Increasing the bass and treble while reducing or eliminating the centre midrange (750 Hz) results in what is popularly known as a "scooped" sound (since the midrange frequencies are "scooped" out). Conversely, decreasing the bass while increasing the midrange and treble creates a punchy, harsher sound. Rolling off all of the treble produces a dark, heavy sound.
The CD-60CE is a Factory Special Run acoustic-electric guitar made by Fender. This inexpensive model comes with a Honeyburst gloss finish and a solid construction that gives a warm and rich sound. This guitar is made of laminated mahogany all-around. The top features scalloped X-bracing patterns for a wider range of frequencies and a distinctive sound.
The Yamaha Pacifica has long proved a benchmark for quality and specification, and the 112V remains one of the best electric guitars for beginners. The 112 is far from fancy and simply concentrates on the bare necessities. Yet the construction is of excellent quality. Trust us, if looked after this will be a guitar for life. By design it's an altogether more modern, brighter and lighter take on a hot-rod Strat. But when we say brighter that doesn't mean overly shrill. In fact the bridge humbucker will surprise some, it's beefy without being too mid-range heavy and although the coil-split proves a little bland played clean, with a distortion boost it's a pretty useful gnarly and wiry rhythm voice. It's good to have the choice too when mixed with the middle pickup - switching between the full and split coil here is subtle but, especially with cleaner 'class A' amp voicings, there's enough character difference to be useable. The solo single-coils impress - plenty of percussion and with a little mid-range beef added from the amp these get you to the correct Texas toneland. Neck and middle combined produces a fine modern Strat-like mix - the added brightness will cut through a multi-FX patch nicely.

I don’t think beginners should spend a ton of money on their very first electric guitar. However, around the $300 mark you have a lot of options for really great entry level electrics. So, if you’re a beginner with a little more cash available, I say skip the “starter packs” and buy some good, solid gear to begin your journey. Choose from this list and you won’t need to upgrade for many years.
It is a standard dreadnought with 26 frets. There are no electronics, no cutaway, and no fancy upgrades. It has a book matched sitka spruce top, rosewood fingerboard, adjustable rosewood bridge, cream colored plastic binding, rosewood back and sides, and a black inlaid headstock. The neck is not one piece and is made from presumably African mahogany. It has closed gold tone tuners, black beveled pick guard and some plain black line art for a rosette. This guitar is void of polyurethane and has a lacquer finish, so much the better.
Possessing great look and feel, the LyxPro, the amp is small and would work best for headphone, something that is normal with beginner instrument. It also features a digital clip-on tuner that is so perfect for tuning the 6 strings that are designed on the rosewood fretboard. The Canadian maple neck also compliments the rosewood fingerboard and the overall solid wood body finishes for greater sound quality.
Before you begin, it’s important to understand that a book can’t teach you guitar. They’re great as references and serve as a fine starting point, but soon enough, you need to take what you’ve learned and try to integrate it into a performative craft alongside other musicians. If you find yourself getting stuck, take the exercise you’re on to a jam with like-minded musicians who can help you work practically with the material. At the very least, set a backing track and learn how to time those new skills. So much of playing is about feel, which is a magical combination of timing and groove that only exists in the moment.

Regardless of their investment potential or merit compared to Martins, Fenders and Gibsons, the fact remains that clean original Harmony and Kay guitars as well as some of the other interesting student-grade instruments of the 1960s and earlier are quite rare today. Since they were prone to structural problems, many were simply thrown away rather than being repaired. Due to the lack of good repairmen prior to the mid 1970s, attempts to repair such instruments were often as bad or worse than the original problems, further adding to the destruction. Since most of these instruments cost much less than a Martin, Gibson or Fender when new, owners often felt much less of an incentive to take good care of them. Back in the mid 1960s when I was starting out, I saw far more people playing Harmonys, Kays and Danelectos than Martins, Fenders and Gibsons, but for a variety of reasons most of these student instruments have not survived, so that today it is actually a rare occurrence for me to find an original Harmony Sovereign or a good Kay archtop in playable or good cosmetic and structural condition.
{ "thumbImageID": "RGA-series-RGAR42MFMT-Electric-Guitar-Flat-Dragon-Eye-Burst/J55980000002000", "defaultDisplayName": "Ibanez RGA series RGAR42MFMT Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Flat Dragon Eye Burst", "sku": "sku:site51500000051296", "price": "349.99", "regularPrice": "499.99", "msrpPrice": "688.88", "priceVisibility": "1", "skuUrl": "/Ibanez/RGA-series-RGAR42MFMT-Electric-Guitar-Flat-Dragon-Eye-Burst-1500000051296.gc", "skuImageId": "RGA-series-RGAR42MFMT-Electric-Guitar-Flat-Dragon-Eye-Burst/J55980000002000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Flat Blue Lagoon Burst", "sku": "sku:site51500000051295", "price": "349.99", "regularPrice": "499.99", "msrpPrice": "688.88", "priceVisibility": "1", "skuUrl": "/Ibanez/RGA-series-RGAR42MFMT-Electric-Guitar-Flat-Blue-Lagoon-Burst-1500000051295.gc", "skuImageId": "RGA-series-RGAR42MFMT-Electric-Guitar-Flat-Blue-Lagoon-Burst/J55980000001000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }
It's like saying the wood handle of a hammer effects the tone generated by hitting a nail. The nails been hit, vibrations through the wood afterward are pointless. Unless the guitar itself is metal and hollow, you would hear sound generated acoustically, as you would with any acoustic instrument. An electric guitar is not an acoustic instrument in a classical sense.
Adding to their already good value, most multi-effects come with built-in features that are essential to gigging and practicing, first of which is a built-in tuner. Looping is also a good feature to look for, thankfully it now comes standard for most units. Having the ability to record straight to a computer is another handy features that should be considered, as well as the ability to edit the settings via your computer or mobile device. Built-in metronome/rhythm is also a nice plus, especially for those who want to take their skill to the next level.
Guitar lessons work best if you're putting your skills together to learn how to play songs. That's why Guitar Tricks has a ton of great song tutorials for when you've mastered the Core Learning System, or if you want to try something new. These easy guitar songs are great, especially if you're a beginner that recently picked up an electric guitar. 

