Some versions of the TG-64 had the same floating-table vibrato system as on the SD-4L; my guess would be that these were earlier versions, although one can’t place too much faith in dating Japanese guitars by hardware appointments. Others had the more typical Japanese version of the Bigsby vibrato. This guitar was sold in the United States in ’65 as the Teisco Del Rey Model ET-320, but by ’66 had been dropped from the line.
Once you start getting into reverb, it won’t be long before you start noticing different nuances of this effect. A good portion of digital reverbs sound too sterile, while some analog can be too narrow in range. Finding that perfect type of reverberation matters if you are serious about building your guitar tone properly. Built in reverbs you usually see in lower quality amps are good for home practice and not much more. That isn’t to say that the added value of them being available in the first place is a bad thing. No, but you can’t really rely on those reverbs to get you anywhere serious. On top of that, a good analog reverb pedal is a one time purchase.
Lawsuit Takamine F375s Hand built in Japan and still in excellent vintage condition! Build type is Rare Exotic Tone woods series Jacaranda Brazilian Rosewood back-sides-fingerboard & headstock overlay JUST Gorgeous. Its workmanship is really top shelf by any standards, We installed and set up with Martin Marquis 80/20 strings 12's, as well as setting this guitar up with a New bone nut & saddle, Condition is very good with a few minor hard to see scratches on its back you have to look closely sometimes at an angel ( clear coat only not threw to wood ) general play here and there as any 37 year old guitar that has been played would get... dinks and such but nothing major to detract from its obvious outward beauty, This example has an excellent neck its 1-11/16th's at the bone nut, fingerboard is very good as are the frets at 90%, its straight and has a nice meaty feel, has the Martin design detail of the Diamond Volute on back, original tuners are excellent as well, a warm vintage vibe to this 37 year old vintage Gem. Tone is rich with good volume she Sings well!!! JVG Rated 9/10 higher if it wasn't for the few minor clear coat scratches in its clear coat not to the wood that I can see more like swirls and such may be possible to fine grade 3000 wet sand and polish out its possible if it doesn't sell soon when I get the chance I'll do it, its a commitment because it may not sand out alone it may require a few thin clear lacquer applied and buffed out to cure it forever if so a guitar of this caliber deserves the attention.. ( the price will go up after I do that work ) and that really doesn't have to be done to make this guitar just very good -excellent vintage it would bring it very close to mint!.... aside from the few minor scuffs this guitar still qualifies as vintage excellent right now, just thought I would point those out. So to be clear about this listing the way you see it now is the way it is offered.Its a F375s and not the EF375s yet This guitar has a factory installed transducer type pickup installed and it sounds wonderful, Its said to have been installed by original owner in Tokyo by Takamine shop its a very clean job I call it CLEAN where they do not make extra unnecessary holes for output jack instead they use the END PIN hole and its a combination strap pin and or output jack, So this guitar is either Acoustic or Electric really nice in deed in SUPER Condition well above average. This beautiful instrument comes with its original hard shell case it to is in very good vintage condition its heavy duty molded type with plush black interior all functional fully. This is the total package. Contact Joe to buy: .
FU was non-stop work & fun at the 2014 NAMM Show in Anaheim California! It was great to be back in the southern California sun with 85 degrees while freezing snow and blizzards were happening back east! The fun started with an opening night party with Eddie Van Halen and the launch of several new EVH Guitar models. The rest is just a blur but here are some out-takes to enjoy, For more behind the scenes photos check out our Facebook page!
The original Les Paul featured a solid mahogany body capped with a maple top, which produced an instrument capable of many tonal variants with maximum sustain.  Although the first Les Pauls included two P-90 pickups, they are most well known for their two PAF humbucking pickups.  While many variants are produced, the double humbuckers put the Les Paul in a league of its own, separate from the offerings of Fender’s Telecaster and Stratocaster.
Hybrid amps are a strange beast. As the name suggests, they combine multiple technologies to produce a unique hybrid amp experience. They may use the digital front end of a modeling amp with a tube-based power stage, or a tube preamp with a solid-state power amp. The benefits of this style of lesser-seen amp is that you can sometimes get the best of both worlds, with the awesome tone of a tube amp, but with the processing power of a solid-state amp. These amps tend to be cheaper than tube amps and generally easier to maintain.
In addition to the alignment problem, there are other problems with using a simple text editor. For example, you'll have to align all the notes of a chord yourself... it's not easy to insert a new passage... if you make a mistake you can't just move the note... and to your system, it's just another text file. If you want to programmatic help to simplify your work, or if you want extra power (such as song playback, chord charts, and scale generation): use a TAB program.
Also worth an honourable mention is the iconic Gibson Hummingbird, a square-shoulder dreadnought named after the bird which Gibson best felt described its unique qualities. The Hummingbird is one of those unique things in that it’s an acoustic guitar which eschewed the industry-standard natural wood finish of around 98% of its peers in favour of a cheery sunburst finish more commonly seen on Gibson’s now famous electric guitars like the Les Paul and ES-335.
This tuning may also be used with a capo at the third fret to match the common lute pitch: G-c-f-a-d'-g'. This tuning also matches standard vihuela tuning and is often employed in classical guitar transcriptions of music written for those instruments, such as, for instance, "La Canción Del Emperador" and "Diferencias Sobre Guardame Las Vacas" by Renaissance composer Luis de Narváez.
The Effect:Reverb pedals have remained a staple pick in each guitarist’s arsenal in order to provide that extra sound refinement and enhancement when necessary. It may be tricky, learning to apply the right amount of Reverb, as too little may go unnoticed, and too much may sound silly, yet finding that sweet spot is definitely thrilling and satisfying. Great option for every beginner (or a so called must have guitar pedal) is the Boss FRV-1 63 Fender Reverb Pedal. If you want to dig deeper into the reverb effects, check out our dedicated article, the plethora of reverb pedals for you to choose from will surprise you.
Like all Vintage electrics, it comes as standard with Trev Wilkinson designed hardware and pickup. The VS50IIK Vibrato system can take some serious abuse and yet still return to pitch time after time, thanks to the added inclusion of Wilkinson WJ07LH E-Z-Lok machine heads. Meanwhile, the Wilkinson WHHB double-coil pickups provide tight bottom end and crisp highs, perfect for a variety of genres.
It’s provided as-is with no support, but it’s still well worth checking out if you’re on a PC. According to the developers, it was born inside an academic research project about the modelling of electric devices, and then applied to the musical instrument field as an evolution of the techniques available in commercial units. Its most important feature is the high precision of the simulation.
Because of stiff competition in today's low-end market, guitar companies are constantly trying to outclass each other by improving the quality and value for money of their instruments. One brand that consistently tops in terms of sales and feedback is Epiphone, a sub-brand of Gibson that specializes in quality mass produced guitars. The DR-100 is a great example of their impressive ability to balance quality and affordability, garnering nearly perfect positive feedback for its build quality and sound.
Best acoustic I've owned. It's an Oregon dreadnought, an all round stunning looking guitar. The sound is beautifully balanced, clear with nice defined bass, sits perfectly in the midrange and projects well without being too bright. It's light weight with meticulous craftsmanship and beautiful timber. When you look at these guitar it's obvious that they are built with a lot of care and attention to detail.

