The downside of boosting the volume of an acoustic guitar this way is the fact that every microphone adds a color of its own to the end result, not to mention the preamplifier and any compression and equalization applied. In other words, not only do you have to position the microphone correctly, but you also need to be very careful when choosing which mic to use.

Guitarists don’t have to just look on in envy as pianists lead the holiday sing-a-longs this Christmas. Our selection of holiday Guitar Tabs include traditional classics we all love like “O Holy Night” and “Carol of the Bells” and the pop favorites that just wouldn’t be the same without a guitar, like “Jingle Bell Rock” and “Happy Xmas (War is Over)” by John Lennon. But if you just can’t get enough of those traditional Christmas classics, you can pick up our collection of ’Christmas Favorites for Guitar.’
I’m starting at guitar too at sixty years old, my opinion is that it’s not the guitar, but the time put into practicing, you can dup any type of sound with the features from amps, and guitar processors. You can even make an electric guitar sound like an acoustic. I purchased a line 6 150 watt amp, and a processor from line six, and I can dup any type of guitar sound. I built my own guitar
Another tone option for a guitarist is to put a pickup out of phase with another pickup, producing a thin "inside-out" squawky kind of sound. When 2 pickups are in phase, they work together and reinforce each other. When they are out of phase the 2 pickups are working against one another and the resulting sound is the "leftovers" from these cancelations. The closer the 2 pickups are, the greater the cancelations, the thinner the sound and the lesser the volume. Therefore, the neck and bridge pickups out of phase is the best choice for this type of sound.
A Reamp® box is essentially the reverse of a DI box and converts a balanced signal into an unbalanced signal suitable for driving guitar amps. Radial makes three different versions of this device with variations in features and in quality of the transformers. For an introduction to reamping there is the passive ProRMP™, for high quality reamping there is the Reamp JCR™, and at the top of the line is the dual-channel active X-Amp™.
* 3 most basic reverb modes: Room: Simulates the spaciousness of a room; Hall: Simulates the spatial dimension of a music hall; Plate: Simulates the unique reverberation character only coming from a plate reverberator. * One reverb control balances the dry/wet signal, simple enough to dial in the perfect amount of reverb for your tonal needs. * True bypass for zero tonal coloration. * Extreme mini size for great compactness. * Heavy-duty metal casing for great stability and durability; Connectors include input, output, and power supply; Powered by 9v DC. W/ a 6 inch patch cable included. SONICAKE Digital Reverb is reverb pedal designed to add dimension and spaciousness to your tone. It is extremely straight-forward to use with only one “Reverb” knob to adjust the balance between the raw d.

