One important thing to keep in mind about effects pedals is that the signal is doing a lot of work going through the complex electronics in them, and some effects play better as inputs for others. This all means that the order of your pedals does matter to some degree, depending on which effects are in the lineup. You can, of course, experiment to see how different orders affect the sound and that can be part of creating your own signature effects profile. But as a rule of thumb, here’s the basic order you should follow for your first foray into effects chaining:
You can simulate any sound of three pickup guitar with two pickup guitar and vice versa, the only problem is getting it with proper wiring or customizing it. Even they will not sound the same may be close enough for your application or even better. And don't forget about potentiometers problem. The 250K potentiometer will cut some frequencies from humbuckers while 500K make singles brighter than they are by default. It may be not a problem or critical to choosing favorite tone :D

Even when the bass track(s) are well-recorded, and sound good, you may want to enhance the bass tone for mixdown with your favorite bass-friendly plug-in processors. Besides the obvious EQs and compressors, there are many distortion processors and amp sims out there suitable for bass. Sometimes a simple tube-warming effect is all you need to add a little subtle fatness, like the many plug-ins that simulate slight tube drive or tape saturation. I always liked the Tech 21 SansAmp on bass, and Pro Tools includes a well-modeled plug-in version of that unit. Most of the popular guitar amp modelers also include options that can add some nice grit & girth to clean bass tracks, including Softube’s Bass Amp Room and Logic’s built-in B.A.D.—Bass Amp Designer—which, like most bass amp sims, includes models of classic bass amps like the Ampeg SVT and Fliptop, along with modern bass amp & cabinet emulations. Any of these can add that finishing touch to a good bass part, and there are many freeware options as well, for those on a tight budget.

In 1883, a german immigrant named Frederic Gretsch started a small instrument manufacturing company in Brooklyn, New York. On a trip to visit home in 1895, he died unexpectedly, leaving the company in the hands of his 15-year-old son, Fred. The company flourished for generations, especially due to the popularity of their hollow body guitars with rockabilly, blues, and jazz musicians. In 1967, however, the brand began to falter after the Gretsch family sold to then music industry giant Baldwin. In 1985, Fred W. Gretsch bought the company back from Baldwin and began restoring it to its former glory – coinciding with the rise of one of their most prolific artists, Brian Setzer of the Stray Cats. Today, their guitars, like the USA Custom Shop White Falcon pictured above, are used by a wide array of musicians from all walks of life, including Billy F. Gibbons of ZZ Top, Tim Armstrong of Rancid, Band of Skulls, and Portugal. the Man.
The AF75 also has an ART-1 bridge and a VT60 tailpiece for increased resonance, improved tuning stability, greater sustain and an enhanced tone. It is also equipped with Classic Elite humbucking pickups at the neck and bridge, producing a rich and nuanced tone with just the right low-end heft. Tone shaping is an easy affair with the Sure Grip III control knobs, which are designed for non-slip, precise control.
Because driving the power valves this hard also means maximum volume, which can be difficult to manage in a small recording or rehearsal space, many solutions have emerged that in some way divert some of this power valve output from the speakers, and allow the player to generate power valve distortion without excessive volume. These include built-in or separate power attenuators and power-supply-based power attenuation, such as a VVR, or Variable Voltage Regulator to drop the voltage on the valves' plates, to increase distortion whilst lowering volume. Guitarists such as Eddie Van Halen have been known to use variacs before VVR technology was invented.[specify] Lower-power valve amps (such as a quarter-watt or less)[citation needed], speaker isolation cabinets, and low-efficiency guitar speakers are also used to tame the volume.
There were at least three different versions of this guitar with differing knobs, fingerboards, control plates, cord mounting, and trim. One even had a nice rosewood fingerboard with dots. This version was the most monochromatic of the bunch, I suppose. It cleaned up really nicely for these pictures. Okay, so it's an ugly little spud. My wife describes this guitar as "so ugly it's cute," and she fell in love with it in the store for that reason. I like that.
However, if you want a small guitar that will give the quality of sound you might expect from a larger guitar, or if you are considering this style as the first beginner guitar for a child or student, you may want to consider other models that are more typical of a guitar suitable for learning, recording or for growing and developing better skills.
Shop Hourly Rate is $60.00 per hour. Since each guitar is unique, prices quoted are estimates and may be adjusted based on actual time involved. A final price will be submitted prior to actual work and price may need to be adjusted in the case of repairs that get more involved as the work progresses. (Please see the article on the 1975 Gibson Hummingbird for a good example of this.)
So, to make a successful guitar company, you need to beat the best brands out there. But how would you do that? Brands like Fender and Gibson advertise themselves as the original inventors of the two most popular electric guitar models, the Stratocaster and the Les Paul. This is one of their biggest selling points. Unfortunately, you can’t reinvent something that’s already been invented, hence you can’t really beat them at brand name, especially when you’re starting a guitar company. You have to try to beat them at quality, price and novelty (i.e., introducing something new that improves a guitarists experience). Eventually, you’ll have to get some artists to try out your models and sign deals with them. If you get all of this right, I think you should be able to make it big.

Eventually, silicon transistors replaced germanium ones, helping to combat the inconsistent sounds of the germanium version (each circuit varies, and they were often affected by hot temperatures). Silicon completely changed the distortion, making it brighter, edgier, and more aggressive, as exemplified by the famous Electro-Harmonix Big Muff. The later introduction of the integrated circuit provided even more stability. Digital emulators can now universalize effects in a standalone unit. Materials don’t lie, however; when compared to their analog ancestors, the digital units lack the unique wildness of the germanium effect.
Double-neck (or, less commonly, "twin-neck") guitars enable guitarists to play both guitar and bass guitar or, more commonly, both a six-string and a twelve-string. In the mid-1960s, one of the first players to use this type of guitar was Paul Revere & the Raiders' guitarist Drake Levin. Another early user was John McLaughlin. The double-neck guitar was popularized by Jimmy Page, who used a custom-made, cherry-finished Gibson EDS-1275 to perform "Stairway to Heaven", "The Song Remains the Same" and "The Rain Song", although for the recording of "Stairway to Heaven" he used a Fender Telecaster and a Fender XII electric twelve-string. Mike Rutherford of Genesis and Mike + the Mechanics is also famous for his use of a double-neck guitar during live shows. Don Felder of the Eagles used the Gibson EDS-1275 during the Hotel California tour. Muse guitarist and vocalist Matthew Bellamy uses a silver Manson double-neck on his band's Resistance Tour. Rush guitarist Alex Lifeson is also known for using double-neck guitars in the live performance of several songs. In performances of the song "Xanadu" during the band's 2015 R40 anniversary tour, Lifeson played a white Gibson EDS-1275 double-neck guitar with six-string and twelve-string necks, while bassist Geddy Lee performed with a double-neck Rickenbacker guitar with four-string bass and twelve-string guitar necks.
This guitar follows after the tried and tested formula of old Stratocaster design, from the double cutaway alder body to the bolt-on maple neck, down to its triple single coil pickup configuration. The scale length follows after traditional builds at 25.5", while the neck profile (modern C) and narrower nut width of 1.65" makes this guitar viable for modern players. While it doesn't have vintage voiced pickups, the default pickups are not so bad either, and will give you the distinctive Strat tone that almost everybody loves.

The Dean Vendetta pack offers a sharp looking metallic red super Stratocaster style guitar with dual humbuckers, a tremolo bridge for fun dive tricks, and a 24 fret neck. This is perfect for players that want to start learning lead guitar as soon as possible. The neck is quite fast for a guitar in its price range. Also included with the purchase is a 10-watt practice amp, gig bag, instrument cable, picks, a tuner, and a fairly comfortable strap.

I'm no musician, know very little about guitars, but I think I stumbled on to a great deal. The predicament we faced last Christmas was that my two nieces, ages just 7 and 5, both fell in love with a toy "music" setup consisting of a plastic "guitar" and a fake microphone. I won't say the famous girl-toy-brand name it was marketed under but it was pretty much a collection of junk. The "guitar" had a few buttons on it to make noise... it would have been broken and tossed away inside of a week. And here in Costa Rica - a price of 34,000 colones or roughly $70!

