While it’s not the most refined thing out there, Jackson Pro Series SL2 is definitely a force to be reckoned with. Minimalist design combined with bulletproof components is the type of recipe you want if you’re looking for a solid guitar. Playable, with great tone, this Jackson definitely spiked my interest in the brand again. Best of all, it’s reasonably priced considering what it offers.
While electric bass players have used regular guitar amplifiers in large concerts since the 1960s, this is usually just for the higher register; a bass amp is still typically used for the low register, because regular guitar amps are only designed to go down to about 80 Hz. One of the reasons bassists split their signal into a bass amp and an electric guitar amp is because this arrangement enables them to overdrive the higher-register sound from the electric guitar amp, while retaining the deep bass tone from the bass amp. Naturally-produced overdrive on bass obtained by cranking a tube amplifier or solid-state preamplifier typically results in a loss of bass tone, because when pushed into overdrive, a note goes to the upper octave second harmonic.
I played electric guitar in a band from the age of 12 through to the age of 36, then gave it up. Now, at the age of 68 I want to get back into playing. I went into a store and tried playing and found that my fingertips really hurt! Are there any electric guitars where the metal strings don’t hurt or do I just need to “grin and bare it” until my fingertips get calloused again?
We tried adding treble to the acoustic guitar.. It sounds like a xylophone, only the highs are heard. Panning is a good idea. I remember doing it with several synthesizer tracks to make more space. Unfortunately we already have a compressor in the pedal-board and it doesn't help much. The dynamics are flat but the electric guitar is still screening the acoustic one even at a quite low volume. I guess it will still be so... whatever we do. I wonder how people manage 4 or more guitars all at once. – SovereignSun Jan 10 '17 at 9:28
If you're looking for one of the best Strats Fender has to offer, be sure to check out the Fender American Professional Stratocaster. Developed with pickup master Tim Shaw, its brand-new V-Mod single-coil pickups are voiced specifically for each position, mixing alnico magnet types to produce powerful, nuanced tones with original Fender sonic DNA. For metal guitarists, have a look at the Jackson JS32 DKA electric guitar. Swift, mean, and easy to play, this guitar offers classic Jackson tone and playability at a more than affordable price. If you're looking for a Les Paul guitar, a great choice is the Epiphone Les Paul Custom PRO electric guitar. If you're ready to step up to a Gibson Les Paul, the 2019 Gibson electric guitar lineup is in-stock.
Promotion lasts for 1 year from date of purchase. After that period, your voucher is redeemable for the amount you paid, less any value you may have received. Not valid as payment for Eat24 purchases. Not valid with other vouchers, certificates, or offers. Only 1 voucher(s) can be purchased and redeemed per person. Cannot be purchased as a gift. Subject to the General Terms. Learn more View more

Companion to the TG-64 was the TB-64 bass. This was virtually identical to the guitar – including the three pickups and monkey grip – except it was a bass, so it had no vibrato. Two other basses debuted in ’64, the NB-1 and NB-4. These were basically the same guitar as the TB-64 except they did not have the handle cutout in the body. The NB-1 had a single pickup and the NB-4 had two.


My first recommendation is Epiphone. It is not just one of the best but it is the best guitar brand for beginners who are looking to buy a guitar to learn the ropes. I have included a few recommendations from this brand in this post. If you don’t know which one to buy and you are a beginner then buy one from this brand and you won’t go wrong for sure.

These multi-effects pedals are exactly what the name suggests: all-in-one models that pack multiple effects into a single box. There are a few benefits to this, one of which is value, since getting more than one effect at once gives you great bang for your buck. They also tend to come with presets that give you customized mixes of their various effects, which can do a lot to teach you how different effects interact and how to mix and match them yourself.


For my tastes, position 1 on a clean tone can be a bit too boomy. Even if one backs the volume a bit to take the edge off, it doesn't quite suit acoustic-style strumming. Position 2 is perfect for these sorts of things, though. I'd always use it for the small high chords you often find in funk and reggae. Position 2 is also a nice way thinning a distorted tone without it cleaning up too much, like Position 1 with the volume dialled down does. If you have your rig set so Position 1 screams, Position 2 will sing.

