The term piezo refers to the use of piezoelectric crystals that transfer vibrations into an electric current. Piezo pickups are inexpensive to produce, and as such are the most commonly found pickup in acoustic-electric guitars. Piezo pickups generally have a bright tone and strong mid-range response, thankfully they are bundled with preamps that help make the sound more like an unplugged acoustic guitar. While there's nothing better than a true miked acoustic tone, sound quality of piezo preamp system's have steadily been improving, which is good for both guitar players and manufacturers.
Tablature, or Tab, is a very important tool that allows guitar players to easily learn how to play chords, melodies, and songs. Learning how to read guitar Tab can be a mystery for some newer guitar players. In this guitar lesson, we are going to learn how to read guitar Tabs and go over some of the more common elements you will see when you pull up a Tab for a song you want to learn. Try this lesson if you want to learn how to read guitar sheet music.

When we take a look at a guitar neck, it is important that the guitar is under string tension and in playing condition when measured. The PLEK measures the instruments neck and fret height with the instrument strung up to pitch. The computer ascertained a 3-D like graph of the fret board surface, including the position and height of the strings. Thanks to the PLEK SCAN the relief of the neck made by the string tension is taken into account while calculating the process-parameters. The operator then has the ability to manipulate the parameters to give the player an optimal playing instrument.

Before we begin, it should be pointed out that some time ago Guitar Player presented the history of Teisco, based on information painstakingly translated from a Japanese article penned by Mr. Hiroyuki Noguchi of Japan’s Rittor Music, editor of the Guitar Graphic book series. Unfortunately, the article used for reference was an older piece which has subsequently been totally revised and corrected by Mr. Noguchi based on later interviews with principals in the Teisco company. Some of the chronology in the GP story is inaccurate. What follows here is the latest and most accurate information on Teisco (in regards to company history), confirmed in repeated direct communications with Mr. Noguchi in Japan. This information also supersedes some incorrect facts in my own essay on Teisco Del Rey Spectrum 5 guitars in the first issue of Vintage Guitar Classics.
So I visit a Guitar Center, wild eyed in wonder at the vast array of choices now available. I start at the bottom end of the Strat food chain and go up. I had to reach a $1500.00 Eric Clapton Signature Model to find a guitar equivalent to the 200 dollar Mexican Strat, my dumbass had given away. (I didn’t think a 200 dollar guitar had any resale value.)  Firmly intended to compete with Gibson's ES-335, the Starfire IV, V and VI retain plenty of Guild style, not least the more spacious cutaways and the wooden foot tune-o-matic-style bridge. Placed side-by-side with an equally new Bigsby-equipped Gibson ES-335, the Starfire V somehow looks more 'retro', more 60s. The body here is made from mahogany laminates with a distinct striped figure under the Cherry Red finish, which was introduced with the first Starfire. Then, as now, it all creates a different aesthetic to the Gibson ES-335. A major difference is the control set-up, which here augments the Gibson layout with a smaller knobbed master volume control on the treble horn, just behind the three-way toggle pickup selector. The pickups here replicate the early-60s introduced 'Anti Hum Pickups' and are period correct, along with the black plastic, chrome-tipped control knobs. It's a fairly weighty guitar for a semi, thanks to the full-length maple centre-block, and has a classic strapped-on feel. It is, of course, thinline depth and feels every bit an ES-335. It has a 'clean' sound, with low-end definition, slightly bright on the treble pickup with decent sustain and, importantly, a very respectable feedback threshold. It likes volume, and while similarly evocative of virtually all those classic styles, it's the stage version and effortlessly takes you on to early The Who, The Jam or Britpop voices, while seemingly equally at home with rootsy, strummier Americana. Decca's flat-top acoustic guitars seem to usually sell for$50-75. They're not highly regarded because (a) acoustic guitars don't have the collecto-mania of electric guitars, except for certain brands (Martin, Gibson, etc.), and (b) the tonewoods Decca used were inferior to solid spruce as used by the aforementioned makers. Indeed, Decca often used plywood, which doesn't yield very good tone in an acoustic.
The Fender Hot Rod Deluxe or its big brother the Deville come to mind. I have a hot Rod Deluxe tube mode 40 watts and it really pumps out the volume. The simple foot switch allows four settings from clean, mean, beyond mean and in your face. It really makes slide guitar sound like a male cat calling to a female in heat. Also, it can be mellow. I have seen many youtube videos with Eric Clapton playing a Tweed Model. I also own a Line 6 Duo Verb, Line 6 DT50, and of course and old US Made Peavey 5150 Eddie Van Halen Signature Model. The Peavey really pumps up the heat and the sustain is as wide as the Grand Canyon.
I think that a good EQ in the loop is awesome. If you find an amp that has a great overall sound, but you wish that it was a bit brighter, darker, etc, but you find that you loose the character of the distortion when you get the tone you like you can play with both EQs to have a lot of controll over the final sound. It won't make up for a crap amp, but it can make a great amp a whole world of awesome.
The brands we talked about today are considered to be the most trusted on the market. Even so, you might want to skip the bare-bones entry level models as those are bound to come with a flaw of some sort. We showed you a number of guitars from each of the brand’s current lineup. Those represent well rounded and balanced choices for beginners and intermediate players alike.
I got this lyle acoustic (w-400) for $40 at a yard sale - it is THE MOST INCREDIBLE GUITAR you could ever ask for - looks just like a martin d-18 - solid spruce top - sweet figured mahog b&s's - back of headstock even has the valute like a martin - just kicks my buddies real d-18 to pieces - he's so jealous - if you get the chance to own one don't pass it up - it will probably be too cheap to pass up and you WILL regret it later (like I have been kicking my own ass for decades for passing up a 60's Gibson byrdland for$400)


We gave our electro-acoustic chart a big refresh to keep it relevant for early 2018, by replacing a few older guitars with some excellent upgraded models. Guitars such as the Epiphone PR-4E and Mitchell MX400 were removed, and in came the exquisite Yamaha A Series A3M, the new PRS SE A50E, the cool Fender Sonoran SCE, and two solid budget models, the Kona K2 and Yamaha’s APX500III.
To answer your question directly, yes, but only from a strictly physical point of view. According to guitar enthusiasts, electric units are easier to handle than their counterparts. The main motif for this has to do with the fact that the acoustic models come equipped with what many describe as heavier gauge strings. Because of this feature, their strings are more difficult to pick and press down.

The 2008 Les Paul Standard is one of the first models from Gibson USA to utilize the revolutionary Plek machine in setting up the guitar. The Plek is a German-made, computer controlled machine that carefully measures each fret, along with the fingerboard height under each string, and then automatically dresses each fret, virtually eliminating string buzz and greatly improving the overall playability of the guitar. This pioneering process does in minutes what it takes a luthier several hours—sometimes even days—to accomplish. Every fret is accurately aligned, and the guitar is properly intonated, leaving the instrument “Plek’d” and amazingly playable.
Clearly, when playing live rather than recording, the room you are in will create its own reverb. Live performance spaces are often prepared with a combination of acoustically absorbent and reflective materials to achieve the desired balance. Sometimes this means hi-tech purpose made fittings made of special materials. Often it's just judicious arrangement of curtains and rugs, combined with bare walls.
Input kewords into the searchbox at the top of each page, then click the WHAT'S IT WORTH button. The search engine will find matching pages based on keywords you type into the Search Box. The engine searches all categories of objects, not just this particular category, so you may get some irrelevant items in your search results. Too many results? Be more specific. Not enough results? Be less specific.
I think Matts’ advice is good, (old guitar strings can be helpfull for “fishing”) but if you change your p’ups and switching often an accessible control cavity is a great thing, just be sure to drop all pots and such into the body and drill through the potentiometer holes so you know where to place template and assure router bit won’t hit anything dangling in the body.
4) Aside from enough publishing errors that, to my sensibilities, mean that the book is not ready to be published, instructions are shown on how to add a Varistor switch to a guitar, and a Les Paul is used for the example. The drilled hole given as the example is nothing less than a hack job, I hate to say it, but it is. I would faint if I saw a tech do that to my guitar. Besides its being really bad advice in the first place, if you are going to do it, DONT follow this example!
Description: Body: Mahogany - Top Wood: Maple - Quilted - Neck Attachment: Neck-through - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Maple - Frets: 24 - Inlay: None - # of Strings: 6 - Scale Length: 27" (69cm) - Headstock: 7 In-Line, Reverse - Bridge: Floyd Rose Style Locking Tremolo - Cutaway: Double - Hardware: Black, 1x Volume Control, 1x Tone Control, Grover Tuners - Circuit Type: Active - Pickups: EMG 707 - Pickup Configuration: H-H - String Instrument Finish: Tribal Purple, Black flame, Tribal Green, Blue Quilt, Satin Natural, Blue Flame
Above here's a blast from the past. The reissue of the 1960's Harmony Stratotone H49 Jupiter. Originally this guitar was manufactured in Japan, but these babies came straight from China many years later. They copied them right down to the T including those Gold Foil Pups. Guitar is hollow body and has a volume, volume, tone, tone, master tone knob, with a really cool 3 way switch. They don't come up on Ebay to often and this ones like brand new but was briefly used. Sold

#### Similar to the hollow body, the semi-hollow body has more resonance than a solid body. However, semi-hollow guitars are designed with a solid center wood block that adds stability and sustain, and helps cut down on feedback. Many blues players like the warmth of the semi-hollow and the increased attack and sustain offered by the center block. Semi-hollow guitars can be great for a wide variety of music - from blues and jazz to punk rock.

