As these same makers ramped up for digital production, digital choruses naturally joined the team. The effect as produced digitally might sound broadly similar, but it is done differently than in the analog circuits. Digital chorus pedals double a signal and add delay and pitch modulation to one path, the latter wobbling below and above the pitch of the unadulterated signal, which produces an audible out-of-tuneness when the paths are blended back together. It’s hard to fault the power and range of control that digital technology affords, and this version of the effect has been hugely successful, but many guitarists still prefer the subtle, watery shimmer of the analog version. Conversely, the same ears often find the digital variety makes them a little queasy.
The Kremona “Sofia” model is handmade in Bulgaria as well with a fantastic support staff to answer any questions, so if you have concerns about items made in China, you can lay those concerns aside. The top is cedar, with an authentic bone nut and saddle, and solid African sapele back and sides complete the look for a very pleasing appearance and sound.
The characteristics of your Kingston are very similar to what other owners have reported: occasional scratchy and erratic performance of the electronics, intonation problems, and action that is hard to control (notably due to the lack of a truss rod). Although I can’t verify this, one estimate indicates that over 150,000 Kingston guitars were sold in the U.S. during the 1960s! It’s obvious that quantity trumped quality when it came to producing the guitars, and it isn’t surprising that the electronics have some issues after all these years.
SOLD OUT: Here we had a 40+ year old 1972 Alvarez 5080 Acoustic guitar that was built by the master guitar builder Kuzio Yairi. He used 30 year old vintage aged tone woods when they built this guitar over 40 years ago.. that would make this wood arround 70 years old... Thats can say that about a new Martin can we... not going to get tone like this from a new Martin either. This is one high class example replica of the Martin 000-28 this model is quiet rare and beautifully adorned with exotic tone woods plese refer to the pics. Just have a look at the beautiful exotic old growth Jacaranda Brazilian Rosewood back, sides, fingerboard...headstock overlay .., ebony pins with MOP and brass ring all high end classic detailed appointments... notice the real patina this guitar plays real well and has been played and it shows... in a good way to my eyes.. I love it. So will you just have a look... no visable issues, no cracks to be found, inlays, bindings, pickguard, tuners,frets.....all good..and sound is rich and has a nice sustain and is a pleasure to play... fresh from the JVG shop with a fresh bone saddle & nut & new Martin Marquis strings sweet! A must HAVE 40 YEAR OLD VINTAGE YAIRI 000-28 STYLE, Claptons favorite for good reason... SORRY THIS GUITAR HAS SOLD Thank you for your interest.
Delay pedals take your original signal, a guitar chord or note for example, delays it and plays it back exactly how the pedal hears it the first time. It can either play the note back once or multiple times depending on your settings or “feedback time”. Often, you’ll see Digital Delay pedals as well as Analogue Delay pedals. The major difference is that digital delay pedals will offer longer delays and a ‘cleaner’ exact sound, however guitarists often prefer the analogue sound for all the subtle nuances and slight unpredictability in sound. This comes down to personal preference but both options sound great.
Two new models that would eventually become mainstays joined the Teisco line in ’65. Theye were two double cuts with slightly more flared horns, in a sort of tulip shape. Both had a single, wide, chrome-covered pickup with poles exposed along one edge. This was similar to the old MJ-1 but by ’65 would become the new SM series. Both had bolt-on necks with bound rosewood fretboards and the top-edge rectangular inlays. The E-100 had a bridge/tailpiece assembly, volume and tone on a small pickguard, and one of the elongated Strat-style heads. The ET-100 had a platform vibrato. As a sign of things to come, the Teisco Del Rey ET-100 had a regular Strat-style headstock, the first to appear on Teiscos, as far as I’m aware.
In 1962 or 63 (possibly as early as 1959) Guyatone guitars began arriving in the U.S.. If you look around the internet you will see that they could be found under a variety of brand names and were sold in drug stores, department stores, even auto parts stores, as well as music stores. There were two lines of Kent guitars: a Standard series and a “Pro-series”. They were made by Teisco and Guyatone. I haven't been able to get my hands on any of these early solidbodies so I don't know if "the Professional Group" guitars are actually worthy of the "professional" designation and slightly higher pricetag or if it was all about marketing.
Digital reverbs, like their sibling delays, offer more power and a greater variety of settings. And in addition to doing some approximations of spring reverb sounds, digital units usually offer more “lifelike” reverberation as heard in anything from an empty room to a large concert hall, if you want to add a synthesized “natural” room sound to your signal rather than merely replicate the classic sproing of springs. A few pedals do this very well, but most such devices are rack units that are best used in an amp’s FX loop, and are beyond the scope of this article. For all the power of digital reverbs, however, there are plenty of guitarists who just don’t warm to them, and the tube-driven, analog, spring reverb effect remains hands-down the favorite for guitar.
The process of building our kit guitars and basses is straight forward and requires little experience in woodworking or in instrument building. The entire instrument can be assembled with a few simple tools. Setting the instrument up for your playing style is also straightforward. We will guide you though the basic process in our instruction manual. For more complex or particular setup requirements, we suggest that you work with a professional for setup - just as you would with any instrument that you purchase.
This processor is pretty good quality, unfortunately not too many parameters on the effects and you can only use one effect at a time, and some prefixed combo of 2 effects (if i remember correctly 10 different options). If you need it for reverb, or slight delay, tremolo or acoustic simulator its pretty cool, not able to add exact tempo on delay or tremolo though. Sound quality is very good, 24 bit A/D and D/A so no loss there either, and you also have stereo (same effect options on both though) and balanced and unbalanced outputs (if you use unbalanced the signal goes to both outputs so you also have the balanced output if needed). For the money is definitely the best option, imagine that a reverb pedal cost the same money (just reverb) if you have a controller it will fit on your gear. I am using it with ... full review

The Chapman ML2's classic, single-cut body, two chrome-plated humbuckers and a black pennant headstock that’s not a million miles away from Gibson’s Les Paul. But appearances can be deceptive: this instrument is a very different beast. Chapman pegs its weight at a relatively svelte 3.5kg, so it’s unlikely to see you turning over your salary to the chiropractor. It’s also heavily contoured with its cutaway and heel carved for easy access to the upper frets. It has a modern, satin-smooth C-profile neck, hewn from maple (another deviation from the LP blueprint) and glued neatly to the body. The 25" scale lends it a unique feel - and with 24 jumbo nickel frets, the ML2 Modern is hugely shreddable. Both pickups feature an Alnico V magnet at the heart (think tight low-end, brightness, a little less on the mids), but with a coil-split, accessed by pulling up on the master tone pot, you can split the signal of these humbuckers for some single-coil snap and sizzle. The ML2 Modern makes a good claim on being all things to all guitarists. With coils split or not, we love its tone. That bridge ’bucker really sings with some gain. While the neck pickup is a great ‘rhythm’ humbucker - articulate and dynamic. Whether you find the modernity in its versatility, or in a feel that’s more Jackson than Gibson, the ML2 Modern sure lives up to its name.

THIS DELUXE PACKAGE INCLUDES - GIBSON'S LEARN AND MASTER GUITAR PACKAGE - PLUS 10 ADDITIONAL WORKSHOP DVDs. THIS IS THE MOST COMPLETE INSTRUCTIONAL GUITAR PACKAGE YOU CAN BUY. Winner of the Acoustic Guitar Magazine Players' Choice Award, two Telly Awards and an AEGIS Award for Excellence in Education, Learn and Master Guitar is widely recognized as the best home instruction course for learning guitar available anywhere. This deluxe package consists of 20 professionally produced DVDs, 5 Jam-Along CDs, a 100 page lesson book, and a free online student support site. It is the only instructional package you'll ever need on your journey toward mastery of the guitar.

