Although I’ve spent most of my life focusing on audio journalism, I’ve been active as a musician since taking up guitar seriously in the 1970s, and I have played lots of gigs with jazz, rock, and folk groups in New York and Los Angeles. I now play mostly double bass and ukulele; I currently play in three jazz groups in Los Angeles, and I sub regularly in a couple more groups. I also conduct more-or-less weekly jazz jam sessions at my home, where I accompany numerous guitarists of widely varying skill levels, toting all sorts of axes. Having conducted innumerable multi-listener comparisons of audio products over some 25 years, I have a good idea of how to make product tests fair.
Multi-effects units are exactly what the name implies—single units that offer many different effects and allow those effects to be used singly or in combinations simultaneously. Most will offer just about all the effect types discussed in this guide and many more. Typically they include dozens if not hundreds of effects presets—combinations of effects and effect parameters designed to achieve specific sounds with the touch of button or footswitch. Most also allow you to also save your presets for instant recall.

In the event it does not work out, the next measure is to utilize automotive fine grade sand paper to decontaminate contact points. Once more, cover this around a Q-tip for jack inputs and replicate the contact cleaner procedure. By now, you should have confirmed any likelihood that the problem is caused by a cleanliness issue. All your equipment should be fresh and clean for your upcoming performance.
As his Tuareg brethren continue their separatist insurgency in northern Mali, the leader of Tinariwen again can lay claim to being one of the world’s few literal rebel rockers. Ibrahim gets credit for inventing the modern Tuareg electric guitar style adopted by Etran Finatawa, Bombino, and other Saharan musicians. He generates this gritty, grungy, churning sound by hammering open strings on his Fender axe in a laid-back desert boogie reminiscent of his late northern Mali peer Ali Farka Touré.
Let’s kick things off with one of Schecter’s top tier models. Blackjack Slim Line C-1 FR is by far one of their more refined guitars. It’s slim, lightweight, and brings the kind of thunder that will give you goosebumps. With a set of premium Seymour Duncans, we expected nothing less. My brief encounter with this axe was one of the most enjoyable playing sessions I’ve ever had, and I’ve played many, many guitars.
Once you have a board design complete, you can send it out for manufacture. Years ago this used to be the major challenge for the home or small builder, but these days a large number of board manufacturers have a web presence and will quickly fabricate single, or low volume boards for fairly modest cost. Eagle (or whichever CAD software you are using) outputs a set of files called gerber files. These files can be emailed or uploaded over the web to the board manufacturer who will plug these into their manufacturing tools and then send the finished boards to you in the mail.
Ovation guitars have a history of innovative design, reflecting its founder’s engineering training and development of Kaman helicopters. Ovation guitars have composite synthetic bowls; earlier acoustic guitars have had wooden sides abutting a flat back since the 1700s. Kaman diagnosed structural weaknesses in the orthogonal joining of the sides, and felt that a composite material could be used for a smooth designed body. Ovation’s parabolic bowls dramatically reduced feed-back, allowing greater amplification of acoustic guitars. Improved synthetics used techniques from helicopter engineering to control vibrations in the bowl. Ovation has developed a thin neck, with the feel of an electric-guitar’s neck, but with additional strength from layers of mahogany and maple reinforced by a steel rod in an aluminum channel.[1] The composite materials and thin necks reduced the weight of Ovations.
Here we have a matching quad of late sixties Goodman speakers with green labels 25 Watts each @ 12 ohms Very rare in that EACH driver is fully functional, the cones are nice and stiff, no cone rub or any tears, just a killer set of vintage speakers. These came out of a wem cab and were also stock in laney cabinets(think sabbath tone, wem, Burman and Selmer gear Wem used odd impedances, these read 10.01 ohms on my multimeter so is treat them as 8ohms if they are wired up in a cab series parallel. Postage in the U.K. is £32 and they will be sent out in two separate parcels, you will have to arrange your own courier if your not U.K. based you can also collect in person! Any questions just ask
Side Note: The above is a visual example of how the wrong pedal order screws up your tone. When you compress before using delay, you get a perfectly shaped note ringing out and decaying uniformly over time. If you delay before compressing and even normalize with your make-up gain, you still lose volume and power due to the attack sneaking through first. Then your delayed notes are all also compressed, ruining your fine-tuned echo decay so that all echoes are relatively too loud and don't decay equally over time.
