Pete Townshend turned his guitar into a machine gun. That was the actual sound he went after, slamming his guitars into speaker cabinets and toggling the pickup-selector switch violently. “To me the guitar was a symbol,” explained the Who’s lead guitarist. “It was a metaphor for a machine gun. And the only thing you could do with a machine gun in the 60s was break it across your legs. That’s what I did.” You can hear these specific sonic strategies on songs like My Generation and Anyway, Anyhow, Anywhere.

An instrument unlike any other, the electric guitar gives musicians a feeling and hands-on experience that's nearly indescribable. Even with the same electric guitar, no two players sound exactly alike. Every nuance of the player's hands comes out in the electric guitar's tone, both in fretting and plucking the strings. The best players master not only command of the electric guitar, but also its interaction with their effects and amplifier. It's difficult to imagine a world without the combination of the electric guitar and amplifier, yet it's still relatively new in music. By the turn of the twentieth century, it only made sense that the popularity of the guitar would soon be combined with the onset of electronics. Over the past 75 years, the electric guitar has established itself as one of the most iconic, unforgettable instruments in the world. From jazz and big band to rock 'n' roll and funk, popular music would be drastically different today had it not been for the electric guitar.

You can use compression not only to keep levels under control but also to increase sustain. Sometimes a guitar part will work better in a track if the sustain is created using a little less overdrive augmented by compression rather than relying on overdrive alone. Even a heavily overdriven guitar sound can be made to appear more powerful if compressed, as its average energy level is increased further, though any noise will also be rendered more obvious. Clean guitar parts can also benefit enormously from compression, as it creates a more dense, even sound and can emphasise the picking attack of the notes when a longer attack time is set. Using a faster release time, so as to cause audible level pumping, can make for exciting rock guitar sounds, but some compressors pump more gracefully than others — Dbx models are quite popular in this respect.
Kasuga produced their own house brand in Kasuga guitars. For a brief period of time the company produced Yamaha acoustic guitars. Kasuga guitars were first sold in America in 1972. Unlike many Japanese manufacturers who outsourced their guitar production in other factories outside the main maker, Kasuga produced all their products in-house. Badged guitars known to have been made by Kasuga include Conrad, Emperador, ES-S, Ganson, Heerby, Hondo, Mei Mei and Roland. Kasuga went out of business in 1996.
The open strings of a guitar can be tuned to microtonal intervals, however microtonal scales cannot easily be played on a conventional guitar because the frets only allow for a chromatic scale of twelve equally spaced pitches, each a semitone apart. (Certain microtonal scales, particularly quarter tones, can be played on a standard guitar solely by adjusting tunings, but the distance between notes on the scale makes it somewhat impractical.) It is possible to play microtonal scales on a fretless guitar, to convert a fretted guitar into a fretless, or to make a custom neck with a specific microtonal fret spacing.
Flanging is the strongest of the standard modulation effects. The feedback control increases the depth of the 'comb filtering' produced when a delayed signal is added back to itself. Because it is such a distinctive effect, it is best used sparingly, though it can also be used to process a reverb send to add a more subtle complexity to the reverbed sound.
Several neck shapes appear on guitars, including shapes known as C necks, U necks, and V necks. These refer to the cross-sectional shape of the neck (especially near the nut). Several sizes of fret wire are available, with traditional players often preferring thin frets, and metal shredders liking thick frets. Thin frets are considered better for playing chords, while thick frets allow lead guitarists to bend notes with less effort.
Years of hard-earned success and fame have not changed his down-to-earth attitude. Even though he has become one of the world’s richest rock stars, he hasn’t married a supermodel or become a pompous art collector. Instead, he’s remained true to his working-class roots, spending his spare time building incredibly cool kustom cars and cruising the streets with his car club buddies, the Beatniks of Koolsville.
As you can see, this is simply a case where the Les Paul Custom is a feature-rich product, with more qualities that Epiphone can highlight as buying incentive. All the same contextual advice applies, as the LP Custom is every bit as versatile as the Standard (if not more) and can hang in just about any musical style. When deciding between them it's more a matter of price and aesthetics than any kind of style or playing scenario.

This is one of the best guitars according to many guitarists and there are many reasons for that! It has a nice weight, not too heavy, not too light, and it’s comfortable to play. If you want to find a good guitar but don’t really know what to look for this is a safe choice, you will most likely love this guitar, especially if you like vintage-looking things! Go wireless on stage with this guitar, with one of these awesome wireless guitar systems.