In 1964 Hohner released The Beatles Harmonica Kit which was sold in a blister package, much like most Hohner harmonicas nowadays, retailed for $2.95, and help what Hohner calls "bring about a new popularity upsurge of the Hohner harmonica on both sides of the Atlantic.".[6] In the 1970s Hohner began manufacturing acoustic guitars,[7] and re-producing electric guitars.[5]
If you really like to cover all options, record using any of the above methods but also take a straight DI feed with no effects and record that onto a separate track so that you can process it later. Some engineers have been known to use a recorded DI guitar track to drive a guitar amplifier, which is then miked up and re-recorded, but you could take the easier route of using a hardware recording preamp or a guitar amp emulator plug-in to process the track.

Portable- you can carry them in one hand to jam with friends, take to your guitar lesson, or even play at a small party. The Fender “Frontman” 10 watt weighs only 8.5 pounds and brand new costs only $59. Another fun amp is the Danelectro “Honeytone” that only costs $19.99 and is equipped with a belt clip so you can walk or roller skate around while playing your guitar.
How about comparing the guitars only by the sound alone. Especially when overdriven playing in the realms rock and plug on the same amplifier or using the same set-up. Arguably there are many guitarist would find less expensive guitars are not bad at all. That they are also very much capable of producing the needed dirty tones and also able to produce a decent smooth clean sound to let players go out there and play.

by pedalhaven Black & white board from  @alexjacob_ ! Here’s the signal chain: Boss TU-3 Chromatic Tuner EarthQuaker Devices Palisades Boss NS-2 Noise Suppressor Hotone Nano Legacy BritWind (Effects Loop) Boss NS-2 Noise Suppressor Joyo D-SEED Digital Delay TC Electronic Arena Reverb Don't forget to DM/Tag us to submit your photos! ▪️ ▪️ ▪️ ▪️ ▪️  #pedalhaven   #pedalboard   #guitarpedals   #knowyourtone   #ambienttones   #pedalboards   #pedalnerds   #pedalporn   #guitar   #gearporn   #gearnerds   #pedalboardpeople   #shoegaze   #geartalk   #guitarsdaily   #gottone   #tonefordays   #guitargear   #reverb   #gearpost   #boardshot 
Tremolo bars - Many lower-end guitars are designed to look cool and are equipped with floating bridges for super tremolo bends and flutter. They look cool , but a sad fact is many of these lower end models have low quality hardware. There is nothing more frustrating than being a newbie, buying a hot looking guitar, and have to fine-tune it every 2 minutes. Avoid this, or buy a decent bridge for around $100.00 extra and install it.
The Ultimate Beginners Series gets aspiring musicians started immediately with classic rock and blues riffs, chord patterns and more. Now, for the first time ever, Basics, Blues, and Rock are combined in one complete book and DVD set. Follow along with 4 hours of DVD instruction and 3 hours of audio tracks, with the help of on-screen graphics and printed diagrams. The Ultimate Beginners Series: Electric Guitar Complete takes you from picking to soloing and power chords. If you're serious about mastering the blues and rock styles, this book and DVD set is a must-have.
All of the hardware is gold on this model, and while it’s stock Epiphone stuff rather than licensed equipment, it’s of good quality, and we don’t expect it to be difficult to keep in tune. The eSonic preamp and NanoFlex pickup system are both excellent and really help the guitar to come alive. In terms of looks, there are no particularly notable features, but the combo of gold hardware and florentine cutaway make for an attractive design.
But note that guitars in this price range aren’t likely to be without their faults. You will probably need to take them to a local guitar pro for a set-up if buying online, as fret edges may be sharp and the action may be too high or low. Finishes can be a little rough in some places, and you won’t get anything in the way of luxury looks or features – there’s a lot more plastic used in the under $150 range!

The Salamander Grand made by Alexander Holm (details above) who sampled his Yamaha C5 Grand and is quite well known for having a great sound. Most sf2/sfz versions seem to be lacking the proper dynamics, have latency problems or have been oversimplified. This sf2 version has addressed these issues yet retains its essential character including optional resonance but removes other non-essential sounds such as pedal noises.

