DRILLING THE NECK HOLES ON THE BODY Before you do this you can carve down the back of the neck area if that is something you were going to do. If you are just going to leave it flat then that's ok too. The first step if you are using furreles is to map out where you want to place them and then mark the center of the hole where the screw will go. Then take your forstner bit drill enough to fit the furrele inside. Usually you can tell how deep to go if you drill a little at a time, and place the furrele in it to see if it is just low enough in the hole not to see the top of it if you look at the body horizontally or it is flush with the wood. After doing this you can drill the holes for the screws. Use a bit that has the same circumference as the screw including the threading so when you put the scre into the hole it just passes through with out you having to screw it in. Drill in the indention that was left by the tip of the Forstner bit, keeping the drill as straight as possible.

Providing all of the necessary features expected in a quality electric guitar at a budget-friendly price, the Epiphone Les Paul Special II is perfect for those just beginning their musical journey or the seasoned guitarist looking for an everyday guitar for practice. The 650R humbucker pickups combined with the open coil design deliver strong and sustained tones. As seen on all Epiphone guitars, the Special II has over 500K potentiometer for both tone and volume, and a toggle selector with a 3-way pickup to focus in on the clarity of the sound and decreased excess humming. The body and neck are made with mahogany, while the fretboard has dot inlays within the rosewood design. String changing is also made easier due to the stopbar tailpiece, which helps to add more sustain in sound when combined with the LockTone Tune-O-Matic bridge. With all of these features at such a reasonable price point, the Epiphone Les Paul Special II is a strong contender included on this list.
Guitar effects and the boxes that generate them have married theory and practice, history and material, content and form. Such strange logics, inherent to all of these simple devices, radiate sincerity in their transgressive sounds. Or put differently, those “unmistakable sounds,” which can enchant an entire generation, are not entirely intentional, but are born from the accidental collisions between transistors, tubes, wiring, and luck.
A pedal itself can have an effects loop, but the most commonly used place is on the amplifier itself. You'll see on most amps (but not all) some form of output labeled as Effects Send or Preamp Out accompanied by an input labeled Effects Return or Power Amp In, respectively. Both sets of outputs and inputs refer to the effects loop that you can add between the preamplifier and the power amp section of your amplifier.

The question is now - do you need the entire bundle? When it comes to the presets, the guitars are all very unique, but because of the mass amount of tone-shaping available once you start twisting and manipulating away there becomes less and less of a distinction — the bundle being over a third less than individually purchasing them doesn’t help the decision making factor at all.   
There aren’t a lot of professional reviews of inexpensive amps, but James at Guitar Verdict raved about the Champion 20, saying, “For an amp of this price, the Fender Champion 20 watt offers a massive amount of value,” and calling it “a hard to beat offering.” At last count it had earned an average of 4.6 out of 5 stars in 595 Amazon user reviews and earned an A for review integrity from FakeSpot.

Acoustic necks are usually listed as 12- or 14-fret necks. This number refers to the number of frets above the guitar body, not the total number of frets. On a 12-fret neck, the 13th and 14th frets will be on the body, and, thus, harder to reach than on a 14-fret neck, where they are extended beyond the guitar body. If you have small hands, look for an acoustic guitar with a smaller diameter neck.

