These prices reflect the opinion/perception of the editor of while these are prices one could expect from a quality repair shop, repair rates can vary. A full time repairman can have as much training time and investment in tools as any mechanic. Shop overhead costs are on par with those of any other profession, so if you take your instrument to a professional shop, expect to pay professional rates. And expect professional work. While this list reflects prices one would expect to pay at a professional shop, rates will vary. Expect to pay by the hour for some extensive restoration jobs. Rates based on an hourly charge of $60.00 p/hour. Shop minimum labor charge - $60.00 Prices updated January 2014

The pedal rocks forward and backward like a see-saw as you rest your foot on it. Move the pedal to get the wah effect. On some pedals, there is a switch under the toe end to switch ceon straight-through (no effect) to using the wah effect. This means that when you switch it on, it's always in the "aaaa" position. You can hear this in some of Hendrix's work.
Tonhöhe ebenfalls gehoben und kann auf die gewünschte Tonlage eingestellt werden. Der Ibanez DOWNSHIFTER erlaubt es, die Tonlage einer Saite durch einfache Hebelbetätigung auf eine vorgegebene gewünschte Position zu senken. Um präzises Tuning für sowohl Auf- und Ab-Positionen zu erzielen, müssen Sie beide Hebeleinstellungen vor Betätigung des Downshifters voreinstellen.
For someone who’s been playing for a while, your options are a little different. Perhaps they’ve got a certain guitar in mind. If so, get them what they want! Chances are they’ve already done their homework and have their eye on their next guitar. If they’re not sure, you can still make an educated purchase. There are many popular options that should satisfy most experienced players. And there are many lesser-known models that can be the right fit for someone with more specific tastes.
Likewise, the two coils of a humbucker which are wired in series can be connected in parallel. This results in a brighter sound and lower output resembling that of a single-coil pickup. Compared to coil split the sound is usually a bit fuller and the pickup's hum-cancelling properties are retained. Like coil split, wiring a humbucker in parallel requires the start and end of both coils to be accessible, which is sometimes possible with stock pickups. Unlike coil split, it also requires a DPDT switch (coil split only requires a SPDT switch).[26][28]
Amazing unit! I loved using my POD XT Live for years and wanted to upgrade. This unit totally exceeded my expectations. Sounds amazing and it's incredibly flexible for routing processing and effects chains. They built the hardware better and it's got a better set of pedal buttons too. Absolutely recommend! (Plus, they announced at NAMM that there will be more model packs, so that's great too!)
Electro-acoustic guitars are commonly referred to as semi-acoustic guitars. Electro-acoustic guitars have pickups that are specifically designed to reproduce the subtle nuances of the acoustic guitar timbre. Electro-acoustic pickups are designed to sound neutral with little alteration to the acoustic tone. The Ovation range of Electro-acoustic guitars have under-the-saddle piezo pickups and a synthetic bowl-back design. The synthetic bowl-back ensures a tough construction that stands up to the rigours of the road while offering less feedback at high volumes. Ovation were the first company to provide on-board Equalization and this is now a standard feature. The Taylor Electro-acoustic range uses the traditional all-wood construction and the necks of these guitars have a reputation for superb action and playability. Yamaha, Maton and many other companies manufacture Electro-acoustic guitars and the buyer is advised to test as many models and makes as they can while taking note of the unplugged and amplified sound.
This is breathtaking and very inspiring pop-rock music with great energy and bright motivational atmosphere. Main instruments are electric guitar, digital synth, bass, strings, piano and drums. This exciting and uplifting track could be a perfect choice as background music for any video production, multimedia projects, Youtube channels, narrations or life stories, films and other projects.

The stringed, chord-playing rhythm can be heard in groups which included military band-style instruments such as brass, saxes, clarinets, and drums, such as early jazz groups. As the acoustic guitar became a more popular instrument in the early 20th century, guitar-makers began building louder guitars which would be useful in a wider range of settings.

I have had some truly “nightmare” scenarios with repair people in my time, and you must beware of these folks who love to take your money, but who can totally botch a repair job on a nice guitar! It’s happened often enough to me to make me be very careful whenever I am “trying out” a new repair shop for guitar-related problems. Due to this, I often like to start with bringing them some relatively un-complicated guitar repair problems such as fret jobs and wiring problems, but even these have sometimes turned into nightmares. Today for example, I brought of all things, 3 Lap Steels and one semi-hollow guitar for repairs, but unfortunately the store’s repair guy was not there. We had a good communication though, and they made sure I wrote down the repairs I felt were needed, with a separate sheet for each instrument, and said that he’d be calling me with any questions regarding the guitars and their repairs before tearing into them!
Position 2 (outside coils, parallel connection): this one is more exciting because all poles do something. Pole 1 connects bridge pickup coil tap to ground, effectively splitting the bridge pickup. Pole 2 connects bridge pickup hot lead to the output. Pole 3 connects neck pickup coil tap to pole 4 which connects it to the output. What we end up with is a coil from bridge pickup coil tap to hot lead and a coil from neck pickup ground to the coil tap. Because of the way poles 2 and 4 are connected, these two coils will be paralleled.
The Epiphone Company is a musical instrument company which was founded in the year 1873. Epiphone is specialized in making Guitars and are one of the largest producers of guitars in the world. Epiphone has several ranges to choose from, as they brand them in different groups. Few of the Epiphone ranges of guitars are, Epiphone Sheraton, Epiphone Casino, Epiphone Texan and The Dot etc. Besides guitars Epiphone also manufactured upright basses, banjos and other forms of stringed instruments.

