Capacitors (often referred to as "caps") have several uses in electric guitars, the most common of which is in the tone control, where it combines with the potentiometer to form a low-pass filter, shorting all frequencies above the adjustable cut-off frequency to ground.[12][13] Another common use is a small capacitor in parallel with the volume control, to prevent the loss of higher frequencies as the volume pot is turned down. This capacitor is commonly known as "treble bleed cap" and is sometimes accompanied by a series or parallel resistor to limit the amount of treble being retained and match it to the pot's taper.[14]

Our production/assemble time frame: 15 - 25 working days since our professional Control Team and Supervisor Engineer will ensure that your ordered guitar is top notch considering the fact that this guitar is intricate to assemble and they check very carefully every detail such as the finish, fret work, pickups, strings. And also, they will test the sound quality. We do not rush up the process of manufacturing your guitar since we would like to deliver to you best quality performance.
In 1995, an effort was made to re-introduce Rickenbacker acoustics, with factory production beginning in their Santa Ana manufacturing facility in 1996. Four models of flat top acoustic Rickenbackers were depicted in factory literature (maple or rosewood back & sides, jumbo or dreadnaught shape). Each of these four models was also available in both six- and twelve-string configurations, yielding a range of eight distinct instruments.[11] (The 760J “Jazzbo,” an archtop model, was only built as a prototype, with three examples known to exist.) It is estimated that fewer than 500 Rickenbacker acoustic guitars were built before the factory shut down the acoustic department in mid-2006.
The vast majority of bass amps in the 2010s can be powered solely by AC mains power, obtained by plugging the amp into a wall socket. Inexpensive practice amps may have the AC mains plug hardwired into the unit. Middle-priced to high-priced amplifiers typically have a removable cable and plug, as used with PC computer towers. The benefits of having a removable cable and plug is that if the cable becomes worn or damaged, a new cable can easily be replaced by a layperson. If a hardwired AC mains cable and plug becomes worn or damaged, a qualified technician or electrician will typically be required to replace the cable and plug. Most amps are designed to work for a single voltage. A small number of expensive bass amps designed for touring professionals have user-selectable voltage, which enables a bassist to play with same amp in North America and Europe. A small number of small combo amps can run on both AC mains power and battery power. This enables bassists to play outside where there is no access to power (e.g., for busking on the street). Amps that are battery powered may have a 12 volt input, enabling the unit to be connected to a car battery with alligator clips.
{ "name": "Vintage Sunburst", "skuUrl": "/Epiphone/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Vintage-Sunburst-1500000014892.gc", "status": "backorderable", "statusText": "Back Order", "skuItemType": "New", "inventoryText": "Available 11-20-2018", "inventoryKey": "available_date", "availableDate": "11-20-2018", "price": 149.00, "isOnSale": false, "msrp": 248.00, "salePrice": 149.00, "easyPayOptions":"0,0,8200002,12 Months Promotional Financing,10/31/2018,Special 12-month financing + $7 back in rewards Valid through,149.0,true,/pages/Gear-Card-Rewards.gc", "formatedIntegerValue": "149", "decimalValue": "00", "listPrice": 149.00, "isPriceDrop": false, "priceDropPrice": "", "savingsAmount": 99, "discountPercentage": 40, "promos":["coverageEligible","freeShipping","international"], "warranty": true, "sku": "site51500000014892", "shipToStore": false, "displaySku": "J40301000004000", "displayId": "1500000014892   POS #: 112318357", "serialized": false, "stickerDesc":"Top Seller", "stickerDisplayText":"Top Seller", "shipsFree":true, "condition": "New", "commerceType": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/J40301000004000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"true", "invMsgPreOrder":"false", "invMsgPromiseDate":"11-27-2018", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Vintage-Sunburst/J40301000004000-00-140x140.jpg", "styleImgAlt": "Les Paul Special Vintage Edition Electric Guitar Vintage Sunburst", "freeGiftWarning":false, "freeGiftWarningTips":"", "kitCarouselItems": [], "availableInStoreOnly": false, "isShipsInternational": true, "checksum":"93895071200", "restrictionType":"", "restrictionError":"" ,"storeInfo":[ { "storeName" : "La Mesa", "storeStatus": "Ship to Store" } , { "storeName" : "San Ysidro", "storeStatus": "Ship to Store" } , { "storeName" : "San Marcos", "storeStatus": "Ship to Store" } ] }
As a side note, many guitarists refer to the vibrato as “tremolo” or, worse yet, “whammy bar”. (I sometimes do, too, when my mouth is moving unaccompanied by my brain) Vibrato refers to varying the pitch while tremolo is varying the volume. Leo Fender himself is largely responsible for the misuse of the words. He called the bar on his guitars the “tremolo” and even had the tremolo effect on his amplifiers labeled as “Vibrato”.
So fun...I like...Let me start off by saying I'm not even a game person I bought this game for my son than watching him play it I took over and couldn't stop playing it I played it non stop until I beat it the content and visuals are great...The only downside was that I was so addicted to this game that I finished it in about one week, but I already am planning on playing it again on a higher difficulty and with a goal of finding more of the hidden treasures that are sprinkled throughout the game.
In jazz big bands, popular during the 1930s and 1940s, the guitarist is considered an integral part of the rhythm section (guitar, drums and bass). They usually played a regular four strums to the bar, although an amount of harmonic improvisation is possible. Freddie Green, guitarist in the Count Basie orchestra, was a noted exponent of this style. The harmonies are often minimal; for instance, the root note is often omitted on the assumption that it will be supplied by the bassist.

This guitar follows after the tried and tested formula of old Stratocaster design, from the double cutaway alder body to the bolt-on maple neck, down to its triple single coil pickup configuration. The scale length follows after traditional builds at 25.5", while the neck profile (modern C) and narrower nut width of 1.65" makes this guitar viable for modern players. While it doesn't have vintage voiced pickups, the default pickups are not so bad either, and will give you the distinctive Strat tone that almost everybody loves.
It depends on what purpose the noise suppressor will fulfill. You may need more than one placement depending on your purpose. If you position it behind the tuner, it will remove any unwanted noise from the guitar signal before it gets modified with the pedals (this is the most common placement). Guitarists also use the noise suppressor or noise gate pedals after an overdrive to cut the riff sharply.
Vibrato design is slightly changed and enhanced with the addition of block saddles for adding a fair amount of firmness to the tone. Likewise, they also give a precise breakpoint for the strings. Talking about pickups, pac 112v is equipped with 5-way blade pickup selector. Similarly, master tone and volume controls are also provided for the neatest output.
I think singing with confidence without too much doubt was a satisfying thing. It was, artistically, very satisfying to be covering subject matter that means something to me. I think a little bit of that was getting to know yourself. And just the simple fact that I was ready to do it now. Everything else I'd done since going out on my own in '87 has been absolutely amazing to me, and I feel like the luckiest guitar player alive, and I am very grateful.
Festive music track with cheerful and happy mood, with “We Wish You A Merry Christmas” song melody. I’ve included in pack different logo and looped versions of this track, for your comfortable using. This celebratory track can be used for Winter Holyday projects, children arcade games, as New Year jingles, advertising and Youtube commercial video. Enjoy!

