With so many guitar manufacturers hot rodding the Stratocaster, it is refreshing to see brands like ESP going after the other popular guitar shape, resulting in the "Super LP" guitar like the ESPT LTD EC-1000FM. This souped up version of the classic single cutaway body combines traditional looks with modern tones and playability, resulting in a fast playing axe that's easy on the eyes, and not too edgy.
For more complete control of preamp distortion voicing, an additional EQ pedal can be placed after a distortion pedal; or, equivalently, the guitar amp's tone controls, after the built-in preamp distortion, can be used. An EQ pedal in the amp's effects loop, or the amp's tone controls placed after preamp distortion, constitutes post-distortion EQ, which finishes shaping the preamp distortion and sets up the power-tube distortion voicing.
Free to use schematics to get started can be had from the web but remember, if you are going to use someone else’s work, either completely or as a starting point for your own design, check first to see what copyright and any other terms are associated with it. If it’s not clear, ask first. There are plenty of open source designs available to use, but schematics, like other written works are covered by copyright law so check you have permission before using them.
EQ can make a tremendous difference in the sound of your instrument. This becomes especially important when playing in a band setting. Your guitar might sound great played alone, but within the sound mix of a full band may need some tweaking. Depending on which instruments are involved, you will need to adjust EQ to help your guitar fit into the overall sound the rest of the band. Using an EQ effects processor can help you dial that sound in more easily and precisely than depending on just your guitar and amp’s EQ controls.
In 2008 Squier released its Classic Vibe series, a series of electric guitars and basses mirroring classic Fender designs of the 1950s and 1960s—each roughly reflecting the hardware, woods, color variations, finishes, body contours, and tonal characteristics of their respective era; Squier states that they didn’t intend the series as completely era correct, but wanted to impart the ‘vibe’ of a classic Fender design—the vintage-quality feel, look, and sound of their first series of guitars in 1982.
Replacing or repairing knobs. Knobs are covers for your pots so you can easily turn them, if any of your knobs are unable to be correctly placed on try due to broken or enlarge holes, place a good amount of tape around the pot's shaft that covers it and try to keep the the knob on the tape. If you cannot do so then you may need to replace your knobs.
I think this is one of the better done tests. Any musical instrument is subjective, so there is no “this one sounds ‘better’”, but having an understanding of how individual components interact in the overall sound is important in a luthier. Too often players are too quick to label one guitar as sounding “good” or “bad” instead of quantifying what characteristics they do or don’t like. Building this sonic vocabulary helps a musician work their way towards their ideal instrument instead of haphazard trial and error.
For my tastes, position 1 on a clean tone can be a bit too boomy. Even if one backs the volume a bit to take the edge off, it doesn't quite suit acoustic-style strumming. Position 2 is perfect for these sorts of things, though. I'd always use it for the small high chords you often find in funk and reggae. Position 2 is also a nice way thinning a distorted tone without it cleaning up too much, like Position 1 with the volume dialled down does. If you have your rig set so Position 1 screams, Position 2 will sing.
Dick Dale is a prominent Stratocaster player, who also collaborated with Leo Fender in developing the Fender Showman amplifier. In the early 1960s, the instrument was also championed by Hank Marvin–guitarist for the Shadows, a band that originally backed Cliff Richard and then produced instrumentals of its own. So distinctive was Hank Marvin’s sound that many musicians, including the Beatles, initially deliberately avoided the Stratocaster. However, in 1965, George Harrison and John Lennon acquired Stratocasters and used them for Help!, Rubber Soul and later recording sessions; the double unison guitar solo on “Nowhere Man” is played by Harrison and Lennon on their new Stratocasters.
Pre-delay on the reverb can help separate it out from the source sound. If your reverb has no controls for pre-delay, you can simulate this using a simple delay on an aux track before the reverb. Decay Settings: Choosing the most appropriate reverb treatment for a song can be surprisingly difficult, especially if you have hundreds of presets to choose from. So, instead of regarding reverb like the glue that holds the mix together, try adjusting its parameters (and in particular the decay time) while listening to the reverb return by itself. If the decay time is too long you'll hear a continuous mush of sound; if it's too short you'll scarcely hear it unless its level is turned right up. Somewhere in the middle you should find a setting that adds rhythmic interest to your song, without overpowering it, making the reverb work for its keep. This is also a useful technique when using several reverbs in a song, to make sure they complement each other. Martin Walker
You'd mentioned that the bridge pickup is substantially louder on Telecasters than the neck. I have an American Standard so the relationship between the two might not be identical but I was able to make the volume levels comparable by raising my neck pickup substantially so that only about a half inch of space remained between the string and the pickup. They're now about equal volume and if anything the front pickup sounds better and more defined as a result.