Categories: Guitar manufacturing companies of the United StatesGuitar amplifier manufacturersManufacturing companies based in ChicagoManufacturing companies established in 1890Companies disestablished in 19681890 establishments in Illinois1968 disestablishments in IllinoisDefunct companies based in IllinoisMusical instrument manufacturing companies of the United States
Gibson Les Paul and Fender electric guitars can retail for several thousands of pounds, but electric guitars for beginners are available for less than £100. One example of a cheap electric guitar is the LA Electric Guitar + Amp Pack, which features everything a beginner needs to start playing the guitar right away for under £90.00. It includes a 15 watt guitar amp with 6.5" speaker for practising, a guitar lead, a strap, a padded gig bag, a set of spare strings, a pick and a 2-year warranty. The electric guitar itself has a neck made from maple - the most common type of wood used in necks - which helps to expand on the treble sounds of a guitar due to its hardness. The guitar is capable of producing a wide variety sounds, thanks in part to its 3x single coil pickups with a reverse wound middle pickup, which enables users to experiment with playing different styles of music.

The most defining feature has got to be the neck. It’s thicker than the standard Strat neck, which gives extra meat to work with when bending those strings. Even the fretboard was designed around this technique, with its narrow frets and flat fretboard. It’s not the cheapest one out there, but Fender Stevie Ray Vaughan Stratocaster is definitely one of the best Strats around.
We indicate and report to EMS Worldwide Express mail service that the guitar is sent with a lower declared value than the purchased price and as a gift so that there will be a possible exemption on custom clearance fees, taxes or you may need to pay a little amount but it is necessary, or the custom will open the package and revalue the guitar. Based on our experience, the custom fees in the Europe, USA, Canada, Australia and Asia are very minimal since we declared the guitar as a gift and lower purchased price in order to lessen the custom fees or even possible exemption and we have not received complaints from our valued customers regarding custom fees, taxes and tariffs.

The Hummingbird Pro's unique look breaks the typical monotonous appearance of conventional acoustics, and it does so without straying too far from the familiar. It is easily identifiable by its uniquely shaped ornate pickguard, which matches the guitar's faded cherry sunburst finish. Whether you are on stage or just jamming with friends, you can be sure that this acoustic will stand out.

Gibson Brands, Inc. is considered as an American producer of guitars and other instruments, which is located in Nashville, Tennessee. The brand was earlier known as Gibson Guitar Corp. The company was founded by Orville Gibson in 1902. They are famous for its innovative and superior quality guitars. They sell their guitars under different brand names. These guitars are available at little higher rates. The price range starts from Rs. 49,500/- onwards (approx). For more details, visit
The DI approach most likely to capture the spirit of the original sound is to take a DI feed from the speaker output of a conventional guitar amplifier and feed this into the type of speaker simulator that also includes a dummy load to keep the amplifier happy (valve amplifiers can be damaged by running them into an open circuit). Emulators with a built-in load are generally very much larger than the regular DI box-size emulator-only products. Some of the emulator-only devices can be run from a speaker output, but you still need to plug in either a separate dummy load (usually an 8Ω resistor rated at over 100 Watts on a heat sink) or the original speaker to protect the amplifier from possible damage. Apart from the dummy load, which is passive, the circuitry may either be passive or active.

I've had a Sunburst pattern Ventura when I was a teenager.. it was a nice guitar and played well. recently i saw a really well made Oscar Schmidt gs-1 . not expensive at all. My main guitar for many years was a Gibson howard roberts "artist" dove style. wine red and mother of pearl inlay and gold plated. I eventually sold it to a lady in alaska that plays a lot of blue grass and pop. I got full money out of it. I had it 25 years, so it was vintage by now.
Play power chords easily with one-finger barre'd across two (or three) strings. Simply place your index finger over the sixth & fifth stings at the same fret. (You can also barre the 4th string, which is also a D, and will match the root of your chord one octave higher.) The resulting power chord is named after the note played on the sixth string. At the first fret, it's D#5, at the third fret, it's F5. For tunes blues-rock tunes that use a lot of 5 & 7 power chords, such as those made famous by Chuck Berry, Drop D tuning allows you to play those 7 chords as though they were normal power chords.

