With modern recording systems, track counts aren’t usually much of a limitation any more. In addition to a mic’ed up amp or a feed from pedals into your interface, try to also capture a clean feed of the guitar signal if your amp or pedal board allows a direct output to be routed. If you record this as well as the amp / fx feed, you have another option to re-process the guitar recording in software if you decide the original feed isn’t right.
Nice-Keys-CompletePlus-JNv2.0  A large set with three different piano types plus all the nice instruments.  All in a package of 943mb.  Pianos have different brightness and resonance settings available and all the nice instruments from EPs, Pads, Organs, Strings, Orchestra and Synths are included.  A printable link to the list of available instruments is here  Nice-Keys-CompletePlus-Instrument List

Stay tuned for the second part of our series/parallel discussion next month. We’ll pick up the soldering iron and explore some sweet parallel/ series switching options for our Strats. This will also close out our run of Stratocaster mod columns. When we finish the series/parallel discussion, we’ll switch over to Telecaster and Esquire mods. Until next time, keep on modding!

• Heavy is as Heavy Does: For low hanging alternate tunings like open D or dropped D, consider a heavy string gauge – at least .11s, although Stevie Ray Vaughan, who kept his instrument turned down just a half-step, employed a set gauged .13 to .58. Thicker strings will maintain their tension better when they’re low-tuned, which makes for less fret noise and other undesirable distortion. Many players feel thicker strings make for better slide playing, too, since the strings resist going slack under the pressure of the slide. But that’s really a matter of feel and learning to control a slide more than a string thing.
That said, information regarding Asian-guitar production from the 1970s and early 1980s is cloudy at best. Most lower-end Lotus-branded guitars were produced by either Samick or other factories in Korea or Indonesia. However, some of the higher-end Lotus instruments were built by the Cort factory in Korea or by one of three factories in Japan: Yamaki, Matsumoku, and Moridaira.
Bass effects that condition the sound, rather than changing its character are called "sound conditioners." Gain booster effects pedals and bass preamplifier pedals increase the gain (or volume) of the bass guitar signal. Bass preamplifiers for double basses are designed to match the impedance of piezoelectric pickups with the input impedance of bass amplifiers. Some double bass preamplifiers may also provide phantom power for powering condenser microphones and anti-feedback features such as a notch filter (see "Filter-based effects" section below).
I am 60 years old. I want a guitar (acoustic). I have decided on to retrain myself towards finger pickin style. I am researching knowledge and the tonal properties of the wood / tonal qualitites. I have very small (5.1). My hands are small. Neck demensions are very important towards please let me be trained so i can determine neck width and shape for my guitar
This Yamaha Pacifica features a Strat sound that is very good, especially since the humbucker can be tuned into a single pickup by lifting up on the tone control. Like with every other strat, it has a five-way switch which allows the player to select the bridge pickup, the bridge+middle pickups, the middle pickup, the middle+neck pickups, or just the neck alone. In the event that you are tired of the strat sound and you would like to return to Led Zeppelin, simply flip to the humbucker and get set to go!
• Gotta Feel It: Ultimately, what feels right under your fingers and sounds right coming out of your rig should determine your strings. It’s important to try different brands before zeroing in on a favorite. Judge a new set of strings by its brightness, sustain, tone and how easily they permit bending, fretting and picking. When a brand and gauge feel like buttah and sing like Circe, that’s the zone.