Browse guitar sheet music for all levels of guitar players. Whether you're a beginner starting from a clean slate or a guitar shredder gigging on a nightly basis, our guitar sheet music collection has everything you need. Find thousands of guitar method and guitar etude books as well as your favorite guitar songbooks from Jimi Hendrix, Stevie Ray Vaughan, Metallica, The Beatles and more. Looking for digital guitar music, guitar chord books, guitar play alongs and guitar transcriptions? No problem. Take a load off, put up your feet and browse and buy guitar sheet music today.
Electronic instruments are well known for their great versatility and all of the amazing sounds that they can produce. In many cases, those effects all come down to skillful use of the right pedals by a talented musician. When you're equipping your pedalboard, some of the first units you should look at are delay and reverb effects pedals. Delay pedals enable you to put a note on a timer and have it come back a few measures later. They're perfect for holding off a chord, then having it kick back in with a new sound layered in on top of it for cool combination effects. For example, you might mix a long, sustained note together with a more complex riff to briefly become your own rhythm guitarist. You can play a chord against itself to double up into a deeper, richer tone, or even simulate an echo for atmospheric effect.
Route the body. You’ll need to make a cavity (a hole that goes partly through the body of the guitar) in the back of the guitar to fit the electronics for the volume, tone, pickup selection controls. You will cover it later with a bit of material (usually hard plastic). You’ll also need one cavity in the front of the guitar for each of its pickups. Rout the pickup cavity (or cavities) to the depth recommended by the manufacturer.[9]
The question here is how high to make the bridge. Well, this is personal choice. Find somewhere were the string doesn’t buzz on any fret from being too low, but low enough that you can play up and down the neck easily. There’s usually a sweet spot where you can just start to detect some buzzing and you can leave it just a tiny bit higher than that. Now do the exact same procedure for the high (thin) E string end of the bridge. Play the guitar a little bit to see if any of the other strings are buzzing. If, say, the A string is still buzzing, then raise up the end of the bridge nearest to that string a little bit ( a small amount of buzzing is often OK as long as it doesn't bother you too much and isn't heard through the amplifier - this a bit of a personal choice thing). OK, that’s step 2 finished. Your guitar should be nice and playable now. However, it may not seem to stay in tune very well. That’s because the intonation might be off.  

So you’re thinking about building an electric guitar. Well, it’s a very rewarding experience when it’s done right, and you have the ultimate freedom to make it whatever you want. On top of that, it can be a money saving alternative to the hefty price of a good instrument, if you’re willing to invest your time. Or if you’re just planning on undertaking a fun project, it can certainly fit that bill too.
Everything about the shape and feel of the S6 Original is meant to be as close to familiar acoustic guitars as possible, including its playability, which is brought about by its 25.5" scale length, 1.8" nut width and 16" fingerboard radius. Tone wise, you're getting a crisp yet warm tone thanks to its pressure-tested solid cedar top, which also adds to the overall earthy appeal of the instrument.
The golden question is: What is the difference between acoustic and electric guitars. The primary difference between the two types of guitars is that acoustic guitars produces sound entirely through vibration. Its sound is emitted through the vibration of the string when it’s plucked back and forth. Electric guitars, on the other hand, are powered through electricity and electromagnetism generated through its components are what drives the sounds that come out of it.
Repair body wings. These wings form the main body shape and may have been broken by dropping the guitar or other damaging methods. If you do not properly glue in the wings you will need to use extra caution as to not break the bond. Repairing wings or any body wood is rarely necessary, especially on a thick guitar body such as a Les Paul Standard. It may be needed on a smaller bodied guitar much like a Les Paul Junior.
Most metal guitarists would kill to have half of the power and precision of James Hetfield’s right hand, not to mention his ability to write the most devastating riffs known to mankind, from “Seek and Destroy” and “Creeping Death” to “Enter Sandman.” Of course, most musicians with skills comparable to Hetfield’s have such big egos that they become the targets of our murderous intentions. That’s not the case with Hetfield.
{ "thumbImageID": "ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst/J57125000001000", "defaultDisplayName": "Alvarez ABT610E Baritone Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51500000217496", "price": "399.99", "regularPrice": "399.99", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Alvarez/ABT610E-Baritone-Acoustic-Electric-Guitar-Black-1500000217496.gc", "skuImageId": "ABT610E-Baritone-Acoustic-Electric-Guitar-Black/J57125000002000", "brandName": "Alvarez", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/ABT610E-Baritone-Acoustic-Electric-Guitar-Black/J57125000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Shadow Burst", "sku": "sku:site51500000054240", "price": "349.99", "regularPrice": "399.99", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Alvarez/ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst-1500000054240.gc", "skuImageId": "ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst/J57125000001000", "brandName": "Alvarez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst/J57125000001000-00-60x60.jpg", "imgAlt": "" } ] }
{"eVar4":"shop: amplifiers and effects","eVar5":"shop: amplifiers and effects: effects","pageName":"[mf] shop: amplifiers and effects: effects: multi effects pedals","reportSuiteIds":"musiciansfriendprod","eVar3":"shop","prop2":"[mf] shop: amplifiers and effects: effects","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop1":"[mf] shop: amplifiers and effects","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"multi effects pedals","prop5":"[mf] shop: amplifiers and effects: effects: multi effects pedals","prop6":"[mf] shop: amplifiers and effects: effects: multi effects pedals","prop3":"[mf] shop: amplifiers and effects: effects: multi effects pedals","prop4":"[mf] shop: amplifiers and effects: effects: multi effects pedals","campaign":"directsourcecode2","channel":"[mf] shop","linkInternalFilters":"javascript:,musiciansfriend.com","prop7":"[mf] sub category2"}
This guitar follows after the tried and tested formula of old Stratocaster design, from the double cutaway alder body to the bolt-on maple neck, down to its triple single coil pickup configuration. The scale length follows after traditional builds at 25.5", while the neck profile (modern C) and narrower nut width of 1.65" makes this guitar viable for modern players. While it doesn't have vintage voiced pickups, the default pickups are not so bad either, and will give you the distinctive Strat tone that almost everybody loves.
Compressors are available as footpedal controls and can be used as an effect on electric guitar signals, for example. They can be used to obtain greater sustain for a string by setting the gain high and allowing the compressor to keep the output signal at a more-or-less constant level until the natural sustain of the string drops the signal below a certain threshold.
8e FRETTE HAUTEUR La hauteur des cordes est réglée lors de la fabrication des guitares et des basses Ibanez. Néanmoins, plusieurs facteurs peuvent provoquer la variation de hauteur des cordes d'un instrument. Les guitares sont sensibles aux variations de température et d'humidité. Une hauteur de cordes trop importante peut rendre l'instrument difficile à...
In 1970, B.B. crossed over to the white rock audience with “The Thrill Is Gone.” In 1988, he virtually repeated the trick when he recorded “When Love Comes to Town” with U2. Always the humble student of the instrument, B.B. King became jazzier and better than ever as his life and career continued well into the new century. His loss earlier this year was deeply felt by the music community and, particularly, by the guitarist he influenced.
Apple GarageBand comes free with all new Macintosh computers, and it only runs on Macintosh. There is no "GarageBand for Windows". But Apple also has a cut-down version of GarageBand for iOS (iPhone and iPad) that does quite a bit and can be used professionally on stage and in the studio if you also purchase an iOS-compatible external audio interface.
O WOW!...I love...Fallout 4 is a great game like the rest of the fallout series but if your a fan of the series u will be kinda of down that the choices u make don't affect the outcome of the game because they made more of a story they wanted to tell but don't lose hope still a good game and they might make a sequel to new Vegas and there just might be a Multiplayer for new Vegas 2....The world is so large and the gameplay non linear (which is good and bad), I find if I walk away from the game for a while, I have to spend a lot of time figuring out where I was and where I stashed things when I come back to it later.
We saved the most affordable amplifier for the last. This Donner electric guitar amp might have only 10-watts, but it does not lack other features. The controls include Gain, boost Select Switch, Volume, Treble, Middle, Bass and are pretty intuitive. The tone is clean and damn big for such a small model. Other than that this model also has 3-Band EQ, 1/8″ Auxiliary Input Jack for Jam-Along with Media Player and, of course, the handy-dandy Headphone Output Jack for Silent Practice (unless you want to be evicted from your apartment for practicing days on end). Best practice amps are not best just because you can practice in your basement and never move the thing. They are pretty functional and easy to carry around. That’s why Donner put durable, hard material on the edges of the amp and a pad of rubber makes it more sturdy. With that your amp will be pretty much indestructible.
Versatile- many of the practice amps today have “AUX” (Auxiliary) inputs for your electronic music devices like your iPod, phone, or tablet computer. This is essential for learning songs because you can pipe your song from your device into your practice amp and play along either out loud or with your headphones in private. With so many music apps out today for iPhones and Android devices, you can also connect the headphone jack of your practice amp to your personal device to learn new songs and/or record your performance! Check out Ultimate Guitar Web on Google Chrome
Reverb effects are another staple in the toolbox of guitarists across all genres. Just like how delay effects produce a sense of depth and space, reverb effects provide the same ability, but with a different approach. Frequently, especially in modern music, reverb effects are so subtle that it’s hard to even notice that they are there. It’s only when they are removed do we realize that suddenly the sound has become too “close” sounding.
Alongside the Stratocaster, Les Pauls have defined rock ’n’ roll. Everyone from Jimmy Page to Slash to Zakk Wylde has wielded one of these, and the guitar’s fat, creamy tone with near-endless sustain is instantly recognizable. Not everyone can afford a bona fide Gibson, though, but the Epiphone Les Paul Standard makes those sounds accessible to most of us.
I also didn’t mention a tuner, but that’s because a tuner really isn’t an effect. If you use one, the ideal location is in the very front of the signal chain right after the guitar as you don’t want the signal going into the tuner processed by any effects that might affect the tuner’s accuracy. Even better, get a loop switcher with a separate tuner output that keeps the tuner entirely out of the signal chain until you need to use it and that will mute the signal so the audience doesn’t need to suffer while you make adjustments.