Tremolo bars - Many lower-end guitars are designed to look cool and are equipped with floating bridges for super tremolo bends and flutter. They look cool , but a sad fact is many of these lower end models have low quality hardware. There is nothing more frustrating than being a newbie, buying a hot looking guitar, and have to fine-tune it every 2 minutes. Avoid this, or buy a decent bridge for around $100.00 extra and install it.
With two decades of experience and thousands of local customers served I found myself unemployed/downsized in 2010 asking myself what I wanted to do next. After some searching I understood that I really enjoy the interaction that takes place in the local store between the customer and the shopkeeper. I know that we can offer the same prices as the big stores and hopefully make the experience more enjoyable.
As with other plucked instruments (such as the lute), the musician directly touches the strings (usually plucking) to produce the sound. This has important consequences: Different tone/timbre (of a single note) can be produced by plucking the string in different manners and in different positions. For example, plucking an open string will sound brighter than playing the same note(s) on a fretted position (which would have a warmer tone).
{"eVar4":"used: guitars","eVar5":"used: guitars: electric guitars","pageName":"[gc] used: guitars: electric guitars","reportSuiteIds":"guitarcenterprod","eVar3":"used","prop18":"skucondition|0||creationdate|1","prop2":"[gc] used: guitars: electric guitars","prop1":"[gc] used: guitars","prop17":"sort by","evar51":"default: united states","prop10":"condition","prop11":"used","prop5":"[gc] used: guitars: electric guitars","prop6":"[gc] used: guitars: electric guitars","prop3":"[gc] used: guitars: electric guitars","prop4":"[gc] used: guitars: electric guitars","channel":"[gc] used","linkInternalFilters":"javascript:,","prop7":"[gc] used"}
Jump up ^ Wright, Michael. "Jack Westheimer — Pioneer of Global Guitarmaking". Vintage Gutiar (July 1999). In August ’69, the Valco/Kay assets were auctioned off and W.M.I. purchased the rights to the Kay brand name. W.M.I. began to slowly transition Teisco del Rey guitars to the Kay brand name, which gave them greater credibility with dealers. This change was completed by around ’73 and the Teisco del Rey name then disappeared. This explains why you will occasionally see a Teisco guitar with a Kay logo.
Here we have another Vintage Japanese GREAT find this example a beautiful pretty much exact copy of a vntage Martin D-45 ... this is a very High Quality built Lawsuit era Aria Pro II Model AW40. Made in Japan. From information on the Internet concerning dating these, the guitar's serial number would lead to 1976 manufacture. However, I could not find the AW40 model cataloged until the late 70's... but its a 76.. is consistent with all others. THIS is one beautiful guitar! it exudes fine detailed craftsmanship this was Aria's flagship dreadnought of this time period with D41-ish features. From an original vintage Aria catalog, AW40 features include: "Dreadnought sized, Solid Sitka Spruce top, Solid Brazilian Rosewood back and sides, bridge fingerboard and veneer headstock overlay with MOP logo, Marquetry Purfling" ( Top looks to be solid with the sides & back appears to me to be laminated )The catalog can be viewed at, a site that deals with the history of Matsumoku made instruments like Aria, Electra and others. This guitar has the Martin classic snowflake mother of pearl inlays, abalone binding and rosette, and fully bound headstock and gorgeous rosewood fingerboard. Headstock also has a Rosewood overlay. The bookmatched rosewood on the back side is especially easy on the eyes. The guitar is all original with no repairs and with original tuning keys. It is in JVG Rated condition as excellent used vintage 8.8/10 WoW...its 35 years old and the woods have opened up now like fine wine the tone is richer & mellowed as only time can provide. No cracks or repairs ever. It plays very well with good action and has a nice warm rich tone. The Neck is arrow straight. Frets have minimal wear with no buzzing anywhere on the fingerboard....this is the one! At this link you can view more pictures of this guitar please cut & paste the following link:
Hum cancelling: hum cancellation is caused by reverse polarity, reverse winding keeps a revrse polarity pickup in phase with a non reverse polarity pickup. To reverse the direction of the winding, simply swap wires, using hot as the ground and ground as the hot. Polarity can be changed on many pickups. If the pickup has bar magnets, simply flip them over. If the pickup uses alnico polepiece AND has the new plastic bobbins such as is common on Fenders, the polepieces can be pushed out with a screwdriver and reinserted "upside down". If the bobbin is fiber DO NOT attempt to flip the polepieces; the wire is wrapped directly around the polepieces and will almost certainly be damaged.

Jazz guitarists are not limited to single note improvisation. When working with accompaniment, chord solos are created by improvising chords (harmony) and melody simultaneously, usually in the upper register on strings 1,2,3 and 4. Wes Montgomery was noted for playing successive choruses in single notes, then octaves and finally a chord solo - this can be heard in his improvisation on the standard Lover Man (Oh, Where Can You Be?). When playing without accompaniment, jazz guitarists may create chord solos by playing bass, melody and chords, individually or simultaneously, on any or all strings - such as the work of Lenny Breau, Joe Pass, Martin Taylor and others. This technique can be also be incorporated into unaccompanied soloing: for instance Django Reinhardt's "improvisations", as he called his solo pieces.
With parallel effects loops, half the the signal from the amplifier’s preset section is sent through the Effects Sent OUTPUT to pass through effects, while the other half passes directly on to the amplifier’s power amp section to always be heard unaffected.  With this type of effects loop, there is typically an effect level control that allows you to dial in the amount of the effect you want heard along with your unaffected signal.  We recommend setting the MIX control on any of your effects to 100% when placed within a parallel effects loop.  Our TimeLine and BigSky pedals have a Kill Dry feature (DRYSIG parameter in the GLOBLS menu) that mutes your dry signal for use in parallel effects loops—however we do not recommend using this setting when using more than one pedal within the effects loop.
As stated previously, the closer 2 coils are to one another, the greater the cancelations will be when they go "out of phase". So, wiring a humbucker out of phase with itself is going to produce a lot of cancelations, a huge reduction in volume and a very thin sound. If that's not enough, the pickup will not be humbucking either. Still there are some people that like this kind of sound. The best way to put a humbucker out of phase with itself is to wire the coils out of phase in series. (see below)
The Squier Deluxe Stratocaster by Fender is another excellent electronic guitar for newbies. The body is made up of basswood which is a soft, light wood with some of the best mid and upper frequency production. A maple neck and fretboard further assists the mid and high range frequency sound. Its C-shaped neck guarantees the best comfort. This guitar features three single coil pickups. One is assigned for master volume control, one tone control for the neck pickup and one tone control for medium pickup. The five-way switch lets you combine these three pickups and produce the widest range of sounds ever!
"The library has a huge amount of great samples covering every nook & cranny of the electric guitar, and it really is of the highest quality... I could tell that they must have put in a gigantic effort into the scripting, sampling, and design... It’s easy to use, has extensive options for articulations, sounds even better with its effects, and yet it can have a pristine, clean sound as well. I highly recommend it... When they say 'Absolute Electric Guitar' on their website, those words are a lot to live up to [and] they achieved this with a brilliant product and awesome sound." Rob Mitchell (SoundBytes Magazine)
In 1957, president Sydney Katz introduced the Gold “K” line of archtop and solid body electric guitars[14] to compete with major manufacturers like Fender, Gibson, and Gretsch. The gold “K” Line featured the Jazz Special, Artist, Pro, Upbeat,[18] Jazz II, and Jazz Special Bass. Gold “K” guitars used the same hardware as top manufacturers. However, there were truss rod and neck issues.[citation needed]

