While National blithely ignored Beauchamp’s electric experiments, their competition – Dobro – was next to enter the electric arena as early as 1933, with the introduction of the Dobro All-Electric. Basically, the All-Electric was a mahogany-bodied Model 37, most usually outfitted with a 12-fret square neck. It had a large lightning-bolt-engraved coverplate, two screen holes, three little holes under the fingerboard, a slothead, and rosewood ‘board with dot inlays. Instead of the usual resonator, this had a large metal plate where the cone assembly would normally be and a Stimson pickup mounted just in front of the bridge, curiously enough with the poles slanted from the bass side near the bridge toward the middle on the treble side.
One important thing to keep in mind about effects pedals is that the signal is doing a lot of work going through the complex electronics in them, and some effects play better as inputs for others. This all means that the order of your pedals does matter to some degree, depending on which effects are in the lineup. You can, of course, experiment to see how different orders affect the sound and that can be part of creating your own signature effects profile. But as a rule of thumb, here’s the basic order you should follow for your first foray into effects chaining:
A second common problem we encounter is a poor mechanical connection. When inserting a cord into a jack, the click you feel is the tip of the cord seating against the metal prong on the end of the jack. With use this prong may spread outward and loose a bit of it's tension. A gentle bend of the prong may be just enough to create a solid connection, however, metal fatigue can dictate the need to replace.
The good people at Cordoba, therefore, sought to make a Spanish-style guitar with the traditional sound of a Spanish guitar, but the slimmer body and slightly narrower neck of a steel-string. They also added in a Fishman-Presys module for switching the guitar from an acoustic sound to an electric (including a built-in tuner), hence the “Fusion” in the model name.
Drop A in D standard variation - A-G-C-F-a-D: Used by Mastodon on most of their first album (Remission) and on some songs on other albums. Also utilized by Periphery on the song "Zyglrox" as well as "Alpha" and "The Bad Thing." Also used on occasion by Black Label Society, who previously tuned it a half-step up, which Alter Bridge also utilizes on some of their songs such as "Broken Wings", "Come to Life", "I Know it Hurts", "Still Remains", "Breath Again", and "All Hope is Gone." Creed, Architects, and Sevendust all use this tuning tuned a half-step down on their songs "Bread of Shame", "Early Grave", and "Home" and "Chop" respectively, with the latter also tuning down a full step for the songs "Death Dance" and "Not Today". Danish industrial metal band Raunchy used this tuning tuned one and a half-step down (F#-E-A-D-f#-B) on the song "Dim the Lights and Run" from the album A Discord Electric. Wage War also utilize this tuning one whole step down for songs like "The River" and "Spineless" off their album Blueprints.
Modulation, in general electronics, means the altering of signal strength. In audio devices, modulation is a control feature that varies the strength of some effect over time to alter tonal properties. Some modulation effects mix ("modulate") an instrument's audio signal with a signal generated by the effect called a carrier wave.[70] Other modulation effects split an instrument's audio signal in two, altering one portion of the signal and mixing it with the unaltered portion.[71]

## Due to distortion's critical function in modern guitar styles, by far the lion's share of stompboxes are distortion units of one kind or another. Most of these feature intensity and tone controls, but often vary wildly in terms of the sounds they create. You'll be amazed at the different types of distortions that can be produced, from rich, creamy, smooth, and melodic sustain to harsh, jagged, and piercing breakup tones. Many distortion units produce a broad range of textures.

National did not seem interested in the project, and, as we’ve seen, Beauchamp and Barth left National that year to begin Ro-Pat-In with Rickenbacker, where they used their ideas on the development of the new Electro electric Hawaiian aluminum “frying pans” and Spanish guitars. Again, some disagreement exists regarding the relative roles of Beauchamp and Rickenbacker in the development of these guitars, but, again that’s a different story. Beauchamp applied for a patent on his “frying pan” on June 8, 1933, and again on June 2, 1934, eventually receiving the patent on August 10, 1937.
A tremolo pedal takes your signal and chops it up, making it sound like the volume is dropping and reappearing very quickly. Imagine what it would sound like whilst holding a note and turning the volume down on your amp and back up again and you’ll get the idea. A tremolo allows you to change the speed at which the volume drops happen and how severe the cut off is. You can have it set to completely cut your sound out or just gate it, which allows a certain amount of sound through at each interval. The BOSS TR2 Tremolo is one of our favourites here at PMT.


