On some amps with a number of input and output jacks, the jacks may be consolidated in a patch bay. Some amps have an input jack for a foot-operated switch which can be used to turn on an effect or switch to a solo channel. Some higher-end amps have a Speakon speaker jack for an extension speaker. In the 2010s, the Speakon jack is often used in high wattage amplifiers, because the design of the connector, which is shielded from human touch, prevents electrical shock from a high-powered amplifier. Some amplifiers have a "tuner out" jack, for sending the instrument signal to an external electronic tuner. Bass speaker cabinets often have two 1/4" jacks. These are provided so that one speaker cable can be plugged into the first jack and connected to the power amp; if the bassist wants to use a second cabinet, a second speaker cable is plugged into the second jack and then into second speaker.
Description: Body: Basswood (Tilia, Linden, Lime) - Neck Attachment: Bolt - Neck Wood: Maple - Neck Construction: U-Shape - Nut Width: 42mm - Fingerboard: Rosewood - Frets: 24, Jumbo - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Cutaway: Single - Hardware: LTD Tuners, Chrome, 2x Volume Control, 1x Tone Control, 3-Way Switch - Circuit Type: Passive - Pickups: ESP LH-150N/LH-150B - String Instrument Finish: Silver Sunburst
In the late 1950s, Guitarist Link Wray began intentionally manipulating his amplifiers' vacuum tubes to create a "noisy" and "dirty" sound for his solos after a similarly accidental discovery. Wray also poked holes in his speaker cones with pencils to further distort his tone, used electronic echo chambers (then usually employed by singers), the recent powerful and "fat" Gibson humbucker pickups, and controlled "feedback" (Larsen effect). The resultant sound can be heard on his highly influential 1958 instrumental, "Rumble" and Rawhide.
Another clarification about brand names is in order. Teisco guitars can be found mainly bearing at least eight brand names: Teisco, Teisco Del Rey, Kingston, World Teisco, Silvertone, Kent, Kimberly and Heit Deluxe. Teisco was the name used mainly in Japan but also on a few occasions here in the United States. Most Teisco guitars were imported into the United States by Chicago’s W.M.I. Corporation � originally owned by guitar importing pioneer Jack Westheimer � bearing both the Teisco Del Rey and Kingston brand names. By the mid-’60s W.M.I. was providing Teiscos to Sears and Roebuck carrying the Silvertone moniker. I’m not sure the World Teisco brand ever got to the U.S.; my guess is that it was an export designation that went to other markets. Some of the early Kent guitars imported by New York’s Bugeleisen and Jacobson were purchased from Teisco. The distributors responsible for either the Kimberly or Heit Deluxe brand names remain a mystery at this time. It is possible that you may encounter other brand names on Teisco-made guitars sold through other distributors, but these will be in a minority. If you know of any other names, please let us know.
This POD 2.0 comes with the unit, power cord, and the live stage footswitch! CAT cable to interface between the POD and FBV foot switch included. Everything is in very good condition! Pictures are part of the description, if you have any questions feel free to message me for more details! From Line 6 web page The industry standard for direct recording in the studio, POD ® 2.0 delivers the tones heard on hit records everywhere. For practice, it's the ultimate way to get inspiring, stage-perfected tones with headphones. In the studio, you can become more productive and creative. You can instantly get the sounds you need! Absolutely No International Shipping Whatsoever, only buy if you live in the mainland USA, No shipping overseas.
Comfort is at the top of the SUB Silo3’s priorities. Its curvy body has contours in all the right places, its asymmetrical neck profile—it’s slightly slimmer towards the treble strings—feels natural in your hand, and even the vintage-style tremolo bridge has a flat surface to rest your palm on. Add a light basswood body, and you’re ready to rock for hours on end.
For subtle modulation just set every knob at about 11 o'clock. You'll get a thin, shimmering layer over your acoustic guitar's tone that doesn't drown out the natural resonance of the instrument. The pedal doesn't boost your signal or add any kind of volume. All you'll hear is a clear, simple effect. Additionally, the CH-1's two stereo outputs allow you to easily split your signal between two amplification sources. Simply plug your primary source into output A (mono) and the secondary source into output B.
The focus has always been to start with sound and top it off with a bold, boutique-inspired appearance. When Michael Kelly launched, we, in fact, only offered mandolins and acoustic basses. These two markets had been under served and consumers could not buy a great sounding instrument without breaking the bank. The Michael Kelly Dragonfly collection of both acoustic basses and mandolins quickly became popular and hard to get. Musicians were drawn to their decidedly custom appearance and then fell in love with their sound and performance.
Why does the material matter less than with an acoustic guitar? Because the body of an electric guitar is much less important in producing and amplifying the sound; all it really has to do is hold the strings so they're long and tight enough to make the kind of sound frequencies we want to hear. Although resonance still plays an important part in giving an electric guitar its tone, solid-body electric guitars generate most of their sound through an entirely different process from acoustic guitars. In fact, even though acoustic and electric guitars look similar, and you play them in a broadly similar way, they are quite different instruments.