##### Pressing a string against a fret reduces the vibrating length of that string to the distance between the pressure point and the bridge, thereby controlling pitch. On nearly every Western fretted instrument, the distance between frets is a semi-tone of equal temperament, assuring the easy achievement of strong sounding chords and single notes that fit our hemisphere’s usual expectations for rhythm sounds and melodies. Understanding the virtues and limitations created by the order of frets opens up the door to ways to escape their constricts, like bending strings, playing slide, using whammy bars, delving into extended technique or trying fretless instruments.

12. Once your wiring loom is complete, install it in the guitar, and reattach the pickup and ground wires. Test the guitar through your amp and make sure everything is working. If it is, congratulate yourself on a job well done. If it’s not, check that you’ve wired everything together properly. Also, check your solder joints and redo any that aren’t shiny or look a little iffy.
I bought this Fender acoustic/electric guitar about 9 months ago. It has a wonderful rich tone, is easy to play and is beautiful. The grain on the mahogany is dark and beautiful. It lives up to its dreadnought name and can fill a large living room with its sound. The tone is deep, rich and mellow. Strings are separated enough for easy picking. Tuning pegs are of decent quality and once strings are broken in it stays pretty much in tune. Other than putting on some bronze phosphor strings I did not need to set the guitar up. I really haven't played it much with an amplifier so can't comment on the electronics, other than the built in tuner works well. The hardside guitar case is well padded and looks professional. I was a little concerned about buying a guitar over the
It depends on whether you are playing with someone, or you just wanna start to play home in your bedroom. If you play with others, you need an amp that can play loud enough to follow the bass and especially the drums. Marshall make some great tubeamps, but also Vox make some great amps, where this one on 40 watt with effects incl are real good. Sound like a tubeamp, and have a 12ax7 in the frontamp.

# I could not afford an American or European guitar when I was 12, but Sam Ash sported a Japanese stratoslabber, with 1, 2, 3, or 4 pickups. Each extra pick up was another eight dollars! I bought the 2 pick up model for $24 and brought it home. What a square slab. The wood had the aspects of cardboard, it was probably what is called basswood. The pickups were single coil, chrome covered, and no better than a deArmond harp mike. My brother returned it, and bought a better looking tele style Japanese guitar I believe by Kent, with tin foil inserts in the pick ups. It went from Kandy apple red, to natural, to white, and finally to trunk-splatter grey with Seymour Duncan pickups and Grover tuners. I finally sold it in 2009. In 1931, Martin reintroduced the dreadnought with X-bracing and two years later gave it a modified body shape to accommodate a 14-fret neck, and it quickly became their best-selling guitar. The rest of the industry soon followed[citation needed], and today the “dreadnought” size and shape is considered one of the “standard” acoustic guitar shapes, iconic for its use in a wide variety of musical genres. 10. Behringer Ultracoustic ACX450 45-watt ($229.99): Not to leave our acoustic-centric players out of the list entirely, the Behringer Ultracoustic not only looks amazing, but it has a ton of features to keep you inspired and sounding great. Two channels are utilized so while you plug your acoustic into channel one, channel two allows you to input a microphone or another source. The FBQ Feedback Indicators allow you to control the feedback coming out of your amp by monitoring the LEDs on the graphic EQ. Need your own guitar effects? The ACX450 allows for 16 different presets on each channel, including delay and reverb. A great bargain for those looking to take their acoustic playing to the next level!
The RP360 XP lets you combine different effects to craft your preferred sound by choosing from its wide variety of options including 74 effects, 32 amp models and 18 cabinet models. Each setup can be saved into one of its 99 user presets, that allow for incredible flexibility. The interface has a bit of a learning curve, but allows for deep editing.
Most overdrive/distortion pedals can be used in two ways: a pedal can be used as a "boost" with an already overdriven amplifier to drive it further into saturation and "color" the tone, or it can be used with a completely clean amplifier to generate the whole overdrive/distortion effect. With care - and with appropriately chosen pedals - it is possible to "stack" multiple overdrive/distortion pedals together, allowing one pedal to act as a 'boost' for another.[44]
Several notable ranges of similar guitars were produced with different finishes and features; whilst some companies lumped all variants together with a single model name - i.e. a Fender Stratocaster is a Fender Stratocaster, irrespective of it's finish, in many cases Harmony split it's models, giving a different model designation depending on finish, inclusion of a tremolo etc.
There are two main types of amplifier: valve and solid state. Solid state guitar amplifiers tend to be cheaper and lighter, but they don't offer as good a sound as valve amplifiers. Valve ones, on the other hand, have working parts, so they're a little more maintenance heavy. Most serious musicians go for valve amplifiers due to the superior sound and lower wattage requirements.

If you want to test the waters, here are the some of the best free guitar effects software packages. Aside from the limited freeware software, there are Lite or Trial versions of commercial programs which you can get for free, but with limited in features. The good thing though is that even when they lack features, they work and sound just as nice.
Pedaldoc – is a company specialized in the production of kits to convert standard guitar effect pedals into boutique sounding pedal stomp boxes. They carry “do it yourself” kits to modify many topselling Boss pedals, Electro harmonix stompboxes, Vox 847´s wah pedals and more. The only thing needed to perform one of their mods in is about an hour of your time and a soldering iron. Their kits are designed for guitar and bass players who may not have any knowledge of electronics and all the components that need to be substituted are clearly market on a picture of the pcb board of the pedal.
With expiration of the Fender patent on the Stratocaster-style vibrato, various improvements on this type of internal, multi-spring vibrato system are now available. Floyd Rose introduced one of the first improvements on the vibrato system in many years when, in the late 1970s, he experimented with "locking" nuts and bridges that prevent the guitar from losing tuning, even under heavy vibrato bar use.
The Meisterklasse is a high-end harmonica on the modular system, made in Germany, featuring chrome-plated cover plates, an anodised aluminium comb, and extra thick 1.05mm nickel-plated reeds. One other feature that sets the Meisterklasse apart from most other Hohner harmonicas are its full-length cover plates, which extend all the way to the ends of the harmonica's comb rather than sharply angling down before the ends to form an adjoining surface parallel to the reedplates and comb. The only other Hohner harmonica possessing this quality is the curve-framed Golden Melody.[25]
In 1992, two more models were added, the single-cutaway BC-40 and the 5-string B-540. Although widely admired[who?] for their high quality and lovely appointments, they proved to have limited appeal due to their $2000-plus list prices. By 1997, all four of these initial basses were dropped in favor of the B-1, a lower-priced ABG with laminated mahogany sides as part of Martin’s 1 series of guitars. The BM, an even less expensive model in Martin’s now discontinued Road series soon followed; it had laminated mahogany sides with a solid mahogany back. Also around this time electronics became standard on Martin basses. The most recent additions are the BC-15, a single-cutaway version with a mahogany top, the BC-16GTE, also a single-cutaway with solid Genuine mahogany back and sides with a gloss top, and the 00C-16GTAE, which is a slimmer thin-line version of the previously mentioned model. As a special edition, Martin offered the Alternative X Bass with jet black High Pressure Laminate back and sides and a Graffiti-patterned Aluminum finish top. This bass was very similar in build to the other guitars in Martin’s X series. There have been two Limited Edition Martin acoustic bass models. The first, the SWB Sting Signature Model, was released in 1999 and was made with woods certified by the Rainforest Alliance’s SmartWood program[citation needed]. The SWB’s top is made with book matched solid Sitka spruce reclaimed from pulp logs, the back, sides and neck are solid certified cherry, and the fingerboard is certified katalox. Sting’s signature is inlaid between the 18th and 19th frets, and a label inside the body states that a portion of the sale price is donated to the Rainforest Foundation International[citation needed]. The second and more recent Limited Edition is the B-28KV Klaus Voormann Signature model released in 2008 for the German market. It has a Sitka spruce top with Solid East Indian Rosewood back and sides and a black Ebony fingerboard. The headstock features a unique art design by Klaus as a circular inlay making each bass a one-of-a-kind. In addition to these U.S.-made instruments, Martin also markets Sigma ABGs made in Korea. What Fender might lack in heavy, modernized features, it makes up for in affordability, novelty and being some of the best all-around guitars in existence. They would also have to be considered some of the most stylistically versatile guitars, covering all kinds of musical genres and songs. We’ll focus primarily on the Standard (non-American) models, since they’re priced below our$700 cut off. If you want to go with something nicer, target the American series Strats and Teles.
Tremolo is the gentle art of making your signal subtly cut in and out of volume. Think of all those old surf records. Phase and flange are quite similar in essence; phase emulates the sweeping of the frequency band, alternating between cutting the bass and treble frequencies, while flange does a similar thing but with a slightly more extreme sound. Wah is perhaps more well known; the Jim Dunlop Cry Baby wah pedal has been used for decades by players of all genres. Adding a highly distinctive wah-wah sound can elevate a solo into something infinitely more interesting. Or it can add a bit of that classic wakka-wakka sound you hear on classic funk records.
Joe Perry is the American distillation of the good-old Keith Richards/Jimmy Page recipe for sideman/lead guitarist cool. He’s got the look and the licks, and he’s maintained both over the course of three or four decades—despite all odds. Jagger and Richards are the Glimmer Twins, but Perry and Aerosmith singer Steven Tyler went down in history as the Toxic Twins.