Maybe the most well known amplifier released under the Peavey name, the 5150 is the result of a collaboration between Peavey and Eddie Van Halen. Debuting in 1992, the 120-watt, all-tube, two-channel head featured a searing lead channel that helped usher in a new wave of high-gain guitar ferocity in the early Nineties. Since Van Halen and Peavey parted ways in 2004, the model name was changed to the Peavey 6505 and has become an industry standard for modern metal bands such as Chimaira, August Burns Red, All That Remains and others.
bought at a tiny store in holland, back then they said to me the guiter was already 20 years old. he was looking a new, and bought it for 1000,- dutch guildens. thats maybe...445,- euro now. thats nothing compared to the prices they ask for a vox guitar they make TODAY! thay are building guitars again and ask pricies beginning by: 2000,- euro's. I wanna know when my guitar was bild, he has a chrome plate at the back with made by japan on it too.
Humbucker pickups were designed to deal with hum while also offering tonal characteristics beyond those of single-coil models. This design incorporates two single-coils wound together in series, with the polarity of the magnets arranged opposite each other. This design helps to eliminate hum. Hence it’s name. Humbuckers usually have a thicker, louder, more powerful tone when compared to single-coils. While they are very versatile, humbuckers lend themselves to rock, heavy metal, and jazz styles. Famous guitarists who use humbuckers include Slash, Jimmy Page, Joe Pass, and Duane Allman.
X-Series: Back and sides constructed from compressed wood fibers (high-pressure laminate or “HPL“) and solid Sitka spruce or HPL top. Due to this construction these guitars are more environmentally-friendly.[citation needed] Models include: DX1, DX1-R, DXM, DCX1E, DCX1R3, 000CXE Black, and 000X1. Some earlier models used ‘Ebonite’ (black Micarta) fretboards, later models use koa or striped ebony. Necks on all models are constructed from Stratabond, a laminated wood product used for decades in gun stocks and hunting bows. Some of the more recent models are made in Mexico.
Looks like a good guitar. I honestly think that for 90% of the hobbyist players out there, after buying better pickups, the difference between the sound of a Squier and a real Fender is negligible. I could be wrong I guess, but my ear doesn't really pick up enough of a difference to justify the money for a more expensive guitar. The quality of the guitar plays a big part for me. For instance, when I first got my guitar, the frets weren't smooth. Bends sucked because the note had lost it's sound by the time it was bent all the way up. Finally through playing and polishing, they flattened. Now they play really nice. I'm sure that on a new Gibson, that wouldnt happen. Oh well. About the Tele headstock that you didn't like, what don't you like about it? Do you like the gibson style 3 tuners to a side configuration?(like an acoustic?)
I always recommend the Cordoba C5 for beginners who are looking for their first classical or nylon string guitar. It’s comes at a very wallet-friendly price, but it sounds and plays exceptionally well for a guitar in its price range. More experienced players can look to other C-Series Cordoba guitars like the C12, which is built for advanced guitarists.
Though the line between the two is easily smudged, where multi-effects processors create a broad spectrum of effects, modeling processors can recreate the sound of particular instruments and amplifiers, like a Gibson Les Paul played through a stack of Marshall amplifiers, or a Fender Stratocaster played through a Fender Deluxe Reverb amplifier. A modeling processor offers you the ability to make your guitar and amp combination sound like whatever guitar and amplifier sound you want—even if you don’t own either guitar or amplifier. You are limited only by the number of models programmed into the modeling processor when you plug your guitar into one.
Advanced multi-effects processors can involve significant learning curves. Their hundreds of sounds and functions may entail diving deep into multi-layered menus to get at what you want. The best units offer intuitive and ergonomic user interfaces that keep the most common functions easily accessible via dedicated knobs and switches. Reading user and pro reviews can help you identify which models offer the greatest ease of use.

There are a very large number of acoustic guitar manufacturers in the world. However, not all are among the best, but this American brand specializes in acoustic guitars. You will find Martin guitars among the top 10 acoustic guitars in the world. It has greatly influenced the look and shape of the American acoustic guitars. Martin guitars are made from highly seasoned wood, which produces some really melodious tones. Mind you, these guitars can be expensive and taking care of the instrument is extremely important. It makes some extremely beautiful models like D-28 and D-45; however, they also manufacture budget-friendly models.

Sorry it has sold: Here we have a rather nice rare vintage 1970 Yairi & Son Classical acoustic guitar It's Label reads... Hand Crafted in Japan by Yairi & Son Model # 300 Serial # 177 Pretty darn low serial number 1970 remember she's 45 years old! Condition overall is very good - excellent used / vintage Not new or mint of course... Regarding its build quality She exhibits beautiful workmanship and superior materials Aged woods of over 30+ years old in 1970 when it was built! Tone-Woods now are in the 75 year range on this example looks like a Vintage masterpiece with its patina and look and feel I love these oldies funny thing is It still shines like glass to, amazing really when you think about it. This guitar has very good deep base tone and excellent volume and plays easily and comfortably the neck is nice and big 2" at the nut nice and wide feel to it. The neck is made of a high grade mahogany see pics, back and sides are also beautiful mahogany, with black or very dark brown bindings for a very classic look, the on the business end she has a wonderful quality solid spruce top with lots of bear claw figuring a really nice sound box it projects very well in deed... As you look at its back side in its entirety top to bottom it's hard to find a blemish I'm sure there are a few minors but it's really looking very clean and with a surprisingly shiny original finish... The front the headstock is pretty clean as well!...notice a bone nut has been fit, frets show little to no wear what so ever more than 90% remaining fret life, the fingerboard shows a little play action remember it's a 1970! ... The top as several chips and drinks and I have addressed them a touch up lacquer pen and just dabbed the tiny chip to prevent further chipping there it as a result after I polished it up turned out pretty darn good looking too, This guitar came to us as a partial trade with its bridge pulled nearly off by a ding dong previous owner that put regular gauge dred heavy gauge strings on it for long term and it lifted off in time, I removed all that cleaned up the woods & prepped it for a new vintage period correct Jacaranda rosewood classical bridge and glued it with hide glue clamping it up for 2 weeks & set her up with a bone nut & saddle and a new set of Dean Markley strings... This beauty comes with its original hard shell case black Tolex with a plush Marigold lining one bad latch but still functions well good hinges and handle so it's still ok. This is rock solid now as the Yairi & Son label says use only nylon strings. If you just use what Yairi suggested this would have never happened not Yairi's fault just the wild eyed idea gone wrong. Anyways she's back in action and sounding better than ever so if you like these old Yairi & Son classical guitars this may be a good consideration for you.... Let me know if you likeeee. Email Joe at: .
To ensure 100% customer satisfaction Bajaao offers 10 day return policy and we also pay for the return shipping to help you be free of the online shopping anxiety. Our content rich page is your one stop to get all the required information about the products be it the product description or the user generated hands on reviews. A friendly and knowledgeable staff is there to help you out with your queries should there be anything else you wish to know about the product, process, payment or after sale service. Our dedicated team will help you to select from the best of the products within your range. Call our experts to find out the best product to suit your style and need and buy Electric Guitars at the lowest prices in India.
The moral of this story is simple, if you have an old Terada, Yamaha, Ibanez, Suzuki, Yairi, Tokai, Takamine, Emperador, Morris, Pearl or Tama (yes! they made guitars to) just to name a few, you probably have a guitar that given the right bit of TLC will wipe the floor with most of its modern competitors, including those beautiful guitars that cost $2000.00 plus. Ok Then, enough of my yacking, enjoy the pictures.
In 2003 Fender offered Telecasters with a humbucking/single coil pickup arrangement or two humbucking pickups featuring Enforcer humbucking pickups, and S-1 switching. These models were discontinued in 2007. As of 2008, all American Standard Telecasters came with a redesigned Tele bridge with vintage-style bent steel saddles. In March 2012 the American Standard Telecaster was been updated with Custom Shop pickups (Broadcaster in the bridge, Twisted in the neck); the body is now contoured for reduced weight and more comfort.
If you wanted to wire a 4 conductor Dimarzio or Seymour Duncan in this way, just look at the diagram. Solder the 2 "middle wires" together, tape the connection, then solder the outer wires to the output. Be very careful when working with 4 conductor wiring. The colors and polarity are very important. You could easily make a mistake and wire an "out-of-phase" arrangement which would have low output, a squawky, thin sound AND the humbucker would NOT be hum canceling.

