For our purposes, I’ll break pedals down into four overarching categories: 1) Boost, Compression, Distortion, and Fuzz; 2) Modulation; 3) Echo and Delay; and 4) Filtering and EQ-Based effects, and this series will focus on individual types that come within each of those larger categories (for example, Modulation includes many quite different effects, such as chorus, vibrato, phasing, and so on). This is not to say that some manufacturers or other writers couldn’t categorize things differently, and certainly a few examples below could be safely lifted out of the heading I have stuck them in and accurately described by another category. It doesn’t matter all that much. These headings are mainly a means of breaking down the sonic results of the enormously varied range of pedals that exists out there, and taking a brief look at what makes them tick.
This page is a work in progress and as new information is revealed it will be added to the list. But I can't do this alone, folks. See a guitar not listed? Tell me! Listed below are the major manufacturers, known badges and suspected badges to the best of my knowledge in written and list form to make it easy to find out WHO MADE YOUR GUITAR! In some cases I won't know because the badge you have may be extremely rare and virtually unknown to even seasoned collectors.
Frets on finished fingerboards may be tough to measure accurately when the finish has appreciable thickness (think Rickenbackers, 70s Fenders) as these manufacturers spray the finish over the fretted neck.  I have measured a finish chip from a 70s Fender maple neck refret that was .010” thick – lowering the fret height by .010” (25% in the case of the stock medium wire at the time) from just finish alone.  I recently refretted a 2008 Fender Eric Johnson Strat where the fret height prior to any work was .040”, yet the crown of the fret removed from the fingerboard was .045”.  I personally do not like this feel and so often I will suggest refretting over a finished fingerboard when working with them rather than under the finish.

Immediately you can see that this unit is on the larger side, measuring 25 inches (63.5 cm) across, and weighing about 11 lbs (5 kg). If you’re concerned about portability, we noticed one of the most purchased items together with the HD500X is this case, which comes highly recommended and will keep your multi-effects pedal safe during transit and storage. The Line 6 POD HD500X itself has superb build quality. It has a very nice metal chassis, and heavy duty construction. The build quality probably doesn't get much better than this in a multi-fx unit (we say it is a step above the Zoom G3X). We won’t spend a ton of time talking about the inputs/outputs and controls available on the Line 6 POD HD500X, since you can very easily discern that from photos of it. We will say that of all the multi-effects pedals on our top 5 list, this is the most robust. The inputs/outputs cover above and beyond what you probably need. You’ve got your basic inputs and outputs, USB 2.0 so you can use it as a USB interface and for DAW integration, MIDI in/out/thru, FX send and return, AUX input, balanced XLR outputs, integrated mic preamp, and more. In short, however you want to integrate the HD500X into your bedroom, music studio, or live setup, there’s a very good chance you’re covered.
vintage harmony h75 hollow body guitar ser 519 1966, vintage 1950s vega odell model e130 hollow body electric guitar in case, vintage 1960s harmony h56 rocket hollowbody w hsc, vintage baldwin electric hollow body 12 string arch top awesome sound and player, vintage egmond hollowbody electric guitar gold foil pu make offer, vintage circa 1956 gibson es175 d hollowbody electric guitar white refin p90, vintage 1966 conqueror 335 shaped hollowbody sunburst arch top hh bigsby style, vintage vantage vsh455 hollowbody electric guitar with original case no reserve, vintage rare galanti hollowbody electric guitar super funky 1960s, vintage 1968 gibson usa johnny smith hollowbody guitar rare doublepickupwohsc, vintage 60s japan mij teisco del rey ep10t thinline hollowbody sharkfin guitar, 1966 harmony h74 hollowbody electric guitar original case clean vintage, vintage kapa series 500 hollowbody electric guitar amp; case usa, vintage bruno conqueror made in japan mij electric guitar hollow body , 1980 ibanez artist as200 vintage hollow body electric guitar, 1967 gibson usa es33512 vintage semihollowbody 12string electric guitar, vintage 1970 gibson es175d hollow body electric guitar, vintage hollowbody electric guitar harmony kay silvertone must see no reserve, 1964 gretsch tennessean 6119 vintage hollowbody electric guitar w bigsby , vintage experienced 1967 harmony h72 hollow body guitar, vintage circa 1967 framus atlantic 5113 semihollow body original cherry red , vintage original circa 1969 aria es335 copy semihollow body electric guitar, vintage 1966 baldwin burns vibraslim semihollow body guitar clean no reserve, awesome vintage hagstrom viking super rare 12 string hollow body w low action, beautiful vintage harmony h75 hollowbody electric guitar, vintage 1960s harmony silvertone model 1429l hollowbody electric guitar w ossc, vintage 1967 gretsch rally hollow body electric guitar bamboo yellow orig case, vintage 1961 epiphone broadway arch top hollow body electric guitar natural , vtg conrad brown sunburst electric guitar es 335 type hollow body wcase j0330, vintage 1970s ibanez model 2358 semihollowbody electric guitar al caiola copy, vintage 1988 gibson es335 jc showcase edition electric hollowbody guitar w case, rare vintage 60s egmond electric hollow body guitar from holland cool, vintage circa 1969 harmony rebel semihollowbody electric guitar sunburst ossc, vintage 1960s vox super lynx hollowbody electric guitar sounds amazing, vintage usa 1972 harmony rebel h81 hollowbody electric guitar near mint wtags, vintage 1954 gretsch 6186 clipper hollywood hollow body w case rare nice, vintage circa 1969 greco hollowbody double pickup electric guitar brown w ssc, vintage circa 1966 made in japan semihollow body electric guitar sunbust clean, 1967 vintage guitar aria diamond 1202t hollow body no case free shipping used, vintage 1966 harmony h59 rocket 3 hollow body red burst finish rare nice
Looper pedal: A looper pedal or "phrase looper" allows a performer to record and later replay a phrase, riff or passage from a song. Loops can be created on the spot during a performance (live looping) or they can be pre-recorded. By using a looper pedal, a singer-guitarist in a one person band can play the backing chords (or riffs) to a song, loop them with the pedal, and then sing and do a guitar solo over the chords. Some units allow a performer to layer multiple loops, enabling the performer to create the effect of a full band.[87] The first loop effects were created with reel-to-reel tape using a tape loop. High-end boutique tape loop effects are still used by some studio producers who want a vintage sound. Digital loop effects recreate this effect using an electronic memory.[88]
No, could it be!? Finally we see a brand that does not come from England nor the US, but from Germany. ENGL specializes in tube amps for high-gain and heavy-metal. Its most famous users are Ritchie Blackmore and Steve Morse (Deep Purple), Alexi Laiho (Children of Bodom) and Chris Broderick (Megadeth). Both past and present Deep Purple members even have their own signature model. And there's also the standard Powerball, Fireball, Classic, and Invader series.