Fender has shown the spec sheets of its popular Mexican-built Deluxe Series Roadhouse Stratocaster model some love to create a reboot that comes seriously well appointed. The upgraded model features an alder body and bolt-on maple neck, with the option of maple and rosewood fingerboard, finished with satin polyurethane. Keep sniffing around and you'll find other features like the 'Modern C' neck profile, 22 narrow/tall frets, a contoured neck heel, synthetic bone top nut and a set of locking tuners with vintage-look buttons. While the previous editions of the Roadhouse and came with a 241mm (9.5-inch) fingerboard radius, the new model packs a flatter 305mm (12-inch) camber. Yes, the same radius as a Gibson Les Paul, making for easier string bends and lower action. The new Roadhouse features three Vintage Noiseless (1st generation) single coil-sized humbuckers wired to a five-way pickup selector blade switch, and master volume and tone controls. Lurking between the volume and tone knobs is the V6 preamp control, a six-position rotary switch that gives you access to a series of tweaked single-coil tones. Plugging in the Roadhouse reveals a slew of classic Strat tones. The pickups exploit the natural tone and woodiness of the guitar, while the Noiseless aspect lives up to their vow of silence, making them indispensable in a recording situation. As a result, bar metal, this is the best Fender electric guitar for just about all scenarios.
Barely used in my home, NUX Cerberus multi pedal. Not a modeler, it has true bypass distortion, overdrive, modulations(chorus,flange, phase, univibe and trem) as well as delay and reverb- all completely programmable and can be used as a pedal board or as presets. Built in tuner and cab simulator- great multi pedal can be used as a fly rig or in front of an amp- Comes in the original packaging with power supply. US buyers ONLY- I will not ship internationally- No returns accepted
Actually it was a rolling stone interview, I don’t remember the exact issue but the reply was Rory Gallagher. I’ve also heard it was Phil Keaggy which is unlikely because he was relatively unknown when Hendrix was alive. I’ve also heard it was Terry Kath, Billy Gibbons, and Eric Clapton. I do know that Hendrix said his favorite guitar player was Gibbons, because he just couldn’t get that sound that Billy gets. As for the Quote……. maybe it’s just folklore… The most likely correct answer is Rory Gallagher though…. it’s even referred to in Rory Gallaghers biography and the actual issue of the rolling stone interview is listed in there. I’ve never heard anyone say that the quote was with Jerry Reed though. But, Jerry Reed is an AMAZING guitar player. He actually wrote alot of Chet Atkins material. As for misquoting Hendrix you may not want to be so quick to point fingers…. I’m pretty sure yours is wrong. 😉
Chicago’s vintage guitar shop is located in Ravenswood just west of Lincoln Square. Rock N Roll Vintage is your one stop shop in Chicago for new guitars, vintage guitars, Chicago guitar lessons, guitar pedals, and we are currently the largest synth dealer in the Midwest. Looking for a specific guitar? Rock N Roll Vintage Guitar Shop carries Fender, Gibson, Martin, Gretsch, Rickenbacker and other popular guitars and basses including boutique amps. We have one of the largest selections of effects pedals in Chicago with many hard to find boutique pedal brands.
Another LTD model that is easily on the same level as the standard ESP stuff is the MH-100QMNT. The guitar comes from the very top of LTD’s entry level lineup, and brings a great price to performance ratio. I’ve had a lot of time to play with this guitar, and at first it didn’t sit right with me. As I played it more, I got used to the contour of the neck and the way its body ‘moves’. From that point on, ESP LTD MH-100QMNT grew on me rather quickly.
The RP360 XP lets you combine different effects to craft your preferred sound by choosing from its wide variety of options including 74 effects, 32 amp models and 18 cabinet models. Each setup can be saved into one of its 99 user presets, that allow for incredible flexibility. The interface has a bit of a learning curve, but allows for deep editing.
Excellent condition Traveling Wilbury's solid body electric guitar. Each Gretsch TW-100T is unique in it's graphics. Featuring a solid maple neck and an ebony colored finger board w/ dot inlays and no fret wear. Fully adjustable "Strat-style" tremolo / bridge including whammy bar. One single coil pickup and a volume control. Only the most minor of wear to the finish.

I finally had the chance to bring my les paul for Steve to look at an annoying fret buzz. First he said the guitar is too straight and adjusted it. Then he quickly discovered the 4th string buzz was at the first fret but it had nothing to do with the buzz because the issue was at the nut, it was cut too low! Steve redo the string while we were chatting about how the neighborhood has changed. Within 5 mins, Steve redo the with some filling and filing and voila!! The buzz was gone. I was so happy and asked him how much, he said it was easy so he didn't want take any money. But i have him some coffee money and he said it was too much, I said it was for a week and he laughed. My last issue I brought to Steve as well and we had the same conversation. I highly recommend Steve as experienced luthier and for someone who loves guitars and someone who can solve guitar problems. Steve is a hidden gem in the Boston guitar world.
   I am now building several models which I offer as my signature work. I've always had a special affinity for archtop guitars, but as you'll see in this website, I will go wherever the creative impulse takes me. The instruments I am building now are a distillation of the best design ideas I've found in classic instruments, re-imagined and evolved into higher form and function, as fine tools for discerning artists. 

Vocal Widening: One of the send effects I most frequently use at mixdown has got to be the classic vocal-widening patch that I always associate with the vintage AMS DMX1580 delay unit. From a mono send a stereo ADT-style effect is created using two pitch-shifting delay lines, panned hard left and right. Normally, I set the first channel to 9ms delay, with a pitch shift of -5 cents, and the other channel to an 11ms delay, with +5 cents of pitch shift. That said, though, I will often tweak the delay times a few milliseconds either way, as this can dramatically alter the effect's tonality. Mike Senior

i really liked it! especially since it goes over standard musical notation, which hasn't been considered a conerstone for electric guitar players, but i think, like the author says "it a skill you'll never regret learning". the reason it didn't get 5 stars is because the book states that it will start from zero as for standard musical notation, but it doesn't, it assumes a bit of knowledge and it advances at a perfect rate for some who has already a notion of standard musical notation, but not for someone who doesn't have a clue a buys this book to go from zero-to-master such ability.
While you're doing your strumming and picking lay that part of your hand on the strings by the bridge of your guitar. This will mute or partially silence the strings. On an electric guitar going through an amp, this can become a percussion instrument. The trick is to use it for a percussion effect and then raise that hand up when you want to let the strings rings er.. ring.
Which brings us to this 1985 DT-250. While it sports the tail notch, the shape is a little more sleek and diminutive than the comparable Dean ML. The lower front bout is extended to be almost symmetrical with the diagonally opposite bass wing. The treble-side lower bout is shortened, giving the whole guitar a tasteful offset-X shape… X Series. To add dimension to the shape, Fuji Gen Gakki added “crystal cuts” to the edges, basically code for angled bevels.
After a certain point of decreasing the price on the amplifier systems you are offering to the buyers, you get a return in the shape of an increasing size of the amplifiers themselves. Which is not really that much of a problem, especially when the Fender speaking you are talking about look vintage and sounds like it could be from the future. The Fender Mini Tonemaster Battery Powered Electric guitar amp is a little on the big side among smaller amps, in terms of size and in terms of sound. While it might be a little tiring to carry with you, the sound you are going to produce for the price of almost nothing is going to feel worth it, every second of the song.
These are world class guitars and have got probably the best feel any guitar can give apart from that u can play everything on these guitars from classic rock to jazz and blues followed by metal. the main thing that these guitars are known for is their finish and there unique necks which are really fast and not too thin which keeps your tone and feel in place. I would say that these guitars definitely deserve a place in the top 3 and definitely do watch out for the petrucci signature models
The guitar starts off with a basswood body, carved into the familiar Stratocaster double cutaway. Even the pickguard resembles that of a Strat, although the controls are different, with the Adrian Smith SDX just having two knobs for adjusting master tone and volume. While the neck still looks like a Strat, it is meant for fast and comfortable play, with its compound radius maple fretboard, 25.5" scale length, 1.6875" nut width and 22 jumbo frets. Giving this guitar its versatile tones are two single coils for the neck and middle position, along with a humbucker on the bridge, all of which are designed by Jackson with the approval of the Adrian himself.
I have owned a lot of amps over the years. I am also a dealer in music accessories. Please note that we do not sell these amps, so I am not endorsing and using something my shop sells. I recently have bought a couple of amps in a series (I bought one first and then bought another) and have been really impressed. The Vox AV series.
Martin’s first truly electric guitars were the Style F thinline archtops which began in prototype stage in 1961 and entered production in 1962. The F Series consisted of three models, the F-50, F-55 and F-65, all with bodies slightly less than 2″ thick and made of maple plywood with bound tops. All three had shapes roughly reminiscent of the dreadnought that made Martin famous, though slightly exaggerated with a wider lower bout. The cutaways were fairly wide and radical, cutting out at almost a right angle from the neck. The glued in necks had unbound 20-fret rosewood fingerboards, dot inlays and the typical squarish Martin three-and-three headstock. Necks joined the body at the 14th fret. Each bore an elevated pickguard and had a distinctive moveable adjustable bridge made of clear plexiglass.