Another popular modification is to reverse the electric polarity of one of the pickups (or one coil of a dual-coil pickup). When two pickups are selected, this produces a very thin and weak sound, due to phase cancellation between the pickups.[21] The closer the pickups are to each other, the greater the cancellation and thus the weaker and thinner the resulting sound. In case of a humbucker this results in a sound that is so weak as to be almost unusable, as well as the loss of the pickup's hum-cancelling properties (due to the coils being magnetically out-of-phase, but electrically in-phase with each other).[22]
8dio sampled a 200-year-old Italian made mandolin to create a gorgeous sounding VST that simply rules, and will fool even the most well-trained ears into thinking it’s the real deal.  Like with the others in the series, we have our usual clean legato, artifacts, effects, tremolos, mutes — basically, you have everything you need to get the job done 99% of the time.
In the early 1980s, some performers began using two-way or three-way cabinets that used 15" woofers, a vented midrange driver and a horn/driver, with an audio crossover directing the signal to the appropriate driver. Folded horn bass guitar rigs have remained rare due to their size and weight. As well, since the 1990s, most clubs have PA systems with subwoofers that can handle the low range of the bass guitar. Extended range designs with tweeters were more the exception than the rule until the 1990s. The more common use of tweeters in traditional bass guitar amplifiers in the 1990s helped bassists to use effects and perform more soloistic playing styles, which emphasize the higher range of the instrument.
In addition to choosing between laminate and solid wood, you also have to consider the type of the tonewood. Of particular importance is the choice of top wood, because it greatly affects the resulting sound. Spruce is popularly used for the tops of acoustics because of its punchy and bright tone. Mahogany tops on the other hand is preferred for its warm tone, with more emphasis on the lower mid frequencies. There are other types of wood that fall between the two, each one bringing a subtly different flavor to the resulting sound.
{"product":{"id":"113900398","stock":"instock","price":"179.99","name":"Vintage 1960s Decca DM1-204 Natural Acoustic Guitar","download":false,"sku_id":"113900398","checksum":"134135816000","rep_id":"site5113900398","displayId":"113900398","sku_display_id":"113900398","sku_rep_id":"site5113900398","gc_pro":false},"category":"Acoustic Guitars","pageName":"product_detail","subcategory":"6 String Acoustic Guitars","dept":"Guitars"}
This deal leapt out of the page at me straight away. The Fender Squier series has been around a while and even though it’s a budget guitar, you can always rely on Fender for great quality. But what I like the most about this package is that everything you need is included (apart from a guitar stand) and the Frontman 10G amplifier has some extra features that are excellent. The amp has an input for a playback device to jam along to (like your iPad or Smart phone, or even a CD player) plus a headphone output for when the neighbours get too annoyed. A Gain control and Overdrive switch let you grunge everything up, or you can dial it back to a classic, clean Fender sound.

Ibanez JEM77WDP Electric Guitar With the Ibanez JEM77WDP Steve Vai Signature guitar, you can get a little piece of the legendary guitarist. This model is also commonly referred to as the JEM Woody because of its distinctive poplar burl veneer pickguard and matching headstock. Part of the company’s Premium line, the JEM77WDP electric guitar also features two cutaways and Steve Vai’s signature monkey grip.
For his work on Supernatural, Glenn Kolotkin turned to elaborate multi-miking as a way of managing Carlos Santana's complicated setup. "I used multiple microphones on Carlos' guitars: Electrovoice RE20s close, Neumann U47s further away, an SM56, U87s. He was playing through an assortment of amplifiers at the same time, and by using multiple microphones I was able to get just the right blend."
when I started playing, if you wanted distortion, you "cranked up" the volume on the guitar and the amp. my old Gibson amp had reverb and tremolo. I used to play without reverb or tremolo. nowadays, in my old age, I use a little reverb for flavoring. I have pedals, but it's too much hassle to set everything up. so, I just plug into the amp with a little reverb. I'm happy and that's all that really counts. isn't it ?
A Power attenuator enables a player to obtain power-tube distortion independently of listening volume. A power attenuator is a dummy load placed between the guitar amplifier's power tubes and the guitar speaker, or a power-supply based circuit to reduce the plate voltage on the power tubes. Examples of power attenuators are the Marshall PowerBrake and THD HotPlate.
While you're doing your strumming and picking lay that part of your hand on the strings by the bridge of your guitar. This will mute or partially silence the strings. On an electric guitar going through an amp, this can become a percussion instrument. The trick is to use it for a percussion effect and then raise that hand up when you want to let the strings rings er.. ring.
Look for lyrics or chord changes. Many songs have guitar parts made up solely (or mostly) of chords. This is especially true for rhythm guitar parts. In this case, the tab may forgo typical tab notation in favor of a simplified list of chord changes. These chords are almost always written in standard chord notation (Amin = A minor, E7 = E dominant 7, etc.) Simply play the chords in the order that they're listed - if it's not noted otherwise, try playing one chord per measure, but if the changes don't sound right, listen to the song for the strumming pattern.
To show you how to read the chords diagrams above, let's use the A chord as an example. For the purposes of chord diagrams, here is how your left-hand fingers are numbered. As you will notice, the index finger is denoted with number 1 the middle with 2 the ring finger with 3 and the pinky with 4. These numbers are used on the diagrams to show you what fingers use for pressing the frets composing the chords.
I found one at a local shop, 60's Norma, resembles a Strat LIKE guitar, but with a sweet design... It has two switch where you would fidn hte pickup selector on a gibson les paul. Its got a few nicks and such, but it sounds REALLY good and the guy only wants 60 bucks, I plan on buying it, re-fretting, and doing some custom fix up on the body. And He said pretty much everything is original... A pretty sweet guitar if you ask me... If and when I buy it I'll get a picture, email if interested!
Modulation stompboxes like our BF-3 Flanger should be after the tone-producing effects like distortion, wah, etc. so they can process and modify the tone built by the pedals before it. If you put it before the distortion, then you are distorting the sound of the flanger. Maybe that’s what you’re after, but in general, put the BF-3 and other modulation effects after the tone-shaping (and noise–producing) pedals. And then there are the ambience effects: delay and reverb. As we discussed earlier, reverb—and sometimes delay, depending on the space—is the last thing that happens before the sound reaches your ears in a physical space, so these go last. Delaying reverb can sound muddy, so it’s usually better to have the reverb after the delay.
I had just finished signing up for I am a 54-year-old disabled Miner of 22 years, so I thought I would try to take up playing the guitar once again like I did when I was a kid. I forgot a lot about it through the years as life moved on, but now all I have is time. I came across your website and thought why not give it a try. so anything you suggest I will try once twice if I like it lol

Here we have the very highly respected ... Alvarez Yairi dy91 ... This very unique and beautiful guitar is in AMAZING CONDITION and is based on the RARE exotic Hawaiian Koa tone wood and is one of more ornate & fancy D-45 Martin Drednaught Acoustic the Martin retails for well over $7,500 and this guitar offered here at JVGuitars is the Alvarez Yairi answer and is quite a HIGH END JAPANESE HAND CRAFTED GUITAR by one of the greatest Luthiers in Japan.... Reserve your Rare & Exotic Koa Yairi DY91 Today...this baby is in excellent vintage condition... This is THE DY91 to own... any questions please email me All the best! General specs:About the DY91: These High End Yairi acoustic guitars are Handcrafted for outstanding projection, this example offers enhanced bass response and an articulate high-end register performance. As with this one many are Sculpted from some of the most precious rare sought-after tone woods from all over the world. This example is Hawaiian WoW! Here are the Specs: Handmade in Japan Saddle & Nut: Bone Neck Joint: Hand Fit Dovetail Finish: Gloss Body Style: D-45 Style Slope Shoulder Dreadnought Back & Sides: AAAA Figured Koa Top: Solid German Spruce Neck: Premium grade Mahogany Fingerboard: Bound Ebony Scale: 25 3/8" (645mm) Width at Nut: 1 11/16" Fingerboard Inlay: Large Diamond Bridge: Ebony-Inlaid Body Binding: Ivory & Abalone Soundhole Rosette: Abalone Head Overlay: Figured Koa Pickguard: Black Tuning Machines: Original Yairi Gold Die Cast Finish:Gloss Natural Electronics: None Original Semi-hard shell case: Case candy Included .

What can we learn from these restaurant guests? The lesson is that we are very easily tricked into liking things we pay more for, even though they might not be that good after all. We get a particular feeling from thinking that we’re treating ourselves to something luxurious. If we, on the other hand, haven’t spent very much, we usually assume that it can’t be a good product.
Organ tones are sounded in one of three ways; in 'normal' mode, by pressing any string onto a fret; in 'percussion' mode, by fretting any string and touching the included brass plectrum (connected to a short wire plugged into a socket on the scratchplate) onto any metal part of the guitar; or by pressing one of the six 'open string' buttons. There is an option to silence the lowest two strings, and the organ section, as a whole, can also be switched off. There is a four-position octave selector, a six-position effect selector, a four-way selector for the percussion and a flute selector.
Although fairly small in size, this packs a serious punch thanks to the overdrive control which can produce that classic orange crunch to smooth and creamy British distortion. The Orange Crush 12 is definitely a great small gig and rehearsal amp, but it also makes a fantastic amplifier for practice at home thanks to the headphone/line output which features the Orange CabSim technology. This allows you to plug your headphones in and enjoy a faithfully emulated sound of a mic’d Orange 4×12" cabinet directly to your headphones – ideal for silent practice. This can also be used in conjunction with your audio interface for direct recording and the capturing of authentic Orange tones without dragging a massive cabinet into a room (or destroying your windows!).