InstantDrummer provides tempo-sycronized drum loop sessions that can be accessed easily from within RiffWorks guitar recording software. Most RiffWorks InstantDrummer Sessions are loop recordings of professional drummers brought into the InstantDrummer format for easy manipulation by RiffWorks users. Play along with InstantDrummer sessions by famous drummers like Alan White (Yes, Lennon), Jason McGerr (Death Cab for Cutie), John Tempesta (Rob Zombie, Exodus, Testament, Tony Iommi, The Cult), Lonnie Wilson (Brooks and Dunn, Faith Hill, Tim McGraw), and Matt Sorum (Guns N Roses, Velvet Revolver). Use them in your recordings royalty free!
This is one of the best guitars according to many guitarists and there are many reasons for that! It has a nice weight, not too heavy, not too light, and it’s comfortable to play. If you want to find a good guitar but don’t really know what to look for this is a safe choice, you will most likely love this guitar, especially if you like vintage-looking things! Go wireless on stage with this guitar, with one of these awesome wireless guitar systems.
Ovation acoustic-electric guitars are unique, innovative and, for some players, almost addictive! Once you’ve played an Ovation, no other guitar may do. They have a different look and feel than most other acoustic guitars due to their design, which incorporates a wood top with a rounded, synthetic bowl shape instead of the traditional back and sides.
The pre-1945 braces have a scooped or "scalloped" profile, making them lighter in design and weight. Functionally this means a greater vibrating surface (the guitar's top), and provides stronger bass response. Why did the Martin Company change from the lighter scalloped braces to heavier braces? The answer is in the strings. Many guitarists of that time were using heavier gauge strings, and these heavier strings were tough on the lightly constructed scalloped-braced Martins (especially on D-models with the long 25.4" scale). Martin didn't make a heavier guitar to withstand the extra string tension, so they compensated by adding more rigid (non-scalloped) braces to the guitar's top.
Whether you're recording or just plain playing for the fun of it, a headphone guitar amp is a great thing to have. You can even choose headphone amps that will work with pedals, mixing consoles and other connections, giving you a ton of versatility in how you use them. If there's one thing that's universally true about these amplifiers, it's that no guitarist should be without at least one.
Whoa whoa wait, what? This pop artist? A guitar player? If all you’ve ever heard from Mayer is Your Body Is Wonderland, or Daughters, then you’ve got to give his album Continuum a listen to. He is no Shakespeare, but his guitar playing speaks to your soul. His songs will make most glorified tough guys miss their old girlfriend, and the rest just go to a corner and cry. If you think that his songs are all too depressing, then watch some videos of him playing. His guitar face is priceless.
These special qualities have been used for centuries to create and build various instruments with differing levels of success. Some tone woods do it better than others so, are often more vigorously sought out and because of their growing rarity (due, primarily, to over harvesting) also vary in expense, the rarest most hard to find being the most expensive, of course.
Materials for necks are selected for dimensional stability and rigidity, and some allege that they influence tone. Hardwoods are preferred, with maple, mahogany, and ash topping the list. The neck and fingerboard can be made from different materials; for example, a guitar may have a maple neck with a rosewood or ebony fingerboard. In the 1970s, designers began to use exotic man-made materials such as aircraft-grade aluminum, carbon fiber, and ebonol. Makers known for these unusual materials include John Veleno, Travis Bean, Geoff Gould, and Alembic.
I myself own an Ashton and I think that they are overall really great guitars. I own an Ashton SL29CEQLTSB Acoustic Electric and it is simply amazing. It comes with a built in tuner and the strings last for quite a very long time. I have owned a couple guitars in my time and I am happy to say that the sound is impressing. So all of the other people who put down this guitar either know nothing about guitars, are super spoiled and want the best of the best, or just had bad luck with them.
This body and headstock shape are identical to my Nivico Balladeer, and both guitars are real keepers.  This truss rod cover would become the standard curved plastic type seen on many Matsumoku-made guitars for the next 10 years.  Of course the Palmer badge is missing, but the Palmer name (as it pertains to Japanese imports) was being used as early as 1964.  I’ve seen Kawai S80s badged with the Palmer name.  If you do a search for vintage Palmer guitars, you’ll come up with all sorts of hits but you probably won’t see too many guitars like this one.  These were probably made for one or two years, and I’d bet the pickups were sourced from local Matsumoto.
There is a historical parallel between musical styles (baroque, classical, romantic, flamenco, jazz) and the style of "sound aesthetic" of the musical instruments used, for example: Robert de Visée played a baroque guitar with a very different sound aesthetic from the guitars used by Mauro Giuliani and Luigi Legnani – they used 19th century guitars. These guitars in turn sound different from the Torres models used by Segovia that are suited for interpretations of romantic-modern works such as Moreno Torroba.
Nickel trapeze tailpiece with a diamond. For Gibson guitars including the following models- L-50, L48, ES-125, ES-330, etc. Please make sure to check the specs to see if they match your instrument to verify it is the correct replacement. Overall length of Tailpiece not including hinge = 4 5/8 inches. Side to Side width at bar = 3 19/64 inches. Width of string bar = 47/64 inches. String Spacing at Bar = 1 61/64 inches. Important Hinge/Mounting Specs: Mounting Area of Hinge length = 1 1/2 inches. Mounting Area of Hinge Width - 2 inches. Mounting hole location bottom center = 11/32 inch from bottom edge. Two Mounting hole locations from side edges = 5/16 inches. Two mounting hole locations Apart from eachother = 1 25/64 inches. Upper side of hinge length = 1 1/8 inches. Upper side of Hinge width = 1 25/64 inches.

I would like to start off the list of the best small guitar amps by talking about one of the best small guitar amps out there, which unfortunately dedicated the entirety of its existence to being used for the purposes of laying acoustic guitars. Unfortunately, because I would love to have one of these to work with my electric guitars. On the other hand, the fact that the amp works with acoustic guitars best, means that those of you looking for a mini amp for your acoustic guitar are in luck. The amp does a great job of amplifying the sound of an acoustic guitar, keeping it clean and clear of any kind of electric distortion, so that if there was no increase in volume, nobody would understand the point of the pick up. While small, the pick up is still on the larger side as compared to the rest on the list. The design is vintage and cool, so that the guitar is enjoyable to look at for everyone.
Maple is the most common wood used to make guitar necks. It is very hard and dense, and often has attractively detailed grain patterns referred to as figuring. Maple also has a very bright overall tone. Due to it’s figuring and its tonal characteristics maple is often used for a veneer or top laminate on more expensive solid body guitars. It is also used as a top wood in some archtop guitars, where it is usually laminated. Its hardness brings out the trebles in a guitar's sound. It is also often used for the fretboard where it adds definition to the sound. 

To finish, here's one damn good last trick: doubling an electric guitar with... anything else. I know that's pretty vague but I must say that I had a hard time putting it any other way. The goal is to listen to your guitar sound and analyze it to find out what it lacks. Then you "only" need to find a sound that can fill this "hole." For instance, a friend of mine once told me he doubled a crunchy guitar sound with a sample of a lightbulb being rubbed on his boot with the goal of emphasizing the strumming sensation. Much less arcane, there's the famous example of the particularly "fat" riff on Radiohead's Airbag. If you listen to the intro, you can hear that the riff is being doubled with a cello, which obviously adds a lot of the breadth to the sound, as I'm sure you'll agree. I would love to keep on giving you more ideas in this regard, but the scope of this method is so wide and open that the only thing I can tell you is to let your imagination fly, experiment and have fun!