1958-1969: replaces the "U" models and now has a double cutaway body with short horns. Masonite/poplar frame bodies, 13.25" wide. Models numbers include the "Standard": 3011 (black 1 pickup), 3012 (bronze 1 pickup), 3021 (black 2 pickup), 3022 (bronze 2 pickup), 5025 (blond 2 pickup). The 3021 is considered THE Jimmy Page model. "Seal" shaped pickguard and concentric knobs on 2 or 3 pickup models. Round control knobs.
Like many others, Reinhold Bogner (born in Ulm, Germany, like the EL84 tube!) started his career with Fender mods. He founded his company in 1989 in Los Angeles and succeeded in earning a reputation among guitar amp manufacturers. His brand became famous with models like the Ecstasy 100A and 100B, where "A" stands for American (with 6L6 tubes) and "B" for British (with EL34 tubes). Among its famous users, you'll find Steve Stevens and Steve Vai (apparently your name must be Steve to be Bogner's friend).
If your guitar is your personality, your amp is your voice. Together, they join forces to deliver your sound. Choosing the right amp ensures the audience hears each note, chord, bend, and trill-just the way you intended. From the compact convenience of a combo amp to the iconic stack to the bone-crushing fury of a wall of cabinets, your new amp is in stock and ready to ship at AMS. Read more
That’s not to say you need a specific guitar for each style — if you want a larger range of tones for different genres, a solid-body guitar is a good bet. There are also plenty of guitars on the market that include both humbucker and single coil pickups, thus allowing for even more sound options. Still seem too complex for you? If you look to the pros you’ll see that Gibson’s Les Paul and Fender’s Stratocaster have been used over and over again by recording artists. It’s not a coincidence: they’re capable of a lot of versatility. Yes, they differ from each other in tone, but with the right additional gear, you can replicate a ton of sounds.

The Afterneath gets a place on our favorites list, largely because of the "Drag" feature that allows you to sort of delay the decay of your reverb effect, giving off an ambiance that trails off behind each original note as it bleeds into new notes. It's a very unique reverb effect, which blends particularly nicely with a fretless bass in the example video below. 

It has great quality hardware and amazing sound because of the pickups. There are no flaws or nicks in the finish of the body. It needs to be set up though which can be difficult initially. Once you set up, you will be able to see its performance in action. The great thing about this guitar is that even though it is the cheapest electric guitar, it looks quite expensive to an observer.
With its playful old school appeal, many consider the Gretsch G5024E as a fun instrument to practice and perform with. Build quality and aesthetics are often cited in reviews, with many reports of the guitar eliciting positive response from friends and audiences. There are also reports from users who are very happy with both its amplified and acoustic sound.
1991 saw the introduction of guitar designer Jol Dantzig's first truly workable acoustic-electric hybrid guitar design. The instrument, called the DuoTone, was conceived while Dantzig was at Hamer Guitars. (Dantzig was also the designer of the first 12 string bass.) Adapted by players like Ty Tabor, Stone Gossard, Elvis Costello and Jeff Tweedy, the DuoTone was a full "duplex" instrument that could switch between acoustic and electric tones. Recently there have been many entries in the hybrid category (capable of both acoustic and electric tones) including the T5 by Taylor, Michael Kelly's "Hybrid," the Parker Fly and the Anderson Crowdster.
Yes, most of them are very useful! These days there are hundreds of online tutors offering great guitar lessons. And there’s no need to throw your money at the first offer you see, as a lot of quality instructional and tutorial videos are completely free on platforms such as YouTube. Generally, paid courses tend to be better because they are tested and are well-structured, and – in theory – you should be able to progress faster. But it all depends on your budget and on your will to learn on your own.
If you aren't planning to be in a band, i would get a modeling box like a POD, and just play on headphones. If you have the cash, I would just buy things here used on Craigslist, then sell them when I was leaving. If you know your prices, you could use the gear and get all your money back. Voltage issue is a problem with amps, one that is solvable, but seems like hassle for you. it really depends on your needs when here though.
The guitar sports an AAA flame maple top on a three-piece mahogany body, whose Translucent Black finish was picked by the man in the top hat himself. The iconic Firebird pickguard sits prominently on the axe, but this one features Slash’s “Skull & Top Hat” logo. The mahogany neck comes in a custom profile, too, which is rounded but slim enough for searing fretwork. A pau ferro fingerboard with trapezoid pearl inlays completes the cosmetic concerns on the axe.
The best way of working out which contact is which is to use a multimeter and see for yourself which contacts are connected to each other in the 5 switch positions. On the Fender-type and some import-type switches you’re given a good clue because you can actually see the mechanism or see through the switch casing. Watch this as you move the switch through the 5 positions – you can see which contact is always in circuit (the wiper) and which ones are in circuit in each position (1, 2, 3, 4 and 5). This method of visualising the switch also helps when it comes to fitting the switch to your pickguard and getting it the right way around! Now, where does the wire from the bridge pickup go again…
Jazz guitarist George Barnes is known to have played one of these prototypes in public in 1931, though far as I know, there's no recording of it.  Jack Miller played a "frying pan" in Orville Knapp's orchestra at Grauman's Chinese Theater in early 1932. Another musician, Gauge Brewer, bought two of the first available Beauchamp/Rickenbacher guitars, the other was a more conventional electrified Spanish guitar, and played them in a press event in Kansas, and a series of concerts around Halloween that year. Brewer also recorded both of these sometime in the mid-1930s, but it was one of the old direct-to-record recordings, a one-off, never released to the public (my Mom recorded a bunch of those 78s back in the 1940s and 1950s... tape wasn't quite there yet for regular folks).  Andy Iona was probably the first professional Hawaiian player to go electric.
Blueridge makes some excellent acoustic guitars, many of them based on historic designs. So, what does that mean? Many players feel that acoustics made in the early days after the dreadnought design had been created used better construction methods, qualities and materials compared to guitars produced today. In their historic designs, Blueridge attempts to capture some of that magic.

This is a very cool goldtop Vox SDC 33. Ultra slim body and neck makes playing extremely smooth and comfortable. Coaxe pickups provide a unique array of tones. Has some natural wear from normal use, like the buckle rash and a chip on the neck finish shown in the pictures. Overall a very clean and well playing guitar with a unique look and sound. Contact us with any questions! Thanks, Fondren Guitars

Some steel-string acoustic guitars are fitted with pickups purely as an alternative to using a separate microphone. They may also be fitted with a piezoelectric pickup under the bridge, attached to the bridge mounting plate, or with a low-mass microphone (usually a condenser mic) inside the body of the guitar that converts the vibrations in the body into electronic signals. Combinations of these types of pickups may be used, with an integral mixer/preamp/graphic equalizer. Such instruments are called electric acoustic guitars. They are regarded as acoustic guitars rather than electric guitars, because the pickups do not produce a signal directly from the vibration of the strings, but rather from the vibration of the guitar top or body.
What's funny is that guitars with cheap pickups very often sound better direct than guitars with "good pickups". I have an Epiphone Special I with ( presumably GFS ) P90-style pickups and that thing sounds great direct. It's also fine with a band thru an amp if the band doesn't play too loud - if the band's too loud the low mid buildup means you gotta EQ a lotta bass out and it loses it's girth.