Route the body. You’ll need to make a cavity (a hole that goes partly through the body of the guitar) in the back of the guitar to fit the electronics for the volume, tone, pickup selection controls. You will cover it later with a bit of material (usually hard plastic). You’ll also need one cavity in the front of the guitar for each of its pickups. Rout the pickup cavity (or cavities) to the depth recommended by the manufacturer.[9]
Some bonehead really put the WRONG pickups in a guitar you just bought. So you bought a sweet vintage Strat from a guy who put P-Rails in it because now it can get "any tone".  He failed to mention that all of those tones kinda suck.  Hey, you just want a great sounding STRAT!  Drop in the right vintage Strat pickups and you'll be there baby'.  Then off-load those jack-of-all-trades tone-suckers to some idiot who actually believes one weird pickup can nail EVERYTHING.
Have you ever tried PRS acoustics before? They come with their SE line, and are fantastic quality guitars for the price. And their American acoustics are built by a small team of acoustic professionals. They only do "private stock" American acoustics now, but they used to have it as a regular lineup with about the same price tag as their custom 24. I've only ever heard them in video, but they sound amazing, and I've only ever heard good things about them. I would argue that PRS should have made that top 10 acoustic list at least over Fender or Epiphone.
There’s also the line of self-tuning “robot” guitars that Gibson spent more than a decade and millions of dollars developing. In 2015, Juszkiewicz made the feature standard on most new guitars. Sales dropped so dramatically, as players and collectors questioned the added cost and value, that Gibson told dealers to slash prices. The company then abandoned making self-tuners a standard feature. You can still buy them — they call them “G Force” — but they’re now simply an add-on option.
Early electrics weren’t built for distortion. The idea was to create a loud, clean sound and, with a few notable exceptions, that’s what players who utilize this type of guitar are looking for today. But even without overdrive this design has one inherent problem: As the volume goes up, hollow-body guitars become highly susceptible to feedback. The next level of electric guitar evolution, the semi-hollow body, made a few strides in dealing with this issue.
It is traditional to think that learning guitar initially involves learning lots of chord shapes. I agree that this can be a distraction, and for me, it made the guitar seem more complicated than it is. As well as (or instead of) learning lots of chords 'by rote', an alternative would be to learn a few scales, and learn how to construct chords from those scale shapes.
I understand and concur with you totally, as a sound man, I love it when everyone is direct, it makes life so much easier. every mike you eliminate adds roughly 3 db headroom overall to the max level without feedback. But as a bassist, and a Chapman Stick player, ampless just feels too flat and lifeless for me. I recently worked a John McLaughlin and Fourth Dimension gig in Bali, Both John, and Gary Husband went direct, it was wonderful. The bassist was amped though, for the same reasons I prefer to be amped If I am playing bass. Nathan East is another who doesn’t like bass in the monitors, preferring the sound and dynamic control of having his own amp. By and large, I find that generally (with some VERY notable exceptions) people who grew up playing concerts “back in the day” prefer amps, subsequent generations of people who grew up playing with small “portable” amps (think SWR, etc.) generally don’t mind going ampless, they have pedal racks, and have the sound they want from that. They don’t miss the air moving on their strings, because they never had it.. Perhaps because I am a dinosaur, I need the feel of 6, or 8 10s behind me, (or at least 2 15s), the resonance effect it has on the strings, makes my instrument come alive and it breathes with a feeling no pedal rack can duplicate. You should see Bootsy Collins’ rig, he had 2 1x18s, 2 2x15s, and 2 4×10 boxes, and that is what he calls his “small gig rig”! I guess I grew up regarding the amp as an integral part of my instrument, without it, playing feels, well, like you don’t have an amp! Even in the studio, I run a DI into the board, but I play through an amp for my own feel. Peas.

The guitar is very light in weight and pretty resonant. At this point they were hard-wiring the cord right into the guitar with a nifty spring strain relief on the plug. This guitar has a brighter sound than my Gretsch and I probably prefer it for ultra-clean work because it has that vintage "thang" going on that some call "mojo." I am, however, trying to get the driven sound sorted at this point because of all the overtones. Now I know what sort of sound the Telecaster bridge pickup was based upon!
Another great thing about this guitar is the Min-ETune system that offers 16 tuning presets. This not only makes it super quick to tune your guitar for everyday use, it’s also great if you need to tune your guitar up or down. It saves you a lot of work and time! It’s also a feature that makes these electric guitars for beginners who don’t know how to tune their guitar, and even if they of course can use a tuner this is still a faster option.