1. Intonation: I have a brand-new Epiphone LP that will not completely intonate on the G, A, and Low E. Fretted notes remain sharp. I have replaced the factory strings with new Ernie Balls and tried every trick in the book to move the saddles as far away from the neck as possible. Many LP owners have this problem. Other than returning the guitar to Guitar World, my only other option is swap out the factory bridge with a wider one. You mention the latter option in one of your early comments, and I've decided to try it. I just bought a Gotoh one online. Hopefully, that will solve the problem.
Here's a fresh one from the JVG Vault... vintage tone much like an old classic Martin Acoustic has some wear and has the "feel" just feels great in your hands and plays & sounds wonderful. Good volume and rich sounding lows and very nice.. condition rated at a solid 8.5 / 10 or better no cracks no repairs and plays nicely with original nut & saddle still in place , optional change nut & saddle & set up add $80.00. Please SEE MORE FULL SCREEN HIGH RES PICTURES HERE:
The National String Instrument Corporation for manufacturing these louder guitars was founded probably in 1927, in Los Angeles, by John Dopyera, George Beauchamp, Ted Kleinmeyer and Paul Barth, when production and advertising began. The company was officially certified as a California corporation in 1928. For a detailed accounting of those early years, I recommend Brozman’s book, The History and Artistry of National Resonator Instruments (Centerstream Publishing, Fullerton, California, 1993). This is a horribly confusing relationship, so stick with me; we’ll try to put it right.

Jump up ^ Miller, Jim (1980). The Rolling Stone illustrated history of rock & roll. New York: Rolling Stone. ISBN 0-394-51322-3. Retrieved 5 July 2012. Black country bluesmen made raw, heavily amplified boogie records of their own, especially in Memphis, where guitarists like Joe Hill Louis, Willie Johnson (with the early Howlin' Wolf band) and Pat Hare (with Little Junior Parker) played driving rhythms and scorching, distorted solos that might be counted the distant ancestors of heavy metal.

This one SOLD pictured has been SOLD OUT: This is one of my favorite vintage Alvarez guitars and is always truly a very good surprise just how great these sound / impressive and I have collected more than several over the years of this very model vintage era lawsuit guitar in AMAZING Condition. Here we have a wonderful and very clean example of a Vintage Japanese Acoustic its a late 1970's great Alvarez 5056 with the most intricately detailed inlay work everywhere on the body.... the front & back in Abalone & the fingerboard is rich - dark and wavy grained it looks to be Brazilian Jacaranda Rosewood and has the Gorgeous Tree of Life in mother of pearl & abalone inlayed into the rich rosewood fingerboard WoW!,even the bridge has Mother of pearl inlaid, (you should have a real good look to come to your own conclusions if its something you like ) and the frets are in very good original condition... action is very good nice & low adjustable either way with no buzzing anywhere on the fretboard real nice playing example here folks.. The finish has a natural golden patina as seen to it and this guitar is strikingly beautiful. No cracks, no repairs, very good - excellent vintage used condition and is JVG rated at 9/10 WoW!... She's very EZ on the eyes to say the least and a premium performer this vintage piece has had over 33+ years to age and mellow and was a one owner California guitar in above better than average condition... no splits or cracks or separations or repairs ever... I believe this to be the cleanest best playing vintage 5056's we have ever had in JVG or seen for that matter. This one is a real pleasure to play! HERE IS A LINK TO CUT & PASTE TO SEE MANY MORE PICS OF THIS INSTRUMENT: .
Flawless build, the action is set up so well I don't see any need to tinker with anything. Pulled it out of the box, tuned it and strummed a few chords, then set it aside for 24 hours. Re-tuned it the next day and it has stayed in tune. I cannot find anything amiss or out of place on this one. Per the serial number, this is a 2015 Indonesian build. The wood is simply perfect in appearance and the tone is outstanding for a thinline. Yeah, I am happy with this one. Recommended.
Wow, didn't expect a budget-priced instrument to perform this beautifully! I had planned to use this as an introduction into nylon-string (from electric), then upgrade to a better (i.e. more expensive??) model. That won't be necessary! The NTX700C is absolutely perfect for me and will remain the nylon-string guitar in my stable. I am a professional solo jazz guitarist and ventured into a nylon-string for my Brazilian jazz set. Being an electric player, the transition with this model has been much easier than a traditional classical. The onboard electronics are great with my Bose L1 system. I have the cedar top, and the tone is very mellow, and already opening up with only three weeks of playing.
Description: Body: Maple & Poplar & Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Maple & Poplar & Maple - Neck Attachment: Glued - Neck Wood: Maple - Neck Construction: 1 Piece - Fingerboard: Rosewood - Binding: Cream - Frets: 22 - Inlay: Pearloid block - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: ABR-1 - Cutaway: Double - Hardware: 2x Volume Control, 2x Tone Control, Grover Tuners - Pickups: Burstbucker 1/Burstbucker 2 - Pickup Configuration: H-H - String Instrument Finish: Faded Cherry - String Instrument Accessories: Hardshell Case, Certificate of Authenticity - Made In: America

A 6 stringed guitar, black satin in color. It is gloss finish and comes without a case. The body is made from Mahogany and the neck from the Flamed maple. The guitar consists of tone,volume and 3 way pickup switch. It was introduced alomost 20 years ago and includes all the charm present in its cousins from USA . The device can be acquired with as little as INR 19,755  and more details can be found at:
Now you should have all you need to assemble your first effects pedal. Make sure you have a clean, well-ventilated area to work. Wash your hands before you start. If you like, wear some conductive nitrile gloves. Avoid handling components any more than necessary. Contaminants on the components and PCB will make them harder to solder and can cause reliability problems. Certain IC’s can be damaged by static electricity from handling. Solder is hot and creates dangerous fumes so be careful. Follow the instructions carefully, in particular making sure you insert components in the correct places and the correct way around. Many components look alike and some are polarity sensitive, so take your time to get it right. Solder one pin of a component and then double-check it before soldering the rest. It’s much easier to move or remove a component with only one lead soldered to the board.
The first thing that you’ll notice is that the PR5-E is a florentine style guitar, which means that it has that fantastic looking cutaway with a really dramatic horn. This gives you nice access to the upper frets while retaining some resonance. The result is some really nice tone for such an affordable guitar. What’s more is that it’s a slimline design. It is an incredible sounding instrument.
The octave pedal raises or lowers your pitch an octave. This makes a huge sonic impact as soon as it is heard. This pedal will make your guitar sound huge, broad and bass-rich or fierce and piercing - even both. It's best to look for a pedal with a “mix” knob, so that your original tone is not completely lost. One step and you can change the direction of the riff or the entire song. This effect was used extensively by Jimi Hendrix in combination with a fuzz tone, while more modern users include Tom Morello and Jack White.
Straight away, we have to talk about how good this guitar sounds. Lots of low-end and mid-range acoustics tend to do one tonal area well, but the Martin DRS2 does an awesome job all round. It’s got deep, booming lows, while the highs remain nice and crisp. And of course, all of this is available acoustically or electrically in the dreadnought cutaway acousticelectric guitar.
Just like Fender, Epiphone – the Gibson subsidiary – know a thing or two about budget acoustics, and this DR-100 (reviewed in full here) more than proves that! With a range of finishes, the DR-100 features a classic dreadnought body shape, with back and sides made from laminated mahogany, with a select spruce top, and black pickguard sporting Epiphone’s iconic E logo.
Now, as others have mentioned, there is a switch that controls which pickup (or pickups plural) you want to use at any given moment. Seeing as each pickup is placed at a different point under the strings, the vibrations are slightly different. The closer the strings are to the bridge at the bottom, the more 'narrow' and intense the vibrations get. Thus the current generated from the magnets lead to different sound characteristics.
As successor to the Bogner Triple Giant, the Fish is a pre-amp with a legendary status, due to it’s unique character and it’s 4-channel configuration. Originally introduced in 1990, the unit was limited to 250 pieces, and is a rare find now-a-days. But thankfully, Bogner decided to reintroduce the Fish, featuring a “Country”, “Shark”, “Strato”, and “Brown” channel. Just like the original, this amp can take on just about any style you throw at it!
Enter the polyesters and the polyurethanes. These plastics can be made into synthetic resins which harden after application the guitar body, making them more durable than nitrocellulose finishes. In some cases, UV light can be used to initiate the curing process of the resin, making the finishing process much quicker than the application of nitrocellulose lacquer.