Nowadays, you can find many in-between sets, but you'll want to have a solid understanding of what the gauges are in terms of actual measurement and how they affect your ability to perform with your desired tone.  These relatively open descriptions will also differ from acoustic strings to electric strings, so your experience in handling many types of guitar strings and gauges is paramount in making the right choice.
SolidBody (2008) – Taylor’s take on a traditional solid electric guitar. Made from a solid slab of wood with cavities only for the pickguard or direct mounted pickups, and the bridge. Designed from the ground up, each SolidBody model features solderless pickups or a solderless pickguard which permit for musicians to effortlessly change the sound of their guitar. The SolidBody line is fully customizable with a wide combination of wood, colors and electronic configurations, and single or double cutaway options which enables anyone purchasing a SolidBody to get the sound and look that they want. All options are available for customization through Taylor’s SolidBody Configurator on the Taylor website.
The Yamaha APXT2 is a 3/4 size version of the world's best-selling acoustic-electric guitar, the APX500III. This well-constructed, compact guitar makes a great companion when you're on the road. The APXT2 features an ART-based pickup system and Yamaha's proprietary tuner, offering great sensitivity and accuracy for quick tuning. The APX T2 also includes a gig bag.
This deal leapt out of the page at me straight away. The Fender Squier series has been around a while and even though it’s a budget guitar, you can always rely on Fender for great quality. But what I like the most about this package is that everything you need is included (apart from a guitar stand) and the Frontman 10G amplifier has some extra features that are excellent. The amp has an input for a playback device to jam along to (like your iPad or Smart phone, or even a CD player) plus a headphone output for when the neighbours get too annoyed. A Gain control and Overdrive switch let you grunge everything up, or you can dial it back to a classic, clean Fender sound.
Harmonizers – Commonly used for vocal harmonies, these pedals can do a lot to beef up your sound. You can also use them in creative ways, like Steve Vai and Robert Fripp, who have been known to disable the main signal altogether so that their music is coming only from the pitch-shifted output. Using a modern harmonizer can be as easy as setting it to the key you’re playing in, and many even support more than one harmony at once.
In May ’71, Ovation tried once more. It introduced the K-1217 Typhoon V bass, about which no information is available, but based on the Eclipse, the difference may have been pickups. The K-1235 Eclipse was also introduced. This was a guitar offered only in a black finish that looks somewhat like graphite. It had chrome hardware, no binding, dot inlays, three-way select and two volume and two tone controls. The pickups had metal covers with black inserts and a single blade-style pole. In June ’72, all Electric Storms were discontinued except the Tornado and Eclipse, which made it another half year, until January ’73, by which time the Electric Storm had subsided into quiescence.
With electric specifically, it's important to ask what genre's of music do you want to play and who are your influences. A humbucker pick-up found in Les Pauls and SGs sound MUCH different than single-coils found in Stratocasters and Telecasters. If you like the sound of your guitar heroes, chances are you will like playing through similar gear. Again, go with my BUDGET, FEEL and SOUND trifecta!
The Hi Flyer guitar and bass would be offered pretty much until the end, in ’77. At some point after, probably around ’73 or ’74, the plastic logo was changed to an outline decal logo. Also, at some point the pickups were changed to the distinctive twin-coil humbuckers with metal sides and a see-through pink insert on top. These changes most certainly occurred by the ’76 catalog, when the Hi Flyers were available in four finishes – sunburst (U1815, U1815B), white (U1816, U1816B), black (U1817, U1817B) and a cool natural with maple fingerboard and black dots (U1818, U1818B).
I have an acoustic that I bought from a lady I know who said she has had it since the early 70's. It says 'Maya' on the headstock and the reinforcement rod cover is stamped with 'Takamine'. The sticker inside the sound hole says 'Maya', "We made this guitar for the people who love guitar music", Made by Takamine, Model No. TF1o1S, Japan. On the inside of the sound hole at the top, the wood block there is stamped with 46.6.3. The guitar is only about 3 1/4 inches deep and approx. 15 inches wide at its widest spot. Small guitar with a big beautiful sound.
If a player uses a separate preamplifier and power amplifier, she or he can buy a power amplifier intended for a sound reinforcement system or PA system or pick a power amplifier designed specifically for bass instruments. These preamps and power amps come in two formats: 19 inch rack-mountable units and units with their own wood or metal case. If a player uses a rackmountable preamp and power amp, these units and any effect units, such as an audio compressors, can be mounted in 19" rack mount road cases for safe transport. When a bass player selects a variety of different preamps, effects units and a power amp and puts them all in a rackmount case, this setup is colloquially called a "bass rig". Amp heads with their own wood or metal case may use many of the same appearance and transportation-oriented design features used on combo amps. For example, if a bass amp head is designed with a wooden case, it will typically have a vinyl, felt or sturdy fabric (or painted coating) to protect the wood case during transport; a carry handle; and corner protectors.
This is the main component that separates acoustic guitars from electric guitars. A pickup senses the vibration from a string, transfers it to the guitar amplifier which then transfers it to the loudspeaker. There are many pickups but we’ll cover the four basic ones. The single coil pickup has a single coil of wire with two horseshoe-shaped magnets. They produce a bright, cutting sound and are quite noisy. The P90 pickup is a single coil pickup with one wide coil that increases the surface area of the strings, producing a bigger yet less bright sound. Humbucker pickups were designed with twin coils. They produce richer, warmer, more powerful sounds but roll back some higher frequency sound. Active-passive pickups use a battery-powered circuit to produce a powerful yet balanced tone across a range of frequencies. It outputs a balanced, clean tone.