So, I’m 50+, I’ve never played a guitar, and I’m trying to decide on an electric guitar. I’m less concerned with the brand name, more concerned with high quality and workmanship, and last, I like the tone of the guitars played by the late Pete Ham of Badfinger (especially Baby Blue), and Joe Walsh. I know Ham played a cherry red Gibson SG standard, but I’m seeing quite a few mixed reviews on the quality control and workmanship of the current SGs. I listen to a lot of jam band music (i.e. Widespread Panic) and enjoy the rhythm guitar best. So, where to start and stay under $2000 to get a guitar that will produce the type of sound I’m looking for?
In the early 1950s, pioneering rock guitarist Willie Johnson of Howlin' Wolf′s band began deliberately increasing gain beyond its intended levels to produce "warm" distorted sounds.[3] Guitar Slim also experimented with distorted overtones, which can be heard in his hit electric blues song "The Things That I Used to Do" (1953).[8] Chuck Berry's 1955 classic "Maybellene" features a guitar solo with warm overtones created by his small valve amplifier.[9] Pat Hare produced heavily distorted power chords on his electric guitar for records such as James Cotton's "Cotton Crop Blues" (1954) as well as his own "I'm Gonna Murder My Baby" (1954), creating "a grittier, nastier, more ferocious electric guitar sound,"[10] accomplished by turning the volume knob on his amplifier "all the way to the right until the speaker was screaming."[11]
Judging by many of my last few years guitar purchases (on Ebay and elsewhere), I’m the kind of a person who seems to think he’s the kind of a person who likes guitars with a lot of knobs and switches. I’ve bought several multi-pickup guitars. Old ones, new ones, new ones made to look like old ones (not those stupid “relic-ed” ones, though…I’m an idiot, but I’m not stupid). Yet, as I look at the keepers in my collection, I’ve only kept one guitar with more than four knobs, and none with more than two pickups. Odd.
This is the name given to the amplifier, separate from the speakers. It’s the pre-amp and amp in one box, which is usually placed on top of a cabinet or a stack of speakers. This is a common configuration for large venues, and it might be useful to have a separate amp head if you play a lot of festivals or “battle of the bands” events, where the speakers are generally provided by the organizer.
The Ibanez Artcore AF75, PRS SE Standard 24 and Schecter PT, for example, are priced below $600 and have been highly rated. They’re not exactly cheap money-wise, but they’re definitely worth a lot more. Getting one of those from the get-go will make playing guitar a lifetime passion. “Cheap” guitars may seem more affordable at first, but many of these are poorly made and can be more costly in the long run because of constant repairs and replacements.
Chords in a song are arranged according to chord progressions, which are chord intervals that work pretty much the same as single notes in a scale. It’s very important for you to learn chord progressions for the various keys, because then, as long as you know what key the song is in, you can figure out the chords in it very easily. There may be times when you want to change the key of a song to one you can sing or play in better, and for this, knowledge of chord professions is critical.
If you are feeling lucky, you can purchase any one of these guitars online. I personally like to sit in a store and play the actual guitar I’ll be taking home. That way I can see if the action is set too high, how it feels, and most importantly how it sounds. You can without a doubt find a great acoustic guitar for under $500. Don’t rule out the option of buying used. You can find a guitar that retails for $900 for maybe $500 used on sites like or
For more control and fine tuning of your sound, you may want to use a parametric or graphic EQ. A parametric EQ allows you to adjust the width of the frequency band that's being altered and the shape of the curve—how abruptly the boosted or cut area changes to the unmodified area. A graphic EQ divides the frequency ranges into a number of narrow bands which can each be boosted or lowered by sliders, thus giving you a visual or "graphic" representation of how the EQ is being affected. The more bands there are, the more precise your adjustments can be.
Even cheaper (abour $40) is the Behringer Guitar Link (review: Behringer Guitar Link UCG102 USB Interface Review). One nice thing is the long cord.. you can sit a ways away from your PC without needing an extender, and like the line 6, it’s also got a headphone output. They offer some guitar effects software as well, via download, and a basic DAW program. Worth checking out, as this does check every basic box for forty bucks. I have not used this, but I have used other Behringer audio interfaces. Cheap, basic, but they do include ASIO drivers (read ahead).
: : "Later, in the '70s, a line of low-priced Japanese-made instruments were imported and sold under the Dorado name in an effort to compete with the flood of imports inundating the market. Flattop acoustics and solidbody electrics alike were sold under the Dorado name. None hold much in common with Gretsch's own guitars." Also, that Gretsch had been sold to Baldwin prior to 70's; reacquired

After the lawsuit Hoshino Gakki abandoned the strategy of copying "classic" USA electric guitar designs and moved to the popular superstrat era in the mid-1980s. The newer Ibanez models began incorporating more modern elements into their design such as radical body shapes, slimmer necks, 2-octave fingerboards, slim pointed headstocks, higher-output electronics, humbucker/single-coil/humbucker pickups, locking tremolo bridges and different finishes.
And just a quick note: I do not buy or sell guitars. I have no idea what any given guitar from this period would sell for. I don't know if some of the listed guitars are indeed valuable. My sole purpose is to help people looking specifically for information on the maker of their MIJ guitar. So please...don't ask me what your guitar is worth. To me, they're all priceless.
1967-1969: about the coolest guitar Danelectro ever produced. Has 13 drone strings that move from the vibration of the usual 6 strings. Three pickups, 2 for the 6 stings and 1 for the drone strings. Crinkle burgundy finish, 3 point body shape. Has a "buzz" bridge which similate the sitar sound. The resonation from the buzz bridge vibrates the top of the body and the drone strings. Clear pickguards protecting the drone strings and Vinnie's name on the lower 6 string clear pickguard. Body is made entirely from Poplar, with a semi-hollow construction.

Yeah, I wasn't meaning to disparage either brand. While not necessarily "cool", they both offer solid stuff and a really good value that really competes with luxury brands. I'm not a car guy, so I'll stay on the guitar side for an example - Schecter can offer a mahogany body with a flame maple top and binding, set neck, ebony fretboard with abalone inlays, 25.5" scale, compound radius, original Floyd, and name brand pickups for $1000, give or take. Seems like you have to get up into Ibanez's Prestige line or the Jackson USA line to get all that, and then you're paying around $2k.
Of course the most talented and creative guitarist in the World. Guitarists like Slash can give stunts but cannot be such creative like Gilmour. I don't know why people cannot understand and like silly stunts rather than real talent. A layman can listen to the guitar solos of Echoes, Dogs, Coming BAck to Life, Comfortably Numb, Time... Of Pink Floyd and they will easily know his vast talent. Gilmour must be ranked higher.
The previously discussed I-IV-V chord progressions of major triads is a subsequence of the circle progression, which ascends by perfect fourths and descends by perfect fifths: Perfect fifths and perfect fourths are inverse intervals, because one reaches the same pitch class by either ascending by a perfect fourth (five semitones) or descending by a perfect fifth (seven semitones). For example, the jazz standard Autumn Leaves contains the iv7-VII7-VIM7-iiø7-i circle-of-fifths chord-progression;[80] its sevenths occur in the tertian harmonization in sevenths of the minor scale.[81] Other subsequences of the fifths-circle chord-progression are used in music. In particular, the ii-V-I progression is the most important chord progression in jazz music.
yea, i’ve looked on a lot of websites. The way the 5-way switch is explained here helps a lot. Actually, the Dimarzio site has the closest wiring schematic that I’ve seen. I tried it and I got 2 out of the 5 positions to work. The problem is that all 3 pickups are running on both the working settings, just the bridge is more defined on the one setting and the neck is more defined on the other.
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: vox","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"category","prop11":"electric guitars","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] sub category"}
pay is about HALF of what it should be for this expensive of a product, when a factory is turning out nearly $1 million a week in profits from one factory with less than 50 employees, they should make more than the salary cap of $12-$15 per hr, the only reason you make a decent living wage is because you work so much you don't have any time to live. You may have time to go home and sleep (and eat something, if you're VERY lucky, most days i don't even have the energy to wake up and eat once i get home.
Second, you might be wondering if it’s just better to get a cinematic VST or one that takes from a range of instruments. Fractured does have cymbals and bass kicks but, of course, the guitar creates these and this gives them a lot of offbeat character. You could easily get a more rich and deep bass kick with a drum VST, but then you lose that quirkiness that propels and highlights Fractured.  

