In short, absolutely everything about this guitar screams quality. You can inspect the entire thing in tiny detail, and it’ll leave you amazed at how well it’s been made. And then when the sound hits you, you really feel it too. It’s perfect for chugging, powerful rhythm behind the rest of the band, but is equally adept at more sparkling highs and brighter choruses. What a guitar.
Which brings us to this 1985 DT-250. While it sports the tail notch, the shape is a little more sleek and diminutive than the comparable Dean ML. The lower front bout is extended to be almost symmetrical with the diagonally opposite bass wing. The treble-side lower bout is shortened, giving the whole guitar a tasteful offset-X shape… X Series. To add dimension to the shape, Fuji Gen Gakki added “crystal cuts” to the edges, basically code for angled bevels.

A humbucker pickup is electrically equivalent to two single-coil pickups wired together in series. Coil splitting involves shorting one of the coils to ground, essentially turning the humbucker into a single-coil pickup (not a perfect replica, though, as the magnetic circuits of the two pickup types are different). This is usually done with a DPDT switch, but can also be done with a push-pull pot. Some manufacturers have used a pot to vary the amount of signal shorted to ground from one coil, thus producing a range of tones between a humbucker and a single-coil. Coil splitting results in a sound that's brighter and has less output than a full humbucker. It also eliminates the humbucker's noise-cancelling properties. This modification requires the start and end of both coils to be exposed, which is more commonly available on aftermarket than stock pickups.[17][18]


PRS SE Standard 24 Electric Guitar The PRS SE Standard 24 is a great first or backup electric guitar. This is a reliable workhorse that more than delivers in design, build, playing comfort and overall sonic performance. It can also be your only electric guitar, but chances are you’ll want another one along the way and give in to another model - or another SE Standard 24.


Editorial comment – I advise folks when considering fretwork to consider not choosing a size or leveling operation resulting in less than .040” height if they want to play a style with frequent fret hand slurring, i.e. rock, blues, shred etc.  Low fret height is less capable of sustaining a reasonable fret leveling in the future, making it that much closer to refret time.  You don’t have to choose a very tall size if that is uncomfortable for you, but only choose a low height if that is really what you want and are accustomed to.
Thought you'd like to know. Before Christmas, I stopped by a local music shop to buy my 12 year old granddaughter a new guitar to replace an old Beaver Creek she'd been banging on for a few years. Since I'm an old folky from the 1960s, I thought a low end Gibson or Martin would give her both good sound and some bragging rights at her school's guitar club. The shop owner was in the acoustic guitar room strumming something I had never seen before and quickly told me I should forget Martin or Gibson and get what he was playing. It was a Seagull. An equal sound for half the price, he said, so I looked it over, strummed the few chords I could remember, and bought it on the spot. Later, I was still pondering how a little Canadian guitar could be called better than a Martin or Gibson when I found your ratings post. I do believe I kept repeating "Oh my God, it's true!" over and over. And she loves the guitar, especially the smaller neck and fuller sound. Thanks for helping this old folky who always thought Martin and Gibson were names to be spoken in hushed reverence believe in something new.
I went to my local guitar store, and tested every one on the wall (under $1,000). I narrowed it down to two (the Ovation acoustic-electric of the same caliber, and this Yamaha FGX800C). In the end I ordered this guitar because of the excellent price on the "package" deal (hard case, strap, tuner, etc.). It sounds fantastic, stays in tune very well, is comfortable to play, and no "buzz". My limit of 4 stars is due to; 1) The strap is garbage...get a new one if you play with a strap. 2) The guitar only has a strap post on the rear of the instrument (it also doubles as the connection for the amplifier cord), and there is none on the front. You have to tie a string ahead of the nut. That gets in the way of the tuning and fingering of
: : I own a Decca guitar, it is what I learned to play on many years ago. From what little I have gathered about them they were an order by mail brand, and you could only get them from a catolog such as Sears & Roebuck. I havent been able to find a price for them or any ifo on what catalogs they were from. Mine has a Ernie Ball Musicman-like peghead (4 one side 2 on the other) and has a metal pick guard with 2 giant switches which seem to have no effect on tone. It has a brown & yellow sunburst paint job (ewwww).I thought I possibly had the only one in existence, lol, guess not.
In the most commercially available and consumed pop and rock genres, electric guitars tend to dominate their acoustic cousins in both the recording studio and live venues, especially in the "harder" genres such as heavy metal and hard rock. However the acoustic guitar remains a popular choice in country, western and especially bluegrass music, and it is widely used in folk music. Even metal and hard rock guitarists play acoustic guitars for some ballads and for MTV unplugged acoustic performances.
Even working on the assumption that you're only using one mic, the professionals have an awful lot to say about where you might put it. For a start, it seems to be fairly common practice to audition the different speaker cones of your guitar amp. "They're supposed to sound the same," says Roy Thomas Baker, "but if you're using a 4x12 cabinet, each of these four speakers may sound different."
Bass effects that condition the sound, rather than changing its character are called "sound conditioners." Gain booster effects pedals and bass preamplifier pedals increase the gain (or volume) of the bass guitar signal. Bass preamplifiers for double basses are designed to match the impedance of piezoelectric pickups with the input impedance of bass amplifiers. Some double bass preamplifiers may also provide phantom power for powering condenser microphones and anti-feedback features such as a notch filter (see "Filter-based effects" section below).

Having a tuner on your pedal board is useful but these days I more often use a clip-on tuner, specifically the TC Electronic Polytune Clip (Buy at Amazon UK, Amazon US). I don't like the main signal to run through the tuner all the time if I can help it (I use the GigRig G2 switching system) but if you don't have that luxury, then look for a tuner with True Bypass like the TC Electronic Polytune 2 (Buy at Amazon UK, Amazon US) or use a Volume pedal that has a Tuner Output (many do these days!).
I wish I had a cool story to attach to this guitar, but really this one is a history lesson regarding the development of Japanese guitar manufacturing.  Plus, it’s an example of some rare component combinations (like the pickups) that make guitars like these worth buying.  THEY’RE SO CHEAP!!  Hell, buy one of these for $200, send it to Dano and sink another $100 into it, and you’ll have yourself one hell of a player!  It’s like recycling, dude.
I work out of my home shop in Idaho Falls, Idaho. I do repairs for clients and guitar shops all over the United States. I’d love to help you repair or restore your guitar. Repair prices are based on a rate of $60 per hour. These prices apply to guitars in otherwise good working order. Your repair may vary depending on the condition of your guitar and the specifics of the work needed. Please contact me using the contact page if you have a repair that you would like to discuss. Consultations are always free.
(48 Contiguous U.S. States) Free Free Shipping With Backstage Pass 92118 2-Day Standard Ground {savingIsUpTo=false, MSRP=1430.0, listPriceRange=false, isFreeShipping=true, download=false, isPriceDrop=false, salePriceRange=false, YourSaving=0.0, productId=site1prodL21430, MSRPRange=false, enablePDPColorOption=true, showBrandNameWithProduct=true, restockStartAmount=null, priceVisibility=1, listPrice=999.99, salePrice=999.99, isOnSale=false, showMSRP=true, restockCount=0}
Adding to their already good value, most multi-effects come with built-in features that are essential to gigging and practicing, first of which is a built-in tuner. Looping is also a good feature to look for, thankfully it now comes standard for most units. Having the ability to record straight to a computer is another handy features that should be considered, as well as the ability to edit the settings via your computer or mobile device. Built-in metronome/rhythm is also a nice plus, especially for those who want to take their skill to the next level.

Originally the Stratocaster was offered in a 2-color sunburst finish on a solid, deeply contoured ash body, a 21-fret one-piece maple neck with black dot inlays and Kluson tuning heads. In 1956 Fender began issuing solid Stratocasters with alder bodies.[4] In 1960 the available custom colors were standardized, many of which were automobile lacquer colors from DuPont available at an additional 5% cost. The unique single-ply, 8-screw hole white pickguard held all electronic components except the recessed jack plate—facilitating easy assembly. Despite many subsequent Stratocaster models (including copies and the Superstrat), vintage Fender models are highly valued by collectors for their investment potential and players who prefer the timbre of older models.
Steve is the best! He does great work and loves talking about all kinds of guitars. I brought my Squier Affinity Stratocaster to him for a setup and a pickup replacement job, and I learned more about Stratocasters from him than I ever would have expected. I will definitely be a repeat customer! From what I've seen, he treats all of his customers' guitars, from my Squier to an Eric Clapton signature Strat, with the same level of respect and quality of work.

Squier has now seen fit to introduce Fender's revered '72 Thinline to its own range, and it looks the business, with white pearloid scratchplate, finely carved f-hole and Fender- embossed humbuckers. While you'll find the gloss-finished modern C neck across much of Squier's Vintage Modified range, you're unlikely to find tones quite like the Thinline's anywhere else, certainly at this price. Cleans from the neck and middle positions are punchy and persuasive, not dissimilar to fat P-90-ish single coils, but flicking over to the bridge humbucker yields a burly, resonant voice that screams for big open chords and an overdriven valve amp. That's why it's one of the best electric guitars for Indie and alt-rock players.
Look for lyrics or chord changes. Many songs have guitar parts made up solely (or mostly) of chords. This is especially true for rhythm guitar parts. In this case, the tab may forgo typical tab notation in favor of a simplified list of chord changes. These chords are almost always written in standard chord notation (Amin = A minor, E7 = E dominant 7, etc.) Simply play the chords in the order that they're listed - if it's not noted otherwise, try playing one chord per measure, but if the changes don't sound right, listen to the song for the strumming pattern.
The Ultimate Beginners Series gets aspiring musicians started immediately with classic rock and blues riffs, chord patterns and more. Now, for the first time ever, Basics, Blues, and Rock are combined in one complete book and DVD set. Follow along with 4 hours of DVD instruction and 3 hours of audio tracks, with the help of on-screen graphics and printed diagrams. The Ultimate Beginners Series: Electric Guitar Complete takes you from picking to soloing and power chords. If you're serious about mastering the blues and rock styles, this book and DVD set is a must-have.
All of the complex air-coupling interactions, along with the resonant properties of the tonewoods themselves, are a key reason that different acoustic guitars will have different tonal qualities. The sound is a complex mixture of harmonics that give this type of guitar its distinctive sound. Some of the most important varieties are the classical guitar (nylon-stringed) and steel-string acoustic guitar.
Of course, the effect is not as good as using a professional studio but most users report that reproduction is very good for a simple computer application. The interface of Guitar Rig is extremely well laid out and even for those new to amps and guitar effects, it doesn't take long to navigate your way around. If you intend to use Guitar Rig for live performances, a convenient Live View displays the most essential readouts and level monitors to keep your eye on.
When technology changed from valve to solid-state, it was noticed that solid-state amplifiers lacked warmth and bass performance, and had to be twice as powerful as valve amplifiers, to sound as loud. Current Drive: Solid-state amplifiers behave in ‘Voltage Drive’. This acts as a short circuit (zero output impedance, or 100% damping factor) across the speakers, causing excessive damping, which reduces efficiency, limiting responsiveness. Valve amplifiers behave in ‘Current Drive’. This represents an open circuit across the speaker without over damping, allowing maximum response and efficiency.
This is an amazing 6 stringed electric guitar from Ibanez that is right handed and comes in a beautiful white color. The body is made from basswood  and kneck of rosewood. It is perfect for anyone to be his/her first guitar regardless of the music. Prices range from around INR 12,124  depending on the prevalent market factors such as whether there are offers or discounts available. You can find more details regarding this model by clicking on the link below:
Chicago’s vintage guitar shop is located in Ravenswood just west of Lincoln Square. Rock N Roll Vintage is your one stop shop in Chicago for new guitars, vintage guitars, Chicago guitar lessons, guitar pedals, and we are currently the largest synth dealer in the Midwest. Looking for a specific guitar? Rock N Roll Vintage Guitar Shop carries Fender, Gibson, Martin, Gretsch, Rickenbacker and other popular guitars and basses including boutique amps. We have one of the largest selections of effects pedals in Chicago with many hard to find boutique pedal brands.
it is four solders on a guitar on say a les paul needs electricty so two wires pass the electricity through the other two wires are for your pickups the pickups electricity goes through the wires of them , into a potentiometer which is the technical name for the thing under the knob (or two depending on the guitars wiring) .... than into the 3 way and than finally passes out of the guitar and into an amp , pedal or tuner
A bass equalizer is the most commonly used of these three effects. It adjusts the frequency response in a number of different frequency bands. While its function is similar to a tone controls on an amplifier, such as rudimentary "bass" and "treble" frequency knobs, it allows for more precise frequency changes. A rack-mounted bass equalizer, for example, may have ten sliders to control the frequency range encompassed by a regular "bass" frequency knob.
The Jameson Left-Handed Black is an acoustic-electric guitar that comes with a slick appearance, a smooth body, and an impressive sound. With its thinline frame and cutaway design, this model is good for both amateurs and seasoned guitar players. You get a guitar that sounds just as awesome regardless if you’re playing it unplugged or through an amp.

Much like any other job or hobby, building guitar pedals requires specific tools in order to get the job done. Furthermore, before you start putting together your first build, it is vital that you have a significant understanding of how to solder circuit board electronics – otherwise you may find yourself at a loss due to faulty soldering (believe me, this is not a fun issue to troubleshoot).  If you need to practice soldering, here is a helpful video.

The best way to use this type of book is to just take 15 minutes a day to work through a page or two at a time. You don’t have to find something that requires a lot of study or dedication on your part at this point. Your first priority should be finding a book that gets you thinking about theory as well as helping you develop coordination in both your fretting and strumming hand.


In music, a guitar chord is a set of notes played on a guitar. A chord's notes are often played simultaneously, but they can be played sequentially in an arpeggio. The implementation of guitar chords depends on the guitar tuning. Most guitars used in popular music have six strings with the "standard" tuning of the Spanish classical-guitar, namely E-A-D-G-B-E' (from the lowest pitched string to the highest); in standard tuning, the intervals present among adjacent strings are perfect fourths except for the major third (G,B). Standard tuning requires four chord-shapes for the major triads.
Salas is also bullish about the guitar’s prospects. “My 10-year-old son is at school in Austin, Texas and him and his friends are rocking out to 1970s funk,” he said. “A new generation is getting into guitar and rock’n’roll. I believe there’s going to be a massive comeback and that means with that style of music the electric guitar is going to make a comeback.”
In addition to pickup selection, most guitars will have controls for volume and tone. Volume controls simply regulate the strength of the output signal. Depending on the amplifier, this can control the tone as well as the volume. Most tone knobs control high frequencies and many guitars have separate tone controls for each pickup. This can vary a guitar’s sound between soft, warm, and mellow to a very bright, raw, distorted sound.