I’m going to be doing a pickup upgrade in the next few months on a Strat-style HSS. I have an idea, maybe a crazy idea, about how I’d like to wire it but so far I have been unable to find any indication that it is even possible. This site seems like the best place to get an answer. The single coils in my guitar will be replaced with another set of single coils (Seymour Duncan SLS-1 lipsticks). The humbucker I plan on installing (DiMarzio Tone Zone) is capable of being coil-split, which I want to take advantage of BUT I would rather not install a push/pull pot. My wiring idea… Toggle Position: 1) Full Humbucker, 2) North coil only of humbucker for single coil performance, 3) middle coil only, 4) middle and neck, and 5) neck only. Is this even possible using the 5-position toggle switch I already have, or is there no way to do it besides using a push/pull pot or installing an additional mini-toggle?

Since 1982, Dusty Strings Music Store has been a gathering place for instrument players and music lovers. Come explore new, used, rare, and vintage acoustic guitars, electric guitars and pedals, mandolins, ukuleles, banjos, harps, hammered dulcimers, and accessories -- all within reach and ready for you to play! We are an authorized warranty repair shop for both Martin Guitars and Taylor Guitars and carry such builders as Martin, Taylor, Collings, Goodall, Deering, OME, Weber, National, Fano, Nash, Silvertone, G&L, Tone King, Vox, and more. Our school offers private lessons, group lessons, concerts, and special events. Come play music!


Placing a texture-based effect such as chorus before distortion basically means that the chorus effect will be distorted rather than the distorted tone getting some chorus. That may sound kind or original and appealing to some but trust me – you do not want to waste your distortion pedal effect by distorting an already subtle effect. This very concept is extremely important in determining the correct placement of your effects.
About 30 years ago, a fellow co-worker began teaching me how to play electric guitar. I believe it was an Aria Pro Strat. He had been playing for 20 plus years at this time and was a very good teacher, he owned a 1958 Les Paul. I have not played since he was in a car wreck in 1990 as he could not return to work. He was however able to continue to play, its just our schedules never allowed the time to take lessons. He passed away in 2011, and since I retired last year, I’d like to take up lessons. I found your article very helpful in selecting an electric guitar. It mentions a lot of things most people do not consider when buying.
Signature Guitar was a Canadian Guitar company, which providing good quality guitars for more than 30 years. They produce high quality electric guitars, beautifully crafted and basses. Their guitars are especially made for Indian weather. The company is situated in Aurora, Ontario, Canada. They are regarded as one of the reputed Indian Guitar brand. The price range starts from 4,999/- onwards (approx).
Paul Landers, of Neue Deutsche Härte band Rammstein has a signature guitar based on his custom-built guitar. It features a mahogany body with a maple cap finished in satin black with silver binding only around the front of the body. The neck is also made of mahogany and features an Obeche fingerboard with no inlays or binding. Hardware includes a hardtail tune-o-matic bridge and Grover locking keystone tuners. The guitar also feature chrome-covered EMG pickups; an 81 in the bridge, and a 60 in the neck. It also only has a single volume control and a 3-way pickup toggle switch.
A musician is only as good as the songs he or she plays - except when you're improvising, of course! And even for those of us who write mostly our own music, there's always room for a repertoire of the classics. Building up your musical library starts with the tablature available in this section, and where it ends is up to you. If you're like most musicians, you'll probably spend your whole life collecting and trying your hand at new music. And with material here for guitar, bass, ukulele, banjo, mandolin and even violin, there's something for virtually everyone. Cover the songs in your own personal style or try your hand at recreating them as they were first recorded; it's up to you.
Original plate reverbs were mechanical in nature. There was a literal plate inside the amplifier, which would transform input signal into vibration. Then you would have a pickup located somewhere near the plate, that recorded those vibrations. Today, such a contraption comes across as relatively crude, but many still love the unique mechanical sound it produces. Spring reverb uses a pretty much exact same principle, only this time you have a spring in there instead of a plate. The biggest improvement a spring reverb offers is reduction in both weight and size of the device.
List of guitar brands that include the most reliable models available. Guitar brands include those from major manufacturers of musical instruments, including Yamaha, Gretsch, Gibson and more. This list answers the question, 'What are the best guitar brands?' Users looking for a new guitar will want to research a variety of different brands to find the one that best suits their needs, based on function and features.
Because overdrive and distortion add a lot of high frequency harmonics to the signal they will quickly muddy up the sound if a large number of notes are struck simultaneously. i.e. full open chords and full barres don't work with overdrive, they muddy up. What you play are simple forms, generally no more than three notes simultaneously. For example an "A" power chord is (high E to low E)