Finally, their taper. Taper refers to the gradual increase or decrease of the pots ohm as you adjust it. There are two types of pot taper, Logarithmic (Audio) and Linear (Lin). The human ear hears in a logarithmic manner, so in a gradual increase or decrease, whereas linear, to our ear sounds almost more like an on/off. Which you use is completely up to you, many players prefer a linear volume pot for example, but I find that a quality logarithmic pot in both volume and tone positions offers more scope for adjustment, if using a quality pot that is! Low quality audio taper pots, in my experience, offer unreliable tapers, often not providing a even, gradual adjustment as you roll off or on. A guitar's volume and tone pot can bring out so many great sounds from your rig, it offers versatility to your sound, and I love pushing an amp hard and finding those sweet spots on the guitar's controls to really capture a great tone. So I feel that's why a quality logarithmic pot with a perfectly gradual taper is an incredibly important component in the electric guitar. 
There are just a few minor differences. For example it has a bolt-on mahogany neck instead of a set neck, and the fretboard is made of rosewood rather than expensive ebony. We don’t really care about that, since rosewood actually is really good for fretboard since it’s naturally oily. You don’t want a super dry fretboard. It’s good for the sound too, since it captures some extra overtones that make your tone fuller, nothing goes to waste!
The original  Owner purchased this guitar new at Ideal Music in Atlanta and loved her for the last 50 years. Vintage 1967 Gretsch 6120 Chet Atkins Nashville model,factory bigsby replaced "kill switch" tip (the white one) I have an original tip now, to lazy to take new pictures...and reproduction armature inside body for string mute / Muffler system...SEE MORE HERE...
The Yamaha LL16 gives you high-end features for a lot less money, starting off with its solid Engelmann spruce top and solid rosewood back and sides. This all solid body results in richer and more detailed acoustic tone, something that you will have to pay top dollars for from other acoustic brands. It also sports a slightly smaller body that gives it an elegant appeal, adding to its already favorable affordable price and top-tier specs.
The SD is a classic. This had a more exaggerated Jazzmaster shape than the T-60. It had a dramatically swept back lower horn, and an offset pair of waists, looking as though it’s been slightly melted. These had bolt-on necks with the elongated Strat-style head, with round logo stickers. A rectangular plastic control panel was mounted above the strings, with large thumbwheel controls and on/off rocker switches, while a large-ish pickguard was mounted under the strings. The controls on the SD-4L were especially interesting, taking their cue from the Italians, no doubt. The thumbwheels were for volume and tone, while there were a total of six rocker switches. Four of these were on/off for each of the four pickups, but in between were two more. Their function is unknown, but a good guess would be phase reversal between the front and back pairs of pickups. Both models had the rectangular fingerboard edge inlays. With “L” designations, both had vibratos. These consisted of a fairly simple bar for string attachment with a series of springs behind it, all covered with a hinged metal cover. The handle was extremely long. Pickups were the beefy tall rectangular type with metal cases and black plastic center tops with exposed pole pieces (these could be screws or squares). The SD-4L had four pickups, in two pairs, while the SD-2L had two. If I couldn’t have a Spectrum 5, I’d be looking for one of these (I am!).

The Boss GT-1000 Guitar Effects Processor is by far the best multi-effects pedal that the team at Boss have ever come up with. This is jam-packed with the entire back catalogue of Boss stomp box effects as well as tones from the coveted "500" series Delay, Modulation and Reverb multi FX pedals. So, you have over 116 types of effects to create music with – making it a no-brainer for Boss fans in general and those who need a huge array of expertly crafted FX.


The Old Standby is another model beloved by generations of harmonica players. Up until the 1990s, this model was a quality instrument made in Germany on a wood comb. Where the Marine Band was the choice of blues players, many country music players such as Charlie McCoy preferred the Old Standby. In the 1990s, Hohner began manufacturing this model in China on a plastic comb with a significant decrease in quality. Among harmonica fans the downgrade remains unpopular.[26]
That really depends on what you are going for. There are good arguments for before everything and right after the tuner, but also for after the distortion and before your modulation pedals. If you put yours right after the tuner in the front of your chain, you can equalize your guitar tone before it hits anything and adjust your pedals accordingly.
It doesn't even seem to matter which kind of Guitar amp you have or when plugged into any PA system. This guitar is a keeper. it comes with Godin Nickel Strings which is why unplugged it may sound too tinny to some ears, but after changing to Elixer Acoustic Strings, it sounds much better unplugged and really shows off plugged in. It now can give my Acoustic six strings a real run for my attention. At gigs and open mics, people come up and ask,,,what the Heck is this Bruce? Looks and sounds amazing. My only wish is that it had the same Pick-up system as on my A6 Ultra, two separate Pick Ups and Controls and two 1/4 in outputs.
No matter whether you used method A or B, you can now go about measuring the neck bow. This is done by measuring the string height (the gap between the ruler/string and the top of the fret) at about the 8th fret. There is a lot of debate over how straight a neck should be, and in fact it really is personal choice, but a height roughly the same as the thickness of a B string is a good starting point. Personally, I use a 0.012” feeler gauge to do this, but you could use a B string. Simply slide the feeler gauge/B string into the gap to see if it is too big/small.
Ovation guitars are produced in the U.S. as well as in Korea and China. Those models in general have a wooden top. Recently Ovation significantly reduced the production of U.S. made Ovation models. From 2010 on better models (e.g., Legend, Elite, Custom Legend, Custom Elite) used to be available, both, made in the U.S. and made in Korea. Before that, the mentioned models were U.S. made. In recent years many U.S. made guitars could be identified by the LX in the product name (e.g., Legend 2077LX), whereas the Korean-made version of the same guitar had AX in its model name (e.g., Legend 2077AX). Again, this name-system has not been used throughout the whole guitar model range (e.g., Ovation 1617ALE). Nowadays only a few U.S. made models are being produced, mostly signature and limited edition models (e.g., Custom Legend 1769-ADII Al DiMeola). Production of the standard model range of Ovation guitars in the U.S. has been seized.[24]
While Gretsch is known for semi-hollow and full hollow body guitars, and it is only fitting that one of their semi-hollow chambered body models make this list, specifically the Gretsch Electromatic Pro Jet Bigsby. Being part of their Electromatic line, brings with it all the Gretsch goodness minus the premium appointments, at a very accessible price point. It is a true archtop thinline guitar, that passed the same attention to quality and detail that more expensive Gretsch guitars also go through.
Acoustic guitars that have been fitted with a pickup can be recorded using the same techniques as standard electric guitars when plugged into an amp. Interesting sounds can be created by mic’ing up an acoustic guitar and sending the sound through an amp. This can be done live – although you should be aware of feedback – or a previously recorded acoustic track can be re-amped and used exclusively, or mixed with the original acoustic track. You can get some really gnarly and original ‘electric’ sounds with creative use of overdriven acoustic guitar; it’s especially good for slide playing.
As both the British invasion and the 1960s came to an end, Rickenbacker guitars fell somewhat out of fashion; however Rickenbacker basses remained highly in favor through the 1970s and on. Perhaps as an echo of the past, during the late 1970s and early 1980s, Rickenbacker guitars experienced a renaissance as manyNew Wave and jangle pop groups began to use them.