Ibanez, a guitar and bass manufacturer, came to prominence as a result of music legends like Steve Vai and Joe Satriani using this brand. These guitars provide an exceptionally uniform neck action, a highly versatile tone, and top of the range pick up configuration. One of the main reasons that this brand gained popularity was the effective tone from cheap and mass-produced instruments. Heavy music is what they excel in, and metal enthusiasts have been loving Ibanez for decades now. They manufacture guitars for every style and genre. The most iconic model is the RG, but S series is also loved by all. They are also the makers of the 7-string guitar, with the first model Universe being made in the year 1990.
Their designs do not require them to have comparator inputs as with solid-state amps. The small amount of negative feedback in valve amps is only required to provide damping to the speaker. Valve Amplifier Design From physics we know certain things must be a particular order and size to be efficient and this is acutely so with valve amps. 60Watts is the minimum power capacity for an amplifier to bring quality speakers to life with full fidelity.
If you’re just starting out, our new electric guitar for beginners may be more suitable for you. Otherwise, let’s get going on our picks (although it was tough to stick with only 10 models). If you want to practice or perform without wires, you can also look into a wireless system for guitars. Be sure to check out our best acoustic guitars article if you want a companion, or if you need extra gear, we have guides for those as well.

Martin flat top guitars were made in various sizes. The bigger the guitar body, the better and more collectible the guitar. This is why guitar body size is so important to identify on a Martin flat top guitar. Starting in October 1930, Martin stamped the guitar body size right above the serial number inside the guitar. This makes identifying body size on October 1930 and later guitar very easy. For flat top guitars made before October 1930, the easiest way to figure out the body size is to use the flat top guitar body size chart below. Body sizes, pretty much from smallest to biggest, include O, OO, OOO, OM, D.
Fender, or the Fender Electric Instrument Manufacturing Company, as it was properly known, was started in 1946, in Fullerton, California, by Leo Fender. The early designs effectively wrote the book on the solid body guitar manufacture; his approach of simple guitars using quality parts, easily assembled (most specifically the replaceable neck) proved an immediate sucess. Guitars like the Fender Stratocaster, Telecaster, Jaguar and Precision bass have barely changed since their very first inception; Fender simply got it right first time round.

This beautiful wood is not a very common tonewood for the construction of a guitar body, but you may see it more commonly in neck construction. However, it has been done to build a guitar body, and it was done well on the famous Gibson J-200 that the Epiphone EJ-200SCE also imitated. It’s a very solid, hard, and dense wood that has amazing sound punch and bright tones.

I ordered this for my 6 year old nephew for Christmas. He wanted one because I had just recently bought my 3rd. I thought a smaller one would be nice for him to start learning. Just opened the box and the amp doesn’t work! At all! Light turns on but nothing else happens! Hooked guitar up to my own amp and it sounds nice so it’d definitely not the guitar or cords fault. Trying to get a replacement but no luck.
Most beginners find that during the process of learning (after a year or so) you will figure out your own sound. You will naturally be drawn to music that features guitar in it, and great guitar parts. So what usually happens is that your own musical tastes will change and with this change the type of instrument that suits your sound the best will also change. So when you’re ready to take the next step, you will have a much better idea of what you really want.
At its core is a combination of solid spruce and maple, which gives it a subtly brighter tone when compared to conventional spruce and mahogany body acoustics. To retain as much of the guitar's acoustic body as possible, Epiphone equipped the Dove Pro with discrete Fishman electronics, with controls that are mounted on the underside of the sound hole.
Here we have yet another fine 1971 Yamaha FG75 made in Japan Nippon Gakki Red Label Grand concert like Gibson LGO-1 but sounds better for less New Arrival: Be sure to ask for "Clean Boy" This example is just like our other 71 FG75 Nippon Gakki but this guitar is much cleaner and is JVGuitars rated in very good + condition- Excellent vintage for a 42+ year old Vintage Red Label Nippon Gakki FG75 .. its one of the nicest we've seen, this baby makes an excellent Parlor style guitar thats fun to play because of its good action, and it sounds absolutely great... upgraded to Martin bone Nut and compensated saddle and upgraded fancy bridge pins .... for a good volume transfer and superior tone over the old plastic parts,,,, we dressed the frets as well. not a crack anywhere to be found, great vintage patina but no structural damages or abuse or neglect this instrument has been well taken care of as one can tell from its condition and playability ... this one plays very nicely and is ready to enjoy .... for a song Original Specifications: - Year(s) Sold: 1968-1974 - Top: Spruce- Back / Sides: Agathis - Neck: Nato - Fingerboard: Indian Rosewood - Bridge: N/A - Notes: Folk Guitar Classic Type - Upper Bout - 11-1/8” - Waist - 9-5/8"- Lower Bout - 14-5/8" Ok so thats what the official specs are but here is what we se and have seend with 2 other fg75;s we have had, one I had to refinish its back and when sanding off the mahogany finish it was blond flamed maple sides and back,,, as this one surely looks to be just look at that flamed back and sides this example is kind of special looking. She;s got it going on just check her out. Yamaha Nippon Gakki guitars are highly respected at being well made and of great value and after 40+ years this example has stood the test of time and is still a formidable player you can compare its sound to a much more expensive guitars tone they are simply wonders to find one this nice is RARE… get her before she’s gone. Any questions or to buy it contact Joe: Thank you for your interest..

DADGAD was developed by Davey Graham in the early 1960s when he was travelling in Morocco, to more easily play along with Oud music Among the first to use this tuning were the folk-blues guitarists of the 60s like Bert Jansch, John Rebourn, Martin Carthy, and John Martyn. It was many years later in the 1970s that it became established for accompanists of traditional music, predominantly Scottish and Irish. Due to this popularity it is sometimes referred to as "Celtic" tuning, although this is misleading given it's origin and it's primary early use in a quite different field of music. Often vocalized as "Dad-Gad", DADGAD it is now common in Celtic music. In rock music, has been used in Led Zeppelin's "Kashmir".[8] Pierre Bensusan is another noted exponent of this tuning. The post-metal group Russian Circles also employ this tuning, and also plays it in the form of all the notes becoming a half-step down: D♭-A♭-d♭-g♭-a♭-d♭'. Three down-tuned variations are used by the band Sevendust: A Drop C variation, or C-G-c-f-g-c'. (used on the song "Unraveling"), a Drop B variation, or B'-F♯-B-e-f♯-b, and a Drop A# variation, or A♯'-F-A♯-d♯-f-a♯. Neighboring tunings D-A-d-e-a-e' and C-G-c-d-g-a have been used by Martin Carthy. Also D-A-d-a-a-d', was used by Dave Wakeling on the English Beat's 1983 "Save It For Later".
#A1056:Another super rare piece from Guitars West! This little number found its way across the pond and onto our doorstep. A very early VamPower 70's 100 watt P.A. 6 channel input head. With speaker channels, one 4 ohm-100w-#1 & 2 input, one 8 ohm-100w-#3 & 4 input, one 15 ohm-100w-# 5 input, two 8 ohm-50w-# 1 & 2 input, two 15 ohm-50w-# 3 & 4 input.
This Yamaha Pacifica features a Strat sound that is very good, especially since the humbucker can be tuned into a single pickup by lifting up on the tone control. Like with every other strat, it has a five-way switch which allows the player to select the bridge pickup, the bridge+middle pickups, the middle pickup, the middle+neck pickups, or just the neck alone. In the event that you are tired of the strat sound and you would like to return to Led Zeppelin, simply flip to the humbucker and get set to go!