Replacing or repairing knobs. Knobs are covers for your pots so you can easily turn them, if any of your knobs are unable to be correctly placed on try due to broken or enlarge holes, place a good amount of tape around the pot's shaft that covers it and try to keep the the knob on the tape. If you cannot do so then you may need to replace your knobs.


The hollow body — the original electric guitar design — is completely hollow on the inside, like an acoustic guitar. Hollow-bodied guitars like the Gibson ES-150 saw use in jazz ensembles by players such as Eddie Durham and Charlie Christian, but were also adopted for country, folk and, eventually, rock and roll. If you’re looking for warm, mellow tones, the hollow body is your best bet. That isn’t to say it can’t give you some sweet, raunchy distortion. A proper hollow-body setup can pull off a great classic blues or rock sound, but they are more prone to feedback than solid body guitars.
The demand for amplified guitars began during the big band era; as orchestras increased in size, guitar players soon realized the necessity in guitar amplification & electrification.[14] The first electric guitars used in jazz were hollow archtop acoustic guitar bodies with electromagnetic transducers. Early electric guitar manufacturers include Rickenbacker in 1932; Dobro in 1933; National, AudioVox and Volu-tone in 1934; Vega, Epiphone (Electrophone and Electar), and Gibson in 1935 and many others by 1936.

Flanger pedals are based on a studio sound made when two tapes were mixed together and one was delayed. What this does is add shifting harmonic content to your signal, as well as modulation. Flanging is a very distinct effect that adds a unique whoosh or airplane-like sound. Used with restraint, the flanger adds an interesting dimension to your sound, almost synthesizer-like sound. Used at extreme settings, flangers will over take the tone and bring a solo to completely different sonic level.
Love love love this guitar! I ordered it because it reminds me of my Dad's old Kay archtop that I initially learned to play on. The retro jazz style of this guitar is awesome. My musician friends love it and and like the sound of it although they haven't heard it plugged in yet. It took me a very short while to get used to the strings (made by the company for this guitar) and while they have a tinnier sound than what I'm used to for an acoustic guitar, they do deliver when it is plugged in. Overall it really seems to be more of an electric-style guitar. The neck is narrow and the body is small - something that I am so happy with! It is extremely playable. I may switch to bronze strings to get a warmer tone, but for now I want to give these strings a chance to sing. I also ordered a case from the company that fits this guitar, and for the price, it is awesome as well! Very light and the guitar fits perfectly and securely. At a recent gig, a complete stranger came up to me to look at and admire this guitar - it truly is a beautiful instrument. The woodgrain is rich and not as red as the pictures make it look. I feel like Stu Sutcliff - don't really need to know how to play - I can simply stand in the background and look cool ;-)
Relatively new to the amplifier world, Paul Reed Smith is building some of the most interest amps out there. After tapping legendary amp builder Doug Sewell to head design, the company has produced a range of boutique-quality amps for a fraction of the price. The Sonzera 20 is a reliable amp that is incredibly versatile, with a full tube sound similar to American amps from the ’60s.
For die-hard metal players looking for best electric guitar brands, Dean is another famous name you wish to check. The iconic ML design has become a signature instrument for rock because of Damageplan and Darrel Abbott of Pantera (late). In the ’90s, ML was revived by Dime, and then Dean stretched out the idea while sharpening the designs of it with a modern touch.

The guitar builder for the giants of jazz, Ibanez now introduces the Artstar AS153 Semi-Hollow Electric Guitar, to answer the needs of the working professional player. Crafted from specially selected tone woods, this guitar features a bone nut, ebony fingerboard, hand-rolled frets and Ibanez's famous Super 58 pickups-capable of tone magic any place...  Click To Read More About This Product

You’ve decided to pick up an axe and learn to shred like one of the pros. While mastering the guitar is no easy feat itself, before you even start jamming you’ll probably find yourself looking through site after site trying to find the right instrument. It’s hard. There’s an expansive list of components to be taken into account: body styles, wood types, pickups, bridges, necks — and that’s just scratching at the surface.

The 700-series guitars had all controls and pickups mounted on a faux-tortise shell pickguard. That makes it very easy to do any required work on the electronics. By contrast, On the 800-series, with a couple of exceptions, the tone and volume control pots and the jack socket are mounted to the body, a three-way pickup switch, and a lead/rhythm slide switch are mounted to the pickguard; and the pickups are mounted to individual little mounting plates made of the faux-tortise shell material.

Buddy Holly was one of the pioneers of the Stratocaster and used the instrument on virtually all of his songs with the Crickets. During the recording of “Peggy Sue”, rhythm guitarist Niki Sullivan was not needed for the song, and instead stood next to Holly, and flipped the selector switch of Holly’s guitar from the neck pickup to the bridge pickup for the guitar solo.

One unique application of a fuzz pedal involves starving the pedal of voltage--which will produce a scratchy, velcro-like tone. This is desirable by some musicians because it is a highly unique sound and is often employed by more avant garde musicians. This sound can be achieved by purchasing a power supply with a sag output, or using a nearly dead battery, although the pedal won't last long when using that method.
Telecaster is the original solid body guitar. Ever since this iconic model has only grown in popularity. This Tele we look it at here is a bit different. It comes packing an H/S/S pickup configuration, which you don’t see that often on these guitars. With that said, it feels and sounds awesome. I had it setup with a vintage Marshall Plexi and the sound was just impressive. There’s definitely more tonal range than you get in a standard Telecaster.
One glance at an El Dorado strap and you'll understand why so many musicians choose leather as their go-to pick for stage, studio or practice play. By combining sleek designer style with rugged, durable materials, these straps offer everything you need in a reliable accessory. And when you can keep your guitar secure while rocking out onstage, you'll be free to concentrate on the more important matter of dazzling your fans.
All this is to say that you don't need to worry about getting your hands on a large amp. Small amps perform better for the overall sound of your band in most venues, and any venue big enough for you to need more volume is going to mic your amp anyway, giving you all the juice you'd need. So, as you look at the amps on our list, you can evaluate them based on their EQ options, their effects, and, frankly, their look.

music is an expression with a variety of feelings involved.there is no such individual as the greatest guitarist.there are however a great number of highly talented,highly skilled and original guitar players.they encompass many genres of style ,technique,they should not be compared with each other.rather they should be appreciated for their individuality and that magnetism that makes them all unique.

{"eVar4":"shop: amplifiers and effects","pageName":"[gc] shop: amplifiers and effects","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: amplifiers and effects","prop1":"[gc] shop: amplifiers and effects","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"amplifiers & effects","prop5":"[gc] shop: amplifiers and effects","prop6":"[gc] shop: amplifiers and effects","prop3":"[gc] shop: amplifiers and effects","prop4":"[gc] shop: amplifiers and effects","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
I have never had a negative experience here. The staff is genuinely pumped about guitars. Every time I have gone in, I have always been greeted in a friendly manner and I have never felt that I had asked a stupid question. I really appreciate that they are able to take some of the intimidation out of purchasing a new guitar and put no pressure at all to buy. I'm so glad this store exists here in Seattle! Thank you so much guys!
The Effect: Bass guitars are the core of every band. Along with drums, they make the rhythm section. Because of this, bass players are seen as ‘background members’ in a band. With that said, bass guitar offers much more range than that. Following the footsteps of legends such as Lemmy Kilmister and others, we can see that bass guitar can be the star of the show. All you really need is a good distortion pedal. Finding one may prove to be trickier than it seems. Your average guitar dist pedal may work, but chances are you will get better results with something like Tech 21 RIP Red Ripper. This is adedicated dist box for bass guitar, which covers the low end segment of bass tone and gives you some advanced tone shaping options. A proper bass dist box can really make all the difference if you are looking for proper sound.
went to great lengths to get here for a basic set up on a vintage les paul. after 3 months of long waiting guitar was no better off, it was different, but just as bad and completely unplayable. he may have spent 30 seconds tweaking the truss rod, but didn't do the necessary or requested fret leveling to resolve all the dead areas up high. unbelievable after 3 months to have a guitar unplayable after traveling such lengths to get here & back. when FINALLY picking up he was running down the stairs leaving early, i barely caught him so didn't get a chance to play it before taking it home, or would have had a chance to address this disappointment. there were dead frets all over the high strings. he clearly didn't perform the service that i paid for. a year later that vintage les paul is still in the same unplayable condition and needs a full service by a real luthier. i am writing this now because i can't even look at this guitar without thinking about this experience, and still can't enjoy playing this very expensive and special vintage piece. i went to great lengths to get all the way to this shop, it was extremely difficult, several trains, a really long walk. then i waited a truly insane 3 months, and then went to the same lengths to pick it back up. he did say to me to bring it back, but that was impossible. never in my life, in NY or LA, or anywhere in between have had to wait more than 1-2 days for any service on any guitar. in my experience he takes on way more work than he can handle and apparently doens't do a thorough job. 3 months is obscene. 1 month is unacceptable. bad experience, 100% waste of time & money. if he refunded my money it would not come close to the amount of time i had invested in getting here & back. truly negative experience. waste of much time.
The Fender Mustang I V2 Guitar Amplifier Combo also features USB connectivity allowing you to hook it up to your computer or DAW software for easy recording. If you don’t already have a DAW, you can utilise the free downloads of Fender FUSE and Ableton Live software suites to create your own music and take advantage of all the great features within the amplifier when recording. An intuitive, easy to use control panel allows you to see and change your sounds and footswitch connectivity (sold separately) ensures you can have complete control without the need for a pedalboard. A fantastic amplifier for beginners and players of all levels.
OK, I’ve put a new set of strings on now. We’re now going to carry out the following steps, just like we did in the general electric guitar setup post. 1. Check and adjust neck bow (how straight the neck is) 2. Check and adjust saddle height 3. Check and adjust the intonation (how far back or forward the saddles need to sit at the bridge to keep your guitar as in tune as possible no matter what fret you’re playing)
Neither should you confuse acoustic-electric guitars with semi-acoustic hollow or semi-hollow instruments. Acoustic-electrics are acoustic guitars with onboard electronics that allows them to be amplified. They can be played just as well without plugging in. Semi-acoustics are electric guitars with some acoustic properties that are meant to be amplified when played.
Some of the earliest electric guitars adapted hollow bodied acoustic instruments and used tungsten pickups. This type of guitar was manufactured beginning in 1931 by Electro String Instrument Corporation under the direction of Adolph Rickenbacher and George Beauchamp. Their first design was built by Harry Watson, a craftsman who worked for Electro String. This new guitar which the company called "Rickenbackers" was the first of its kind.
When two sine waves with frequencies A and B are ring-modulated, the output will also contain the frequencies A+B and B-A. If frequency B is not a multiple of A, these additional frequencies are inharmonic; e.g. ring-modulating sine waves at 1000Hz and 1250Hz will add the frequency 2250Hz, which is neither a multiple of 1000Hz, nor of 1250Hz. When more complex sounds are ring-modulated, sums and differences of all the harmonic frequencies are added.
Most guitars will have at least one TONE knob - a way to adjust the frequency spread of the signal going to the amplification system. Similar to a TONE adjustment on radios, stereos, other things; it usually is a means to adjust how much of the higher frequencies are sent to the output. Rolling the knob “back” will reduce the higher frequencies and can help make the guitar sound less “shrill” if it exhibits that tendency.
Next was Eunice's ‘electric guitar’. It was beautiful and hardly used. However a common problem with guitars of this era were the horrible pickguards made from celluloid that would off-gas while in storage and then wreak havoc over the guitar’s other parts. Upon closer inspection the guitar was actually dripping wet from the many years of storage in the hard case.
The Marshall CODE412 - 4x12 Speaker Cabinet is a powerful monster designed as a companion to your CODE 100 head. A classic angled cabinet that is packed with four 12” speakers, each with a 30-watt output. This extremely affordable 4x12 amplifier cab is perfect for those in need of a high-quality option for their set up, whether you have a CODE or not. A single input makes it easy to plug and play and the 24kg weight ensures you won’t break your back carrying it to practice. It’s also Marshall’s most affordable friendly speaker cabinet, making it a great choice for those on a budget.
We are very proud to present to you a pleasant surprise I must say from way back when folks this is prime Time beginning of that Golden Era of some of the GREATEST QUALITY Acoustic guitar that FENDER ever had the smarts to Import… that’s right these are Japanese crafted beauty’s . Built back in the day when Japan had the economy riding high while US guitar builders were getting bought out by business folks not guitar builders and US economy was in the tanker just a little brief history reminder… Fender & Gibson were under the gun to cut costs and re-structure if they wanted to stay alive and that they did…. CBS , Norlin…. And others cut back on the high quality woods they once enjoyed and relied upon the reputation the US had for making great guitars basically reputation from the late 50’s – early 60’s To about 68-69 or so…. Then quality went down no doubt…. Right then it was prime time for Japan Luthiers to strike and they did…they stepped up the quality from the funny toy grade guitars we saw here in the states back when I was a kid you could get a decent cute player electric guitar at the Pawn shop in about 1965 for about $69.00 in fact my dad bought my 1st electric guitar there for $69.00 … I loved it—it was a “ KENT” and it sounded very good threw my Silvertone amp….. ..Kent is a offspring of Greco which is a factory behind making many brands buildby Fujigen Gekki…. Ok what this Fender beauty traces back to the great FujiGen Gakki in 1974 according to its serial number… making this beautifully preserved SOLID TOP Vintage Japanese guitars 40 years old a true vintage guitar in its own right. It was during the time when this guitar was built that the Japanese Luthiers set out to make some of the most righteous guitars period… fit – finish - workmanship & materials used are the good stuff folks….. This full size Dreadnought Acoustic guitar is a replica of the Martin designed D-28 known to be one of the finest most prolific designs the US Martin & co ever produced. This Fender F310 is of a High Quality example, The top is Solid Spruce straight grained with some nice figure and wow it has 40 years of patina to its color and finish and overall vintage appeal is Very strong… I was drawn to this example it sounds deep and rich and complex with an excellent volume And its highs ring threw when cording and finger picking , This guitars Back & sides are true to the masterful D-28 desigh …. High quality ROSEWOOD just beautifully grained see the pics for more detail Its absolutely beautiful back – sides are all east Indian Rosewood the fingerboard may be Brazilian Rosewood by its looksa very high grade non theless, the bridge appears to be Ebony wood….. the Bridge is nice and flat to its top which is also nice and straight, action is very good medium low and adjustable. The top has a couple of minor doinks see the pics not bad at all and certainly nothing remotely enough to detour from its vintage Gorgeous looks , no cracks anywhere found , bindings are very food, overall this guitar is an EXTREMLY CLEAN example aside from the afore mentioned . This guitar is in top Vintage used condition and is easily a 9//10 Fit and finish I suggest this was built but a high level Journeyman and can compete or compare with A nice vintage Yairi or Morris or Gibson or Martin for that matter…. .
Usual general wear. Some noticeable impression marks on face. Piece of decorative trim missing from headstock. Plays but Action is high. Neck truss needs adjusting. There is a slight buzz with action as it is (sounds like it's from bridge area). Frets look good. Not perfect but a classic in good condition in need of a little tune up. SOLD AS IS. Ships wrapped and secured inside a Road Runner hard shell case which itself will be plastic wrapped. Ships Priority from Alaska.
This guitar manufacturer started out as a parts supplier in the early 1970s. Atlansia didn't begin production of guitars under their badge until infamous engineer and designer Nobuaki Hayashi of Matsumoku fame became the company's president and chief designer in the late 1970s. Since then, Atlansia has continued to produce cutting-edge guitar designs in Nagano, Japan. The company did not make any other badged guitars other than namesake Atlansia.