The 50-watt version is driven by seven 12AX7 preamp tubes with two 6L6s powering the amp, which is surprisingly huge in output – capable of filling an auditorium no problem (depending on your cab, of course). Other features that make this such a popular choice among gigging guitarists include three customizable channels and a four-button footswitch.
The F-55 was identical to the F-50 except for the addition of a bridge DeArmond humbucker, plus the attendant three-way toggle on the cutaway horn and a second set of volume and tone knobs flanking the treble f-hole. The F-55, too, had a Martin “M” trapeze tail. This series began with guitar #279831. Some 1,700 F-55s were made from mid-’62 to the summer of 1965.

What worries Gruhn is not simply that profits are down. That happens in business. He’s concerned by the “why” behind the sales decline. When he opened his store 46 years ago, everyone wanted to be a guitar god, inspired by the men who roamed the concert stage, including Clapton, Jeff Beck, Jimi Hendrix, Carlos Santana and Jimmy Page. Now those boomers are retiring, downsizing and adjusting to fixed incomes. They’re looking to shed, not add to, their collections, and the younger generation isn’t stepping in to replace them.

The original electric guitars were hollow. Well, scratch that — the original Electric Spanish guitars were hollow (stick with us for the third installment of “Fundamentals of Guitar Anatomy” on pickups. The first pickup was made for a lap steel guitar!) Gibson took the words Electric Spanish and turned them into an acronym — ES. We commonly refer to these as hollow body guitars.

A typical digital multi-effects pedal is programmed, with several memory locations available to save custom user settings. Many lack the front-panel knobs of analog devices, using buttons instead to program various effect parameters. Multi-effects devices continue to evolve, some gaining MIDI or USB interfaces to aid in programming. Examples include:
The Original Blackout humbuckers are designed to be everything metal, handling thick rhythm play and well-defined lead melodies at higher speeds. The tone has an almost shimmering quality, especially on a clean amp setting. The tone profile of both the neck and the bridge version of this pickup emphasize treble with a hollowed out mid-range that helps give you the best of searing leads and heavy power chords.
Giannini guitars were (and are) made by the Tranquilo Giannini S.A. factory, Carlos Weber 124, Sao Paolo, Brazil. They are generally known for being well-made instruments featuring very fancy Brazilian hardwood veneers, as well as for the strange-shaped asymmetrical CraViola models. Probably the most famous, indeed, perhaps only famous, endorser of Giannini guitars was José Feliciano. No reference materials were available on the early Giannini guitars. A catalog from 1971 is available, with a snapshot of the line that probably goes back at least a decade, and certainly forward.
Excuse me for interrupting but I think that it's not properly to complain about who Clarence didn't added and who he didn't..if you search another site the top 10 will be different..i bet there are no sites who have exactly the same top 10 artists… I found this site because i just wanted to know names of great guitarists.Since you already know some you can create your personal Top 10 for yourself or for a blog or anything. I don't think it's right to influence others with your own opinion. I'm not really that expertised but I thought it would be nice to react. Thank you and no flames intended ^^

vintage harmony h75 hollow body guitar ser 519 1966, vintage 1950s vega odell model e130 hollow body electric guitar in case, vintage 1960s harmony h56 rocket hollowbody w hsc, vintage baldwin electric hollow body 12 string arch top awesome sound and player, vintage egmond hollowbody electric guitar gold foil pu make offer, vintage circa 1956 gibson es175 d hollowbody electric guitar white refin p90, vintage 1966 conqueror 335 shaped hollowbody sunburst arch top hh bigsby style, vintage vantage vsh455 hollowbody electric guitar with original case no reserve, vintage rare galanti hollowbody electric guitar super funky 1960s, vintage 1968 gibson usa johnny smith hollowbody guitar rare doublepickupwohsc, vintage 60s japan mij teisco del rey ep10t thinline hollowbody sharkfin guitar, 1966 harmony h74 hollowbody electric guitar original case clean vintage, vintage kapa series 500 hollowbody electric guitar amp; case usa, vintage bruno conqueror made in japan mij electric guitar hollow body , 1980 ibanez artist as200 vintage hollow body electric guitar, 1967 gibson usa es33512 vintage semihollowbody 12string electric guitar, vintage 1970 gibson es175d hollow body electric guitar, vintage hollowbody electric guitar harmony kay silvertone must see no reserve, 1964 gretsch tennessean 6119 vintage hollowbody electric guitar w bigsby , vintage experienced 1967 harmony h72 hollow body guitar, vintage circa 1967 framus atlantic 5113 semihollow body original cherry red , vintage original circa 1969 aria es335 copy semihollow body electric guitar, vintage 1966 baldwin burns vibraslim semihollow body guitar clean no reserve, awesome vintage hagstrom viking super rare 12 string hollow body w low action, beautiful vintage harmony h75 hollowbody electric guitar, vintage 1960s harmony silvertone model 1429l hollowbody electric guitar w ossc, vintage 1967 gretsch rally hollow body electric guitar bamboo yellow orig case, vintage 1961 epiphone broadway arch top hollow body electric guitar natural , vtg conrad brown sunburst electric guitar es 335 type hollow body wcase j0330, vintage 1970s ibanez model 2358 semihollowbody electric guitar al caiola copy, vintage 1988 gibson es335 jc showcase edition electric hollowbody guitar w case, rare vintage 60s egmond electric hollow body guitar from holland cool, vintage circa 1969 harmony rebel semihollowbody electric guitar sunburst ossc, vintage 1960s vox super lynx hollowbody electric guitar sounds amazing, vintage usa 1972 harmony rebel h81 hollowbody electric guitar near mint wtags, vintage 1954 gretsch 6186 clipper hollywood hollow body w case rare nice, vintage circa 1969 greco hollowbody double pickup electric guitar brown w ssc, vintage circa 1966 made in japan semihollow body electric guitar sunbust clean, 1967 vintage guitar aria diamond 1202t hollow body no case free shipping used, vintage 1966 harmony h59 rocket 3 hollow body red burst finish rare nice
There is not one standard # of frets, but the three most common are 21, 22 and 24 frets. The extra frets simply mean you can play some additional high notes. If you are just starting out, you will probably be just fine choosing 21, 22 or 24 frets. But, you should probably avoid the fretless option unless you're specifically learning how to play fretless instruments.
A lot of EBay sellers have been calling the Hagstrom solid-bodies of the time Hagstrom-Kent. They are not. If it says Hagstrom on the body, it’s a Hagstrom. If it is one of the Hagstrom guitars that was sold as a Kent, it’s a ‘Kent, made by Hagstrom’. I wonder if the sellers think they can get more for a guitar by associating the Kent name with it. I don’t see how. Perhaps the fact that there are so many Kents floating around, the sellers wanted a more familiar name to hang on the Hagstrom.
The Kay Gold Line professional series became synonymous with that rich gutsy Blues/Jazz sound that eventually became rock. This unique blues sound was not available from any other guitar of that time. For the past decade vintage Kay instruments have been fetching high prices and have had increasing interest from collectors and players because of the cool, campy look and that unique Blues/Jazz sound.