I skimmed ahead and quickly realized that, at last, someone has written THAT GUITAR BOOK that we are all looking for when we start out but that no one seems to have written yet but that you hope to write someday when you finally figure out what you are doing so that you can help others and prevent them from wasting so much time and money and hopes....(takes a breath)
this is literally the worst piece of cow dung in the industry. I wouldn't even call it a guitar, it's so poorly made. Management, especially the CEO, don't care a bit about quality, the only thing that matters is their unrealistically high production numbers. the production processes are so archaic they are amateur, and they have the audacity to call it the worlds finest guitar. all of this stems from the CEO and his manic psychotic neurotic management style (he has to sign off on EVERYTHING: new hires, transfers within the company, promotions, raises, budgets, any funding for new parts or machines.
There’s no disguising what the Jackson Pro Series DK2 Okoume is meant for: shredding. From the tonewoods to the construction to the feature set, everything on this guitar is designed to bring the best out of lightning-speed solos and other fretboard pyrotechnics. That it clocks in at under $900 off the rack makes the Pro Series DK2 a great value buy.
I'll be referring to a lot of different producers in this article, and it's understandable that you may not have initially heard of some of them, even if you've probably heard some of their productions. To avoid an avalanche of parentheses, I've put a list of all the producers I mention into a box which runs across the bottom of this article. The box also includes a few of their most celebrated credits, so that you can have some idea of where each of them is coming from stylistically.
Frets on finished fingerboards may be tough to measure accurately when the finish has appreciable thickness (think Rickenbackers, 70s Fenders) as these manufacturers spray the finish over the fretted neck.  I have measured a finish chip from a 70s Fender maple neck refret that was .010” thick – lowering the fret height by .010” (25% in the case of the stock medium wire at the time) from just finish alone.  I recently refretted a 2008 Fender Eric Johnson Strat where the fret height prior to any work was .040”, yet the crown of the fret removed from the fingerboard was .045”.  I personally do not like this feel and so often I will suggest refretting over a finished fingerboard when working with them rather than under the finish.

Before Nathan Daniel started the Danelectro company in 1947, he made amplifiers for Epiphone from 1934 to 1946. Epiphone wanted Daniel to make amps for them exclusively, but he preferred to stay independent. Instead he founded the Danelectro company in 1947 and started making amplifiers for Montgomery Ward. By 1948 Daniel expanded and became the exclusive guitar amplifier producer for Sears & Roebuck. At the same time he was also supplying other jobbers such as Targ & Dinner of Chicago.
Thank you Ola and David for this excellent article. The approach is totally scientific: you try to study the impact of one element of a system while keeping the rest of the settings identical (same pickups, same strings, same picking, etc.). The wood used modifies effectively the electrical spectrum composition and therefore the sound we hear. All the difficulty is that the wood is a part of a very complex system (woods combination, building type, pickups, strings, effects, amplification, restitution, etc.) and, without a solid knowledge or skills, it could be difficult to choose the right elements of the system to get what you want…
Some effects, and the boxes that produced them, altered musical periods beyond recognition. The valve-driven Watkins Copicat, for example, will forever be associated with the sound of the late 1950s British music “beat” scene. Developed by Charlie Watkins in 1958, this odd machine supported a tape-recording mechanism that would record and play back any sound with varying lengths of delay in-between the replay heads. The device was critical to the rockabilly sound of the late 1950s, the “beat-group” sound of The Shadows, and the Liverpool Merseybeat scene of early 1960s (as well as the Birminghambeat, or Brumbeat scene). The sensation of hearing a guitar warble and wail to its own output encouraged guitarists to experiment with different styles of attack and vigor. For example, the noise that begins and ends the original 1962 recording of “Telstar” by the Tornados was made using the Copicat by creating a loop of echo and reverb effects. This produced what can best be described as some sort of space-echo/attack-helicopter noise.
All electric guitars have this switch but it varies from guitar to guitar. it is called the pickup selector switch. It is used for deciding on which pickup to use on the guitar. On a les paul style guitar it can be used to select the neck (traditionally rythm pickup), bridge (traditionally used for lead) and both pickups together.\n. \n===\n. \nThat's what it is on a normal Gibson Les Paul. But on a Gibson Les Paul BFG, that is a "kill" switch that turns the guitar off completely. On many Gretsches, the toggle switch is a tone switch flipping between bassier and more trebly sounds. On most Fenders, that switch is down on the lower bout by the volume/tone controls (but on a Telecaster Deluxe, the switch is where it'd be on a Les Paul). Then there are oddities like the Italia Rimini, which has no pickup selector switch -- just individual volume controls for the two pickups.\n. \nEvery guitar has a different design. You'd have to look into every model.

The Chord Harmonica consists of two harmonicas hinged together. Together, they are capable of playing 48 chords. They are 23 inches long, and each chord takes up 4 holes. The chord harmonica is used to provide chordal and rhythmic backing in an ensemble, much as rhythm guitar might do. Jerry Murad's Harmonicat's 1947 "Peg O' My Heart" was played on a Chord, with a cleverly arranged sequence of chords that produced the impression of a melody. Hohner's main Chord is known as the Hohner 48, because it plays 48 chords. Hohner from the 1930s to the late 1960s also produced the Polyphonia No. 8, which played 36 blow-only chords, in three rows. The concept failed and is often frowned upon by professional 48 chord players.
{ "name": "Candy Apple Red", "skuUrl": "/Fender/California-Redondo-Player-Acoustic-Electric-Guitar-Candy-Apple-Red-1500000152032.gc", "status": "instock", "statusText": "In stock", "skuItemType": "New", "inventoryText": "In Stock & Ready To Ship", "inventoryKey": "in_stock", "availableDate": "09-22-2018", "price": 399.99, "isOnSale": false, "msrp": 400.01, "salePrice": 399.99, "easyPayOptions":"0,0,100002,6 Months Promotional Financing,01/01/2019,Special 6-month financing^ + $19 back in rewards Valid through,399.99,true,/pages/Gear-Card-Rewards.gc", "formatedIntegerValue": "399", "decimalValue": "99", "listPrice": 399.99, "isPriceDrop": false, "priceDropPrice": "", "savingsAmount": 0.02, "discountPercentage": 0, "promos":["coverageEligible","freeShipping","return"], "warranty": true, "sku": "site51500000152032", "shipToStore": true, "displaySku": "K47863000002000", "displayId": "1500000152032   POS #: 113861041", "serialized": false, "shipsFree":true, "condition": "New", "commerceType": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/K47863000002000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"false", "invMsgPreOrder":"false", "invMsgPromiseDate":"", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "", "styleImgAlt": "California Redondo Player Acoustic-Electric Guitar Candy Apple Red", "freeGiftWarning":false, "freeGiftWarningTips":"", "kitCarouselItems": [], "availableInStoreOnly": false, "isShipsInternational": false, "checksum":"352089750023", "restrictionType":"", "restrictionError":"" ,"storeInfo":[ { "storeName" : "La Mesa", "storeStatus": "Ship to Store" } , { "storeName" : "San Ysidro", "storeStatus": "Ship to Store" } , { "storeName" : "San Marcos", "storeStatus": "Ship to Store" } ] }
"The development of the modern tuning can be traced in stages. One of the tunings from the 16th century is C-F-A-D. This is equivalent to the top four strings of the modern guitar tuned a tone lower. However, the absolute pitch for these notes is not equivalent to modern "concert pitch". The tuning of the four-course guitar was moved up by a tone and toward the end of the 16th century, five-course instruments were in use with an added lower string tuned to A. This produced A-D-G-B-E, one of a wide number of variant tunings of the period. The low E string was added during the 18th century."[48]
The Whammy – If you’re familiar with the tremolo arm, or “Whammy bar,” then you already have an idea of what this pedal can do. Usually, the Whammy pedal is a rocker type, much like the wah, which shifts the pitch up and down as you rock it back and forth. Eddie Van Halen, Jimi Hendrix and Joe Satriani are a few of the artists you can listen to for a general feel of this pedal’s potential.
With a body shape that looks like it could have been cut out by hand using a saw in your garden shed, this Kay Old Kraftsman Sizzler guitar manages to be crude and quite fantastic at the same time. "Old Kraftsman" was actually a brandname used on Kay guitars sold by Spiegel stores. The maple neck gives it a rather Fender-like appearance, but this is in fact a set neck and not a bolt-on.
Where there is more than one pickup, a switch selects between the outputs of individual pickups or some combination; two-pickup guitars have three-way switches, and three-pickup guitars have five-way switches. Further circuitry sometimes combines pickups in different ways. For instance, phase switching places one pickup out of phase with the other(s), leading to a "honky", "nasal", or "funky" sound[citation needed]. Individual pickups can also have their timbre altered by switches, typically coil tap switches that effectively short-circuit some of a dual-coil pickup's windings[vague] to produce a tone similar to a single-coil pickup (usually done with push-pull volume knobs).
One of my favourite hardware effect units is the Electrix Mo-FX (sadly no longer in production). It is superbly constructed for hands-on performance and it offers full MIDI control over the panel's knobs and buttons. I use this in conjunction with the Sequentix P3 (a hardware step sequencer). Not only can the P3 generate patterns of controllers suitable for varying multiple Mo-FX parameters, but it can generate evolving or shifting patterns, courtesy of its 'accumulators'. In a nutshell, accumulators are designed to prevent your sequences becoming annoyingly repetitive: controller values (actually values directed at any internal sequencer parameter) can be added or subtracted on each pass of the pattern, with rules and limits directing the behaviour as the accumulation progresses. Digging through the Mo-FX manual quickly reveals all the MIDI Continuous Controllers you need. Usefully, you can also trigger the tap-tempo function via MIDI, and this offers a rather wonderful way of generating clock intervals. As you can decide exactly where to place your tap-tempo trigger events, and the P3 sequencer can shift or vary these events according to rules you devise, you can find clock sync intervals unseen on any other device. Paul Nagle