The objects connected to the red and purple wires are a capacitor and resistor in series. The round brown object is a capacitor, typically around .001 microfarads. The rectangular brown object is a resistor, typically around 150K ohms. Increasing the value of the capacitor will expand the treble range you're preserving. Too large a value, end you'll be preserving midrange, too. Too small a value and you'll only be preserving the highest treble frequencies.
Alvarez has always been an under-rated brand. Beautiful workmanship, great sound- an excellent value for the money. I have one of the old six string "dove" guitars and a Yairi 12 string: both are close to forty years old and both still sound and look great and have never needed any repairs. I also have an old Martin six string. I have done the "blindfold" test with friends to choose the best sound between the alvarez and the martin - alvarez wins every time.
Vibrato: Vibrato effects produce slight, rapid variations in pitch, mimicking the fractional semitone variations produced naturally by opera singers and violinists when they are prolonging a single note. Vibrato effects often allow the performer to control the rate of the variation as well as the difference in pitch (e.g. "depth"). A vibrato with an extreme "depth" setting (e.g., half a semitone or more) will produce a dramatic, ululating sound. In transistorized effects, vibrato is produced by mixing an instrument's audio signal with a carrier wave in such a way that generates frequency variations in the sound wave.[81] Guitarists often use the terms "vibrato" and "tremolo" misleadingly. A so-called "vibrato unit" in a guitar amplifier actually produces tremolo, while a "tremolo arm" or "whammy bar" on a guitar produces vibrato.[83][84]
The neck is also crafted from mahogany, topped by a 20-fret rosewood fingerboard with a standard scale length of 25.5" and a nut width of 1.75". In contrast to its vintage looks, the neck follows a slim "C" profile that is as easy on the hands as it is on the ears. Finally, this guitar is wrapped in a nice gloss cherry red finish that stands out easily on any stage. Check this one out if you're looking for a quality mahogany body acoustic guitar with an old school vibe.
You can divide these further into cabinets and combos. A cabinet is simply an amplifier without a head. The head is all the knobs and so on that can be tweaked to produce variations in tone and volume. Combos include the head, so they're often preferred as they're easier to port around. However, if you want a multi-speaker setup, you'll want to opt for cabinets with separate heads.
ACTION: fret low E at first fret and measure the distance from the bottom of the to the top of the 15th fret. It should be 5/64". Do the same with the high E, measurement should be 3/64". Now measure the string height at the nut; underside of the string to the top of the fret. Low E and A should measure 2/64", D and G =1.5/64" and B and high E = 1/64". If string height at nut is correct, recheck string height at 12th fret with strings open. Measurement for low and high E's should be the same as measurement taken at the 15th.

New from Stewart-MacDonald are guitar wiring kits with the premium brand pots, switches, jacks, capacitors and cloth wiring used in original Gibson Les Paul and SG guitars. The kits make it easy to order top-quality components for wiring or re-wiring a 4-control / 2-pickup guitar with a 3-way switch. The kit components include Switchcraft toggle […]
These samples are released under the GNU GPL license. The source code being the sf2 files (of which contain the audio samples and settings). The samples and settings can be accessed within Viena and Translator Free on windows or Swami on linux. This license means that you can do what you like with them but if you create any samples from them or improve on them then you have to use the same license in your projects. This way it keeps it open source (and therefore free). This license is only concerned with the source code. Any music you create with them is nothing to do with me (i.e. you take all the royalties and use whatever license you like).
It’s best to perform pickup adjustments while playing through a clean amp. You can more accurately hear the true tone and volume of each pickup when the signal isn’t being compressed or overdriven by a cranked amp or pedal. Listen to the tone of each pickup position, and try to balance the height of each pickup until the volume remains relatively the same when changing pickup settings.

SOLD OUT! Takamine EF406 RARE Here we have a RARE and GORGEOUS 1999 limited Edition Takamine acoustic-electric guitar, model EF-406. This instrument is a PREMIUM example of a New York or also called a Parlor guitar and is a Hand Crafted in Japan model an amazing example of Japans high Quality workmanship & fit & finish and is truly just as good as it gets. As you can see from the pictures, it is simply gorgeous to look at. It has a classic slotted headstock with Top Quality gold open gears and gold tuners with Pearl buttons. The Top- Back & sides are all a High grade choice AAAA FLAMED KOA with natural Koa color (there is no stain)and none was needed to bring out the AWESOME grain patterns of this Rare Native Hawaiian Wood. The top sound hole apears to be bound or painted and inside looks same as out /all Takamine internet information leeds to say the tops on this model is solid however we can not guarantee this as fact. The electronics are a GRAPH-EX pre-amp system: peizo transducer, with "exciter," volume, bass, treble, and mid controls. It comes with a deluxe, plush hardh shell case, note: In he picture close up of the ack of the headstock you may notice a dull spot running threw the center over the made in Japan tag area this is just a spot of waxed area that was inadvertently missed and not rubbed out... it is fine this guitar is in Excellent used condition. .
John and I weeded out a couple of guitars that arrived in far-from-playable condition because we think every guitar should be at least reasonably playable when you buy it. Avi Shabat agreed, saying, “The more messed up a guitar is when I get it, the more I have to charge for setup.” We also didn’t have the short-scale guitars set up, for two reasons: First, we think a guitar for kids—one that’s likely to be purchased at a low price and given as a present—should play acceptably right out of the box with no setup; second, all of the short-scale models we received did play very well out of the box, and all were equipped with strings of the same approximate gauges.

Yamaha is considered as among largest music instruments selling company in India, which provides a wide variety of guitars. S series, Yamaha RGX, RGZ electronic series, SG series (SG 5,SG 7) etc are the best models of guitar. Now they become the world’s largest manufacturer of a full line of musical instruments. They earned good name by providing super quality guitar at an affordable price. Available price is Rs. 8,000/- onwards (approx).
There is one drawback though, rather than signal that they might want a little more gain, too many players simply grab their volume knobs without warning. (the “sandbagging” I referred to previously), or kick in an overdrive pedal they “forgot” to check during SC. What sounds good for them onstage can send the audience running with bloody ears, Techs running for the backup cab cables, and lawyers sharpening their fangs. A little gain in their monitor, becomes multiplied by the power of the FOH. Sometimes it is a thought to let them blow out an amp speaker, rather than a bank of FOH speakers!
So far I am very happy with this guitar. Right out of the box, it was set up perfectly, low action, no fret buzz, and it sounds great. (a sticker on it indicated it was inspected and set up in the usa) I have a feeling that once I swap the strings that came on it for elixirs it will be even better. The built in tuner is very handy, and consistent with the snark I typically use on other guitars. It sounds really good through an amp too, as the dual pickups and blend function create a very versatile range of tones one can achieve quickly. I am really impressed for the price, and I'm 100% sure this will not be my last Epiphone.
Starfield was a guitar brand owned by Hoshino Gakki. In the 1970s, Hoshino Gakki and Kanda Shokai shared some guitar designs and so some Ibanez and Greco guitars have the same features. The Kanda Shokai Greco guitars were sold in Japan and the Hoshino Gakki Ibanez guitars were sold outside of Japan. From 1982, Ibanez guitars have also been sold in Japan as well as being sold outside of Japan [3].
Before recording, make sure that the guitar is in tune, with a fresh set of strings, and that you check the tuning regularly. New strings always produce a brighter sound and better sustain. If the instrument has been properly set up, string and fret buzz should be minimal; while this type of noise is much less obvious when playing through heavily- distorted or overdriven amplifier settings, it can be very distracting when using clean settings or recording directly.