In the early 1980s, some performers began using two-way or three-way cabinets that used 15" woofers, a vented midrange driver and a horn/driver, with an audio crossover directing the signal to the appropriate driver. Folded horn bass guitar rigs have remained rare due to their size and weight. As well, since the 1990s, most clubs have PA systems with subwoofers that can handle the low range of the bass guitar. Extended range designs with tweeters were more the exception than the rule until the 1990s. The more common use of tweeters in traditional bass guitar amplifiers in the 1990s helped bassists to use effects and perform more soloistic playing styles, which emphasize the higher range of the instrument.
From shopping for a first electric guitar to setting customized action, this do-it-yourself playerÕs primer for owning and maintaining an electric guitar explains the ins and outs of: choosing the right guitar; cleaning, tools and basic maintenance; personalizing and improving on a "factory setup"; trouble-shooting; basic guitar electronics; setups of the pros; and much more. Written by Dan Erlewine, author of the bestselling Guitar Player Repair Guide and the popular "Repairs" column in Guitar Player magazine, this book also includes a plastic sheet with specialized guitar tools you can snap-out!
The Dobros and Nationals were joined by the first Supro guitar versions in late 1935, even though their announcement didn’t appear until a few months later in the March, 1936, The Music Trades. These first Supro guitars included an aluminum Hawaiian lap steel, both electric Spanish archtop 6-string and tenor guitars, and an electric mandolin. They mark the official beginning of the Supro story.
As an aside, people talk about “gold foil” like it’s some sort of rare mineral!  I see auctions all the time dropping words like “GOLD FOIL” pickups, and “As played by Ry Cooder!!!”  So far, I’ve identified 12 different kinds of pickups that had gold foil somewhere on them, and many of them are made differently!  What’s the point?  Don’t buy the hype!!  You have to play these guitars, or check out our videos to get an idea pertaining to sound.  Poor Ry Cooder gets attached to every darn gold foiled guitar ever made, geesh!  And I don’t even know who Ry Cooder is!
Description: Body: Basswood (Tilia, Linden, Lime) - Body Construction: Solid - Neck Attachment: Bolt - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 24, Jumbo - Inlay: Dot - # of Strings: 7 - Scale Length: 25.5" (65cm) - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Chrome, 1x Volume Control, 1x Tone Control, 3-Way Switch, Grover Tuners - Pickups: Dean - Pickup Configuration: H-H - String Instrument Finish: Metallic Cherry, Metallic Black, Transparent Red
Some Craigslist and EBay sellers have been claiming the 500 and 600-series Kents are made by Teisco. I think we’ve shown that that’s not the case. Some sellers also describe those early Kents as having “Ry Cooder” pickups. As most of you know, Ry Cooder is an incredibly talented multi-stringed-instrument musician. David Lindley, another great talent, gave him a pickup from an old Teisco guitar. The photo at left is exactly like it. Cooder put the pickup into one of his Stratocasters and liked the sound so much that he got another one and put it into another Strat. These pickups are also described as “gold foil” pickups. There are variations in the pattern of cut-outs on the chrome covers of different pickups. I don’t know if the others sound any different, but if I were looking for a “Ry Cooder Pickup”, something like the one pictured here is what I would be looking for. The pickups have become worth more than the guitars they are on, consequently, as the guitars are bought up and trashed for their pickups, their prices are going to rise.
These two articles show us how me can manipulate coil winding direction, electrical phase, and magnetic polarity to achieve hum-cancellation between two coils. Having this knowledge allows us to create hum-cancelling combinations of coils over and above than just using humbuckers. A good example is using a RWRP pickup in the middle position of a Strat.
A guitar amplifier (or amp) is an electronic device or system that strengthens the weak electrical signal from a pickup on an electric guitar, bass guitar, or acoustic guitar so that it can produce sound through one or more loudspeakers, which are typically housed in a wooden cabinet. A guitar amplifier may be a standalone wood or metal cabinet that contains only the power amplifier (and preamplifier) circuits, requiring the use of a separate speaker cabinet–or it may be a "combo" amplifier, which contains both the amplifier and one or more speakers in a wooden cabinet. There is a wide range of sizes and power ratings for guitar amplifiers, from small, lightweight "practice amplifiers" with a single 6" speaker and a 10 watt amp to heavy combo amps with four 10” or four 12" speakers and a powerful 100 watt amplifier, which are loud enough to use in a nightclub or bar performance.