Obviously, what I've done is to give myself a choice of three different sounds--a close, ballsy sound, a mid-range room sound, and a more distant room sound. By setting all three mics up at the same time, putting them each in a different input, and assigning them all to the same track on tape, I've given myself the option of having any one of those sounds immediately available to me, or a combination of them.
Bass amp speaker cabinets are typically more rigidly constructed, with thicker wood and more heavy bracing than those for non-bass amplification. They usually include tuned bass reflex ports or vents cut into the cabinet, for increased efficiency at low frequencies and improved bass sound. Preamplifier sections have equalization controls that are designed for the deeper frequency range of bass instruments, which extend down to 41 Hz or below. Bass amplifiers are more likely to be designed with heat sinks and/or cooling fans than regular guitar amplifiers, due to the high power demands of bass amplification. They are also more commonly equipped with audio compression or limiter circuitry to prevent overloading the power amplifier and to protect the speakers from damage due to unintended clipping in the power amp.
I've been a guitar player for decades but only recently became serious about working on my instruments. In my research, I’ve found hundreds of articles about instrument repair, and while many are fantastic and chock full of information that’s invaluable to musicians, a lot is impractical or requires more space or specialized tools than most of us have. Plus, some repairs, such as fretwork, nut replacement, under-saddle pickup installation and finish repairs are best left to professionals.
A 6 stringed guitar, black satin in color. It is gloss finish and comes without a case. The body is made from Mahogany and the neck from the Flamed maple. The guitar consists of tone,volume and 3 way pickup switch. It was introduced alomost 20 years ago and includes all the charm present in its cousins from USA . The device can be acquired with as little as INR 19,755  and more details can be found at:
Delay/echo: Delay/echo units produce an echo effect by adding a duplicate instrument-to-amplifier electrical signal to the original signal at a slight time-delay. The effect can either be a single echo called a "slap" or "slapback," or multiple echos. A well-known use of delay is the lead guitar in the U2 song "Where the Streets Have No Name", and also the opening riff of "Welcome To The Jungle" by Guns N'Roses.[86]
1939: The #1 brace inside near the neck block changes from 5/16" wide to 1/2" wide, making it roughly twice as wide. This happened at the same time as the popscicle brace addition. The neck block thickness was also reduced by 1/4". About the same time neck width reduced from 1 3/4" to 1 11/16" at the nut, and the bridge spacing reduced from 2 5/16" to 2 1/8".
Wah and EQ manipulators work best before distortion and overdrive devices, near the start of the signal chain. The one exception is the Fuzz Face or any vintage-style fuzz, which needs to be slotted in before the wah. Try it – put your wah before and after your distortion and listen to how different it sounds. Also, compressors tend to work best when placed before drive effects.
Since National had applied for a patent on the single cone (US patent #1,808,756), Dopyera had to develop an alternative design. He did this by inverting the cone so that, rather than having the strings rest on the apex of the cone as the National method did, they rested on a cast aluminum spider that had eight legs sitting on the perimeter of the downward-pointing cone (US patent #1,896,484).
To build an electric guitar, start by cutting out the guitar body from a piece of wood like maple or swamp ash. Then, bolt a pre-made neck onto the body and attach the bridge. Next, install the pick-ups, volume control, and guitar cord. Finish by putting your strings on the guitar and testing out your instrument. If you want to make the process easier, you could try purchasing an electric guitar kit.

Electronics.  If your guitar comes with a pickup system (either from the factory or aftermarket) we will test it before it ships.  Poor sound, uneven string balance, and just plain component failure is all checked & corrected so you don't have to fool around with it. If your guitar's system requires a battery inside the guitar, we may remove it prior to shipping.
When it comes to buying an electric guitar there are a lot of options available, and choosing one can be confusing. This guide will help you understand the basic differences in electric guitars so you can make an informed decision. And remember, we’re here to help with friendly Gear Heads available at 1-800-449-9128 who can guide you to the electric guitar that best meets your needs.
There is traditionally a gap between how we enjoy the sound of our guitars and the way they’re represented plugged in. Enter Yamaha, a leader in stage-ready acoustic technology for decades - and in the A5R ARE, it may have just offered us a very desirable solution. The A5R''s rounded fretboard edges offer an enjoyable playing experience that mimics the feeling of guitars that have been played in to a degree and it has an ethereal quality in the high ranges, even though some treble resonance is traded with the lower action. The A5’s resonance and bright balance is a fine showcase for the clever SRT2 preamp - we actually couldn’t dial in a ‘bad’ sound on it because the treble and bass controls mirror the natural subtlety of the pickup/mic dynamic design. An electro experience that captures the sound of an unplugged acoustic? The SRT2 is one of the closest to get there yet. An update that marks the A Series out as an essential consideration for players who rely on a consistent and controllable stage sound.
We supply different variants of Electric Bass Guitar, which is just an extension of the Electric Guitar. The only difference between the two is that the former comes with a longer neck and scale length. It also comes with an option of 4, 5 and 6 strings. The four string bass guitar is tuned in a way similar to tuning a double bass guitar. It is capable of
Despite the fact that there are many great beginner guitars out there, Ibanez holds the title of owning starters designed specifically for metal. The way they have achieved this reputation is quite ingenious. They have delivered the same body style shared with their higher-end models. Ibanez GRX20ZBKN is a good example. It is a basicguitar that packs a mean punch.
In late 2012 I decided that I had all the modern guitars I needed. I’m not gigging much, just writing and recording. There were a couple of vintage guitars I was interested in. A Vox teardrop, especially the Mark IX, and the Fender Coronado. The Voxs turned out to be too expensive for me, especially the Mark IX, which was a 9-string beast meant to sound similar to a 12-string. Those are very rare and priced out of my range. The Coronado, I might be able to afford one day, but I’m not as interested as I was. The new reissues sell for about $700, but they’re different from the originals in several important ways.
During World War II, instrument manufacturing at Gibson slowed due to shortages of wood and metal, and Gibson began manufacturing wood and metal parts for the military. Between 1942-1945, Gibson employed women to manufacture guitars. "Women produced nearly 25,000 guitars during World War II yet Gibson denied ever building instruments over this period," according to a 2013 history of the company. Gibson folklore has also claimed its guitars were made by "seasoned craftsmen" who were "too old for war."[13][14]
While a straight DI approach can work for clean sounds, simply plugging a guitar into an overdrive pedal and then routing the output of the pedal into your recording system will sound unnaturally thin and raspy because there are no speakers to take away the unwanted high end, but that hasn't stopped some people using it as a 'trademark' sound! For a more conventional sound, a speaker simulator is needed to filter out the unwanted higher harmonics. A passive speaker simulator, such as the original Palmer Junction box can be placed directly after an overdrive pedal or a regular guitar amp preamp output, but it will need to be recorded using a mic input rather than a line input (passive filtering always results in a reduction in level). Active equivalents (usually battery or phantom powered) are also available, which may offer a greater range of tonalities.