May Music Studio's Guide: The May Music Studio isn't a true "blue book." Rather, it is the website of a guitar studio that provides a quick tip guide to help you determine the fair market value of your guitar. The studio has years of appraisal experience and though they no longer offer appraisal services, their wisdom is distilled in the evaluation tips that they describe on their site.
Description: Body: Maple - Flamed - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Custom - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Diecast, Gold, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Brown

I am writing this due to the mixed reviews that I read before buying this. This is a really powerful device. I have had a POD 2.0 for years. This is just as good and is also small, portable, and inexpensive. Most of the criticism that I read is that it is not well made and durable. It is well made, but I don't think it is designed for gigging. It is perfect for practicing or interfacing with a home studio. If this is your application, then you will be very satisfied. One other thing that I found true of this and similar devices that I own is that the quality of the headphones makes a big difference. If you use studio quality headphones it will sound great, if you use music player headphones it will just sound good. I haven't ... full review
The Squier Bullet Strat Hard Tail Brown Sun Burst is a fantastic option for beginner guitarists out there and those who need an affordable budget friendly option for recording or practising. This guitar makes our cheap electric guitars that don’t suck list thanks to its high-quality basswood body and comfortable “C” shape profile on the neck that is super comfortable to play. This high-quality guitar also includes a set of three standard single-coil strat pickups allowing you to mix up your sound via the 5-way pickup selector. Solid, chrome hardware and a hard tail bridge for added resonance finish off the guitar nicely whilst the budget friendly price tag makes it affordable for everyone. A Fender Stratocaster style guitar at a fraction of the cost.

My 15 year old daughter recently renewed interest in the guitar she had bought a few years ago but had never really played much.  She was disappointed when she noticed the strings were loose.  We brought it here and Ted was so helpful and engaging. He recommended new guitar strings; normally you can buy the strings and do it yourself, or pay them to do it.  He readily understood that while my daughter didn't know how to do it herself, she would like to know. He showed both my girls how to string a guitar, talking them through each step while he expertly strung the guitar and got it in perfect tune. Ted teaches guitar and his tutorial was an excellent recommendation of his teaching skills.  He also threw in a cleaning cloth and gave us chocolates - how much better does it get than that?!

Despite its high production figures, Fernandes is better known in the United States for its Sustainer system, which uses electromagnetism[1] to vibrate a string for an extended period, so long as the user continues to fret a note.[2] Unlike the similar manual E-Bow sustainer, the Fernandes Sustainer can be used with a standard plectrum, because the sustainer is imbedded in the body of guitar. Fernandes' custom shop has installed numerous Sustainers into guitars built by other manufacturers.
You want a guitar that isn't going to fight you - If you're a smaller person, you'll want a guitar with a smaller body. And if you have particularly small hands, it might be worth looking into a 3/4-size guitar to start out. The way the guitar looks is going to matter a fair bit as well. If it doesn't look good, you aren't going to be as inspired to pick it up and practice.
That's right, we have another Martin guitar. This time around it's the Martin DCPA4R from their Performing Artist series. This guitar is not really the very best they have to offer, but we feel that it combines all of what makes Martin so unique at a price that isn't impossible to afford. Because there are some insanely priced ones out there from Martin and others, but funnily they aren't the best of the best, just the most expensive.
I had gotten rid of all my effects pedals a long time ago because I wasn't using them. So when I saw this little processor and the price I thought I would give it a Try. I was amazed at all the sounds and tones this thing puts out. For the little money you spent it is deff. worth it. I have not yet messed around with the drum settings but I will. This will be loads of fun to play around with. A deff. 5 star rating.

Here you get a very bright sound but the output will be less than if it were wired in series and you no longer have hum canceling. Since you are using just one half of the humbucker, "coil-cut" sounds best when using a high output pickup (DiMarzio "X2N", DiMarzio "Distortion", Seymour Duncan "Invader", Seymour Duncan "Distortion", etc). A coil cut switch is relatively easy to wire up and it is just a matter of connecting one end of an SPST switch to that junction that was created for series wiring and connecting the other end of the switch to ground. So, we now have another 2 tone humbucker arrangement that can easily be switched back and forth between 2 tone options.
This is also an amazing choice for kids and guitar novices. It comes in many different colors and it is quite easy to set up and tune. Once you manage to tune it, it will run for a long time. It has four tone modes and you can select one of them using a switch. It has one tone knob adjustment and one volume adjustment. It is quite easy to play and also highly comfortable.
Folks, it's not a Fender that you're buying here. It's a kids guitar made to the scale of little hands. It will hold a tune once you stretch the strings and intonate it. The amp is a little muddy sounding, but that can be corrected by adjusting the volume levels on the amp and guitar. Don't expect Line6 quality! The wood on the neck we received was actually a very good looking cut of wood. Overall, I'm happy with it.
“Photocell Tremolo is found in mid-1960s American amplifiers. Those classic circuits used a light-dependent resistor to attenuate the input signal, coupled with a miniature neon bulb that is connected to the LFO. As the LFO oscillates, the bulb gets brighter and dimmer which in turn varies the resistance of the LDR. The varying resistance works with other circuit impedances to change the signal level, which produces a characteristically ‘hard’ sounding tremolo that moves between two levels, reminiscent of a square wave.” Got that? Well it is tricky and they do sound somewhat different but essentially they produce the same effect. The pedal I am using here, the Fulltone Supa-Trem uses a photocell to produce the sounds found in the classic Fender amps and most common tremolo circuit.
I built me my own custom guitar in high school shop class and it was simple i made an Ibanez RG styled body and a Randy Rhodes/Alexi Laiho styled body just so i can swap the 2 when ever i want and i can say the cons are waaaaaaay over exaggerated cause it was VERY cheap to do it i spent a total of $350 to do it and thats even with the the EMG 81's i have in them. I mean yes its only a 1 pickup guitar on each but its how i want the wood was only $60 for an Ash body (thats for both of them not each) and i have a hook up to get free mahogany that i used on the neck for it and mine noooo one could tell the difference between an actual Ibanez RG or ESP Alexi Laiho's signature guitars the only thing that they were able to know it was custom was the head stock being my signature and the parts that were on it and color option i used is NOT used by ether of them but the time is spot on it took 3 months for me to do them but this was of course all during the course of 45 mins for 3 months so it would of been much faster without it being in school but then again i also sort of cheated with mine cause i have been doing carpentry work since i was 8 so i already knew how to do everything professionally
In 1957, president Sydney Katz introduced the Gold “K” line of archtop and solid body electric guitars[14] to compete with major manufacturers like Fender, Gibson, and Gretsch. The gold “K” Line featured the Jazz Special, Artist, Pro, Upbeat,[18] Jazz II, and Jazz Special Bass. Gold “K” guitars used the same hardware as top manufacturers. However, there were truss rod and neck issues.[citation needed]
Next, squirt your cable and rub it using a clean cloth. To cleanse the amplifier and guitar inputs, compress an area of the clean magazine around a Q-tip. Next, apply a bit of contact cleaner to the cloth, and push it in and out of the inputs to all your guitar gear such as effects pedals, amps, guitar. A point to take note here is that you should use a fresh new section of the cloth for each jack input.
Other high-quality specifications include a bone nut, a molded metal jack plate that is curved and makes plugging and unplugging a guitar cable hassle-free, retooled knobs, fretwire that is slightly smaller than what you’d find on most PRS electric guitars, and PRS’s double action truss rod (accessible from the front of the headstock for ease of use).