More often than not, we always find it interesting to see and hear if there is any possible way an entry level electric guitar can outshine or even just come close with an expensive guitar model. These comparisons would mainly starts on looking at how they are built, time spent making them, where it is made and components used on the whole guitar. Having those as criteria in mind and as reality of it. So far it is given that it is going to be all in favor of the expensive models by a margin.
A lot of folks really like Squier guitars. In most cases, I'm not one of them. Fender’s economy guitars (Squiers) are cheap, coming in under $400 (often $200 or less), which can be an attractive option for a first-time buyer. However the price difference between a Squier Strat and a real deal Fender Strat isn’t big enough to make up for the quality hit you take when you buy a Squier.
Epiphone's Les Paul series were originally designed to allow the budget crowd to experience this awesome guitar without investing thousands of dollars. That's something that hasn't changed to this day. The Epiphone Special II is among the most basic Les Paul designs on offer, making it perfect for beginners. We've chosen this particular guitar because of its neutral configuration which will keep up with you even after you've built plenty of skill.
The Cordoba C7 spruce-top has a natural finish, complete with rosewood back, sides, fretboard and bridge, and the traditional looking inlay that Cordoba is known for. Plus, there are the Savarez Cristal Corum high-tension strings that come with it, which give the guitar its clear, clean sound. Of course, you might want to change to another set of nylon strings, should you wish it, depending on the sound you truly want.
I bought this Fender acoustic/electric guitar about 9 months ago. It has a wonderful rich tone, is easy to play and is beautiful. The grain on the mahogany is dark and beautiful. It lives up to its dreadnought name and can fill a large living room with its sound. The tone is deep, rich and mellow. Strings are separated enough for easy picking. Tuning pegs are of decent quality and once strings are broken in it stays pretty much in tune. Other than putting on some bronze phosphor strings I did not need to set the guitar up. I really haven't played it much with an amplifier so can't comment on the electronics, other than the built in tuner works well. The hardside guitar case is well padded and looks professional. I was a little concerned about buying a guitar over the
You are eligible for a full refund if no ShippingPass-eligible orders have been placed. You cannot receive a refund if you have placed a ShippingPass-eligible order. In this case, the Customer Care team will remove your account from auto-renewal to ensure you are not charged for an additional year and you can continue to use the subscription until the end of your subscription term.
Most of the modern electric guitars are provided with several tones and volume controlling circuits which helps in controlling the string vibration and thus the electrical charge produced. These adjustments are mainly done with the help of knobs provided on the neck of the guitar. Thus, the more the number of electrical circuits, the better the guitar can be adjusted for different sounds.
Another company that dates back nearly a century, Rickenbacker was started by Adolph Rickenbacker and George D. Beauchamp in 1931 with the intention of creating fully electric instruments. Following a long and rocky history that included wild successes (like getting their guitars in the hands of the musicians that played with Bing Crosby) and incredibly tough tribulations (like starting an instrument business at the depths of the Great Depression), the brand eventually sold to F.C. Hall in 1953. From that point forward, Rickenbacker flourished as one of the most iconic brands both in the looks of their instruments and their sound. George Harrison, Paul McCartney, and John Lennon of the Beatles all played Rickenbackers at one time or another. Additionally, Chris Squire of Yes, Tom Petty, Pete Townsend of the Who, and Glen Frey of the Eagles are all Rickenbacker signature artists. Like tech giant Apple, however, Rickenbacker doesn’t give their endorsers anything for free nor do they ask for the advertising, making them an even more admiral brand as a result.
Its the type of clipping you would expect to hear from a tube amp that been naturally gained up by cranking the volume levels really high.  Some players refer to this sound as Crunch.  These Overdrive pedals, such as the famous Ibanez Tube Screamer, can also be doubled up to give two gain stages:  Slight Crunch and Creamy Velvet Lead.  They sound as good as they might taste, if they were flavors of cereal or ice cream.  Many players found their tone by using two overdrive pedals back to back.
In Chicago in the sixties, "the rules had been laid down" for young, white blues bands, Mike Bloomfield told Rolling Stone in 1968. "You had to be as good as Otis Rush." That wasn't easy. A Mississippi native who moved to the Windy City in the late Forties, Rush was a fearsome electric guitarist – with a grittytreble tone and lacerating attack, like a gunslinging cross of Muddy Waters and B.B. King – as well as a knockout songwriter. Along with guitarists like Magic Sam and Buddy Guy, Rush helped create the more modernized, R&B-influenced approach to Chicago blues that came to be known as the West Side Sound. Rush's impact on later generations was enormous: His late-Fifties and early-Sixties singles were go-to covers for Led Zeppelin ("I Can't Quit You Baby"), John Mayall ("All Your Love [I Miss Loving]") and the J. Geils Band ("Homework"), while Stevie Ray Vaughan named his band after Rush's lethal '58 lament "Double Trouble."
ARM-SAITENLAGE Die Tremoloarm-Saitenlage kann eingestellt werden, indem 3,0 mm großer Inbusschlüssel an der Schraube (B) an der Tremoloschraube verwendet wird. FEIN-TUNING Auch nach dem Verriegeln der Verriegelungsmutter können Sie die Fein-Tuner verwenden, um Feinabstimmungen zur Stimmung jeder Saite vorzunehmen. Sie müssen alle Fein-Tuner (C) auf Mittenposition des Einstellbereichs stellen, bevor Sie die Verriegelungsmutter festziehen.

Considering that the setup on a factory-fresh guitar might be good or bad (and few music stores bother to do setup on inexpensive guitars), we strongly recommend that you have a new guitar professionally set up, which will likely cost about $50. You can also learn to do it yourself; there are plenty of online tutorials, and even at age 15 I managed to figure out how to set up my first electric guitar with a little guidance from my guitar teacher. It’s a good idea for every electric guitarist to at least learn how to set action (string) height because you will want to adjust this to suit your style and skills as they evolve.
My Carvin SH575 is a semi-hollow body electric. The size is similar to the Gibson 336, but sounds totally different. When you play this guitar you can't put it down, Carvins are made with computer aid wood carving CNC machines the proto-type of the guitar is measured with lasers and programed into the computer so every guitar they make is to the 1000th to the original. The finish and the detail is awesome. It also is wired with hum bucking pick-ups, piezo acoustic pick-up and Roland GK synth guitar. You can get some beautiful hybrid tones from this thing and I never can stop finding new ones. Try one of these out if you ever go to California I think there is like 5 stores around the L. A. / San Diego area, you will see what I mean.
Martin opened its “Custom Shop” division in 1979.[7] Martin built its 500,000th guitar in 1990, and in 2004 they built their millionth guitar. This guitar is entirely hand-crafted and features more than 40 inlaid rubies and diamonds. It is worth an estimated $1,000,000.[8] As of 2007, Martin employs 600 people. Thirteen workers are devoted to quality assurance[citation needed]. In October, 2009, Martin purchased at auction a D-28 that was played by Elvis Presley in his last concert for $106,200.[9]

Many newbie guitarists seek out distortion effects because they don’t like the distortion sound that comes with their amp. Analog distortion and overdrive pedals can help, but it is important to realize they are not magic bullets. Even the best distortion pedal is still at the mercy of the amp you are playing through, and the same pedal will react far differently whether played through a 100-watt tube head or a 40-watt solid-state combo.