I'll start off by saying I am a novice guitar player. I've been playing off and on for 30 years, but more off than on. I've been playing on a hand-me-down Yamaha acoustic that was once a great guitar, but through many years of moving, poor storage and not doing anything other than the occasional set of new strings, that Yamaha just did not play well. One reason I was so off and on is that I could never get a clean sound from the Yamaha. I just thought I was not capable of learning guitar. Then, about a year ago, I tried out a friend's Fender acoustic and, after apologizing in advance for my poor playing ability, found that the same chords I struggled with on the Yamaha sounded crisp and clean on my friend's Fender, and I didn't have to make my fingers bleed
Vox is a musical equipment manufacturer founded in 1947 by Thomas Walter Jennings in Dartford, Kent, England. The company is most famous for making the Vox AC30 guitar amplifier, used by The Beatles, The Rolling Stones, The Kinks, The Yardbirds, Queen, Dire Straits, U2 and Radiohead, the Vox Continental electric organ, and a series of innovative electric guitars and bass guitars. Since 1992, Vox has been owned by the Japanese electronics firm Korg.
The ’62 EG-NT, EG-K and EG-Z were fairly primitive and appear to be leftover from the mid-’50s. The EG-NT had a small rectangular body with the bass side flush with the neck and the treble sticking out a bit to handle the controls. The head was stubby three-and-three with a circle Swan logo sticker and the fingerboard had painted diamond markers. The pickup looks to be the old slotted pickup of the early J-1, but may not be, with volume control. The EG-K was the Teisco version of the Rickenbacker Frying Pan, with a round body and neck with a head wider than the neck. This, too, had the rectangular head with a circle Swan logo. Markers were diamonds, the pickup was the slotted J-1 pickup, with one volume control. The EG-Z had an asymmetrical body with a short width on the bass side and a longer width on the treble side, with diamond markers and the stubby head. This had the old slotted J-1 pickup with volume control.
Our first impression of this guitar was that something must be wrong. Surely this guitar is way more expensive than we thought? We doublechecked and the truth is that it’s just incredible value for money. Both the design and the sound are wonderfully good and we understand why Schecter describe their Schecter Hellraiser guitars as having “raised the bar on sight, sound, quality and affordability”- we totally agree!
One look around our shop and you'll see that we're serious about offering our customers a large selection of instruments, equipment and gear. You'll find both new and used instruments, and our top-notch staff are here to help you choose exactly what fits your needs, preferences and budget. If you're interested in learning new skills and techniques, check out the group workshops we host on a regular basis. We cover a wide range of music topics, so stop by and see what class we're holding next. Can't make it in? Give us a call at 505-889-6300, and we'll be happy to answer all your questions.
Have you ever heard a bridge pickup that made a guitar sound like a giant mosquito attack? If you've run into this problem, The Tone Zone is the solution. The Tone Zone is hot enough to qualify as a high-output pickup, but it has a wider dynamic range - hard picking will produce a lot of power, and softer picking will be much cleaner and quieter. It's got tremendous bass and low-mid response to reinforce the bottom end and make the overall sound bigger. The highest single notes have depth, and chords sound huge. Patented dual-resonance coils reproduce more overtones than you'd expect from such a fat-sounding pickup. It makes a great match with an Air Norton.

The GT-70 was a re-styled two-pickup, single-cutaway recalling the F-55s. The cutaway retained the wide horizontal angle of before, however the upper bass bout received a more graceful treatment, with a slight inward curve as it met the neck at the 16th fret. The controls were the same as before; the elevated pickguard had become a large white affair, the tailpiece was the V-notched Bigsby. Pickups remained our familiar DeArmond humbuckers. Gone were the plastic bridges in favor of metal adjustable finetune variety. Finishes were either burgundy or black. The first prototype serial number was 203803. Around 1,450 of these were made between January of 1966 and October of 1968.
(48 Contiguous U.S. States) Free Free Shipping With Backstage Pass 92118 2-Day Standard Ground {savingIsUpTo=false, MSRP=155.0, listPriceRange=false, isFreeShipping=true, download=false, isPriceDrop=false, salePriceRange=false, YourSaving=0.0, productId=site1prod361014, MSRPRange=false, enablePDPColorOption=false, showBrandNameWithProduct=true, restockStartAmount=null, priceVisibility=1, listPrice=155.0, salePrice=155.0, isOnSale=false, showMSRP=true, restockCount=0}
Playing Small Gigs? If you play small gigs, such as at pubs, clubs etc, small places with capacity of 200 persons or less, you won't need a massively loud amp. A 15-Watt Valve amp will be more than loud enough, such as the Fender Blues Junior or Vox AC-15. You can use louder valve amps, such as a Vox AC30 or Fender Hot Rod DeVille, but in most cases you won't need to set the volume more than halfway up (or less!) Valve amps sound louder than solid state amps, so even though a 15-watt valve amp is loud enough fro gigs, a 15-watt solid state amp will be only recommended for home practice. Good solid state amps include the Orange Crush 20 RT and Blackstar ID:30TVP 30W. Both are loud enough for mid-sized venues and sound superb.
Specs for combos were as follows: Checkmate 10 (6 watts, 6″ speaker, two inputs, striped grillcloth); Checkmate 12 (9 watts, 8″ speaker, three inputs); Checkmate 14 (14 watts, 8″ speaker, three inputs, tremolo); Checkmate 17 (20 watts, 10″ speaker, tremolo, reverb); Checkmate 16 bass amp (20 watts, 10″ speaker, volume, tone); Checkmate 17 (20 watts, 10″ speaker, reverb, tremolo); Checkmate 18 (30 watts, two 10″ speakers, reverb, tremolo); and Checkmate 20 (40 watts, 12″ speaker, reverb, tremolo). Piggyback amps included the Checkmate 25 (50 watts, 15″ speaker, reverb, tremolo); Checkmate 50 (two-channels, 100 watts, two 15″ speakers, reverb, tremolo, “E tuner”); Checkmate 100C (two channels, voice input, 200 watts, two 15″ speakers, reverb, tremolo); and the big hugger-mugger Checkmate Infinite (200 watts, two 15″ speakers, stereo/mono preamp section, reverb, tremolo and a bunch of other switches). The one shown in the catalog actually has a block Teisco logo and carried the Japanese-marketed name – King – in the lower corner.
{ "thumbImageID": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "defaultDisplayName": "Ibanez RG6003FM Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Flat Sapphire Blue", "sku": "sku:site51409670719560", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue-1409670719560.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Flat Transparent Gray", "sku": "sku:site51393862854365", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Transparent-Gray-1393862854365.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000-00-60x60.jpg", "imgAlt": "" } ] }

A phaser uses a filter to sweep the frequency range of the audio input and mixes that with the original audio signal. When the signals are mixed the portions that are out of phase (or out of alignment with each other) cancel out and produce a swirling, shoowsy sound. This effect was very popular in the 1970’s and heard on countless recordings of the era in nearly every musical style.
Read Full Review This electric guitar from Schecter has an awesomely low price for beginners out there with a genre of music in mind is to play rock and lots of heavy metal. The guitar has similarities in design with the Schecter Omen 6 series which is a higher model to the C-1 SGR, but the C-1 SGR also has the humbuckers for its pick-ups controlled by master volume, single tone control and a 3-way toggle to switch between pick-ups to get near on what the higher model can do.
Some early Valco instruments continued to make it into the marketing pipeline – early on, at least. Probably as a sign of the increasing difficulty in getting product, the Spring/Summer 1942 Sears catalog sported a full complement of Supro guitars, essentially the ’41 line, all labeled with the newly-chosen Sears brand name, Silvertone. Shown in the ’42 Sears catalog were the Supro Capitan and Supro Rio, now renamed the Silvertone Crest (carved torch logo) and Silvertone Spanish (no logo), respectively. The Capitan had a standard trapeze tailpiece rather than the Dobro variety, with permanent cord coming out of the top of the lower bout!