Launch price: $1,949 / £1,639 | Body: Alder | Neck: Maple | Scale: 25.5" | Fingerboard: Rosewood | Frets: 21 | Pickups: 3x Pure Vintage '65 Gray-Bottom Single-Coil Strat | Controls: Volume, neck tone, bridge/middle tone | Hardware: Pure Vintage 6-saddle Synchronized vibrato, Pure Vintage Single Line 'Fender Deluxe' tuners | Left-handed: Yes | Finish: Olympic White, 3-Color Sunburst, Candy Apple Red
In low-end instruments laminated or plywood soundboards are often used. Although these materials often impart great strength and stability to the instrument, via layers of perpendicular grains, they do not vibrate the same way that natural wood does, generally producing an inferior tone with less amplification. Instruments with laminated or plywood soundboards should be avoided if possible.
There’s another wrinkle: vintage-style pickup magnets can weaken over time, resulting in a softer, smoother tone. Some pickups are designed to mimic this ageing process. Say you were looking for a vintage P.A.F.-style humbucker: You could choose between one of our models that that sounds like a pickup straight off the late-’50s production line (the Seth Lover humbucker), and another that mimics a similar pickup as it would sound and look today after decades of wear and tear (the Antiquity humbucker).
Another technology that is used in Delay units is a feedback circuit, consisting of a tracking oscillator circuit to hold a note of the last interval, and after amplifying the signal, send it back to the input side of the delay. While it was first associated with Boss DF-2 Super Feedbacker & Distortion, currently, the signal feedback circuit is employed by Delay pedals, and if used under "hold" mode (As in Boss DD-3) it will provide a sustain effect instead of a simply delay effect.
Not nearly as popular as single-coils and humbuckers, piezo pickups can be found on electric guitars as well. These crystalline sensors are usually embedded in the saddle of an electric guitar. Piezo sensors operate on mechanical vibration as opposed to magnets to convert sound from vibrating strings into an electric current. Piezo pickups can be used to trigger synthesizer or digital sounds much like an electronic keyboard. Most often, piezo pickups on an electric guitar are used to simulate an acoustic guitar tone. Piezo-equipped guitars often also include magnetic pickups to expand their tonal versatility.
Further simplifications occur for the regular tunings that are repetitive, that is, which repeat their strings. For example, the E-G♯-c-e-g♯-c' M3 tuning repeats its octave after every two strings. Such repetition further simplifies the learning of chords and improvisation;[71] This repetition results in two copies of the three open-strings' notes, each in a different octave. Similarly, the B-F-B-F-B-F augmented-fourths tuning repeats itself after one string.[73]
The FR6UC's matt black flat finish and lack of bling lends the instrument a mean, no-nonsense aesthetic that would be a perfect fit for the modern metalcore player. There's an ebony fingerboard and its neck is a five-piece affair, with two thin strips of 0.5mm walnut between three sections of maple. The FR6UC's suitably rock-looking distressed pickup covers house a pair of Bare Knuckle Aftermath humbuckers with "accelerated bass response for exceptionally fast tracking of high-speed staccato riffing with crushing midrange and precise high-end articulation". The 14.7k-ohm bridge unit comprises a trio of ceramic magnets, while the neck is Alnico V with a DC resistance of 11.5k ohms. This instrument is built cleanly with excellent fretwork, as you would expect from a Japanese guitar at this price point, although it has to be noted that - considering its relatively compact proportions - it's a little on the weighty side, weighing in at 3.8kg (8.4lbs). The FR6UC's Bare Knuckle Aftermaths in full humbucking mode are perfect for a gamut of king-size-yet- articulate heavy rock tones, from Foo Fighters and Queens Of The Stone Age right through to Deftones and Slipknot. That said, the Aftermaths are by no means all about metallic high gain; back off the volume and switch to position two or four to get one of the inner coils in isolation and you'll enjoy pleasantly springy Strat-style tones. It may be none-more-black in appearance, but there's a broad range of hues on the FR6UC's sonic palette.