That’s not all modeling processors can do. In addition to offering guitar and amp models, most guitar modeling processors have libraries of the kinds of effects you would get from individual pedals—reverb, echo, chorus, overdrive, distortion, fuzz, etc., as well as integrated drum machines with scores of preset rhythm patterns to help your practice. You can run several effects simultaneously, combining them to create your own unique tonal palette. Most modeling processors now have USB connectivity, some even with two-way audio streaming, for use as interfaces in direct computer recording.
Entitled Fine Electric Instruments, the 1964 1965 Fender catalogue was circulated from mid 1964, and despite being just eight pages long, contained a large number of guitars, amplifiers and other instruments. This was the first catalogue to show the new Fender Mustang guitar, which was available in normal or 3/4 scale at that time. This catalogue was included in the 1964 annual guitar issue of Down Beat magazine (July), massively increasing the potential readership, both in America and worldwide.
: I own a Decca guitar, it is what I learned to play on many years ago. From what little I have gathered about them they were an order by mail brand, and you could only get them from a catolog such as Sears & Roebuck. I havent been able to find a price for them or any ifo on what catalogs they were from. Mine has a Ernie Ball Musicman-like peghead (4 one side 2 on the other) and has a metal pick guard with 2 giant switches which seem to have no effect on tone. It has a brown & yellow sunburst paint job (ewwww).I thought I possibly had the only one in existence, lol, guess not.
By the mid 1990s Korean instruments were rising in price as Korean labor rates and other costs went up. Many Korean and Japanese companies set up factories in Indonesia to take advantage of reduced costs there and Fender set up their Mexican factory to take advantage of reduced labor rates in a setting very close to their USA factory. With modern CNC equipment and Korean and Japanese ownership and management, it was possible for Indonesian factories to very quickly turn out good student- and intermediate-grade instruments. In my experience, however, none of the Indonesian products rival the quality of the better Japanese or Korean guitars. The new Mexican Fender guitars give excellent "bang for the buck" and in many cases play and sound better than the later CBS-made American Fenders.
Dobro – we’re still in Dobro territory here, not National – quickly followed suit in 1934 with the Dobro Electric Resophonic guitar. This was basically a wood-bodied Dobro resonator guitar with a Stimson pickup just in front of the handrest. Unlike the All-Electric, this had the poles perpendicular to the strings. This also did not especially go over, and dropped from sight before the year was up.
this is a norma guitar. i think from the late 1960's to maybe 1970estate find. has scratches in some placeshas two on and off button in white they push in real easy. theres a rhythm, and solo button theres two knobs bellow.theres only 3 strings on it. theres three missing part off the r is missing on the norma. i have no equipment to test it to see how it sounds it seems ok when i play with what strings i have on it.please check out all the pictures for better detail selling as is no returns... more
After the lawsuit Hoshino Gakki abandoned the strategy of copying "classic" USA electric guitar designs and moved to the popular superstrat era in the mid-1980s. The newer Ibanez models began incorporating more modern elements into their design such as radical body shapes, slimmer necks, 2-octave fingerboards, slim pointed headstocks, higher-output electronics, humbucker/single-coil/humbucker pickups, locking tremolo bridges and different finishes.
Some great IR's by Redwirez are available for free at their website as some kind of 25th anniversary thing, and if you use windows you can use VSThost as your "DAW" although all it does is host plugins. It's great because it loads so much quicker than a full DAW and doesn't have all the tricky options that just distract you from playing guitar. Like a real amp, it's plug-n-play (after setting it up, of course--- you'll want to set the sample rate to 192khz so that you can get ~8000 samples a sec with oversampling at 4x on each plugin). It can record, too, so it's a really easy, simple solution. Of course, you'll need a real DAW to mix and master.
A lot of amateur guitar players are tempted by the ‘cut’ of a high treble sound that gives their notes definition above the cacophony of the rest of the band. They become so accustomed to this sound that they lose sensitivity to its harshness. Treble becomes the ultimate weapon in their arsenal for the volume war, but to the listener, all they hear is a headache, aka bad tone.
My very strong opinion is that you should find an experienced guitar player, who plays in the style that you aspire to.  Tell them very clearly that you want help finding a beginner guitar that is in good condition and is easy to play.  Don't worry about resale value, looks, brand prestige, etc..  Get that person to help you find something that you can afford.  This is especially true for acoustic guitars (easy to play electrics are easier to find).  This might very well be a used guitar.  Try hard not  to buy a guitar because a salesperson told you it was a great beginner guitar and that it would be easy to play -- unless you really, really trust that salesperson.  It is true that the more money you are willing to spend then the easier it will be to find a guitar you can easily learn on but there are cheap guitars out there that will fit the bill.
Straight out of the box you have over 68 on-board digital effects, 75 custom designed factory patches for iconic sounds, 5 amp emulations and 5 cabinet emulators, so you’re not going to run out of choices on stage or in the studio. In addition, you have access to the Guitar Lab software app that allows you to download new stomp boxes and patches regularly.
Dismantled Fender Telecaster neck pick-up, showing the exposed enammeled, very fine, copper wire, wound on a bobbin around 6 magnets sitting below each string. From Mojo Pickups - 50's Telecaster Rewind. In case you are wondering the metallic case (used to be high-chrome content alloy) acts as a hardware low-pass filter, dispersing the magnetic field of the high frequency vibrations of the string across all 6 poles, but allowing long wavelength, low group velocity, bass frequencies to be captured relatively unhindered— the reason for this is quite complicated and the subject of a solid state physics class which we will not go into here.
Treble is really a form of gain boost that must be considered while gain-staging our signal path. With good tone, a note should ring like a bell, not slaughter like a machete, and that is accomplished by shaving some attack off the waveform and rounding off the frequency response. A bit off rollback on the tone knob takes you into the ballpark, along with your amp settings (I have a dedicated treble-cut on my AC30 that is necessary to tame my telecaster). Once I am in the ballpark, I use the volume knob to fine tune, and personally I tend to let it be from there, relying on a gain-boost pedal to lift my sound when necessary without altering the tone.