The Strat didn’t just sound different, its aesthetics and ergonomics were totally unique and innovative for its time. Instead of a standard slab body, the Stratocaster had double cutaways and was contoured in a way that had never been seen on a solid-body guitar. Originally built for legendary western-swing musician Bill Carson, it was quickly adopted by rock ’n’ roll pioneers like Buddy Holly and Hank Marvin, and has been the tone behind countless Top 40 hits.
Continuing with the rock and metal theme we’ve got going, we come to the Schecter Omen 6. At the time of this writing, the Omen 6’s price on Amazon is about $50 cheaper than you’ll find anywhere else. I hope that continues long after I publish this, because the Omen 6 is an amazing guitar and finding it under $300 is a steal (and may not last long).
The Fender Stratocaster is a model of electric guitar designed in 1954 by Leo Fender, George Fullerton, and Freddie Tavares. The Fender Musical Instruments Corporation has manufactured the Stratocaster continuously from 1954 to the present. It is a double-cutaway guitar, with an extended top “horn” shape for balance. Along with the Gibson Les Paul, it is one of the most often copied electric guitar shapes.[2][3] “Stratocaster” and “Strat” are trademark terms belonging to Fender.
Earth Quaker Devices – Have you ever heard a song and wondered “how did they get that sound?”. If it was a recent recording there is a good chance these guys were behind it. They make an incredibly wide range of pedals that all go from great quality, usable pedals for almost any style to the weirdest, most wonderful tones that you have never heard before.
In 2005, after two years of research and development utilizing Jimmy Page’s actual guitar, Gibson Custom Shop issued a limited run of Jimmy Page Signature guitars based on Jimmy Page’s No. 1 1959. This time, Gibson worked directly from Jimmy Page’s actual guitar, which he lent to Gibson for the project. The guitar featured just one push-pull pot, just like Page’s No. 1, which reversed the phase of the pickups in the up position, which in Page’s own words gave “a close approximation to the Peter Green sound.” Gibson also went to great lengths to replicate the accuracy of the pickups, creating two custom pickups, which were available only in this guitar. The pickups were based on the Burstbucker vintage-style pickups, but featured stronger Alnico magnets and slightly higher output than the other Burstbuckers, as well as slightly higher treble response, which accurately reproduced the sound of the pickups in Page’s guitar. Gibson also replicated the neck profile, which was heavily modified prior to Page acquiring the guitar, and the Grover tuners that Page favored.
This is an American Gibson Les Paul electric guitar played on the both pick-ups setting and is played through a Fender Bassman '59 Reissue with old valves in. This soundfont has the same presets as the Fender Jaguar above (except it does not include the slaps and slides preset) and is also recorded with the volume on the edge of break up on the amp (read the Fender Jaguar above for description of amplifier setting). This guitar is suited to jazz and blues but can easily be used for rock if used with more distortion. It has a very full rounded sound with good sustain and when played harder has a bite to the attack. This guitar is a classic that has been used in alot of types of music.
The Yamaha's FG series FGX800C is a perfectly machined instrument. If there is one thing Yamaha is known for, it's the quality of their mass-produced acoustic guitars, which people like to pooh-pooh due to the romanticization of extremely expensive handmade guitars. Yamaha has perfected this machining process to a point where you wouldn't really be able to figure out if the instrument was put together by a luthier or if it was made on a factory floor somewhere. This is the case with nearly every accessible guitar these days thanks to machines reducing errors and driving prices down.

THE CONTROL CAVITY Routing the control cavity is just as important as the neck pocket but with a couple more steps. The best thing to do is to cut out the plastic cover. Trace the pattern that you came up with for it on the plastic then cut it out with a jig saw. Use a fine tooth blade to prevent the plastic from chipping and will also yeild a smoother cut. Once this is done, take your template and reverse it, trace the patern on the back side of the body. Next set your router to a depth that is the same as the thickness of the plastic plate and rout the cavity working out to the line you drew. I do this free hand since the first cut is too shallow for a template. Be careful when you do this and test fit the plate you cut to make sure you get a goo fit. Then you will draw another line about 1/4" along the inside of the cavity you routed out, leaving extra room in areas for the screws you will use later on to secure the control plate. Rout this area out in the same way, working out to the line you drew. When you start to get close to the half way point in the wood start to think about how much wood you need to leave at the bottom. Usualy 1/4" is good but make sure you are careful! I miscalculated once and ended up going all the way through the body. Bad experience. 

Popularity also was a critical factor in our choices, although we generally passed over a few best-selling reissues or boutique clones in favor of the real deal. So even though the Bubba Bob Buttcrack Tube Overdrive may sound more soulful than an original Tube Screamer, if it’s little more than a copy with slightly upgraded components, it didn’t make the cut.
“I started to get really frustrated, and I said, ‘I know! I’ll fix you!’ I got a single-sided Gillette razorblade and cut round the cone like this [demonstrates slitting from the center to the edge of the cone], so it was all shredded but still on there. I played and I thought it was amazing, really freaky. I felt like an inventor! We just close-miked that in the studio, and also fed the same speaker output into the AC30, which was kind of noisy but sounded good.”
The OO-18E was basically the small-bodied OO-18 acoustic with mahogany back and sides, spruce top, and the ring-mounted DeArmond tucked right at the end of the fingerboard. These featured one tone and one volume control, with large two-tone plastic knobs situated down on the lower treble bout. The first prototype was serial number 166839. OO-18Es were produced from 1959 to 1964. Around 1,526 of these were produced.
If you feel that you must attempt a setup on your own, and you have a suitably worthless guitar to work with, then there are a few pieces of advice that you should know. When adjusting the truss rod on any guitar (this changes the bend or warp in the guitar neck) you want to move in small, one quarter or less turns. Over-tightening the truss rod will lead to a back-bend which can permanently destroy your guitar’s neck. Loosen the rod to bring it from this kind of a bend to flat. From there, you will want a slight amount of sag in the guitar neck to allow the strings room to vibrate. Intonation on an electric guitar is achieved by making sure that the pitch of the note when a string is struck open matches the pitch of the note as struck at the twelfth fret of that string (one octave higher). If the note at the twelfth fret is higher, the string should be slightly loosened at the bridge (achieved by moving the saddle towards the neck). The opposite is true for flat sounding notes at the twelfth fret. It is best to use a high quality tuner when intonating an electric guitar.
Guitar from Spain is the best online store to buy the best spanish guitars online: Classical guitars, Flamenco Guitars, Acoustic Guitars and electro acoustic guitars made in Spain from the best spanish guitar makers at spanish local prices. These unique guitars will be delivered from our warehouse or from the manufacturer's bench to your door, avoiding extra costs or double margins. Because we only sell guitars from the most reputable Spanish manufacturers, you will be assured to buy only the best spanish guitars available with 2 years warranty and certified from origin. Spanish guitar brands like Alhambra Guitars, Raimundo Guitars, Ramirez Guitars, Admira Guitars, Camps Guitars, Rodriguez Guitars or Prudencio Saez Guitars are among the most reputable and best sounding guitars in the world. These guitars are manufactured in Spain, the land of the flamenco guitar and the classical guitar. At Guitar From Spain you can also buy steel stringed acoustic guitars, western guitars and electro acoustic guitars made with the same traditional craftsmanship and know how acquired through centuries of guitar making. We also have special guitars as Bandurria (Spanish mandolin), Laud (Spanish lute), Cuban tres, timple canario and special sized guitars as Cadete (guitar 3/4) Requinto (Guitar 1/2) and Senorita (Guitar 7/8). Compare our Spanish Guitars with any other "asian made guitars" at the same price and you will be amazed with the diference in quality and sound that you can get. Do not settle for imitations, buy the original, buy Guitars from Spain.

Gibson, like many guitar manufacturers, had long offered semi-acoustic guitars with pickups, and previously rejected Les Paul and his "log" electric in the 1940s. In apparent response to the Telecaster, Gibson introduced the first Gibson Les Paul solid body guitar in 1952 (although Les Paul was actually brought in only towards the end of the design process for expert fine tuning of the nearly complete design and for marketing endorsement [2]). Features of the Les Paul include a solid mahogany body with a carved maple top (much like a violin and earlier Gibson archtop hollow body electric guitars) and contrasting edge binding, two single-coil "soapbar" pickups, a 24¾" scale mahogany neck with a more traditional glued-in "set" neck joint, binding on the edges of the fretboard, and a tilt-back headstock with three machine heads (tuners) to a side. The earliest models had a combination bridge and trapeze-tailpiece design that was in fact designed by Les Paul himself, but was largely disliked and discontinued after the first year. Gibson then developed the Tune-o-matic bridge and separate stop tailpiece, an adjustable non-vibrato design that has endured. By 1957, Gibson had made the final major change to the Les Paul as we know it today - the humbucking pickup, or humbucker. The humbucker, invented by Seth Lover, was a dual-coil pickup which featured two windings connected out of phase and reverse-wound, in order to cancel the 60-cycle hum associated with single-coil pickups; as a byproduct, however, it also produces a distinctive, more "mellow" tone which appeals to many guitarists. The more traditionally designed and styled Gibson solid-body instruments were a contrast to Leo Fender's modular designs, with the most notable differentiator being the method of neck attachment and the scale of the neck (Gibson-24.75", Fender-25.5"). Each design has its own merits. To this day, the basic design of many solid-body electric guitar available today are derived from the original designs - the Telecaster, Stratocaster and the Les Paul.

I have established a broad network of invaluable contacts in the vintage guitar business. Please let me know what you are looking for, and I'll do my best to find it! Also, I am paying the highest prices for clean lefty vintage guitars. Let me know what you have; I'll be happy to work out a deal you will be happy with. I do want to mention that I buy righty guitars on ocassion as well, especially those that can be easily converted to lefty, including Fender Strats and ES-335/345 guitars.
Like most things involved with creative pursuits like making music, there isn’t a steadfast right or wrong way to do things, but if you encountered any of the problems above you’re definitely doing things wrong (unless you play in a German nihilist industrial noise band, in which case, go nuts). This article will help you avoid those scenarios by describing some of the basic rules and suggestions for placing different effects in the ideal order in your rig’s signal chain and how to achieve the best possible tones when using several stomp boxes together. If you’ve ever wondered how to put together your own pedal board, this info will give you a good start toward obtaining the best sound and most versatility out of your rig.

There are several factors to consider when establishing a good guitar tone. Here are some guitar tone tips.  Lets start with electric guitar tone. With electric there are three major factors to consider…the guitar, the amp, and the effects. There are all types of guitars with all types of pickups. Single Coil pickups and humbucking pickups are the two main pickup categories. I prefer humbuckers for the simple reason that they are less noisy. I like the tone of a good single coil pickup but I have never had much luck with keeping them from buzzing terribly. This is especially a factor when you are playing gigs in dive bars or clubs with bad electric wiring. You are much better off with a humbucking pickup. If you are gigging musician I would suggest having at least one in your arsenal. Generally speaking your Fender strats have single coils and your Les Pauls have humbuckers.