Unless you get the guitar that is great for all types of venue, knowing your venue is highly recommended as you might be buying a guitar that has features not suitable or useless to your venue, not only will you be wasting great features for not using it, but you will also be paying for the said features which you will not be using anyway—not practical at all.

This Hellraiser C1 guitar features a mahogany body and a quilted maple top and abalone gothic cross inlays. It looks and feels fantastic! A couple of things that make it sound even better are the locking tuners, that keep it in tune, and the EMG noise-cancelling scheme that makes sure that the only sound the guitar makes is the music you’re playing.
Moving the mic even further back – from a few feet to several – gets into what is generally referred to as “ambient miking” or “room miking.” This can be a great way to achieve even more depth and sense of space in your tracks. Jimmy Page made frequent use of ambient miking in recording his guitar parts with Led Zeppelin, and it was also a major factor in Eric Clapton’s legendary “Beano” tone. The further from the speaker you place the mic, and the more into the center or far side of the room, the great the proportion of reflected to direct sound in the blend, and the greater the sense of “air” and “room” in the sound. Often, it’s combined with a close mic to retain the option of blending in as much punch and directness as necessary, but if you only have one track or one mic available, ambient placement will sometimes do the trick on its own.

Nashville studio engineer Glen Snoddy discovered the Fuzz-Tone sound when recording Marty Robbin’s 1960 hit “Don’t Worry About Me.” Allegedly an overloaded transformer blew in a Langevin tube module, transforming Grady Martin’s bass guitar into a distorted, heavy fuzz. Some put the event down to another case of amplifier malfunction. Either way, Martin continued to use the tone throughout 1961 while Snoddy transistorized the malfunctioning circuit through trial and error, and sold it onto Gibson in 1962.

Jimi Hendrix: Right-Handed vintage white body flipped upsidedown for left-handed use with an oval profile maple-cap neck. The controls and electrics are vintage-modern to ensure stability. The guitar is strung upside down with the strap button on the lower horn, the backwards 68 thick black CBS headstock decal is so that—in front of a mirror—the player sees the guitar as it would appear if Jimi Hendrix played it. As well as this upside-down lefty Strat for right-handed players, Fender also made four exact copies of the Vintage white Stratocaster Hendrix used in many performances, the most famous being Woodstock (1969).
Before World War II, Epiphone was one of Gibson's fiercest competitors in the guitar market—especially when it came to archtops. With legendary models like the Broadway, Deluxe, Emperor and Triumph, they were a force to be reckoned with on the hollow-body electric guitar scene. In the 1940s, Epiphone went from one of Gibson's competitors to one of its subsidiaries, paving the way for Epiphone Electric Guitars to become synonymous with many Gibson models.  Despite this drastic shift, Epiphone continues to be renowned for their archtop electric guitars even today. Models like the Wildkat Royale and the limited edition ES-335 Pro are worthy throwbacks to that golden era of electric guitars, giving you authentic vintage sound that's perfect if you're into classic rock. Another Epiphone original that's still available today is the solid-body Wilshire. The impact that the Wilshire had on guitar design is so strong that it's still one of the first mental images that comes to mind when we think ""electric guitar.""

There are several aspects that make the acoustic guitar different from the electric one. The most notable difference is the fact that the acoustic types do not need a source of electricity or rather they do not have to be plugged in for them to be heard. They are relatively large and are built with a hollow chamber for the magnification of the guitar’s resonance thus giving out sound that originates from the plucked strings. It also has a bridge that is essential for the transmission of vibration of the strings to the body. They are self contained, needing minimal preparation to play. In other words, they are the guitars to be bought by all those looking for simplicity.

Anyway, this little beast didn’t need much work. This is one of the pleasures of working on a Champ-style practice amp. They have so little in them, there’s simply not much to go wrong or fix. This one, it turned out, only needed a filter cap job, a new preamp tube and one coupling cap. Piece o’ cake. Twenty minutes of soldering and one $4.00 7F7 tube later, I had a monster little Champ-esque amplifier (actually it sounds a little more like the Gibson Skylark than a Champ, but that’s cool by me) for under $80.
{"eVar4":"shop: pro audio","eVar5":"shop: pro audio: signal processors","pageName":"[gc] shop: pro audio: signal processors: multi effects processors","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: pro audio: signal processors","prop1":"[gc] shop: pro audio","evar51":"default: united states","prop10":"category","prop11":"multi effects processors","prop5":"[gc] shop: pro audio: signal processors: multi effects processors","prop6":"[gc] shop: pro audio: signal processors: multi effects processors","prop3":"[gc] shop: pro audio: signal processors: multi effects processors","prop4":"[gc] shop: pro audio: signal processors: multi effects processors","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] sub category2"}

Various manufacturers have developed attractive looking multi-effects pedals and claim that their product is the "best". After searching forums, reading customer reviews and talking one on one with the experts, we have shortlisted some of the best multi effects pedals of this year. If you're looking at delaying sound, you may wish to look at a pedal with a delay effect.
Looking for a super-hot, aggressive metal tone? You need a dedicated high-output humbucker that will crush any amp. Whether passive or active, it’s humbuckers that dominate the heavy rock and metal genres, offering huge power, mix-cutting melodic lead tone, and noise-cancelling abilities – just what’s need when the volume and gain increase. For gigging metal guitarists, humbuckers are pretty much essential. This genre has some great affordable options that will turn any axe into a tone monster, as well as some high-end signature pickup sets from legends such as Dimebag Darrell and Mick Thomson, while the premium James Hetfield Humbucker Set from EMG is one of the best purchases a gigging metal guitarist can buy!
DRILLING THE HOLES Now is a good time to drill the holes for the neck, pick up rings, bridge, string furreles, the control plate and cavity. Here is where I wish I had a drill press but I don't, so I just use a hand held drill. It doesn't matter wher you start drilling you holes, just make sure you use the right size bit for the screws that you will put in them later. To figure this out I compare the thickness of the screw minus the threading. A good rule of thumb is to start off with a bit that will produce a hole that is smaller than the screw. If the hole is too small when you try to screw in the screw then you can move up to the next size bit an re-drill. Be careful of the depth that you drill you hole to as well. A good way to do this is to size up the screw with the bit and mark the bit with a peice of tape. This will help you to keep from going to deep.
Hendrix, Van Halen and, uh, Mozart are the musicians to thank for most heavily influencing death-metal shredder Azagthoth, not that they really come through in the jagged riffs and cheetah-fast solos of Morbid Angel classics like “World of S—t” and “Where the Slime Live.” But that’s because he has blazed a tension-filled style all his own (when he solos, he enters a mystical mind state he calls the “Temple of Ostx”) that is finally getting more praise than early antics like cutting himself with a razor before hitting the stage and extolling Satanism.