{"product":{"id":"L20582","stock":"backorderable","price":"899.00","name":"Slash Firebird Limited-Edition Electric Guitar","download":false,"sku_id":"L20582000001000","checksum":"565047124900","rep_id":"site51500000000211665","displayId":"1500000000211665","sku_display_id":"1500000218333","sku_rep_id":"site51500000218333","gc_pro":false},"category":"Electric Guitars","pageName":"product_detail","subcategory":"Solid Body Electric Guitars","dept":"Guitars"}
Now that we’re done with the construction, let me discuss the pivotal aspect of playability itself. Having conducted scores of guitar lessons both online and offline, I am for one well aware of the fact that it only takes a few tiresome sessions with a bulky, full size guitar to scare them away from their lessons forever! Therefore, your first ever guitar choice is extremely important. A beginner’s guitar needs to be user-friendly and high on playability. On both these accounts, the Davisson Full Size Black Electric Guitar scores high. Not only is it lightweight and comfortable to wrap your fingers around, but also has a very neat and simplistic design to enables beginners for learning faster. The presence of a single Humbucker Pickup and the invariable absence of a pickup toggle, is not a hindrance but in fact a positive aspect of getting your grasp over your first electric guitar.
This guitar sounds tighter and is less loud than a dreadnought. But its construction warms its tone considerably. Its owners say that its tone is well balanced – clear and punchy but still warm. It offers clarity in the higher registers, but some boom in the lower registers. For that reason, the LL16 is suited to almost any style of playing. It will not, however, be as punchy as the Taylor 210 or as round sounding as the Blueridge.

{"pageName":"[gc] pdp: ibanez 1984 1984 ibanez destroyer i red solid body electric guitar","reportSuiteIds":"guitarcenterprod","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","events":"event3,prodView","evar51":"default: united states","prop5":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop6":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop3":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop4":"[gc] shop: guitars: electric guitars: solid body electric guitars","products":";113668304;;;;evar65=null-Guitars-Ibanez","linkInternalFilters":"javascript:,guitarcenter.com","channel":"[gc] shop","prop7":"[gc] product detail page"}


* 3 most basic reverb modes: Room: Simulates the spaciousness of a room; Hall: Simulates the spatial dimension of a music hall; Plate: Simulates the unique reverberation character only coming from a plate reverberator. * One reverb control balances the dry/wet signal, simple enough to dial in the perfect amount of reverb for your tonal needs. * True bypass for zero tonal coloration. * Extreme mini size for great compactness. * Heavy-duty metal casing for great stability and durability; Connectors include input, output, and power supply; Powered by 9v DC. W/ a 6 inch patch cable included. SONICAKE Digital Reverb is reverb pedal designed to add dimension and spaciousness to your tone. It is extremely straight-forward to use with only one “Reverb” knob to adjust the balance between the raw d.
The ghost Hexpander MIDI interface system adds MIDI capability to almost any guitar or bass.  Plug your guitar into pitch-to-MIDI converters by Roland or Axon and enter the MIDI sound universe.  The Hexpander MIDI interface provides responsive and accurate tracking unequaled be any other system on the market today.  Check out how affordable and easy it can be to make MIDI part of your music making.

You might have read our review about the C40 GigMaker kit from Yamaha earlier on. This is a similar guitar, but it’s the C40II, and the black color makes it a limited edition instrument. The inlay is less “traditional” looking. Instead of an ornate “rosette” style, the inlay is a stripe pattern all the way around the sound hole, making the guitar look somewhat “jazzy,” to use a more descriptive term. So if this is the look you prefer, read on for more details.


Fender Kingman "C" Custom Shop Acoustic/electric in Fiesta Red, 1 of 150 worldwide. This was a limited production that came out of the custom shop in Hartford, CT. Has a Fishman pickup. Not a nick, ding or blemish will you find on this guitar, almost museum quality. Comes with original Fender case(perfect shape), Certificate of authenticity and other paperwork and allen wrench. Ships to the US only.
One difference today is the number of big-name guitar brands that make affordable acoustic and electric guitars, which are often versions of their pro-level instruments. These days, you can own a Les Paul or a Stratocaster as a beginner or intermediate player. Of course, they aren’t the same as the Gibson or Fender flagship models, but they are still darned good guitars based on those designs.

Definitely, Diary of a Madman is like…the groundwork for so many great songs out there today. And if you listen to that live solo after Suicide Solution, which is only done live, it's just crazy what he could do that you didn't think he could do. If he was still alive, even if he left Ozzy, we would have seen even better stuff from him. Crowley and Crazy Train were actually more watered down marketable songs. That's more or less why Randy was GOING to leave Oz in the first place.


The bass guitar has a long neck (scale-length) and thick strings. The open strings of the bass guitar corresponds to the four lowest strings of the guitar and are pitched an octave lower. The standard bass has four strings though five and six string basses are available which extends the range of the instrument. Though the bass guitar is the bass instrument of the guitar family and the double-bass is the bass instrument of the orchestral string family their similar roles have drawn bass players to both instruments.

As with other plucked instruments (such as the lute), the musician directly touches the strings (usually plucking) to produce the sound. This has important consequences: Different tone/timbre (of a single note) can be produced by plucking the string in different manners and in different positions. For example, plucking an open string will sound brighter than playing the same note(s) on a fretted position (which would have a warmer tone).
Stripped holes: small holes without much tension on them (i.e. pickguard screws) can be repaired with super glue (gel stuff). Put some glue in the hole and screw the screw in about 1/2 way. The glue will not stick to the plated screw, and will form threads. More severely stripped holes or holes w/ more tension on them (i.e. strap button screws) require pieces of toothpick be glued in w/ wood glue. Larger holes w/ alot of tension (i.e. neck mounting screws) require the hole be drilled out and a hardwood dowel glued in place.
The more solid wood there is, the better the overall resonance, sustain and tone of the acoustic guitar. Solid wood, specially those used on the tops of acoustics, also resonate better as it ages. The downside to solid wood is mainly its more premium cost, and not to mention it uses more wood resources than laminate wood. Solid wood is also more prone to damage, so they require extra care especially from changing weather and humidity. Laminate woods are more affordable, and they are also more sturdy and resistant to damage. On the flip side, they will lack the resonance and sustain of solid wood, but this can be a good thing if you're looking for vintage mid-range focused tone.

The Fender Hot Rod Pro Junior III is a good example of what the older style beginner amps used to entail. The initial price tag is much higher than the typical beginner amps popular today, but it is also a better made, better sounding tube amp. The Hot Rod Pro Junior III can be cheaper in the long run for guitarists that want to eventually do professional work. Most beginner amps are not powerful enough or sound good enough to quite cut it as a professional amp. The Hot Rod Pro Junior III is a simple amp that provides the bare essentials to get a professional level sound. Going the Hot Rod Pro Junior III route is a bit less conventional for beginners, but it is a solid option to consider if plans of recording or playing live lay in the future.
You're headed in the right direction - don't stop! yes, the keyboardist should control vibrato directly with the fingers, not automatically with an LFO. The more you rely on the technology to play the music for you, the worse your results will be in the long run. Is your intention to emulate a guitar, or to achieve a similar kind of lead expression and sound control during playing? Because these two are very different.
Next in line after pitch shift/harmonizer and envelope follower effects are pedals that directly interact with the pickups’ output levels, such as vintage fuzz, treble booster and Octavia/fuzz octave pedals. As with the dynamic filter pedals, placing any other effects that compress the signal in front of these pedals will limit their overall performance.
As has already become apparent, the resonator instruments which made both the National and Dobro names in the late ’20s and ’30s were not the only effort underway to increase the volume of the guitar. The ampliphonics found immediate acceptance among Hawaiian players, notably Sol Hoopii, the very first to record with them when he used a prototype in his first session for Columbia on October 18, 1926. This was used on “Farewell Blues.” But they still didn’t satisfy the desire of orchestra guitarists to get out of the rhythm section. In addition to metal resonator cones, electricity was waiting in the wings, and National, Dobro and National Dobro would play a significant role, both directly and indirectly, in that ultimately triumphant development.