Martin's OM, or "Orchestra Model", available from 1929 to 1933, has a rare combination of features. The joining of a long-scale (25.4") neck with a small body makes it an extremely responsive and playable guitar. In many ways the OM models were the first truly modern flattop guitars. They were the first Martins to have necks with 14 frets clear of the body. The OM has a wide neck (1 3/4" as opposed to the dreadnought's 1 11/16") which appeals to fingerstyle players. The string spacing is slightly greater at the bridge than on other models too, although not as wide as a classical guitars. The neck shape of old OMs is a bit unique too, although this is variable since each neck was handmade. OMs have a wide but thin backshaped V-shape which is very comfortable. Finally, the OM's smaller body size makes the guitar easy to hold, especially in the seated position. Compared this to the D dreadnought which is larger both in body depth and width (dreadnought players seem to use straps and stand up so the guitar's size is less of a factor).

Guitar Center Albuquerque provides comprehensive guitar repair services for the Albuquerque area. Our repair technicians are as passionate about your guitars and basses as you are, and we have the experience needed to keep them performing at their best. Whether you need a quick adjustment to make your guitar easier to play, or a complete guitar rebuild, we have the tools and know-how to take care of your instrument. Guitar Center Albuquerque can also help build a maintenance plan that fits you and your guitar or bass needs, including custom setups, restrings and more. We also take care of fret repairs, hardware and pickup installations, upgrades and customizations, bone and graphite services and more.
Hertz Guitar company was originated from Shanghai/China & North Korea. This brand of guitars produces electric and other wide range of guitars that can be used in studio recordings and live shows. This brand also manufactures guitar accessories. The starting price of guitar from this brand is 12,504 INR approximately. Anyone looking for an affordable electric guitar at a beginner and advanced level can buy this brand of guitar.
I have a similar guitar to the one you bought. It was my grandmothers and I'm estimating it at over 30 years old. Very folk style. She told me she actually had the original strings from when she bought it! I believed her when i tuned the thing and the day after found that the 4th and 6th had snapped. From what i know, Decca just made guitars around that time, 60's to 70's. Mine says it has a steel reinforced neck and it is really heavy compared to others. its still in really good shape and I actually play it. I'm not planning on selling it but I know its well worth its age. It has a hand chissled Ser. # on the bridge.
The Marine Band Thunderbird is a model of low and super-low pitched 10-hole diatonic harmonica that was introduced in 2011. It possesses a bamboo comb like the Crossover, and a conical shaped lower cover plate. Designed by noted harmonica player and customizer Joe Filisko, this plate helps reduce any rattle caused by the low frequency tone produced by the reeds. It is available in low major keys A through F, as well as low B-flat and E-flat, and double-low F.[14]
The way that manufacturers state the wattage output of an amplifier can be confusing. Amplifier manufacturers may state that a combo bass amp produces 600 watts at 4 ohms and 300 watts at 8 ohms. If the speaker mounted in the combo amp is an 8 ohm speaker, then the combo by itself will only produce 300 watts. This combo amplifier will only put out 600 watts if an "extension speaker cabinet" is plugged into the combo amp with a speaker cable. Plugging a second 8 ohm cabinet in parallel wiring with the combo amp's internal 8 ohm speaker will lower the amp's impedance (electrical resistance or "load") to 4 ohms; at this point the amp will put out 600 watts. Another factor that can make it difficult for bassists to select a bass amp is that different manufacturers may state their amps wattage in Root Mean Squared (or "RMS") and in "peak power". For example, a bass amp ad may state that it produces 500 watts RMS and 1000 watts "peak power". The RMS figure is much more important than the peak power wattage.
{"eVar4":"shop: amplifiers and effects","pageName":"[gc] shop: amplifiers and effects","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: amplifiers and effects","prop1":"[gc] shop: amplifiers and effects","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"amplifiers & effects","prop5":"[gc] shop: amplifiers and effects","prop6":"[gc] shop: amplifiers and effects","prop3":"[gc] shop: amplifiers and effects","prop4":"[gc] shop: amplifiers and effects","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] category"}
I'm not sure if it's been made clear or not yet, but the imported firewood that had a Kay brand name on it in the seventies bears no relation to the products of the the Kay Co. of Chicago USA. It's not all plywood either; they had a range of total crap to not-so-crappy models. I never much liked their p.u.s or their necks. This is a good body (late 40's K-44) with a better (Harmony!) neck.