That’s not to say you need a specific guitar for each style — if you want a larger range of tones for different genres, a solid-body guitar is a good bet. There are also plenty of guitars on the market that include both humbucker and single coil pickups, thus allowing for even more sound options. Still seem too complex for you? If you look to the pros you’ll see that Gibson’s Les Paul and Fender’s Stratocaster have been used over and over again by recording artists. It’s not a coincidence: they’re capable of a lot of versatility. Yes, they differ from each other in tone, but with the right additional gear, you can replicate a ton of sounds.
A modern popular rock artist known for use of the Super Beatle is Tom Petty and the Heartbreakers, although in the April 2008 issue of Premier Guitar, lead guitarist Mike Campbell revealed that the Super Beatle backline was, on their thirtieth anniversary tour at least, primarily used only as a stage prop, though Petty used his "on a couple of songs." In the group's early days, the Vox equipment was chosen because it was relatively inexpensive in 1976, yet had a handsome appearance. A photograph included in the article showed Campbell's guitar sound was coming from other amplifiers hidden behind the large Super Beatles, which Campbell stated were "a tweed Fender Deluxe and a blackface Fender Princeton together behind the Super Beatle, and an isolated Vox AC30 that I have backstage in a box."
Paramount: Around 1930 Martin made about 36 guitars with strange construction. A style 2 size body mounted into a larger rim and back of rosewood, small round soundholes around a "lip" that joins the outer rims to the inner rims, no soundhole in the top, 14 frets clear, dot fingerboard inlays to the 15th fret, rounded peak peghead with standard Paramount banjo peghead inlay, banjo-style tuners, four or six strings.
A musician's pedalboard can be a cluttered place, with lots of stompboxes all competing for room, not to mention creating a virtual spaghetti of patch cables. Wouldn't it be nice to swap out some of those pedals in exchange for a single unit? Of course it would, and that's why multi effects pedals exist. With one of these babies at your feet, you'll have multiple pedals in one. That does more than just clean up the visual look of your effects loop - it also makes your pedals easier to manage and use, and if you're a beginner, you'll appreciate how much simpler it is to put together your board with the most common effects all gathered in one unit.
There are two different Vox Shadows (the Shadow made between 1060 and 1965 and the White Shadow made in the early to mid 80's). The Shadow is a double cutaway solid body with six-on-a-side tuner headstock,with 3 single coil pickups, the hardware is chrome, it has a white pickguard, tremelo bar with a retangular cover over the bridge with the VOX logo on it. It also has one volume and two tone controls and a pick-up selector knob on the lower cutaway bout. This is based on information from the 7th Ed. of the Bluebook of electric Guitars....Hope it helps...John
It is a popular technique in which the player's thumb or index finger on the picking hand slightly catches the string after it is picked, canceling the fundamental of the string, and letting one of the overtones dominate. It is used by popular guitarists such as Eddie Van Halen, Steve Vai and Joe Satriani who utilize the tremolo arm and high gain amps together with the pinch harmonic to produce horse-like wails from the instrument. - winner333
There is clearly a great deal that the guitarist can do for the sound by changing guitars, strings and amps, but from the perspective of the recording engineer it's also important to think about how the guitar cab is interacting with the room it's in. For example, Roy Thomas Baker mentions that he sometimes sets up the same guitar cab in different rooms because of the effect on the sound. Even if you're restricted to one room, a number of producers suggest trying out different positions of the amp in the room. Tony Visconti: "It's not so much that you're miking a guitar — you're miking a guitar in a room. I had a cellist in here recently, and I moved her until I got a good sound. Once I put her in one particular corner, her cello just sang — the room just filled up with the low end, and the sound exploded! A person who hasn't had years of experience might not have thought of doing that, but I could tell there was something lacking when she was in the centre of the room. That's mic technique. It's not so much the instrument; the room is very much part of the sound."
In 1966, Vox introduced the problematic V251 GuitarOrgan, a Phantom VI guitar with internal organ electronics. John Lennon was given one in a bid to secure an endorsement, although this never happened.[citation needed] According to Up-Tight: the Velvet Underground Story, Brian Jones of the Rolling Stones also tried one; when asked by the Velvets if it "worked", his answer was negative.[citation needed]
According to the Amazon page for this guitar, the item weight is 18 lbs, but that’s likely due to the inclusion of the case. There are no other reviews of this instrument, but just keep in mind that with a spruce top guitar, you’re going to have higher, clearer treble sounds than with a cedar top. Also, compared to higher-priced guitars from the Ramirez workshop, this particular model—considered an “entry” model—is a bit more affordable, which was Amalia Ramirez’s aim in reviving the 3N series.
The Ibanez pickup sound is great and solidly diverse throughout the 5-options, providing lots of versatility for a variety of different music styles.The tuning is nice and extremely stable, and you can even dive-bomb on the whammy without throwing it out of whack. The frets are perfect, and the action is almost perfect, with that quality feel to it.

Whether you play classical folk or modern metal, it doesn't matter. There is an amplifier to suit the needs of your music and your bandmates. All you need to do is take a moment to determine which features you need and you'll have plenty of amazing options to choose from. If you're just having a browse or aren't entirely sure where to begin your search for an amplifier, you'll almost certainly be best served by checking out our top sellers. An option such as the Fender '68 Custom Deluxe Reverb 22W 1x12 Tube Guitar Combo Amp with Celestion G12V-70 Speaker, for example, might be just what Doctor Rock ordered. This amp is small, yet powerful, and absolutely loaded with tone. Both of its channels boast reverb and tremolo, and, best of all, the "custom" channel features a modified Bassman tone stack, allowing for even more flexibility when you plug in and play.
In terms of the electronics, Yamaha went with a System 66 piezoelectric platform. The preamp packs a standard three-band EQ couple with a built-in tuner and a flexible mid-range control. Needless to say, it gives you more than enough room to dial in a decent tone. Quality-wise, this might be the best acoustic electric you can get in this price range, period.

I've got a vox white shadow too though its a crimson/red colour with 2 chrome plated humbuckers, it has one volume pot, two tone pots, 1 toggle switch aswell as 2 further switches to change between pick-ups. It has stamped on the back neck plate "made in japan" I can't seem to locate the serial number though. Would love to know more about this guitar.
At some point, I'm guessing near the end of the Buegeleisen & Jacobson ownership-era, a few hollow and semi-hollow body guitars were sold. They shared some of the hardware and necks of the 7-800 series guitars but had symmetrical bodies and no tilted pickup. The bodies resembled the Gibson ES-335 and ES-175T. They appeared to be equiped with humbucking pickups. I'm not following those, but I'd love to have that 175T copy. See the very end of the Varieties page for some photos.
Let me begin by saying this guitar is really good right out of the box. It has a booming sound, and really fills a room even when not plugged in. However, to make it really shine, you should perform a basic setup. I replaced the saddle and pins with bone and sanded the bone saddle down to lower the action. The nut is good from the factory. I also oiled the rosewood fretboard and added Martin phosphor bronze medium strings. After doing this work, the guitar sounds every bit as good as my 90’s Martin DR which is stellar. At this price range, I didn’t expect much, but what I received was a very pleasant surprise. Don’t hesitate to buy this package!
Basswood comes from Linden trees, and it is soft and easy to work with. A side effect of being soft is that it also dents easy. Because it doesn’t have much of a grain or color, it’s most commonly used on instruments that have an opaque paint-job, though this isn’t always the case (as in the photo above). Basswood has a warm, balanced sound with great mid range and good sustain.
Bass guitar tabs are basically meant to be plucked with fingers. One should try to pluck with all the four figures and if not possible then first two. One should also try to understand the rhythm of the drum and the tempo of the song, while reading the bass beginner guitar tabs mentioned below. The technique used to play these tabs is that the alphabets mentioned to the left of each string, is the string name, and have to be used. And the number represents the fret number. Try jamm'n with the bass guitar and the bass guitar tabs for beginners, that are mentioned below.
Hi Jeff. I just wanted to point a couple of things that IMHO are not 100% accurate. Most probably its just to make things not too complicated, but I think is important to notice them. First, resistance is not frecuency dependant, and therefore it doesn´t have any effect on high frecuency content. However, Impedance does, and impedance is the resistance on the AC world (and a guitar signal is an AC signal). Therefore, the reason both long cables and pickups loose high frecuencies as they get longer is because the capacitance in them increases, and capacitors have a certain impedance (once again, resistance in the AC world). So you may actually be true, but its because of impedance created by the capacitance and inductance present on the pickup. Will continue..