Add a maple top to the mahogany body, as do a great many Les Paul models, and a blend of characteristics comes forward. The mahogany’s depth and richness remain, but the maple provides added snap, clarity, and definition. It also tightens up the lows and adds more cut to the highs. For many players this sonic evolution is highly desirable, whereas others might prefer the smoothness of the pure-mahogany design.
The guitar features hand-rubbed solid Sitka Spruce top supported by Martin's incredibly reliable mahogany HPL (high pressure laminate) back and sides, essentially similar to the configuration found on many of Martin's mid-priced acoustics. If you're looking for an affordable starting instrument that has big-brand backing, or you are looking to get into the parlor-style guitar trend, check out the LX1E Little Martin.
If it helps, Schaller have very accurate drawings of all their hardware on their website. You can also get very good drawings of all Gotoh parts as well, but theirs are harder to find (hidden in the parent company's site and I can't recall the full details). It is worth having a look at those, and pay attention to the way the tuning posts are shaped. That radiused section turned into the post is important , it really helps lock the strings firmly.
Finally, if you’ve been looking around at different instruments you may have noticed some really cheap guitars by brand names you’ve never heard of. I always recommend starting out on a quality guitar made by a company you can trust. However, I’m also not going to look down on anyone who has to get something less expensive because it is all they can afford.
Every guitarist who bends or vibratoes a string to make it sing owes a debt to B.B. King. With influences as diverse as T-Bone Walker, Charlie Christian and Django Reinhardt, the late guitarist turned the blues world upside down in 1952 with “3 O’Clock Blues.” Almost overnight, the harmonica was supplanted as the primary solo instrument in blues, as guitarists scrambled to imitate B.B.’s soloing style, especially in Chicago.
Because of this, the VI opens the door for critique at the smallest degree, but I couldn’t even get that far before finding problems. The strumming is so terribly robotic out of the box, and the sounds divided among the four guitars (Fender Stratocaster and Telecaster, and “bright” and “normal” versions of a Duesenberg StarPlayer) aren’t screaming authenticism either.
These two articles show us how me can manipulate coil winding direction, electrical phase, and magnetic polarity to achieve hum-cancellation between two coils. Having this knowledge allows us to create hum-cancelling combinations of coils over and above than just using humbuckers. A good example is using a RWRP pickup in the middle position of a Strat.
Many guitars (even new guitars) need the frets leveled in order to play buzz-free with low action. Most electric guitars with bolt-on necks come from the factory with high tongue frets. Doing great fret work is a learned art, and I guarantee that you will be happy with mine. All my fret work jobs are performed with the guitar mounted in a neck jig that simulates string tension. This allows very accurate work. Re-fret jobs include leveling the fretboard if needed.
As a trained engineer I just don’t see how contemporary luthiers would be able to control only these three parameters in combination in order to make up a specific tone. There is simply no connection between these and the sonic impact they have–again, in combination. Did anyone ever change the shape due to the wood he uses? For instance wood would be lighter by 5%, stiffer by 8% (which would be very much, by the way, but it happens all the time even with the same species) so consequentially make the horn less thick by 3% and trim the tail by 5 mm. A rule like that would be plausible in case wood would affect the tone that much. But luthiers never do. Thy do not even take care of weight and stiffness.
The more solid wood there is, the better the overall resonance, sustain and tone of the acoustic guitar. Solid wood, specially those used on the tops of acoustics, also resonate better as it ages. The downside to solid wood is mainly its more premium cost, and not to mention it uses more wood resources than laminate wood. Solid wood is also more prone to damage, so they require extra care especially from changing weather and humidity. Laminate woods are more affordable, and they are also more sturdy and resistant to damage. On the flip side, they will lack the resonance and sustain of solid wood, but this can be a good thing if you're looking for vintage mid-range focused tone.
If you already have an electric guitar and you're looking for replacement strings, carry cases, guitar stands, or other accessories, you've come to the right place. Amazon.com offers a selection of tools and accessories designed for players of every age and skill level, from beginners to pros. Look for amplifiers, cables, and microphones too—you can enjoy great selection right here online, with no need to make a special trip to the guitar shop.
We are your Vintage Pickup specialists. We have cornered the market of manufacturing the most accurate vintage pickup reproductions to which can not be equaled. Our process is to chemically analyze an original pickup magnets and wire, then we reproduce them with the exact same magnets and wire. We don't use stock magnets or wire. We don't degauss magnets and say they are vintage. Our magnets are only as strong as the elemental composition will hold. Our wire is specially manufactured for us, we have many batches of wire with all different types of resistances and O.D.'s. Our wire also is processed differently than modern conventional wire, these little details are what makes the Klein Pickups Reproductions the most accurate in the world. We have a full array of models that we reproduce. Check out our site for the full list of all of our offerings. As a small business we always appreciate your business & support. -Thanks
Pacifica series of Yamaha electric guitars are the ones you have probably heard of once, mistaken for a Strat a couple of times, but never really considered. Needless to say, that was a mistake. One quick look at Yamaha Pacifica PAC510V OVS reveals why. Before even getting into details it doesn't take much to recognize the apparent quality all around.