 The type of guitar strings you choose, and how often you change them will not only dramatically affect your tone, but also impact the playability of your guitar. By learning about the different string options available for your guitar, you can find the strings which strike the best balance between great tone and playability. The key components affecting tone and playability come from string gauge, string winding method and the string construction material.

If you've NEVER heard of EZMix for effects, Impact Soundworks Shreddage 2 IBZ or Prominy V-Metal for guitar, or Alchemist Studios Texas Grind for bass, or Impact Soundworks Shreddage Drums for drums, then I would say you're right, (Amplitube 4 is out right now, by the way). You need Kontakt 5.5 for all of this to work though, so if you have this already you need to upgrade.
I was at a friends house and he had a couple of his guitar playing buddies over. We got to talking about guitar repair and setups and such. Then one the guys said “the guy I use is the be...st ever...”, and I was all like, “yeah I’m sure the guy you use is great, but the guy I know is better”. This went on, back and forth for a few minutes, when he blurted out, “I use the Cigainero brothers...”. I said “cool, me too” See More

Pickups are transducers that convert the mechanical energy of a vibrating guitar string into electrical energy by way of electromagnetic induction. It is a fundamental concept studied in physics and electronics that a changing magnetic field will generate a current through a coil of wire. The electric guitar pickup uses permanent magnets and pole pieces to form a steady magnetic field in the vicinity of each individual guitar string. An opposite magnetic polarity is induced in the metallic (steel core) guitar string when mounted above its respective pole piece and when the string moves, the otherwise steady magnetic field changes accordingly. Wire is wrapped around the poles thousands of times to form a coil within the magnetic field to pick up an induced current and voltage.

Rickenbacker basses have a distinctive tone. The 4001 bass has neck-through construction for more solid sustain due to more rigidity. The sustain at the bottom end is particularly striking, and by routing the two outputs from the stereo “Rick-O-Sound” output, the brighter bridge pick up through a guitar rig and the bassier neck pickup through a bass setup, a particularly distinctive bass sound is produced. The 3000 series made from the mid-1970s to mid-1980s were cheaper instruments with bolt-on 21 fret necks. There was also a set neck4000 version in 1975 and 76 (neck set like a Gibson Les Paul) which had a 20-fret neck, dot inlays, no binding (similar to the 4001S) but only a single bridge position mono pickup. (more info needed)
The Squier Vintage Modified Jaguar is a beauty on it’s own. Back in the days the jaguar was used for country music, early rock ‘n roll and jazz, but eventually it has found it’s way onto the stage of surf, funk, alternative, grunge and rock music. The guitar features include a basswood body, maple neck, circuit selector and tone circuit switches, pickup on/off switches, skirted black control knobs (lead circuit) and black disc knobs (rhythm circuit), vintage-style bridge and non-locking floating vibrato with tremolo arm, vintage-style chrome tuners and chrome hardware. A real good guitar for the price. If you want decent and different, this is it!
: : : Does anyone know for sure where these originated. I have been told Vox (the England years) made this flat bodied plank guitar in the skiffle days of early 60's/late 50's. Mine is painted white(by hand) with a large black pick guard that curves to envelope the two chrome "toaster" pickups ,bottom of neck, and three control knobs.The strings have a moveable maple bridge(not secured) and a small chrome hardtail heel.The neck has a zero fret at top and 19 more playing frets.There are dot inlays at the 3rd,5th,seventh,ninth,12th,and 17th frets.The headstock is of natural finish light maple with a top edge cut at a sloping angle like Hofner.It has brass tuning pegs,gears and gear plates and the keys are white plastic.The beautiful short neck is true ,natural maple.Along one of the tuning gear plates is the numbers: 35515 which are etched into the wood. Four bolts without any plate hold the neck base to the plain body and a green decal above the pegs at top face of headstock reads: Shadow. The fret board is rosewoodand is laid on neck without bindings.It has six strings and sounds like a short scale Baritone guitar. It also only has one strap peg at bottom since they used to put the other end of strap on a tuning key. No other holes are seen for any former peg at other end of body(where normally found). Please send any info on this small,early,simple but awesome sounding electric skiffle guitar from England(Vox?).Thanks!!!!! VoteinNovember
×