1960's Teisco Del Rey, Model ET-44? Electric Guitar. 4 single coil Pickups. Great, original Black / Green burst finish. '57 Chevy style aluminum pick guard. "Shark-Fin" headstock. Rosewood fingerboard. Original 4+2 tuners with cast cover. 4-bolt neck joint with an adjustable truss rod. Bridge adjustable for height, intonation and string spacing. 4-Square pole pickups, 4 pots, 4 pickup selectors and a 3 position rotary wafer switch. Some of the pots do things and some don't either by modification or design. The rotary switch simply acts as an On / Off switch. Guitar works great the way it is, or could be configured other ways as well. We have not modified it since we acquired it 8 years ago. It's spent most of it's time in the box, until I decided to get around to listing it. Missing whammy bar as are most every Teisco we have ever owned. The bridge pickup has had one of it's mounting screws changed. The finish is in exceptional shape for a 40 year old guitar (while the photos make the guitar look black the finish is actually a dark green to black burst). Plays and sounds great. Not many finish chips. Very shiny. Frets in near new shape with virtually no wear. We have completely done a "Pro" set up on the guitar, including cleaning all the electronics, oiling the fingerboard, nut checked for correct height, neck angle checked, pickup heights checked and adjusted, adjusting the neck and action for great playability (clearance at the 9th fret = .008 when fretted at the first and the body (super low)) adjusting / checking the intonation (adjusted perfectly!) and cleaning and polishing entire instrument. This is our old shops standard $75 tune-up. Plays and sounds great. We also installed a new set of .009 strings. No case included.

You might recognise this in the tone knob above. The only difference is that R11 is a variable resitance from 0 to 250 Kohm, and C4 is a fixed value. Several guitars have several combinations of R11 and and C4 to achieve different cut-off points. When R11 is 100% position, the resistance is maximised, so there is little incentive for eelctrical current to flow to C4. The signal is not affected as much.

Fortunately, some of the best happy accidents have been preserved for posterity. For over 40 years Seymour W. Duncan has kept meticulous notes on the best pickups to cross his workbench. Many of these have been resurrected as Seymour Duncan models. For example, our ’59 Model is based on a particularly sweet-sounding ’59 P.A.F. in one of Jeff Beck’s guitars. Another of our models, the Pearly Gates, is inspired by another, rawer-sounding ’59 P.A.F. That’s just one example of two supposedly identical pickups from the same year displaying different musical personalities.
At the core of this pedal is the Line 6 HX technology, which emulates the behavior of actual amp and stompbox components. This means that instead of merely copying the sound, it recreates the entire pedal or amplifier in digital format, allowing the models to respond to guitar tone and adjustments much like the real thing. While it originally had 70 effects, firmware updates have raised this number to 104, which is more than enough to keep you busy for months, if not years. Amp, cab and mic models were also increased to 115. Since Line 6 is well known for providing updates, it is reasonable to expect more expansions in the future. It does everything that the Helix LT can, with some extras, most notable of which is the LED scribble strips for labeling each footswitch. The Helix Floor also comes with expanded input/output options to work with mics and other instruments. respects the intellectual rights and property of the owners, luthiers and salespeople at the Rickenbacker, Gretsch, Gibson and Fender Guitar Corporations. Registered trademarks/designs of these corporations include, but are not limited to, 325, 330, 360, Jetglo, Stratocaster, Flying V. is not affiliated with these corporations in any way. The guitars above represent instruments built in Japan for the Japanese domestic market only. They are no longer being made or distributed, which makes them rare. This page was created for collectors and enthusiasts; for the sole purpose of providing information, photo documentation and research tools.
Instrument amplifiers are available in a wide range of price, quality, and performance levels. Some are designed for beginners, such as small, low-wattage practice amps, which typically have a single 8" speaker and about 10 watts, or smaller "combo" amps with relatively low wattage (15 to 20 watts) and a single 10" speaker. Mid- to large-size "combo" amps with 30 to 50 watts and one 12" speaker or four 10" speakers are best for high-volume situations, such as band rehearsals and onstage performances. For large venues, such as outdoor music festivals, guitarists may use one or more 100 watt (or several hundred watt) heads with one or more 8x10” cabinets. Some guitar amps are strongly associated with specific instruments or genres, such as the Marshall amps, which are widely used in heavy metal music.
On the other hand, if you know that you have spent a decent amount of money on something, you’re more likely to keep using it, so that you didn’t pay that much in vain. Getting a proper guitar from the start also means that you don’t have to get another one as soon as you get a little bit better and start to notice that maybe your $50 guitar wasn’t that amazing after all.
A Delay or Echo pedal creates a copy of an incoming sound and slightly time-delays it, creating either a "slap" (single repetition) or an echo (multiple repetitions) effect. Delay pedals may use either analog or digital technology. Analog delays often are less flexible and not as "perfect" sounding as digital delays, but some guitarists argue that analog effects produce "warmer" tones. Early delay devices actually used magnetic tape to produce the time delay effect. U2's guitarist, The Edge, is known for his extensive use of delay effects. Some common Delay pedals are:
Guitar Neck wood Fingerboard Blanks Electric guitar wood Burl Poplar 1pc Walnut Spalted Apple Burl poplar Spalted Maple Olive Spalted Walnut Burl Elm African Mahogany body wood Red Willow 1pc body blanks Plum Red Willow 2pc body blanks Spalted Birch Pear Mulberry Maple Acoustic / Classic guitar wood Flute and Oud blanks Pool Cue wood blanks & Wood Turning Gallery Sold examples Custom Wood Products Binding wood NEW! Gun Stock Blanks
This is because sound in an acoustic is dependent upon the bridge, saddle, and soundboard’s (top) ability to transfer string vibration through the sound hole of the body. The top (soundboard), back, and sides makes the body of the guitar where the sound hole is designed and cut. Knowing this, you’ll not only need wood that’s strong, but wood that can offer unique acoustic properties that emphasize its ability to project differing sounds at various frequencies. Of course, your choice of strings also lends to the harmonic ranges of a guitar.
For those players who prefer the good old valve sound and searching for one on a reasonable price, the VOX AC10 can be that great choice of an amplifier for the job. This 10 watts amp with 1×10” inch celestion speaker has a 2x12AX7 tube preamp section and 2xEL84 valve reactor power section housed in a closed back cabinet and its trademark grill cloth to deliver a genuine VOX brown sound. 
OK, when the list started it was hard to tell if the author was knowledgeable on the subject because of the automatic “Go To” names. Unfortunately, by the time I got to the end I realized this was the author’s favorites list versus the Top 10 Greatest Guitar Players. Kirk Hammett, Slash, Jack White, Chuck Berry??? You can’t put them on any list and not mention the guy who influenced so many, and who Eric Clapton called the best guitarist in the world, SRV. Richards biggest claim to fame it the amount of drugs he’s done that haven’t killed him,… Read more »
When Electric Mud was released, it was a huge success, selling 150,000 in the first six weeks. It was also the best selling Muddy Waters record at Chess ever, entering Billboard's Top 200 Chart. It was a triumph of a record that updated his sound and put him elbow to elbow with the bands that had influenced him. The record broke down restrictions of genres with its inventiveness and ability to re-arrange songs and have them come out as something radically different. Unfortunately, narrow-minded blues purists across the board denounced it as atrocious, offensive and a big "sell out." There's a direct similarity between this and what happened to Bob Dylan a few years earlier when he decided to go electric, making his folk-purist fans angry that he was "selling out" to rock and roll. Since Muddy is primarily a blues artist, overviews of his career would be written by a number of blues historians who would automatically dismiss this record for years to come.
In 1954 Pat Hare produced heavily distorted power chords for several recordings (including James Cotton's Cotton Crop Blues"), creating "a grittier, nastier, more ferocious electric guitar sound,"[36] accomplished by turning the volume knob on his amplifier "all the way to the right until the speaker was screaming."[37] Link Wray's 1958 recording "Rumble" inspired young musicians such as Pete Townshend of The Who, Jimmy Page of Led Zeppelin, Jeff Beck, Dave Davies of The Kinks, and Neil Young to explore distortion by various means.[38] In 1966, the British company Marshall Amplification began producing the Marshall 1963, a guitar amplifier capable of producing the distorted "crunch" that rock musicians were starting to seek.[39][40]
Ah yes, the 808. It's often used and referred to as a kick, but it tends to act more as a very low tom, as it has a pitch. This thing is the Loch Ness Monster – there tends to be more under the water. The best way to deal with a true, clean 808 sample is to work around it. It's usually best to let the 808 do its thing and to get the bottom end around it the hell out of the way. If it's a fuzzy sample or has been driven and squashed, you may need to play with things above 250 Hz, but usually live and let live is the best approach.