Left Handed 1968 Fender Strat with an insanely rare Blonde Custom Color! This had to have been a special order guitar – has “Blond” written in the neck pickup cavity(see pic). I think I’ve seen one other factory left-handed Blonde Strat, but certainly not from the Hendrix era(both the white Woodstock and black Band of Gypsies Strats were from 1968).
The prime advantage of Epiphone is that you get a guitar built to the same specs as the Gibson Les Paul, at a greatly discounted price. With that being said, an Epiphone is not equal to a Gibson simply because it shares the same design. The craftsmanship is where the two brands differ the most, as USA made Gibson’s utilize higher quality materials than the Epiphone line. Epiphone uses a cheaper mahogany in the construction of its guitars, while the electronic components are lower quality as well.
In the late 1950s, Guitarist Link Wray began intentionally manipulating his amplifiers' vacuum tubes to create a "noisy" and "dirty" sound for his solos after a similarly accidental discovery. Wray also poked holes in his speaker cones with pencils to further distort his tone, used electronic echo chambers (then usually employed by singers), the recent powerful and "fat" Gibson humbucker pickups, and controlled "feedback" (Larsen effect). The resultant sound can be heard on his highly influential 1958 instrumental, "Rumble" and Rawhide.[17]
For experienced players, you already know what kind of questions need to be brought up when purchasing a guitar. For beginners, a great starting point is to look at what your favorite guitarists play. By taking your own musical tastes into consideration, you can narrow down your choices to models that will provide the tone and sound you already know and love. But whatever you're looking for, you can be certain that the perfect guitar for you can easily be found, right here. Just take a look around and see for yourself.

Hello all. I have a brand name guitar, which was very popular in the 1980s, and still is being manufactured under Gibson today. I didn't see it in your list though. It's a Kramer Stagemaster. It's a beautiful guitar, which I may never part with. Strat-Style with Neck-Thru-Body & Floyd Rose Trem. The headstock states Kramer American. These were passed off as American made models, however I understand that they were actually made in Japan. The style and appointments are strikingly similar to my Ibanez Proline 2550 from the same era, which has 'Crafted in Japan' written on the headstock. I know that Kramer made a lot of American made guitars out of Neptune, New Jersey, however these were all bolt-on neck guitars. Does anyone know where these Neck-Thru Kramers were made, or why they have American printed on the headstock if they are not tues American made guitars?
Now, since I have started on my wishlist there is another thing that I would like to add. I have seen multi angle videos that include a shot the finger board from the point of view of the player. Looking at this video angle it shows the fingerboard from the same angle as when you are playing it yourself. This is a great view as you do not need to translate what you see mentally. You see it, you play it the same way.
By 1970, regular distribution of Japanese-made guitars, including Lyle brand guitars, began in America. In the early 1970s, Arai joined with instrument manufacturing company Matsumoku to produce guitars. It is inconclusive if they continued producing Lyle guitars at this time, but they did launch the Aria Pro II line in 1975, which included set-neck copies of the Gibson Les Paul and SG, and Fender Stratocaster and Telecaster guitars.
What you need is some basic knowledge about the physics of audio (most of which you can learn by dropping a pebble in a puddle of water), and some pretty basic and inexpensive equipment. This is especially true for recording the electric guitar. Trust me--if it were brain surgery, I would have become a brain surgeon and made my mother a much happier woman. And while I have the opportunity . . . for all you kids who want to grow up to be recording engineers--don't do it. Become brain surgeons. They make a lot more money, drive nicer cars, and never have to worry about where their next gig is coming from.

However, it does give you a good flavour of the Martin and is a very playable plug-in, one of the best ways to see proper guitar emulation in action without paying for it. There are tab and effects options and a keyboard for playing it (we’ll assume if you can play a guitar, you’ll opt for the real thing, anyway). While it is free, we think you’ll be sorely tempted to upgrade, which will set you back $169.
Gretsch was founded in 1883 and started out making banjos - it wasn't until the 1930s that they began producing guitars - but during the 1950s their guitars began to take on legendary status. During the 1960s their popularity hit stratospheric levels because George Harrison was playing a modified 1957 Gretsch Duo Jet that he bought second hand for £70 from a ship crew member in Liverpool who had bought it brand new in New York. Most collectors agree that the 50s & 60s are the most sought after Gretsch guitars.

A difficult effect to explain, the compressor’s value is in it subtle and careful use. A compressor acts like bumpers on your signal's amplitude, preventing the volume from spiking too loud while also preventing the volume from decaying too quickly. Because of this, it increases sustain - which is great for solos - while evening out playing dynamics. Country and funk players use compression heavily to achieve spanky and crisp punctuation within their playing. Compressors will add noise to the signal, so many higher end boxes will have a noise gate feature. Other than making cleans sparkle, you can also front-load your distortion or overdrive to get great clear sustain.
With a delightful dreadnought shape, this steel-string acoustic is made with a pressure-tested solid cedar top, with solid mahogany back and sides, all with a semi-gloss custom polished finish that allows the guitar to sing – and sing it does! The tonewoods combine to deliver a rich and bright sounding instrument, with plenty of warmth that would please the most demanding of guitarists.
Some studios are too small for regular amp miking, and even if they're not there are sometimes occasions on which you need better separation from the other instruments playing at the same time. A neat way around this is to use a soundproof box containing a guitar speaker and a microphone. Various commercial models are available where your guitar amp output feeds the speaker inside the box and the microphone feed comes out to the mixer in the normal way. The designer's challenge is to make this work without the resulting cabinet being too large or too boxy sounding. The DIY alternative to this is to place the combo or speaker cabinet in an adjoining room, or maybe even a cupboard or wardrobe (along with the mic, of course!).
With a 25.5” scale length, the 314ce features a Grand Auditorium body shape with a playability-enhancing Venetian cutaway, allowing good access to the highest of the 20 frets. The top of the body is made from solid Sitka spruce, along with solid sapele back and sides, leading to a beautifully rich and powerful tone that’s well balanced between warm and bright.

Run a length of wire (approx two feet is usually plenty) through the jack mounting hole and down into the cavity. When you see the wire in the cavity pull it up through the F hole. Make sure the wire is long enough for one end to stick out the jack hole, and the other to stick out the F hole. Tape the jack hole end of the wire to the guitar with masking tape, or tie it to the strap button. This will ensure it doesn’t fall through the jack hole while you’re working on the other end.