Position 4 (inner coils, parallel connection): This is similar to position two just inverted. Pole 1 connects bridge pickup coil tap to the output through pole 2. Pole 3 grounds neck pickup coil tap and pole 4 connects neck pickup hot lead to the output. That leaves us with bridge pickup coil from ground to coil tap and neck pickup coil from coil tap to hot lead. Again, they are paralleled.
Tube technology is very much alive in today's digital age, thanks to guitarists who just could not let go of the sound of the past. Even with amp modeling inching closer and closer, there's just no replacing the warmth and organic response of tube amps, especially when recording. Still, there are practical drawbacks with this old technology, mostly due to its fragile nature and extra parts. Because of this, tube amps tend to be heavier and more fragile. Solid-state amps on the other hand have less parts to worry about, and are normally more sturdy and reliable. They are also usually paired with either digital or analog based amp modeling, which allows for a wider selection of tones, albeit without the x-factor that tube adds to amps. Because of this, there are some manufacturers who combine both tube and solidstate circuitry in one amp, but at the end of the day, these hybrid amps will require the same handling care and maintenance as a regular tube amp.
I didn’t want to spend much money (I’m a cheap bastard…part of me thinks I could never truly love a 59 Bassman unless I scored it at a yard sale for a hundred bucks. Now, tone matters more than money to me, but I tend to love the tone of crappy amps just as much as high enders, so I’d feel like a stooge dropping that kind of money on an amp. Especially since I play them and would ruin the collectable value of anything by gigging with it).
Now we switch gears to a company called Unicord, which was owned by Sid Hack. At some point in the early ’60s (probably in around ’64), Unicord purchased the Amplifier Corporation of America (ACA) which was located in Westbury, New York, a northern suburb of New York City. ACA made Haynes guitar amplifiers and an early distortion device powered by batteries.
Vox entered the "lunchbox" amp market in 2009 when it introduced the Night Train (NT15H) head. This compact, all valve amp is a 15W head with two 12AX7 preamp tubes, a pair of push-pull EL-84 valves in its power section, and a solid state rectifier. It uses a cathodyne splitter, and its power section is cathode biased. The amp is solidly constructed on a black steel chassis with a bright mirror chrome finish, diamond-perforated steel tube cage, giving it a physical appearance reminiscent of a lunchbox (some comparisons to a toaster have been made as well). The NT15H also set the cosmetic and operational template for two additional releases, also all valve heads, that book-ended its output power: the 2W Lil Night Train (NT2H) in 2010, which uses two 12AX7 preamp tubes and a 12AU7 dual triode as its power section, and the 50W Night Train 50 (NT50H) in 2011, a two channel head with four 12AX7 preamp tubes and a pair of EL-34 valves in its power section. All models feature the ability to choose between the familiar "chimey" Vox voice and a high gain voice that bypasses the EQ section, via the Bright/Thick switch. Note though that each Night Train model's feature set also provides some unique capability apart from its siblings. For example, the NT15H output power can be switched between 15W pentode and 7.5W triode modes. The NT2H provides a headphone/line out jack with on-board speaker emulation (for practice or direct recording use). Lastly, the NT50H offers two channels by adding a second,optionally foot-switchable, higher gain "Girth" channel, a "Tone Cut" control and a "Tight" switch in its master section, plus a bypassable, JFET-driven effects loop. All models were designed for use with most any 8 ohm or 16 ohm cabinet, although Vox also offers a matching cabinet (NT15H/V112NT, NT2H/V110NT, NT50H/V212NT) for each model.