The FX325A is one of the most popular Yamaha acoustic electric guitars especially due to its quality sound and affordable price. This model is suited for both beginners and experienced musicians. With a spruce top and Nato back and sides, this full-size dreadnought is both rich-sounding and durable, able to offer years of enriching musical experiences.

Synthesizer: Plug your bass guitar into a synthesizer pedal and you can access four different waveforms (saw-tooth wave, square wave, pulse wave, or your own bass wave form) that give you a wide variety of synth tones, each of which can be tweaked in several different ways. Some synth pedals offer a hold function that continues to play the tone as long as you depress the pedal, allowing you to play other musical phrases over the tone that's being held.               

We're proud to say that our best assets at Guitar Center Forth Worth are our people. When you come in for a visit, you'll find that our staff aren't just friendly folk - they're also experienced musicians. We know our way around all our new and used instruments and accessories, which is why we've earned the trust of Texan guitar slingers from the famous to the casual. If you're into percussion, you'll also love our impressive vintage drum collection here at Cowtown. Drop by for a face-to-face chat about all we can do for you, or feel free to give us a call at 817-423-3800.

• Fade to Bleak: Since there are no pickups, juice or amps involved in acoustic guitar playing in its purest form, string composition – which affects how a string responds to being struck and the retention of tonal qualities – is particularly important for acoustic guitars. Bronze, phosphor bronze and coated strings tends to be the preferred varieties, ascending in price. Bronze strings start out the brightest, but lose their high voices relatively quickly. Phosphor bronze offers a darker tone, but still with a clear, ringing top and the phosphor allows the strings to produce their optimum sound longer. On acoustic guitars, coated strings trade a longer life for less brightness, but good warmth and presence.

In 1978, Michel Chavarria, guitarist, singer and songwriter for French band Madrigal, decided to create a guitar shop with his friend Daniel Delfour. The shop was on a street called "rue de Laganne," which inspired the name Lâg. Like in many other cases, the small business started as a repair, setting and customization shop before creating its own models. Due to the quality of their instruments, they sell custom-made guitars to French and international musicians like Jean-Jacques Goldman, Phil Campbell (Motörhead) and Keziah Jones. Among the best-known models we have the Arkane (a Super-Strat available with different pickup combinations) and the Roxane (with Gibson-like humbuckers).
Three full steps from standard tuning. Used by Dream Theater, Adema, Asking Alexandria on From Death to Destiny and The Black, Boris, Cannibal Corpse, Morbid Angel (on several songs starting with their album Covenant), Father Befouled, Sepultura, Jeff Hanneman of Slayer (on "War Zone" and "Here Comes the Pain" from God Hates Us All and "Not Of This God" from World Painted Blood. Kerry King used a 7-string for those songs), Mutoid Man (Stephen Brodsky started using the tuning during the recording of the Helium Head EP to fill in the low end of the sound, in an attempt to make up for their lack of a bassist at the time), American Head Charge, Nickelback (on "This Means War" and "Gotta Get Me Some" from " Here and Now" and Nevermore (when band switched to 7 strings).
I am a giging, solo acoustic musician from Ohio, performing in Western NY, Buffalo. I only had Acoustic Electrics, 6 and 12 strings until I bought my first Godin A6 Ultra. (Acoustic and Electric Pick-ups). The A6 was impressive in it's own right, so I started looking at other Godin products, and ran into a 5th Ave Kingpin 1. Acoustically it was a 3 star, as I have a couple of Taylors and an Epiphone Masterbuilt that this guitar is no match for unplugged. HOWEVER !! This guitar was designed to be plugged in, and the Tone and ease of Play come shining through when the p90 is in the loop.
* The guitar comes with very light bendy strings. This is probably due to market data that tells Epiphone that the bulk of buyers for this guitar are teen Guitar Heros who think that string bending every note is an essential aspect of shredding and wailing. If you plan to put heavier strings on the guitar (like 12-51s for example) for jazz or other styles of music then you will probably need a truss rod adjustment to compensate for the added tension. If you don't know how to do this, ask someone who does. You can ruin a guitar, permanently, by being too aggressive with a truss rod adjustment.