Joe Perry is the American distillation of the good-old Keith Richards/Jimmy Page recipe for sideman/lead guitarist cool. He’s got the look and the licks, and he’s maintained both over the course of three or four decades—despite all odds. Jagger and Richards are the Glimmer Twins, but Perry and Aerosmith singer Steven Tyler went down in history as the Toxic Twins.
Again, as with the bridge saddle, too low of a bridge will decrease the "drive" of the strings. Thus the sound and tone will suffer. Also a low bridge is structurally not a good idea, as the bridge can more easily crack (and damage the top of the guitar). Most original Martin guitar bridges are about 3/8" tall (from bottom to the highest part of the bridge).
I’m Björgvin Benediktsson. I’m a musician, audio engineer and best-selling author. I help musicians and producers make a greater impact with their music by teaching them how to produce and engineer themselves. I’ve taught thousands of up and coming home studio producers such as yourself how to make an impact with their music through Audio Issues since 2011.
Ken Rosser picked the Spider Classic 15 as his favorite of the amps we tested, saying, “I think the effects on the Line 6 sounded the best. It gives you a nice range of tone options. The clean tones stay clean even at loud volume, which a lot of these can’t do. One caveat is that, when you switch the amp sound, it changes the way all the knobs work, so the sounds can really jump out at you.” Fred Sokolow liked the Line 6 in general, saying, “I could pretty much figure out what to do with it, but I could figure out the Fender more easily.”
Two types of switches are commonly used for guitar mods. One is a potentiometer with a switch—a push/pull, push/ push, or the Fender S-1—and the other is a common toggle, which is available in different sizes, shapes, and configurations. When adding a switch to a passive circuit, you don’t have to worry about voltage and power ratings—all that matters is that switch will fit your guitar!
“Perhaps the weakest block, and the only one I spend time trying to dial in a decent tone. Lots of high gain fizz options with loss of body and character. Boost is decent, Tscreamer isn't, but for me the Blues choice with drive=1pm, tone=noon and output=11am gave a nice breakup tone without losing bottom end. If you have an overdrive pedal you may still be using it.”
One cool thing about liking oddball old guitars is they always contain hope…and a challenge. By which I mean, no matter how obscure or exotic, you always live with hope that you’ll someday figure out what the heck they are and thrive on the challenge of trying to do so. At least that’s been my repeated experience over the last quarter century or so of playing guitar detective. That being said, this 1967 Apollo Deluxe was kind of the exception that proved the rule, in that it followed a reverse pattern, sort of backing into discovery.
As you know, like most guitars sporting more than a single pickup, your Strat lets you select any pickup by itself or choose certain dual-pickup combinations. The standard way to connect multiple pickups is to wire them in parallel. This generates the classic tone our ears know from countless records, when a guitarist uses the bridge and middle or middle and neck pickups in tandem (positions 2 and 4 on a normal 5-way Strat switch).

I wonder if this list shouldn’t be renamed as Best Electric Guitar Brands, since there does seem to be a strong focus on electric guitars in this list. Yamaha does make a very good line of acoustic guitars, and Ibanez and Epiphone also manufacture acoustic guitars, and the Gibson Hummingbird would make any top 10 list of acoustic, but it’s the only one on this list that seems world class for an acoustic manufacturere(other manufacturers on the list may also make acoustics, but I’m not familiar with them) I doubt if they would be considered the best guitars or the most highly respected brands.

Some of the earliest electric guitars, amps-in-cases, pickups under the bridge, fiberglass guitars, built-in electronic vibratos. Sound curious enough for you? The subject of Supro guitars and amplifiers represents a profitable avenue for exploration by collectors and enthusiasts interested in the many curious and significant byways off the guitar superhighway, which can be enjoyed without having an oil sheik’s bankroll. While National resonator guitars have received superb attention by Bob Brozman, little has been written about this mysterious corner of the Valco universe. Well, with a little help from our friends (in particular, catalogs and invaluable information supplied by Mike Newton, Jim Dulfer, and Michael Lee Allen), let’s set the record straight.
Taylor also has a Build-To-Order program that allows anyone to design their very own guitar. There’s an extensive menu of guitar options starting from tonewoods, including species and grades that aren’t offered through Taylor’s standard line; inlay, binding and purfling options; finish options such as solid colors, sunburst, or vintage finishes; wood accents like a backstrap, armrest or truss rod cover; neck options such as scale length and neck profiles; and finally body shapes including the deep-body Dreadnought and the new Grand Orchestra.
The best advice any guitar player can give when it comes to figuring out which guitar to get is to buy the best model your money can afford. In most cases, this advice is rock solid. Even if you are a beginner who isn't sure whether or not you want to commit to playing guitar long term, you can always sell the guitar with a minimal loss, like a decent car versus a junker.  Think of it as an investment as long as you maintain and take care of it.
Taylors have a "happier" sound and I like the feel of them. I am a novice but from what I have seen for a beginner with an acoustic guitar, they felt and sounded warmer and less tinny than the laminated wood ones. A good rosewood taylor isn't on the cheap side of things but it feels like you can play better than you can. And the model I looked at had strings that were nice and close to the frets so you didn't feel like you were pushing in deep like the keys of an old typerwriter. Go into a Guitar Center or somewhere you can actually feel what you are getting before you buy anything. I got a cheap Gibson online less than a month ago and got what I paid for when it came with the bridge completely missing and a brassy sound when it was played. Buy your stuff in person. I think that Gibson is probably still a good brand, but the quality control of the cheaper models they put their name on is something I might question from my first experience with them...
You should add the plugins on They are all free and are great. They use them as tools to help them design physical amps, so they are very accurate and almost zero-latency. They have a few amps and pre-amps, 2 OD pedals and even a cab modeller which is more than enough to get you started. The Emmisary is a freakin' miracle. It can do any tone (I use it for metal, blues, clean) but it's best for molten, in-your-face heavy metal since it has a 4-way EQ on the lead channel.

Add a maple top to the mahogany body, as do a great many Les Paul models, and a blend of characteristics comes forward. The mahogany’s depth and richness remain, but the maple provides added snap, clarity, and definition. It also tightens up the lows and adds more cut to the highs. For many players this sonic evolution is highly desirable, whereas others might prefer the smoothness of the pure-mahogany design.

According to the laws of electromagnetism, whenever an iron coil is moved inside a magnetic field, an electric potential is generated in the iron coil. This arrangement is known as an electromagnet. An electric guitar uses the same principle for generating an electric signal using small electromagnets which is then rectified and amplified to reach an appropriate audible sound level.
As a beginner most people are not very sure of the sound, style or type of guitar that they would ultimately like to play, but after playing for 6 months or so I’m sure you will know a lot more about guitars and when it comes time to choose your next guitar it will be an easy choice. The key features a beginner needs is a guitar that is well set-up and easy to play, but you don’t really need to spend too much money on getting a better quality of sound. Higher level guitars will only sound better when your playing has progressed to the level that you can play quite well.
The first part of this book shows why Guthrie is such a great player, and dives into his mindset when it comes to teaching and playing. I really believe you should go buy this book, so I don't want to give too much away, but he covers great topics like how to avoid guitar injuries, setting goals for yourself, thoughts on technique, tone and gear, and general tips on how to practice.
The intervals between the notes of a chromatic scale are listed in a table, in which only the emboldened intervals are discussed in this article's section on fundamental chords; those intervals and other seventh-intervals are discussed in the section on intermediate chords. The unison and octave intervals have perfect consonance. Octave intervals were popularized by the jazz playing of Wes Montgomery. The perfect-fifth interval is highly consonant, which means that the successive playing of the two notes from the perfect fifth sounds harmonious.