Cool! Yes, this idea is definitely stolen from G&L!It would be cool to see a picture or schematic, but it’s probably going to be really close to this, if not identical. Meanwhile: Don’t be scared to open up your guitar — they’re build for it! Just be gentle till you learn what you’re doing. I always stand by the Maker’s Faire credo: If you don’t open it, you don’t own it. 🙂
Guitar chords are dramatically simplified by the class of alternative tunings called regular tunings. In each regular tuning, the musical intervals are the same for each pair of consecutive strings. Regular tunings include major-thirds (M3), all-fourths, augmented-fourths, and all-fifths tunings. For each regular tuning, chord patterns may be diagonally shifted down the fretboard, a property that simplifies beginners' learning of chords and that simplifies advanced players' improvisation. The diagonal shifting of a C major chord in M3 tuning appears in a diagram.
.From its G logo cattle brand on top, to the fence rail pickguard graphic, the Chet Atkins Gretsch cowboy'd up big time with cactus, cattle, rifle and arrow inlays inscribed right into the mother of pearl. This 6120W Reissue combines many of the most desirable features of this longtime favorite. Twin Filter-Tron pickups offer lively, hum-free performance, with master volume and tone controls for ease of operation. See pics,pricing and info here
The only guitars that I have been able to find pictures of that have the little curly thingie on the headstocks have been Kents, Kawais and some kind of no-name guitar that looks like the factory took a red Kent 820 and sprayed black around the edges to create a “redburst” finish. The example above appears to has started as a regular sunburst finish with more red and black added. The neck, headstock, pickups, and body are identical to the Kent 820 except the name ‘Kent’ doesn’t appear on the guitar anywhere. Note that the hardware on it is the same as on the 820 shown. That bridge and tailpiece configuration is a little unusual for Kent 820s. (the 820 there is mine) The bridge and tailpiece on the Kent 823 is the more common configuration.
One of the earliest tremolo devices goes back several hundred years and can be found on 16th century Italian and German pipe organs. Like modern day samplers, these early organs had several auxiliary stops including drums, birdcalls, drones, bells, and a tremulant — a mechanism that opens and closes a diaphragm to vary the air pressure of the pipes. As the pressure varied, so did the amplitude, allowing for both vibrato and tremolo.
It helps if you shop frequently but at my Guitar Center the tech is frequently going through guitars on the wall and setting them up so it's ready to be sold without the need for a setup. They have motivation to keep their guitars setup. I mean, have you ever went to a shop, picked up a guitar you wanted, and it had stupid high action? You're not gonna buy it until it's setup right? If they're setup, they'll play better and it'll be a lot easier to sell.
Melodyne is a software application for OS X or Windows with which you can edit audio in a more musical way than was ever thought possible. In Melodyne, you work with notes – and not with a meaningless wave form. You don’t just see where the music gets louder or quieter but also where notes begin and end and at what pitch they lie. You can modify each note and thereby influence direc...
The Ibanez JEM77WDP Steve Vai Signature guitar features a rosewood top on a mahogany body. The maple and walnut neck with a slim Wizard neck profile is topped with a 24-fret rosewood fingerboard with jumbo frets and Tree of Life vine inlays. This model also has a striking wooden pickguard and matching headstock, as well as wooden control knobs, earning it the nickname “Woody.”
Even if your favourite musician is predominantly driven by music and is committed to releasing material for their fans, they cannot possibly deny that are a number of incentives for them to do so. A journalist writing for The Economist online explains that songs are ‘complex mixtures of features’, so composers are always trying to find the right mix of ingredients to increase their chances of success. And everyone loves a success story!
From a perfectionist/engineering standpoint, there is a lot wrong with this circuit. The controls are complexly interactive. There is no really flat setting, as there is a residual midrange scoop unless the Treble and Bass controls are fully down. The action of the Bass control is very uneven for normal taper controls. While the Mid control appears to affect only the mids, it is actually a form of volume control that affects all frequencies, but is the only control that also affects mids. Although it has several imperfections, this tone stack actually helps some of the quirks of guitar, so it works well.
The Epiphone LP Special II Les Paul Collection Electric Guitar is a GREAT GUITAR for $169.00 (The average selling price at the time of this review). The pickups, tune-o-matic bridge and stop piece are the same ones used in Epiphone's more expensive guitars, and are similar to what's used in much more expensive Gibsons. Although the tone adjustments have been simplified to a toggle between the three pickup combinations and an overall tone control for both pickups, this is not as big a deal as many might make of it. Given the vast array of other things that influence electric guitar sound -- strings, amp choice and settings, effects pedals and so forth -- the guitar sounds great as is.