Nut slots too deep: Take a course file and file the top of the nut 1/2 the distance you want to raise the slots. Catch the filings on a piece of paper. Tape both sides of the nut with masking tape and then fill the slots with the filings. Soak the filings with thin superglue. Press into place with a toothpick. When dry, refile the slots. The slots should be made so the string sits in about 1/2 to 3/4 thier diameter. Slots should be wider, and taper downwards on tuner side. Square slots are acceptable.
The SimulAnalog Guitar Suite is an old but still popular free guitar effects program. It contains a set of VST plugins that emulate some of the most common used guitar effects and amps. It has simulations of five essential guitar effects which include Boss DS-1, Boss SD-1, Tube Screamer, Oberheim PS-1 and Univox Univibe. The SimulAnalog Guitar Suite was born out of an academic research and thus applies a zero deception, no marketing hype approach. The interface is very basic but the sound is said to obtain lass than -40dB of difference compared to the original hardware.
Compressors – The role of these pedals is to lift up quiet sounds and rein in loud sounds, compressing the dynamic range of your signal – that is, the difference between the quietest and loudest sounds. They work wonders for songs with a blend of quiet and loud parts, since they let you play hard without busting eardrums, and the soft sections won’t be drowned out by ringing ears. Compressors also have the nice side effect of increasing sustain, letting your notes sound out longer before dropping off.

This multi-effects pedal lets you setup your virtual rig with up to five effects that include various modulation, distortion, compressor, delay, reverb and other effects. They can also run alongside the Zoom G1Xon's built-in amp modeling, which lets you choose between 22 different amps. Those are a lot of features in a small unit, thankfully Zoom implemented an interface that makes tweaking and configuring easier. As expected although you are still limited by two footswitches, it comes with an expression pedal, which adds even more to its value and usability.
There's just no getting around the Martin brand when there's talk about good acoustics. And since we're talking about the best of them, it's not surprising to find their name filling up multiple slots in this list. The Martin DRS2 acoustic guitar is special because it gives us a true all-solid wood body Martin acoustic guitar - at a very reasonable price point, in the dreadnought shape that the company themselves developed.
Description: Body: Maple - Flamed - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Block - # of Strings: 6 - Scale Length: 25" (64cm) - Headstock: 3+3 - Bridge: Adjustable - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Chrome, 2x Volume Control, 2x Tone Control, 3-Way Switch, Kluson Tuners - Pickups: Harmony - String Instrument Finish: Natural, Sunburst

We noticed in our last article, 10 best Acoustic Guitars Under $500, some readers mentioned the Luna series of guitars. Thank you all for pointing these out! What a truly beautiful line of acoustic and electrics. The Luna Ash, an acoustic electric hybrid is a sleek, responsive guitar ready for any setting: playing live, recording, or jamming with friends. With a mahogany body and rosewood fretboard, this visually stunning guitar is just one in the line of Luna guitars that provides ridiculous eye candy and amazing sound quality and playability. The Ash goes for around $499, and that’s a steal! 

Most Fender guitars are equipped with single-coil pickups. They have a lower output level than dual-coil pickups but sound brighter and sharper, which is perfect for clean and crunch sound. Both the Telecaster and the Stratocaster generally have an ash or alder body, a maple bolt-on neck and a rosewood or maple fretboard. Some other Fender models were also moderately successful (the Jazzmaster, the Jaguar or the Mustang). Squier, a brand that originally manufactured strings, was bought by Fender to become a sub-brand and sell guitars manufactured in Japan from 1982 onwards.
The first guitarist to chain effect pedals together, Hendrix combined their tones and textures with whammy bar squeals and growls and unorthodox playing techniques to make the guitar sound like a symphony, animals, armies or the far reaches of outer space. While most Sixties psychedelic music was banal bubblegum pop with fuzz-tone guitar hooks, Hendrix made music that actually sounded like a trip after ingesting a cocktail of LSD, mushrooms and THC.
There are a very large number of acoustic guitar manufacturers in the world. However, not all are among the best, but this American brand specializes in acoustic guitars. You will find Martin guitars among the top 10 acoustic guitars in the world. It has greatly influenced the look and shape of the American acoustic guitars. Martin guitars are made from highly seasoned wood, which produces some really melodious tones. Mind you, these guitars can be expensive and taking care of the instrument is extremely important. It makes some extremely beautiful models like D-28 and D-45; however, they also manufacture budget-friendly models.
Extra Features: This is where we’ll bucket a bunch of extras that could be important to you, depending where you are in your guitar playing journey, and what gear you might already have. Some multi-effects pedals include handy tools like a tuner, a looper pedal, a built-in expression or wah pedal, an input for an external expression pedal, the ability to double as a USB interface, the ability to be powered by batteries, and so on and so forth. It comes down to personal preference, but we generally like to see the inclusion of a tuner, and looper pedal, since both are extremely useful tools for most guitar players no matter their skill level.
Excellent article. I have found that is a complete waste of time trying to convince guitarist of anything contrary to what they already believe about instruments. The level of passion for the “wood doesn’t matter” camp is truly astounding. We are not testing a new drug or solving cold fusion. The question is simple, does wood make a difference in the tone of an electric guitar? Intuitively, it would seem strange if it didn’t; but, there are many factors that are going to affect the sound produced from a guitar; isolating them is as difficult as creating a study that will convince anyone of an idea they already are clinging to. I think this is a pretty good experiment, better than most I have seen. In the end though, who cares?…really. If someone would like a guitar made out of a Formica counter top…go for it, locking tuners, the pickups and strings of your choice…you’ll be ready to rock. And won’t you be the clever one? As for myself, my opinion, musical instruments have character, a soul if you will. That character comes from the material it is made out of and the craftsman that made it. There is no object more alive than a musical instrument. For arguments sake, lets grant the “wood doesn’t matter” their entire argument. I’d still buy the korina instrument over the countertop. And like most stubborn asses who play guitar, you won’t convince me otherwise.
Gibson has been producing the Les Paul Studio electric guitar since 1983. One of the company’s lower-priced models, the Les Paul Studio was designed to attract guitar players who wanted to have the much-admired Les Paul sound without shelling out cash for cosmetic features found in upper-tier models like the Les Paul Standard. This is why the older Les Paul Studio models did not have headstock inlays and binding on the neck and body.
Be careful. Don't be rash. With the quality of Gibson's 2016 guitars, you should never have too many problems but... if in doubt with an older guitar, take it to a guitar repair pro. You won't need to do it often at all. And it's best to book-in your guitar with an explanation of what you think is wrong. Basic premise: T.L.C. for your guitar, and you'll feel the love back. Oh, and keep your guitar clean!
As a rule, you don't add much, if any, reverb to low-frequency sounds, such as bass guitar or kick drums. Where you need to add reverb to these sources, short ambient space emulations usually work better than big washy reverbs, which tend to make things sound muddy. Taking this a step further, you can also make a mix sound less congested by EQ'ing some low end out of your reverbs.
Custom 24 series have been the bread and butter of PRS for a long time. This guitar has proven to be a really capable axe that can keep up with you no matter where you go in terms of music. A good friend of mine used to own one for a long time, which allowed me to play it numerous times. It’s one of the smoothest and best sounding guitars I’ve ever had a chance to play.
Hugh Padgham adopted a similar tactic for recording Andy Summers' Roland JC120 when working with the Police: "The chorus [was] always switched on in order to produce the slightly out-of-tune guitar sound that was all the rage during the early '80s. The amp's two 12-inch speakers would each be close-miked with a Sennheiser MD421, panned left and right — one speaker would produce a straight signal while the other would be chorused, and these would sometimes be double-tracked the other way around in order to produce an especially wide stereo picture."
Certainly low action makes a guitar easier to play, and for some styles it really is a necessity. What I would like to address here, though, are the high incidences of guitarists who perpetually chase “the perfect tone”, while continually focusing on string height purely as a function of playing feel, rather than as a factor of tone, which it most certainly is. The old set-up rule that you “get your strings as low as you can without buzzing” seems to make perfect sense. Set up to that criteria, however, while your strings might not buzz noticeably, their vibrational arc is more than likely still inhibited by the proximity of the frets. Also, play harder than usual — which, if you’re like me, you will often find yourself doing in live situations, even if you’re not aware of it — and that set up does also lead to a little unwanted buzzing, though your amp settings, the energy of the live gig, and any effects in the chain might help to mask it.
As jazz-rock fusion emerged in the early 1970s, many players switched to the more rock-oriented solid body guitars. Other jazz guitarists, like Grant Green and Wes Montgomery, turned to applying their skills to pop-oriented styles that fused jazz with soul and R&B, such as soul jazz-styled organ trios. Younger jazz musicians rode the surge of electric popular genres such as blues, rock, and funk to reach new audiences. Guitarists in the fusion realm fused the post-bop harmonic and melodic language of musicians such as John Coltrane, McCoy Tyner, Ornette Coleman, and Miles Davis with a hard-edged (and usually very loud) rock tone created by guitarists such as Cream's Eric Clapton who had redefined the sound of the guitar for those unfamiliar with the black blues players of Chicago and, before that, the Delta region of the Mississippi upon whom his style was based. With John Mayall's Bluesbreakers, Clapton turned up the volume on a sound already pioneered by Buddy Guy, Freddie King, B.B. King and others that was fluid, with heavy finger vibratos, string bending, and speed through powerful Marshall amplifiers.
Have you ever tried PRS acoustics before? They come with their SE line, and are fantastic quality guitars for the price. And their American acoustics are built by a small team of acoustic professionals. They only do "private stock" American acoustics now, but they used to have it as a regular lineup with about the same price tag as their custom 24. I've only ever heard them in video, but they sound amazing, and I've only ever heard good things about them. I would argue that PRS should have made that top 10 acoustic list at least over Fender or Epiphone.