The Japanese copy juggernaut got off to a fast start, and the second major Univox guitar was the Lucy, a lucite copy of the Ampeg Dan Armstrong, again produced by Arai, introduced in 1970. This guitar had a surprisingly thin bolt-on neck (especially compared to the Ampeg original) and a slightly smaller body. The fingerboard was rosewood with 24 frets and dot inlays. This had a fake rosewood masonite pickguard with volume, tone and three-way select. Like the Ampeg, the Lucy had a Danelectro-style bridge/tailpiece with little rosewood saddle. Unlike the Ampeg – which had Armstrong’s groovy slide-in epoxy-potted pickups – this version had a pair of the chrome/black insert pickups jammed together at the bridge. Other Japanese manufacturers also made copies of the Ampeg lucite guitar, notably carrying the Electra (St. Louis Music) and Ibanez (Elger/Hoshino) brand names, with versions of the slide-in pickups. In ’71, the Univox Lucy (UHS-1) was $275 including case. Just how long the Lucy remained available is unknown, but it probably did not outlive the original and was gone by ’73 or ’74.
Dorado is a line of Japanese made guitars imported and sold by Gretsch in the 70's. I am looking for a 5965 which is the smaller of the steel string line, had a sunburst finish, sealed tuning pegs and an adjustable bridge. The market worth is between one and two hundred dollars depending ....... Please post if anyone knows of a real good one with original case.
The company was within three months of going out of business before it was bought by Henry E. Juszkiewicz, David H. Berryman, and Gary A. Zebrowski in January 1986.[18] Gibson's wholesale shipments in 1993 were an estimated $70 million, up from $50 million in 1992. When Juszkiewicz and Berryman took over in 1986, sales were below $10 million.[19] New production plants were opened in Memphis, Tennessee, as well as Bozeman, Montana. The Memphis facility is used for semi-hollow and custom shop instruments, while the Bozeman facility is dedicated to acoustic instruments.[20]
It is a German company that manufactures bass guitars. Making a really good bass guitar is a difficult task. However, Warwick bass guitars have really mastered this daunting task. The growl of the bass, and its hollow and beautiful resonating tone is a striking feature of the bass. The company employs stringent quality control methods in wood seasoning, cutting, and resonance engineering. It is highly regarded among bassists and has attracted many notable artists like Robert Trujillo (Metallica) and Adam Clayton (U2). One of the greatest things about Warwick is that they manufacture guitars for everyone, from amateur hobbyists to professional players. If you are new into electric bass guitars, then Rockbass Corvette Basic and Streamer Standard Electric Bass guitars are great options for a rocking start.

View a complete range of budget friendly electric guitars over at PMT Online today or call in to your local PMT store to see a full range. We have many electric guitars spanning all budgets, styles and genres including a complete range of guitar starter packs. Alternatively, call 0151 448 2089 to speak to one of our guitar experts to discuss your needs.
In the end I decided to go with the .033μ. Everything larger sounded too wooly to me on the neck pickup. If I didn’t play much EBow, I might even consider the .022μ. But you might make a different choice, especially if you were using brighter pickups. You won’t know for sure till you try it out with your instrument, amp, and hands, but I hope this gives you some idea of what to expect.
AGE CAN’T HINDER YOU – Working off of muscle memory and visual assistance, ChordBuddy is designed for players of every age. In fact, ChordBuddy is well-suited for those looking to play guitar with arthritis, offering a pain-free method of playing your favorite song. Utilizing ChordBuddy also allows you to learn the guitar on your own, eliminating the need for long guitar lessons with an instructor, which can result in prolonged joint pain.
• I like to insert a compressor after this, to add some sustain and even out the guitar's dynamics, for a more consistent distortion sound. So for the second insert slot, choose Dynamics/Vintage Compressor, then click on the insert's Edit button to see the compressor's interface, and set up the parameter values as desired. A good starting point would be Input at 17 and Attack at 8.9, with Punch and Auto set to On. You'll probably need to adjust the Input (effectively the Threshold in this case) according to the level of signal coming into the plug‑in. Set the Output to a level that's as high as possible, but doesn't approach clipping.
The auctions continue on our eBay store, including last remaining production samples of several models, and other unique instruments, including made in Japan JP models, Triturador basses, Tony Campos Signature Tremor basses, acoustic guitars and accessories. Check out the current listings, there will be new items posted every week: http://bit.ly/1caL5ah
@BLAKTORX - Charvel is a great brand for metal and shred that is really starting to regain some prominence in the music world. I really like the Pro Mod Series. Music Man, too, makes some good gear, but I tried to keep my list to 10. The Ibanez GIO series guitars are good for beginners. Seems like you're into metal. In that price range you might also check out the Jackson JS Series.
I believe its an 80's model it has some wear n tear but makes it look good and ventig. But there is nothing on it but the bently sign on the headstock.its jet black has a bridge not string through. Two hummbuckers I guess. A treble and rhythm switch up by the neck on the top. It is a 22 fret with pearl inlays. Someone shoot me an email n ill send picks of it. Just want to know what I got my hands on.
Flanger – a time-based effect likened to the sound of an aeroplane taking off and landing. The “whooshing”effect is created by feeding the output of the guitar tone back in on itself with a very short delay (usually less than 20 milliseconds) causing comb filtering (boosts and cuts along the frequency range). The delay time is then varied which causes the comb filter to move up and down the frequency range.
Chorus pedals actually make your guitar sound like there are a variety of different guitarists playing the same thing that you are playing, but with a different guitar and slightly out of time with you. This effect makes everything you play sound a little bit ‘warbly’ and thickens up your guitar or bass lines. We recommend experimenting with these as you can use them subtly to add weight to your sound or as a full-blown effect that completely takes over your signal.
Roger McGuinn's sparkling, chordal 12-string Rickenbacker riffs on the Byrds' early hits were the sonic bridge between folk and rock – and an irreplaceable color in rock's palette: Every indie band who's more interested in beatific strumming than screaming solos owes him a debt (the striking break in "Bells of Rhymney" could be on a Smiths record). McGuinn could do a lot more than chime, however, as demonstrated by his still-astonishing psychedelic-raga-Coltrane licks on "Eight Miles High."
Post on February 14, 2013 in the RRF Forum:[12] “When John Hall so graciously let me have the license to build Rickenbacker Acoustics back in ’06, I brought a truck to RIC headquarters and loaded it up with all of the remaining wood for Rickenbacker acoustics, in order to free up some shop and storage space in Santa Ana. There was enough undamaged wood for about 40 guitars, and I’ve reached the end of the line with my RIC acoustic builds. I’ve decided to let my license to build Rickenbacker acoustics expire, effective February 1, 2013. All current orders will be built as agreed.
Build Your Own Effect Pedal. Mammoth Electronics makes an effort to offer our customers a very neatly packaged and personally customizable effect pedal kit. Each guitar pedal kit comes equipped with everything you need to build your own effect pedal as quickly and inexpensively as possible without sacrificing quality. These DIY guitar pedals kits are designed to make building your own effect pedal easy for everyone from the hobby builder to the manufacturer. All parts are labeled and packaged in the kit for easy identification. Enclosures are fully customizable to the user specification and specially wrapped in a protective foam for safe transit. We’ve provided a wide selection for any effect pedal kit needs you might have. From a simple boost pedals, and fuzz pedals, as well as overdrive, distortion, and compression kits. We also have a wide range of modulation kits, including delay, reverb, tremolo, and phaser effect pedal kits. If you need a quick fix or a more complex guitar pedal kit, Mammoth Electronics offers a variety of options making it effortless to build your own effect pedal with a sound quality that will make an impression. We work hard to build relationships with only the best brands for our customers. These strong relationships allow us to provide extremely competitive pricing on all of our DIY guitar pedals kits.. We’re confident you will save yourself money & time if you build your own effect pedal with Mammoth Electronics. Mammoth Electronics offers customized DIY guitar kits and effect pedal kits that allow you to experiment with, create and amplify your own taste of music, without compromising on the sound quality. With added protective layering, these kits are safe for transportation and transit. We’re passionate about helping our customers build the best effect pedal possible so please Check out our Facebook page where you can provide feedback, share tips or ask any questions you might have about your latest projects.
Got this beautiful guitar less than a month ago and played a couple of solo acoustic gigs. People were wowed by the way the sound of this guitar fills the space ( I played it through a Bose tower). Loved the feel of the fretboard. Though the body is a jumbo, it doesn't feel like a dreadnought. The guitar looks very attractive too and I had one person come over during a break just to admire the guitar. So now here's why I have given it 4 stars. The electronics were faulty on my guitar. The tuner switch didn't turn off automatically after I hit them to tune the guitar. The light stayed on till the batteries were drained out. This happened twice to me after which I decided to send it back. I also noticed a big hum building up during my second gig with the guitar - I
Also shown in ’60s Bizarre Guitars, but not in the Teisco book photo, is a ca. 1954 Hawaiian Teisco EG-R which was sort of shaped like a Gibson and which had the same pickup as the J-1, with more elaborate symmetrical metal rocket shapes on the sides, housing the volume and tone controls. A chrome dome sat in front of the pickup between it and the dot-inlaid fingerboard. The head was stubby and rectangular. This was very “Moderne” looking, very Buck Rodgers.
In terms of how the effects and amp models sound, we give the Zoom G3X a 7 out of 10. Most effects sound great and very convincing. All but the most discerning tone snobs would be able to distinguish them from the “real thing.” As is typical for digital multi-effects units, the quality of the overdrive and distortion effects is sub-par. Conversely, delays, reverbs, and choruses sound pretty great. In fact, one recommendation many users make is to start out with the Zoom G3X, and eventually buy a separate dedicated overdrive or distortion pedal, like a Fulltone OCD or Pro Co RAT2. This comment from an owner sums it up well:
Every amp will have a preamp and a power amp. These are often referred to as the preamp stage and power stage. The preamp picks up the signal from the guitar and boosts it so other parts of the preamp can manipulate it (this is where EQ and gain kick in). The power amp then takes that modified signal and boosts it to a level where the speakers can push it out. You will run into these terms most often with tube amps, as different tubes are installed in each of these stages.
Hawaii was key in the development of the electric guitar. There was a giant Hawaiian craze in the 1910s and 1920s, with a rise in popularity of the island’s sounds and culture (as often seen in movies and Broadway performances). Integral to Hawaiian music is the Hawaiian-style steel guitar, which most of early electric guitar development modeled itself after.
If you have ever played or listened to metal, you probably know about Ibanez. This brand has been around for a while and has become a patron saint of those who like harder sounding music. Built for speed, Ibanez guitars bring are finely tuned instruments which enable the player to explore the limits of their skill. On top of that, any Ibanez guitar is going to be great value for the money.

