if they didn't initially like it, but why chance it?
Now imagine the puddle again, but this time imagine some wood blocks (12 inch long 2x4's for those of you with rusty imaginations) that are placed on their sides in the puddle in the shape of a three-sided box with the open side facing the pebble's point of impact. The radiating lines go in to the box and bounce back or reflect off the walls. Soon, there are so many lines radiating around in that imaginary box that they all collide with each other and become a random, jumbled mess. Eventually, the size of the lines and the number of them diminish. That my friends is reverb.
Like most affordable super strat guitars, the Omen-6 has a basswood body, carved into the elegant looking shape that Schecter is known for. The neck is crafted from mahogany and joins the body via a bolt-on joint. It is topped by a 14" radius rosewood fingerboard that has 24 jumbo frets. It comes setup for fast and comfortable playability, with its 25.5" scale length, 1.65" nut width and stylized fretboard markers. Giving this guitar its voice are two Schecter Diamond Plus pickups, which are passive pickups but are still hot enough for driving high-gain pedals and amps.
No matter your vision, SparkFun's products and resources are designed to make the world of electronics more accessible. In addition to over 2,000 open source components and widgets, SparkFun offers curriculum, training and online tutorials designed to help demystify the wonderful world of embedded electronics. We're here to help you start something.
Though you can certainly buy any guitar of your choice by looking at the specs, this is not something a true music lover would do. If you get attracted towards guitars after being inspired by your favorite artist, then what you expect is to have your guitar produce that particular tone which your idol does. Of course, you cannot produce that typical signature tones from any guitar model. But how about if you get that guitar which your artist have?
Jackson is another great American guitar manufacturer that has been at the peak of popularity a couple of decades ago. These days they are still considered to be an authority in the industry. Current Jackson lineup includes some of their legendary models revamped in a new edition, as well as brand new guitars. People are usually divided when it comes to Jackson, but no one can claim that their guitars are not among the best.
The Line 6 POD Farm program is famous for its amp simulation, however many users have realized that the quality of its modeled effects are equally superb. Some even use the POD Farm strictly for its effects! It has a huge collection of FX - up to 94 - and it modeled some of the most popular stompboxes including the MXR Phase 90, ProCo Rat, Uni-Vibe, Arbiter Fuzz Face and Big Muff Pi. It also includes modeled versions of old analog devices like the EP-1 Echoplex. Setting up is a breeze with its simple carousel-style interface, which lets you visualize your signal chain. Current Retail Price $49.00
Breedlove Guitars was established in 1990 by luthiers Larry Breedlove and Steve Henderson, while working at Taylor Guitars. After moving to Oregon, Breedlove and Henderson began specializing in custom, fingerstyle six and twelve string guitars. In 1991 the first Breedlove guitar model appeared, after experiments with the JLD bridge truss system and various bracing techniques. Around 1994, Larry’s brother, Kim Breedlove, joined Larry and Steve as a master craftsman. Breedlove strives to be environmentally conscious, and is “dedicated to selecting alternatives to endangered rainforest woods.” Breedlove has since expanded to include mandolins and ukuleles.
South Korea has been one of the largest OEM guitar factories in the world since 1980's. Nonetheless, the words "Made in Korea" still invoke visions of low cost alternatives to high-end manufacturers. At Swing, our mission is to lay these stereotypes to rest, and show the world that we can produce true professional grade instruments, made by professionals, for professionals. (Of course, company is not a patriotic organization. This is a matter of manufacturer's pride and self-satisfaction that can be called "Professionalism".)
There was a band in Manchester called Sister Ray, who were just this scary bunch of men/reprobates. I guess word had got around that I had a knack and was a useful little guy to have around, and you only have to buy me some Coca-Cola and I was good to go. So I played with them. I started playing my first sort of shows in front of real [crowds] when I was fourteen.
The guitar features hand-rubbed solid Sitka Spruce top supported by Martin's incredibly reliable mahogany HPL (high pressure laminate) back and sides, essentially similar to the configuration found on many of Martin's mid-priced acoustics. If you're looking for an affordable starting instrument that has big-brand backing, or you are looking to get into the parlor-style guitar trend, check out the LX1E Little Martin.
Back in the control room, audition each mic, preferably as the guitarist plays along with the other instruments. Listen carefully to how each microphone sounds on its own and, more importantly, to how it works in the mix. Usually, one microphone will come up a winner on the first pass. Don't stop there, however. Instead, leave the "winning" microphone where it is and experiment with the placement of the other two mics. Time-and mic selection-permitting, you may also wish to do a second round of testing with other microphones.
Well technically, the floor and the ceiling do shape the tone, post amp. Room acoustics are a major factor in the quality of sound recordings. Also Dan isn't wrong. Each thing that vibrates that eventually moves the pickup (while a note is being played or sustained) will disrupt the magnetic field. In physics there is hardly ever an instance where things have absolutely zero effect on the things around them. It comes down to the significance of the effect. For example, if something moves the pickup .05 picometers six times a second, then it likely has a negligible effect on the sound (i.e. our ears are not capable of detecting any difference. There does come a point where other variables do begin to change the characteristics of the sound. Additionally, as a string is struck, due to the rigidity (or slight lack thereof) the neck and body will vibrate, changing the distance between bridge and nut. The shortening and lengthening of this distance will then change the vibration frequency of the string. This can result in the dampening of vibration or potentially slight amplification of frequencies or overtones. Overall, it is impossible to say with absolute certainty that something does not have an effect on something else in this case. The truth, however, is that the degree to which the change is noticeable may not be detectable by the human ear.
These guitars work in a similar way to solid-body electric guitars except that, because the hollow body also vibrates, the pickups convert a combination of string and body vibration into an electrical signal. Semi-hollowbodies are noted for being able to provide a sweet, plaintive or funky tone. They are used in many genres, including blues, funk, ’60s pop and indie rock. They generally have cello-style F-shaped sound holes, though these can be blocked off to prevent feedback, as in B.B. King's famous Lucille.