The advantage of this specific package is that you’ve got everything you need to get started right away: guitar (duh), amp, strings, tuner, guitar cable, picks, gig bag, strap, and instructional DVD. Those of you who just wanna get a guitar and start, this is your choice. Squier also makes similar package, but I recommend this over the Squier because the parts (electronics) are higher quality, although the Yamaha costs a little bit extra.
Many players today have more than one overdrive/distortion stomp box on their pedal boards and sometimes use both at once. My personal preference is to place the lower gain pedals in front of the higher gain ones, but the opposite is absolutely fine if you prefer the sound of that configuration. Placing overdrive/distortion pedals later in the signal chain can increase noise as the noise of several effects chained together can add up, and any noise produced by other effects going into an overdrive/distortion effect will be boosted along with the guitar signal.
Gibson’s drive to recapture the magic of the original “Patent Applied For” humbucker pickups of the 1950s culminated with the introduction of the Burstbucker line in the early 1990s. In 2002, Gibson followed up this innovative accomplishment with yet another breakthrough in pickup design—the Burstbucker Pro, designed specifically for the new Les Paul Standards. The Burstbucker Pro features an Alnico V magnet (instead of the Alnico II), which offers slightly higher output and allows preamps to be driven a little harder to achieve a more natural break-up. Like all Burstbuckers, the Burstbucker Pro has asymmetrical coils—true to the original PAFs—which supply a more open sound. The Burstbucker Pro Neck is wound slightly less than the original PAFs, while the Burstbucker Pro Bridge is slightly overwound for increased output. The Burstbucker Pro pickups are also wax potted to allow loud volume pressures with minimal feedback.
I’ve written in previous issues of Premier Guitar about how the size and shape of a guitar’s headstock affect its sustain and tone. Clearly, the mass of the tuning machines is a factor in this, as well. Having overseen the building of tens of thousands of custom guitars over the course of my career has given me cause to consider machine-head weight as a fine-tuning tool in and of itself. This kind of mod is more complex than the others I’ve presented here because it is harder to predict, and obviously more costly to dabble in because it involves replacing the existing tuners. Nevertheless, I put it out there for those of you who are willing to go to the limit of sanity in the search for a responsive instrument.
Rolling Stones best electric guitarist list should've been nicknamed the best average guitarist list. I didn't give this guy the time of day because I thought the bucket thing was to cover up how badly he sucks. Turns out it's the opposite. He's just weird. It's too bad the average person doesn't have the capacity to enjoy this type of advanced music.
I like some of the less known models and smaller brands. Deans are very nice, Cort has some very nice models (and cheap crap too..), Fenix LP copies (depending on the model/age) are great and I've got a Morgan strat that seems to just get better every year. Korean Yamahas are pretty nice and so are the ones from Taiwan. Korean/Chinese Epiphones vary quite a bit so try before you buy. Don't care for most Korean Ibanez and ESP/LTD models.
This vintage Teisco Del Rey Japanese guitar was made in the 1960s and has a classic sunburst finish and tulip shaped body. Manufactured in Japan by the Tokyo Electric Instrument and Sound Company (yeah, you got it…TEISCo!), the Del Rey measures 37 3/8 inches x 11 1/4 inches at widest and longest points. The fretboard measures 18 3/8 inches in length from the nut to end. My dad bought this one from some guy at his work, who later supplied him with the original whammy bar and headstock hardware which he found later! The relatively small body size of the Teisco Del Rey was appealing to my wife, who was on the lookout for a smaller-sized guitar she could play. My dad replaced the original tuning pegs with much nicer chrome ones from a 1980’s Gibson SG and we took it home. However, she realized that she didn’t care much for electric guitar, so we decided to clean it up and sell it. Everything was in excellent shape, but it did have some electrical issues. The volume/tone pots were filthy and you could hear a wall of white noise as you turned the knobs. At the time, I didn’t know the marvels of Deoxit and contact cleaners, so I didn’t know how easy it would have been to clear that problem up. One of the pickups or pickup selectors also didn't seem to be working. It played OK without noise or distortion when the volume and tone knobs were set to 10 and the pickup selectors set to "black up, white down", but the sound could still fade in and out sometimes if you bumped the buttons or switches the wrong way. Again, simple issues that I could have cleared up with a soldering iron and contact cleaner. In any case, we meticulously cleaned it and put it up for auction. Despite the minor problems, a bidding war ensued and now this Teisco Del Rey Japanese guitar lives in Australia! Overall, the Teisco is a good playing trashy guitar with loads of funky style. Scroll down for more Japanese Guitars from our collection!