Marshall are king when it comes to stacks and rock where fender leads with combos. Marshall offer a wall of sound with punchy lows, strong mids and aggressive highs. But it's not all shrill highs,dial back the trebble a little and you can also get really nice cleans and some real grunt as the crunch sets in. The classic Marshall sound is so coveted that there the market is saturated with imitators. - Antmax


X-Series: Back and sides constructed from compressed wood fibers (high-pressure laminate or “HPL“) and solid Sitka spruce or HPL top. Due to this construction these guitars are more environmentally-friendly.[citation needed] Models include: DX1, DX1-R, DXM, DCX1E, DCX1R3, 000CXE Black, and 000X1. Some earlier models used ‘Ebonite’ (black Micarta) fretboards, later models use koa or striped ebony. Necks on all models are constructed from Stratabond, a laminated wood product used for decades in gun stocks and hunting bows. Some of the more recent models are made in Mexico.

The best is a personal idea. Clapton & VanHalen can make a Walmart Special sound good. Paul Reed Smith made a guitar out of plywood purchased at HomeDepot and it didn't sound bad. IMHO Gibsons are too heavy, Fenders are like broom handles, Suhrs are Fender copies, BC Richs sound like muddy water, and Jacksons are just plain ugly. But if you like 'em, that's fine with the rest of us. I do laugh at people who shell out major $$$ for an axe and they still suck at playing. Dream on.

Tremolo is the gentle art of making your signal subtly cut in and out of volume. Think of all those old surf records. Phase and flange are quite similar in essence; phase emulates the sweeping of the frequency band, alternating between cutting the bass and treble frequencies, while flange does a similar thing but with a slightly more extreme sound. Wah is perhaps more well known; the Jim Dunlop Cry Baby wah pedal has been used for decades by players of all genres. Adding a highly distinctive wah-wah sound can elevate a solo into something infinitely more interesting. Or it can add a bit of that classic wakka-wakka sound you hear on classic funk records.
Vibrato: Vibrato effects produce slight, rapid variations in pitch, mimicking the fractional semitone variations produced naturally by opera singers and violinists when they are prolonging a single note. Vibrato effects often allow the performer to control the rate of the variation as well as the difference in pitch (e.g. "depth"). A vibrato with an extreme "depth" setting (e.g., half a semitone or more) will produce a dramatic, ululating sound. In transistorized effects, vibrato is produced by mixing an instrument's audio signal with a carrier wave in such a way that generates frequency variations in the sound wave.[81] Guitarists often use the terms "vibrato" and "tremolo" misleadingly. A so-called "vibrato unit" in a guitar amplifier actually produces tremolo, while a "tremolo arm" or "whammy bar" on a guitar produces vibrato.[83][84]

Thanks for posting the cool video. I have a Decca like that one. Its pickups migrated to my #1 guitar, which is a relative from roughly the same era (early 1970’s), a Daimaru (sunburst, jazzmaster / jaguar copy surf guitar body, tremolo, etc.). The Decca now has one Daimaru pickup (I wrecked the other one when I was a teenager — thinking I was going to ‘improve’ it), but otherwise, my Decca looks basically identical to yours — except for it has the original tuners, and I angled the bridge in the 1990’s. The neat sound you can get from one of these particular Deccas is the placement of the bridge pickup, it’s a bit further from the bridge than a lot of other electrics, which gives it a neat, plunky sound to it — as is apparent from your video.
But alongside Davy Graham and Jim Hall, the other musician I really wanted to remind you about was Martin Taylor. Astonishing technique – enough to make the shredders weep with envy, coupled with an exquisite feel for melodic line. Martin is one of the few guys (or gals) whose playing brings tears to my eyes regularly. When one of his albums gets into my CD player it stays there for weeks. In many ways, a natural successor to Django Reinhardt, truly a master of music as well as the guitar art and DR’s principal competitor for a top ten place in my list.