By 1968 (and probably with the union of Unicord), Merson and Gulf + Western, Univox amps had begun to employ a Japanese-made chassis in Westbury-made cabinets, still with the high-quality Jensen speakers. These combined tube output with transistorized components. They were covered with a black Rhinohide vinyl and sported a silver plastic logo with stylized block letters – initial cap with a little tail off the left followed by lower case letters – typical of the earliest imported Univox guitars, on the black grillcloth.
In the 1980s, digital rackmount units began replacing stompboxes as the effects format of choice. Often musicians would record "dry", unaltered tracks in the studio and effects would be added in post-production. The success of Nirvana's 1991 album Nevermind helped to re-ignite interest in stompboxes. Some grunge guitarists would chain several fuzz pedals together and plug them into a tube amplifier.[47] Throughout the 1990s, musicians committed to a "lo-fi" aesthetic such as J Mascis of Dinosaur Jr., Stephen Malkmus of Pavement and Robert Pollard of Guided by Voices continued to use analog effects pedals.[48]
Eddie's Guitars specializes in the finest electric guitars available today. We have spent many years seeking out the best builders, brands and models available from yesterday and today. From classics like Fender Custom Shop and Gibson Custom Shop to boutique builders like Collings, PRS, Tom Anderson, Grosh and John Suhr we have every avenue of the sonic world of guitar covered.
The D-120's all-mahogany body strays from conventional spruce top design, which results in a warmer and more articulate tone. This particular tone is ideal for guitarists who sing, and for those who accompany vocals, it also blends well with conventional spruce top acoustic guitars, easily cutting through the mix with its lower-mids emphasized voicing. And since the body is crafted from solid mahogany, you can be sure that the instrument grows with you, sounding better with age.
Description: Body: Maple - Burled - Top Wood: Maple - Burl - Neck Attachment: Set - Neck Wood: Mahogany & Maple - Neck Construction: 3 Piece - Fingerboard: Ebony - Frets: 20, Medium - Inlay: Pearloid & Abalone - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: ART-W - Bridge Construction: Ebony - Cutaway: Single - Hardware: Gold - Circuit Type: Passive - Pickups: Super 58 - Pickup Configuration: H-H - String Instrument Finish: Blue Lagoon - String Instrument Accessories: Hardshell Case
PRS started off in the 1990s. At that time, it seemed Les Pauls were being swapped in favor of a PRS guitar. PRS leveraged this opportunity to continue the trend, making PRS more accessible to all. Hence, they launched another line of product with affordable price tags – the SE guitars. Nonetheless, one cannot consider SE guitars as the beginner’s guitars, since they all flaunt with high-end specs like other instruments. Through these guitars, one gets an opportunity to enjoy playing a pro guitar without causing a blow to your budget.
WIRING Lay your beautifully finished guitar on a soft towel so you don't scratch it and cover the back with a cloth as wel so you don't splatter solder on it. How you wire you guitar up depends on the layout you have chosen. Mine was a simple one tone, one volume and three way switch set up. I have gone with the Les Paul set up on other guitars which is a two tone and two volume before as well. What ever set up you go with just follow the schematic that either came with you pickups or get one from Seymour Duncan. They also have instructional videos that are done by Seymore Duncan himself on Strats and Les Pauls. I recomend watching these if its your first time wiring a guitar.
Starting from the body, we see the standard Les Paul shape. The tonewood of choice is mahogany, as expected, but this time it comes with a maple top. The top of the guitar arches slightly just like the original Les Paul does. In terms of details, we see a white binding around the top section that really stands out on the dark matte finish.  It's something to behold.
Solid Body: This build is rather self-explanatory, meaning there is no sound box (as typically seen in other instruments, especially acoustic guitars) but instead relies on an entire electric pickup system to gather the vibrations of the strings to portray your sound. This typically dominates the preferred ‘guitar type’ category unless you’re aware of what the differences are in terms of sound (telecasters, Ibanez, etc.). The perks of this solid build include the ability to be amplified at very high volumes without feedback worries, giving us more combinations when it comes to shapes\designs, and are very responsive to the use of effects since it’s nearly entirely dependent on amplification. Preferred genres? Rock, punk, metal, classic rock, etc.
The Ibanez RG series is basically synonymous with shreddable metal music. Inspired by the classic JEM series of the glammy 80s rock years, this GRGR120EX guitar is perfect for the guitar player who aspires to be a real metalhead. The body is made of solid alder and it comes with a slick black binding. There are two super-high-output, extra-snarly Infinity R pickups that will respond well to overdrive and distortion pedals. Moreover, a rosewood fingerboard with classic Ibanez sharktooth inlays and sharp black hardware make this guitar look like the real deal.
The late 60s and 70s produced even more bizarre and berserk creations. The birth of Mayfield and Mullen’s VOX King Wah pedal sealed its place in guitar history during overbearingly long, Clapton-esque guitar solos. The 1978 Pro Co RAT, whose design was a re-imagining of the Arbiter Fuzz Face, arose partly from error: A botched resistor band created a harsher, clipped audio waveform. Its use has supported nearly all “alternative” rock genres in the last 30 years: 80s punk, American indie rock, Grunge (the RAT played a crucial part in Cobain’s quiet-loud-quiet-loud composition), not to mention Britpop and grindcore.
When jazz guitar players improvise, they use the scales, modes, and arpeggios associated with the chords in a tune's chord progression. The approach to improvising has changed since the earliest eras of jazz guitar. During the Swing era, many soloists improvised "by ear" by embellishing the melody with ornaments and passing notes. However, during the bebop era, the rapid tempo and complicated chord progressions made it increasingly harder to play "by ear." Along with other improvisers, such as saxes and piano players, bebop-era jazz guitarists began to improvise over the chord changes using scales (whole tone scale, chromatic scale, etc.) and arpeggios.[2] Jazz guitar players tend to improvise around chord/scale relationships, rather than reworking the melody, possibly due to their familiarity with chords resulting from their comping role. A source of melodic ideas for improvisation is transcribing improvised solos from recordings. This provides jazz guitarists with a source of "licks", melodic phrases and ideas they incorporate either intact or in variations, and is an established way of learning from the previous generations of players.
In 2003, The Blues, a PBS-TV series produced by famed director Martin Scorsese, traced the roots of the blues from Africa to modern day society, showing how it inspired other generations of musicians. While in production, Marshall Chess got an e-mail from Chuck D saying that he heard he was doing a film that connected the blues to hip hop and that he wanted to be part of it. Chess was happy to hear Chuck D say "Electric Mud was one of his favorite, most influential albums and that all the early hip hop guys were inspired by it," affirming a connection he thought had happened. In the episode titled Godfathers and Sons, the focus is on the Chicago blues, Chess records and the effect of Electric Mud on Public Enemy, with Chuck D coming to Chicago, led on a historic blues tour by Chess. There, Chuck D's feverant appreciation of EM got him to reassemble the musicians from the sessions to perform material from it for the upcoming 20th Anniversary Chicago Blues Festival. In keeping with the experimental vein of the record, Chuck D added a turntablist (Juice) and a rapper (Kyle Jason) to the band, re-naming the group the Electric Mudcats. Having the material played at a blues festival showed how the album had finally come full circle, from being hated to being respected and enjoyed.
ESP LTDs are a ripoff. All the money goes into the finish and nothing else. Cheap hardware and poor electronics. All of the LTDs I've ever owned couldn't stay in tune worth a damn, have noisy, pop-y switches and crappy pots. I have the Viper 400, and it's an overrated turd. Luckily I got it for a steal. Thing can't stay in tune AT ALL. I will be replacing the alleged Grover tuners with real Grover lockers. That still doesn't solve the issues with the soft finish and ultra-noisy electronics. Plus it has a humpy neck, a cracking neck joint (like all of my LTD set-necks) and the frets were likely leveled by a monkey considering the quality.
The first rule of making repairs to any instrument is to decide if the value of the instrument, financial and otherwise, is worth the price of the desired repairs. If the repair is small enough to be comparable to guitar setup cost (about $50) then it is almost always worth having done. However, for large and expensive jobs like painting and neck replacement, the cost can easily outweigh the need of repair.

Taylor also has a Build-To-Order program that allows anyone to design their very own guitar. There’s an extensive menu of guitar options starting from tonewoods, including species and grades that aren’t offered through Taylor’s standard line; inlay, binding and purfling options; finish options such as solid colors, sunburst, or vintage finishes; wood accents like a backstrap, armrest or truss rod cover; neck options such as scale length and neck profiles; and finally body shapes including the deep-body Dreadnought and the new Grand Orchestra.

I sold my fender squier stratacaster for this guitar.when I opened the box it was so beautiful nothing like what pictured showed. Easy to tune and the amp is wanderful. This guitar comes with great surprises as well. Gibson has done it again. This guitar is great for a beginner. The only flaw is that it doesn't have a pick guard but those are cheap to buy. Would buy again.
Most of the guitars, banjos and mandolins my customers use and collect have been made by major manufacturers such as Martin, Gibson and Fender or a few superb handcrafters such as D'Angelico and Stromberg, but over the years, by far the greatest number of instruments purchased in the USA and worldwide have been lower-priced student models. Prior to 1970 most student grade instruments sold in the USA were made here by companies such as Kay, Harmony and Regal in Chicago or Oscar Schmidt of Jersey City, New Jersey, and Danelectro of Neptune, New Jersey. When I started out playing and collecting guitars in the mid 1960s, brands such as Harmony, Kay, Stella, Silvertone and Danelectro were the standards for student use. We saw very few Oriental imports.

• Wound Up: String windings directly affect tone and playability. Round wound strings have more “zing” – sustain, responsiveness and bite. Flat wound strings have a smoother and more consistent tone regardless of attack, which makes them a favorite of jazz players, like the great Gibson ES-350 legend Barney Kessel. Blues guitar kingpin Jimmie Vaughan also uses flat wounds for his vintage tone. And they offer less resistance than round wound strings, so they can be beneficial for rapid, even toned performance and squeak less.
{ "thumbImageID": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "defaultDisplayName": "Gibson Les Paul Faded 2018 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Worn Cherry Black Pickguard", "sku": "sku:site51500000137380", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard-1500000137380.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001-00-60x60.jpg", "imgAlt": "" } , { "name": "Worn Bourbon Black Pickguard", "sku": "sku:site51500000137381", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard-1500000137381.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001-00-60x60.jpg", "imgAlt": "" } ] }
The stars of the show are inarguably the pickups: the EMG Retro Active Hot 70 set, which goes for $200 alone. This combines a ceramic humbucker at the bridge and Alnico V humbucker at the neck—both open-coil—to produce the hot tones of Van Halen and other ’70s hard rock acts. They’re active pickups, too, wired to a FET preamp that minimizes noise and levels outputs.

It wouldn't be called a tribute if it didn't follow convention, so having a mahogany body with an arched maple top is expected. Epiphone also designed the neck to mimic the playability of old LPs, giving this guitar a 1960s SlimTaper D profile. However, what makes the Epiphone Les Paul Tribute Plus stand out is the use of two Gibson USA '57 Classic humbucking pickups, which essentially gives this Les Paul a more premium Gibson voice, at a fraction of the price.
When you hit a string it will vibrate. It will continue to vibrate until the energy put into it is expended. Where does that energy go? Well, it is expended through movement. That movement is what the pickup "sees" and translates into sound. In a world where 100 % of the initial energy imparted by the strum to the string was expended through movement, wood doesn't matter.
There's a sick little used Chinese Peavey going for $90 at my local guitar shop. It plays great, but nobody seems to want it. I'm already picking up a MIM strat from there, but after I save up a bit more change I think I'll grab it as well. You always have to dig for the good players, and sometimes you just happen to be lucky enough to find a cheap one on a fluke, doesn't matter where it's from.

There’s still a lot of confusion over Japanese- and Korean-built guitars from this era in regards to trademarks, who built them, when they were offered, and the connection between them all. However, many of these guitars are high quality and you should always pay close attention when encountering an unknown trademark. If a guitar was produced at one of the aforementioned factories, it could very well be a treasure, just like your Lotus.

Unfortunately, it appears it is no longer possible to grab a Standard MIM Telecaster for under $500. Still, the Standard Telecaster remains a solid option when it comes to reasonably priced guitars, and it is a great alternative to the American Tele. However, if this increase doesn't set well with you, and you aren't digging the Modern Player Telecaster Plus, I suggest checking out what Squier has to offer.

Want to know more about how to distinguish all these guitars? Until a few years ago there wasn’t a good (or any!) English language reference book for Japanese guitars of the 1960s. But my co-author on this piece, the esteemed Frank Meyers of Drowning In Guitars, has written an excellent primer on this subject which can help demystify the confusion around a lot of these guitars. You can pick up your own copy here.


But you should remember that it is still a great value and the best guitar for the money. For this price, I don’t think you will get a better guitar anywhere else. If you are an intermediate or expert level player, this one is not for you. Let’s check out some technical features of the guitar: it comes with bolt-on neck joint, 12”radius of the fingerboard and nickel hardware etc. 
The auctions continue on our eBay store, including last remaining production samples of several models, and other unique instruments, including made in Japan JP models, Triturador basses, Tony Campos Signature Tremor basses, acoustic guitars and accessories. Check out the current listings, there will be new items posted every week: http://bit.ly/1caL5ah
It also has an overwhelming amount of sheet music in it. These music sheets allow you to practice what is being taught in the given chapter, which is nice, but going through the books, I felt there was a lot left unexplained. This was probably a result of them trying to simplify things as much as possible, but this actually leaves holes in the padawan guitarist's knowledge.

I had a 1984 Jackson Randy Rhoads Custom with a serial # in the low 400′s…that thing would sing on a note with high gain and boost with a TS-808 Tube screamer like a Sustainiac guitar…problem was the bridge was mislocated and it wouldn’t intonate correctly…sent it back…made them replace it with a new guitar (didn’t want plugs in it)…the new one had (ermmm…still has as I still own it) the EXACT same pickups, hardware down to the tuning machines, etc…EVERY single piece of hardware was moved over to the replacement (and in the case of the bridge pickup it is a proven fact as that was/is a retail version of an SH-6 wired for series/single coil/parallel…along with the pickguard with the additional hole for switch)…same types of wood used (3 piece maple neck through construction with poplar wings) yet the replacement has NEVER sung on a note. So what does that say? I have to say that the replacement does sound “better” overall in some intangible way…glassier I guess…longer sustain…yet it REFUSES to go into a sustained feedback loop.
Last fall, Ubisoft released a new version. But Rocksmith 2014 is considered a replacement rather than an update: The company is trying to rebrand the franchise not as a game but as a teaching tool. The box bears a fat label proclaiming "The fastest way to learn guitar," and Ubisoft launched an ad campaign promising that Rocksmith 2014 could teach prospective shredders to play guitar or bass in just 60 days.
Tube amps use the height of the 1940s electronic technology to give out what is widely considered the best sound quality to date. Since some people tend to be confused by this, it’s important to note that only their sound rendering circuitry is based on vacuum tubes (or lamps) while the equalizers and assorted bits employ transistors like any other piece of modern electronics, with no bearing whatsoever on how the sound will come out.