Here’s the idea: Conventional electric guitar tone controls employ a single pot and single capacitor connected to ground. As you turn the pot, more signal goes to ground for a darker sound. The capacitor value determines the cutoff frequency — the larger the cap, the lower the cutoff frequency and the darker the sound. In other words, the cutoff frequency is fixed, but the percentage of signal that gets cut off changes as you move the pot.
Buying an electric guitar is a very personal process, with many things to consider before you make your final choice. It’s not just a case of picking something with a nice color – you are usually parting with a substantial chunk of hard-earned cash, ranging anywhere from $100 to $2000 – or more – for some guitars, and therefore patience is required to find something that really suits you.
If you want to test the waters, here are the some of the best free guitar effects software packages. Aside from the limited freeware software, there are Lite or Trial versions of commercial programs which you can get for free, but with limited in features. The good thing though is that even when they lack features, they work and sound just as nice.
In Chicago in the sixties, "the rules had been laid down" for young, white blues bands, Mike Bloomfield told Rolling Stone in 1968. "You had to be as good as Otis Rush." That wasn't easy. A Mississippi native who moved to the Windy City in the late Forties, Rush was a fearsome electric guitarist – with a grittytreble tone and lacerating attack, like a gunslinging cross of Muddy Waters and B.B. King – as well as a knockout songwriter. Along with guitarists like Magic Sam and Buddy Guy, Rush helped create the more modernized, R&B-influenced approach to Chicago blues that came to be known as the West Side Sound. Rush's impact on later generations was enormous: His late-Fifties and early-Sixties singles were go-to covers for Led Zeppelin ("I Can't Quit You Baby"), John Mayall ("All Your Love [I Miss Loving]") and the J. Geils Band ("Homework"), while Stevie Ray Vaughan named his band after Rush's lethal '58 lament "Double Trouble."
I'm not sure if it's been made clear or not yet, but the imported firewood that had a Kay brand name on it in the seventies bears no relation to the products of the the Kay Co. of Chicago USA. It's not all plywood either; they had a range of total crap to not-so-crappy models. I never much liked their p.u.s or their necks. This is a good body (late 40's K-44) with a better (Harmony!) neck.

Simon Stockhausen began his stellar musical career at the age of five. His multi-faceted and wide-ranging oeuvre has since embraced all manner of projects and styles, including jazz and improvisational collaborations, countless compositions for ensembles and chamber groups as well as work for major European theatre companies and orchestras including the Hamburg and Berlin Philharmonic Orchestras. In 2009 he further extended the range of his musical endeavors with the creation of a sound design company through which he produces sounds, patches and libraries for software synths and plug-ins, serving sound designers, musicians and post production professionals.
Here, in this mini guide to acoustic guitar body types, we’ll aim to show you some of the key differences in size, shape, sound and suitability between the major variations of guitar. We’ll look at the history of some of the better known body types, and make recommendations according to the sound you’re going for and the style in which you play. So whether you’re a wispy finger-picker or a hearty strummer, we’ll explain some of the more intricate details of acoustic guitar body shapes.

Orange make great amplifier cabinets that work with a wide variety of heads. In fact, there are many artists out there who like to mix and match their amp+head combinations to get the specific sound out of their head combined with the classic sound of an Orange speaker cab. The Orange PPC212 Guitar Speaker Cabinet - 2x12 has been designed to bring the best out in your Orange amp head by utilising 13 ply, high density 18mm Baltic Birch plywood in a closed back construction partnered with 2 x celestion vintage 30 speakers. This Power Projection Cabinet (PPC) has been designed to last the test of time thanks to the rugged construction.

For players that want to start off purely in the world of metal playing, this Schecter bundle should be right up their alley. The guitar itself has a lovely midnight satin black finish, with ready access to its 24 frets thanks to a generous cutaway. The dual humbucker pickups will put out plenty of power as well, allowing for more extreme styles of music to be played with ease. This particular set skips the accessories in favor of a mere amp, gig bag, and instrument cable, but the quality of the main instrument makes up for the omission of picks and the like.

With the correct strings on the guitar, and the strings tensioned to the tuning you intend to use, place a capo at the first fret, or depress the low "E" string at the first fret. While doing this, depress the same string at the 12th fret. Site along the bottom of the string and note its relationship to the top of the frets up and down the fretboard between the fretted positions. The string in this situation, since it is under tension, is essentially a straight edge, and the curve, or profile, of the fretboard can now be seen. Generally, a gap of 1/64 - 1/32 " between the bottom of any string and the tops of the 6-7th frets (when fretting the string at the 1st and 12th frets or higher) is considered acceptable. You could go a hair flatter, or even a bit more curved depending on the needs of a given player, but start here.