Effects are electronic devices and circuits that process the electronic signal input from an instrument or mic. Also referred to as FX, they run the gamut from limiter or expander settings so subtle you can barely detect them to sci-fi modulation effects so extreme that the original sound is virtually undetectable. Think of your guitar or bass as your artist’s palette of primary colors. Effects are the equivalent of your brushes, tools, and color-mixing skills that add near-limitless creativity to your artistic vision.
Position 2 (outside coils, parallel connection): this one is more exciting because all poles do something. Pole 1 connects bridge pickup coil tap to ground, effectively splitting the bridge pickup. Pole 2 connects bridge pickup hot lead to the output. Pole 3 connects neck pickup coil tap to pole 4 which connects it to the output. What we end up with is a coil from bridge pickup coil tap to hot lead and a coil from neck pickup ground to the coil tap. Because of the way poles 2 and 4 are connected, these two coils will be paralleled.
Except if, like George Gruhn, you know better. The 71-year-old Nashville dealer has sold guitars to Eric Clapton, Neil Young, Paul McCartney and Taylor Swift. Walking through NAMM with Gruhn is like shadowing Bill Belichick at the NFL Scouting Combine. There is great love for the product and great skepticism. What others might see as a boom — the seemingly endless line of manufacturers showcasing instruments — Gruhn sees as two trains on a collision course.

The Effect: Vibrato effect, often mistaken for a tremolo, is the type of guitar effect that alters the pitch of your signal. The result is very similar to that which you get when you operate the tremolo bar on your guitar. There are different types of vibratos out there, but the most common division is between analog and digital units. Analog vibratos are known for their clarity and organic feel that comes from analog pitch shifting.
Recently while cruising around EBay I was able to find pretty strong evidence that the 700 and 800-series Kents were made by Kawai. Or maybe... the necks of the 700 and 800-series Kents and the Kawais were made by the same manufacturer. I don’t know if Kawai kept the factory that made Teisco operating after it was acquired. It appears that Kawai had more experience building hollow-bodied guitars than Teisco. So I call the 700 and 800-series Kents Made by Kawai. You can call them Made by Teisco if you want. Of course, the possibility exists that they were both made by an entirely different company. Who knows? The 1960’s were like a ‘wild west’ period of Japanese guitar making.
{ "thumbImageID": "GRX70QA-Electric-Guitar-Transparent-Blue-Burst/H77128000001000", "defaultDisplayName": "Ibanez GRX70QA Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Transparent Blue Burst", "sku": "sku:site51313248770709", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Blue-Burst-1313248770709.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Blue-Burst/H77128000001000", "brandName": "Ibanez", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Transparent Red Burst", "sku": "sku:site51313248770799", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Red-Burst-1313248770799.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Red-Burst/H77128000003000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Transparent Black Sunburst", "sku": "sku:site51313248770729", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Black-Sunburst-1313248770729.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Black-Sunburst/H77128000002000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }
Many modern players use the first joint of the thumb against the back of the neck, and almost on the upper binding, sort of like gripping a baseball bat, so they can reach over the neck with their thumb tip to play bass notes on the E and A strings while picking melodies out with the other fingers. Tommy Emmanuel, and Andy McKee are particularly adept at this. You’ll need to experiment some to find what works best for you.

My 15 year old daughter recently renewed interest in the guitar she had bought a few years ago but had never really played much.  She was disappointed when she noticed the strings were loose.  We brought it here and Ted was so helpful and engaging. He recommended new guitar strings; normally you can buy the strings and do it yourself, or pay them to do it.  He readily understood that while my daughter didn't know how to do it herself, she would like to know. He showed both my girls how to string a guitar, talking them through each step while he expertly strung the guitar and got it in perfect tune. Ted teaches guitar and his tutorial was an excellent recommendation of his teaching skills.  He also threw in a cleaning cloth and gave us chocolates - how much better does it get than that?!

The Pro Series DK2 is a rugged, performance-grade workhorse that’ll do just as well on the stage as in the studio. It has a lightweight okoume body—a tonewood that shares many qualities with mahogany—as well as Jackson’s fast maple ‘speed neck,’ a compound radius ebony fretboard and 24 jumbo frets. A recessed Floyd Rose 1000 double-locking trem system completes the shred-friendly features on the guitar.
These pedals essentially do the same thing with overdrive being regarded as a milder effect, similar to turning a tube amp all the way up and distortion a more extreme version of the same effect. Although these are designed for electric guitar, I’ve seen acoustic players use them to great effect through an amp or PA. If done well it provides a dramatic lift to a song. The most important thing is to be familiar with the sound and volume your pedal will create before you try it live.
Not something you have to think about with an acoustic guitar, the electrics in an electro acoustic are quite important, though not as critical as with an electric guitar. You’ll want to make sure that you’re getting a good quality pickup and preamp, and then the next thing to consider will be features. Preamps often come with EQ adjustment to alter the tone slightly, and some will even come with certain effects that you can add on. Builtin tuners are a common addition too which mean you don’t need a separate tuning box.
So don't hesitate; your next multi effects pedals, rack-mounted units and accessories are probably waiting just a few clicks away. The only thing better than a board full of great pedals is one box that combines all those great pedals into a single convenient package - and once you've got that multi effects unit onstage with you, the possibilities are virtually endless for the personalized tones and unique sounds you'll be able to bring to every performance.
This full-size electric guitar from Davidson is all that you need to start playing master the very art of strumming. The quality, durability, comfort, and accessories that are required to get you started is included in this solid guitar package from Davidson. This is a full size (39 inches) and complete scale solid electric guitar made of maple wood. It is an electric guitar featuring a maple neck and gloss finish.
What’s the point in having these lists anyway? There’s always going to be anger over people who were left out/included on the list when they didn’t deserve to be… And to say that any of the musicians mentioned so far aren’t talented is ridiculous, there’s no limit in the world on how much talent there is, so why does this list have to be limited to 10? Just saying…
Peterson, Jonathon (2002). "Tuning in thirds: A new approach to playing leads to a new kind of guitar". American Lutherie: The Quarterly Journal of the Guild of American Luthiers. 8222 South Park Avenue, Tacoma WA 98408: USA.: The Guild of American Luthiers. 72 (Winter): 36–43. ISSN 1041-7176. Archived from the original on 21 October 2011. Retrieved 9 October 2012.
ASSEMBLE Now you can put it all together! By this time you'll be so excited you'll forget about the electronics and start to string in up before you get the electronics in but it's ok, we'll get there. Start with bolting on the neck in the same fasion that you did when you test fitted everything. Then follow that with the tuners, bridge and pickups. Don't forget to run the wiring for the pickups when you put them in.
The Articulations page exposes all of the Shreddage II articulations to the user in a fully-customizable mapping scheme. The user can activate articulations via keyswitches or velocity ranges. The Engine page reveals the back end of Shreddage II for users seeking to tweak Shreddage II into the ultimate performance tool, with controls for velocity response, transposition, pitch bend range, resonance controls, pedal behavior, and control over noises like release and pick.