There were also four full-sized archtops; the Model EP-14, Model EP-15, Model EP-17 and Model EP-18. These were basically all variations on the same guitar, with glued-in necks, non-dipped heads, mini-strip plastic inlays, single rounded cutaway, f-holes, adjustable bridge, trapeze tail and translucent pickguard. Rocker switches were mounted on a small plate on the upper shoulder, while the volume, tone and jack were on a small plate on the lower treble bout. The EP-14 (shaded mahogany) and EP-15 (natural) had two pickups. The EP-17 (shaded mahogany) and EP-18 (natural) had three pickups, some two-tone, some flat rectangular metal-covered.
Lets face it: when most folks first pick up the electric guitar, the only other gear they think they might need would be an amp, a pick, some cables and maybe some pedals if they are savvy. As these players become more experienced and move from their garage to live music venues and recording situations, they eventually run into some issues and realize there must be better ways to be heard than turning the amp to 11.
Seagull guitars were first manufactured in Quebec in 1982. Their goal was to introduce a high-quality guitar with all the essentials for a reasonable price. It goes without saying that they completed that goal, as Seagull guitars are still here today.Seagulls are great for both beginners and pros. They are durable and high-quality. They have incredible sound-quality and they have something for everyone. They make both acoustic and electric guitars at reasonable prices. Seagulls are easy to play even for beginners. Additionally, they strive to reduce the impact guitar manufacturers have on the environment. They use sustainable wood sourcing so that they can avoid deforestation. Reclaimed wood is often used in the production of Seagull guitars. 
Like trapeze tailpieces, top mounted vibrato bridges transfer the string tension to a guitar’s side, offering more natural string resonance. Embedded units like the Vibrolas found on Gibson Flying Vs transmit the tension to the guitar’s body. Through-body units do neither, employing strings to absorb the string tension. Another system, the TransTrem, developed by Steinberger in the ’80s, has locking positions that allows players to transpose their tuning to other keys.
For a long time Yamaha were regarded as one of the best producers of student guitars but their reputation didn't go far beyond that. And it's true that they make excellent guitars for beginners, I am one of the many who originally learned to play on their student nylon string C40. BTW I'm one of those guitarists who thoroughly recommend initially learning to play on a nylon string guitar.
We specialize in the repair and restoration of stringed instruments and Guitar repair in Nashville, and the surrounding area. Our services provide for stringed instrument repair and maintenance  of all makes and models.  We also sell stringed instrument related accessories. Contact us for all of your repair and restoration needs. We love rescuing injured instruments, and helping them make music again.
The first Merson guitar advertised in The Music Trades appeared in the December, 1948, issue. This was the Tempo Electric Spanish Guitar which listed at $59.50 plus $11.50 for a Dura-bilt case. The Merson Tempo was an auditorium-sized archtop with a glued-in neck, a harrow center-peaked head which looks almost Kay. The guitar was finished in a shaded mahogany with a pair of widely separated white lines around the edges. Available source material is hard to see, but these appear not to have any soundholes. The fingerboard was probably rosewood with four dots (beginning at the fifth fret). This had a typical moveable/adjustable compensated bridge, elevated pickguard and cheap trapeze tailpiece. One Super-Sensitive pickup sat nestled under the fingerboard, and volume and tone controls were “built-in.”
Here we JUST SOLD OUT: another excellent FG160 for your serious consideration the Yamaha FG 160 Acoustic Guitar Made in the early - mid 70's from Taiwan factory. This example was built well over 35 years ago and was built to very high detailed standards as well as some of the best grained Mahogany woods seen in this time period ( see pics for those detail ) in that time period these were meant to compete with the great M@r#!n and now this Yamaha is quite well aged too and is a REAL vintage guitar in its own right sounding SWEET with its well aged woods with really beautiful patina of a true vintage instrument. This one has the Amber/Tan label and not the Red Label but the golden label. The frets are very good - original I did a quick dressing of the lower 5 or so frets and polished all. The guitar has it's natural age and character with beautiful patina and it has been played of course its not new its over 35 years old with a few insignificant minor nicks,dings from a well loved and adult respected instrument. This fine example is here and in stock... We upon receiving have remove the strings cleaned and detailed the guitar oil rosewood and polish finish, We have * upgraged* its TONE by installing a Martin BONE nut and compensated BONE saddle set for improved tone resonance over the old plastic stuff so she has a nice deep ring to its tone now and this guitar to plays very well Yamaha's and they are truly amazing instruments very well compared to a much more expensive brand guitar as you may have heard…. These FG’s are known for there fine construction and playability with amazing tone for this kind of money… to get a vintage aged tone woods instrument built this well and in this kind of condition make this FG160 the one to own for a song! Re: condition its over 35 years old and is BETTER than average This guitar has no cracks, no finish checking no warped top, no loose or pulling bridge Its neck has a real nice feel to it and is a medium - slim profile = feels like M@r#!n D-28ish substantial but not too fat - Just right! 1-11/16ths at the BONE NUT Play action is very good see pics Its a standard Dreadnought Acoustic and is Identical to the Yamaha FG180 This is an excellent vintage Yamaha FG160 You will be pleased with its sound she has good bones its over 35 years old and has proudly stood the test of time there is no reason this guitar will not continue to serve another 35+ years with average care. Beautiful Patina only seen on real vintage guitars Let me know if you have any questions ore are ready to purchase email Joe at JVGuitars@gmail.com.
A wah-wah pedal is a moving bandpass filter whose frequency center is controlled by the musician via a rocker pedal. This filter boosts the frequencies in the instrument signal around the moving frequency center, allowing the musician to emphasize different areas of the frequency spectrum while playing. Rocked to the bass end of the spectrum, a wah-wah pedal makes a guitar signal sound hollow, without upper harmonics. On the other end of the sweep, the filter emphasizes higher-end harmonics and omits some of the low-end "growl" of the natural instrument sound. Rocking the pedal while holding a note creates a sound that goes from growl to shriek, and sounds like a crying baby, which is how the effect got its name and also the reason behind the Crybaby line of wah-wah pedals. The wah-wah pedal, used with guitar, is most associated with 1960s psychedelic rock and 1970s funk. During this period wah-wah pedals often incorporated a fuzzbox to process the sound before the wah-wah circuit, the combination producing a dramatic effect known as fuzz-wah.
Many guitars (even new guitars) need the frets leveled in order to play buzz-free with low action. Most electric guitars with bolt-on necks come from the factory with high tongue frets. Doing great fret work is a learned art, and I guarantee that you will be happy with mine. All my fret work jobs are performed with the guitar mounted in a neck jig that simulates string tension. This allows very accurate work. Re-fret jobs include leveling the fretboard if needed.
As to the “where,” positioning your mic an inch or less from the grillecloth and aiming it straight at the center of the speaker cone – pointing at the dust cap, in other words – yields a bright, punchy, detailed sound that suits many requirements, but can be too harsh. At the other extreme, aiming the mic at the edge of the cone, where the cone meets the suspension (the area just inside the speaker cutout in the cab’s mounting baffle) usually results in a looser, warmer, more raw and edgy tone. Between these two positions, there’s a wealth of voices to explore, and every inch of real estate that the mic covers between dust cap and cone edge will bring a noticeable sonic shift, without touching the amp’s controls. Also, aiming the mic straight at the speaker, in other words, mounted at 90 degrees to the flat plane of the front of the amp, and aiming it off axis, at a slight angle to the speaker, will illicit different sounds, too. With an assistant helping, or the guitarist playing if that’s not you, try moving the mic around the surface of the speaker while listening for the changes in tone through monitors or headphones, or if you don’t have enough isolation between live amp and monitors, record a little in each of several positions to listen back to. Pick the position you like for the track, and go with it.
Amazing unit! I loved using my POD XT Live for years and wanted to upgrade. This unit totally exceeded my expectations. Sounds amazing and it's incredibly flexible for routing processing and effects chains. They built the hardware better and it's got a better set of pedal buttons too. Absolutely recommend! (Plus, they announced at NAMM that there will be more model packs, so that's great too!)
I have been playing guitar for over 40 years and purchased Taylor's, Gibsons and Fenders as well as many others. This Godin company understands value and passes that along to its customers. Fine tone when played acoustic or threw an amp. The wood tone and workmanship are awesome for this or any price point. You will not be disappointed with this guitar, it is a great value.
The Effect:To this day, there are 3 main delay pedal types coexist, Tape is usually the most expensive and sough-after (especially Vintage releases) type as they provide very natural sound reproduction. Analog were modernized in the 70’s and they worked on electronics, with a minor drawback according to some as they store up to 3 seconds of Delay time. Digital pedals is the type met with most frequency on today’s market, offering longer-than-usual Delay times and pristine sound reproduction, these are usually your best pick. A lot of players know that they want a delay effect but have no idea from where to start, if you are one of them, try the Boss DD-7 Digital Delay Pedal The most basic and often met controls on Delay pedals are Time, Level and Feedback, you’ll sometimes find them labeled differently but with the same function and purpose.
Other high-quality specifications include a bone nut, a molded metal jack plate that is curved and makes plugging and unplugging a guitar cable hassle-free, retooled knobs, fretwire that is slightly smaller than what you’d find on most PRS electric guitars, and PRS’s double action truss rod (accessible from the front of the headstock for ease of use).