An instrument unlike any other, the electric guitar gives musicians a feeling and hands-on experience that's nearly indescribable. Even with the same electric guitar, no two players sound exactly alike. Every nuance of the player's hands comes out in the electric guitar's tone, both in fretting and plucking the strings. The best players master not only command of the electric guitar, but also its interaction with their effects and amplifier. It's difficult to imagine a world without the combination of the electric guitar and amplifier, yet it's still relatively new in music. By the turn of the twentieth century, it only made sense that the popularity of the guitar would soon be combined with the onset of electronics. Over the past 75 years, the electric guitar has established itself as one of the most iconic, unforgettable instruments in the world. From jazz and big band to rock 'n' roll and funk, popular music would be drastically different today had it not been for the electric guitar.
Audiffex Guitar Pedals was one of the first professional guitar software packages, with its original version released more than a decade ago. It has since been upgraded but continues its legacy of providing stompbox effects in software form. The latest version is an all in one guitar effects software package - which includes 36 plug-ins that also works for bass, vocals and other instruments. Features include consistent interface with all effects having similar controls, modular plug-in configuration for easier and flexible routing and intuitive preset management. Current retail price: $49

The Wave is a versatile stand-alone, tube driven analog spring reverb unit kit. It can be used in front of your guitar amp or as a line-level analog reverb effect for the recording studio. Two controls allow you to serve up a wide range of wetness from just a touch to over the top psychedelia. The "dwell" control adjusts the input signal level driving the tank and the "reverb" control adjusts the level of output reverberations from the tank.
Make your next guitar one of a kind. Every luthier set sold by OregonWildWood is visually unique and distinctive - even sets within the same species vary greatly in color, contrast and figuring. You'll find the largest online selection of guitar woods available - all special within their own right. All are exotic, beautiful, unique and superior. Each set is individually pictured giving you the opportunity to choose the perfect one for your next guitar.
Guitar effects pedals are a great way to get started with electronics. The simplest ones only require some basic skills to assemble. The few parts can be easily obtained, and the minimum of tools required can be purchased quite cheaply. Better still is the gratification from plugging it in for the first time and being able to incorporate a pedal that you made yourself into your music. With the skills you acquire, you can graduate from simple to more complex projects; maybe build an entire pedal board of your own effects. Your friends might ask you to build pedals for them too. What you learn can also be put to use with commercial pedals, as you will better understand how they work, and will be able to repair and hot rod old pedals. If you are interested in working at a repair shop, as a guitar tech, or for an electronics company in the future, your portfolio of home built pedals will be a great advertisement for your skills.
The downside of going electric is that now you have to think about a soundboard, or at least an amp. And no self-respecting guitarist can live without a few pedals to tweak the sound. I mean you only need a volume pedal to control the level, a tuner might be nice, chorus is always appreciate, a nice delay pedal wouldn’t be bad, and you might need a clean boost for those solos. Then again, you might just want to plug straight into the soundboard and just enjoy that amplified acoustic sound.
Theory - These sessions will be devoted to investigating how the fretboard works, how strings and notes relate to each other, what chords are made up of etc. A lot of theory time will be spent reading and analysing diagrams and your guitar's fretboard. This aspect is for understanding how music works on the guitar, to map out the fretboard in your mind so you can later apply the physical techniques with confidence. If you're serious about getting good on guitar, you need time devoted to theory.