{ "name": "Walnut", "skuUrl": "/Epiphone/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Walnut-1500000014893.gc", "status": "instock", "statusText": "In stock", "skuItemType": "New", "inventoryText": "In Stock & Ready To Ship", "inventoryKey": "in_stock", "availableDate": "11-20-2018", "price": 149.00, "isOnSale": false, "msrp": 248.00, "salePrice": 149.00, "easyPayOptions":"0,0,8200002,12 Months Promotional Financing,10/31/2018,Special 12-month financing + $7 back in rewards Valid through,149.0,true,/pages/Gear-Card-Rewards.gc", "formatedIntegerValue": "149", "decimalValue": "00", "listPrice": 149.00, "isPriceDrop": false, "priceDropPrice": "", "savingsAmount": 99, "discountPercentage": 40, "promos":["coverageEligible","freeShipping","international"], "warranty": true, "sku": "site51500000014893", "shipToStore": true, "displaySku": "J40301000005000", "displayId": "1500000014893   POS #: 112318365", "serialized": false, "stickerDesc":"Top Seller", "stickerDisplayText":"Top Seller", "shipsFree":true, "condition": "New", "commerceType": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/J40301000005000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"false", "invMsgPreOrder":"false", "invMsgPromiseDate":"", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Walnut/J40301000005000-00-140x140.jpg", "styleImgAlt": "Les Paul Special Vintage Edition Electric Guitar Walnut", "freeGiftWarning":false, "freeGiftWarningTips":"", "kitCarouselItems": [], "availableInStoreOnly": false, "isShipsInternational": true, "checksum":"93895071200", "restrictionType":"", "restrictionError":"" ,"storeInfo":[ { "storeName" : "La Mesa", "storeStatus": "Ship to Store" } , { "storeName" : "San Ysidro", "storeStatus": "Ship to Store" } , { "storeName" : "San Marcos", "storeStatus": "Ship to Store" } ] }
The best guitar I've found so far is my Westone Thunder 1a, from Matsumoku factory in Japan, 1982, which I got 2nd hand for £255. This has phase switching. coil split and an integrated preamp and EQ. It's got a 3 piece laminate neck with the centre strip at a right angle to the outer strips. It's got a brass bridge, nut, and knobs. It's 34 years old and the neck is as straight as an arrow. This guitar comes closest to having everything I could want in a guitar.
Look for lyrics or chord changes. Many songs have guitar parts made up solely (or mostly) of chords. This is especially true for rhythm guitar parts. In this case, the tab may forgo typical tab notation in favor of a simplified list of chord changes. These chords are almost always written in standard chord notation (Amin = A minor, E7 = E dominant 7, etc.) Simply play the chords in the order that they're listed - if it's not noted otherwise, try playing one chord per measure, but if the changes don't sound right, listen to the song for the strumming pattern.
Many players today have more than one overdrive/distortion stomp box on their pedal boards and sometimes use both at once. My personal preference is to place the lower gain pedals in front of the higher gain ones, but the opposite is absolutely fine if you prefer the sound of that configuration. Placing overdrive/distortion pedals later in the signal chain can increase noise as the noise of several effects chained together can add up, and any noise produced by other effects going into an overdrive/distortion effect will be boosted along with the guitar signal.
The following effects are a step up from your basic overdrive, distortion and fuzz, with more specialized sounds. In this category, you’ll find pedals that include effects such as time delays or frequency modifications – things that go beyond changing the shape of a sound by also changing the pitch, rhythm or both. Others are simpler, but still offer enough tone-altering potential to set them apart from the basic pedals.
These samples are released under the GNU GPL license. The source code being the sf2 files (of which contain the audio samples and settings). The samples and settings can be accessed within Viena and Translator Free on windows or Swami on linux. This license means that you can do what you like with them but if you create any samples from them or improve on them then you have to use the same license in your projects. This way it keeps it open source (and therefore free). This license is only concerned with the source code. Any music you create with them is nothing to do with me (i.e. you take all the royalties and use whatever license you like).
XM DLX2 is one of two Deluxe models in the highly acclaimed XM series from Washburn. The other one is XM DLX2F. XM DLX2 comes with a solid, double-cut body made of basswood back and maple top. Top is a two-piece and it features the characteristic XM series contour. As all models in this series are, XM DLX2 is made primarily for players of heavy metal and shred styles. Strong pickups, super fast neck and 24-fret fingerboard indicate this. Bridge section features a tune-o-matic bridge with string-through-body construction and black plating. In it`s front, Washburn installs a pair of open-coil humbuckers. Master volume, master tone and a three-way toggle pickup switch comprise the controls unit. 24-fret fingerboard is made of rosewood and it`s installed on top of a set in maple neck.
I found a Decca guitar lying in my woodworks shop at school, and my teacher let me take it home. My friend and I have been restoring it, and we nearly have it finished, the only thing missing is the tremolo spring. However the model of the guitar is kind of odd as we have not found any record of what type of guitar we own. Its a double cut-away archtop, with a tobacco sunburst and 3 single coil pick ups. We have looked everywhere and haven't been able to find any record of a 3 pick up Decca guitar. We're still looking...
This is another budget guitar that is routinely praised for the excellent value for money it provides. Many reviewers point to its playability as its strongest point, which is not surprising given that this guitar is from Ibanez. There were even several people who wrote in their reviews that they liked the GRX20Z so much that they had bought it more than once.
Terada was one of the smaller Japanese manufacturers of acoustic guitars during the period of 1960 to 1980, producing products for Epiphone, Fender Japan, Grapham, Gretch and Vesta. Terada produced some Kingston badges until 1975. Other badged guitars produced by Terada include some Burny badges and interesting Thumb guitars. Terada has been in continuous operation since 1912.

A guitarist’s or bassist’s effects chain can largely determine the uniqueness of that player’s tone. Perhaps the most common effects pedal is a distortion or overdrive pedal, which either provides a distorting effect or overdrives the guitar’s signal into the amplifier—a tone that is highly popular in many genres of music. Other popular effects pedals include a wah-wah pedal (designed for sweeping a guitar’s tone control), fuzz, delay, flanger, phaser, reverb, chorus, compression, looping and boost. Many guitarists also use an EQ pedal to further shape and customize their sound. With all the brands and effects available at Guitar Center, your effects pedal options are virtually endless.
Power-valve distortion can also be produced in a dedicated rackmount valve power amp. A modular rackmount setup often involves a rackmount preamp, a rackmount valve power amp, and a rackmount dummy load to attenuate the output to desired volume levels. Some effects pedals internally produce power-valve distortion, including an optional dummy load for use as a power-valve distortion pedal. Such effects units can use a preamp valve such as the 12AX7 in a power-valve circuit configuration (as in the Stephenson's Stage Hog), or use a conventional power valve, such as the EL84 (as in the H&K Crunch Master compact tabletop unit). However, because these are usually placed before the pre-amplifier in the signal chain, they contribute to the overall tone in a different way. Power amplifier distortion may damage speakers.
Little-known manufacturer from Osaka, Japan, this company is responsible for the oddly named John Bennet badge. Nakai has been mentioned as a possible Matusmoto Musical Instruments Association member in the past. The company still exists and is producing musical instruments, quite a feat in light of so many manufacturers who faded after the golden electric guitar age.

I like the pseudo PTB scheme where the tone cap (I prefer .033 or .022mF) is attached to lug 3 of the pot and to ground. Lug 2 is connected to the Volume pot’s lug 1 and there’s an additional small cap (0.001mF or smaller) connected between tone pot lug 1 and Vol pot lug 2. Assume both pots are Log types: with tone at 7.5 (ie halfway along the pot’s sweep) there is no appreciable treble cut, and the volume pot gives a pretty even tone throughout its range. With tone pot higher than 7.5 bass is cut as you roll back the volume, with tone pot lower than 7.5 treble is cut. Minimum bass setting – vol approx 3, tone full up. Minimum treble setting vol full up, tone full down. I have this in most of my guitars and love it.