Thank you Ola and David for this excellent article. The approach is totally scientific: you try to study the impact of one element of a system while keeping the rest of the settings identical (same pickups, same strings, same picking, etc.). The wood used modifies effectively the electrical spectrum composition and therefore the sound we hear. All the difficulty is that the wood is a part of a very complex system (woods combination, building type, pickups, strings, effects, amplification, restitution, etc.) and, without a solid knowledge or skills, it could be difficult to choose the right elements of the system to get what you want…
What people may not know is that they have a very affordable line of entry-level guitars.  This line continues the legacy of craftsmanship and prestige that comes with owning a Taylor. Whether you look into their line of Baby Taylors – 3/4 sized guitars that play better than many full-sized budget guitars, or you look into their entry full-sized acoustics, Taylor will not disappoint you.
Consider so-called “vintage” or “’50s-style” wiring, in which the tone pot and cap are connected to the middle lug of the volume pot rather than the usual third lug. Given the sheer number of posts the topic has amassed on guitar-geek sites, you’d think it was an earth-shaking option. Yeah, it’s a cool mod that I happen to dig, but really, the sonic benefit is modest: just a bit less loss of brightness when you dial down the volume.

He assumed the stage name Muddy Waters and released a series of historic recordings on the legendary Chess Records label. These discs established the quintessential Muddy Waters persona—the jive-talkin’, sharp-dressed, tough-as-nails, mojo-workin’ Hoochie Coochie Man. Waters’ confident, cocky vocal delivery was augmented by the knife-edge drama of his bottleneck guitar leads. This steely, highly electrified sound galvanized a new rising generation of British rock musicians when Muddy first visited those shores in 1958.
Several concert sound subwoofer manufacturers suggest that their subs can be used for bass instrument amplification. Meyer Sound suggests that its 650-R2 Concert Series Subwoofer, a 14-square-foot (1.3 m2) enclosure with two 18-inch drivers, can be used for bass instrument amplification.[23] While performers who use concert sound subwoofers for onstage monitoring may like the powerful sub-bass sound that they get onstage, sound engineers may find the use of large subwoofers (e.g., two 18" drivers) for onstage instrument monitoring to be problematic, because it may interfere with the "Front of House" sub-bass sound.
Many guitarists with instruments that have more than one pickup spend most of their time on the bridge unit. Using a variety of pickup positions when recording will thin or fatten the sound as required, but also help free up space when it comes to the mixing stage. Think of a recorded mix as a layer cake; too much density in one frequency range will cause a headache for the mixing engineer.

Overstock SaleNew ProductsVacuum TubesSpeakersAccessoriesAmplifier PartsBooks & DVDsCapacitor Amplifier SetsCapacitorsCoversEffect Pedals & PartsEnclosuresFootswitch BoxesGift CertificateGrill Cloth, Tolex & PipingGuitar PartsHardwareJacks & PlugsKeyboard PartsKitsKnobsLuthier ToolsMaintenance ProductsPMT Tone ModsPotentiometersPower AccessoriesRadio & Antique Equipment PartsResistorsReverb TanksSemiconductorsSpeakersSwitchesT-shirts/GiftsTech SuppliesTerminal Boards & StripsTransformers & ChokesVacuum Tube AccessoriesVacuum Tube Amplifier SetsVacuum TubesYellow JacketsZero Glide Nuts