Everyone from Jazz guitarists to lovers of Queens of the Stone Age style heavy rock have fallen in love with the Artcore series since it was first introduced in 2002. Fusing expert workmanship with affordability, the Ibanez 2017 Artcore AS53 Semi-Acoustic Guitar, Transparent Black Flat is one of the best cheap electric guitars you’ll find on the market today. It’s budget friendly price tag makes it a fantastic choice for beginners whilst the high-quality pickups and superb tonewoods are the reason why so many pro level players will choose it for the stage and studio.
If you’re paying attention, you probably noticed that I forgot to mention EQ and volume pedals. Actually I didn’t. Placement of these particular pedals depends more on what you want to achieve with them than any hard and fast rules. For example, you may want to place a volume pedal at the very front of the signal chain to perform dramatic fade in and fade out effects or to better regulate the guitar’s level before it hits any effects (or you could just do what I do and use the guitar’s own volume control). Placing the volume pedal near the end of the signal chain just before the delay and reverb effects allows you to perform professional-sounding fades or mute the guitar’s signal without cutting delay or reverb tails short. If you use a loop switcher, a volume pedal can be paired with a single effect, and you can use the volume pedal to blend or mix that effect independently.
Thanks. It sounds good without tone shaping ability but I wanted to hear the original sounds. It now has 2 capacitors tied together from the volume pot to 1 tone leg. I am guessing the original tone switch was wired with one cap. for the low & one cap. for middle and the 3rd tone leg was straight wired for treble high. I also wonder how the ground sweep worked on the tone selector?? I just need to know. I’m a DIY guy.
Most delay pedals have controls for the number of repeats (called “feedback”), the volume of the repeats and the time between each repeat. Some pedals have what’s called “tap tempo”, where you can tap your foot on the pedal and the delay unit will match the speed of the effect to your foot, allowing you to match the delay time to the tempo of a song. Delay pedals are often used to thicken up heavy lead guitar sounds, or to subtly add more to a simple rhythm guitar part.
As with many of our services, we do more than just pull and replace your frets when doing a refret. Full refrets include a resurfacing of the fingerboard to proper level (even more precisely done than many factories), repair to any damaged fret slots, nut removal and reuse (when applicable), and full Calibration and Reset service (which includes a full traditional set up). Strat style tremolos add $10 to the price, Floyd Rose style bridges add $30.
I've been an on/off guitar player for at least 15 years now. Never really good, but steadily improving. My hardest thing is consistent motivation. I go through spurts where I study theory and practice like crazy and then, suddenly I just stop. I got this both because I was exceited about it's teaching potential (lessions were $20/30 min when I was a kid, got this for $25) and it has got me playing again and is a lot of fun.
Dude I totally agree with you,Eddie Hazel was awsome.And Add Ernie Isley (he learned from Jimi Hendrix when he played with the Isley Brothers),And Carlos Santana(his oloder stuff,check out the Borboletta album from 1975),and if you like Hendrix and stevie Ray why isn't Robin Trower (Robin Trower Live) on this list ?Also the guitarist from the band Slave(he was17 when they cut the album with "Slide"on it).Most of these are Metal guitarists,I prefer a guitarist that can make the hair on the back of my neck stand up when they play.Someone that makes you feel different emotions when they play.Just because you can play super fast doesn't make you great.
Morning everyone, well it is here in UK anyway. Who can help with my find. It's a Dia Hummingbird labelled F 315 but no serial number. So from what I can find Dia was a brand used by Matsumoku but I can only see electrics under Dia brand when I search. However it looks identical to a Aria F315 Hummingbird on eBay USA at present, and identical to an Aria Pro II from the 1976 catalogue but labelled W 30 model I believe. I won't put a link on here in case I'm breaking rules. It has that weird aluminium compensated bridge and seriously, this one looks brand new with two tiny dings that would make it a second or an ex-demo if it was on sale. Action at low E 12th is about 2.7mm and about 1.8 at high e. It's in such good condition I began to question if in fact it is a 'knock off of a knock off' though why anyone would think that would work I can't guess. It is very very playable, and at first I wasn't keen on the tone though sustain is great (despite bridge) but I changed to heavier strings (13) with much improvement. I'm seeing a luthier friend next week who is finishing off work on a brilliant Terada FW 613 (D18 clone if you like), but I'm wondering whether to get him to replace the whole alloy bridge. I can do a couple of pics if anyone is interested. Any help in identification of maybe year (guessing 1976) and origin greatly appreciated. I think it's a keeper, but should I change that bridge ? Has anyone done similar on one of these compensated aluminium designs and what were results. Many thanks.
While electric bass players have used regular guitar amplifiers in large concerts since the 1960s, this is usually just for the higher register; a bass amp is still typically used for the low register, because regular guitar amps are only designed to go down to about 80 Hz. One of the reasons bassists split their signal into a bass amp and an electric guitar amp is because this arrangement enables them to overdrive the higher-register sound from the electric guitar amp, while retaining the deep bass tone from the bass amp. Naturally-produced overdrive on bass obtained by cranking a tube amplifier or solid-state preamplifier typically results in a loss of bass tone, because when pushed into overdrive, a note goes to the upper octave second harmonic.
Serial #59640 New York label Epiphone Triumph circa 1949. Blonde finish. Spruce top, tiger flame maple sides and back. Cherry neck with diamond mother of pearl inlay. Small nick less than an inch wide on left front. Original Frequensator tailpiece with nickel finish, partly worn. Grover tuners fastened with screws and glue. Edging on back body has .25” gap at connection.Blonde natural lacquer finish in good condition. Glossy and brilliant color. Shipping quote inside US only. Ask for quote outside the US. 
Yet another acoustic steel guitar for the right handed guitarists. It has 6 strings and mostly comes in tobacco sunburst without a case. The perfect design makes it suitable for use by beginner guitarists. The sides and the back are made of meranti, with a spruce top. It is quite cost effective, with prices ranging from around INR 8,500 depending on available offers. More about Yamaha F310 TBS can be found on the following website link.
When we take a look at a guitar neck, it is important that the guitar is under string tension and in playing condition when measured. The PLEK measures the instruments neck and fret height with the instrument strung up to pitch. The computer ascertained a 3-D like graph of the fret board surface, including the position and height of the strings. Thanks to the PLEK SCAN the relief of the neck made by the string tension is taken into account while calculating the process-parameters. The operator then has the ability to manipulate the parameters to give the player an optimal playing instrument.
The initial single-pickup production model appeared in 1950, and was called the Esquire. Fewer than fifty guitars were originally produced under that name, and most were replaced under warranty because of early manufacturing problems. In particular, the Esquire necks had notruss rod and many were replaced due to bent necks. Later in 1950, this single-pickup model was discontinued, and a two-pickup model was renamed the Broadcaster. From this point onwards all Fender necks incorporated truss rods. The Gretsch company, itself a manufacturer of hollowbody electric guitars (and now owned by Fender), claimed that “Broadcaster” violated the trademark for its Broadkaster line of drums, and as a newcomer to the industry, Fender decided to bend and changed the name to Telecaster, after the newly popular medium of television. (The guitars manufactured in the interim bore no name, and are now popularly called ‘Nocasters.’) The Esquire was reintroduced as a one-pickup Telecaster, at a lower price.