“Top shelf” simply refers to any product that is sufficiently uncommon and/or of significantly high enough quality to place it “above” the rest of the “regular” crowd of products. In a shopkeepers parlance, the top shelf was where you placed things that you wished to be visible, but were, in actuality, were rarely sold. The best stuff was kept up and just out of reach of the daily rabble and only brought down when someone who truly appreciates the quality (and is willing to pay the commensurate price) came into the shop.
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: epiphone","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"category","prop11":"electric guitars","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] sub category"}
Fender: Fender guitars are the best example of the old saying “Keep it simple”. They aren’t futuristic, there’s nothing unique about them, they are kinda too simple, their craftsmanship isn’t astronomical but when it’s about outright ruggedness rarely any other guitar comes close to them. Leo Fender designed the Fender guitars to be reliable working man guitars and they still hold true to that quality of theirs. I’m pretty sure if someone buys a good quality Fender guitar (especially the Tele) pretty much his sons, grandsons will still be able to play on that.
Another way to set up your pedals is by placing them within the effects loop of your amplifier.  An effects loop is an audio input and output loop that is placed after the preamp and before the power amp section of your amplifier, using the Effects Send and Effects Return jacks. On some amplifiers, these can be labels Preamp Out (Effects Send) and Power Amp In (Effects Return).  Not all amplifiers have effects loops, but those that do allow for you to place some of your effects within the loop.

I've been coming in since they opened, and it's been crazy cool to watch this little corner shop grow into a major Seattle contender. That's really saying something, as there are some really incredible locally-owned guitar shops in the Greater Seattle Area. As has been mentioned, the service is the selling point. The entire staff are very, very cool people who are perfectly happy to talk shop without trying to push you on a sale. There's a lot of regulars, and combined with the student roster, it definitely has it's own little built in community. Their selection these days is insane, especially since they target a lot of awesome smaller brands that NOBODY else in the area carries. I'm pretty sure this is the only place in town you can go to play the Reverend line, not to mention damn near every PRS model currently in production. The locally-made boutique stuff they stock is awesome too, and I would have never even known about it had it not been for the shop. Kyle, the tech, is an expert. The other guys all do good work as well. This is my go-to shop for basically everything guitar-shop related. And I'm very picky.

A thermally engineered centre block and bracing make this 335 acoustically louder, open and with more clarity. The 'burst top and back also look more modern than vintage, while the translucent dark brown/ almost-black sides and neck-back finish add contrast that creates a classy appearance, along with the nickel hardware. We also get a lightweight aluminium stop tailpiece with locking studs, but this is all-very-classic ES-335 fare, such as the small block inlays and the small fleur head logo. Again, Gibson's build specs tell us we have MHS 'buckers and here the 'Memphis Tone Circuit' includes matched pots with a tight five per cent tolerance, with the same 'orange drop' tone caps as the ES-275.  Plugged in, it's like all our Christmases have come at once. There's a more solidbody response here, as you'd expect, and it really pushes out the sound. It's expensive, but as an investment, this is one of the best electric guitars on the market.
The term piezo refers to the use of piezoelectric crystals that transfer vibrations into an electric current. Piezo pickups are inexpensive to produce, and as such are the most commonly found pickup in acoustic-electric guitars. Piezo pickups generally have a bright tone and strong mid-range response, thankfully they are bundled with preamps that help make the sound more like an unplugged acoustic guitar. While there's nothing better than a true miked acoustic tone, sound quality of piezo preamp system's have steadily been improving, which is good for both guitar players and manufacturers.
A chord is inverted when the bass note is not the root note. Chord inversion is especially simple in M3 tuning. Chords are inverted simply by raising one or two notes by three strings; each raised note is played with the same finger as the original note. Inverted major and minor chords can be played on two frets in M3 tuning.[56][74] In standard tuning, the shape of inversions depends on the involvement of the irregular major-third, and can involve four frets.[75]
When jazz guitar players improvise, they use the scales, modes, and arpeggios associated with the chords in a tune's chord progression. The approach to improvising has changed since the earliest eras of jazz guitar. During the Swing era, many soloists improvised "by ear" by embellishing the melody with ornaments and passing notes. However, during the bebop era, the rapid tempo and complicated chord progressions made it increasingly harder to play "by ear." Along with other improvisers, such as saxes and piano players, bebop-era jazz guitarists began to improvise over the chord changes using scales (whole tone scale, chromatic scale, etc.) and arpeggios.[2] Jazz guitar players tend to improvise around chord/scale relationships, rather than reworking the melody, possibly due to their familiarity with chords resulting from their comping role. A source of melodic ideas for improvisation is transcribing improvised solos from recordings. This provides jazz guitarists with a source of "licks", melodic phrases and ideas they incorporate either intact or in variations, and is an established way of learning from the previous generations of players.
Now that we mentioned some of the exotics, it’s time to go back to the roots. Epiphone Les Paul Standard is as old school as it gets. Legendary LP body style that brings a no-nonsense combo of hardware has always been the way to go. I actually have one of these, and after years of playing it keeps surprising me. I’d say it easily punches way above its price range.