Seriously, Yamaha above ESP?! Japanese made ESP guitars are among the best in the world, no wonder so many people play them. They have great designs and an ESP standard is not to high in price compared to a USA Jackson or custom shop guitar. Ibanez prestige are very nice to (I hate the necks personally) but the build is really good. ESP blows Gibson out of the water by a VERY large margin. Gibson has lawsuits against them for selling "USA" made guitars that were discovered to be imports from cheap labor offshore factories. All ESP and Ibanez prestige guitars are made in Japan and are immaculate in terms of quality and consistency. ESP is more a metal guitar but they have much better tone than any of the others listed, the only one here that might have a sweeter tone is prs but for $8,000 and only a fractionally better tone that is subjective they can keep it. I personally like ESP and Schecter best but Jackson is really good too. Not to knock Ibanez, but their necks are way to thin ...more Most modern effects use solid-state electronics or computer chips. Some effects, particularly older ones such as Leslie speakers and spring reverbs, use mechanical components or vacuum tubes. Effects are often used as stompboxes, which are typically placed on the floor and controlled with footswitches. They are also built into amplifiers, tabletop units designed for DJs and record producers, and rackmounts, and are widely used as software VSTs. By the late 1970s, costs of manufacture in Japan had risen to such an extent that it was difficult to make student-grade guitars over there. It was far less expensive to manufacture instruments in Korea. Numerous factories were built, and existing facilities in Korea were expanded. Samick built a factory capable of producing one million instruments a year. Japanese companies invested heavily in Korea so that they would be able to produce their low-end models in Korea and high-end models under the same brand names in Japan. The early Korean-made instruments were not as good as the Japanese ones, but it did not take nearly as long for Korean quality to improve as it did for the Japanese to go from making crude low-end models to sophisticated instruments suitable for professional use. The Koreas had the benefit of all of the Japanese experience especially in the cases of factories with Japanese ownership or management. James Burton, another famous Twin user, put it best: “If you can plug your guitar into an amp and make it sound good, that’s what it’s all about. The amp I really enjoy playing, especially when I’m traveling, is the Fender ’65 Twin Reverb. It’s got everything you need for live playing and it has great tone. That amp just works for me and it’s real trustworthy. When I travel on the road, I do use a little digital delay and maybe a little chorus, but I just like the sound of the guitar and playing something that I think people will appreciate and understand.” Hi Learmonth! I always recommend Yamaha acoustics for beginners. The FG and FS Series both offer affordable, quality instruments. The question is what size you need to get. Some smaller kids do better on small-bodied guitars like the Yamaha JR2. Of course he would outgrow this by the time he is a teenager, though it would still be a cool guitar to have around. If you feel he can handle a full-size guitar look at something like the FG700S. It's a great starter guitar that will last him a long time, as long as he takes care of it. Good luck and let me know if you have any more questions. At least one other Teisco guitar was available from around this time in the ’50s, probably slightly later on � another mini Les Paul that was the ’50s piece de resistance, the J-5. The J-5 was a single-cutaway solidbody that went beyond the other more derivative LPs. This had a slightly elongated body shape, with less pronounced waist than a traditional Les Paul. The upper bass bout headed toward the neck with a more angular, almost pointed corner rather than the typical rounded shoulder. The cutaway horn was also more angular, heading out at almost a right angle to the neck. It’s impossible to tell from the photograph, but this looks to be a glued-in neck. The fingerboard was bound, and featured the typical large white dots with two small dots at the octave. The headstock was a white-faced asymmetrical affair, with a curved peak extending on the bass side, with a concave dip across the top. Tuners had white rectangular buttons. These would be interesting enough, but the body had a bound flamed maple top � flat, not carved. The pickguard followed the body profile, with an extension down the lower side for the volume and tone controls. On the black pickguard were two black-covered pickups, looking sort of like P-90s. Pickup selection was with a chicken-beak rotary three-way switch. Knobs were white knurled with silver top rings. The bridge was a typical adjustable wooden type. Again, a large tailpiece assembly allowed the strings to pass through the body. This is a very beautiful guitar. The irony with guitars is that an original 1950s Gibson, for example, whilst capable of producing the most amazing sounds, and playing like butter - may not stay in tune, or intonate quite as well as a modern day equivalent. Consequently old guitars have very often been 'upgraded', with original parts lost. But this can seriously down-grade their value. Replacing missing parts with original or period-correct ones can very much improve a guitars collectability, saleability and therefore value. If you’re a player performing live or in a studio, all of this is just the opening pre-credits sequence to your signal then being captured via a microphone, which then sends current through another cable to a mixing board, which then has its own preamplification, equalization and filtering, which either goes to the power amplifiers of a public address system or to some kind of recording device, which then involves…aw, I’m getting tired, and I think we’re getting the point: how can anyone call *any* of this “natural”? Does *any* of this occur in nature? Does any of this sound like we’re carving a flute from driftwood or clapping a couple empty coconut shells together? Among the most common rookie amp buyer mistakes is buying a big amp that's too heavy to gig with, or going the opposite and buying one that's too small. If you're gigging at different places and you don't have a roadie, then consider going with a smaller amp that has DI output so you can go straight to PA with your tone intact. In big venues where big amps are a must, some opt for amp heads because the separated head and speaker cabinet are lighter on their own, although you'll have to move more pieces. The Gruhn Guitars repair shop has been world renowned for decades for its unrivaled expertise, skill, and respectful repair practices. Though our full-time staff of luthiers primarily focuses on repairing and restoring the instruments we make available for sale, beginning in 2016 we are also pleased to offer our repair services to loyal customers as an extended benefit of buying an instrument from Gruhn Guitars. Instruments purchased from Gruhn Guitars will be moved to the front of our repair queue and will be repaired at a discounted labor rate. As a sign of our appreciation for your business, Gruhn Guitars is here to help you for years to come to keep your instrument in the same prime working order as when it was listed for sale at the shop. The dynamic mic’s strengths for close-miking constitute some of its weaknesses in distant-miking, and you’ll more likely want to use a ribbon or condenser mic for this job, if you have one. Distant miking really begins at 10″ to 12″ out, where many condenser and ribbon mics start to bloom. As a rough guide, start 12″ to 18″ from the speaker in order to record an electric guitar sound that is still pretty solid and direct, but captures some sense of air and space and natural room reverberation. You can aim the mic straight at the center of the speaker for a bright and detailed tone, as described in our close-miking techniques above, or move it around in the field, trying different direct and off-axis placements. Any position that achieves a desirable tone is valid, and you don’t have to remain on the same plane as the speaker itself. Moving the mic out adds more space to the sound (while potentially compounding phasing issues – see below). Raising the mic above the speaker and aiming it down slightly to fire toward the upper edge of the cone can let the sound bloom as it reaches the mic. In a room with a carpeted floor, you can position the mic lower to the ground (even below the speaker itself) to cut out some of the reflected sound. Positioned as such, an end-fire mic can be shooting either toward the amp on a plane that hovers above the floor or at an angle toward the speaker, while a side-fire mic can be aimed either way or fire straight at the ceiling with the amp sound washing over its capsule. Even though Ibanez is thought of as a modern guitar brand, we have decades of accumulated knowledge and a history of pushing the boundaries. The AZ series carries with it all of the hallmarks of these tried and tested Ibanez qualities: the smooth oval neck grip, the well balanced asymmetrical body shape, and the neck heel allowing unrivaled playability. It also has an overwhelming amount of sheet music in it. These music sheets allow you to practice what is being taught in the given chapter, which is nice, but going through the books, I felt there was a lot left unexplained. This was probably a result of them trying to simplify things as much as possible, but this actually leaves holes in the padawan guitarist's knowledge. I HAVE A P38-12E I BELIEVE MINE WAS MADE IN SPAIN ALSO. LATER THEY WERE MADE IN MIAMI AND LATER IN CHINA KEEP IT IN GOOD SHAPE I HAVE MANY GUITARS ACOUSTIC AND ELECTRICS. EXCELLENT ACTION AND SOUNDING GUITARS FOR THE PRICE I HAVE GIBSON,EPIPHONE,IBENEZ, THE BEST SOUNDING 12 STRING I EVER OWNED WAS A TAKIMINE. WHICH WAS STOLEN IN LAS VEGAS. EVEN HAVE A 12 STRING ACOUSTIC I MADE. I ADDED A FISHMAN AND MADE IT ELECTRIC I ALSO PUT A TUNEMATIC BRIDGE ON IT. THEY ALL HAD DIFFERENT SOUNDS BUT THE ACTION ON THE PALMER IS THE BEST. I EVEN HAD A VICTORIA VIOLIN BASS WAY BEYOND A HOFNER. JUST BECAUSE YOU DIDN'T PAY BIG BUCKS DOESN'T MEAN ITS NOT BETTER THAN A MARTIN. I PLAYED MY UNCLES MARTIN HE MADE AT THE FACTORY WHEN HE WORKED THERE. AND IT CAME NOWHERE CLOSE TO MY PALMER OR TAKAMINE. PALMER CAME CLOSE TO MY 1960s GIBSON DOVE. DOVE HAD A BETTER SOUND PALMER HAD BETTER ACTION. HOLLYWOOD PHIL. GUITARIST AND SINGER FOR THE GWB BAND. I'M ALSO HEAD SOUND AND LIGHTING TECH FOR THE METAL BAND BLACKFATE. Description: Body: Maple - Flamed - Body Construction: Semi-Hollow (Chambered) - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Block - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Chrome, Diecast, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Amber, Red ### Jazz – Does no-one listen to Eddie Lang’s recordings? Or that master of comping, Freddie Green? To Charlie Christian? MarleyIII gets special credit as the only one naming the marvellous Jim Hall, who really should be up there in one of those ten spots. Like Marley, I really like the work of John Abercrombie, although I can’t put hand on heart and suggest him for the top ten. If you like John A, let me put in a plug for the work of London session-man John Parricelli. (Which reminds me that the very different “Johnny A” is no slouch either!) Talk box: A talk box directs the sound from an electric guitar or synthesizer into the mouth of a performer using a tube, allowing the sound to be shaped into vowels and consonants with movements of the mouth. The modified sound is then picked up by a microphone. In this way the guitarist is able create the effect that the guitar "licks" are "talking". Some famous uses of the talkbox include Bon Jovi's "Livin' on a Prayer", Stevie Wonder's "Black Man", Mötley Crüe's "Kickstart My Heart", Joe Walsh's "Rocky Mountain Way", Alice in Chains's "Man in the box" and Peter Frampton's "Show Me the Way".[66][67] Clapton himself has repeatedly called Guy “the greatest living guitarist.” Hendrix literally knelt at Buddy’s feet in the late Sixties, the better to study his riffs. Guy’s secret? He combines an old-time blues feel with the technical facility of a modern guitar player. He was a youngster at the legendary Chess Records in early Sixties Chicago. Fresh up from Lettsworth, Louisiana, Guy was some 20 years junior to giants like Muddy Waters and Howlin’ Wolf, yet old enough and gifted enough to share the studio with them. Dude everything your saying about Martin is basically true of Taylor. They are the two big brand names. Taylor is to acoustic guitars what Tagheur is to Swiss watches. The low end of an expensive world where thhe best stuff comes from tiny companies who don't advertise much or pay for all he shelf space at a place like guitar center. I'm not saying Taylor's aren't good-that would be ridiculous. I'm just saying your distinction between Taylor and Martin is laughable. They are both well known companies that can charge way more because of their names just like fender and Gibson can with electrics. For the same money think you get better sounding and lasting guitars from Takamine and Breedlove than Taylor and Martin just to name a few. But there are so many smaller luthiers that will make incredible stuff. In ’41, the old Avalon Hawaiian was renamed in the No. 88 Supro Clipper Hawaiian Electric Guitar. This instrument would become a mainstay of the Supro line for many to come, and marked the debut of pearloid plastic coverings for Supro guitars. This was very similar in shape to the Baton. The body was still roughly rectangular, but now with a curved lower edge. The shoulders now had two symmetrical scalloped “cutaways.” The head had a curve with a slight peak; despite the Regal look, these were made by National Dobro. The fingerboard was genuine rosewood with dot inlays. This was covered in “sparkling brown plastic,” i.e. pearloid. The pickup was the new exposed-pole unit with the handrest, contained in a large square metal plate complete with tail slots for fixing the strings, otherwise similar to the plate on the Baton. One volume and one tone control knob sat on either side of the strings. The back was done up in non-slip grey suede. It could be had with a curly, plush-lined, grey shark Servitex case. In April of ’42, the Clipper cost$54.50.
At its core is a combination of solid spruce and maple, which gives it a subtly brighter tone when compared to conventional spruce and mahogany body acoustics. To retain as much of the guitar's acoustic body as possible, Epiphone equipped the Dove Pro with discrete Fishman electronics, with controls that are mounted on the underside of the sound hole.