{"product":{"id":"114488369","stock":"instock","price":"799.99","name":"Legacy Solid Body Electric Guitar","download":false,"sku_id":"114488369","checksum":"402390681023","rep_id":"site5114488369","displayId":"114488369","sku_display_id":"114488369","sku_rep_id":"site5114488369","gc_pro":false},"category":"Electric Guitars","pageName":"product_detail","subcategory":"Solid Body Electric Guitars","dept":"Guitars"}

Fender Kingman "C" Custom Shop Acoustic/electric in Fiesta Red, 1 of 150 worldwide. This was a limited production that came out of the custom shop in Hartford, CT. Has a Fishman pickup. Not a nick, ding or blemish will you find on this guitar, almost museum quality. Comes with original Fender case(perfect shape), Certificate of authenticity and other paperwork and allen wrench. Ships to the US only.


Power valves (tubes) can be overdriven in the same way that pre-amplifier valves can, but because these valves are designed to output more power, the distortion and character they add to the guitar's tone is unique. During the 1960s to early 1970s, distortion was primarily created by overdriving the power valves. Because they have become accustomed to this sound[dubious – discuss], many guitar players[who?] favour this type of distortion, and thus set their amps to maximum levels in order to drive the power section hard. Many valve-based amplifiers in common use have a push-pull output configuration in their power section, with matched pairs of tubes driving the output transformer. Power amplifier distortion is normally entirely symmetric, generating predominantly odd-order harmonics.
The word distortion refers to any modification of wave form of a signal, but in music it is used to refer to nonlinear distortion (excluding filters) and particularly to the introduction of new frequencies by memoryless nonlinearities.[32] In music the different forms of linear distortion have specific names describing them. The simplest of these is a distortion process known as "volume adjustment", which involves distorting the amplitude of a sound wave in a proportional (or ‘linear’) way in order to increase or decrease the volume of the sound without affecting the tone quality. In the context of music, the most common source of (nonlinear) distortion is clipping in amplifier circuits and is most commonly known as overdrive.[33]
Amazing guitar for the price. Honestly plays almost as good as the Paul Reed Smith I used to have. Light weight, great sustain, built in tuner and the pick ups produce a great sound. I was shocked at how good the guitar was... HOWEVER - the amp is total crap. It cracks and pops... my suggestion is to buy the guitar by itself and spend the $100 you save on a real amp (many starters that are superior to this one are the around that price.
But there are two things in which latency matter. Latency is time. Every digital thing ever adds latency. If you’re a well trained musician or studio rat, you can hear about a millisecond of latency if you’re listening closely. You won’t likely be bothered by 1ms latency, but 10ms might be a bit of an issue, and 100ms makes some things completely unworkable.
These special qualities have been used for centuries to create and build various instruments with differing levels of success. Some tone woods do it better than others so, are often more vigorously sought out and because of their growing rarity (due, primarily, to over harvesting) also vary in expense, the rarest most hard to find being the most expensive, of course.
Rickenbacker: From making world’s first electric guitar to making the most iconic guitars of Rock’n Roll, Rickenbacker has a history of innovations in guitar industry. Their guitars are still made in the old way. Owning a Rickenbacker is pretty much like owning a classic muscle car, yes there may be more modern guitars out there but no one’s got the mojo of a Rickenbacker.

One of the biggest hits of all-time, this song incorporates everything that is 80’s pop and is performed in the key of F# major, in 4/4 time. Lauper originally didn’t want to sing it since the original version was written by Robert Hazard, who wrote it from the perspective of a man. Eventually, the singer released her version of the song and the rest is history. 
Just knowing three chords will enable you to play all of these, albeit sometimes in a key that doesn't suit the song too well. As Rockin Cowboy illustrates, chords come in 'families', so if you understand that, songs become far more predictable. Sometimes I play with others, and when they try to explain that this new song 'has G, C and D in it', all I need to know is the key - in this case, G. The other two chords are virtually inevitable, but that fact seems to have escaped them!

What is it about the Japanese and the Ventures? I mean, I cut my teeth with the Ventures. They were the perfect band to learn guitar from. The Ventures took songs with often complex harmonic structures—like the wonderful Johnny Smith classic—and stripped them down to their basic melodies, gave them a simple rock groove, and played them clean. I had the sheet music to Smith’s song, but there was no way in you know where I was gong to play off that. But follow along with the Ventures’ single? You bet!
With sharp double-cutaways and the recognizable Rickenbacker body shape made from maple, the semi-hollow Rickenbacker 330-12 12-string electric guitar has proven to be one of the brand's most popular models since the 1960s. The 330-12 has been used for its jangly sound, perfect for pop and various other genres, by the likes of Tom Petty, Johnny Marr, and Peter Buck, to name a few.
Years of hard-earned success and fame have not changed his down-to-earth attitude. Even though he has become one of the world’s richest rock stars, he hasn’t married a supermodel or become a pompous art collector. Instead, he’s remained true to his working-class roots, spending his spare time building incredibly cool kustom cars and cruising the streets with his car club buddies, the Beatniks of Koolsville.

The kind and quality of woods and other materials, as well as features such as onboard electronics, also figure in the price of a guitar. With a well-built guitar that is made using quality materials, you can be sure to have a sturdy instrument that will last for years, as opposed to a low-end product that you may need to replace because the neck snapped.


Designed in collaboration with the legendary Guns N' Roses guitarist, this limited-edition Slash Firebird won't last long. After all, as Slash himself says, "Who doesn't want a Firebird?" Limited to a production run of just 900, worldwide, this version of the iconic guitar combines tradition, like the reissue Kluson banjo-style tuners, with some of...  Click To Read More About This Product
I am a fan of inexpensive guitars. Why but something so valuable you can’t take it out or afraid it will get damaged. Get an inexpensive guitar that is closest to the expensive ones you desire. Basically the construction and woods are the same just made inexpensively to sell to the masses. Watch who plays the secondary brands and get full cred. I have a squire cabronita, squire telecaster with upgraded coil tapped humbucker/single coil pickups, gretch electromatic single cutaway soildbody, and 2 Harley Benton les pau l type guitars with p90s and coil tapped tumblers for less than 175.00 each. Every guitar is a beauty and a joy to own.
Hi everyone! I have a quick question regarding string action. I have just gotten my 2003 Standard set up a few months ago, but I am having trouble with how low the action is; strings slip off of my fingers during bending now. If I just turn the screws on the Tune-O-Matic bridge to heighten the action a little bit, without touching or adjusting the truss rod, individual saddles, or tailpiece, will that screw up my intonation?

This is one of our favourite cheap electric guitars and it certainly doesn’t suck thanks to its Alder body, comfortable “C” shape neck, snappy maple fingerboard and two Vintage-Style Single-Coil Tele pickups to provide that awesome tele twang. If you’ve always wanted a Telecaster and are just starting out in the world of guitar, this is a dream beginner’s guitar that is budget friendly and still completely high quality.
While it was produced, Ovation’s super-shallow 1867 Legend was the recommended guitar in Robert Fripp‘s Guitar Craft.[22][23] Tamm (1990) wrote that the acoustic 1867 Legend has “a gently rounded super-shallow body design that may be about as close to the shape and depth of an electric guitar as is possible without an intolerable loss of tone quality. Fripp liked the way the Ovation 1867 fitted against his body, which made it possible for him to assume the right-arm picking position he had developed using electric guitars over the years; on deeper-bodied guitars, the Frippian arm position is impossible without uncomfortable contortions”.[22]
Just as an Auto-Wah is a version of a Wah pedal controlled by the signal's dynamic envelope, there is an envelope-controlled version of a volume pedal. This is generally used to mimic automatically the sound of picking a note while the guitar's volume knob is turned down, then smoothly turning the knob up, for a violin-like muted attack. An example is:
An overdubbing session is ideal for air-guitar miking because there is no leakage from other instruments. I usually prefer to maintain total isolation between the two sources, placing the guitarist and amp in separate rooms. But for some production styles, the acoustic air mic can also do double duty as a distant room mic for the amp, with the ratio of pick sound to ambience determined by mic placement and amp volume. I've recorded some very hefty-sounding rock 'n' roll power chording this way, as well as a variety of vintage-style solos and rhythm parts. At the board, a low shelving or low-midrange EQ cut, combined with a subtle high-end boost around 4 to 6 kHz, will usually help these tracks jump out of the mix.
• Them Changes: Since the strings on acoustic guitars play a much more important role in projecting volume and clarity than strings on an amplified electric guitar, considering changing acoustic guitar strings often to keep an instrument sounding its best. Remember to wipe down the strings after playing and check for string damaging fret wear. Both can prematurely end a guitar string’s life.

Jump up ^ DeCurtis, Anthony (1992). Present Tense: Rock & Roll and Culture (4. print. ed.). Durham, N.C.: Duke University Press. ISBN 0-8223-1265-4. His first venture, the Phillips label, issued only one known release, and it was one of the loudest, most overdriven, and distorted guitar stomps ever recorded, "Boogie in the Park" by Memphis one-man-band Joe Hill Louis, who cranked his guitar while sitting and banging at a rudimentary drum kit.
The brilliance of Guitar Rig is the ability to create so many different tones. This is in large part due to the variety of amps that are modeled in the software. You have a choice between Citrus, Ultrasonic, High White, Tweed Delight, Plexi, and Lead 800, among others. I’m sure you can guess what Native Instruments’ clever amp names translate to in the real world.
The Triple Crown TC-50 is a three-channel amp, with independent preamps covering clean, low-gain and high-gain ranges. The front panel packs three identical sets of controls including gain, master volume, bass, mid, treble and presence, together with a two-way toggle switch that changes the channel gain and voice. There’s a small toggle switch for manual channel changing, and a pair of master output level controls, one of which is footswitchable. The feature-rich rear panel includes Mesa’s exceptional CabClone speaker-emulated output, with a balanced XLR, headphones socket and line out. The TC-50 also benefits from a footswitchable effects loop, separate reverb level controls for each channel, and MIDI switching for all the major functions. The Triple Crown’s clean channel is highly versatile, going from butter-sweet clarity through to edgy blues soloing, with a lot of control over that ‘just on the edge’ sweet spot. The Lo Gain channel is where the TC-50’s crunch and classic rock tones live, with a multi-layered overdrive and harmonic overtones that shift with varying degrees of pick attack. Flipping the toggle switch into Drive mode adds a subtle midrange bump, invoking JCM800-approved snarl and a dose of extra gain. The Hi Gain channel adds more of the same - lots more, so much so that in the upper reaches we think this is probably the most gain ever from a Mesa amp. No doubt about it, the Triple Crown has three channels packed full of world-class tone that only a handful of amps can compete with.
Because most electric guitars offer far more adjustability than acoustic guitars, the setup and adjustment of the guitar is more important than it is with acoustics, which don’t have much to adjust. We decided John and I would test the electrics first right out of the box, with their stock strings and factory setup, then get a professional to set them up with Ernie Ball Regular Slinky strings in gauges from .010 to .046—for decades, this has been one of the most popular string sets for electric guitars. Our setup technician was Avishay Shabat, who heads the Guitar Groomer repair shop in Woodland Hills, California, and who also manufactures his own line under the Shabat Guitars brand.

A combo amplifier is a unit in which both the amp and speaker is integrated. You plug a guitar into one of these, turn it on and you are ready to play. The obvious benefit of a combo is that you have everything you need in one standalone unit, while the sound tends to be optimized by the manufacturer to be the best it can be – there’s no worrying about matching it with a good speaker. Combo amps also tend to be cheaper than heads and, as such, are excellent for beginners. While some are very capable of small to medium-sized performance, the drawback is that combos are limited in power compared to a head. They also tend to be much heavier, which can be a pain when regularly transporting it.
Some Craigslist and EBay sellers have been claiming the 500 and 600-series Kents are made by Teisco. I think we’ve shown that that’s not the case. Some sellers also describe those early Kents as having “Ry Cooder” pickups. As most of you know, Ry Cooder is an incredibly talented multi-stringed-instrument musician. David Lindley, another great talent, gave him a pickup from an old Teisco guitar. The photo at left is exactly like it. Cooder put the pickup into one of his Stratocasters and liked the sound so much that he got another one and put it into another Strat. These pickups are also described as “gold foil” pickups. There are variations in the pattern of cut-outs on the chrome covers of different pickups. I don’t know if the others sound any different, but if I were looking for a “Ry Cooder Pickup”, something like the one pictured here is what I would be looking for. The pickups have become worth more than the guitars they are on, consequently, as the guitars are bought up and trashed for their pickups, their prices are going to rise.