First off, I would like to say I had a lot of fun building this. Also, my hat goes off to the person that hand wrote all the tiny labels on the parts. With that being said, I couldn't get it to work. No sound at all, and only the light came on when I hit the switch. Now the fact that it didn't work could totally be an error on my part, but who knows. Now what I didn't like about this product is this: the casing is pretty small, so everything is pretty cramped (which may also contribute to why I wasn't able to get this to work, although, if you read other reviews, which I recommend for further useful information, some managed just fine), some pieces were mislabeled (There is a review that sorts this out), and the directions aren't very clear...well I thought they were clear enough, but look where that got me, so be ready for that. So 3 stars for fun, good price, and faster than expected delivery.

A small number of bass units do not fit into the "combo" amplifier, standalone amplifier or separate speaker cabinet categorization or typologies. Some bass amp combos have a removable amplifier. With the amplifier unit taken out of the combo cabinet, the user then has an easily portable amp head (which can be taken to a recording studio for use as a preamp, to lay down bass tracks) and a separate bass speaker cabinet, which could be used with another bass amp head. As well, some amp heads have a small built-in speaker which produces enough sound so that it can be used as a practice amp, so that the bassist can practice when she/he has the head, but not the speaker cabinet. This way, a bassist in a touring band could practice electric bass using her amp head, even if her speaker cabinets were still locked up in an equipment van.


New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition

Maton Guitars - Australia's leading manufacturer of Acoustic and Acoustic / Electric Guitars. Until the late 1930's the Australian guitar manufacturing industry was virtually non existent and good quality guitars were hard to find. The best guitars, it was well understood, came from the U.S.A. Bill May, a Melbourne born jazz musician, woodwork teacher, and luthier, decided to change all that.
Electronics installs are one of my favorite jobs here at the shop and this project was one of the funnest.  Installing a Clapton pre-amp is more then just a quick wiring job because of the surface mount board.  The board needs to be routed into the body underneath the pickguard.  Setting up the router is the most time consuming part of this job and once the routing in complete the actual wiring takes only a few minutes.  The guitar was then topped off with a fret level and setup. -Evan
Like 39% of the people said, they are simply the worst. The first guitar I owned was the Ibanez Gio, I thought it was amazing. I play it every now and then, but not too much anymore. For its price, I think it is the best starter guitar, 10 times better than any first act. I owned a first act, it was the worst guitar of all time. Me finger killed after playing it because the strings are so hard to push down, the frets don't even stay attached to the guitar. All beginner guitarist, don't get first act.
However, John Leckie states an interesting preference for an SM58 and U67 rig instead: "SM57s tend to be that little bit brighter than the SM58, which really isn't what you want when you're miking up an electric guitar amp. You really want to pick up a flat signal, an 'unstimulated' signal I suppose is the word... The U67 gives you the warmth and a broader sound."

Australian singer Frank Ifield also owned and used a Maton guitar, which he later had fitted with a custom-made scratch plate, made in the shape of a map of Australia. Frank gave this instrument to his guitarist Ray Brett when he returned to Australia, and it has been featured on an episode of the BBC programmeAntiques Roadshow. Although these guitars are now normally worth around UK£2,000, expert Bunny Campione valued Ifield’s guitar at between UK£10,000 and UK£15,000, because Ifield had used it in songs featured in a compilation album alongside The Beatles‘ first two singles.[2]
The original switch configuration used from 1950 to 1952 allowed selection of neck pickup with treble tone cut in the first position (for a bassier sound), the neck pickup with its natural tone in the second position with no tone, and in the third switch position both pickups together with the neck pickup blended into the bridge, depending on the position of the second “tone” knob. The first knob functioned normally as a master volume control. This configuration did not have a true tone control knob.[2]

I am an SG player through and through. I own a bunch of them- mostly from the initial run of SG Special Faded with the moon inlays, because that particular run felt right to me. I am looking to have a custom SG style guitar made, but I don't know of any builders who make SGs. Can anyone tell me a boutique or custom shop builder who does SGs? Thanks!