For quite some times now, many musicians have been making use of the distinctive sound and look of Koa wood construction on instruments. Designed to meet the taste of Hawaiian culture and tradition, the Koa wood on the ESP LTD EC-1000 is native to Hawaiian island, boasting a remarkable history and well-deserve popularity for its recognizable natural reddish and grain pattern eliciting a well-balanced sound while adding tone brightness without affecting the guitar’s warmth.
So there you have it. An absolute workhorse with fantastic sounds, and just about a must-have pedal no matter what type of guitarist you are and no matter your skill level. Equally a perfect first pedal to buy as it is a perfect last pedal in your collection. The biggest downside is that it probably can’t be your only pedal, since you can only use one effect at the same time. Famous users include Russel Lissack of Bloc Party, James Edward Bagshaw of Temples, and Dave Knudson of Minus the Bear. At the “too good to be true” price that it sells for (seriously, we’re not just saying that, one of our writers immediately sold his DL4 and bought the M5), this is without a doubt the Best Bang for your Buck.
Continuing to look at the well-known Fender brand, the Stratocaster American Standard is a higher-priced option with necessary features for the seasoned guitarist. This is another one of the most popular electric guitars ever. In terms of build, the body is a mix of ash and alder, creating a balanced tone for both the sharpness of the upper range chords and the dense resonance of the lower range progressions. The modern bridge has an upgrade of utilizing a block infused with copper and steel saddles for strong intonation and an ease in adjusting pitch. The tuners are placed at varying degrees and heights, with this staggered design creating a decreased in reverberation and excess hum so as to focus in on the clarity of the sound. This electric guitar also has a custom designed single-coil strat known as the “Fat ‘50s”, which is intended to create a fuller sound compared to other guitars. With a comfortable ‘C’ shaped design and durable finish, this 22 fret guitar offers desirable features for the guitar enthusiast. If you’re unsure whether to grab this or our previous Fender pick, read this Telecaster vs. Stratocaster sound article for some more info.
: : Does anyone know for sure where these originated. I have been told Vox (the England years) made this flat bodied plank guitar in the skiffle days of early 60's/late 50's. Mine is painted white(by hand) with a large black pick guard that curves to envelope the two chrome "toaster" pickups ,bottom of neck, and three control knobs.The strings have a moveable maple bridge(not secured) and a small chrome hardtail heel.The neck has a zero fret at top and 19 more playing frets.There are dot inlays at the 3rd,5th,seventh,ninth,12th,and 17th frets.The headstock is of natural finish light maple with a top edge cut at a sloping angle like Hofner.It has brass tuning pegs,gears and gear plates and the keys are white plastic.The beautiful short neck is true ,natural maple.Along one of the tuning gear plates is the numbers: 35515 which are etched into the wood. Four bolts without any plate hold the neck base to the plain body and a green decal above the pegs at top face of headstock reads: Shadow. The fret board is rosewoodand is laid on neck without bindings.It has six strings and sounds like a short scale Baritone guitar. It also only has one strap peg at bottom since they used to put the other end of strap on a tuning key. No other holes are seen for any former peg at other end of body(where normally found). Please send any info on this small,early,simple but awesome sounding electric skiffle guitar from England(Vox?).Thanks!!!!!
The company has been run by the Martin family throughout its history. The current chairman and CEO, C.F. ‘Chris’ Martin IV, is the great-great-great-grandson of the founder. The firm was the first to introduce many of the characteristic features of the modern flattop, steel-strung acoustic guitar. Influential innovations include the Dreadnought body style and scalloped bracing. Some time in the 1970s, Martin bought Levin guitars and around 200 D-18’s were apparently built in Sweden; they are stamped LD-18.
Fuzz pedals provide guitarists, bass players and even keyboard players with a hefty amount of distortion that sounds VERY different to regular distortion sounds. Fuzz pedals make your guitar sound like its pushing your amplifier to the point of blowing up. A fuzz pedal completely changes the sound of your guitar signal into a heavy, fizzy, and extremely noisy sound that, depending on which pedal you choose, can provide a bass heavy noise, to a spitting ‘broken’ amp sound. Think Velcro being ripped apart and you’re somewhere pretty close.