This is a very cool goldtop Vox SDC 33. Ultra slim body and neck makes playing extremely smooth and comfortable. Coaxe pickups provide a unique array of tones. Has some natural wear from normal use, like the buckle rash and a chip on the neck finish shown in the pictures. Overall a very clean and well playing guitar with a unique look and sound. Contact us with any questions! Thanks, Fondren Guitars
Being the go-to instrument of popular guitarists like Hank Williams Sr. Neil Young and Jimmy Page (just to name a few), the current production model D-28 continues the Martin Legacy in terms of build and sound quality. Finally, all these features are provided without the inherent maintenance issues and crazy price tags of actual vintage models. If you're looking for a true traditional acoustic then your best bet is to go for the Martin D-28. The MSRP is $3299 but you can get it online for around$2,629.
It’s easy to remove your pickup or pickguard and slide some foam rubber behind the unit. Start with soft foam first, and then increase the density to find the difference you like. Conveniently, the gray foam used in aftermarket pickup packaging makes great damping material: It’s soft enough that you can double it up (see Fig. 1 and 2) to create more pressure on the pickup’s back plate, too. This is a relatively no-frills mod that requires minimal materials and tools.
Frets are the metal strips (usually nickel alloy or stainless steel) embedded along the fingerboard and placed at points that divide the length of string mathematically. The strings' vibrating length is determined when the strings are pressed down behind the frets. Each fret produces a different pitch and each pitch spaced a half-step apart on the 12 tone scale. The ratio of the widths of two consecutive frets is the twelfth root of two ( {\displaystyle {\sqrt[{12}]{2}}} ), whose numeric value is about 1.059463. The twelfth fret divides the string in two exact halves and the 24th fret (if present) divides the string in half yet again. Every twelve frets represents one octave. This arrangement of frets results in equal tempered tuning.


There is dust or corrosion in the potentiometer behind the knob. You need to turn the volume knob between 1 and 11 over 9000 times to wear the track clean again. . If that does not help taking the electronics tray out of the amp (don't break the wires and don't electrocute yourself) to check if the volume potentiometer has any holes. Using a can of compressed air or non-reactive solvent from an electronics store with the thin nozzle tube supplied, blow or flush out the dust. . If it really annoys you and you can't get rid of it, replacing the potentiometer(s) with new sealed ones will overcome the problem forever. or use standard ones and remember to turn the knobs every week to stop dust from settling. . PS. if it is a high powered amp there will be capacitors inside that can seriously hurt you even when the amp is unplugged.
The company initially manufactured only traditional folk instruments,[citation needed] but eventually grew to make a wide variety of stringed instruments, including violins, cellos, banjos, upright basses—and a variety of different types of guitars, including classical guitars, lap steel guitars, semi-acoustic guitars, and solid body electrics. Some of Kay's lower-grade instruments were marketed under the Knox and Kent brand names.


In terms of precedent, one of the best known users of a parlour acoustic is Ian Anderson, frontman of eccentric British prog-rockers Jethro Tull. Here the smaller sized guitar enabled Mr Anderson to sling it off his shoulders, often mid song, to embark on a flute solo or child-scaring facial contortion marathon.  So, if that’s your goal, a parlour is the guitar for you.
In late 2012 I decided that I had all the modern guitars I needed. I’m not gigging much, just writing and recording. There were a couple of vintage guitars I was interested in. A Vox teardrop, especially the Mark IX, and the Fender Coronado. The Voxs turned out to be too expensive for me, especially the Mark IX, which was a 9-string beast meant to sound similar to a 12-string. Those are very rare and priced out of my range. The Coronado, I might be able to afford one day, but I’m not as interested as I was. The new reissues sell for about \$700, but they’re different from the originals in several important ways.
The taper of a potentiometer indicates how the output to input voltage ratio will change with respect to the shaft rotation. The two taper curves below are examples of the two most common guitar pot tapers as they would be seen on a manufacturer data sheet. The rotational travel refers to turning the potentiometer shaft clockwise from 0° to 300° as in the previous visual representation drawing.

## 1967-1969: about the coolest guitar Danelectro ever produced. Has 13 drone strings that move from the vibration of the usual 6 strings. Three pickups, 2 for the 6 stings and 1 for the drone strings. Crinkle burgundy finish, 3 point body shape. Has a "buzz" bridge which similate the sitar sound. The resonation from the buzz bridge vibrates the top of the body and the drone strings. Clear pickguards protecting the drone strings and Vinnie's name on the lower 6 string clear pickguard. Body is made entirely from Poplar, with a semi-hollow construction.