This 248 page book is part of a series of similar volumes, including The Guitar Grimoire: A Compendium of Formulas for Guitar Scales and Modes, The Guitar Grimoire: Progressions & Improvisation, The Guitar Grimoire: A Compendium of Guitar Chords and Voicings, and so on. You get the idea. Master a few of these and you’re going to to be in excellent shape.
{"eVar4":"vintage: guitars","eVar5":"vintage: guitars: electric guitars","pageName":"[gc] vintage: guitars: electric guitars: univox","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop2":"[gc] vintage: guitars: electric guitars","prop1":"[gc] vintage: guitars","evar51":"default: united states","prop10":"brands","prop11":"rickenbacker","prop5":"[gc] vintage: guitars: electric guitars","prop6":"[gc] vintage: guitars: electric guitars","prop3":"[gc] vintage: guitars: electric guitars","prop4":"[gc] vintage: guitars: electric guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,","prop7":"[gc] vintage"}
Great Martin Copy from the later 60's This example is a Well Crafted in Japan model with the "orange lable" Nippon Gakki highly collectable now as a great player Martin like player. Great wood...just see the pics WoW! Sitka Soruce Top, Premium AAA Grade Mahogany neck - sides & back...Made by serious craftsmen high degree of skill and well balanced. Nice big Tone as a Martin same type X bracing and is a proven performer. Nicely aged wood and is a wonderful playing 7 sounding vintage guitar equal to many more expensive builders like Martin. This one has a slight stable old top crack as glued and is not an issue anymore...Plays like butta...You will love the sound! .
There’s always been something special about playing a great guitar riff. Riffs that are memorable, get stuck in your head, and that everyone knows are actually in many cases are relatively easy to play. That’s because most people remember simple melodies that they can hum along to. I don’t think many people would be able to hum along to “Through the fire and flames”.
The Guitar Store is not only the best guitar store in Seattle, but the best guitar store in the WORLD. First of all, the staff are incredibly amazing, lovely, hilarious and helpful. My bandmates and I are not the most knowledgable in terms of gear, and the first time we came in wanting to get our first our ever guitar petals, Blake actually drew a graph of sound to explain how guitar pedals worked. They are the absolute best. Helping us out and going above and beyond what staff should be expected to do. Hands down my favorite guitar store in Seattle, great selection, prices and above all the attention to detail and friendly attitude of the staff. Can't rave enough! Definitely found my guitar store for life! Would recommend for all your guitar needs :)

I hope the list is somewhat correct on peoples lists although it is just an opinion! and just a small thought and insight on angus young he might not make the top 50 for me he plays just a few chords and everything sounds the same, he is with a unique voice and a band who was made by bon scot that put ac/dc on the map!! I know of no really good guitar player that names angus young as their inspiration or was influenced by angus young it is just that his work was too simple!!

*We build all of our Custom Shop and Semi-Custom instruments from scratch and on demand - therefore, Custom Shop and Semi-Custom orders are fulfilled in the order in which they were received. These times can vary due to demand and the custom options you choose. Our production/assemble time frame: 20 - 25 working days since our professional Control Team and Supervisor Engineer will ensure that your ordered guitar is top notch considering the fact that this guitar is intricate to assemble and they check very carefully every detail such as the finish, fret work, pickups, strings. And also, they will test the sound quality. We do not rush up the process of manufacturing your guitar since we would like to deliver to you best quality performance.
The DigiTech Whammy is a great example of a powerful pitch shifter. Controlled by an expression pedal in a manner similar to a wah, it gives you the ability to immediately alter the pitch of the notes you are playing. Pantera and Damageplan guitarist Darrell Abbott used and abused such a pedal to get some amazing sounds in his hardcore style of play.
Ibanez 12 string Martin style, vintage Natural High Quality Japanese Ibanez Vintage Guitar ....This example is MODEL# V302 ...And it IS ANOTHER great find this one is in a Natural finish and is a REAL GEM ta-boot and it has a Beautiful aged Premium Solid German Sitka Spruce Top, WoW! what a nice glass like original finish to this one ...again High Grade woods used on this 80's Ibanez AAA Mahogany Sides-Neck & Back "see quality og the grain in the pics" . Lots of volume & is full-and rich tone from this baby.Pics show missing string done while we were cleaning her up they just snapped ... obviously old and so this guitar will come with a brand new set of Martin strings installed for the new owner no worries..... this one is ez to play & stays in tune well. It is a crafted in Japan guitar and it compares favorably to Gibson, Guild or Martin... at a fraction of that cost. Note: we also have a Sunburst V302 in stock in our listings please see that if you prefer the guitar in sunburst. Thank you for your interest, Joe.
Neck-through guitars feature a (usually laminated) neck that, unsurprisingly, extends through the entire length of the body, with ‘wings’ or ‘fins’ glued onto the sides of the body. This gives even more stability to the neck and even more sustain and resonance when played. Neck repairs are, again more difficult and costly. However, the increase in stability means these repairs are much less likely to be needed.
After Spanish guitar manufacturer Ibáñez e Hijos was bought by Telesforo Julve in 1933, Hoshino Gakki, who used to import these guitars to Japan, decided to build them himself under the brand name Ibanez Salvador, which would later become Ibanez. In the 1960's and 1970's, the production was limited to Gibson, Fender and Rickenbacker copies (and the associated legal proceedings). But in the 1980's and 1990's things started to get serious thanks to guitar players like Steve Vai and his famous JEM. Also noteworthy is the birth of the Universe model and the more affordable RG series, which are leading products in the "Super-Strat" market segment today. Even though Ibanez also builds quality hollow-body guitars for famous endorsers (Pat Metheny), the brand has become a reference among metal heads and shredders. Ibanez guitars have a very fast neck and usually pickups with a high-output level to go with it.
Now you should have all you need to assemble your first effects pedal. Make sure you have a clean, well-ventilated area to work. Wash your hands before you start. If you like, wear some conductive nitrile gloves. Avoid handling components any more than necessary. Contaminants on the components and PCB will make them harder to solder and can cause reliability problems. Certain IC’s can be damaged by static electricity from handling. Solder is hot and creates dangerous fumes so be careful. Follow the instructions carefully, in particular making sure you insert components in the correct places and the correct way around. Many components look alike and some are polarity sensitive, so take your time to get it right. Solder one pin of a component and then double-check it before soldering the rest. It’s much easier to move or remove a component with only one lead soldered to the board.
Ibanez is a Japanese guitar brand, which is established in the year 1957. They provide Acoustic, Bass Guitars and Semi-Acoustic Guitars at different price segments. The company is owned by Hoshino Gakki. Their headquarters located in Nagoya, Aichi, Japan. They also manufacture amplifiers, mandolins and effect units. They become one of the top ten best guitar brands in India. The price range starts from Rs. 13,299/- onwards (approx). For further details, visit
When it comes to guitar amplifiers, especially the ones that we love here at PMT, “cheap” doesn’t mean poor quality! Thanks to huge leaps in manufacturing processes, stringent quality control and the fact brands really care about the products they create, you can spend far less on an amplifier and musical instrument these days and still get a fantastic, highly playable and superb quality option for your needs.
The Old Standby is another model beloved by generations of harmonica players. Up until the 1990s, this model was a quality instrument made in Germany on a wood comb. Where the Marine Band was the choice of blues players, many country music players such as Charlie McCoy preferred the Old Standby. In the 1990s, Hohner began manufacturing this model in China on a plastic comb with a significant decrease in quality. Among harmonica fans the downgrade remains unpopular.[26]
You can hear one all over Led Zeppelin’s debut record and all over Jeff Beck’s trademark “Heart Full of Soul” intro riff from the Yardbirds. He also used it extensively on the Jeff Beck Group sessions. Of course the most famous fuzz pedal is the Dallas Arbiter Fuzz Face. This pedal was favored by Jimi Hendrix and set the benchmark for fuzz tones that we are still chasing to this day.