Older 1800s Martins are a challange to date (since they don't have a serial number like 1898 and later Martins). A "New York" stamp does not immediately suggest that the Martin guitar is from the 1830s for example. To accurately date pre-1898 Martins you must be familiar design and ornamentation appointments and the changes that took place in each model throughout the 1800s. Most useful though is the stamp, but you can only use the stamp on the INSIDE of the body on it's center backstrip (visible through the soundhole) to date a guitar. And even then you can only date to a period (and not to an exact date). For example if it says on the center back strip, "C.F. Martin, New York", then the guitar is pre-1867. If it says, "C.F. Martin & Co., New York", it is between 1867 and 1897. Note 1860-1890s Martins have a date (year of manufacture) penciled on the underside of the top. Check with a mirror, looking just below the soundhole and between the braces.


You can run up to six of the 112 built-in internal effects within the Boss MS-3 Multi Effects Switcher at the same time and integrate three of your existing stompboxes into that sound too. So, to say there’s a world of options at your feet is an understatement. You can use it with your hybrid MIDI gear and utilise it to channel switch between amps too.
Learning to do your own setup is just as important as learning how to play. If you feel uncomfortable doing it, go to a pawn shop and spend that 50 bucks you would have spent on a setup and buy a hack bass instead and pratcice on that. You can also practice your soldering and anything else without fear of ruining it and end up saving a ton of money in the long run!
Just in early Red Lable Nippon Gakki FG150 in excellent Vintage Condition CLEAN!.............. rare to find one pretty, then to be straight, then sound deep and loud like this one sounds but to have great action too its intonation is dead on upgraded nut & saddle & strings to Martin Marquis 80/20 - 12s This is a pleasure to play with wonderful tone its like 45 years old and the tone woods always sounded great but even better now its the one!!!... serious collectors guitar and is Recording worthy... shes somthing special. to buy it contact Joe: JVGuitars@gmail.com .
Blanket’s richly interwoven cinematic ambient rock has rapidly evolved since last year’s debut EP Our Brief Encounters. We have had a sneak preview of their new material and can confirm it is a sizeable slab of Big Rock that will induce palm-sweat from fans of Lonely The Brave, Nordic Giants and This Will Destroy You. Guitarists Bobby and Simon - the duo at the heart of this sound - are masters of catharsis, bonding warm, cascading lines into structures of true grandeur.
Ibanez is a Japanese guitar brand, which is established in the year 1957. They provide Acoustic, Bass Guitars and Semi-Acoustic Guitars at different price segments. The company is owned by Hoshino Gakki. Their headquarters located in Nagoya, Aichi, Japan. They also manufacture amplifiers, mandolins and effect units. They become one of the top ten best guitar brands in India. The price range starts from Rs. 13,299/- onwards (approx). For further details, visit Ibanez.com.
The intonation here refers to the forward/backward position of the individual string saddles. By moving the saddles forwards or backwards, we are actually adjusting the length of the strings. Without going into too much detail, if the string is the wrong length, the positions of the frets will not be correct and the guitar will be out of tune on some of them. Adjusting the intonation is not difficult. All you need is a guitar tuner and a tool to move the saddles forwards or backwards. Play an open low E string and make sure it is in tune (using the guitar tuner).
It’s easy to remove your pickup or pickguard and slide some foam rubber behind the unit. Start with soft foam first, and then increase the density to find the difference you like. Conveniently, the gray foam used in aftermarket pickup packaging makes great damping material: It’s soft enough that you can double it up (see Fig. 1 and 2) to create more pressure on the pickup’s back plate, too. This is a relatively no-frills mod that requires minimal materials and tools.
It was shortly after the debut of the first Supros that National Dobro entered a period of major transition. By 1935, at least, the company had decided to abandon the sunny beaches of L.A. for the freezing winters of Chicago, then the principal home of America’s instrument makers, and not coincidentally, America’s giant mass merchandisers Montgomery Ward and Sears. Both Wards and Sears had been offering National and Dobro resonator guitars since the late ’20s. Being in Chicago had the obvious advantages of proximity to the resources surrounding the business and being next door to the world’s two largest retailers of the day. The move to the Midwest began early 1936 and took almost a year and a half. Throughout most of ’36, the majority of production continued in L.A.
This old Nickelback hit is made up of only four different chords, written in the Key of G. During the verses only use G – C – F to progress, while the chorus of the song will add an Am (A minor) to change things up a little bit. This is a fun song to listen to and play along with, especially since the song is set a slower tempo, especially for a rock song.
Support your local music shops! The Guitar Store is a great spot in a convenient location. Helpful and friendly staff all around. A good assortment of electric and acoustic guitars, amps, and more pedals than you could possibly imagine. No cases full of BOSS Metal Zones either - we're talking real pedals for the pedal enthusiast. They also are great for lessons/workshops and instrument repair. We had been bugging the guitarist in my band for having a noisy output jack for weeks. He took his guitar in, came in during a slow time, and they replaced the jack for him on the spot! Amazing! So while Guitar Center might be your only option to buy that fancy pack of tapered-B 5-String bass strings, The Guitar Store should be your first choice for literally anything else. Check it out! SUPPORT LOCAL MUSIC SHOPS! But they make you leave your backpack at the counter?!? ZERO STARS!!!!! ;-)
Now we’ve got the basics down, let’s have a look at some simple modifiers to the circuit. This article first shows you how to add a “killswitch” to the guitar, then uses the lessons learned from that process to change that killswitch to a volume control instead. Finally, we’ll find out how capacitors are used in guitar circuits and install our first tone control.
Hum in pedalboards is usually “ground loop hum.” You have two paths to ground, your audio ground and your power supply ground. You could use an expensive power supply with isolated grounds. But all you have to do is break one of the ground connections. You could disconnect the audio ground at one end of each of your patch cords. Or better, if you use one power supply, connect the hot and ground to only one of your pedals. Clip the ground wire on all the other pedal connections in your daisy chain. The power connections will then get their grounds through the audio grounds. No more hum