It can get a bit difficult trying to properly depict certain aspects of effects pedals to our newer musicians out there since much of music tends to be described in an intangible sort of manner which relies heavily the assumption of prior knowledge and personal tastes which is why we try our best to not get the pros out there the meat of the information they are looking for, but describe it in a way that players of even entry levels can comprehend. So with that in mind, one of the more complex aspects of effects pedals for newer musicians is their implementation of a signal chain.
Guild acoustic guitars are played by some of the best professional musicians in the business. From this standpoint, Guild is on par with Martin and Taylor, and completes the triumvirate of American acoustic guitar titans. As you’d expect, the prices follow suit. However, the GAD series offers a way for intermediate players to get a Guild acoustic for a reasonable price.
Some bass amplifiers have an "overdrive" or distortion effect built into the unit. The Peavey Century 200 has an onboard "distortion" effect on the second channel. The Peavey VB-2 also has built-in overdrive. Aguilar Amplification's AG 500 bass head is a two-channel amplifier, one of which offers a "saturation" control for overdrive. A variety of BOSS combo amplifiers have a built-in "drive" effect. Gallien-Krueger's bass amp heads have a "boost" control which provides a simulated tube overdrive effect. The Behringer Ultrabass BVT5500H Bass Amplifier Head has a built-in limiter and overdrive. The LowDown LD 150 bass amp has a range of overdrive sounds, from a slight hint to heavy distortion. The CUBE-20XL BASS amp includes built-in overdrive.
What style of music do you play? While there are many versatile guitar amps that can be used for many styles of music, if you play a particular style of music a majority of the time, then you should get an amplifier that best suits it. Do you play acoustic or electric? Certain guitar amplifiers are designed specifically for acoustic guitars although it is possible to play an acoustic through any amp. In terms of styles, jazz players typically do not need an overdrive option as clean tones are best suited for that style of music. Blues aficionados will be happiest with a clean channel plus an overdrive channel with plenty of sustain, such as one finds on many vintage Fender models. Shredders will require an amp that will accept distortion pedals without losing signal quality. Do your research regarding which guitar amps are best suited for the type of music you play.
The fact is, the qualities of different strings can have an effect on your guitar’s resonance and tone, on the quality and responsiveness of your attack as a plectrist or finger picker, and impact your speed and other important factors. And think about your budget. Some coated strings list at nearly $20, while a good basic set of electric guitar strings can be scored for $3 to $4 on sale.
Ibanez Mikro GIO Electric Guitar in Black w/ Bag. The guitar is in good working condition does have few marks and one nick. Does not include stand just used to take pictures. Includes guitar strap and Ibanez bag. Please contact me if you have any problems with your purchased item and I would be Happy work with you to help make your Transaction a Pleasant Experience. Please check photos carefully and use the enlarging tool. Some photos are taken with a flash and may cause the image to appear darker in some areas. Photos are an important part of the description and the condition of each item.Thanks for Looking!! Also please verify the correct shipping address before bidding. Payment is expected within 48 hours.
Their designs do not require them to have comparator inputs as with solid-state amps. The small amount of negative feedback in valve amps is only required to provide damping to the speaker. Valve Amplifier Design From physics we know certain things must be a particular order and size to be efficient and this is acutely so with valve amps. 60Watts is the minimum power capacity for an amplifier to bring quality speakers to life with full fidelity.
Technically, distortion is defined as being any change to the original signal other than in level. However, we tend not to think of processes such as EQ and compression as distortion, and the term is more commonly used to describe processes that change the waveform in some radical and often level-dependent way. These include guitar overdrive, fuzz, and simply overdriving analogue circuitry or tape to achieve 'warmth'. In the analogue domain, heavy overdrive distortion is usually created by adding a lot of gain to the signal to provoke deliberate overloading in a specific part of the circuit. Such high levels of gain invariably bring up the level of hum and background noise, so it may be helpful to gate the source. Though overdriving analogue circuitry is the traditional way of creating intentional distortion, we now have many digital simulations, as well as some new and entirely digital sound-mangling algorithms.