Multiple stages of valve gain/clipping can be "cascaded" to produce a thicker and more complex distortion sound. In layperson's terms, a musician will plug a fuzz pedal into a tube amp that is being "cranked" to a clipping "overdriven" condition; as such, she will get the distortion from the fuzz which is then distorted further by the amp. During the 1990s, some Seattle grunge guitarists chained together as many as four fuzz pedals to create a thick "wall of sound" of distortion.
The woods used on the body and neck are worth considering too, although are unlikely to be a defining factor when you consider your purchase. Basswood features heavily as the body wood of many guitars in this price range because it’s affordable and has decent tonal properties. You will also find cheaper to produce woods like poplar and alder, although the traditionally more premium mahogany is also found on affordable guitars these days.
I was a little concerned buying a guitar on Amazon. I had not even played a sample on the Gretsch acoustic. I've played Martins, Fenders, Washburns, etc. but never heard of the 'Gretsch'! It arrived within a few days of ordering with the case I ordered too. I had it delivered to my office so that it wouldn't be sitting on my porch until I got home. I opened the box to examine the guitar and co-workers asked me to play something. As I was tuning the white Gretsch I broke a string, so playing it for my friends was not going to happen. When I got home I re-stung the guitar and as I was tuning it I was not very impressed. I like the look but come on we purchase a guitar to play! After it was tuned I began to play a few chords and licks.
Any guitar luthier will tell you that the choice of wood is the single MOST IMPORTANT factor that will determine the sound of your guitar. My junk guitar had a body that was made of cheap reconstituted wood shavings instead of actual solid wood. Junk material like that means your sound will also be junk. Any note I played didn’t sustain for more than a single second and it didn’t have that boomy lush sound you normally get from acoustics.
Clock maker Matthias Hohner began crafting harmonicas in 1857, assisted by his wife and a single employee. 650 were made in the first year.[1] Hohner harmonicas quickly became popular, and in his lifetime Matthias built the largest harmonica factory in the world.[2] During the American Civil War, Matthias Hohner distributed harmonicas to family members in the United States who in turn gave them to the soldiers.[3]

The Legacy’s vintage-spec CLF-100 Alnico V pickups have that unmistakable chime and quack reminiscent of the best examples from the late ‘50s, thanks to the work of Paul Gagon, G&L VP Engineering. Gagon found his inspiration reviewing original prints stored in Leo’s private laboratory at G&L, but that was just the start. About 30 years ago, Gagon was an R&D engineer at another company when he was tasked with finding out what was so special about the early bolt-on guitars many players raved about. Gagon tirelessly analyzed many examples of what were considered holy grail guitars, spending time out on the shop floor talking to builders still working in the pickup department since the ‘50s, all on a quest to discover where the real mojo was – and wasn’t. What he learned from the builders matched his own engineering analysis. You see, back in the day, the actual spec of pickups coming that down that old production line varied considerably. That meant coming up with the right specs for the Legacy pickups was more challenging than simply following the prints. Gagon’s persistence paid off as the Legacy garnered rave reviews from both players and magazines like Guitar Player and Guitar World.
"Rocksmith 2014" is geared toward beginners and starts with the basics, like getting your guitar in tune. Then it'll pick a song based on your skill level. The earlier version's "journey" mode has been replaced by a "mission" mode (it is a video game, after all) with tasks like playing a song that "Rocksmith" recommends or hitting 75 percent accuracy. You get feedback after each run through a song, and you have tasks to check off as you play, like hitting five notes in a row. As you succeed, the game throws more tasks and notes at you, adjusting the difficulty as you go.
As one user put it, this is one of “Amazon’s hidden little gems”, with a good set of tube electronics that gives out a natural sounding overdrive and some crystal-clear rhythmic sounds. If you want to make your guitar sound clear enough to accompany Porcupine Tree while also having the option for a natural grainy sound that might work well for jazz and blues, then this item is definitely something to look into.  
You don’t have to go for the ones that cost thousands of dollars; there are some pretty decent ones that cost less than $300. What a multi-effects unit will allow you to do is to experiment with different effects and this will give you an idea of what kind of effects you will need to get a certain sound. Once you have a good idea of what kind of effects you’d like to use, then I certainly do recommend trying out individual pedals and building a pedal board. Either that, or you can definitely upgrade your multi-effects to one that has more authentic sounding effects and modelers.
Want to write blazing leads and screaming solos? Crank the pitch bend up, use one of four vibrato modes, and shred to your heart's content. Need some ultra-chunky rhythm chugs? S2 features both single-note and powerchord palm mutes with up to 5 layers and 8 variations each, offering superior realism and maximum options. While it excels at rock & metal playing (both lead and rhythm alike), it is also well-suited for many other genres thanks to its clean tone and huge range.

As a rule, acoustic guitars with laminated spruce tops do not have the same resonance as those made from unlaminated tonewoods, but the Fender FA-100’s fuller dreadnought design provides a richer tone than some customers may expect. If price is a consideration, the Fender has been described as a “cheaply made guitar with a fantastic sound.” What’s more, When you buy a Fender product, you're investing in quality. The Fender Musical Instruments Corporation has been manufacturing instruments and equipment since the 1940s.

I am a lawn tennis and guitar playing trainer. I am a college lawn tennis varsity player and became a coach and a trainer of beginners and advance tennis players. I am also a band player and singer performing musical folk, pop, ballad and jazz pub Shakey's Pizza Parlor and chains. I worked with Yamaha Music Corporation as an account representative.
TonePad – provides ready-to-use layouts and circuit boards for effects and amplifier projects to the do-it-yourself music community. All layouts are provided free of charge and are subject to the limitations set forth on their legal page. Parts are available from Small Bear Electronics, and ready-made PCBs for many projects are now available directly through tonepad.
Any guitar luthier will tell you that the choice of wood is the single MOST IMPORTANT factor that will determine the sound of your guitar. My junk guitar had a body that was made of cheap reconstituted wood shavings instead of actual solid wood. Junk material like that means your sound will also be junk. Any note I played didn’t sustain for more than a single second and it didn’t have that boomy lush sound you normally get from acoustics.
Quality-wise, they range from complete and utter crap, to OMG! Acoustics, tend to fall into the former range. Electrics, mostly the hollow bodies, were somewhat, but not always better. Solid bodies, mostly made from plywood, BUT they do have their own feel and sound. I happen to love them, others despise that cheap feel and sound. Remember, they were built to fill the growing demand of guitars, that the kids saw on tv, with the Monkee's and the Beatles
I have a Lyle Acoustic Guitar Model 690 purchased about 1966 or 67. It appears to be in near brand new condition as I've rarely played it and it has been stored in a felt lined case its entire life. All the keys still turn, it has steel strings. I'm ready to part with it and want to ask a fair price and not get soaked. Does anyone have any idea what this beautiful instrument is worth?
If you see a "\n/," where n = some number, perform a tremolo bar dip. Quickly hit and release the bar to dip the note's pitch. The number between the slashes gives an indication of the pitch you should dip to - dip the pitch by "n" semitones (a semitone is the same as the pitch between two adjacent frets.)[1] For instance, "\5/" means to drop the pitch by 5 semitones, which will be the same tone as 5 frets below the original note.
The Ibanez DT-250 is a perfect guitar for shredding. The basswood is light so you can run all over the stage, jump off your stack, and still have energy to dive-bomb. Even do the splits. Notice that was a “you can.” These were outfitted with a pair of blade-pole V5 humbuckers, produced toward the end of Japanese-made pickups, before Ibanez started working with DiMarzio. They are smokin’ hot! This guitar almost leaps out of your hand when you plug it in. The Japanese improvements on the locking vibrato were also impressive, and this combines the precision of a Floyd Rose with the feather touch of a Kahler.
Next up is this beautiful standard Telecaster from Fender. All the words in the name are words that appeal to us. Fender is a well-renowned brand that most guitarists consider a safe option that delivers great guitars. The next word, ‘Deluxe’, suggests that this particular guitar is a little bit better than all the rest, and then we have Nashville, which makes all country enthusiasts curious.