Although the book contains some good information, it is not well written. In particular the use of poor grammar makes reading annoying. There is also incorrect reference to measurement units. She makes reference to measuring 1/32 or 1/64 of a millimeter. A millimeter is metric, measuring 1/32 or 1/64 are fractions of an inch, not a millimeter. I'm glad it was a free book.

Rolling Stones best electric guitarist list should've been nicknamed the best average guitarist list. I didn't give this guy the time of day because I thought the bucket thing was to cover up how badly he sucks. Turns out it's the opposite. He's just weird. It's too bad the average person doesn't have the capacity to enjoy this type of advanced music.
C.F. Martin & Company is a U.S. guitar manufacturer established in 1833 byChristian Frederick Martin. Martin is highly regarded for its steel-string guitarsand is a leading mass-manufacturer of flattop acoustics. Martin instruments can cost thousands of dollars and vintage instruments often cost six figures. The company has also made several models of electric guitars and electric basses.

With a body shape that looks like it could have been cut out by hand using a saw in your garden shed, this Kay Old Kraftsman Sizzler guitar manages to be crude and quite fantastic at the same time. "Old Kraftsman" was actually a brandname used on Kay guitars sold by Spiegel stores. The maple neck gives it a rather Fender-like appearance, but this is in fact a set neck and not a bolt-on.

I taught myself how to play on a beat-up old acoustic decca my mom let me have. I couldnt begin to guess how old it is, but it must be just that; its serial number is 129! It has a pretty decent sound, but i really should replace the strings. it has 18 frets and marks at 5 7 9 and 11. Theres no pickgaurd, the body is orangish wood with thick finish and the neck is some sort of dark wood. The damn thing gave me headaches when i was learning because the strings were so far from the fretboard and all incredibly thick too. It came with extra strings and medium and heavy picks. I dont think it would be worth too much now, especially in its condition.
The HOF is one of the single best examples of a convergence of price and quality features that we've ever been able to find. While we can't mention pricing in this article, we'd recommend clicking through and checking the retail price on the HOF, then comparing it to the other reverb pedals in this list. As far as value, the HOF is nearly a perfect 10.
The name has a long and involved history that is interwoven with that of the resonator guitar. Originally coined by the Dopyera brothers when they formed the Dobro Manufacturing Company, in time it came to commonly mean a resonator guitar, or specifically one with a single inverted resonator. This particular design was introduced by the Dopyeras’ new company, in competition to the already patented Tricone and biscuit designs owned and produced by the National String Instrument Corporation.
For the last tip/technique, I’m going to shift gears and talk about recording acoustic—upright—bass. This may seem more daunting, but many of the same techniques apply—I’ll mention a few quick items that would be specific to the big box. While the dynamic mics I mentioned above might work fine (especially on stage), a good large-diaphragm condenser would be appropriate in the studio, to capture the high end and air of the acoustic instrument as well as the lows. On stage, the relatively low acoustic volume of the instrument may preclude more distant mic positioning, but you can wedge a small (pencil-type) mic into the bridge, with appropriate foam padding, and this, surprisingly, can often provide excellent sound and much better isolation. 
It should be noted that some bridge assemblies have pre-set, non-adjustable saddle pieces. The Gibson "tune-o-matic" bridge is just one example. On these bridges you will have an overall height adjustment post on either side of the bridge. For these bridges, measure the height at the 12th fret for the low and high "E" strings and make your height adjustment for each side at the respective post. The other string heights will be defined by the bridge assembly.