{"eVar4":"shop: pro audio","eVar5":"shop: pro audio: signal processors","pageName":"[gc] shop: pro audio: signal processors: multi effects processors","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: pro audio: signal processors","prop1":"[gc] shop: pro audio","evar51":"default: united states","prop10":"category","prop11":"multi effects processors","prop5":"[gc] shop: pro audio: signal processors: multi effects processors","prop6":"[gc] shop: pro audio: signal processors: multi effects processors","prop3":"[gc] shop: pro audio: signal processors: multi effects processors","prop4":"[gc] shop: pro audio: signal processors: multi effects processors","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category2"}
I bought this Fender acoustic/electric guitar about 9 months ago. It has a wonderful rich tone, is easy to play and is beautiful. The grain on the mahogany is dark and beautiful. It lives up to its dreadnought name and can fill a large living room with its sound. The tone is deep, rich and mellow. Strings are separated enough for easy picking. Tuning pegs are of decent quality and once strings are broken in it stays pretty much in tune. Other than putting on some bronze phosphor strings I did not need to set the guitar up. I really haven't played it much with an amplifier so can't comment on the electronics, other than the built in tuner works well. The hardside guitar case is well padded and looks professional. I was a little concerned about buying a guitar over the

Description: Body: Mahogany - Body Construction: Semi-Hollow (Chambered) - Top Wood: Maple - Flamed - Neck Attachment: Set - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 24 - Inlay: Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Chrome, Diecast, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: HoneyBurst, Green
The guitar offers a carved mahogany top with a set neck and a slim-tapered profile (a shape normally reserved for more premium guitars). The rosewood fingerboard sports premium trapezoid inlays for a really pro look. The Alnico classic humbuckers are true, high-output gems that, paired with the set neck, will offer a rich, long sustain. There are two tone knobs and two volume knobs, as well as a three-way selector switch for all of those classic Les Paul sounds. The stop bar tailpiece and the LockTone Tune-O-Matic bridge give you rock-solid tuning stability, so you won’t have more frustrating retunes than you absolutely need.
OK, our math isn't so great, so we've gone ahead and included an 11th amp in this list of 10. Although it's way too soon to be declared "iconic," PRS Guitars' brand-new Sonzera series of amps have been hot topics in gear land since they were introduced at the 2017 Winter NAMM Show. Let's just call them "instant classics." Featuring a rugged steel chassis, custom transformers and road-ready construction, each Sonzera model delivers serious tone with maximum reliability.
Alvarez has always been an under-rated brand. Beautiful workmanship, great sound- an excellent value for the money. I have one of the old six string "dove" guitars and a Yairi 12 string: both are close to forty years old and both still sound and look great and have never needed any repairs. I also have an old Martin six string. I have done the "blindfold" test with friends to choose the best sound between the alvarez and the martin - alvarez wins every time.
• Fade to Bleak: Since there are no pickups, juice or amps involved in acoustic guitar playing in its purest form, string composition – which affects how a string responds to being struck and the retention of tonal qualities – is particularly important for acoustic guitars. Bronze, phosphor bronze and coated strings tends to be the preferred varieties, ascending in price. Bronze strings start out the brightest, but lose their high voices relatively quickly. Phosphor bronze offers a darker tone, but still with a clear, ringing top and the phosphor allows the strings to produce their optimum sound longer. On acoustic guitars, coated strings trade a longer life for less brightness, but good warmth and presence.
Probably one of the greatest is Glenn Schwartz, formerly of the James Gang and Pacific Gas & Electric. Considered to be a "white" Jimi Hendrix, he was asked by Jimi to play at what was to be his last birthday party. Glenn played behind his back and with his teeth (now with his gums) before Jimi ever did. Now out of the limelight (and out of his mind) Glenn plays (and preaches) on Thursdays at a blue collar bar in Cleveland. ONE F*CKING INCREDIBLE PLAYER. Should be on any list.
Add a maple top to the mahogany body, as do a great many Les Paul models, and a blend of characteristics comes forward. The mahogany’s depth and richness remain, but the maple provides added snap, clarity, and definition. It also tightens up the lows and adds more cut to the highs. For many players this sonic evolution is highly desirable, whereas others might prefer the smoothness of the pure-mahogany design.
The SIX6FDFM’s jaw-dropping aesthetics belie its price tag. It has an arched flame maple top on a bound mahogany body, a bound ebony fretboard, and a three-piece maple/purpleheart neck that has a colorful streak running down the middle. Only a Blue Space Burst finish is available, but, coupled with a matching headstock, it looks good enough to lick.

“Move up to Alnico IV and the power rating comes up and the frequency response flattens out – you get a balanced and natural- sounding response from the coils, but not so it’s boosting the treble. The mid-range stays quite constant as well. And then you go to Alnico V, which has the highest power. Then the bass and treble do get boosted and the sound starts to get more aggressive – more ‘rock ’n’ roll’, for want of a better term.
A neat recording solution for when you want the sound of a speaker running flat out, but without being thrown out of your flat by your neighbours!A practical method endorsed by those engineers who don't like to leave their comfortable chairs too often is to combine the above techniques by using two close mics, one on-axis and one off-axis, plus one distant mic a few feet from the cabinet. If the close mics have very different characteristics, for example a capacitor mic on-axis and a dynamic mic off-axis, you'll get an even greater choice of tonality, as you can vary the mic balance being recorded. Switching the phase of individual mics can often yield interesting combinations and, if you really don't want to leave that chair, you can also delay the ambience to increase its effective distance when it is combined with the other mics. Each millisecond of delay is roughly equivalent to 12 inches of added distance.
You are bidding on a previously owned and in good working condition Blackstar Amplification HT Studio 20H guitar amp head. This auction is for the amp and power cable you see pictured. No footswitch is included. Nothing else is included. It comes as pictured. Please take a moment to look at the pictures and get a better idea of what you are bidding on. This unit has some scuffs and dings from being moved around. It has been tested and is in good working condition.
2. Materials. The timbers used to make these guitars were sourced from every corner of South East Asia. These timbers were “old growth”; in plainer words, the timber was taken from established forests. The advantages of this type of wood are long term stability and strength. Further to this, many of these timbers were species that are now on the endangered list and are therefore illegal to log and/or export. Now, while we consider the cutting down of established “old growth” forest timber a crime, it would be an even bigger crime not to make the most of what is already there. Whilst the build quality of the modern Asian made guitar (i.e. China, Indonesia, Vietnam etc) is exceptional, most of the timbers used are “plantation” timbers or more overly “new growth” timbers. Though this forestation is certainly light years ahead ecologically, it tends to yield timber which is brittle and can be unstable, making many repairs, such as a broken headstock untenable.
This is the brand of guitars manufactured by a Japanese company and are available in India. The company creates incredible custom – shop instruments and high-quality original designs, liked by some of the best professionals on the planet. They produce electric guitars that provide high performance and are long-lasting in terms of duration and quality. E-10 is one of the most popular guitars of this brand. The starting price of ESP electric guitar is 16,000 INR approximately.
Not to mention the difference tones created when two pure tones (sine waves) are produced at the same time (which, important to mention - pure tones only exist in theory, every sound we hear is comprised of overtones...) - then the additional difference tones created by the interaction BETWEEN difference tones - it's basically a fractal relationship. Anybody who has spent a significant amount of time studying the physics of sound knows that the interactions that occur between sounds are so complex and immense that it's almost silly to assume that just because "wood isn't magnetic" that the natural resonance of the wood wouldn't in turn accentuate certain overtones over the fundamental tone coming off the string. You can't say that the note "has already left the string," when the note takes place over time - even a staccato note has an attack, sustain, decay, and release envelope much in the way that a synthesizer does (this is where the idea for artificial dynamics envelopes came from anyway).
The model designations of the archtops are unknown. Later these guitars would have either a PE or EP model designation, so presumably the ones in the photo did, too. One appears to be a full-sized, thick-bodied archtop with a rounded cutaway. Not much is visible in the photo, but it apparently had a single, white-covered pickup at the neck, block inlays and a white pickguard. The other guitar had a single pointed Florentine cutaway and was slightly smaller than, say, a Gibson ES-335. It’s impossible to tell the depth from the photo, but it looks as though it’s a thinline. This, too, had a single white pickup at the neck, moveable adjustable bridge, trapeze tail, large white pickguard (not modelled on a typical Gibson shape, by the way), a little plastic plate on the lower bout with volume and tone, with white knobs. The fingerboard has large white dots, with double small dots at the octave. The f-holes are three-part; the headstock Teisco three-and-three.
With a body shape that looks like it could have been cut out by hand using a saw in your garden shed, this Kay Old Kraftsman Sizzler guitar manages to be crude and quite fantastic at the same time. "Old Kraftsman" was actually a brandname used on Kay guitars sold by Spiegel stores. The maple neck gives it a rather Fender-like appearance, but this is in fact a set neck and not a bolt-on. 

Unless it's broken and will need to be replaced, start with obtaining a new nut that is anything to your liking, preferably a blank nut rather than a pre-cut to avoid improper string height. If cutting a blank try copying your old nut and make adjustments if needed using the neck as a guide after cutting out the nut. To do this take a sharp blade that is easy to work with such as an X-acto and cut the finish that holds the sides of the nut. Make sure to cut all of the finish as it will break apart when you take out the nut.
I’d like to think that I am a little more forgiving of slight finish errors than most, so most of the horror stories surrounding Gibson QC do not bother me too much. After all, one area of the body where the sunburst color doesn't fade at EXACTLY the same point all the way around? That sounds more like middle aged guys trying to save face around their buddies after their wives saw the credit card bill the next month and made them take it back.
With Dave Matthews playing an electric guitar in place of his usual acoustic, the band delivered a performance of “Samurai Cop (Oh Joy Begin)”, the lead single from Come Tomorrow, their record-breaking seventh-straight album to debut at #1 on the Billboard charts dating back to 1998’s Before These Crowded Streets. You can watch Dave Matthews Band’s performance on Ellen below:
Guitar pedal multi-effects units comprise several effects in just one package. Multi-effects units utilize digital processing to bring out different sound effects when playing guitar. These digital multi-effects pedals come with internal memory in order to save your individual settings. Among the top-rated multi-effects brands you might want to check out are the DigiTech RP and GNX series, the Boss ME-20 and ME-50 models, the Boss GT-6 and GT-8, the Zoom G2, G3, and G5, various Behringer models, and the Line 6 POD.
A tung oil-finished rock maple neck, and a slightly more curved fretboard radius of 13.75 inches are the other small modifications to the ‘speed’ features on the MD200. However, it has a thinner bolt-on neck as compared to the MD400’s wider mahogany set neck. That said, both neck profiles remain a shallow “C” shape, and the guitars’ dramatically beveled cutaways give you ample room to reach the high notes.

Our first recommendation in this list is the epic Les Paul model by Epiphone. The Special II model of Epiphone is specially made for beginners. If you are just starting to play the guitar and looking for a good quality one from the trusted band, you can buy this one. This one is very low cost and offers a lot more features than other Gibson guitars.
Optocoupling Compressor using a LED and a LDR. Similar to Colorsound Supa Sustain or DOD 280. As others have mentioned, instructions are a single photocopied sheet showing component layout. There's no mention that you'll need a piece of heat shrink to fab up your optocoupler. If you have some experience you can figure it out. Wire was not supplied.
The Squier Vintage Modified Jaguar Bass has major “cool” factor, and the sound holds out, too. With a P-bass style single in the neck position, and a J-bass style single in the bridge position, you’ll actually get the best of both worlds in terms of tonal options on the pickups. You have a choice between basswood (on the sunburst and crimson models) and agathis (on the black model), so there isn’t anything special about the woods they’re using in these basses. But the slim, fast-action, C contour of the maple neck will give you a nice, smooth J-bass feel that plays well above this guitar’s pay grade.
Sometimes a guitar needs more than a setup, and actual repairs are required. Guitar setup price is minimal when compared to the price of most repairs, so be sure that the problem is not something that can be easily adjusted before making any patch-ups. The cost of repairs can be virtually any price depending on the damage. Refinishing might be over $100, and if a neck needs replacement due to warping, then the price may be several hundreds of dollars. A cracked neck can be glued and clamped for under $100, but the quality of the guitar is unlikely to be regained with this process.
Back when they were starting, Jackson guitars were only available to the elite few, mostly heavy metal artists. After being acquired by Fender, Jackson has since expanded into the entry level realm with mass produced versions of their popular guitar designs, including the Dinky shape. The JS11 Dinky does just that, making the Jackson Dinky a beginner and student friendly instrument that more players can enjoy.

I have a Les Paul Gold Top copy I bought new in the mid 70's. It has no brand name anywhere on it. I have done all the research I can and have found no conclusive results.I'm at a loss. It plays great! I do have pics. if that will help. Thanks for any help' It was bought in Montgomery Al. Clarence Carter's guitar player bought one while I was in the store so I figured ...must be a okay guitar. So I bought it. On the little square plate on the back it is hand engraved #0059. Thanks


While many appreciate its bulk of features, there are a few who feel that Fender went overboard, and should've limited the voicings to just a few to ensure that sound quality is not compromised. On the other hand, there are some who felt that the extra features are nice, but they are turned off by the need to use a computer to get full access to all the controls.
Two and a half steps down from standard tuning. Used in Swedish death metal by bands such as At The Gates, Dismember, Edge of Sanity, Entombed, Amon Amarth, and Arch Enemy (during the Johan Liiva era), as well as Fear Factory, Carcass, Type O Negative, Cathedral, Seventh Void, Fleshgod Apocalypse, Sepultura, Five Finger Death Punch, Soulfly, Within Temptation, Triptykon and guitarist Kirk Windstein of Crowbar and Kingdom of Sorrow.
This pedal has been a great start, it has been looked after very well and is in excellent condition. I am upgrading my sound which is the reason for the sale. “Great guitarists know it's all about nuance. With its built-in expression pedal, the Zoom G1Xon allows you to add subtlety and refinement to your performance. Add in 100 great-sounding guitar effects and amp models—with the ability to use ...

Ibanez, a guitar and bass manufacturer, came to prominence as a result of music legends like Steve Vai and Joe Satriani using this brand. These guitars provide an exceptionally uniform neck action, a highly versatile tone, and top of the range pick up configuration. One of the main reasons that this brand gained popularity was the effective tone from cheap and mass-produced instruments. Heavy music is what they excel in, and metal enthusiasts have been loving Ibanez for decades now. They manufacture guitars for every style and genre. The most iconic model is the RG, but S series is also loved by all. They are also the makers of the 7-string guitar, with the first model Universe being made in the year 1990.