Audiffex Guitar Pedals was one of the first professional guitar software packages, with its original version released more than a decade ago. It has since been upgraded but continues its legacy of providing stompbox effects in software form. The latest version is an all in one guitar effects software package - which includes 36 plug-ins that also works for bass, vocals and other instruments. Features include consistent interface with all effects having similar controls, modular plug-in configuration for easier and flexible routing and intuitive preset management. Current retail price: $49

In this tuning, the fourth (G) string is lowered a half-step, thus recreating the intervals between the top five strings, lowered a perfect fourth. Though chords can easily and more fully be played from this tuning, it sometimes results in awkward inversions, a relatively minor problem if the five-string is played in an ensemble with a bass guitar.
If you have been looking for an electric guitar that effectively blend tradition with modernity; the Gibson Les Paul Faded 2017 is the excellent choice that fit such description. This guitar stands as the perfect union between the old and the new—featuring a 490R modern and 490T humbuckers, closely followed with 22 frets designed for amazing bends and great feel.
A guitar recital may include a variety of works, e.g. works written originally for the lute or vihuela by composers such as John Dowland (b. England 1563) and Luis de Narváez (b. Spain c. 1500), and also music written for the harpsichord by Domenico Scarlatti (b. Italy 1685), for the baroque lute by Sylvius Leopold Weiss (b. Germany 1687), for the baroque guitar by Robert de Visée (b. France c. 1650) or even Spanish-flavored music written for the piano by Isaac Albéniz (b. Spain 1860) and Enrique Granados (b. Spain 1867). The most important composer who did not write for the guitar but whose music is often played on it is Johann Sebastian Bach (b. Germany 1685), whose baroque lute works have proved highly adaptable to the instrument.
Guitar effects and the boxes that generate them have married theory and practice, history and material, content and form. Such strange logics, inherent to all of these simple devices, radiate sincerity in their transgressive sounds. Or put differently, those “unmistakable sounds,” which can enchant an entire generation, are not entirely intentional, but are born from the accidental collisions between transistors, tubes, wiring, and luck.

The most important thing to a 5string is the tone ring with a resonator, I've been plays 36yrs. I have an Alvarez Denver belle flat top tone ring, a White Eagle archtop tone ring and my favorite is a Hohner artist flat top tone ring. Regarding a guitar my choice is a Martin D-35 ease of play & tone that is awesome! a 5 string take Many hours & months of practice on your rolls, forward, backward alternating thumb pattern, keeping your timing in check so you do not hit the string with your middle finger out of synch. Good luck have fun, no time better to learn than now!
The earliest extant six-string guitar is believed to have been built in 1779 by Gaetano Vinaccia (1759 - after 1831) in Naples, Italy; however, the date on the label is a little ambiguous.[37][38] The Vinaccia family of luthiers is known for developing the mandolin. This guitar has been examined and does not show tell-tale signs of modifications from a double-course guitar.[39] The authenticity of guitars allegedly produced before the 1790s is often in question. This also corresponds to when Moretti's 6-string method appeared, in 1792.