By and large, time-based effects split the guitar output into two identical signals and momentarily hold one back while allowing the other to play in real time. The two signals are mixed back into one at the output. Usually you can control the length of the delay and the amount of the signal that is affected versus the part that stays "dry" (unaffected). This latter control—found on most effects—is usually called the level control.
Our pick here is the PAC112V version, for a few reasons. First off, the solid alder body offers you the same tonewood you’ll find in a lot of higher end S-style guitars. The maple neck and diecast tuners will feel really premium in your hands, too. But the 112 series further boosts its value with two Alnico V single coil pickups and an Alnico V humbucker. The addition of the humbucker in the bridge position will open up a whole other world of tones for a budding musician, giving the option for both clean, crisp single coil sounds and thick, high-output humbucker growls.
Basicly it is a HD digital sound interface plus with a MIDI controller and footswitch. It is has unique design with different HOST mode and switching MODE to work with the host softwares. We are proud of that it is now maybe the best thing you can find to use on stage with software FX. The special designed analog signal chain mixing with the digital codec give the best dynamic response and sound quality. We did AB with lots of other interface and be so confident on its performance.
As we’ve shown here, a lot of relatively small—and inexpensive (many are practically free)—tweaks can hot-rod your tone and maneuver it to an array of differing ports of call. In some ways, it’s like tossing a handful of dice instead of just two—because the way small tweaks interact can lead to exponential changes in sound. For that reason, my advice is to take it slow and only make a single change at a time to understand what it delivers. Besides, it’s more fun (and less stressful) that way, anyway!
This is a guitar that feels alot like a pre-CBS Fender strat. It has all the tones. If you didn't already know, G&L stands for George and Leo. As in LEO FENDER. The headstock is a little different, but the pickups are great, not Noiseless but definitely not NOISY either. Mine is a physically heavy guitar. It sounds heavy too - in a good way. Still, I can get all the tones I need from all the pickups. I believe that the neck pickup is superior to the Mexican Made Fender Strat. The pearloid pickguard is pretty. These Indonesian made strats sound great. They're made in the same factory as the Squiers but definitely sound different.
I have owned Fender amps and Line 6 amps and while they have been "ok" amps, none of them come close to my newly acquired Mesa Mark V 90watt and 4� - 12 rectifier cab. Amp is super versitile and the time is out of this world. I knew I'd hit the jackpot the first time I plugged up to one. Mark V pairs nicely with my variety of guitars including PRS Holcomb sig, Fender Tele and Strat, Schecter Hellraiser, and Epiphone Les Paul. There's a tone in there for everyone, every guitar and every style of music... you just have to be willing to sit down and get to know the amp. Mesa Boogie is definitely the brand for me so I cast my vote in with them. Great company with quality amps and super friendly/helpful custom service.
Ultimately, be aware that the key to sounding the way you want lies in your hands and your head more than anywhere else. The way a player attacks the strings — the nuance, dynamics, and subtleties of the playing technique — usually has a bigger influence on how he or she sounds than any other single ingredient in the rig. Try to play mindfully, being keenly aware of the variations in sound produced when you simply play the guitar differently, and you will quickly develop an original voice.

Musicians, audio engineers and record producers use effects units during live performances or in the studio, typically with electric guitar, bass guitar, electronic keyboard or electric piano. While guitar effects are most frequently used with electric or electronic instruments, effects can also be used with acoustic instruments, drums and vocals.[3][4]
X-Series: Back and sides constructed from compressed wood fibers (high-pressure laminate or “HPL“) and solid Sitka spruce or HPL top. Due to this construction these guitars are more environmentally-friendly.[citation needed] Models include: DX1, DX1-R, DXM, DCX1E, DCX1R3, 000CXE Black, and 000X1. Some earlier models used ‘Ebonite’ (black Micarta) fretboards, later models use koa or striped ebony. Necks on all models are constructed from Stratabond, a laminated wood product used for decades in gun stocks and hunting bows. Some of the more recent models are made in Mexico.
But is the Fender Deluxe really as good as the name suggests? We certainly think it is! Even though it would be easy to just write it off as an electric guitar for country music, it’s actually really versatile and can be used for any other genre as far as we’re concerned. This is thanks to two vintage noiseless pickup configurations, one on the neck and one on the bridge, and a strat pickup in the middle.
Keep in mind that the year the guitar was built is no guarantee that any individual guitar is in the optimum condition required to handle steel strings. Any Martin should be evaluated with care, and a top that lifts significantly in the bridge area or this is not firm, is a sign that lighter strings should be used. Or that the guitar is in need of attention by a qualified repair person.
Searching for something to give them a boost, in July ’68, Ovation introduced its first electric guitars – the Electric Storm series. Two models were available initially, the Thunderhead and the Tornado. These were f-hole semi-hollowbody thinline, equal double-cutaway guitars with German-made bodies, bolt-on Ovation necks, and Schaller hardware. Most had Schaller pickups with metal covers, a row of poles along each edge, and split, small, black inserts in the middle. Each was available with or without vibrato.
If you’re trying to find one of the affordable acoustic electric guitars from Ibanez, then the PF15 is just what you’re looking for. This guitar has a dreadnought full-size body, a stylish cutaway design, as well as other features which will allow you to enjoy every minute of playing. You also get an attractive Transparent Blue Burst finish to impress your audience.
In our testing, the Fender Champion 20 was the only amp that offered a wide variety of amplifier sounds and special effects while also keeping them all easy to access. Beginners can get a great sound easily and experiment with different effects without having to invest in separate effects pedals. Experienced players can get most of the sounds they want with nothing more than a guitar, an amp, and a cable.