Wah pedals make exactly the noise they’re named after – yep a “Wah” noise! If you say to yourself “Wah, Wah, Wah” slowly, that’s the same sound the pedal makes. Imagine a baby crying in slow motion and you kind of get the idea. The Wah sound was probably best captured on “Foxy Lady” by Jimi Hendrix and is widely used in funk and rock solos thanks to its really cool sounding effect.
Our fretwork is one of the things we are most proud of. We go to the extreme to make sure that your guitar is going to play the best it can. The fingerboard is planed under tension. The fretting process is done with epoxy fretting. We use a special blend of epoxy that makes re-fretting very easy without messing up your fingerboard. This process is used for multiple reasons. One of the advantages to this type of fretting is that you lose the hollow gaps under the fret that you find with the traditional way of fretting. In traditional fretting, with each fret you put on, it is like driving a wedge into the fingerboard, which causes back tension on the neck. With epoxy fretting, all of these issues are eliminated. The epoxy under the frets helps to transfer string vibration throughout the neck to the body, and relieves all stress and tension on the neck that occurs with traditional fretting. This results in a stress-free neck, which allows the truss rod to work properly and to adjust the neck accurately.
The $300-$500 price range of acoustic guitars is perfect for all levels of players. Whether you are a beginner, intermediate or advanced player, this price point gets you a good guitar that will sound great while not breaking the bank. While you won’t find any American made acoustics under $500, you will find some by popular American brands offering cheaper versions of their high end guitars that are made in Mexico or China.
A comparable alternative at a fraction of the price to the Axe-Fx (which also made the list), the Line 6 Pod HD Pro offers a ton of amp models and effects within it’s 2U rack interface. With over 100+ premium effects, 16 different cabinet models, and even eight microphone models, the Pod HD Pro gives you complete control over every aspect of your tone. All of this is complimented by an intricate display that lets you know exactly what your virtual signal path is. Add the ability to use a mic, bass, or your Line 6 Variax guitar for recording or live scenarios, and you’ve got the best of every realm of music-making at your fingertips. Oh, and to answer the most important question: Does it djent? Yes.
• Stop: A stop tailpiece is a bar, typically made of an alloy, which is held to the body of a guitar by large screws threaded into embedded sleeves. They are most often aluminum, zinc or brass based, with the latter the most costly. Aluminum has a few advantages. When the stop tailpiece was perfected by Gibson over a half-century ago, the originals were made of aluminum. Many players prefer those today for the vintage vibe, but aluminum is also the lightest weight tailpiece alloy, which some believe allows the strings and the guitar’s body to connect — which is another function of the tailpiece — in a more resonant fashion. It’s best to be careful while changing strings with a stop tailpiece, because they sometimes fall out of their sleeves and can scratch the finish.
The EM-18 came with either a pair of Mighty Mite humbuckers or a pair of DiMarzios. It was otherwise the same as the E-18 with the addition of a three-way mini-toggle coil selector switch which allowed a choice of both or either coil on the lead pickup. This arrangement allowed for a rather remarkable variety of tones, by the way. EM-18 production began in 1979 and some 1,375 were made until the guitar ended in February 1982.
Although Orbison’s good friend and Sun Records labelmate Johnny Cash may be known as “the Man in Black,” Orbison habitually dressed from head to toe in black in the early Sixties, a decade before Cash adopted his dark uniform. Even Orbison’s raven hair and impenetrable jet Ray-Bans were blacker than the cover to Spinal Tap’s Smell the Glove, adding to his alluring persona as a mysterious, brooding artiste.
Electric guitars are solid-bodied guitars that are designed to be plugged into an amplifier. The electric guitar when amplified produces a sound that is metallic with a lengthy decay. The shape of an electric guitar is not determined by the need for a deep resonating body and this had led to the development of contoured and thin bodied electric guitars. The two most popular designs are the Fender Stratocaster and the Gibson Les Paul.
Schecter Guitar Research is a company that has really established themselves as one of the best guitar brands out there in recent years. Many of their guitars are focused on the heavy metal market, but players of any genre can find a Schecter that meets their needs. With superb craftsmanship and high-end appointments you’d expect to find on much more expensive guitars, they are also among the best values in the guitar world.