Your budget – When it comes to the best electric guitars or really any real instrument in general, you’re going to have to pay a decent amount of money if you want a quality investment. Although we did find a few budget-friendly guitars to take a look at below, a lot of these will near the half-a-thousand mark and beyond. It all depends on you, of course. Do you want a beginner and starter electric guitar to begin those shredding adventures? Or perhaps the best of the best that the most famous artists use? Perhaps you’ll end up saving more than you already have as you’re reading this — it may be worth it to wait a bit longer.
The Line 6 Spider Classic 15 is similar in many ways to the Fender Champion 20. It offers digital simulations of various amplifiers and built-in special effects. The two amps are usually priced identically. The reasons we didn’t make the Spider Classic 15 our top pick is that it’s much larger and heavier than the Fender (about 40 percent overall, at 14.7 by 15.7 by 8.3 inches and 18.4 pounds), and its controls work in an unusual fashion that sometimes frustrated our panelists.
The pre-amplifier section of a guitar amplifier serves to amplify a weak instrument signal to a level that can drive the power amplifier. It often also contains circuitry to shape the tone of the instrument, including equalization and gain controls. Often multiple cascading gain/clipping stages are employed to generate distortion. Because the first component in a valve amplifier is a valve gain stage, the output level of the preceding elements of the signal chain has a strong influence on the distortion created by that stage. The output level of the guitar's pickups, the setting of the guitar's volume knob, how hard the strings are plucked, and the use of volume-boosting effects pedals can drive this stage harder and create more distortion.
“I was getting really bored with this guitar sound—or lack of an interesting sound,” Davies remembers. “There was this little radio spares shop up the road, and they had a little green amplifier in there next to the radios. An Elpico. I twiddled around with it and didn’t know what to do. I tried taking the wires going to the speaker and putting a jack plug on there and plugging it straight into my AC30. It kind of made a weird noise, but it wasn’t what I was looking for.
For a very good price, you get a solid spruce top, mahogany back and sides, and a rosewood fingerboard with matching bridge - for elegant finger picking. The bracing on the inside of the body is scalloped for even better tone, which works very nicely indeed. There’s also a System 66 preamp system with 3-band EQ and a builtin tuner for precision. It’s all good quality, mid-range equipment making this a really great value proposition.
1958-1969: replaces the "U" models and now has a double cutaway body with short horns. Masonite/poplar frame bodies, 13.25" wide. Models numbers include the "Standard": 3011 (black 1 pickup), 3012 (bronze 1 pickup), 3021 (black 2 pickup), 3022 (bronze 2 pickup), 5025 (blond 2 pickup). The 3021 is considered THE Jimmy Page model. "Seal" shaped pickguard and concentric knobs on 2 or 3 pickup models. Round control knobs.
How a guitar feels is highly subjective – after all, even guitarists come in all shapes and sizes. While the acoustics in our list are all made in such a way that most guitarists will find them comfortable and easy to play, there’s still no beating being able to try several models out so you can choose which one feels like it’s a part of your body.
By 1961, at least, the makeover was complete. The old mini Les Paul, the J-1, was changed to become a sunburst double-cutaway solidbody. These had widely flaring equal cutaways, a single rectangular neck pickup, a large pickguard which covered most of the treble side, a wooden adjustable bridge, covered tailpiece, volume and tone. The bolt-on neck now had a more Gibson-style open-book head shape (with round logo sticker). The fingerboard had the old large dots with two small octave markers. The J-1, in a number of forms, would survive at least through 1966, if not longer. It is presumed that the J-2 was still around and that it had also become a double-cutaway; it most certainly was still in the catalog, as a double-cut, in ’62.
Another way of categorizing bass equipment manufacturers is by which part of the market they are targeting. While Peavey and Yorkville products are aimed at the generalist mass market, some bass equipment manufacturers, such as Acoustic Image or Walter Woods make expensive "boutique" equipment that is aimed at a niche market within the professional musician market. Acoustic Image amplifiers and speaker cabinets tend to be used by professional acoustic folk and jazz musicians, and Walter Woods amplifiers are associated with professional acoustic jazz bass players.
Capacitors are typically used as filters to control tone. In most cases, they are used to filter out very high frequencies before being sent to ground (the output jack) which controls the warmth of your guitar’s tone. Capacitors vary greatly and come in a range of materials from ceramic, film, paper and electrolytic (mainly used with active pickups).
After shaping your sound, is important to add some depth to it, and here’s where the ‘ambiance’ pedals find their way into your rig. The chorus effect should be used properly, without overdoing it, but can give great results: the depth and the ‘3 guitarists playing your part’ effect can work amazingly well for your music. Delay and Reverb can be used lightly, in order to enhance your sound and fill up your guitar solos with a little space (by setting up a nice spring or hall reverb settings and a dotted delay) or heavily, to achieve creative sounds where the sky is the only limit.
Silvertone starter pack is incredibly hard to beat. The candy blue finish gives the guitar a gorgeous aesthetic that looks fully professional. The pickup selector has 5 positions, and there are two tone knobs to give even more control over the sound. Stratocaster fans will love this guitar! Also included in the set is a gig bag, small Silvertone amp, strap, 5 picks, Allan wrenches, strings, a clip-on tuner, and a tremolo bar.

I always respond to these enquiries as I have played some in UK shops and like them a lot .Well designed and made though I am sure the odd duffer gets through like most imports .Trev Wilkinson did the designing ,though it should really read ,modifying ,as most are other makers basic designs,.The Les Paul lemon drop is superb judging by reviews and I loved their S types ..Worth the money it seems .I would prefer a Vintage Strat , 335 or Les Paul to the other cloned alternatives .I did buy an Epiphone Dot but after playing a Vintage 335 ,wish I had bought it instead .The ones I played were Chinese

Rickenbacker continued to specialize in steel guitars well into the 1950s, but with the rock and roll boom they shifted towards producing standard guitars, both acoustic and electric. In 1956, Rickenbacker introduced two instruments with the “neck through body” construction that was to become a standard feature of many of the company’s products, including the Combo 400 guitar, the model 4000 bass, and, later, the 600 series.

Shop our selection of guitar and bass electronics parts and supplies. Everything you need to to finish your guitar electronics project like a pro. Volume and tone pots, pickup selectors and mini switches, jacks, tone capacitors, wire, solder, shielding and more. Get the full potential from your guitar's pickups with the finest quality guitar electronic parts from top manufacturers like: CTS, Bourns, Fender, Switchcraft, CRL, and more. 
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Maple - Quilted - Frets: 24, Jumbo - # of Strings: 6 - Headstock: 3+3 - Bridge: Floyd Rose Special Tremolo - Cutaway: Single - Hardware: Satin Chrome, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickup Configuration: H-H - String Instrument Finish: Transparent Amber Sunburst, Transparent Black, Transparent Red
As I commented above, my go to method for quiet practice is a PocketPod with Shure headphones. But, who doesn't like plugging in to an amp every once in a while? I live in a house, but the neighbors are close. The amp I use is a Fender Super Champ XD, which is a 15w tube amp with some digital effects. It seemed quiet enough at low volumes, but your mileage may vary. If I were you, I would at least give one a listen at a music store and see if it can do what you need.

Because of the way the guitar is tuned and the amount of spread between the notes of each individual strings chords are voiced in certain very particular ways. These voicings are physically impossible to imitate on a keyboard, at least with any reasonable amount of facility. Conversely, keyboard voicings are generally unplayable on a guitar, as you'd have to be playing more than one note on a single string in many cases.

The fully hollow body electric guitar is almost always a finely crafted work of art.  These instruments are a throw back to the days of hand shaped acoustic instruments of yesteryear.  The hand carved archtops and backs are designed to take advantage of pure acoustic detail, such as resonance and tone, while the electric aspect allows the performer to be amplified.  A pure traditionalist could ask for nothing better tone wise, but must contend with other aspects of these incredibly resonant instruments.

I gave some relief to the guitar, just enough to be able to move a business card on the 8th fret. I think the truss rod adjustment is ok now. Strangely it's still buzzing. I compared the height of the bridge to my Navigator N-LP-380LTD and i have the same height on the RLG-120 the same. The string that buzzes the most is the D string!!! E and A string buzz too but less than the D. Don't know if i want to raise the bridge more. G B E are ok! Don't know if the D slot on the nut is too low. Seems like the slots on the nut on my guitar are higher than the ones on your Burny. Don't know what to do. Frets seem even. Any chance it's the saddles or something? Do they play a role on buzzing. I will raise the bridge tomorrow morning and see how it goes. Any idea what should be a standard string height on these guitars? Lets say height on 1st fret, 5th fret, 8th fret, 12th fret, 16th fret, 22nd fret. Can we say that? Can you tell me yours to check with mine?
If any item fails to meet your expectations at any time, please return it for a refund or exchange. From tuners to endpins, everything we sell at Stewart-MacDonald is backed by our rock-solid guarantee of satisfaction. This is how we do business, ever since selling our first 5-Star Banjo Head in 1968. We proudly continue this tradition by offering quality products and standing behind them.
A common issue for playing on larger stages or in studios is the distance between a guitarist’s pedals and their amp. Guitar cables that are longer than eight or nine meters (25 or 30 feet) not only degrade the quality of the signal, but also become incredibly susceptible to noises like hiss and hum. To allow guitarists to drive their signal over 100 meters (300 feet), Radial created the SGI-TX/RX™. The SGI changes the unbalanced guitar signal to a balanced line-level signal, altering the impedance for longer XLR cable runs; guitarists are able to use their amps offstage or in an entirely separate room when trying to craft the perfect tone.
Equally potent, the B.C. Rich Mockingbird is another model that is prone to stir up your interest. This device features a bolt-on body, besides, at a quick look; this guitar might remind you of the classic “NJ” style headstock. Furthermore, the guitar’s body is made from mahogany, and it comes fitted with a rock Maple Neck and a very well regarded Rosewood fretboard that is said to supply its users with a great tone, extra playability, and outstanding stability.
There’s 200 unique patch locations for you to assign your own sounds with and make use of the effects for guitar and bass, including world class BOSS delays, reverbs, mod/pitch effects, overdrives, distortions such as the DS-1 and Metal Zone and more. A built-in tuner is extremely handy as is the onboard USB interface which allows you to load presets onto the unit. This multi-effects unit allows you to access the free MS-3 Editor/Librarian software on a Mac or PC where you can make changes to your effects, assign parameters and sculpt your sound in complete detail for later recall when you’re playing live. You can mix whatever pedals and sounds you want and have that preset ready to go in seconds.