Well, that’s not exactly what he said. Although, it would seem that way, if you take time to browse the company's Facebook photos. Every guitar the company makes is truly enticing and a work of art. Moreover, the quality of each instrument is astoundingly good. Take the Xuul Katan VI. While the guitar is certainly unique, it also boasts a strong specs list:
An octave pedal listens to what note you’re playing and adds the next octave up or down (depending on your settings) making it sound like someone is playing the octave note with you. If you’re familiar with guitar or just learning, you’ll know that an octave is the distance between one musical note and it’s corresponding note at a higher or lower pitch. For example, if you play an open E string and then play the E string on the 12th fret, it will sound the same, just an octave higher.

Use of audio feedback to enhance sustain and change timbre. Feedback has become a striking characteristic of rock music, as electric guitar players such as Jeff Beck, Pete Townshend and Jimi Hendrix deliberately induced feedback by holding their guitars close to the amplifier. Lou Reed created his 1975 album Metal Machine Music entirely from loops of feedback played at various speeds. A good example of feedback can be heard on Jimi Hendrix's performance of "Can You See Me?" at the Monterey Pop Festival. The entire guitar solo was created using amplifier feedback.[26]
Yamaha is the most revered and leading manufacturer of full-line musical instruments. With its wide range of guitars, the company has become a best seller and is easily one of the best guitar brands in India. The C Series are the popular and affordable nylon string guitars by Yamaha suitable for beginners and young learners. The electric guitars of Yamaha available in India are of the Pacifica and RGX series. The Pacifica series offers the most value for money combining affordability with performance.
{ "thumbImageID": "RA-090-Dreadnought-Acoustic-Guitar-Natural/423794000010000", "defaultDisplayName": "Rogue RA-090 Dreadnought Acoustic Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Sunburst", "sku": "sku:site51274115039704", "price": "69.99", "regularPrice": "69.99", "msrpPrice": "129.99", "priceVisibility": "1", "skuUrl": "/Rogue/RA-090-Dreadnought-Acoustic-Guitar-Sunburst-1274115039704.gc", "skuImageId": "RA-090-Dreadnought-Acoustic-Guitar-Sunburst/423794000027000", "brandName": "Rogue", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RA-090-Dreadnought-Acoustic-Guitar-Sunburst/423794000027000-00-60x60.jpg", "imgAlt": "" } , { "name": "Natural", "sku": "sku:site51274115039668", "price": "49.99", "regularPrice": "69.99", "msrpPrice": "129.99", "priceVisibility": "1", "skuUrl": "/Rogue/RA-090-Dreadnought-Acoustic-Guitar-Natural-1274115039668.gc", "skuImageId": "RA-090-Dreadnought-Acoustic-Guitar-Natural/423794000010000", "brandName": "Rogue", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RA-090-Dreadnought-Acoustic-Guitar-Natural/423794000010000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51274115039751", "price": "49.99", "regularPrice": "69.99", "msrpPrice": "129.99", "priceVisibility": "1", "skuUrl": "/Rogue/RA-090-Dreadnought-Acoustic-Guitar-Black-1274115039751.gc", "skuImageId": "RA-090-Dreadnought-Acoustic-Guitar-Black/423794000001000", "brandName": "Rogue", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RA-090-Dreadnought-Acoustic-Guitar-Black/423794000001000-00-60x60.jpg", "imgAlt": "" } ] }
Upgrading the components in your guitar’s control cavity should give you significant improvements in tone and component life. If your guitar has single-coil pickups, buy 250K pots. If it’s packing ’buckers, go for the 500K jobs. If your ax has humbuckers and single-coils, I recommend 500K pots. This could make your single-coils sound a bit brighter than normal, but it will unlock your humbuckers’ full potential. For this job you’ll also need a soldering iron, solder, safety goggles, wire cutters, and a camera, to help you keep track of your original wiring connections (your cellphone will work just fine for this).
Setting up an electric guitar will bring out the true potential of that specific instrument. A poorly setup guitar will be harder to play due to high strings and neck bending, and will sound subpar with improper intonation. Electric guitar setup cost will cover all of these adjustments and more. For a price close to $50, your guitar will also have its neck adjusted so that the playability is as good as possible over the entire fret board. In the ideal setup scenario, the string height will be optimized so that playing is easy. The height of the strings should also provide for the best sound as they are able to ring free of the frets, allowing for the cleanest and strongest possible signal for the pickups to capture.
Guitar amplifiers vary in wattage. If you're playing to a massive audience, you'll want several 100-watt amps; however, for everyday use, that is overkill. If you merely want it for practice, a 10-watt solid state guitar amplifier will do, and if you're playing to a small venue, you'll probably want to consider a 20-watt valve amp. It's surprising how much sound a little amp will produce.
Guitar distortion is obtained and shaped at various points in the signal processing chain, including multiple stages of preamp distortion, power valve distortion, output and power transformer distortion, and guitar speaker distortion. Much of the distortion character or voicing is controlled by the frequency response before and after each distortion stage. This dependency of distortion voicing on frequency response can be heard in the effect that a wah pedal has on the subsequent distortion stage, or by using tone controls built into the guitar, the preamp or an EQ pedal to favor the bass or treble components of the guitar pickup signal prior to the first distortion stage. Some guitarists place an equalizer pedal after the distortion effect, to emphasize or de-emphasize different frequencies in the distorted signal.
However, unlike a boost pedal, the overdrive effect is not dependent on the amplifier to have a distorted sound. The overdrive pedal will internally boost the input signal so much that the top of the signal wave will be forced to naturally shrink itself. This is called soft clipping and it simulates amplifier like clipping as though an amplifier was being overly driven, hence the name overdrive. The distortion pedal will also boost the input signal but will then add resistors within the circuitry to not just shrink or soft clip the wave form but completely flatten the wave peaks. This is called hard clipping. For more understanding on the differences between soft clipping and hard clipping see the illustration below.
Overdrive can be subtle and produce warm slightly overdriven tones, think SRV. Distortion is easy to see as simply more overdrive, these tones are more saturated and compressed. The spectrum of overdriven tones is huge, from BB King’s slightly overdriven tube amp tones to Eddie Van Halen’s cranked Marshall, to Metallica’s thick distortion, to Smashing Pumpkins’ fuzz tones. It is all actually the same idea is a general sense, these tones may be gotten with amps, pedals, or a combination of both but it is all the same idea, overdrive. What was considered a heavy distorted tone in the 70’s is tame to the metal sounds of today.
If you’ve decided to make the neck from scratch, rather than purchasing it, you will want to cut that at this point. Make sure you are following specifications for how it will need to connect to the body. It’s best to cut the basic shape first and then refine.  You also need to hollow out space for the truss rod. Finally, for a rosewood fretboard, you will need to laminate the board to the neck.