You’re probably not going to damage your laptop by plugging in a guitar. But take it easy. Instrument output is usually about 10dB louder than mic level and 10dB quieter than line level. But there’s a big variation between instruments, and of course, your guitar has a volume output. On an electric, it’s just an attenuator — there’s no active circuitry, the volume knob just knocks down the output of your pickups, some use it as creative control, some just to match a cheap amp better.
Launch price: $779 / £849 | Body: Mahogany with maple top | Neck: Maple | Scale: 25" | Fingerboard: Rosewood | Frets: 24 | Pickups: 2x 85/15 'S' humbuckers | Controls: Volume, tone (with push-pull coil-split), 3-way selector | Hardware: PRS vibrato, PRS SE tuners | Left-handed: Yes | Finish: Fire Red Burst, Tobacco Sunburst, Trampas Green, Whale Blue
When you hit a string it will vibrate. It will continue to vibrate until the energy put into it is expended. Where does that energy go? Well, it is expended through movement. That movement is what the pickup "sees" and translates into sound. In a world where 100 % of the initial energy imparted by the strum to the string was expended through movement, wood doesn't matter.
I have an acoustic Decca and a brand new Fender acoustic. Not only is the Decca easier for me to play because I have tiny little doll hands, I think it would hold tune if I threw it out of a moving car. I put both the Fender and the Decca into storage for two years - I just got them out recently. The Fender popped the B string and took a good twenty minutes to tune. The Decca was *STILL* *IN* *TUNE*. Plans have changed; I am selling the Fender and keeping the Decca!
In 2008, Gibson USA released the Slash Signature Les Paul Standard, an authentic replica of one of two Les Pauls Slash received from Gibson in 1988. It has an Antique Vintage Sunburst finish over a solid mahogany body with a maple top. Production was limited to 1600. The Gibson Custom Shop introduced the Slash “Inspired By” Les Paul Standard. This guitar is a replica of the 1988 Les Paul Standard and it features a carved three-piece maple top, one-piece mahogany back, and rosewood fingerboard, with a Heritage Cherry Sunburst finish. Two versions were made available—the “Aged by Tom Murphy,” aged to resemble the original guitar (a limited number of these were signed by Slash in gold marker on the back of the headstock), and the “Vintage Original Spec,” created to resemble the guitar as it was when Slash first received it.
Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Custom - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Diecast, Gold, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Ivory, Sunburst
The following chart will help you choose the right sized guitar for your child. It is important to note that guitar size is only one part of making it easy for your child to play. An un-adjusted guitar will not be easy to play, even if it is the right size. Here at FirstGuitar.com, each guitar is inspected, properly adjusted and set up so that the strings are easy to press down and the notes ring clearly.
Flanger pedals are based on a studio sound made when two tapes were mixed together and one was delayed. What this does is add shifting harmonic content to your signal, as well as modulation. Flanging is a very distinct effect that adds a unique whoosh or airplane-like sound. Used with restraint, the flanger adds an interesting dimension to your sound, almost synthesizer-like sound. Used at extreme settings, flangers will over take the tone and bring a solo to completely different sonic level.
If a bold vintage look and a big vintage sound gets you excited, the beautiful Art Deco-inspired BG-2500 from Blueridge will be right up your street. Taking inspiration from the historic Gibson J200, this high-end model sports a jumbo 21” body made from quality woods, with a fit and finish that ensures the BG-2500 feels worth the hefty sum of cash.
Ken Rosser picked the Spider Classic 15 as his favorite of the amps we tested, saying, “I think the effects on the Line 6 sounded the best. It gives you a nice range of tone options. The clean tones stay clean even at loud volume, which a lot of these can’t do. One caveat is that, when you switch the amp sound, it changes the way all the knobs work, so the sounds can really jump out at you.” Fred Sokolow liked the Line 6 in general, saying, “I could pretty much figure out what to do with it, but I could figure out the Fender more easily.”
Double-coil or "humbucker" pickups were invented as a way to reduce or counter the unwanted ambient hum sounds (known as 60-cycle hum). Humbuckers have two coils of opposite magnetic and electric polarity to produce a differential signal. Electromagnetic noise that hits both coils equally tries to drive the pickup signal toward positive on one coil and toward negative on the other, which cancels out the noise. The two coils are wired in phase, so their signal adds together. This high combined inductance of the two coils leads to the richer, "fatter" tone associated with humbucking pickups.