The Supro Spanish Guitar was a non-cutaway archtop built by Regal with electronic components supplied by National Dobro. Except for the fairly modern block-style Supro logo, this was pretty much a typical downscale pressed-top Regal archtop guitar, with a mildly rounded headstock, neck joining the body at the 14th fret, 20-fret rosewood fingerboard, five single-dot inlays, wooden adjustable compensated bridge and a simple trapeze tailpiece. The most distinctive feature was that the guitar had no f-holes. You’ll recall that the ’35 Dobro Electric Spanish was a “conventional” archtop, most likely with f-holes (a comparable National archtop also had f-holes in the beginning, but switched to the non-f-hole design in late ’36 or ’37, following the Supro pattern). The pickguard was typical Regal made of black Ebonoid plastic. In catalog illustrations this appears to have white trim around the edge, but this was apparently company “retouching” to make the pickguard stand out better in the pictures; real examples have plain black ‘guards. The oval, covered pickup sat on a wider oval surround which also held the single volume control. This pickup was nestled down near the bridge. The tuners were Harmony Tune-Rites, with polygonal pot metal buttons. The necks on National Dobro guitars which were entirely made by other manufacturers were glued in. Slightly later, when they began making their own necks and applying them to other bodies, National Dobro Spanish guitars had bolt-on necks.
Like many others, Reinhold Bogner (born in Ulm, Germany, like the EL84 tube!) started his career with Fender mods. He founded his company in 1989 in Los Angeles and succeeded in earning a reputation among guitar amp manufacturers. His brand became famous with models like the Ecstasy 100A and 100B, where "A" stands for American (with 6L6 tubes) and "B" for British (with EL34 tubes). Among its famous users, you'll find Steve Stevens and Steve Vai (apparently your name must be Steve to be Bogner's friend).
The use of two or more mics is likely to result in other phase issues when these mics are combined in the mix, since they will almost certainly be capturing sound waves that reach the mic capsules at slightly different times. Whether such issues are bad enough to cause a problem (or even be heard) depends on the situation. First, if your two mics sound odd and hollow and/or lacking in low-end from the outset, flip the phase of one (usually via a switch on the preamp or afterward in your DAW) to ensure you aren’t trying to blend two mics that are reverse-phase in the first place. If your two-mic sound goes from hollow and thin sounding to fat and full, you had a reverse-phase issue. If it doesn’t improve – or gets worse – you need to consider other remedies. Once you know that both mics are at least in phase with each other, you can improve their phase relationship even further by moving the position of one around until any other sonic oddities are less obtrusive, which is simply determined by finding a pair of positions that are really smoking tone-wise.
Some of the most impressive pieces of equipment come in small packages and in the shape of an item you would not expect to be as good as it is. The proof of this is the deceptively simple looking Mugig Portable Amplifier for Electric guitar, with 10W of power. This piece of equipment is on the big side of small, but is perfect in every single aspect of it, other than the size. The design is simple and understanded, the ease of transport is guaranteed, while the sound takes over the mind and heart of the musician and the crowd instantly. It is possibly the best electric guitar amp that I have gotten to mention on this list.
Residing between your guitar and your amp, your effects pedals make it possible to change up your sound between songs or even verses. A pedalboard makes it easier to manage and transport all those stompboxes. The longer your effects chain, the more helpful a pedalboard becomes. Keeping all your pedals in one place, a pedalboard helps you stay organized and keeps your effects layout consistent.

We round off this list with a relatively modern innovation in the world of acoustic guitars; the ‘baby’ acoustic. As usual, Martin and Taylor have led the way with these particular guitars, which are effectively shrunken down dreadnoughts which focus heavily on their portability and the wide range of musical scenarios in which they can be used. Martin had dabbled in this world before, with its rather odd looking Backpacker, but it was with the LX1 – and Taylor’s subsequent Baby Taylor – that the world began to take note.
By moving up or down one level, in terms of magnetic strength, you can usually add or subtract a little edge from a pickup. If your guitar is too tangy, moving down one pickup level (e.g., from alnico 4 to alnico 2) may smooth it out. If you want to add bite, go with a slightly stronger magnet—like, alnico 5 to a ceramic magnet. The good part is that magnets are both easy to find and inexpensive in comparison to buying a whole new pickup.
Solid state systems grew in popularity in the 80s and 90s, as the digitization of audio signals posed a more reliable and less expensive alternative to tube amplification. In recent years, however, many guitarists have been willing to fork over a little extra scratch to get their hands and their ears on the sounds of the past, on the warm tones that the computers can't seem to capture.