Some of the different aspects of the SG include its much thinner double cutaway body that offered players easier access to the higher frets.  This model is also significantly lighter than the Les Paul and was preferred by many players who wanted the heavier tonal offerings without the back and shoulder pain that can come after a 3 hour gig with a Les Paul.
Phasers work in a way similar to flangers, but this time the copy of the signal is filtered to bring it slightly out of phase. This creates a sweeping, futuristic sound at cranked-up settings, but dialed down will get a chewy, textured tone that’s even suitable for rhythm playing. Eddie Van Halen is one guitarist well-known for his application of the phaser. Today he employs his own signature effects pedal, but his classic MXR Phase 90 is legendary among guitar tone nerds.
Whether you call us Guitar Center Forth Worth or GC Cowtown, it's all the same to us! One way or the other, we'll be sure to send a smile and a big Texas "Howdy!" your way when you walk in the front door. Conveniently located on South Hulen Street, we're just a stone's throw from Hulen Mall, near the Chisholm Trail and I-20 interchange. Turn in when you see Chili's, and get ready to experience the down-home vibe that's been growing our community of regular customers since our grand opening back in 2004.First and foremost at Guitar Center Fort Worth, we strive to give you the experience that Guitar Center is known for nationwide: big-store selection and prices with small-shop expertise and personality. From sales to repairs, our staff in each department is well-trained to cater to Dallas/Fort Worth area music-lovers. Our store is open every day of the week, so there's always a right time to visit even if you're on a busy schedule.
Perhaps our favorite feature is a far more subtle aspect of this pedal's interior, which is a circuit design that runs your dry signal through an analog path, before reuniting it with the wet reverb signal, which is produced by a digital processor. This means your guitar's signal coming into the pedal is unimpaired by the digital components, giving you a far more pure and organic-sounding output. 
There are two main types of amplifier: valve and solid state. Solid state guitar amplifiers tend to be cheaper and lighter, but they don't offer as good a sound as valve amplifiers. Valve ones, on the other hand, have working parts, so they're a little more maintenance heavy. Most serious musicians go for valve amplifiers due to the superior sound and lower wattage requirements.
Boutique pedals are designed by smaller, independent companies and are typically produced in limited quantities. Some may even be hand-made, with hand-soldered connections. These pedals are mainly distributed online or through mail-order, or sold in a few music stores.[98] They are often more expensive than mass-produced pedals[99] and offer higher-quality components, innovative designs, in-house-made knobs, and hand-painted artwork or etching. Some boutique companies focus on re-creating classic or vintage effects.[100][better source needed]

While the decision to choose between bridges can be an overwhelming one, to simplify things, it’s better to choose one that’s appropriate for your skill level and your personal taste in music.  One bridge for the heavy metal genre may be absolutely frustrating for a country player.  For those with numerous guitars, you might have a different bridge on each instrument to suit that situation or style of music.
The Martin DSR2 also comes equipped with built-in Fishman Sonitone electronics, which features discrete soundhole mounted controls, allowing for stage-ready performance without having to drill excessive holes on the side of the body. With its continuesly high rating and incredible value for money, the Martin DSR2 should be at the top of your list when you're looking for an acoustic-electric guitar in this price range.

Tremolo can be a subtle effect, as heard in “Born on the Bayou”by Creedence Clearwater Revival and Gimme Shelter by The Rolling Stones, or more distinct as heard in “Crimson and Clover” by Tommy James and the Shondells and “Bones”by Radiohead. Tremolo has been around since the earliest days of the rock era, and was popular with rockabilly and surf guitarists.
Most new electric guitars tend to ship pre-strung with "super light" guitar strings. Depending on your technique, and the style of music you play, that string gauge may or may not be too light for you. The following is a list of the standard string gauges included with each set of electric guitar strings. Note though that different manufacturers include slightly different string gauges in their sets of strings.
A spring reverb unit is really a small amplifier in itself, that sends the guitar signal through a tube circuit to a small output transformer (or through a transistorized circuit) and from there to one end of the springs in a spring can rather than to a speaker. This signal vibrates the springs, is picked up by a transducer at their opposite end, and from there is blended back with the dry signal by degrees determined by a “depth” control, and sent on to the output (or the power tubes, if part of a guitar amp). As you can image, it’s a bulky effect when achieved in this way, requiring at least a couple of transformers, two or three tube sockets and a spring can, but the circuit itself is fairly simple.

The Kay guitar company's origins date back to the 1890's, starting with the Groeschel Mandolin Company of Chicago, Illinois. The company's name was changed to "Stromberg-Voisinet" in 1921, and shortlyafterwards, in 1923, Henry Kay "Hank" Kuhrmeyer (the origin of the name "Kay") joined the company and quickly worked his way up to the top. By 1928, Kuhrmeyer had bought the company and that same year the company started producing electric guitars and amps.
Guitar models currently include the Master Class, American Series, Oregon Series, Cascade series, Atlas series, Passport Plus, and Passport, as well as 12-string models and Bass models. The Voice series, reviewed by Guitar Player in 2012, was praised for the quality of construction and various innovative elements, including a “Tru-Voice Electronics System” which, according to Dave Hunter, “for live performance … comes closer to a seamless acoustic-to-amplified transition than virtually any other flat-top I’ve played.”[2]
To create a thicker rhythm guitar sound, overdub the same part one or more times. Depending on the desired effect, the overdub can be treated as one mono signal and mixed to the same stereo position, or panned left and right for a stereo double-tracked sound. Alternatively, treat the original track with an ADT (Artificial Double Tracking) effect. This can be done with a digital delay set to around 40 milliseconds. Again, the delayed signal can be panned or mixed as one with the original guitar track.

I have a very unique Lyle guitar. It is apparently a 1972 but on the headstock it has the pearl from Gibson and it says Gibson on it as well on the headstock. It has the tail trapeze and the adjustable saddle. I recently had it set up and there is absolutely no fret buzz, it looks like it just came off the wall, stellar condition. My tech was stunned at the body condition and even the frets were like a new guitar? This is the only guitar I have seen that is definately a Lyle but it has Gibson, correctly done on the front of the headstock? I went in to the acoustic section and played a Gibson new hummingbird next to mine and it sounded cheap! I was stunned. I have no idea what this is worth but is like the perfect guitar. No dents, nicks, scratches, just and old guitar that has been babied, no warping anywhere, I think this will play another 30 years easy. If anyone knows about a Lyle with a Gibson logo and Gibson written on the headstock, please let me know
The one-string guitar is also known as the Unitar. Although rare, the one-string guitar is sometimes heard, particularly in Delta blues, where improvised folk instruments were popular in the 1930s and 1940s. Eddie "One String" Jones had some regional success.[citation needed] Mississippi blues musician Lonnie Pitchford played a similar, homemade instrument. In a more contemporary style, Little Willie Joe, the inventor of the Unitar, had a rhythm and blues instrumental hit in the 1950s with "Twitchy", recorded with the Rene Hall Orchestra.