Once you are satisfied that the curve of the neck is in the acceptable range, check the string height at nut. Depress each string at the third fret and look back towards the nut to see how the string sits over the first fret. The string should neither be sitting on the first fret nor far enough above that you can see a gap thicker than a sheet of paper. This is a very subtle point to reach and you need proper nut files to set it. This setting is crucial both for achieving proper playing height up the neck, and for achieving proper intonation. If it is too high here, you are going to end up setting the action lower at the saddle than it really ought to be, resulting in buzzing ( the string will measure out "correct" at the 12th fret yet actually be inclining down as it progresses towards the bridge saddles). Additionally, a string set too high at the nut will likely play noticeably sharp at the first and other lower fret positions.

In general, this measurement is taken by measuring the distance between the bottom of the string and the top of the 6th fret while holding the string down at the 12th fret and the first fret. This is where the capo comes in handy - put it on the first fret so your hand is free to take the measurement. Using a feeler gauge of the desired height, in this example, 0.010, hold the low E string down at the 12th fret (with the capo on the first fret), and measure the distance between the top of the 6th fret and the bottom of the low E string. If the distance is greater than the desired relief, then you need to turn the truss rod clockwise (towards your right) as you're looking down the headstock towards the body of the guitar. If the distance is less than the desired amount, then you need to turn the truss rod counter-clockwise (towards your left) as you're looking down the headstock towards the body of the guitar. The basic rule is:
The company makes four models, the FS (fingerstyle), GC, D, and the Jumbo, each retailing at a flat price of $8,880 as of September 2011, making them amongst the most expensive new guitars in the world. The company also provides the option for customized furnishings such as exotic woods, buffalo horn nuts and saddles, mammoth ivory bridge pins and nuts, and specialized inlay and cutaway designs etc for an additional fee. The customized Petros guitars made of rare woods such as African Blackwood, Ceylon Satinwood or old flitch matched Brazilian Rosewood are sold for an extra $4,000 which with other furnishings such as ivory bridge pins can fetch over $13,000 in total.[2]
While production and distribution of guitars under the Ibanez brand began much earlier, the company gained notoriety outside its native Japan when it started importing Ibanez guitars to the United States in the mid-1960s. These first efforts were funky-looking creations which sold at the low end of the guitar market, primarily in department stores. But the company's products continued to move up the quality ladder until the company was perceived as a legitimate market force, selling what were essentially copies of other companies' designs in the mid-1970s. A patent lawsuit from Gibson ended the sales of those copies, but Ibanez had by then gained a foothold in the guitar market globally. (more...)
So you decided to play electric guitar. Once you get a guitar and an amp, the next step is to explore effects. Effects pedals can be separated into groups based on their functions. Understanding the different pedal groups is the key to getting the best sound when chaining them together. The largest pedal group is probably overdrives and distortions, and BOSS currently makes 16 different pedals in this category. For our example pedal board, we’ll pick the ST-2 Power Stack. Another category with many choices is modulation.These are effects like flanger, phaser, chorus, tremolo, and others. Let’s use the most versatile of these—the BF-3 Flanger. Another group is ambience effects, such as delays and reverbs. We’ll use one of each: a DD-7 Digital Delay and the FRV-1 ’63 Fender Reverb. There are some pedal effects that can add notes or alter the pitch of what you’re playing. For want of a more esoteric name, we’ll call these “pitch-altering” pedals. From this category, let’s throw in a BOSS OC-3 Octave. BOSS also has a few pedals that make your instrument sound like some other instrument. The AC-3 Acoustic Simulator will do the job. Some effects change your sound with filtering. This effect type can be used in different places in the signal path, so we’ll use the GE-7 Graphic EQ. A few BOSS effects defy categorization, but are nevertheless very useful in any signal path. The most common of these is the CS-3 Compression/Sustainer. Loopers fall into this category also, so let’s add an RC-3 Loop Station to the mix. And you might want the NS-2 Noise Suppressor to kill the noise in your rig, so let’s add that in, too. What about a tuner? The TU-3 is the most popular pedal tuner in the world.
There have always been slight variations in the color of the cream plastic parts used on Gibson and other guitars. It's not uncommon to see brand new and vintage guitars with bindings, pickup rings, toggle switch rings and pickguards that don't perfectly match in color. We do our best to match all our cream products, but there's no absolute control from batch to batch, or from supplier to supplier.
Maybe the pickups that came with your guitar are just cheap and not up to your standards. At that point, an upgrade might be less of a stylistic issue and would done for the purpose of improving the overall sound quality of your instrument. In most cases, upgrading the pickups on your guitar are the single most effective way to improve the overall tone and sound quality.