Every guitarist seeks to produce an expressive and distinctive tone. Unfortunately, figuring out what kind of gear you need can be a baffling proposition. Here are the three main equipment categories that comprise your music-making rig: your electric guitar, guitar amps, and effects pedals and units. These components all work together to create your sound. And because you can swap out equipment and change settings, the creative possibilities are virtually limitless.
When you think about playing lead guitar, you think a lot about learning scales, learning guitar techniques like bending, sliding, vibrato, double stops, and other playing techniques that help give your guitar solos personality. One thing a lot of guitar players overlook, particularly in the beginning, is tone. A guitarist’s tone can be everything. Tone can act as a signature for guitar players. In this really neat Guitar Control video lesson, Robert shows you three electric guitar tone tips that can bring your guitar sound to life and make it instantly recognizable.
The Viper came in two versions made of ash, maple, alder or mahogany, the 1271, with two single-coil pickups, and the 1273 Viper III with three single-coils. Vipers had two-octave unbound fingerboards of either rosewood with pearl dot inlays or maple with black dots. A laminated pickguard (with model name engraved) held the pickups and extended down the body for the controls, including master volume and tone knobs. The plastic-and-metal bridge/tailpiece assemblies were the same as on the early Preacher. The single-coil pickups were about the size of mini-humbuckers with metal sides, black inserts, and flat polepieces. Windings were different depending on the position. The bridge pickup had poles slanted diagonally that emulated the slant of a Strat. Early Vipers have a three-way toggle. As with the Preacher, later Vipers have no name engraving, the all-metal bridge assembly, and an extra toggle which is probably a series/parallel switch.
The Boss Waza 212 Guitar Amplifier Cabinet has been specially designed as a partner to the awesome Waza Amp head. Packed with 2 custom made 12 inch speakers and ready to roar! You can even select whether you want the back to be open or closed, allowing you to make whatever sound you want! If you want extra speakers, there's also the Boss Waza 4x12 Guitar Amplifier Cabinet with 2 x 12" speakers to pump out your riffs with.
As mentioned earlier, technically, magnetic pickups are small magnets with fine wire coils. These small magnets produce a magnetic field around them. When the metal strings of the guitar are strung by the user, a vibrating motion is generated inside this magnetic field which changes the magnetic flux of the field. According to the law of electromagnetism, this change in the magnetic flux produces an electric charge in the wire coil around the magnet.
I believe that the best electric guitar amp for beginners is a straightforward combo amp, represented by the amps on this list. Avoid the bells and whistles of the fancier, feature-rich combo amps until you’re confident you have a solid set of playing chops. Then you can either move up to a modeling amp, or start adding effects pedals to your rig. The great thing about all the amps profiled above is that they provide a solid base for what ever effects you want to add to the mix later on down the road.
Speaker simulators are switchable filter sets designed to reproduce the EQ curves of a variety of speaker cabinet configurations (with varying degrees of success). The subsequent coloration is meant to replicate typical speaker sound and behavior, softening the harsh upper-midrange edges associated with amplifier distortion. Speaker simulator boxes are designed with direct  guitar-amp recording in mind, and are intended to remove the speaker cabinet and microphone link from the signal chain.
This guitar features two MP-90 pickups that can be switched on at the same time to produce sweet yet aggressive sounds. This guitar is mainly used to play country and indie music. This guitar has a radius of 9.5’’ and 22 medium jumbo frets for comfort and speed of play. It has a six saddle hard-tail bridge that allows precise settings and ease of adjusting string heights. The fingerboard is maple finished which makes for fast play. This guitar features three finishes sunburst, black transparent and vintage white.
Reverb is one of the earliest effects for guitar players, originally built into the amp itself like the Fender Deluxe Reverb and Super Reverb. Traditional spring reverbs actually send the guitar signal into the springs causing them to vibrate and simulating reverb. With the advent of digital technology reverb units pedals made their way onto the market but mostly as rack units, but as technology improved and shrank many of those units can fit into a pedal now.
For me, the hardest part of mixing is getting the vocals to sit properly. There are a lot of tricks you can apply that can help, but I think one of the most useful is to send the vocal to a bus and insert a compressor there, with a high ratio of around 10:1 or more. Set a low threshold, and a medium attack and release, then, in the next slot, load a distortion plug-in with a warmish sound. Use high- and low-pass filters, set to around 100Hz and 5KHz respectively, and mix a small amount back in alongside the lead vocals. You don't need to add much — it should be almost 'subliminal' — but it can really help to fit the vocal in the track. Nicholas Rowland

Without the rhythmic pummel of the Slits, there would be no riot grrl, no Rapture, no Yeah Yeah Yeahs; and without Viv Albertine — who played guitar for this groundbreaking U.K. punk band, and wrote the bulk of their early material — there would be no Slits. Albertine’s unrepentantly unpolished guitar stylings eschewed the high velocities and power-chord assaults of her male contemporaries in favor of trebly, dissonant stabs. It all meshed perfectly with the band’s cheeky, confrontational songs, ultimately turning jagged rhythms into something as provocative and primal as anything punk produced.