#### This is probably the most iconic guitar effect ever – from Slash to Jimi Hendrix to Mark Tremonti to SRV, the list of players who use wah pedals is almost never ending. Originally created to emulate the muted sound possible on a trumpet, it quickly became an iconic effect in its own right. The sound is pretty self-explanatory – rock your foot back and forth of the pedal to shift the EQ from bass heavy to treble heavy and you’ll get a nice “wah wah” as you play.

There was no “Kent Guitar” Factory. The Kent brand was established in 1960 by Buegeleisen & Jacobson, a musical instrument distributor in New York City. The 500-series models had a metal “K” badge (like the one at left) attached to the headstock of the guitar. The use of a glued-on logo is a good sign that the guitar could appear under another brand name if the manufacturer so desired. The 600-series Kents had the name in metal script letters attached (probably glued) to the headstock. The 500 and 600 series guitars were almost identical. The headstocks were somewhat shaped like those on Fender guitars. Most of those were low-end solid-body instruments.
Late 1944 to about 1949: the bracing was tapered. This stopped in the late 1940s, and was a progressive thing. So unlike scaloped bracing that had a definate endpoint, tapered braces evoloved into "straight" braces by 1949. This is why 1945-1949 Martins are still highly regarded as "better" than their 1950s counterparts, but not as good as the 1944 and prior scalloped braced guitars.
The way you connect your amp, speaker and DI box depends on whether the DI box has a built-in dummy load.If miking isn't practical, or you don't want to find space for a soundproof speaker/mic box, then perhaps one of the available DI options will give you the result you need. I was once reviewing an analogue guitar preamp that provided several programs, both clean and overdriven, and I noted that one of the clean settings sounded really superb. When I checked the manual, I found this was the bypass position! The reason it still sounded good was that the unit was matching the high impedance of the guitar to the medium impedance of the recording system and, for clean sounds, you can get this same effect by using any good-quality active DI box that offers a high-impedance (500kΩ or more) input. A little compression will add density and 'spring' to the sound (experiment with the attack time to get the best 'pluck' sound, as too fast an attack can squeeze all the life out), while reverb will put back the missing sense of space.
Another Martin creation, the 000 shape guitar is almost the perfect halfway house between a dreadnought and a parlour. Its classic hourglass figure meant it sat comfortably on the knee, endearing it to players of folk and other fingerpicking-heavy styles of music. The shape ensured it had the perfect balance between playing and comfort, and was often seen on the lap of no less a player than Eric Clapton. However it wasn’t averse to a bit of heavy strumming when the occasion called, and it’s large bottom end ensured it could keep pace when playing with others.
{ "thumbImageID": "Limited-Edition-1966-G-400-PRO-Electric-Guitar-Ebony/H79032000001000", "defaultDisplayName": "Epiphone Limited Edition 1966 G-400 PRO Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Cherry", "sku": "sku:site51321473136498", "price": "399.00", "regularPrice": "419.00", "msrpPrice": "599.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Limited-Edition-1966-G-400-PRO-Electric-Guitar-Cherry-1321473136498.gc", "skuImageId": "Limited-Edition-1966-G-400-PRO-Electric-Guitar-Cherry/H79032000003000", "brandName": "Epiphone", "stickerDisplayText": "Price Drop", "stickerClass": "stickerEmphasis", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Limited-Edition-1966-G-400-PRO-Electric-Guitar-Cherry/H79032000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Ebony", "sku": "sku:site51321473136358", "price": "399.99", "regularPrice": "424.99", "msrpPrice": "599.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Limited-Edition-1966-G-400-PRO-Electric-Guitar-Ebony-1321473136358.gc", "skuImageId": "Limited-Edition-1966-G-400-PRO-Electric-Guitar-Ebony/H79032000001000", "brandName": "Epiphone", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Limited-Edition-1966-G-400-PRO-Electric-Guitar-Ebony/H79032000001000-00-60x60.jpg", "imgAlt": "" } ] }