I have been watching Marty, subscribe to many, but found Jonathan Kehew also a very good teacher with longer than most videos and a calm organized presentation . Would like to see what anyone thinks about Swift guitar lessons. I stated using his site as he allows downloads of pdfs of scales and other written material to accompany the videos. He also has three camera in camera closeups of chords and hand position. His appearance clothes, pale skin, open neck shirt, facial hair is a turn off but his content is good I think.

Very disappointed! This was a gift from Santa this morning and the amp failed miserably. Would not work at all. Not with a battery or an adapter(which by the way is not included). Amp started to smell like it was burning/melting even though it showed no power at all. Son is very disappointed to say the least and so is mommy. Only thing he wanted was an electric guitar and he couldn't even enjoy it this morning. How do I explain returning it to Santa...
Sturdily constructed with a solid basswood body, bolted maple neck and rosewood fretboard, this black electric guitar has an attractive glossy finish. The list of add-ons include a high quality Hollinger BC-08 practice Amplifier (10 Amp), string-winder cable, strap, gig bag and pitch-pipe picks. The intonation as well as playability of the Davison full size electric guitar has been enhanced owing to its single, high quality humbucker pickup, chrome bridge system and diecast tuners. Last but not the least, the practice amp is suitably equipped with a headphones jack for noise-free practice sessions, as well as an overdrive mode for cool distortions!
I built me my own custom guitar in high school shop class and it was simple i made an Ibanez RG styled body and a Randy Rhodes/Alexi Laiho styled body just so i can swap the 2 when ever i want and i can say the cons are waaaaaaay over exaggerated cause it was VERY cheap to do it i spent a total of $350 to do it and thats even with the the EMG 81's i have in them. I mean yes its only a 1 pickup guitar on each but its how i want the wood was only $60 for an Ash body (thats for both of them not each) and i have a hook up to get free mahogany that i used on the neck for it and mine noooo one could tell the difference between an actual Ibanez RG or ESP Alexi Laiho's signature guitars the only thing that they were able to know it was custom was the head stock being my signature and the parts that were on it and color option i used is NOT used by ether of them but the time is spot on it took 3 months for me to do them but this was of course all during the course of 45 mins for 3 months so it would of been much faster without it being in school but then again i also sort of cheated with mine cause i have been doing carpentry work since i was 8 so i already knew how to do everything professionally