Immediately you can see that this unit is on the larger side, measuring 25 inches (63.5 cm) across, and weighing about 11 lbs (5 kg). If you’re concerned about portability, we noticed one of the most purchased items together with the HD500X is this case, which comes highly recommended and will keep your multi-effects pedal safe during transit and storage. The Line 6 POD HD500X itself has superb build quality. It has a very nice metal chassis, and heavy duty construction. The build quality probably doesn't get much better than this in a multi-fx unit (we say it is a step above the Zoom G3X). We won’t spend a ton of time talking about the inputs/outputs and controls available on the Line 6 POD HD500X, since you can very easily discern that from photos of it. We will say that of all the multi-effects pedals on our top 5 list, this is the most robust. The inputs/outputs cover above and beyond what you probably need. You’ve got your basic inputs and outputs, USB 2.0 so you can use it as a USB interface and for DAW integration, MIDI in/out/thru, FX send and return, AUX input, balanced XLR outputs, integrated mic preamp, and more. In short, however you want to integrate the HD500X into your bedroom, music studio, or live setup, there’s a very good chance you’re covered.
The Cordoba C7 spruce-top has a natural finish, complete with rosewood back, sides, fretboard and bridge, and the traditional looking inlay that Cordoba is known for. Plus, there are the Savarez Cristal Corum high-tension strings that come with it, which give the guitar its clear, clean sound. Of course, you might want to change to another set of nylon strings, should you wish it, depending on the sound you truly want.
BAJAAO bring to you the best and extensive range Electro Acoustic Guitars also known as the Acoustic Electric Guitar or Semi Electric guitar in layman terms from all over the world. Versatile in design, the electro acoustic guitar is known for its smooth sound and powerful projection. At its core, an acoustic-electric guitar is acoustic in style fitted with a pickup device allowing it to be plugged into an amplifier, a number of effect pedals or played on its own for a more intimate sound. Heard in basically every genre of music, these guitars are indispensable in almost any modern band setting. In acoustic-electric nylon string guitars, piezoelectric pickups and microphones are used because magnetic pickups are not capable of picking up vibrations of non-magnetic materials. The design is distinct from a semi-acoustic guitar, which is an electric guitar but with the addition of sound chambers within the guitar body. Buy the best Electro Acoustic Guitars online with with the best and affordable price in India. Make your shopping experience a wonderful one with us.
Between 1974 and 1984, production of Gibson guitars was shifted from Kalamazoo to Nashville, Tennessee. The Kalamazoo plant kept going for a few years as a custom-instrument shop, but was closed in 1984; several Gibson employees led by plant manager Jim Duerloo established Heritage Guitars in the old factory, building versions of classic Gibson designs.

Deco Tape Saturation & Doubletracker is a unique effects pedal that allows for a wide variety of tonal possibilities.  You can place Deco near the beginning of your signal chain and use the Tape Saturation as a light overdrive.  Or, you can place Deco at the end of your chain, use lower Tape Saturation settings, and provide your entire signal with the tape-like warmth, compression, and added low end harmonics.

When you're in the market for an instrument, whether it's brand new or new-to-you, our impressive selection gives you plenty to choose from and we'll be happy to help you find the right fit. Maybe you need some equipment for a few gigs or a short tour? Our rentals department can hook you up. There are even lessons and free workshops here to discover, so you can always learn more about music no matter your skill level. For all the details, you can drop by to visit us in-person or give us a call.
Another important point I want to add here is - if you are on a budget, do take a look at models in higher price brackets. Why? The simple reason is, it will make you aware what a good guitar looks like. The expensive ones usually have better sound quality, better looks and it is more comfortable. It will help you grow along with the guitar. Always buy the higher priced guitar in the range that you can afford.

The electric guitar was essentially born in 1929—long before the advent of rock and roll music. The first commercially advertised electric guitar was offered that year by the Stromberg-Voisinet company of Chicago, though it was not a smash hit. The first commercially successful electric, Rickenbacker’s “Frying Pan” guitar, didn’t kick off rock ’n’ roll yet either, but it did inspire competitors to jump into the electric guitar market. Invented in 1931, the Frying Pan had an electromagnetic pickup made out of a pair of horseshoe magnets placed end-to-end to create an oval around the guitar’s strings, with a coil placed underneath the strings. The pickup, a device that converts the strings’ vibrations into electrical signals that can be amplified, was bulky and unattractive, but it worked. The commercial version of the Frying Pan was a hollow cast-aluminum lap-steel guitar, and wasn’t an immediate hit beyond some Hawaiian, country, and blues musicians. It differs from the traditional Spanish-style guitar in that it is played horizontally, on a stand or in the player’s lap, and has a sliding steel bar that can be moved along the frets for a gliding effect.