Vintage Gibson Les Paul Special model, introduced in 1955 This 1957 model is killer.Utilizing the Junior’s solid Mahogany body with single cutaway shape but  finished in what Gibson called Limed Mahogany which appeared white on black and white television sets which gives it the nickname of "TV Special"A neck pickup with accompanying volume and tone circuitry was also added making the Special an affordable but still professionally playable instrument. The Special was sold in this configuration until 1958 . Gibson’s surviving shipping records indicate approx. 1,452 Les Paul Specials were shipped in 1957. MORE HERE.
When used with the human voice, it is important that the pitch correction doesn't happen too quickly, otherwise all the natural slurs and vibrato will be stripped out leaving you with a very unnatural and robotic vocal sound. If only a few notes need fixing, consider automating the pitch-corrector's correction speed parameter so that it is normally too slow to have any significant effect, then increase the speed just for the problem sections. This prevents perfectly good audio from being processed unnecessarily.
Ooooohhhhh.... I used the Firebird 12 for two weeks on sessions in 1973.... I STILL solo the tracks I used that on... it's the BEST BEST BEST BEST OF ALL TIME !!!!!!!! FOR ANYTHING !!!!..... in fact, as I remember, the octave strings were wound different than the way Ric does it (high-low) and that even added to the incredible sound.....wanna sell the Firebird 12?
Maintaining these items does help though, perhaps every year or so remove the cover plate or pickguard and clean out any dust building up on the switch and contacts, it'll make them last for years to come so it's worth the minimal effort. You'd perhaps clean the fretboard and frets, so it's worth thinking about the other, hidden, functional parts too. is a curated collection of electric guitars chosen for their unique tone, design, and significance in electric guitar history from approximately 1950-1980. This collection approaches electric guitars from the underdog perspective. So we carry guitars built for the masses, luthiers & manufacturers who pushed the boundaries as to what was possible in terms of not only instrument quality but tone. Design also plays an important consideration in this collection. Alternative materials, innovative tuning systems, and high quality-low cost manufacturing processes are only some of the unique qualities found on instruments at

My services include re-frets, fret dressing, fret end dressing, action adjustment, truss rod adjustment, intonation setting, nut replacement, bridge saddle replacement, acoustic pickup installation, electric pickup fitting/replacement, output jack replacement, pot replacement, re-wiring, sound post setting, tuner installation, brace re-gluing, broken headstock repairs, strap pin installation, re-strings, bridge setting, tremolo setting, Floyd Rose setting, custom scratch plate cutting, tuning problems, restoration, polishing, cleaning, wiring modifications...Get in touch I'm sure I can help!

Second in your chain are usually wah or EQ pedals. These tend to do well when directly affecting a distorted signal, and without much else in the mix. If you plan on using a compressor you have a choice: for a more natural rock tone, the compressor works best right after the distortion or wah/EQ effects. If you’re going for that thick classic country sound however, try putting your compressor right at the end of the chain so that it squashes everything.
Subsequent years brought new company ownership to the Gibson Guitar Company. During the “Norlin Era“, Gibson Les Paul body designs were greatly altered, most notably, the change to the neck volute. Because the Les Paul had the reputation of having an easily broken neck joint, the volute strengthened the neck where it joined the headstock to avert breakage. To further increase the strength, the neck woods were changed from mahogany to a three-piece maple design. The LP body was changed from a one-piece mahogany with a maple top into multiple slabs of mahogany with multiple pieced maple tops. This is referred to as “multipiece” construction, and sometimes incorrectly referred to as a “pancake” body. The expression “pancake body” actually refers to a body made of a thin layer of maple sandwiched between two slabs of mahogany, with a maple cap. The grain of the maple was placed at 90 degrees to that of the mahogany. The “pancake”-like layers are clearly visible when looking at the edge of the guitar. This process is also known as “crossbanding”, and was done for strength and resistance to cupping/warping. Crossbanding was phased out by 1977.
The Vox Show Room shows the classic amps behind the British Explosion of sound in the 60's. VOX, at one time was one of the largest musical instrument producers in the world and their products were utilized by almost every major music group during the nineteen sixties. From The Shadows to The Beatles to U2, VOX is the "voice" of generations of musicians worldwide.
Ovation’s Lyracord backs weren’t the company’s only fling with synthetic materials. In the early ’70s Charles Kaman set his engineers, many of whom were not guitar players, to work on developing a new synthetic guitar, yielding the deep-bowl, acoustic-electric Adamas which went into production in 1976. The Adamas top, called a Fibronic Soundboard, was made of a laminate of carbon-graphite and birch about a third the thickness of a conventional spruce top. Instead of a regular round central soundhole, Kaman engineers positioned 22 smaller holes on the upper shoulders surrounded by epaulets of multicolored woods in a kind of leaf design. The bridges and headstock featured elaborate scroll carving. The neck was reinforced with a patented Kaman bar, a u-shaped cast aluminum insert designed to keep the neck stable even with dramatic changes in temperature and climate. The necks and fingerboards were made of walnut. The fingerboards had hollow triangular maple inlays, tapered beginning at the 18th fret on the bass side to the 24th fret on the treble. Hardware was gold. Until the advent of Ovation’s Collector Series in 1982, the Adamas was Ovation’s flagship, favored by the likes of Larry Coryell and others.

Second, you might be wondering if it’s just better to get a cinematic VST or one that takes from a range of instruments. Fractured does have cymbals and bass kicks but, of course, the guitar creates these and this gives them a lot of offbeat character. You could easily get a more rich and deep bass kick with a drum VST, but then you lose that quirkiness that propels and highlights Fractured.  

Tablature, or Tab, is a very important tool that allows guitar players to easily learn how to play chords, melodies, and songs. Learning how to read guitar Tab can be a mystery for some newer guitar players. In this guitar lesson, we are going to learn how to read guitar Tabs and go over some of the more common elements you will see when you pull up a Tab for a song you want to learn. Try this lesson if you want to learn how to read guitar sheet music.

Finally, there were some twelve Hawaiian lap steels in ’55, the EG-NT, EG-K, EG-Z, EG-A, EG-S, EG-R, EG-L, EG-7L, EG-P, EG-8L, EG-M and EG-NW. Again, since I have no reference materials, there’s no point in attempting any description. However, many of these guitars continued on into the ’60s where we’ll discuss them in detail, and you can probably extrapolate backwards to these mid-’50s models, allowing for pickup changes, etc.
Add bite or presence by boosting between 2kHz and 6kHz, depending on the tone you're after. Little over 4-5kHz is produced by a guitar speaker, though going for a brighter DI'd clean sound is quite legitimate for artistic reasons. Similar-sounding electric guitars that may be conflicting within a mix can be separated to a limited extent by adding bite at different frequencies, though choosing two different-sounding guitars and/or amp sounds and examining the arrangement carefully usually works better. As a rule, single-coil guitars are best for cutting through a busy mix without taking up too much space, while humbucking pickups create a thicker sound which may be beneficial in recordings where there is only one guitar part.
In general, this measurement is taken by measuring the distance between the bottom of the string and the top of the 6th fret while holding the string down at the 12th fret and the first fret. This is where the capo comes in handy - put it on the first fret so your hand is free to take the measurement. Using a feeler gauge of the desired height, in this example, 0.010, hold the low E string down at the 12th fret (with the capo on the first fret), and measure the distance between the top of the 6th fret and the bottom of the low E string. If the distance is greater than the desired relief, then you need to turn the truss rod clockwise (towards your right) as you're looking down the headstock towards the body of the guitar. If the distance is less than the desired amount, then you need to turn the truss rod counter-clockwise (towards your left) as you're looking down the headstock towards the body of the guitar. The basic rule is:
Conversely, buyers can use these websites to find out what the real value of a guitar is. This can be useful whether you're buying from a private seller or the guitar store down the street. Don't be afraid to haggle if the seller wants more than the guitar is actually worth according to book value. While the seller may eventually find another buyer, there's no reason for you to over pay.
{"eVar4":"vintage: guitars","pageName":"[gc] vintage: guitars: supro","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop2":"[gc] vintage: guitars","prop1":"[gc] vintage: guitars","evar51":"default: united states","prop10":"brands","prop11":"supro","prop5":"[gc] vintage: guitars","prop6":"[gc] vintage: guitars","prop3":"[gc] vintage: guitars","prop4":"[gc] vintage: guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,","prop7":"[gc] vintage"}

We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. If you want to become a real guitar hero, you'll need the right ax. Our selection of electric guitars includes something for everyone, from simple, inexpensive options best suited for beginners to top-tier models coveted by amateur and professional musicians alike. We've ranked them all here by playability, tonal range, durability, and style. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best electric guitar on Amazon.
A significant cosmetic change occurred in Japan in ’65, which can help determine dates. Previously, almost all models had plastic pickguards. In ’65, most models switched to striped metal guards, with the alternating matte stripes etched into the metal. Thus, if you find a guitar Teisco with a plastic guard, it’s probably from ’64 or early ’65. If it has a striped metal guard, it’s probably from ’65 or later.
The best way of working out which contact is which is to use a multimeter and see for yourself which contacts are connected to each other in the 5 switch positions. On the Fender-type and some import-type switches you’re given a good clue because you can actually see the mechanism or see through the switch casing. Watch this as you move the switch through the 5 positions – you can see which contact is always in circuit (the wiper) and which ones are in circuit in each position (1, 2, 3, 4 and 5). This method of visualising the switch also helps when it comes to fitting the switch to your pickguard and getting it the right way around! Now, where does the wire from the bridge pickup go again…
I played electric guitar in a band from the age of 12 through to the age of 36, then gave it up. Now, at the age of 68 I want to get back into playing. I went into a store and tried playing and found that my fingertips really hurt! Are there any electric guitars where the metal strings don’t hurt or do I just need to “grin and bare it” until my fingertips get calloused again?
Martin ukuleles produced in greatest numbers in the smallest soprano size, but concert and tenor sizes were available circa 1922. Concert and tenor models were available in all the following styles, with the exception of Style 0, which was produced only as a soprano. Custom order ukuleles, while rare, were available upon request, and may have combined features from various styles.