The idea behind this site is to share my experience with Do It Yourself approach to guitars, amplifiers and pedals. Whether you want to save a couple of bucks by performing a mod or upgrade yourself instead of paying a tech, or want to build your own piece of gear from scratch, I'm sure you will find something interesting here. Also, this is the home of DIY Layout Creator, a free piece of software for drawing circuit layouts and schematics, written with DIY enthusiasts in mind.
Two more guitars were introduced in 2008. Gibson USA issued the Slash Signature Les Paul Goldtop, modeled after a 1991 Gibson Les Paul Goldtop that was stolen from Slash’s collection in 1999 and never recovered.[37] It features a mahogany body and a hand-carved maple top with Gibson’s classic Bullion Gold finish. Production was limited to 1000.[38] Epiphone introduced a more affordable version of the Gibson model, featuring a traditional Les Paul body with a maple top, a mahogany neck with rosewood fingerboard, and Epiphone’s classic Goldtop finish. Production was limited to 2000.[39]
Replace or upgrade your guitars volume and tone controls with the best quality pots available from CTS, Bourns, Fender, Alpha, Alps and more. From full size to mini pots, long shaft and short shaft pots, blend pots and stacked concentric pots, push/pull pots and more, we have the pot you need! Not sure which pot is right for your project? Then check out the Guitar Electronics FAQ Page for more info on pot values, pot tapers and more.
The numbers back him up. In the past decade, electric guitar sales have plummeted, from about 1.5 million sold annually to just over 1 million. The two biggest companies, Gibson and Fender, are in debt, and a third, PRS Guitars, had to cut staff and expand production of cheaper guitars. In April, Moody’s downgraded Guitar Center, the largest chain retailer, as it faces $1.6 billion in debt. And at Sweetwater.com, the online retailer, a brand-new, interest-free Fender can be had for as little as $8 a month.
pedal bass fender stratocaster electric amp left handed guitar fender telecaster gibson les paul telecaster ibanez epiphone martin guitar fuzz prs taylor guitar gretsch electro acoustic guitar les paul gibson sg marshall stratocaster fender precision bass tokai rickenbacker free fender bass fender jazz bass resonator guitar 12 string guitar fender amp fender jaguar
This list is insanely bad! First of all, John Mayer is only as good as your typical high school amateur. And before anyone starts spouting off, I’ve tried to find some obscure videos of him to prove myself wrong. But I can’t, it’s all Minor Pentatonic stuff with nothing innovative added to it. Secondly, how about some finger pickers on the list: Doyle Dykes, Scotty Anderson, Chet Atkins, Merle Travis, Tommy Emmanuel. Let’s not forget DANNY GATTON the greatest guitar player you’ve never heard. Also, if we’re talking about the best of the best, BRENT MASON should ALWAYS be in a Top Ten list, although he never is. But, you’ve heard him on all sorts of Nashville recordings. Acoustic guitar players like Andy McKee, Ewan Dobson, Don Ross, (I wish I knew more than that but I only recently discovered their Chuck Norris like awesomeness). Never limit yourself to the mainstream! There are many guitar players that are mentioned only because they are famous and have influence because of that. They may come up with a catchy riff or played in a well known band. But, that doesn’t make them a truly great guitar player.
It's like saying the wood handle of a hammer effects the tone generated by hitting a nail. The nails been hit, vibrations through the wood afterward are pointless. Unless the guitar itself is metal and hollow, you would hear sound generated acoustically, as you would with any acoustic instrument. An electric guitar is not an acoustic instrument in a classical sense.
Pitchshifters change the pitch of the note played via a user-specified amount. The range of pitch deviation depends on the equipment used, but many pedals are capable of raising and lowering the pitch two octaves above and below the fundamental pitch. The amount of pitch deviation can be set or controlled via a foot pedal (which typically offers smooth, continuous pitch control). Typically, such function will be used with the original signal, resulting in a Harmonizer: the pitch is altered and combined with the original pitch to create two or more note harmonies. These harmonies are typically programmed in discrete integer multiples of the fundamental tone. When used with an expression pedal, it provides a smooth, abeit slightly digital, bend-like effect. Pitch shifters can also be used to electronically "detune" the instrument. Some examples are:
Hi Timothy, sorry it took a while for me to respond. Yes, from your first statement it sounds like you’ve correctly understood the operation of ‘normal’ guitar pickup selector switches (i.e. standard 3 and 5 position), the wiper contacts overlap as they move across each other. Unfortunately I’ve never seen anything that matches your 4 pick-up idea, if I were you I’d start looking at the 5-position mega switches which have lots of possibilities but can get pretty complicated. Good luck!
The extra-versatile twin-channel layout with independent controls delivers a wide variety of tones from clean to overdrive. The Sonzera 20—which we recently reviewed—packs a hell of a punch for players who need a versatile workhorse amp that pairs well with pedals and sounds incredible on its own for any style of music. While the Sonzera 50 Combo is well suited to the stage, the 20 is easy to haul to gigs, has a lower output that’s better suited for the studio—and its “American style” voicing thanks to its 6L6 power tubes (the Sonzera 50 features EL34 tubes).
Wah pedals can sound eerily similar to a human voice, and they were actually a favorite of Jimi Hendrix, who many have said possessed the most expressive guitar playing amongst all the great guitarists. Wah pedals are great to activate right when you’re about to take a solo and when you really want to make it sound like you’re speaking with the guitar.

Description: Body: Basswood (Tilia, Linden, Lime) - Body Construction: Solid - Neck Attachment: Bolt - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 24 - Inlay: Pearl - Dot - # of Strings: 6 - Bridge: Double Locking - Cutaway: Double - Hardware: Black, 5-Way Switch - Pickups: Alnico Humbucker - String Instrument Finish: Pearl White, Pearl Black
{"eVar4":"vintage: guitars","eVar5":"vintage: guitars: electric guitars","pageName":"[gc] vintage: guitars: electric guitars: lyle","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop2":"[gc] vintage: guitars: electric guitars","prop1":"[gc] vintage: guitars","evar51":"default: united states","prop10":"brands","prop11":"rickenbacker","prop5":"[gc] vintage: guitars: electric guitars","prop6":"[gc] vintage: guitars: electric guitars","prop3":"[gc] vintage: guitars: electric guitars","prop4":"[gc] vintage: guitars: electric guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] vintage"}
Tags: 335 harness 335 wiring harness ES335 harness Firebird Harness Gibson Firebird Harness Guitar wiring Guitar wiring boards Guitar Wiring Harness Guitar Wiring Harness UK Guitar Wiring Harnesses Guitar Wiring Harnesses UK Guitar wiring loom Handwired Harness Home of Tone Home of Tone Blog Home of Tone harness Home of Tone Harnesses Home of Tone pre-Wired Les Paul Harness Les Paul Harnesses Pre-Wire Harness Pre-Wired Guitar harnesses Pre-Wired Harness Pre-Wired harness UK Pre-Wired Harnesses Pre-Wired Home of Tone harnesses Sg Harness Strat Harness Stratocaster Harness Stratocaster Harnesses Tele Harness telecaster Harness
{ "thumbImageID": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "defaultDisplayName": "Gibson Les Paul Faded 2018 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Worn Cherry Black Pickguard", "sku": "sku:site51500000137380", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard-1500000137380.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001-00-60x60.jpg", "imgAlt": "" } , { "name": "Worn Bourbon Black Pickguard", "sku": "sku:site51500000137381", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard-1500000137381.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001-00-60x60.jpg", "imgAlt": "" } ] }
Buddy Holly turned a generation of future heroes – George Harrison, Eric Clapton, Jeff Beck – onto the guitar, with an elemental style: an antsy mix of country and blues that merged rhythm and lead; check the push-and-tease phrasing on "It's So Easy," which echoes Holly's growl-and-hiccup vocals. Playing his Stratocaster and fronting a double-guitar-bass-and-drum quartet, Holly essentially invented the rock band. "Listen to the songs on the first three Beatles albums," says John Mellencamp. "Take their voices off and it's Buddy Holly."
Sound quality-wise, it’s too close to call. All modern Zoom, Line 6, Boss, and DigiTech multi-effects units sound excellent. Distortion sounds a bit better on the DigiTech, and if reverb is your thing it doesn’t get much better than the Lexicon verbs. The other multi-effects units might be better if you’re looking for more experimental sounds and textures. The DigiTech RP500 tends to be more conservative, and focuses on nailing the classics.
• How to check frets: The easiest and quickest way to make sure a guitar’s frets are in good shape is to look straight down the neck of a guitar, from body to headstock. If the frets are at different heights (improper installation is the culprit here with new guitars) or askew, there are problems. They should look uniform and exhibit as little denting or wear as tolerable. 
Gibson produced only hollow body electrics until 1952, when the first Les Paul solid bodies hit the market. But that still left a gap. Certain players wanted a guitar with the versatility of a Les Paul, but the warmer, mellow tone of a hollow body — albeit one that could be played at high volume. A solid wood block runs through the center of the guitar’s body, allowing greater sustain and less feedback at high volumes than hollow bodies, while the winged side of these guitars’ bodies still provide for a mellow tone thanks to their acoustic resonance.
Five string guitars are common in Brazil, where they are known as guitarra baiana and are typically tuned in 5ths. Schecter Guitar Research produced a production model 5 string guitar called the Celloblaster in 1998.[43] A five-string tuning may be necessary in a pinch when a string breaks on a standard six-string (usually the high E) and no replacement is immediately available.
Here we have a Faithful Recreation of the classic Martin D-18 that was well crafted in Japan over 33 years ago. This is an excellent vintage Japanese guitar as it has been well taken care of all these years And has spent its years in California in the perfect climate to preserve the guitars original structural and cosmetic integrity its fit and finish to this day is still JVG rated at very good to excellent with no cracks or finish checking none – clean and still shines like glass….. its 1-11/16ths at the nut neck is a nice comfortable medium slim profile, neck is straight with correct amount of slight relief, action is good medium low and plays with ease and sound is clear and volume is good, tone is vintage sweet from its Aged tone woods. This is a true Lawsuit model as it has the direct image shape & size of the vintage Martin it copies is is a very cool D-18 guitar, its 33 years it’s obviously not new or mint but is surely vintage beautiful with its age and genuine warmth & patina and yes a few minor doinks but nothing to detract from its overall appeal. .