Straight away meeting the essential criteria and tonal platform for a good small solid state combo amp for practicing at low volumes with a pocket friendly price tag is Orange Crush 20RT. This dual channel 20 watt guitar amplifier that also comes in a 35 watt version is the upgraded model of the well received Orange Crush 20 for having a built-in spring reverb effect and a chromatic tuner which are the kind of features great for daily use.
As Jay Verkuilen, has already noted here (no pun intended!), be careful not to hammer too hard on the unplugged guitar as you can be fooled into thinking you have to play much harder that you really do. Fretboard exercises & scales, practicing chord forms, and the like while unplugged is beneficial to your playing, "muscle memory," and aids your relationship with your housemates and neighbors.
So here we are at the end of our journey (well, probably not yours). Maybe you have found the best guitar practice amplifier from this list and cannot wait to buy it or maybe you still want to have your options. BUT my point is that starting with an amplifier for practice is a great idea. Not only will the amp serve a very particular purpose it was made for but you will also save quite a lot of money. For instance, most amplifiers under $100 are great for practice so you can check out our list of the best cheap amplifiers for beginners. And while I know a lot of people don’t like the idea of “cheap” being in the same sentence as their instrument or equipment, the thing is cheaper does not necessarily means bad. Is a $100 amp going to win over an amplifier in the best amplifiers $1000 list? Probably not, but as I already mention the best “objective” amplifier (or what brands and people deem to be the best at the moment) is not always a good option for everyone. That is especially a case with someone who is just starting off their journey into the world of music, amps, guitars and everything of that sort.
The iconic Les Paul Standard is celebrated by the world’s greatest musicians as the standard for perfection in the world of electric guitars. The new Les Paul Standard features the popular asymmetrical SlimTaper neck profile with Ultra-Modern weight relief for increased comfort and playability. Impeccable looks are highlighted by the powerful tonewood combination of mahogany back and carved maple AAA figured top. BurstBucker Pro humbuckers provide modern and classic tones, while immense tonal variety from comes from 4 push-pull knobs. Includes hardshell case.
Description: Body: Mahogany - Body Construction: Solid - Neck Attachment: Set - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 22 - Inlay: Block - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Diecast, Gold, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Black
Electronics kit building kind of fell out of favor during the computer age as the home based technology enthusiasts moved to assembling PC’s, and software development. But home brew electronics has enjoyed a resurgence in recent years in what is now called the maker community. Internet electronics stores such as Adafruit and Element 14 are enabling 21st century geeks to build anything from simple circuits to complex embedded computing projects. These sites provide documentation, tutorials, video channels, and of course, a store, where you can purchase the tools and components required to internet enable your toaster, or feed your cat from the couch.

Thanks for this explanation. I have built a few electric guitars, but they have been in the Gibson style with two humbuckers. I am now working on a guitar with an HSH configuration, so for starters, I needed to understand the basic 5 way switch, which if you just looked at it, it makes no sense. Now I see that the wipers of each pole are on the opposite end of each side.
In 1958, Gibson updated the Les Paul yet again. The new model retained most of the specifications of the 1957 Goldtop, including PAF humbucker pickups, maple top, tune-o-matic bridge with a stop tailpiece or Bigsby vibrato tailpiece. The most significant change in the new models was the finish. The Goldtop color used since 1952 was replaced by the Sunburst finish already being used on Gibson’s archtop acoustic and hollow electric guitars, such as the J-45 model. To differentiate from the earlier Goldtop model, the new Les Paul was referred to as The Les Paul Standard. Original production of the standards lasted from 1958 to 1960. Only 1,700 of these early models were made and have subsequently become highly collectible.[note 6] Original production ended when, in 1961, Gibson redesigned the Les Paul to feature a “double cutaway” body, which has subsequently become the Gibson SG. Due to high demand, Gibson resumed production of Les Paul Standards in 1968. Today, the Gibson Les Paul Standard has BurstBucker pickups on the Vintage Original Spec models and Burstbucker Pro on the lower end models bearing the ‘Standard’ name.
There's just no getting around the Martin brand when there's talk about good acoustics. And since we're talking about the best of them, it's not surprising to find their name filling up multiple slots in this list. The Martin DRS2 acoustic guitar is special because it gives us a true all-solid wood body Martin acoustic guitar - at a very reasonable price point, in the dreadnought shape that the company themselves developed.