In May ’71, Ovation tried once more. It introduced the K-1217 Typhoon V bass, about which no information is available, but based on the Eclipse, the difference may have been pickups. The K-1235 Eclipse was also introduced. This was a guitar offered only in a black finish that looks somewhat like graphite. It had chrome hardware, no binding, dot inlays, three-way select and two volume and two tone controls. The pickups had metal covers with black inserts and a single blade-style pole. In June ’72, all Electric Storms were discontinued except the Tornado and Eclipse, which made it another half year, until January ’73, by which time the Electric Storm had subsided into quiescence.
Discrete models describing the low frequency behavior of stringed instruments have appeared in the technical literature for more than 25 years. These models are very useful in understanding the nature of acoustic-structural interaction, but only when they are correctly tuned to match the measured response of a particular instrument. The tuning process is easiest when FRF measurements are made... [Show full abstract]
Adjust the volume and tone and engage the gain when you want to bust out some distortion riffs or throw your headphones in via the 6.3mm Jack headphone output which also doubles up as a preamp out. Enjoy silent practice anywhere or hook it up to your audio interface for studio recordings. A powerful little amplifier relied upon by guitarists when inspiration strikes. At under £30 it’s actually an essential purchase for musicians and one of the best music gifts ever – it’s certainly cheap, but it certainly doesn’t suck! Available in a range of different colours and as a double stack for extra volume.

For example, bass guitar frequencies are on the relatively low end of the tonal spectrum. However, plucking a bass string can create a sudden, short burst of high and mid-frequency sounds. You need your bass amp to be loud enough to make those low-frequency sounds strong and audible in the mix, but you don’t want to flatten your band mates or blow out your speakers by sudden pops of high-frequency sounds.

The "Chrome Edition" harmonica is also based upon the MS reed plates. Featuring a crystal glass comb and specially engraved chrome-plated anniversary cover plates. The bottom cover plate has the serial numbers from 1 to 1857. It is also packaged with an anniversary booklet. The "Standard Edition" model features a clear acrylic comb and the top cover plate is specially engraved.
My rule of thumb, whenever possible, is drive the input and route the modulation. I.E. - I put compression, over drive, distortion, fuzz, and wah/filter effect on the input; and then I route flange, phase, chorus, and delay through an effects loop. I do this for a couple of reasons - 1.) I don't have 15 effects ganged together hitting my input which can effect tone, clarity, and volume; and 2.) I can shape the tone and dynamics of my guitar going the amp's input while maintaining definition, tone, and volume to my modulated effects through the buffering provided by an effects loop.
Electric guitars have come a long way since then, and today you’ll see many different designs. But you can still find big hollow-body jazz boxes that hearken back to those early days in the lineups of many manufacturers. They’re best suited for jazz players looking for a warm, woody sound. Of course the technology has improved greatly in the past eighty years, but these instruments still have a nice vintage vibe. You’ll sometimes see these instruments referred to as semi-acoustic.
Of course, this top-down lecturing is all very abstract without examples. Let me give you the worst case scenario. My school talent show, 2008. Two friends of mine performED an ambitious but utterly inappropriate Metallica cover in front of the other students, their parents and the faculty. It was excruciating. Although the solos (presumably the only thing they had bothered to practice) were technically flawless, the whole song was undone by their terrible rhythm. The timing of the song became displaced, the chords were so badly fingered that it was difficult to hear the riff and consequently the whole performance fell apart. They looked like morons. They had sacrificed learning basic rhythm and paid the price. Make sure you don’t do the same.
A selection of makers within the high-end, hand-built crowd of today do offer variations on the opamp-based template discussed above. Blackstone Appliances bases its Mosfet Overdrive on a discrete transistorized circuit centered around, yes, mosfets, and Klon’s Centaur pedal uses… well, who the hell knows? They cover the entire circuit board in epoxy goop to keep the cloners at bay, but this expensive overdrive certainly sounds different. Other popular boutique overdrives are found in the Barber Electronics LTD pedal, the Crowther Audio Hot Cake, and the Fulltone OCD.
The Hi-Flier guitar, which was possibly built in the Matsumoku factory, underwent multiple phases during the course of its production. Each of the Hi-Flier’s four manufacturing phases came with a variety of feature changes, ranging from simply switching the color of the pickguard to actually fitting the guitar for humbuckers rather than the P90-style pickups it originally came with.
The Hal Leonard Folk Harp Method is a comprehensive and easy-to-use beginner's guide, designed for anyone just learning to play folk harp. Inside you'll find loads of techniques, tips, and fun songs to learn and play. The accompanying CD contains 56 demo tracks that cover most of the music examples in the book. Covers: the harp and its parts; sitting with the harp; hand position and finger placing; key signatures and meter signatures; scales and arpeggios; the I-IV-V chords; ostinatos and slides; many classic folksongs; and much more!.
EQ (Equalizer) – A frequency-based effect that allows you to boost or cut frequencies along the audio spectrum. Graphic EQ pedals such as the GE-7 and GEB-7 have faders for each frequency band that you can move up or down to boost or cut the frequency. EQ pedals can be used to tackle problem frequencies such as mid-range honk or to give a bass boost or add some high end sparkle. Alternatively you can use EQ to create interesting tones such as emulating a small radio by rolling off the bottom end and boosting the high mids.
The Effect:Distortion is one of the most popular and desired guitar pedal effects, especially among rock, hard-rock and metal players, The Kinks, Jimmy Hendrix, Metallica, to name a few. Prior to the introduction of effect pedals on the market, Distortion was mostly achieved by forcing an overwhelming amount of electricity passing through a guitar amp’s valves. Nowadays this is no longer necessary. Arguably one of the most famous and newbie friendly option and at the same time prime example for a distortion pedal is the classic Electro-Harmonix SOULFOOD.
I have a 12-string Lyle in really good shape. Bought as a b-day present from me back in late 1970's from a pawn shop. I need to take it to a luthier to have it set up better, but it sounds really good. Just right now the action is a little high, but not that much wear. For a long time, I put it away, finding it hard to chord as a relative newbie back then. But now, I am more than ready. It does say it was made in Korea ~ which makes it seem a little more rare. The sound is still great or maybe even better! Wish I knew what it was worth, but I hope the guy I find to set it up will know more.