Fender had an electronics repair shop called Fender’s Radio Service where he first repaired, then designed, amplifiers and electromagnetic pickups for musicians—chiefly players of electric semi-acoustic guitars, electric Hawaiian (lap steel) guitars, and mandolins. Players had been ‘wiring up’ their instruments in search of greater volume and projection since the late 1920s, and electric semi-acoustics (such as theGibson ES-150) had long been widely available. Tone had never, until then, been the primary reason for a guitarist to go electric, but in 1943, when Fender and his partner, Clayton Orr “Doc” Kauffman, built a crude wooden guitar as a pickup test rig, local country players started asking to borrow it for gigs. It sounded shiny and sustaining. Fender got curious, and in 1949, when it was long understood that solid construction offered great advantages in electric instruments, but before any commercial solidbody Spanish guitars had caught on (the small Audiovox company apparently offered a modern, solidbody electric guitar as early as the mid-1930s), he built a better prototype.
So the actual vibrating length of the string should be the same in all cases, and if that's all that affects the magnetic field then none of the other things mentioned above should affect that signal. Do a simple test protocol such as plucking each string with the identical pick, record the waveform, overlay them and look for differences in the waveform.
Ibanez started off as a Japanese music company particularly focused towards producing copies of favorite guitars in America. Today, they have surpassed most firms by offering best quality products on their own. Being specifically directed towards the hard rock and metal players, Ibanez ensures to have something for players belonging to every genre.
This electric guitar style has experienced surges and lulls in its popularity, but has never fallen off the scene, due to the number of great players who have chosen to use the Flying V, such as Jimi Hendrix, Dave Mustaine, Kirk Hammett and Michael Schenker.  The Flying V offered many of the same benefits as the SG with a much more distinctive body shape.  It is now a very common guitar among heavy rock and metal guitarists and will achieve its destiny of being a guitar of the future!
We’ll round this list off with a slightly different proposition, particularly with jazz in mind. The Fender Classic Series ’72 Telecaster Thinline is a semi-hollow guitar in the guise of a traditional solid body. It features the same body shape and size of a standard Telecaster but has its horizon’s broadened thanks to the internal routing of the wood and attractive ‘f’ hole on the guitar’s top. Two humbuckers – again, not traditional on a Tele – provide exceptional warmth and versatility. Combined with its high levels of construction and craftsmanship this a guitar which will last a lifetime.
C.F. Martin & Company is a U.S. guitar manufacturer established in 1833 byChristian Frederick Martin. Martin is highly regarded for its steel-string guitarsand is a leading mass-manufacturer of flattop acoustics. Martin instruments can cost thousands of dollars and vintage instruments often cost six figures. The company has also made several models of electric guitars and electric basses.
Looking to connect with other fans of vintage gear? Join the community. Allow us to introduce you to the exclusive network of musicians and music lovers: Music Aficionado. This social network gives music enthusiasts a place to collect, share, listen to, and discuss everything they love about music from their favorite albums, playlists, and artists to their favorite pieces of gear, instructional videos, and altered tunings.

The Blackheart Killer Ant is another slightly unconventional choice. Features wise, the Killer Ant does not have even the basics found on most beginner amps, yet it costs more money. The only controls on the Killer Ant are a power switch and a volume control. However, what sets the Blackheart Killer Ant apart is the fact it is a tube amp, rather than the cheaper solid state amps used for most beginner amps.
Finally, amidst all the considerations about tops and shapes and tones, don't underestimate the importance of choosing a guitar that you like. Choose one that feels comfortable, whether you are sitting or standing. Make sure you pick a guitar that responds to the way that you play, and don't settle on a "good" guitar if you don't like the way it sounds to your ears.
The LGXT comes with 2 Seymour Duncan custom humbucker pickups that give it a classic electric guitar sound. The piezo pickup with custom preamp EQ makes it sound very much like an acoustic guitar. With the built-in synth pickup you can get just about any sound you want via a Roland GR series synth. It has a silver leaf maple solid body with a figured maple top and a mahogany neck with a richlite fingerboard on top which Godin says makes the action even better when using a synth. It has a full 25.5" scale length and 1.6875" nut width.
EQ pedals do exactly what you would think.  They allow you to set the tone of your sound through equalization.  Just like on your radio, they can adjust the bass, mid, and treble frequencies of your tone.  Depending on the type of EQ stompbox you have, you may have different ways of tailoring your tone.  There are two main types: graphic and parametric.
In the end I decided to go with the .033μ. Everything larger sounded too wooly to me on the neck pickup. If I didn’t play much EBow, I might even consider the .022μ. But you might make a different choice, especially if you were using brighter pickups. You won’t know for sure till you try it out with your instrument, amp, and hands, but I hope this gives you some idea of what to expect.
With this new edition, they scrapped the DVD from the previous version, and introduced online video and audio clips, as a supplement to the book's teachings. They didn't take it overboard though, with just 85 videos and 95 audio tracks, but at least it's a step in the right direction. You can't learn music by just reading about it, you need audible tools.
Custom 24 series have been the bread and butter of PRS for a long time. This guitar has proven to be a really capable axe that can keep up with you no matter where you go in terms of music. A good friend of mine used to own one for a long time, which allowed me to play it numerous times. It’s one of the smoothest and best sounding guitars I’ve ever had a chance to play.
Bass amp speaker cabinets are typically more rigidly constructed, with thicker wood and more heavy bracing than those for non-bass amplification. They usually include tuned bass reflex ports or vents cut into the cabinet, for increased efficiency at low frequencies and improved bass sound. Preamplifier sections have equalization controls that are designed for the deeper frequency range of bass instruments, which extend down to 41 Hz or below. Bass amplifiers are more likely to be designed with heat sinks and/or cooling fans than regular guitar amplifiers, due to the high power demands of bass amplification. They are also more commonly equipped with audio compression or limiter circuitry to prevent overloading the power amplifier and to protect the speakers from damage due to unintended clipping in the power amp.
Our guide to guitar strings, the hope and savior of beginners across the world. We're going to cover the types of guitar strings, how they're made, the best brands, the standard gauges, how to pick the right ones for your instrument and style, what to expect in terms of cost, and much more. Take a ride with me through Ledger Note's guitar string guide...