It's the neat switching that makes this very classic-looking Tele act a little differently. All the standard Tele pickup selections - bridge, bridge and middle (in parallel) and neck - are in place, but it's a four-way switch, as opposed to the standard three-way; the additional selection provides us with both pickups in series for a bigger, louder and more humbucker-like 'secret' sound. The volume control has the S1 push switch in the top of the control knob: pushed down, the parallel and series-combined pickup selections are out-of- phase, giving three additional sounds over the standard Tele. The Baja sticks relatively close, of course, to the classic 60s Tele recipe. The rosewood 'board and alder body just seem to give that lovely smoothness to the high end that will make it less ear-wearing, especially if you're swapping over from an older-style humbucking Gibson. The standard mix is typically classic, wider than a Strat's but still nicely textured; the neck pickup here sounds a little fuller than some older readers or vintage Fender electric guitar owners will remember.

The Kay Gold Line professional series became synonymous with that rich gutsy Blues/Jazz sound that eventually became rock. This unique blues sound was not available from any other guitar of that time. For the past decade vintage Kay instruments have been fetching high prices and have had increasing interest from collectors and players because of the cool, campy look and that unique Blues/Jazz sound.
Before I start, I want to mention a few things about this particular guitar. It looks and (potentially) sounds great. The neck plays well too, but it has some tuning problems and buzzes a bit more than I’d like. The tuning problems are coming from two areas. Firstly the nut slots are too tight, made evident by the strings making a pinging noise when they are tuned up or down. This means that it is difficult to fine tune, as the string’s pitch tends to “jump” up or down. The second reason for the tuning issues is that the intonation is way out. By that I mean that the saddles’ forwards/backwards positions are not set up well, and so when the open strings are correctly tuned, and we then play up the neck, it suddenly seems out of tune again.
The materials and the methods of classical guitar construction may vary, but the typical shape is either modern classical guitar or that historic classical guitar similar to the early romantic guitars of France and Italy. Classical guitar strings once made of gut are now made of such polymers as nylon, with fine wire wound about the acoustically lower (bass side) strings.
Slash is a longtime fan of legend Seymour Duncan’s hand-wound pickups, and for his new Epiphone Firebird, Slash choose custom Seymour Duncan "Slash" open coil-humbuckers for the rhythm (APH-1) and the lead positions (APH-2). These were Slash’s first custom pickups made with Seymour Duncan and feature Alnico II magnets and are slightly overwound for a boosted output. Each pickup has a single conductor cable, a long-legged bottom plate, and a wooden spacer. Controls include individual Volume and Tone pots with traditional Black Top Hat knobs with metal inserts and pointers along with a Switchcraft 3-way Toggle switch. Tone controls for both pickups also feature Sprague "Orange Drop" capacitors (0.022uF, 600V, 5%), the same capacitors Slash uses on his custom designed Les Pauls.
My granddaughter really liked this book. I know it was used but the CD and the wall chart were missing. I wish that would have been noted in the comments. Some of the other book sellers noted that one or the other of these were missing so I didn't order from them. Nothing was noted in the comments on this. My granddaughter was happy with the book and wanted to keep it.

Pedals that fit this description usually end up being more of a problem than anything else, but that’s not the case with Behringer. We get rudimentary but functional controls, which allow you to dial in a decent variety of reverb effects. Same goes for shaping said reverb. You have a certain amount of maneuvering space to work with, which might not seem like a lite when you put this thing next to a boutique model.
Along with the options mentioned, be sure to check out overdrive pedals like the Ibanez Tube Screamer or the Boss Super OverDrive SD-1. As for distortion pedals, be on the lookout for the TC Electric Dark Matter Distortion Pedal or the MXR M75 Super Badass Pedal. Whether you're going for a heavy Sabbath-like snarl, the cutting buzzsaw tone of Johnny Ramone or Cobain's feedback-drenched squeals, the distortion and overdrive effects pedal for you is waiting in this catalog.
And, well do a whole lot of other little wonky sound-altering tricks that an engineer on the guitar factory (or a brave dude with a drill and a soldering iron) can think of. I've actually seen some people attach effect pedals to guitar bodies to have access to the knobs while they play (namely Zvexx Fuzz Factory comes to mind). Of course, that can also make the guitar look super high-tech with all of the switches, LEDs and knobs - to a less experienced viewer.
I learnt to play guitar in my late teens, mainly because it was cool and the girls seemed to like hanging out with guitar players. I started off with a couple of weekly lessons with an elderly lady who managed to teach me some basic chords. After that I continued learning from friends because, imagine this, there was no internet at that time and no cool dudes who knew how to teach to play pop and rock guitar. Well, I strummed my acoustic hard and moved into playing folk and some bluegrass and had fun basking with friends on weekends and during school holidays.
achieved by the creators. A lot of YouTube channels can be very amateurish and suffer from poor video quality, muffled audio and presenters who don’t work well with a camera. And it doesn’t matter if the lesson is coming from someone in the same room or from a studio on the other side of the world, the guitar teacher needs to be good. Someone who communicates clearly and makes you feel welcome.

From an appearance perspective, at least, the most important aspect of the guitar is the body’s finish. The finish of most electric guitars is either a nitrocellulose lacquer, a polyester, or a polyurethane. Nitrocellulose, for the unfamiliar, is highly flammable and also known as gun cotton. It is obtained by the nitration of cellulose, an important structural component of plants. In guitar coatings, nitrocellulose is blended with other compounds and organic solvents to create a lacquer. The solvents evaporate as the lacquer dries.
There are a few ways to save some money on your electric guitar (click for modal analysis). One way is to order online, for example from Amazon, which is usually cheaper than buying from a physical shop. Make sure that you know what the usual price for the guitar you want is, so that you can compare different sites, and in the best of worlds, use a discount code or wait until there’s a sale.