Honeyman-Scott’s solos were concise and economical, getting the point across in only a few measures. His solo on “Kid” is a pop song unto itself that evokes the Beatles’ finest melodic moments, while his three- and four-second bursts on “Tattooed Love Boys” unleash more emotion, fire and style than most guitarists can convey in an extended 15-minute solo.
Amps. When I first plug into an unfamiliar amp, I’ll start by setting all the tone controls to noon, and slowly raise the volume to a comfortable level. If the amp has a master volume, I set it for a good listening level and sweep the gain knob to explore the amp’s overdrive capabilities. I then make small tone tweaks by sweeping each pot up and down and listen to the range they work in, and how they affect the sound from different points in front of the amp.
It’s provided as-is with no support, but it’s still well worth checking out if you’re on a PC. According to the developers, it was born inside an academic research project about the modelling of electric devices, and then applied to the musical instrument field as an evolution of the techniques available in commercial units. Its most important feature is the high precision of the simulation.
The Chord Harmonica consists of two harmonicas hinged together. Together, they are capable of playing 48 chords. They are 23 inches long, and each chord takes up 4 holes. The chord harmonica is used to provide chordal and rhythmic backing in an ensemble, much as rhythm guitar might do. Jerry Murad's Harmonicat's 1947 "Peg O' My Heart" was played on a Chord, with a cleverly arranged sequence of chords that produced the impression of a melody. Hohner's main Chord is known as the Hohner 48, because it plays 48 chords. Hohner from the 1930s to the late 1960s also produced the Polyphonia No. 8, which played 36 blow-only chords, in three rows. The concept failed and is often frowned upon by professional 48 chord players.
Guitar Neck wood Fingerboard Blanks Electric guitar wood Burl Poplar 1pc Walnut Spalted Apple Burl poplar Spalted Maple Olive Spalted Walnut Burl Elm African Mahogany body wood Red Willow 1pc body blanks Plum Red Willow 2pc body blanks Spalted Birch Pear Mulberry Maple Acoustic / Classic guitar wood Flute and Oud blanks Pool Cue wood blanks & Wood Turning Gallery Sold examples Custom Wood Products Binding wood NEW! Gun Stock Blanks
Great Martin Copy from the later 60's This example is a Well Crafted in Japan model with the "orange lable" Nippon Gakki highly collectable now as a great player Martin like player. Great wood...just see the pics WoW! Sitka Soruce Top, Premium AAA Grade Mahogany neck - sides & back...Made by serious craftsmen high degree of skill and well balanced. Nice big Tone as a Martin same type X bracing and is a proven performer. Nicely aged wood and is a wonderful playing 7 sounding vintage guitar equal to many more expensive builders like Martin. This one has a slight stable old top crack as glued and is not an issue anymore...Plays like butta...You will love the sound! .
According to the laws of electromagnetism, whenever an iron coil is moved inside a magnetic field, an electric potential is generated in the iron coil. This arrangement is known as an electromagnet. An electric guitar uses the same principle for generating an electric signal using small electromagnets which is then rectified and amplified to reach an appropriate audible sound level.