Processing audio before it passes through an amp simulator is a creative alternative to adding effects to its output. As described elsewhere in this article, pitch-shifting can work well in conjunction with amp simulation, but other ways of editing and processing the raw guitar file before it goes through the amp modeller also yield interesting results. Reverse reverb, resonation, vocoding and Auto-Tune can all produce distinctive effects. Try chopping small sections of guitar out, for an interesting stuttering effect that's nothing like tremolo. A piece of guitar that's been reversed before being fed through an amp modeller sounds quite different to what you get by reversing a guitar part that's already been through an amp, and this technique can be very effective. Likewise, recording three or four separate tracks of single guitar notes and routing them simultaneously through the same guitar amp simulator sounds very different from playing chords. Sam Inglis
The ’37 Hawaiian Guitar in both the Sorkin and Grossman books was basically the same squarish, pear-shaped guitar as in ’36, sans pickguard. It had a polished Ebonoid fingerboard with new parallelogram position markers replacing the old dots. Also, the large, two-part rectangular pickup cover/tail assembly was replaced with a more conventional, modern design. The pickup cover was the new rectangular type with the two pole extensions exposed. Off to the side of its surround was a little square plate on the treble side containing the volume control. The strings attached to a small piece of slotted metal hidden under a rectangular cover or “handrest.” Gone were the control wings. The microphone attachment stuck out the bass side of the guitar. The cost was $35, plus $6 for a case.
The Hummingbird Pro's unique look breaks the typical monotonous appearance of conventional acoustics, and it does so without straying too far from the familiar. It is easily identifiable by its uniquely shaped ornate pickguard, which matches the guitar's faded cherry sunburst finish. Whether you are on stage or just jamming with friends, you can be sure that this acoustic will stand out.
The 2019 Gibson Les Paul Standard sports a mahogany back with an artisan-grade AAA figured maple top and a mahogany neck with Ultra-Modern weight relief. This chambering technique is provides a solid core through the center of the guitar, retaining the classic Les Paul sound and making the guitar less prone to feedback. The Ultra Modern weight-relieved body also makes playing long sets a breeze. The neck has an asymmetrical Slim Taper neck profile for increased playability and comfort.
Now that we covered the basic features, let’s talk about what really counts: the built-in effects, amp models, and usability. For better or for worse, people tend to compare multi-effects units with the experience and sound you get from owning a pedalboard full of individual pedals. Well, great news: the consensus is that the Zoom G3X feels a lot like using individual stompboxes; more so than any other multi-effects unit on the market. Zoom really nailed it when it comes to making an intuitive interface. If you look at the layout, you’ll notice 3 “stompbox-style” sections side by side, each with a little display and on/off footswitch. These are meant to feel like 3 guitar pedals next to each other. They’re technically 3 slots which can each hold an effect or an amp model. The Zoom has 6 slots total (you can scroll left and right to access them), and all 6 can be used at once. You’ve got LOTS of choices to shape your tone: 94 effects and 22 amp and cabinet models. Any type of effect you can dream up, the Zoom G3X has you covered. Tremolo, vibrato, compressors, filters, overdrives are all available, and many of the effects simulate popular pedals like the Tube Screamer, EHX Big Muff, Pro Co RAT, Boss DS-1, and the list goes on and on. Same goes for the amp modeling - you can emulate a Marshall, Fender, Orange, Vox, etc. and pair up different amp models with various cabinet models. You can make your effect chain in whatever order you want, which is great for the beginner who is figuring out pedal order for the first time, and the veteran who wants to experiment with unique pedal combos. From a user review:

Power chords are one of the staples of rock music and one of the most important guitar chord types you need to have in your toolbox. They are important to learn for a few reasons: They’re easy to play They’re used a TON in many popular songs and are very versatile. They’ll help broaden your repertoire of guitar sounds / styles. This post will walk you through step-by-step what a power chord is, how to play them and what songs you can learn to start practicing them. What are Power Chords? Whether you play an acoustic or electric guitar, you are going
As to the “where,” positioning your mic an inch or less from the grillecloth and aiming it straight at the center of the speaker cone – pointing at the dust cap, in other words – yields a bright, punchy, detailed sound that suits many requirements, but can be too harsh. At the other extreme, aiming the mic at the edge of the cone, where the cone meets the suspension (the area just inside the speaker cutout in the cab’s mounting baffle) usually results in a looser, warmer, more raw and edgy tone. Between these two positions, there’s a wealth of voices to explore, and every inch of real estate that the mic covers between dust cap and cone edge will bring a noticeable sonic shift, without touching the amp’s controls. Also, aiming the mic straight at the speaker, in other words, mounted at 90 degrees to the flat plane of the front of the amp, and aiming it off axis, at a slight angle to the speaker, will illicit different sounds, too. With an assistant helping, or the guitarist playing if that’s not you, try moving the mic around the surface of the speaker while listening for the changes in tone through monitors or headphones, or if you don’t have enough isolation between live amp and monitors, record a little in each of several positions to listen back to. Pick the position you like for the track, and go with it.

For a novice like me, hitting those notes is no easy task. On my first brush with "Rocksmith 2014," I tackled Arctic Monkeys' "R U Mine?" This included a lot of missed notes and looking at my hands to find the right frets. But after playing the song a few times, it got easier and easier - even with the inclusion of more notes to master and more frets to find.
Lotus started with the elite league of Japanese craftsmen and initially made excellent Morris-branded guitars, but trying to keep up with the heavyweights such as Matsumoku Aria Pro II and Fuji-Gen Gakki Ibanez was difficult. Mismanagement and, especially, the inability to market their initial superb-quality guitars soon had Lotus' owners scrambling for cheaper labor, ending in India with poor quality and eventually no takers for their product, as Chinese and Indonesian guitar producers stepped up with instruments of comparable quality at similar prices.
Typical modern Telecasters (such as the American Standard version) incorporate several details different from the classic form. They typically feature 22 frets (rather than 21) and truss rod adjustment is made at the headstock end, rather than the body end, which had required removal of the neck on the original (the Custom Shop Bajo Sexto Baritone Tele was the only Telecaster featuring a two-octave 24-fret neck). The 3-saddle bridge of the original has been replaced with a 6-saddle version, allowing independent length and height adjustment for each string. The long saddle bridge screws allow a wide range of saddle bridge positions for intonation tuning. The stamped metal bridge plate has been replaced with a plain, flat plate, and the bridge grounding cover (which, while helping with the shielding, impedes players who like to mute strings at the bridge with the side of the palm, and makes it impossible to pick near the saddles to produce the characteristic Telecaster ‘twang’) has been discontinued for most models. Also different from the original is the wiring: The 3-way toggle switch selects neck pickup only in the first position, neck and bridge pickups together in the second position, and bridge pickup only in the third position. The first knob adjusts the master volume; the second is a master tone control affecting all the pickups.
Consider how many transformations take place during the production of sound from an electric guitar. The guitarist picks a string with a plastic plectrum, which produces vibrations that are picked up by coiled magnets directly positioned behind the strings, inducing an alternating current (hence the name “pick-ups”). The current’s signal is then transmitted through a wire lead, after which it’s amplified by either a vacuum tube or solid-state amplifier, and then reshaped into audible sound by a loudspeaker. Depending on the sound that a guitarist is seeking, he or she may place guitar effect pedals, or stompboxes, in between the pick-ups and the amplifiers. These small, intermediary devices further manipulate the guitar signal to produce a multitude of effects.
achieved by the creators. A lot of YouTube channels can be very amateurish and suffer from poor video quality, muffled audio and presenters who don’t work well with a camera. And it doesn’t matter if the lesson is coming from someone in the same room or from a studio on the other side of the world, the guitar teacher needs to be good. Someone who communicates clearly and makes you feel welcome.
REGOLAZIONE DELL'INTONAZIONE (FAT20) Per garantire l'assenza di movimento, ogni selletta è provvista di una vite di fissaggio. Per regolare l'intonazione, allentare la vite di fissaggio della selletta con una chiave a brugola da 2 mm (D). Per regolare l'intonazione, inserire una chiave a brugola da 2,5 mm nella vite della selletta sul retro del tremolo.
Small-diaphragm condenser mics, on the other hand, tend to have flatter frequency plots and a better-behaved off-axis response, giving a sound sometimes described as more focused, but they seem to be less commonly chosen by the interviewees than large-diaphragm ones. Neumann's KM84 seems to be the most regular choice of small-diaphragm condenser, and numbers John Fry and Bill Price amongst its high-profile users, while Sennheiser's MKH40 warrants a particular mention from Mike Hedges: "I started using [these mics] when I was working with the Beautiful South. I started off with two and now have more than 20. I think they were originally designed for classical recording, because they have very high gain and very low noise. This means that you can get a very clean sound. They also accept massive amounts of volume, so you can put one against a guitar amp on full and it will take it." Hedge's concern about the ability of the microphone to handle the sheer volume of some guitar amps is echoed by several of the other producers, who make a point of mentioning that they switch in a condenser's 10dB pad when recording electric guitars.
Russell is not only one of the hardest working technicians in Dallas but also a classically trained guitarist with a degree in classical guitar performance from SMU. To supplement his income playing classical guitar, he joined the Brook Mays team before finding a home at Charley's Guitar Shop. "Having a background as a player helps with cutting through the issue," he says. "I think the real part of guitar repair is being able to observe what's going on with the guitar but also understanding what the player is going through."
Prince at #10 just shows me that whoever made this list hasn't seen him play that often. And really, KR doesn't even need to be on the top 10. JH is way overrated, yes on the list, but NOT #1. But anyways, cool to see Prince even on the list. Those stupid people writing those comments are probably the ones that say "Prince plays guitar?" They are so living in a box!

Use of audio feedback to enhance sustain and change timbre. Feedback has become a striking characteristic of rock music, as electric guitar players such as Jeff Beck, Pete Townshend and Jimi Hendrix deliberately induced feedback by holding their guitars close to the amplifier. Lou Reed created his 1975 album Metal Machine Music entirely from loops of feedback played at various speeds. A good example of feedback can be heard on Jimi Hendrix's performance of "Can You See Me?" at the Monterey Pop Festival. The entire guitar solo was created using amplifier feedback.[26]