The Hummingbird Pro is a distinctive square shoulder dreadnought acoustic electric. This lack of cutaway does have some playability disadvantage, but what it does mean is that the tonal quality is absolutely amazing throughout the entire range. Whatever sound you want to get out of the Hummingbird, you can, and the excellent L.R. Baggs Element pickup does a great job of translating that to an electrical signal.
At GuitarBassPro.com. ("GuitarBassPro"), we are committed to protecting the privacy of our customers and users of our web site located at www.GuitarBassPro.com (the "Site") . This privacy policy ("Privacy Policy") gives you details of our privacy practices, including (a) what information we collect about you when you use the Site; (b) how the information will be used or disclosed; and (c) your rights with respect to our collection and use of your data. We may modify these policies from time to time and will provide notice of any major changes by posting such notice on the Site.
What a Beauty! This is a beautiful example of a RARE Vintage Japanese Alvarez 5053 made on 1/11/74. This one is Rare folks with its Old style script logo in mother of pearl inlay check that out...The first thing you can't help but notice on this guitar is how beautiful this guitar looks amazing fit & finish apperance is top shelf..its as good or pretter then others including the Martin ... its not just pretty guitar to look at and admire either it is really well build to play built using some very EXOTIC and beautiful looking tone WOODS as well very high end feel to this one ...as seen in the pics ( new better pics soon to come )It was built using a beautiful grained Sitka spruce top and the gorgeous Back is vivid book matched Brazilian Rosewood as is the sides BR and this examle overall is truly a stunning example, along with the backs center flamed maple section in contrast of the Brazilian Rosewood side sections WoW!, and the beautiful vintage hexagonal cellulloid inlays. modeled after the Martin D41, this guitar is in excellent used vintage collectible condition with only a few finish checks to this guitars glass like finish that one has that warm natural patina only a real 37 year old guitar can earn. Overall very good - excellent vintage condition! It's bound body is masterfully ornately - multi bound, as is the Honduran Mahogany neck & headstock is bound. Action is excellentt and can be easily adjusted up or down to meet your preference by way of an easily adjustable bridge . Truly is a great playing & sounding highly collectible Japanese vintage guitar in its own right. Its Very rare and it has old Alvarez Script Logo! Who cool is that....This is a super rare guitar that tend to go quickly that is getting harder and harder to find! in any condition let alone like this baby it both plays beautifully but it sounds fantastic! Let me know if interested Thanks for looking! Joe.
Washburn Guitars have a history built by skilled luthiers and musicians who share a passion for guitar. There are plenty of new modern and traditional designs, like the Washburn Parallaxe Series which has futuristic and modern voicing, great for metal genres. The Washburn Jazz Series has mellow tones and more traditional construction and playability. View all information
Players perceived a loss of the initial high quality of Fender guitars after the company was taken over by CBS in 1965. As a result, the late-1960s Stratocasters with the large “CBS” headstock and (from the mid 1970s) the 3-bolt necked models (instead of the conventional 4 bolts) with the “Bullet” truss-rod and the MicroTilt adjustment system fell out of fashion. However, many blues-influenced artists of the late 1960s soon adopted the Stratocaster as their main instrument, reviving the guitar’s popularity. Also, so-called ‘pre-CBS’ Stratocasters are, accordingly, quite sought-after and expensive due to the perceived difference in quality even compared with contemporary post-CBS models. In recent times, some Stratocasters manufactured from 1954 to 1958 have sold for more than US\$175,000.
Description: Body: Mahogany - Top Wood: Maple - Quilted - Neck Attachment: Neck-through - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Maple - Frets: 24 - Inlay: None - # of Strings: 6 - Scale Length: 27" (69cm) - Headstock: 7 In-Line, Reverse - Bridge: Floyd Rose Style Locking Tremolo - Cutaway: Double - Hardware: Black, 1x Volume Control, 1x Tone Control, Grover Tuners - Circuit Type: Active - Pickups: EMG 707 - Pickup Configuration: H-H - String Instrument Finish: Tribal Purple, Black flame, Tribal Green, Blue Quilt, Satin Natural, Blue Flame

## I think it's fair to say that we all have a pretty good idea of what reverb is, though there are several ways of emulating it in the studio. Early reverb chambers, plates and springs have now given way to digital solutions, which fall into two main camps: synthetic and convolution. Synthetic reverbs take an algorithmic approach, setting up multiple delays, filters and feedback paths to create a dense reverberation effect similar to what you might hear in a large room. Though these often sound a bit 'larger than life', they've been used on so many hit records that we now tend to accept their sound as being the 'correct' one for pop music production. Most can approximate the sound of rooms, halls, plates and chambers, but in comparison with a real reverberant environment, the early reflections often seem to be too pronounced. The advantage of a synthetic reverb is that the designer can give the user plenty of controls for altering the apparent room size, brightness, decay time and so on.

Many recordings feature multiple guitar tracks playing simultaneously, but sometimes this can clutter up the mix. Another approach is to make each part sound distinctive by using different combinations of guitars, amps and effects. Panning the guitars to various areas of the stereo spectrum will create space for each part, while subtle use of ambient effects can create a sense of depth. EQ can be used to help guitars blend together. Try cutting certain frequencies from one guitar track and boosting those same frequencies in another.
The steel-string beauty is crafted from solid Sitka spruce on the top, which features solid Indian rosewood back and sides, and a slim mahogany neck and rosewood fretboard. You’ll notice some impressive decoration on the BR-160 (as we mention in our full review), including an exclusive Dalmatian-style tortoiseshell pickguard, accurate 14:1 butterbean-style tuners, and an elaborately decorated motherof-pearl headstock.
Humbucker pickups were designed to deal with hum while also offering tonal characteristics beyond those of single-coil models. This design incorporates two single-coils wound together in series, with the polarity of the magnets arranged opposite each other. This design helps to eliminate hum. Hence it’s name. Humbuckers usually have a thicker, louder, more powerful tone when compared to single-coils. While they are very versatile, humbuckers lend themselves to rock, heavy metal, and jazz styles. Famous guitarists who use humbuckers include Slash, Jimmy Page, Joe Pass, and Duane Allman.
Back in the good ol’ days, guitarists had to crank their amplifiers to eleven in order to obtain a nice and creamy distortion. Today, this is no longer the case. Thanks to overdrive pedals, you can basically drive every clean amp into overdrive – at any volume – and choose the amount of gain and shape the tone precisely as desired. The overdriven or crunch sounds are commonly used for rock, to slightly get that “breakup” clean tone or to play blues licks and solos. During the last two decades, guitarists found out that overdrive pedals are also perfect for boosting the crunch channel of their amps into total distortion – a technique often used during guitar solos, to give the sound that extra weight and girth – or, as with the famous Tubescreamer, to tighten up the bass response of the amplifier gain channel. The Boss SD-1 is a very popular choice for overdrive pedals, capable of great sounds. The legendary TS9 by Ibanez is also worth a mention – even considering that it’s available in Mini and Deluxe formats. And while we’re at it, why not give the Harley Benton Ultimate Drive a try? This little screamer can boost your amp into full overdrive at a very competitive price.
The OO-18E was basically the small-bodied OO-18 acoustic with mahogany back and sides, spruce top, and the ring-mounted DeArmond tucked right at the end of the fingerboard. These featured one tone and one volume control, with large two-tone plastic knobs situated down on the lower treble bout. The first prototype was serial number 166839. OO-18Es were produced from 1959 to 1964. Around 1,526 of these were produced.
However, when I’m building a guitar, there’s a myriad of small adjustments I can make to steer the instrument on a desired trajectory. These micro mods are interactive with each other and, depending upon the combination, offer a wide variety of sonic outcomes. But these little mods can also be applied to existing guitars—your guitars—in any number of permutations and to great affect. Let’s take a look at five mods that are easy enough for most players to try.
Welcome to KayBassGuitar.com.  We're a the online Kay Vintage Reissue web site of Rock N Roll Vintage Inc., a Chicago based internationally known vintage guitar dealer.  Kay currently offers the "Street Series" and a "USA Recording Studio" lines.  Kay plans to offer reissues of 12 popular models including the Barney Kessel and the Jazz guitar and bass lines.   The Street Series are authentic reproductions of Classic Kay guitars and basses.   The Recording studio series will offer models with exceptional hand built custom shop quality.  We offer the complete line of Kay Vintage Reissue Basses and Guitars.   These Kay reissue guitars and basses look amazing and play even better.  Currently the Kay K161V Thin Twin and K775V Jazz II guitars and K162V Pro and K5970V Jazz Special basses are available.
I'll second the neck comment, conditionally. My first guitar was a hand-me-down Monterey archtop acoustic that had been my uncle's, and it have a sharp V neck. Out of nostalgia I bought another Monterey on eBay and its cross section feels like a tomato can lying in my hand. After a refret it plays smoother and easier than anything that fat has a right to. The original frets..., not quite.
Some of the smaller amplifiers that I like to talk so much about are not really that small. I mean, the Marshall MS4 Mini Micro Full Stack Battery Amplifier is anything but small, in terms of sound at least. It has a powerful volume output that is hard to ignore for anyone, be it in some bar or in the street or at some gig. The tall tower like shape of the guitar is exceptional in design and yes, while the stack is a little on the big side, the affordable price of it and the quality of tone and volume is definitely worth the little bit of a size problem. Definitely worth your consideration!
A partial PA is harder to define, but it's essentially any PA system that doesn't have the capacity to mic your whole band. More often than not, in these situations, mics end up on the kick drum and snare drum for the reasons outlined above. In this case, it does help to have a little extra juice in your amplifier, but try to keep it tamed, nonetheless.
It is a standard dreadnought with 26 frets. There are no electronics, no cutaway, and no fancy upgrades. It has a book matched sitka spruce top, rosewood fingerboard, adjustable rosewood bridge, cream colored plastic binding, rosewood back and sides, and a black inlaid headstock. The neck is not one piece and is made from presumably African mahogany. It has closed gold tone tuners, black beveled pick guard and some plain black line art for a rosette. This guitar is void of polyurethane and has a lacquer finish, so much the better.
WARTUNG Herzlichen Glückwunsch und vielen Dank dafür, dass Sie sich für ein Produkt von Ibanez entschieden haben. Ibanez legt bei seinen Produkten die höchsten Standards an. Alle Ibanez- Instrumente werden vor der Auslieferung unserer strengen Qualitätskontrolle unterzogen. In dieser Anleitung wollen wir beschreiben, wie Sie das Äußere Ihres Instruments pflegen und Ihre Gitarre in dem Zustand halten, wie sie bei Auslieferung ab Werk war.
###### Vacuum tube or "valve" distortion is achieved by "overdriving" the valves in an amplifier.[40] In layperson's terms, overdriving is pushing the tubes beyond their normal rated maximum. Valve amplifiers—particularly those using class-A triodes—tend to produce asymmetric soft clipping that creates both even and odd harmonics. The increase in even harmonics is considered to create "warm"-sounding overdrive effects.[37][41]