List of electric guitar brands that include the most reliable models available. Electric guitar brands include those from major manufacturers of musical instruments, including Yamaha, Gretsch, Gibson and more. This list answers the question, 'What are the best electric guitar brands?' Users looking for a new guitar will want to research a variety of different brands to find the one that best suits their needs, based on function and features.
Power chords are one of the staples of rock music and one of the most important guitar chord types you need to have in your toolbox. They are important to learn for a few reasons: They’re easy to play They’re used a TON in many popular songs and are very versatile. They’ll help broaden your repertoire of guitar sounds / styles. This post will walk you through step-by-step what a power chord is, how to play them and what songs you can learn to start practicing them. What are Power Chords? Whether you play an acoustic or electric guitar, you are going

I'll second the neck comment, conditionally. My first guitar was a hand-me-down Monterey archtop acoustic that had been my uncle's, and it have a sharp V neck. Out of nostalgia I bought another Monterey on eBay and its cross section feels like a tomato can lying in my hand. After a refret it plays smoother and easier than anything that fat has a right to. The original frets..., not quite.
I was a little concerned buying a guitar on Amazon. I had not even played a sample on the Gretsch acoustic. I've played Martins, Fenders, Washburns, etc. but never heard of the 'Gretsch'! It arrived within a few days of ordering with the case I ordered too. I had it delivered to my office so that it wouldn't be sitting on my porch until I got home. I opened the box to examine the guitar and co-workers asked me to play something. As I was tuning the white Gretsch I broke a string, so playing it for my friends was not going to happen. When I got home I re-stung the guitar and as I was tuning it I was not very impressed. I like the look but come on we purchase a guitar to play! After it was tuned I began to play a few chords and licks.
{"eVar4":"shop: shopbybrand","eVar5":"shop: shopbybrand: harmony","pageName":"[gc] shop by brand: harmony","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop by brand: harmony","prop1":"[gc] shop by brand: harmony","prop17":"sort by","evar51":"default: united states","prop10":"brands","prop11":"harmony","prop5":"[gc] shop by brand: harmony","prop6":"[gc] shop by brand: harmony","prop3":"[gc] shop by brand: harmony","prop4":"[gc] shop by brand: harmony","channel":"[gc] shop by brand","linkInternalFilters":"javascript:,","prop7":"[gc] site section"}
Fingerboards vary as much as necks. The fingerboard surface usually has a cross-sectional radius that is optimized to accommodate finger movement for different playing techniques. Fingerboard radius typically ranges from nearly flat (a very large radius) to radically arched (a small radius). The vintage Fender Telecaster, for example, has a typical small radius of approximately 7.25 inches (18.4 cm). Some manufacturers have experimented with fret profile and material, fret layout, number of frets, and modifications of the fingerboard surface for various reasons. Some innovations were intended to improve playability by ergonomic means, such as Warmoth Guitars' compound radius fingerboard. Scalloped fingerboards added enhanced microtonality during fast legato runs. Fanned frets intend to provide each string with an optimal playing tension and enhanced musicality. Some guitars have no frets—and others, like the Gittler guitar, have no neck in the traditional sense.