It is rare for any brand, let alone an entire company, to stay in business this long and their longevity speaks volumes to the exceptional quality of their instruments. Although they did dabble in electric guitars and basses for a short time, today the company is dedicated to making the finest acoustic guitars possible just as they were over 180 years ago.
Looper – A time-based effect that records a “phrase” of your playing and loops it back repetitively. These phrases can play sequentially in a song-style format or overdubbed to create dense layers, as used by one-man band style performers, vocalists to beatboxers. Larger loop pedals have more than one pedal for multiple tracks and allow you to add in-built effects to your loops. Remember: If you want to record your chain of effects pedals, make sure your loop pedal is always at the end of effects chain.
Wouldn't it be great if you could determine what price constitutes a "fair deal" before you made a deal? We think so. That's why we've created iGuide's Real Market Data (RMD) pricing, our proprietary system that does the research for you. It's a guide that gives you updated information on what you should pay for an item or what you should expect to receive - without having to spend hours researching. iGuide's Real Market Data pricing system is the internet's best guide to market value pricing and the only pricing system designed with the consumer in mind. Our exclusive RMD pricing is based on real sales data, gathered from auction sites in near real-time. This ensures you get the most accurate pricing available, as quickly as possible!
▽ Your account minimum payment amount is determined by the purchases and balances on your WebBank/Fingerhut Credit Account. The change in minimum payment amount is based on your account balance at the time it is advertised, and includes an assumption of interest charges and SafeLine fees, as applicable. The change in minimum payment amount does not include subsequent activity on your account such as any purchases, including deferred payment purchases, backordered, unshipped, returned or other pending purchases or exchanges; any payments, including partial, missed or returned payments; any fees, including recurring partner program charges, subsequent interest charges, late fees or returned payment fees. It is also subject to change based on shipping address, shipping method, partial shipments and taxes. Your minimum payment amount will not change and the purchase will not reflect on your statement until the order ships. If you have a balance or are making a multiple item purchase, see the Existing Balance Payment Chart.
Serious quality, 20 foot Guitar / Instrument connection cable. I have sold these for years. They come with a lifetime warranty, that is very rarely needed! Double  (redundant) 20 gauge, center conductors almost makes impossible ever having one go "dead" in the middle of a show! 100% Braided copper shield (not spiral wrapped like most cheaper cables) for silent / noise free operation (means less chance of picking up a radio station or wireless mic during your performance). Super-quality, Neutrik, all metal 280, 1/4" ends / plugs that are shrink wrapped for extra strain relief. The internals are hot-glued between to reduce internal flexion for even greater longevity. Built by the largest manufactured cable company in the US. Very rugged and durable, yet flexible jacket. These are not the cheap cables, nor are they built like most cables. Cheaply!
This D-15M dreadnought features a solid 'genuine' (South American) mahogany top over A-Frame X bracing; the same material is used for the back, sides and neck. The neck profile is a 'modified low oval', and it's hard to imagine anyone having a problem with it. Bone nut and saddle: check. Vintage-style, open-gear tuners check. Super-thin matt nitrocellulose finish all over: check. Tonally, there is a rich and projecting core sound that's complemented by the unmistakable, Martin D-resonance. It's vibrant and ebullient, yet not brash; warm and full without being thick or indistinct. It puts every single cent of its build budget into making the best sounding and playing instrument, with very little concession to cosmetics, electronics or anything else. Solid woods, improved neck joint, bone nut and saddle, no frills whatsoever, save for the 'burst – it's unreservedly recommended.

Guitarists don’t have to just look on in envy as pianists lead the holiday sing-a-longs this Christmas. Our selection of holiday Guitar Tabs include traditional classics we all love like “O Holy Night” and “Carol of the Bells” and the pop favorites that just wouldn’t be the same without a guitar, like “Jingle Bell Rock” and “Happy Xmas (War is Over)” by John Lennon. But if you just can’t get enough of those traditional Christmas classics, you can pick up our collection of ’Christmas Favorites for Guitar.’
Nice and great are just two of the many positive adjectives that people use to describe the Ibanez AEG12II-NT. And most of these satisfied users are pleased with its playability, describing it as a truly inspiring and fun instrument. Its visual appeal and sound quality are also commended often, some even coming from experienced players who compare it to more expensive acoustic-electric guitars.
Hi, I’m John Anthony, Playing and collecting Cool Guitars is my hobby, and all of my friends and relatives know it. For the reason, I receive many queries over the phone, email and social media about Best Guitar Recommendation. Which one they should buy now, which will fit them etc. And finally, I created this GuitarListy.com and started putting my suggestions and reviews here.
2) Use a line-out box (I use the Suhr Iso Line Out box) between your amp and dry speaker cab to take a tap off the dry signal. Run the line-out signal into a small mixer, and run the outputs of the mixer into a stereo power amp and two guitar cabinets. As with the previous rig, use the mixer sends and returns to patch in effects—which you will set at 100 percent wet (no dry signal) and blend to taste. In this setup, you can blend the dry signal into your “wet” cabinets. For live applications, mic all three cabinets, and pan the wet cabinets hard left and right in the PA. This is the setup I use, and I was inspired to go this route by guitarists such as Steve Stevens and Eddie Van Halen. I like to blend a significant amount of dry signal into the wet cabs. In the PA, the sound is absolutely massive! I also use an expression pedal to control the amount of effects in my wet cabs, so I can tailor my delays and reverbs on the fly.
Recently picked myself up a second J28SCDL Jumbo, which was set up beautifully and I have to say it truly is an amazing guitar. It could give some of the higher priced guitars a run for its money. Lovely sound, creative design and clearly a lot of guitar for your money. I seriously encourage you not to over look Washburn when looking for a good guitar at an affordable price. Might end up your favorite guitar!
it's really hard to beat the ric sound. the 335 12's and fender 12's are cool, but really the ric has the sound we're all familiar with. that being said, everyone has different tastes and I encourage you to play as many different ones as possible. Jimmy Page used a Fender 12 on Stairway. I went rick for that early beatles sound. the neck is tiny but it's part of the instrument.
Some guitars have a fixed bridge (3.4). Others have a spring-loaded hinged bridge called a vibrato bar, tremolo bar, or whammy bar, which lets players bend notes or chords up or down in pitch or perform a vibrato embellishment. A plastic pickguard on some guitars protects the body from scratches or covers the control cavity, which holds most of the wiring. The degree to which the choice of woods and other materials in the solid-guitar body (3) affects the sonic character of the amplified signal is disputed. Many believe it is highly significant, while others think the difference between woods is subtle. In acoustic and archtop guitars, wood choices more clearly affect tone.
×