I have a very unique Lyle guitar. It is apparently a 1972 but on the headstock it has the pearl from Gibson and it says Gibson on it as well on the headstock. It has the tail trapeze and the adjustable saddle. I recently had it set up and there is absolutely no fret buzz, it looks like it just came off the wall, stellar condition. My tech was stunned at the body condition and even the frets were like a new guitar? This is the only guitar I have seen that is definately a Lyle but it has Gibson, correctly done on the front of the headstock? I went in to the acoustic section and played a Gibson new hummingbird next to mine and it sounded cheap! I was stunned. I have no idea what this is worth but is like the perfect guitar. No dents, nicks, scratches, just and old guitar that has been babied, no warping anywhere, I think this will play another 30 years easy. If anyone knows about a Lyle with a Gibson logo and Gibson written on the headstock, please let me know
Fractal Audio is a relatively small company that competes directly with the world's biggest amp modeling and effects manufacturers. They built their reputation on the quality of their premium priced guitar processor called AxeFX, but has since expanded into relatively more affordable territory with the AX8 and FX8. Of the two, the FX8 gets our pick because of its incredible balance of quality, complexity and practicality. It is also fits this list better because it is a true multi-effects "only" unit, so there's no amp modeling feature to get hung up on.
For one thing, the signal hasn't really "left the guitar" until the strings stop vibrating completely. In electrical sense, you can only say it's "left the guitar" for a given window of time. It's not unrealistic to think that what's happening ongoing in the guitar can affect the future signal (the pickups don't simply pickup an instantaneous signal then stop abruptly)
##### The late ’36 Supro Amplifier was a spiffed-up version of the amp seen in the ’36 Bronson catalog, with a leatherette-type covering, leather handle, and enclosed, removable back. It now had an 8″ speaker, which spoke through a round grill with four bolts visible from the front. It’s impossible for me to tell from the illustration available to me, but this may still have had the resonator plate grill. The amp had four tubes and a “…special high fidelity circuit” that was “…rich in tone quality, and superfluous [sic!] in power.”

###### The technique is often executed by the little finger of the guitarist which is wrapped around the volume pot of the guitar. When the note is struck the volume is increased from zero by a rolling motion of the little finger. Alternatively, the effect is achieved with a volume pedal. It is sometimes called "violining", because the sound is similar to a bowed violin. Allan Holdsworth pioneered the technique of the pedal swelling along with a delay unit to create a thicker sound that is more associated with the cello. - winner333

Post on February 14, 2013 in the RRF Forum:[12] “When John Hall so graciously let me have the license to build Rickenbacker Acoustics back in ’06, I brought a truck to RIC headquarters and loaded it up with all of the remaining wood for Rickenbacker acoustics, in order to free up some shop and storage space in Santa Ana. There was enough undamaged wood for about 40 guitars, and I’ve reached the end of the line with my RIC acoustic builds. I’ve decided to let my license to build Rickenbacker acoustics expire, effective February 1, 2013. All current orders will be built as agreed.
The following songs have been selected to highlight some of the best electric guitar songs from the 1980s. Each song includes links to tab, and wherever possible links to free audio versions of the song. A guideline for the difficulty of each song has been included. The assumption with these guidelines is beginner guitarists can play the ​basic essential open chords, F major, plus basic power chords. Difficulty assessments do not include the guitar solos.
Some bass amps may have additional controls for onboard effects such as bass chorus or a knob for controlling a multi-effects unit (which might include a suboctave generator, chorus, reverb, fuzz bass etc.). Some 2000s-era amps may have a knob to control digital amp or speaker emulation settings (e.g., emulating the tone of a huge 8x10" speaker stack or a vintage tube amp by famous makers, such as the Ampeg SVT).
This final trick is pretty cool for live use because these effects are very efficient, which means that you can have several tracks of 'racks' without straining your CPU. Go to the Mixer tab at File/Preferences/Project, and check 'Enable Solo on Selected Track'. Solo a track, and now all you need to do to call up a new sound is select a track, and the Solo will 'move' to that track. The change from one sound to another is instantaneous. Now it's time to amaze your audience!
As similar as the two instruments are, bass guitars have enough differences from electric guitars that bassists should definitely look for effects designed specifically for their instrument. By doing that, you’re getting a pedal balanced for the low-frequency dynamics of the bass, and built to help it blend better with the other instruments in the band. Many bass effects have the same purposes as guitar effects described above, including chorus, reverb, delay, phaser and tremolo.
Flanging: This effect involves mixing two copies of the same signal with one of them slightly phase shifted. Historically, it had its origin with studio engineers using reeel-to-reel tape recorders. They would make a copy of a tape and then feed the original and copy together to a recorder, having placed a pencil on the flange of one tape to slightly alter its speed. The slight speed change would not be enough to cause notable delay, but would be enough to cause the two waves to be "out of phase" with each other. The effect is described as a king of "swirling" sound, with notable pitch oscillations if it became more extreme.
Built-in mics aren’t necessarily the budget option as they can be seen on some high-end guitars. They’re extremely helpful when you need volume but not so much where the acoustics of your setting, say in a concert hall, carries sound projection for you. However, the internal mic can raise problems for the performer as they’re prone to producing unwanted feedback. Multi-blend pickup and preamp systems allow you the flexibility to switching out from the mic when it proves to be problematic. However, if you’re going to install one yourself, look for one with a high feedback resistance of exceptional quality.
Merson emerges again as an importer in the late ’50s and early ’60s (as the guitar boom was building), marketing Giannini acoustic guitars made in Brazil and Hagstrom electric guitars made in Sweden. Recall that in the ’50s, the accordion craze had given great impetus to the success of music merchandisers. But by the end of the decade, the collapse of the fad left them holding the squeeze-box, as it were. After some meandering, the Folk Revival picked up at the end of the decade, creating a growing market for acoustic guitars. Hence the Gianninis.
Their selection these days is insane, especially since they target a lot of awesome smaller brands that NOBODY else in the area carries. I'm pretty sure this is the only place in town you can go to play the Reverend line, not to mention damn near every PRS model currently in production. The locally-made boutique stuff they stock is awesome too, and I would have never even known about it had it not been for the shop.
Sound engineers prevent unwanted, unintended distortion and clipping using a number of methods. They may reduce the gain on microphone preamplifiers on the audio console; use attenuation "pads" (a button on audio console channel strips, DI unit and some bass amplifiers; and use electronic audio compressor effects and limiters to prevent sudden volume peaks from vocal mics from causing unwanted distortion.
Frets are the metal strips (usually nickel alloy or stainless steel) embedded along the fingerboard and placed at points that divide the length of string mathematically. The strings' vibrating length is determined when the strings are pressed down behind the frets. Each fret produces a different pitch and each pitch spaced a half-step apart on the 12 tone scale. The ratio of the widths of two consecutive frets is the twelfth root of two ( {\displaystyle {\sqrt[{12}]{2}}} ), whose numeric value is about 1.059463. The twelfth fret divides the string in two exact halves and the 24th fret (if present) divides the string in half yet again. Every twelve frets represents one octave. This arrangement of frets results in equal tempered tuning.
Market sentiment is overwhelmingly positive, with many reviewers describing how the Seagull S6 Classic M-450T exceeds their expectations. Build quality and playability gets the bulk of commendations, along with its clear sound and good acoustic projection. Some even dare to compare the Seagull S6 Classic with super expensive guitars from major brands.