My band has two guitar players. One often plays acoustic while the other one plays an electric guitar. There has always been a problem balancing the volume and the frequences. While both guitars play on a clean sound it sounds fine but when electric guitar changes to distorted, overdriven or crunched sound then even at a low volume the acoustic guitar is almost unheard. Is it a common problem or particulary our local one. Any solution?
The Fender Stratocaster, or Strat® (as it's been referred to affectionately for decades), has become a favorite for players of all genres. Introduced in 1954, the Stratocaster ushered in a new era of guitar design and has been instrumental in the development of modern music as we know it. Like its older cousin, the Telecaster, it features single-coil pickups. But rather than just pickups at the neck and bridge, it has a middle pickup and five-way selector that allows for even further in-between tonal variations. Along with being the first solid-body electric to have three pickups, it was also the first to have a self-contained vibrato system.
Open Loop Gain: Feedback Solid-state amplifiers are inherently nonlinear. They have a very large ‘open loop gain’ approx 20,000. The amplifier output is (feedback) to the comparator input to reduce the gain to approx 50. Therefore 99.9% of this feedback corrects all instability and non-non-linearity of the amplifier, as explained in amplifiers. The speaker also acts as a large microphone. All non-linear movements and vibrations within the speaker cone, (caused by reflected nodes, chaotic resonances etc) of which there are many, are regenerated back into electricity by the voice coil. This re-generated signal from the voice coil is inadvertanetly fed-back to the solid-state amps comparator input, and re-amplified back to the speaker as recycled distortion.
Remember how we said that Ibanez has some pretty rad entry level guitars? Well, Ibanez GRX70QATBB is one that is worth mentioning. It belongs to the legendary GRX family, and brings a well-balanced performance for the money. I actually bought one of these for my nephew, and had to put it through its paces before I handed it over. It’s a bit rough around the edges, but one visit to a guitar shop took care of that.
There is a weekly newsletter that features lessons from different genres and difficulty levels. Whenever I open that newsletter I feel compelled to try out that featured lesson. I believe that this is a big reason why my guitar playing is improving so quickly. I am continuously trying out different styles and techniques and I get better overall while doing this and having fun.
Fender California Coast Series acoustic guitars are already being used across multiple musical genres by top alternative, indie, punk and grunge artists/bands, such as: Culture Abuse, The Regrettes and Dear Boy, as well as singer-songwriter Aaron Lee Tasjan and guitarist Angela Petrilli – accompanying each on their musical journey toward exceptional artistry.
Drop A in D standard variation - A-G-C-F-a-D: Used by Mastodon on most of their first album (Remission) and on some songs on other albums. Also utilized by Periphery on the song "Zyglrox" as well as "Alpha" and "The Bad Thing." Also used on occasion by Black Label Society, who previously tuned it a half-step up, which Alter Bridge also utilizes on some of their songs such as "Broken Wings", "Come to Life", "I Know it Hurts", "Still Remains", "Breath Again", and "All Hope is Gone." Creed, Architects, and Sevendust all use this tuning tuned a half-step down on their songs "Bread of Shame", "Early Grave", and "Home" and "Chop" respectively, with the latter also tuning down a full step for the songs "Death Dance" and "Not Today". Danish industrial metal band Raunchy used this tuning tuned one and a half-step down (F#-E-A-D-f#-B) on the song "Dim the Lights and Run" from the album A Discord Electric. Wage War also utilize this tuning one whole step down for songs like "The River" and "Spineless" off their album Blueprints.
Zen guitar is not about scales and memorizing chords. Instead, it is a masterpiece of why to play guitar, helping you get through the times where learning guitar gets frustrating, and believe me, it will at some point get frustrating. But if you can get through that and push on, you’ll be rewarded with mastery of an instrument that will give you personal fulfillment and a lifetime hobby that brings achievement and satisfaction.
Today, Van Halen is one of rock’s most influential and imitated innovators. As unpredictable and flamboyant as Hendrix, Van Halen has had an unmeasurable impact on the guitar community. By the mid Eighties, his self-described “brown” sound, over-the-top techniques (including two-handed tapping), and revolutionary trem-bar effects inspired a generation of aspiring guitarists who bought the one-pickup, one-volume-knob, Floyd Rose–equipped Strat-style guitars that Van Halen made famous.

As the author of the article, I don’t use an Axe-Fx, but a $250 Fly Rig. But if I want to talk to an expert on modeling, I wanted to ask the company that knows it best. Sure, you have to take in to consideration a PA, but you have to do that if you own an amp too, since proper sound sends keeps the volume lower on stage to send everything through the PA.
The fourth type of system employs string-through body anchoring. The strings pass over the bridge saddles, then through holes through the top of the guitar body to the back. The strings are typically anchored in place at the back of the guitar by metal ferrules. Many believe this design improves a guitar's sustain and timbre. A few examples of string-through body guitars are the Fender Telecaster Thinline, the Fender Telecaster Deluxe, the B.C. Rich IT Warlock and Mockingbird, and the Schecter Omen 6 and 7 series.
×