With over 8 decades of development, the electric guitar and music from guitars is getting progressively more sophisticated. Nowadays there are thousands of models available, from a number of manufacturers; electric guitars come in all kinds of shapes and sizes – some reminiscent of the regular acoustic guitar, and some drastically different from the traditional instrument. Regardless, there's a number of features which are invariably present in practically every electric guitars: the headstock, neck, body and strings. The headstock includes the machine heads, truss rod (may not be used in all models), string guide and nut; this section is used for tuning and holding/adjusting the strings. The neck serves the function of supporting the strings, and it's comprised of a fretboard, the inlay fret markers, the actual frets and a neck joint. The body of the guitar is comprised of several mechanisms including the pickups (neck and bridge), saddles, tuners, pickup switch, control knobs (tone and volume), output connector and strap buttons – sometimes others, in more sophisticated models. Finally, the strings are usual divided in brass and treble variants.
The Firebird did have some other unique features such as its banjo style tuners and mini humbuckers that produced a different sound than the full humbucker pickups Gibson typically offered.  Many notable players preferred the Firebird: Mick Taylor from the Rolling Stones used it on the album Exile on Main St.  Allen Collins would also use this axe on stage with Skynyrd alongside his Explorers.  The great Texan blues guitarist Johnny Winter was known for playing slide on his 1963 Firebird to great effect.  Dave Grohl, of Nirvana and Foo Fighters fame, used his white Firebird to create a modern rock sound.
Started similarly to PRS, Taylor was a brand that began out of passion and the back of a car. In 1974, friends and coworkers Bob Taylor and Kurt Listug joined together to purchase American Dream, the guitar making shop for whom they both worked. Geared toward producing the most high-quality USA made acoustic guitars they could muster, they changed the name of the business to Taylor Guitars, as it sounded more “American” than Listug. Though they went through some financial troubles initially, the brand eventually grew into what they are today: the number one manufacturer of acoustic guitars in the United States. They’ve also taken it upon themselves to pioneer a business model based around sustainable practices – Bob even goes so far as to travel to competitors to share with them said practices, understanding that, in order for guitar builders to continue to flourish, everyone needs to be an active participant in taking care of the environment. Or else there might come a time when there’s no more wood with which to build guitars. And that makes the El Cajon, California-based brand even mightier.
So I was all, "oh no...I want this one." So I did leave with it, and without even asking they sold it to me at less than the price on the thing because it was the demo and had a tiny belt buckle type scuff or two on the back. I think I actually wound up saving a few hundred dollars. I don't know if they figured a percentage of the total should be knocked off, or what.
If you never intend to do octave high vibrato bar stuff or play music in the style of bands like PANTERA (hard, fast metal, with lots of high note bending leads), or Jimi Hendrix (psychedelic rock), then exclude any floating or fancy bridge (also called a tailpiece). Non-floating tail pieces are usually more stable (keeping tune and intonation) and cheaper to buy.
One of the more common questions beginners have is why even bother with reverb pedals when most modern amps have a built-in version of this effect? To be honest, if you have a vintage tube amp with an actual spring reverb inside, there really isn’t a good reason to go with a pedal. However, most don’t. The thing that makes reverb pedals a much better solution in most cases is that you get a level of quality that can be used on stage.
"Emulating guitar sounds is problematic – or it was until Impact Soundworks launched Shreddage. Version 2 for Kompact 5 is rammed full of chords and articulations to get the most authentic sound possible […] The quality of the samples here is really good. Although aimed at Rock and Metal, it lends itself to any genre. For those more accustomed to keys than strings, it is ideal with its impressive soundset and amount of control." CM Reviews (Computer Music)
A more successful early electric was the Ro-Pat-In "Frying Pan" guitar. This was played lap-steel style, and was the earliest I know of that uses something close to the magnetic pickups as they exist in modern guitars. This was conceptualized by George Beauchamp in 1931... he played Hawaiian style, thus the lap steel design. He met Adolph Rickenbacker and together the two worked out the details of the pickup system, and put this into production in 1932... the company name was eventually changed to "Rickenbacher".
Setting up a mic to record the natural acoustic sound of the guitar strings can add percussive character when blended with the amp sound, especially if you are capturing old-school archtop sounds. For best results, the guitar needs to be isolated from the amp to prevent excessive bleed. This technique gives a good front-end attack to the sound and plenty of definition. A small condenser is the best mic for the job, and it’s worth using a high-pass filter as well.
I keep coming back to this point because it’s absolutely essential: learn how to solo over chords. I don’t mean simple chord arpeggiating, even though that has its place, too. If you can follow the chord changes with smooth, soulful playing, you will never be fenced in. You can drop into any style, any band, and any situation. Most of us get stuck playing a given scale pattern for years before something shakes us up. Make this the foundation of your learning with this book.
Gibson Les Paul specifications during 1958–60 varied from year to year and also from guitar to guitar. Typical 1958 Les Paul Standard necks had a thicker “club-shaped” neck, thinner frets and lower fret height, which changed during the course of 1959 to develop into typical 1960 necks with a thinner cross-section and wider, higher frets. Les Paul Customs from the same period had totally different frets and were referred to as “The Fretless Wonder”, which were designed for jazz guitarists with thick flat-wound strings.[note 7][note 6]
The whole point of having a DIY guitar kit is to build a guitar that you like, so make sure that you get one with you're preferred shape and profile. Kits with classic guitar body shapes are the safest choice, as evidenced by their continued popularity in the market. But don't limit yourself with just the familiar, spend time looking at other designs to see if you're missing out on something cooler, something that better matches your personality.

Rickenbacker is another famous American brand created in 1931 to build Hawaiian guitars, called "Frying pans" due to their typical shape. The brand incorporated guitars to its catalog a bit later. The models created by Roger Rossmeisl (Combo 4000 guitar, 4000 bass), a former Gibson collaborator and future Fender man in the 1950's, enjoyed a lot of success and became the brand's most typical designs. The 360, 370, 620, 660, and 4003 models can be connected to a Rick-O-Sound unit (a box with two mono outs) via a stereo 1/4" jack, which allows the two or three pickups to feed different amps. Most instruments have a dual truss rod and a varnished rosewood fretboard. Their distinctive jangle and chime emphasizes high frequencies, giving pretty good results with clean sounds. The Beatles, and especially John Lennon, often played Rickenbacker guitars at the dawn of their careers. Tom Petty, The Jam and R.E.M. are also Rickebacker users.

{ "thumbImageID": "ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst/J57125000001000", "defaultDisplayName": "Alvarez ABT610E Baritone Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51500000217496", "price": "399.99", "regularPrice": "399.99", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Alvarez/ABT610E-Baritone-Acoustic-Electric-Guitar-Black-1500000217496.gc", "skuImageId": "ABT610E-Baritone-Acoustic-Electric-Guitar-Black/J57125000002000", "brandName": "Alvarez", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Shadow Burst", "sku": "sku:site51500000054240", "price": "349.99", "regularPrice": "399.99", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Alvarez/ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst-1500000054240.gc", "skuImageId": "ABT610E-Baritone-Acoustic-Electric-Guitar-Shadow-Burst/J57125000001000", "brandName": "Alvarez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }

Electric guitar design and construction vary greatly in the shape of the body and the configuration of the neck, bridge, and pickups. Guitars may have a fixed bridge or a spring-loaded hinged bridge, which lets players "bend" the pitch of notes or chords up or down, or perform vibrato effects. The sound of an electric guitar can be modified by new playing techniques such as string bending, tapping, and hammering-on, using audio feedback, or slide guitar playing. There are several types of electric guitar, including: the solid-body guitar; various types of hollow-body guitars; the six-string guitar (the most common type), which is usually tuned E, A, D, G, B, E, from lowest to highest strings; the seven-string guitar, which typically adds a low B string below the low E; and the twelve-string guitar, which has six pairs of strings.