#### Maybe you'd rather check out the legendary "Marshall Sound" in all its glory? If so, flip the switch on the Marshall DSL40C 40W All-Tube 1x12 Guitar Combo Amp. This all-tube powerhouse is great for gigging guitarists, thanks in part to its fantastic projection and its Pentode/Triode switch that allows the performer to drop the power down from 40W to 20W on the fly for even more versatility. When only the best will do, nobody delivers like Marshall.

The HX removes the amp modelling and condenses the rock-solid build, intuitive user interface and neat form-factor of the Helix series into a svelte multi-effects box that will fit on a Pedaltrain JR with room to spare. As on the larger units, editing is highly intuitive. Lightly touching a footswitch opens the edit menu for that patch, with the large rotary and left-right buttons used to switch patch and parameters. More complex functionality like editing signal flow isn’t far away from the user - a couple of clicks through the menu gets you there, and makes creating banks of your own a breeze. In terms of sounds, the same high-quality effects from the flagship units are present and correct, with a number of additional effects that have been developed in the meantime. The drives on offer are excellent, and into a small tube amp we also found the boosts allowed us to drive the amp into saturation, or up the ante for soloing. With a real drive in front, the unit was able to keep up, and the interaction between external drive, HX and amp was close to indistinguishable from stacking two real drive pedals.

Rule 4 – Taking sound-making devices like stompbox pedals out of the equation, there’s an order to the way sounds naturally occur in physical space. For example, guitar amp distortion is made in physical space by turning an amp up enough to cause its circuits to overload, and any echo you might hear happens after the distorted sound hits walls or ceilings and bounces back to your ears. Therefore, logic says that your reverb and/or delay pedals should be last in the signal path, since that is how the sounds they produce actually occur in three-dimensional space.
Lou Reed has been blowing traditional guitar styles to bits since his Velvet Underground days. A fan of Ike Turner's R&B and Ornette Coleman's free jazz, he created epic bad-trip psychedelia on songs like "Sister Ray." "He was rightfully quite proud of his own soloing," wrote fellow New York guitar luminary Robert Quine, "but resigned to the fact that most people weren't ready for it." As a solo artist, Reed kept on ripping up the rulebook: See 1975's Metal Machine Music, a noise opus that took feedback further than Hendrix could have imagined.
Say that three times fast.  Don't even bother yourself about halfround strings.  They aren't that popular for a reason, but it is good to know they exist.  The roundwound strings feature a textured surface created by winding a round wire around the core metal.  Flatwound strings are far more flat along their length because the core is surrounded by a smooth wire, as pictured below:
Jazz guitar playing styles include "comping" with jazz chord voicings (and in some cases walking bass lines) and "blowing" (improvising) over jazz chord progressions with jazz-style phrasing and ornaments. Comping refers to playing chords underneath a song's melody or another musician's solo improvisations. When jazz guitar players improvise, they may use the scales, modes, and arpeggios associated with the chords in a tune's chord progression and elements of the tune's melody.
Although most of us who participated in this article have years of experience with guitar amps, none of us was particularly familiar with all the latest beginner models. There are few reliable professional reviews of beginner amps, but I sorted through what we found, searched through music stores and websites, and sampled numerous models at the recent National Association of Music Merchants (NAMM) show in Los Angeles. This experience gave me a good idea of what’s available now.
Mike Hedges also uses this idea a great deal, and explains how it really comes into its own at the mix. "You've got two or three tracks of guitar: one clean, one medium — say, half-driven — and then one really driven. As the song progresses, you might use the nice clean track during the verse, as you're coming to the bridge you fade in the heavier guitar sound, then back it off a bit, into the chorus with everything full on, then back to the next verse and drop it all out. It's all done on one guitar track, so it doesn't sound like you've done 10 guitar overdubs. It has a different quality, it sounds like a live performance, but you've got real dynamics in the sounds. It's a very effective technique."
For his work on Supernatural, Glenn Kolotkin turned to elaborate multi-miking as a way of managing Carlos Santana's complicated setup. "I used multiple microphones on Carlos' guitars: Electrovoice RE20s close, Neumann U47s further away, an SM56, U87s. He was playing through an assortment of amplifiers at the same time, and by using multiple microphones I was able to get just the right blend."
At the end of the day your personal preferences will prevail. The brands listed above are going to include just about every style of guitar you can wish for. This goes both for aesthetics and tone. I can safely say that sticking to my personal picks won’t leave you disappointed. Hopefully you have found this guide helpful. Do you like my choices? If so, leave a comment bellow and give me your two cents.


I have 12 years whit my SL3 Jackson and 12 years whit my RG7420, so far I have replaced both POTs on the jackson, the frets are really worn out and FR chrome is peeling.. great guitar crappy components. oh, I havent had to replace anything on the Ibanez yet other than the stock pickups for something better. both are made in Japan =). So dont tell people that Ibanez sucks before actually owning one...

I have to say I'm really impressed with the Obsidian HSS wiring harness, The build quality is top notch, and the simplicity to install really delivered.It only took a few minutes to connect and be up and running. I love to customise my guitars and love to play around, so having the ability to swap out pickups without a messy soldering iron is fantastic, and the wiring is super clean giving a professional finish. I'll be intending to use the obsidian wiring harness in future project guitars -I highly recommend- Guitar sounds great ( oh did I mention the extra guitars picks too. nice touch)" - Ricci Custom HSS Strat® Wiring

For larger venues such as stadiums and outdoor music festivals, or for music genres that use bass instruments with an extended lower range and high stage volumes (e.g., heavy metal music, grunge, hardcore punk), bass players often use a more powerful amplifier (300 to 2000 watts or more) and one or more separate speaker cabinets (often called "cabs") in various combinations. Using a separate amplifier cabinet and speaker cabinets is colloquially referred to as a "bass stack". An example of the powerful, loud bass amplifier systems used in grunge is Alice in Chains bassist Mike Inez's setup. He uses four Ampeg SVT-2PRO amplifier heads, two of them plugged into four 1x18" subwoofer cabinets for the low register, and the other two plugged into two 8x10" cabinets.[7]
Moreover, it can hand a wide range of musical styles and techniques. In most cases they're more popular with classic rock and blues fans, perhaps the Stevie Ray Vaughan or Eric Clapton enthusiast. However, there have been players over the years who have used Stratocasters in much heavier styles of music. Billy Corgan and Jim Root are just a couple that come to mind.
Until the 1950s, the acoustic, nylon-stringed classical guitar was the only type of guitar favored by classical, or art music composers. In the 1950s a few contemporary classical composers began to use the electric guitar in their compositions. Examples of such works include Luciano Berio's Nones (1954) Karlheinz Stockhausen's Gruppen (1955–57); Donald Erb's String Trio (1966), Morton Feldman's The Possibility of a New Work for Electric Guitar (1966); George Crumb's Songs, Drones, and Refrains of Death (1968); Hans Werner Henze's Versuch über Schweine (1968); Francis Thorne's Sonar Plexus (1968) and Liebesrock (1968–69), Michael Tippett's The Knot Garden (1965–70); Leonard Bernstein's MASS (1971) and Slava! (1977); Louis Andriessen's De Staat (1972–76); Helmut Lachenmann's Fassade, für grosses Orchester (1973, rev. 1987), Valery Gavrilin Anyuta (1982), Steve Reich's Electric Counterpoint (1987), Arvo Pärt's Miserere (1989/92), György Kurtág's Grabstein für Stephan (1989), and countless works composed for the quintet of Ástor Piazzolla. Alfred Schnittke also used electric guitar in several works, like the "Requiem", "Concerto Grosso N°2" and "Symphony N°1".