The ’62 EG-NT, EG-K and EG-Z were fairly primitive and appear to be leftover from the mid-’50s. The EG-NT had a small rectangular body with the bass side flush with the neck and the treble sticking out a bit to handle the controls. The head was stubby three-and-three with a circle Swan logo sticker and the fingerboard had painted diamond markers. The pickup looks to be the old slotted pickup of the early J-1, but may not be, with volume control. The EG-K was the Teisco version of the Rickenbacker Frying Pan, with a round body and neck with a head wider than the neck. This, too, had the rectangular head with a circle Swan logo. Markers were diamonds, the pickup was the slotted J-1 pickup, with one volume control. The EG-Z had an asymmetrical body with a short width on the bass side and a longer width on the treble side, with diamond markers and the stubby head. This had the old slotted J-1 pickup with volume control.
pay is about HALF of what it should be for this expensive of a product, when a factory is turning out nearly $1 million a week in profits from one factory with less than 50 employees, they should make more than the salary cap of $12-$15 per hr, the only reason you make a decent living wage is because you work so much you don't have any time to live. You may have time to go home and sleep (and eat something, if you're VERY lucky, most days i don't even have the energy to wake up and eat once i get home.
Like so much else, analog delays were first made possible by a shift in the available technology in the mid 1970s, in this case the advent of affordable delay chips. Techies call these “bucket brigade delay chips” because they pass the signal along in stages from the input pin to the output pin—with as many as from 68 to 4096 stages. Inject a signal, govern the speed at which it gets passed from stage to stage, tap the output and, voila, you’ve got echo. It’s clear from this that the more stages in the chip, the longer the delay the circuit can achieve. The longer the delay, however, the greater the distortion in the wet signal, so most makers compromised to keep maximum settings within acceptable delay/noise ratios.
Alternatively – and often most effectively – you can fix phase issues in the digital realm. Record your two-mic signal on two separate tracks, then zoom in on the sound waves in each of the two channels in your DAW’s editing window until they are huge and you’re seeing the full up-and-down crests and troughs of the waves. Now, drag or nudge the sound wave of the ambient mic forward (i.e., to the left of the screen) a few milliseconds at a time until the sound waves line up perfectly. Listen again, and you should hear a very different blend that is fuller, richer, and more “together.”
You are bidding on a previously owned and in good working condition Blackstar Amplification HT Studio 20H guitar amp head. This auction is for the amp and power cable you see pictured. No footswitch is included. Nothing else is included. It comes as pictured. Please take a moment to look at the pictures and get a better idea of what you are bidding on. This unit has some scuffs and dings from being moved around. It has been tested and is in good working condition.
Thinking out loud... what defines electronics then? I've always assumed that the pickups, caps, pots, etc. inside an electric guitar constituted an electronic system. The "guitar's electronics" facilitate a deliberate flow of electrons through a circuit with semi-conductors, etc. Heck, with coils and magnets (and sometimes battery packs), they also provide the electricity that's conducted through the system.
There are several string configurations available with electric guitars, including 4-string, 6-string, 7-string, and 12-string configurations. Although each configuration can make a slightly different sound, the differences are mostly down to personal preference. Nontraditional configurations include 5-string, 8-string, 9-string, 10-string, and 18-string versions.
Like effects pedals, multi-effects processors are used to modify and alter the clean signal of your guitar to produce a large variety of effects (reverb, wah-wah, overdrive, distortion, chorus, etc). Unlike a simple pedal that gives you one or two options for modifying tone, a multi-effects processor has a full load of effects and sounds that allow you to play music with a rainbow-colored tonal palette. There are processors for modifying guitar, bass, and even units for vocalists with pitch-correction tools and harmonizer effects.
A bit underrated and under the radar, Blackstar makes some superb amplifiers at a fraction of the cost you’ll find from bigger name brands. And while it’s a shame they don’t get more recognition, it’s good news for you, the user. This particular amp might just be the best option for apartment living – due to its small stature and low-level volume paired with the fact that it is still a tube amp. But don’t let the fact that it’s only 1-watt fool you – thanks to the simple truth that it uses tube amplification, it can still get plenty loud. Of course, if you’re overly concerned about noise, this option also comes with a headphone jack, and it’s one of the few tube amps to even offer that convenience.
Now that you know a little bit of history behind the electric guitar, let’s dive into some of the different types of electric guitars that you can find at Sam Ash. You may be thinking to yourself, “Why are there so many different types of electric guitars?” The reason is this: each and every type of electric guitar serves a unique purpose and will cater to various types of playing styles and musical genres.