This is a great local shop.  I bought a new Floyd Rose bridge for one of my electric guitars and brought it to Franklin Guitar to be installed and set up.  I got the guitar back within 2 days and it plays so well that I brought them my other guitar for a set up the next day.  Again, within 2 days I had it back and it plays exactly like the other one...awesome.  I had both guitars set up for a little more than half of what another shop quoted me just to install and set up the new bridge on the one.  High quality work at a fair price in a reasonable time...I won't go any where else to have my guitars worked on.  They also have a good inventory of guitars and amps for sale to fit any budget.
You’d be hard-pressed to find a more distinctive guitar tandem in modern metal than Zacky Vengeance (Zachary Baker) and Synyster Gates (Brian Haner, Jr.). From their sound, to their look, even to their names, the duo routinely go down guitar paths other metal axmen don’t dare travel, spicing up Avenged Sevenfold’s otherwise dark and aggressive attack with, among other things, hooky, major-key melodies, laid-back acoustic picking, buoyant, carnival-esque rhythms and a whole lot of style.
Thank you for supporting Ibanez Collectors Forum. Please help your favorite Ibanez guitar site as we endeavor to bring you the latest information about Ibanez custom vintage electric and acoustic guitars. Here you can discuss ibanez, guitars, ibanez guitars, basses, acoustics, acoustic, mandolins, electric guitar, electric bass, amplifiers, effect pedals, tuners, picks, pickups.
000-28EC[10] and 000-28ECB: Two of the five “Eric Clapton” models. Same body size as the 000-15, but with the Martin short scale (24.9″). This artist signature model is constructed with higher-quality woods (especially the more expensive 000-28ECB constructed from Brazilian Rosewood, hence the “B”), a different shape to the neck, and more ornamentation around the edge of the body.
Based both in Japan and the USA, this Japanese manufacturer produces guitars under different brand names: "ESP Standard," "ESP Custom Shop," "LTD Guitars and Basses," "Navigator," "Edwards Guitar and Basses," and "Grass Roots." Hisatake Shibuya opened his "Electric Sound Product" store in 1975 where he used to sell guitar spare parts. He then started to build his own parts and became a Kramer and Schecter subcontractor. His first signature guitar went to George Lynch (the Kamikaze), while the powerful Gibson Explorer copy designed for metal heads and adopted by a certain James Hetfield (Metallica) became almost as popular as its owner in the late 1980's and early 1990's.
I have many acoustic guitars in the collection including Gibson, Taylor, Fender and Washburn. That said none of these guitars come close to the richness in sound of a Maton. I'm assuming this is due to the quality of the Australian timbers and workmanship. Although a little expensive I highly recommend you at least play one in a shop as a treat and hope a dead relative leaves you some money to give you an opportunity of taking one home.
Rosewood is another commonly used kind of wood when it comes to the fabrication of guitars. Rosewood is typically dense, a reason why it is used when constructing a guitar’s fretboard. Although it can be employed in the making of guitar bodies, the resulting units are known for being a little heavier than the alternatives. These guitars can be either brown or blonde.

We’re bookending this article with two Epiphone guitars. Why? Because Les Paul was the man. And G-400 Pro was actually a successor Les Paul model from ’61 to ’68, making this guitar a true icon of rock, power, and endless sustain. With a mahogany neck and rosewood fretboard, this guitar has the looks and, with Alnico Classic Pro humbucking pickups, the tonal quality is excellent. 

Although originally founded in California in 1979 as a company that made replacement parts for guitars, Schecter now produce many models of their own – both mass-produced and custom shop guitars. Like the others on this list, Schecter provide guitars for some big names and have a range of signature models including the guitars of Dan Donegan, Keith Merrow, and Jeff Loomis.

Chords are the heart and soul of playing guitar. Many guitar players seldom do anything else, other than strumming chords. The chord is the basic building block of guitar music. A chord is simply a combination of two of more notes played simultaneously. Different combinations give you different chords. There are different classes of chords, such as Major Chords, Minor Chords, Triads, Suspended Chords, Diminished Chords, etc...
• Heavy is as Heavy Does: For low hanging alternate tunings like open D or dropped D, consider a heavy string gauge – at least .11s, although Stevie Ray Vaughan, who kept his instrument turned down just a half-step, employed a set gauged .13 to .58. Thicker strings will maintain their tension better when they’re low-tuned, which makes for less fret noise and other undesirable distortion. Many players feel thicker strings make for better slide playing, too, since the strings resist going slack under the pressure of the slide. But that’s really a matter of feel and learning to control a slide more than a string thing.
I think the best is at DiGiSTORMERS :: Online Music Studio - Home digistormers website and there is an acoustic guitar vsti which sounds like the real one in the products plugins section. I never use anything else. I used to record live guitars, but using this it is not needed anymore. Also mistakes are recorded!!! It is not perfect then, so it sounds more realistic.
As both the British invasion and the 1960s came to an end, Rickenbacker guitars fell somewhat out of fashion; however Rickenbacker basses remained highly in favor through the 1970s and on. Perhaps as an echo of the past, during the late 1970s and early 1980s, Rickenbacker guitars experienced a renaissance as manyNew Wave and jangle pop groups began to use them.

I've been to Steve about a dozen times with my guitars, families and friends instruments and have sent several people there and have nothing but great things to say.  He is reasonably priced and likely one of the most talented and experienced Luthier's in Boston.  It's rare to see any establishment get 5 stars from so many people and Steve deserves it!  Only thing is, if you're in a rush to get your instrument back, go somewhere else where they do it quickly and without much thought/TLC.  Steve takes his time to do it right and has a lot of customers because he's the guy to go to in the greater Boston area. Highly recommend!
Vox quickly grew. In 1964 Tom Jennings, to raise capital for JMI's expansion, sold controlling interest in JMI to the Royston Group, a British holding company, and sold American rights to the California-based Thomas Organ Company. Displeased with the direction his old company was taking, he left the company in 1967, which was around the same time that Marshall overtook Vox as the dominant force in the British guitar amplifier market. While Royston's Vox Sound Equipment division set up new operations in the Kent town of Erith, Tom Jennings set up a new company in his old Dartford location, joined later by Dick Denney. Jennings Electronic Industries operated for several years, making an updated and rebadged version of the AC30 along with other amplifiers, as well as a new range of organs.
• Why frets come loose: Wear from string contact, fretboard drying and jarring mid-gig or during transportation can cause frets to pop loose. And if binding loses moisture, that can cause the ends of frets to rise or be exposed. These all create troubles that can wrongly be blamed on the more typical problem of fretwear, but in these cases dressing or replacement isn’t necessarily the answer. If there’s enough fret wire left, a loose fret can be reseated in its slot along the fingerboard, and a skilled luthier can often fill the gaps between the binding and the fret ends.
Nut slots too deep: Take a course file and file the top of the nut 1/2 the distance you want to raise the slots. Catch the filings on a piece of paper. Tape both sides of the nut with masking tape and then fill the slots with the filings. Soak the filings with thin superglue. Press into place with a toothpick. When dry, refile the slots. The slots should be made so the string sits in about 1/2 to 3/4 thier diameter. Slots should be wider, and taper downwards on tuner side. Square slots are acceptable.

Digital reverbs, like their sibling delays, offer more power and a greater variety of settings. And in addition to doing some approximations of spring reverb sounds, digital units usually offer more “lifelike” reverberation as heard in anything from an empty room to a large concert hall, if you want to add a synthesized “natural” room sound to your signal rather than merely replicate the classic sproing of springs. A few pedals do this very well, but most such devices are rack units that are best used in an amp’s FX loop, and are beyond the scope of this article. For all the power of digital reverbs, however, there are plenty of guitarists who just don’t warm to them, and the tube-driven, analog, spring reverb effect remains hands-down the favorite for guitar.

Tapping, in which both hands are applied to the fretboard. Tapping may be performed either one-handed or two-handed. It is an extended technique, executed by using one hand to tap the strings against the fingerboard, thus producing legato notes. Tapping usually incorporates pull-offs or hammer-ons as well, where the fingers of the left hand play a sequence of notes in synchronization with the tapping hand.