The really important player on the scene today in the low end and intermediate price bracket is Mainland China. Whereas Yamaha and other makers have produced guitars in Taiwan for quite some time, Mainland Chinese guitars were always noted as being of extremely low quality. In the past few years, however, that situation has changed dramatically. In the past ten years, China has moved rapidly toward entrepreneurial private ownership of business. The new leadership has pushed this process quickly. China now permits foreign ownership of factories and businesses as well as encouraging Chinese citizens both from Mainland China and Taiwan to set up their own ventures. Just as the Koreans were able to progress from very low-end student models with crude workmanship to remarkably sophisticated guitars more quickly than the Japanese had, the Chinese now have all the advantages of the prior experience of Americans, Japanese, Korean and Indonesian ventures. In addition it should be noted that while Chinese labor is remarkably inexpensive, with an average annual income in China today of under $1,000, Chinese labor is by no means unskilled. China has a very high literacy rate and its workers are skilled and motivated. In the past the world has had areas with cheap labor and other areas with skilled labor. China is a major force to reckon with because it offers cheap skilled labor. The Chinese today are producing instruments in many different settings, ranging from small workshops specializing in handcrafted instruments on up to huge industrial complexes with the latest automated technology. Only ten years ago Chinese-made violins were viewed as almost a joke. They were violin-shaped objects but certainly did not play or sound like one. Today we at Gruhn Guitars are selling beautifully crafted Chinese violins made with excellent wood and superb craftsmanship at very reasonable prices. Some of these instruments compare very favorably with European and American violins costing thousands of dollars. Gibson has set up a factory in China to produce Epiphone guitars and numerous American makers, both large and small, are having guitars, banjos and mandolins made there. Whereas it would be prohibitively expensive to make guitars or other instruments in Japan today using techniques similar to those employed by Martin and Gibson in the 1930s with assembly line production but still featuring a high degree of hand craftsmanship and human judgment, in China today it is economically emminently feasible to do so. The violins we import are beautifully crafted and even feature genuine varnish finish for a very small fraction of the cost that companies such as Gibson charge simply for the option of a varnish finish on one of their standard models. The Chinese are very rapidly taking over the student- and intermediate-grade markets. Not only do they produce fretted instruments, but they have taken over a large segment of the piano market as well as producing wind instruments. I have seen and played prototype acoustic Chinese instruments which rival American-made guitars by some of the same American manufacturers bringing in these imports. It will be most interesting to see how this develops.
{ "thumbImageID": "Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000", "defaultDisplayName": "Fender Special Edition Deluxe PJ Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Olympic White", "sku": "sku:site51500000048792", "price": "899.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-Olympic-White-1500000048792.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-Olympic-White/H96715000004000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-Olympic-White/H96715000004000-00-60x60.jpg", "imgAlt": "" } , { "name": "3-Tone Sunburst Maple", "sku": "sku:site51434378852529", "price": "899.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple-1434378852529.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple/H96715000003006", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple/H96715000003006-00-60x60.jpg", "imgAlt": "" } , { "name": "Sea Foam Pearl", "sku": "sku:site51365435327256", "price": "699.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl-1365435327256.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000", "brandName": "Fender", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000-00-60x60.jpg", "imgAlt": "" } ] }
Ibanez 12 string Martin style, vintage Natural High Quality Japanese Ibanez Vintage Guitar ....This example is MODEL# V302 ...And it IS ANOTHER great find this one is in a Natural finish and is a REAL GEM ta-boot and it has a Beautiful aged Premium Solid German Sitka Spruce Top, WoW! what a nice glass like original finish to this one ...again High Grade woods used on this 80's Ibanez AAA Mahogany Sides-Neck & Back "see quality og the grain in the pics" . Lots of volume & is full-and rich tone from this baby.Pics show missing string done while we were cleaning her up they just snapped ... obviously old and so this guitar will come with a brand new set of Martin strings installed for the new owner no worries..... this one is ez to play & stays in tune well. It is a crafted in Japan guitar and it compares favorably to Gibson, Guild or Martin... at a fraction of that cost. Note: we also have a Sunburst V302 in stock in our listings please see that if you prefer the guitar in sunburst. Thank you for your interest, Joe.
The electric bass was invented in the 1930s, but the instrument did not sell well until Leo Fender developed the Precision Bass in the 1950s. As such, the type of bass players who first began trying methods to make their instruments louder with amplifiers and speakers were upright bass players. While the upright bass is a large instrument, standing about six feet tall (with its endpin extended), due to its low register, it is not a loud instrument when played acoustically. This is largely a result of the decreased sensitivity of human hearing, which is most sensitive to mid-range tones; equal perceived loudness for a mid-range sound and a low frequency sound requires much more acoustic power in the low-frequency sound. In the 1890s and early 1900s, upright bass players performing in bars and brothels in an era before amplifiers and speakers were available, particularly those who performed in bands with louder instruments such as trumpet, often found it hard to be heard. About the only solution available in the pre-amplifiers era was playing slap bass, a style of slapping the strings against the fingerboard to make a relatively loud percussive sound. Beginning in the 1920s, the first amplifiers and speakers designed for gigging musicians became available.
While pretty much every noise musician uses the guitar as a weapon of mass destruction, Mark Morgan of scuzz-worshippers Sightings uses his guitar for sheer negation. Playing in 50 shades of gray on found and borrowed pedals, the leader of this longtime Brooklyn noise band is quicker to sound like a vacuum humming, toilet flushing, or scrambled cable porn feed than Eric Clapton or even Thurston Moore; a unique sound that has all the emotion of punk, with none of its recognizable sounds. As he told the blog Thee Outernet: “Probably the biggest influences on my playing style is sheer f—king laziness and to a slightly lesser degree, a certain level of retardation in grasping basic guitar technique.”
Jump up ^ "The first incontrovertible evidence of five-course instruments can be found in Miguel Fuenllana's Orphenica Lyre of 1554, which contains music for a vihuela de cinco ordenes. In the following year Juan Bermudo wrote in his Declaracion de Instrumentos Musicales: "We have seen a guitar in Spain with five courses of strings." Bermudo later mentions in the same book that "Guitars usually have four strings," which implies that the five-course guitar was of comparatively recent origin, and still something of an oddity". Tom and Mary Anne Evans Guitars: From the Renaissance to Rock. Paddington Press Ltd 1977 p.24
I was interested in this book, and almost walked away after reading many negative reviews which complained about black and white photos and numerous typos. Then I noticed it was available in a Kindle version, for only $9.99. I ordered the Kindle version, and have no regrets. I have read it on my iPad, and gleaned a lot of useful information from it. I have not encountered any typos, and the colored wiring diagrams and numerous photos are just fine. It seems that the paperback version suffered from a poor layout and printing job, which is a shame, since it is obvious to me that Mr. Swike put in the effort to make a good product, which the Kindle version surely is. Anyone interested in a simple but comprehensive intro to wiring their Strat/Tele/Les Paul will find this a good reference. I also enjoyed the Varitone circuit presentation, and the explanation of how capacitor values affect treble/bass response.
In this example I used the "Sub Engineer Bass" patch included in the Kontakt 5 bass collection. But there are no rules in this regard: a simple sine oscillator can do the trick just fine. Back in the '60s and '70s it was not unusual to use a Rhodes to achieve the same effect, and Roland's famous JUNO-106 was also used on countless occasions with the same goal in the '80s. Just give it a go with whatever you have at hand!
“You can also think of it as what the signal path in a studio situation would be if you were to plug your guitar directly into the input of your amplifier, and process that sound through outboard effects. You’re not going to have your echo first before going into your distortion boxes—unless you’re looking for a specific sound—because you want the echoes to die out naturally, and not with your distorted sound.”
Sound images are very similar to visual images. If you're in a large auditorium, but standing on stage right next to an actor's face, you will see every nuance of his face, pimples, pores and all. You will not see his whole body though, and you won't see him in the context of the rest of the stage or the room. If you move back to the tenth row, you will lose some of the facial detail, but you will gain perspective. If you move to the rear of the auditorium you'll lose all the detail of the actor's face, but you see the whole enchilada in perspective.
By the late 1960s, as electric guitarists in rock bands began using powerful, loud guitar stacks to play large venues, bassists needed a large, powerful bass stack to keep up in these performance settings.[3] The Acoustic 360 was a "200-watt, solid state head designed to drive the 361 cabinet, a rear-firing 18” speaker enclosure".[3] The engineers who designed the amp and cabinet in 1967, Harvey Gerst and Russ Allee, mounted the 18" speaker in a folded horn enclosure; the 360 amp had a built-in fuzz bass effects unit.[4] The Acoustic 360 and its 361 cabinet "...got the bass world ready for the Woodstocks, Altamonts and giant festival concerts" and it was used by notable players such as funk bassist Larry Graham, Led Zeppelin's bassist John Paul Jones and jazz fusion player Jaco Pastorius.[3] John Paul Jones used two of the amp/cabs in Led Zeppelin; Dave Brown used them with Santana; John McVie played with the amp/cab in the beginning years of Fleetwood Mac.[4] In December 1967, the loud sound of the Acoustic 360 led to The Doors getting "...arrested for noise violations".
Bass amplifier equipment manufacturers include a variety of different types of companies, ranging from companies that only make individual components (e.g., Accugroove loudpeakers, a speaker manufacturer) to companies that only make bass amplifiers and loudspeakers (e.g., Gallien-Krueger). At the other end of the spectrum are companies that offer bass amplification equipment as part of a much broader offering of different types of instrument amplifiers and public address systems (e.g., Peavey, Carvin A&I or Yorkville Sound.)
Bold and brash, the chest-thumping sound of Fender's big-bodied California Series Redondo Player acoustic-electric was designed to inspire you from the moment you pick it up. The exclusive slope-shouldered Redondo body shape has a rich, commanding voice that fills any room. The gloss metallic top, back and sides, as well as a matching painted 6-in-line headstock and creme binding, give it a shot of electrifying attitude. Dynamic, unique and unconventional—like today’s guitarists—the Redondo Player refuses to be bound by the past.
Description: Body: Mahogany - Body Construction: Solid - Neck Attachment: Set - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Inlay: Custom - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black - Pickups: Ibanez - String Instrument Finish: Satin Oil, Transparent Black Sunburst
Number of Effects: All multi-effects units have a number of effects to choose from; that’s the entire point of them! However, make sure the pedal you go with has plenty of selection that will meet your needs. Typically, the more effects there are to choose from, the better. Chances are over time you’ll narrow the selection down to a few of your favorite ones. The top 5 multi-effects pedals on this list all have plenty of effects to choose from (the lowest has around 40, and a few have 100s).
This has always been one of the most revered brands of guitars amongst professional musicians. They sell one of the most affordable and durable electric guitars. The acoustic and classic guitars sold by this brand are ideal for students and beginners. The dreadnought sized body with cutaway has a Sitka spruce top with nato back & sides. The neck has 20 frets & dot inlays on the fretboard and made of nato. The bridge and fingerboard are made of rosewood. Yamaha’s own System55T. The starting price of a Yamaha acoustic 6-string guitar is 6990 INR.approximately.
{ "thumbImageID": "Limited-Edition-SG-Special-I-Electric-Guitar-Cherry/J38676000003000", "defaultDisplayName": "Epiphone Limited Edition SG Special-I Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Cherry", "sku": "sku:site51500000013041", "price": "174.99", "regularPrice": "174.99", "msrpPrice": "248.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Limited-Edition-SG-Special-I-Electric-Guitar-Cherry-1500000013041.gc", "skuImageId": "Limited-Edition-SG-Special-I-Electric-Guitar-Cherry/J38676000003000", "brandName": "Epiphone", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Limited-Edition-SG-Special-I-Electric-Guitar-Cherry/J38676000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Ebony", "sku": "sku:site51500000013039", "price": "174.99", "regularPrice": "174.99", "msrpPrice": "248.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Limited-Edition-SG-Special-I-Electric-Guitar-Ebony-1500000013039.gc", "skuImageId": "Limited-Edition-SG-Special-I-Electric-Guitar-Ebony/J38676000002000", "brandName": "Epiphone", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Limited-Edition-SG-Special-I-Electric-Guitar-Ebony/J38676000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Pelham Blue", "sku": "sku:site51500000013040", "price": "174.99", "regularPrice": "174.99", "msrpPrice": "248.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Limited-Edition-SG-Special-I-Electric-Guitar-Pelham-Blue-1500000013040.gc", "skuImageId": "Limited-Edition-SG-Special-I-Electric-Guitar-Pelham-Blue/J38676000001000", "brandName": "Epiphone", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Limited-Edition-SG-Special-I-Electric-Guitar-Pelham-Blue/J38676000001000-00-60x60.jpg", "imgAlt": "" } ] }
I recommend you buy your pickup new, and from a place that you trust. I am getting more and more unsatisfied with Musician's Friend(everything I order is backordered...) so after being informed that my pickup was going to be in stock three weeks from when I wanted it, I canceled the order, bought the same pickup at Guitar Center(online) and it came in by the end of the week.
Slash is a longtime fan of legend Seymour Duncan’s hand-wound pickups, and for his new Epiphone Firebird, Slash choose custom Seymour Duncan "Slash" open coil-humbuckers for the rhythm (APH-1) and the lead positions (APH-2). These were Slash’s first custom pickups made with Seymour Duncan and feature Alnico II magnets and are slightly overwound for a boosted output. Each pickup has a single conductor cable, a long-legged bottom plate, and a wooden spacer. Controls include individual Volume and Tone pots with traditional Black Top Hat knobs with metal inserts and pointers along with a Switchcraft 3-way Toggle switch. Tone controls for both pickups also feature Sprague "Orange Drop" capacitors (0.022uF, 600V, 5%), the same capacitors Slash uses on his custom designed Les Pauls.

The #1 cause of fret wear is the fretting hand pressure exerted by the player.  I have some clients that grip very tightly and wear frets quickly (Rob Fahey), and some that grip very lightly and take forever to exhibit significant wear (Jasan Stepp, Dog Fashion Disco/PolkaDot Cadaver).  Fret material hardness, string hardness and frequency of use all contribute to wear as well, but hand pressure is still the leading cause since frets do not wear themselves out.  Technique is different for every player, unique and personal and habits can be hard to change.  Just like brakes in a car, how hard and how much something is driven directly impacts wear and longevity.  Please see the refrets page for further thoughts on this topic.

The key feature that makes the GT-1000 stand out from the crowd is the inclusion of the ingenious AIRD (Augmented Impulse Response Dynamics) technology which ensures your effects respond correctly with the likes of tube amps and don’t muddy your sound. You can read more about the AIRD technology here, but in a nutshell, it ensures the dynamics of your unique amp are preserved. With other multi effects, you might find have to turn your amp emulations off if you want your effects to respond correctly to YOUR amp, but with the GT-1000 you won’t have to do that as you can select which type of amp you’re playing with and the pedal will respond correctly.

I will not take my guitars anywhere else. You just do not get better, more professional service than at Franklin Guitar. I have played guitar for a long time and I have been in hundreds of guitar stores, and this is one of the best. You won't get the "hey don't touch that" or they "what's it going to take to get you into one of those guitars?" treatment. You get treated like a valued customer. Also a lot (most) of independent guitar stores have terrible assortments of guitars for sale, but not Franklin Guitars. They have a great variety of quality instruments. Plus, they have some really cool, unique guitars. A place like this is so rare nowadays.


A tremolo pedal takes your signal and chops it up, making it sound like the volume is dropping and reappearing very quickly. Imagine what it would sound like whilst holding a note and turning the volume down on your amp and back up again and you’ll get the idea. A tremolo allows you to change the speed at which the volume drops happen and how severe the cut off is. You can have it set to completely cut your sound out or just gate it, which allows a certain amount of sound through at each interval. The BOSS TR2 Tremolo is one of our favourites here at PMT.
It’s hard to conceive a better musical foil for Steven Tyler than his longtime partner and occasional adversary. For more than 40 years, Joe Perry’s monstrous, blues-on-steroids riffs have been Aerosmith‘s bedrock. And his solos, jutting out from “Walk This Way” or slashing boldly through the high-gloss production of later hits like “Janie’s Got a Gun” and “Cryin’,” have a caffeinated energy that’s every bit Tyler’s match. “He had a streamlined style that reminded me of Keith Richards,” said Slash. “And a careless style that’s really cool.”
The semi-hollow guitar is based on having a “tone block” that runs down the center of the body of the instrument.  This reduces feedback issues while still maintaining the woody tone of the true hollow body instruments that are widely used in Jazz.  This allowed the pickups to be mounted to a solid block, while the outer portions of the instrument are hollow, which are often adorned with “f-holes” much like instruments of the Violin family.  This type of build provides the resonance and tone of fully hollow instruments, while providing a resistance to feedback that allows the guitar and amplifiers to be used at a higher volume.
In the earlier days of My Chemical Romance, Iero mainly used Gibson SG's & Epiphone Les Paul guitars (most notably his white Les Paul nicknamed 'Pansy' which proved popular amongst his fans but has since been broken while onstage) and Marshall amps. He has since switched to using Gibson Les Pauls (with the Neck Pick-up removed) and occasionally uses a Gibson SG. He also used a Fender Stratocaster in the Desolation Row video. He has recently collaborated with Epiphone to design the Wilshire Phant-O-Matic guitar which he used onstage for the My Chemical Romance 'World Contamination' Tour, the Honda Civic Tour and for the Reading and Leeds festivals.
Rock On Good People (it’s actually rockongoodpeople) is another YouTube channel really designed to funnel viewers towards the creator’s website, www.nextlevelguitar.com which—no surprise—has heaps of stuff you can buy. But that doesn’t mean that Rock On Good People doesn’t provide a long list of free videos ranging from lessons for beginners through to how-to-play-techniques aimed at experienced players. What I like about Rock On Good People is the cool vibe you get from all the presenters, no matter the style or subject of the lesson, and some of the videos take you further down the guitar-playing track with themes like “Tips For Improving Your Live Shows”. That might seem a long way off, when you’re currently trying to get your head around playing basic barre chords, but these videos have hints and advice that are good seeds to plant in your mind early, even if you’re still some years off jumping off your first Marshall stack and into the mosh pit.
Once CNC (computer numeric control) equipment was introduced into guitar factories starting in the late 1980s and continuing on into the 1990s, it became far less of an issue where a guitar was made. Many of the CNC machines were made in Japan. In some cases the difference between an American-made guitar versus a Japanese-made guitar versus a Korean-made guitar was little more than where the machine was located. To make a guitar in the USA involved putting a Japanese-made CNC machine on a boat and sending it to the US whereupon it could be programmed in the USA and then American or other wood could be fed into the machine, which would spit out components made to tolerances within a few thousandths of an inch of the programming. By contrast a Japanese-made guitar would be produced by leaving the CNC machine in Japan, programming it with a disc done in the USA, and then importing wood to be put into the machine which would spit out components to the same specifications as those which would be made by a similar machine in the USA. A Korean-made guitar could be remarkably similar since the Japanese-made CNC machine could be sent to Korea whereupon the same process could be done there. By 1990 the quantity of guitars made in Japan was nowhere near what it had been earlier, but Korean production was in high gear. While some Japanese instruments have come to be viewed as quite desirable and collectible, I have seen little evidence of such activity with respect to Korean instruments, but the fact remains that the better-quality Korean guitars are remarkably good and most certainly are suitable for use on stage or in the studio.
Yet you’d never find a punk rocker who didn’t want to be just like him. Whereas most punk guitarists found inspiration from the same hard rock and proto-metal players that they pretended to despise, Strummer was influenced by reggae, rockabilly, soul, ska and even early New York rap music when most of the world still hadn’t heard of the Sugarhill Gang.
×