Hohner Musikinstrumente GmbH & Co. KG is a German manufacturer of musical instruments, founded in 1857 by Matthias Hohner (1833–1902). Hohner is identified especially with harmonicas and accordions. The Hohner company has invented and produced many different models of instrument, particularly the modern melodica, and most of the harmonicas used by professionals. The company also makes kazoos, recorder flutes, melodicas, banjos, guitars, bass guitars, accordions, and ukuleles (under the brand name Lanikai), along with its one million harmonicas a year.

Description: Body: Mahogany - Body Construction: Semi-Hollow (Chambered) - Top Wood: Maple - Flamed - Neck Attachment: Set - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 24 - Inlay: Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Chrome, Diecast, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: HoneyBurst, Green
For several years now Godin have been producing some of the most sonically versatile guitars available with their combination of regular pickups, piezo pickups and synth pickups built into their higher end guitars. Note that the synth pickups are 13-Pin and compatible with the Roland GR series guitar synths - if you want MIDI you have to first plug into a Roland synth then take the MIDI out from the synth.

Lou Reed has been blowing traditional guitar styles to bits since his Velvet Underground days. A fan of Ike Turner's R&B and Ornette Coleman's free jazz, he created epic bad-trip psychedelia on songs like "Sister Ray." "He was rightfully quite proud of his own soloing," wrote fellow New York guitar luminary Robert Quine, "but resigned to the fact that most people weren't ready for it." As a solo artist, Reed kept on ripping up the rulebook: See 1975's Metal Machine Music, a noise opus that took feedback further than Hendrix could have imagined.


“Move up to Alnico IV and the power rating comes up and the frequency response flattens out – you get a balanced and natural- sounding response from the coils, but not so it’s boosting the treble. The mid-range stays quite constant as well. And then you go to Alnico V, which has the highest power. Then the bass and treble do get boosted and the sound starts to get more aggressive – more ‘rock ’n’ roll’, for want of a better term.
It comes in arctic white, fiesta red, black and vintage sunburst, so there’s a healthy level of customization available. Finally, there are three classic Strat single coils, two volume knobs and a tone knob. Accompanying that is a five-way selector switch, so you can dial in your tone and fine tune it with the knobs. It all comes in a really nice package that will feel really good right out of the box. You really can’t go wrong with a classic like this. 
{ "thumbImageID": "Excel-Series-EX-SS-Semi-Hollowbody-Electric-Guitar-with-Black-Hardware-Black/L10403000001000", "defaultDisplayName": "D'Angelico Excel Series EX-SS Semi-Hollowbody Electric Guitar with Black Hardware", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51438957997383", "price": "1,699.00", "regularPrice": "1,699.00", "msrpPrice": "2,629.99", "priceVisibility": "1", "skuUrl": "/DAngelico/Excel-Series-EX-SS-Semi-Hollowbody-Electric-Guitar-with-Black-Hardware-Black-1438957997383.gc", "skuImageId": "Excel-Series-EX-SS-Semi-Hollowbody-Electric-Guitar-with-Black-Hardware-Black/L10403000001000", "brandName": "D'Angelico", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Excel-Series-EX-SS-Semi-Hollowbody-Electric-Guitar-with-Black-Hardware-Black/L10403000001000-00-60x60.jpg", "imgAlt": "" } ] }
×