The fully hollow body electric guitar is almost always a finely crafted work of art. These instruments are a throw back to the days of hand shaped acoustic instruments of yesteryear. The hand carved archtops and backs are designed to take advantage of pure acoustic detail, such as resonance and tone, while the electric aspect allows the performer to be amplified. A pure traditionalist could ask for nothing better tone wise, but must contend with other aspects of these incredibly resonant instruments.
The next step is to figure out what gauge, or thickness of string is best suited to your playing ability and style. Thinner gauges are easier to fret and bend, and may be better suited for beginners, until callouses build up on the fingertips. Heavier strings tend to produce greater volume and fuller tone. Nylon strings are typically categorized as light, medium or heavy tension. Steel strings for both electric and acoustic guitars are categorized by the gauge, or thickness of the lightest string, the high E string, measured in thousandths of an inch, with .09 being a common size for an electric set. A set of electric strings may be labeled .09-.042 - this is the gauge of the lightest and heaviest string in the set. Acoustic sets are a little thicker, so a typical medium-gauge set might be .012-.054.
Your guitar is a model H1213 Archtone made in 1963. Harmony did a great job of stamping model numbers and dates of manufacture on their guitars, but they often require some decoding. The F-63-HB is the date code and the two numbers, not surprisingly, indicate 1963. The “F” preceding the year was often thought to be a fall production indicator while the other letter stamp they would use was an “S,” which researchers thought stood for a spring production instrument. However, a former Harmony employee notified a Harmony database website that it is more likely an “F” stands for “first” and “S” stands for “second.” He explained that Harmony would shut the factory down for two weeks in July and that guitars produced before this break were stamped “F,” while guitars produced after were stamped “S.” The H1213 is the model number as indicated in Harmony’s catalogs and literature. The “3714” is the serial number of your guitar, but little information has been uncovered as to what this series of numbers represents. More than likely, it was a consecutive production number of that particular model for either the first or second half of the year.
Makers of the Elk badged guitar from the early to mid 1960s to 1975, although other sources indicate that the Elk brand did not stop production until the early 1980s. Elk badged guitars came in clear acrylics in addition to colors in the early 1970s, which was an attempt to copy clear acrylics designed by the legendary Dan Armstrong in the late 1960s.
The second issue of the Les Paul guitar was introduced to the public in 1954. Called the Gibson Les Paul Custom, this entirely black guitar was dubbed the Black Beauty. The Les Paul Custom featured a mahogany top to differentiate the instrument from its Goldtop predecessor’s maple top. It also featured the new Tune-o-Matic bridge design and a pickup with an alnico-5 magnet, P-480, in the neck position. In addition, since 1957, the Custom was fitted with Gibson’s new humbucker pickups, PAF, and later became available with three pickups instead of the more usual two. The three pickup model retained the standard Gibson 3-way switch so not all pickup combinations were possible. The neck and bridge-only settings were retained, but the middle switch position was set to enable the middle and bridge pickups. A common modification was to restore the standard neck/both/bridge switching combination and add a switch to enable the middle pickup on its own. The guitar is wired as a “normal”2 pick up Les Paul except there is a master volume , master tone, (for front and back pu) while the middle pick up has its own volume / tone. this allows the middle pu to turned out of the circuit or mixed with the other two. allowing many different tones.
I will not take my guitars anywhere else. You just do not get better, more professional service than at Franklin Guitar. I have played guitar for a long time and I have been in hundreds of guitar stores, and this is one of the best. You won't get the "hey don't touch that" or they "what's it going to take to get you into one of those guitars?" treatment. You get treated like a valued customer. Also a lot (most) of independent guitar stores have terrible assortments of guitars for sale, but not Franklin Guitars. They have a great variety of quality instruments. Plus, they have some really cool, unique guitars. A place like this is so rare nowadays.
No matter whether you used method A or B, you can now go about measuring the neck bow. This is done by measuring the string height (the gap between the ruler/string and the top of the fret) at about the 8th fret. There is a lot of debate over how straight a neck should be, and in fact it really is personal choice, but a height roughly the same as the thickness of a B string is a good starting point. Personally, I use a 0.012” feeler gauge to do this, but you could use a B string. Simply slide the feeler gauge/B string into the gap to see if it is too big/small.
Semi-hollow body electric guitars are basically a middle ground between a solid body electric and a fully hollow body electric guitar. Jazz, country, and rock guitarists alike may gravitate towards semi-hollow body electric guitars for several reasons. One of the main reasons is that semi-hollow body guitars still produce that rich, resonant sound of a hollow instrument, but they typically have a solid or sometimes chambered center block in between the top and back. This design helps fight off that unwanted body-resonant feedback we spoke about before while even adding some extra sustain. Gibson offers a wide selection of semi-hollow body electric guitars, which include the iconic Gibson ES-335. Guitar brands such as Gretsch and Ibanez are also widely recognized for their semi-hollow body electric guitars.