So, what string gauge is standard for electric guitars? Most new guitars come strung with super-light or light-gauge strings. For beginning guitarists, that’s probably a good place to start. As you develop fretting and picking skills and your fingers gain calluses and strength, you may want to gradually move up to heavier strings, depending on the music you play and the tone you seek. Many guitar manufacturers make specific recommendations about what strings to use. Some produce their own strings or have them custom-manufactured to their specifications.

If you are not attracted to the way the guitar looks or feels in your hand, chances are you won't be too eager to pick it up every day. When you are just starting out, this is supremely important. Here's where a disclaimer needs to be placed. This isn't always the case, and often times people warm up to a guitar even if they didn't initially like it, but why chance it?

As you know, like most guitars sporting more than a single pickup, your Strat lets you select any pickup by itself or choose certain dual-pickup combinations. The standard way to connect multiple pickups is to wire them in parallel. This generates the classic tone our ears know from countless records, when a guitarist uses the bridge and middle or middle and neck pickups in tandem (positions 2 and 4 on a normal 5-way Strat switch).
A while back I bought a GuitarPort, a product from Line6 that was one of the earliest guitar-to-PC interfaces. It cost me $99. It connects through USB and I could plug the guitar into it. I could play amp models and effects through my PC and the sound would come out of the computer speakers. (Headphones are of course an option through the PC speakers)
Hi, it seems like the problem lies in your hands and not in the guitar itself. If you are a beginner, you must start slowly and build up strength in your hands. A good way is to simply buy a "stress ball" or other hand exerciser. A "Gripmaster" one that lets you work each finger individually, which can be very useful, they are available for about $20 at most music stores.
Some Craigslist and EBay sellers have been claiming the 500 and 600-series Kents are made by Teisco. I think we’ve shown that that’s not the case. Some sellers also describe those early Kents as having “Ry Cooder” pickups. As most of you know, Ry Cooder is an incredibly talented multi-stringed-instrument musician. David Lindley, another great talent, gave him a pickup from an old Teisco guitar. The photo at left is exactly like it. Cooder put the pickup into one of his Stratocasters and liked the sound so much that he got another one and put it into another Strat. These pickups are also described as “gold foil” pickups. There are variations in the pattern of cut-outs on the chrome covers of different pickups. I don’t know if the others sound any different, but if I were looking for a “Ry Cooder Pickup”, something like the one pictured here is what I would be looking for. The pickups have become worth more than the guitars they are on, consequently, as the guitars are bought up and trashed for their pickups, their prices are going to rise.
Is there a correct guitar pedal order? Every guitarist will move into using effects pedals in their signal chain, which is when the chaos starts. What the heck is an effects loop? Why is there more than one output on a pedal? This is the same plight mix engineers and keyboardists deal with. But thankfully, with a decent explanation, you'll find there is a logical sequence your effects should be in. Today we explain what that order is and why...
One step up is the combination of a treble cut and a bass cut, with a single knob to select between them, like the one in the Electro-Harmonix Big Muff (Figure 2). The knob selects a blend of highs left over from the bass cut side and lows left over from the treble cut side. If you make the cut frequencies of the treble and bass sides far apart, you get a persistent midrange scoop, as in the original Big Muff. You can also have the bass and treble sides overlap in the middle and get a midrange hump in response. The near-endless variations you can get by tinkering with the relative values of the parts and the need for only one knob make this a favorite in effects.
Why Martin electric guitars have never been more popular isn’t too hard to figure out. Martin, whose expertise has always been in top-notch acoustics, never really put a lot of effort into marketing its electrics. They were always well made, and, especially in the necks, clearly “Martins.” In the final analysis, however, it probably comes down to being victims of the success of their acoustic brothers, and players have just never seemed to warm up to the idea of Martin “electric” guitars. For the savvy collector with a taste for quality and relative rarity, Martin electrics remain excellent and attainable prizes.
I have a shecter omen extreme 7 and found that the factor strings they put on were nice for my small fingers. I had to replace because the factor set in general needed some tweaking and they changed all the strings. Now i don't really like the strings they put on. Too small. All they had listed for the strings were 24X jumbo strings. What string set should i buy since i play Ambient, soft, but also djent metal.

Taylor, Martin, Gibson all great production brands... Which is better comes done to what you like sonically, visually and of course the feel in your hands. It is also difficult to compare one brand versus another unless you are comparing similar designs using the same tone woods and in the same price range. Anyone espousing one is better than the other without doing this is not being honest with themselves. I own a Martin and two Taylors, all are great and have different voices and feels... Even the 2 Taylors are very different in sound and looks. In the end I vote for Taylor because I like the neck carve and feel that the looks and build quality are a bit better in the $3K - $4 price range. If your looking for something in a lower $500 - $1, 000range you probably should be considering Yamaha or Takamine. Though in the end you get what you pay for.

After all, we each have our own favorites, whether it be a particular player, style or era. However, that doesn’t mean such a list can’t be based on some element of objective reasoning. To some extent, the proof is in all of us: anyone who picks up the instrument borrows at least a handful of techniques and stylistic tendencies that someone else brought to the table. The key is determining which guitarists have had the most impact among the larger number of players—in other words, who has contributed most across the board to the way we approach the instrument.

The roots of the Supro story go back to the ’20s and the sometimes tempestuous relationship between Czech immigrant/instrument repairman/inventor John Dopyera and dapper Vaudeville musician George Beauchamp (pronounced “Beech-um”). Both were searching for the guitar’s holy grail of the era, more volume. Disagreement, and some animosity, has always surrounded the account of just who was responsible for what, but Dopyera ended up building an ampliphonic or self-amplifying guitar (or “resonator” to most guitar buffs) for Beauchamp. John applied for a patent on his tricone design on April 9, 1927, obtaining it on December 31, 1929.
There are several aspects that make the acoustic guitar different from the electric one. The most notable difference is the fact that the acoustic types do not need a source of electricity or rather they do not have to be plugged in for them to be heard. They are relatively large and are built with a hollow chamber for the magnification of the guitar’s resonance thus giving out sound that originates from the plucked strings. It also has a bridge that is essential for the transmission of vibration of the strings to the body. They are self contained, needing minimal preparation to play. In other words, they are the guitars to be bought by all those looking for simplicity.
The electric guitar was born out of necessity. Going back to the big band era, acoustic guitar players needed an instrument that could be heard over all the brass and woodwind instruments. They also need to be heard over the banjos and mandolins on the front porch. In the 1930s, companies such as Rickenbacker and Gibson started to add guitar pickups to their instruments, which allowed musicians to plug them into an amplifier for added volume. Rickenbacker added a pickup to their Hawaiian guitar (also known as a lap steel guitar) “Frying Pan” model, and similarly, Gibson added a pickup to their electric Hawaiian EH-150 model. Soon after that, Gibson introduced the iconic ES-150, which gave players the very best of both worlds. It gave guitarists a world-class Gibson hollow body guitar with a built-in pickup, which made it the perfect fit for guitarists who played large ensembles. In 1951, Fender revolutionized the electric guitar market even further by unveiling the first ever mass-produced solid body electric guitar, now known as the Telecaster, which was introduced in order to combat the feedback that hollow body electric guitars produced. Then in 1952, Gibson worked closely with one of the most widely respected guitarists of the era to create the first Gibson solid body electric guitar, now known as the Les Paul and named after its co-inventor.