One of the best and most affordable gigging amps I have ever played. Blackstar accommodates all styles and budgets and should be in place of line 6. Too many people want traditional tone, but Blackstar brings a new edge to the table and builds extremely reliable tough as nails amps with new ideas like the ID series amps, I own an ht40 and am extremely impressed. Get one.
Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Maple - Neck Wood: Maple - Neck Construction: 3 Piece - Fingerboard: Ebony - Frets: 22 - Inlay: Block - # of Strings: 6 - Headstock: 3+3 - Bridge: Bigsby - Cutaway: Single - Hardware: Chrome, 3x Volume Control, 1x Tone Control, 3-Way Switch - Guitar Features: Pickguard
Another factor to consider are the alloys used to make the string. Acoustic strings may be phosphor bronze or an 80/20 bronze/zinc alloy, electric strings may be pure steel or a steel/nickel alloy, and the outer winding on the thicker strings may be either round wound or flat wound, which is typically used by jazz guitarists for smooth fingering with less fretting noise. Acoustic and electric strings are both now available with special super-thin coatings to protect them from sweat and corrosion. Coated strings cost more, but generally last much longer. Find out what type of string your favorite player uses, try guitars with different types of strings at your local guitar store, then try a few different sets on your guitar to see what feels and sounds best for your playing style. Major manufacturers include Ernie Ball, Martin, GHS, D'Addario, and Elixir, among others. Make sure you have a string winder to make installing the strings go faster, and some pliers with a fine wire cutter to clip the excess string from the tuning post, a well as some guitar polish - changing strings is a good time to perform some routine maintenance. Keep a clean cloth in your case to wipe down the strings after each use, along with extra bridge pins for your acoustic guitar. Regular string changes are the best way to keep your tone crisp and clear, so grab a pack and tune 'em up!
Conceived in the early 1930s, the electric guitar became a necessity as jazz musicians sought to amplify their sound to be heard over loud big bands. When guitarists in big bands only had acoustic guitars, all they could do was play chords; they could not play solos because the acoustic guitar is not a loud instrument. Once guitarists switched from acoustic guitar to semi-acoustic guitar and began using guitar amplifiers, it made the guitar much easier to hear, which enabled guitarists to play guitar solos. Jazz guitar had an important influence on jazz in the beginning of the twentieth century. Although the earliest guitars used in jazz were acoustic and acoustic guitars are still sometimes used in jazz, most jazz guitarists since the 1940s have performed on an electrically amplified guitar or electric guitar.
Its very obvious very few on this list have never picked up a guitar in their life as this looks like a what brand does my favorite band play list... Considering Gibson these days are garbage and only were good for a few style to begin with no way they're number one... Fender has very solid build quality, but to diversify them to play numerous styles takes heavy modification. As far as electric are concerned there is a number that can top the list, as schecter, esp and Jackson are too low on the list and I've heard good things about rickenbacker. Ibanez is also excellent. Its really a toss up for me...I haven't played much esp do I phased them out...I have extensive time with Ibanez schecter and Jackson... Ibanez is gone because the build quality is no better and the playability is pretty much the same as a Jackson but the Jackson gives you far more bang for the buck... As for schecter and Jackson they put out some fully loaded guitars that are only going to rock you maybe a weeks ...more
Another aspect of the jazz guitar style is the use of stylistically appropriate ornaments, such as grace notes, slides, and muted notes. Each subgenre or era of jazz has different ornaments that are part of the style of that subgenre or era. Jazz guitarists usually learn the appropriate ornamenting styles by listening to prominent recordings from a given style or jazz era. Some jazz guitarists also borrow ornamentation techniques from other jazz instruments, such as Wes Montgomery's borrowing of playing melodies in parallel octaves, which is a jazz piano technique. Jazz guitarists also have to learn how to add in passing tones, use "guide tones" and chord tones from the chord progression to structure their improvisations.
Recently picked myself up a second J28SCDL Jumbo, which was set up beautifully and I have to say it truly is an amazing guitar. It could give some of the higher priced guitars a run for its money. Lovely sound, creative design and clearly a lot of guitar for your money. I seriously encourage you not to over look Washburn when looking for a good guitar at an affordable price. Might end up your favorite guitar!
12 Month Financing: For a limited time, purchase $599 or more using the Amazon.com Store Card and pay no interest for 12 months on your entire order if paid in full in 12 months. Interest will be charged to your account from the purchase date if the promotional balance is not paid in full within 12 months. Minimum monthly payments required. Subject to credit approval. Apply now.
Open Loop Gain: Feedback Solid-state amplifiers are inherently nonlinear. They have a very large ‘open loop gain’ approx 20,000. The amplifier output is (feedback) to the comparator input to reduce the gain to approx 50. Therefore 99.9% of this feedback corrects all instability and non-non-linearity of the amplifier, as explained in amplifiers. The speaker also acts as a large microphone. All non-linear movements and vibrations within the speaker cone, (caused by reflected nodes, chaotic resonances etc) of which there are many, are regenerated back into electricity by the voice coil. This re-generated signal from the voice coil is inadvertanetly fed-back to the solid-state amps comparator input, and re-amplified back to the speaker as recycled distortion.
Repetitive open-tunings are used for two non-Spanish classical-guitars. For the English guitar the open chord is C major (C-E-G-C-E-G);[67] for the Russian guitar which has seven strings, G major (G-B-D-G-B-D-G).[68] Mixing a perfect fourth and a minor third along with a major third, these tunings are on-average major-thirds regular-tunings. While on-average major-thirds tunings are conventional open tunings, properly major-thirds tunings are unconventional open-tunings, because they have augmented triads as their open chords.[69]
I participated in what I think was perhaps Gibson's best SG...a prototype made for Robbie Krieger. It had my then-patented carbon fiber "T" cross section fingerboard which absolutely took care of the #1 problem with SGs...the rubber neck syndrome. It also had a beautiful flame maple top on the mahogany body and it got a cherry sunburst. Fabulous guitar. Robbie must still have it.
16-Series: Style 16 guitars were first introduced in 1961. Later, they were the first production Martins to utilize sustainable, native woods such as ash and walnut, as well as the first to implement hybrid A-frame “X” bracing. Today, these models use solid woods such as mahogany, East Indian rosewood, koa, sapele and maple. Models include DC-16RE Aura, OMC-16E Koa, D-16 GT, 000C-16RGTE Aura and the J12-16GT, a 12-string jumbo-size guitar with the series 16 appointments. Most -16 series instruments use the Martin long scale, 25.4″.
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Maple - Quilted - Neck Attachment: Neck-through - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Frets: 24 - Inlay: Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black, Diecast, Nickel, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Black, Blue
I’m also going to go out on a limb and suggest the earliest Univoxes also included the ‘Lectra, a version of the one-pickup Aria 1930 violin bass (made by Aria). These were basically violin-bodied basses originally inspired by the Gibson EB-0, and popularized among imports by Paul McCartney’s use of the Höfner violin bass, copied by EKO. This was a hollowbody with no f-holes, Cremona brown finish, single neck pickup, bolt-on neck with position dots along the top of the 22-fret bound rosewood fingerboard. Strings anchored to a covered bridge/tailpiece assembly.
The least expensive practice amps and basic combo amps may only have a single indicator light: an LED to indicate when the amp's power is on. More expensive amps may also have LEDs to indicate when the preamp has a signal present from the instrument (helpful for troubleshooting during set-up, because if the amp is not producing any bass sound even when the bassist is playing, and the "signal present" light is illuminated, this indicates that a signal is reaching the amp); when a limiter or similar speaker protection feature is activated (e.g., Peavey's DDT system); when clipping is occurring; or when the amp is in standby mode. Amps with a built-in tuner typically have several LEDs to indicate when the note being played is flat, sharp, or in tune.
 The world-wide reputation of the company is not based on design data and performance alone. The real key to success of SWING is "Outstanding People". Every staff member at Swing has a background as a professional musician. Moreover, we were all career veterans in guitar engineering with decades of combined experience, well before founding our new vision; Swing Guitar Technology. If you are familiar with musical instruments companies or have seen their ads or brochures, you may notice their catch phrase like "It's about Music." Nothing could be closer to the truth, based on Swing's pedigree. From the selection of materials to their treatment and hand fitting. From mechanics to electronics. Each stage of each final product is mastered by SWINGers.
The #1 cause of fret wear is the fretting hand pressure exerted by the player.  I have some clients that grip very tightly and wear frets quickly (Rob Fahey), and some that grip very lightly and take forever to exhibit significant wear (Jasan Stepp, Dog Fashion Disco/PolkaDot Cadaver).  Fret material hardness, string hardness and frequency of use all contribute to wear as well, but hand pressure is still the leading cause since frets do not wear themselves out.  Technique is different for every player, unique and personal and habits can be hard to change.  Just like brakes in a car, how hard and how much something is driven directly impacts wear and longevity.  Please see the refrets page for further thoughts on this topic.
What is the best acoustic guitar brand? That's subjective, and often based on a consumer's past experiences with a specific brand. This list includes a vast majority of the most recognizable good acoustic guitar brand names that are currently on the market. This list includes those acoustic guitar brands that consumers might wish to learn more about.
{"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: agile","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"martin","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
Many experiments at electrically amplifying the vibrations of a string instrument were made dating back to the early part of the 20th century. Patents from the 1910s show telephone transmitters were adapted and placed inside violins and banjos to amplify the sound. Hobbyists in the 1920s used carbon button microphones attached to the bridge; however, these detected vibration from the bridge on top of the instrument, resulting in a weak signal.[2] With numerous people experimenting with electrical instruments in the 1920s and early 1930s, there are many claimants to have been the first to invent an electric guitar.
×