Lastly, there is a core group of survivors in this company. Nice people but probably not the most dynamic or skilled. That said, they manage to get the job done under some pretty trying circumstances. Getting hired and quitting or getting fired after 6 months makes their job much more difficult because they needed to train you and it takes time away from their work only to have that person leave. If you don't have what it takes to work here then stay away because this causes more harm to all involved including yourself. There are people working under stress with families to provide for who don't need to get hosed by some 'guitar dude" who couldn't cut it. In summary, don't get starry-eyed because you think guitars are cool and that will carry the day. Think about what this place will do to your credentials and ability to move on to the next stage of your career which working at Gibson will force sooner than you expect and by all means, be considerate of those special folks who will have to re-fill the gap after you leave.
The United States Department of Justice found emails from 2008 and 2009 in which Gibson employees discussed the "gray market" nature of the ebony wood available from a German wood dealer—who obtained it from a supplier in Madagascar—as well as plans to obtain the wood. It filed a civil proceeding in June 2011,[40][43][44] the first such case under the amended Lacey Act, which requires importing companies to purchase legally harvested wood and follow the environmental laws of the producing countries regardless of corruption or lack of enforcement.[44] Gibson argued in a statement the following day that authorities were "bullying Gibson without filing charges" and denied any wrongdoing.[39][45] Arguing against the federal regulations and claiming that the move threatened jobs, Republicans and Tea Party members spoke out against the raids and supported Juszkiewicz.[46]

I purchased this about 8 months ago (it is my first acoustic guitar) so I could learn to play again, I'm a singer by trait, but wanted to pick up a guitar again after a very long break. I did not want to spend a lot of money, but I didn't want junk either, while at the same time I wanted something that would translate well into performing live too. I did my research, and personally, it came down to this or the Yamaha APX-500 (But I really want the Mrk 1 not 2), so I settled for this.
I’m also going to go out on a limb and suggest the earliest Univoxes also included the ‘Lectra, a version of the one-pickup Aria 1930 violin bass (made by Aria). These were basically violin-bodied basses originally inspired by the Gibson EB-0, and popularized among imports by Paul McCartney’s use of the Höfner violin bass, copied by EKO. This was a hollowbody with no f-holes, Cremona brown finish, single neck pickup, bolt-on neck with position dots along the top of the 22-fret bound rosewood fingerboard. Strings anchored to a covered bridge/tailpiece assembly.
Thank you for the post. This explained a lot to me. However, one question I have is that I play lead and when I solo, I need to boost volume. I currently have an Ernie Ball volume pedal but I can never get it to go back to the right spot when I decrease the volume after a solo. I’d much prefer to use stomp box that I can just preset the volume before playing so I have a solo volume, and a strumming volume that matches the other guitar. Do you have any suggestion on what I can do to achieve this since the EB pedal doesn’t seem to work well for me?
{ "name": "Black", "skuUrl": "/El-Dorado/Vintage-Leather-Guitar-Strap-Black-1274228084716.gc", "status": "instock", "statusText": "In stock", "skuItemType": "New", "inventoryText": "In Stock & Ready To Ship", "inventoryKey": "in_stock", "availableDate": "11-16-2018", "price": 85.00, "isOnSale": false, "msrp": 85.00, "salePrice": 85.00, "easyPayOptions":"0,0,100002,6 Months Promotional Financing,01/01/2019,Special 6-month financing^ + $4 back in rewards Valid through,85.0,true,/pages/Gear-Card-Rewards.gc", "formatedIntegerValue": "85", "decimalValue": "00", "listPrice": 85.00, "isPriceDrop": false, "priceDropPrice": "", "promos":["freeShipping","international","return"], "warranty": false, "sku": "site51274228084716", "shipToStore": true, "displaySku": "361091000001000", "displayId": "1274228084716", "serialized": false, "shipsFree":true, "condition": "New", "commerceType": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/361091000001000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"false", "invMsgPreOrder":"false", "invMsgPromiseDate":"", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.guitarcenter.com/is/image/MMGS7/Vintage-Leather-Guitar-Strap-Black/361091000001000-00-140x140.jpg", "styleImgAlt": "Vintage Leather Guitar Strap Black", "freeGiftWarning":false, "freeGiftWarningTips":"", "kitCarouselItems": [], "availableInStoreOnly": false, "isShipsInternational": true, "checksum":"41079093650", "restrictionType":"", "restrictionError":"" ,"storeInfo":[ { "storeName" : "La Mesa", "storeStatus": "Ship to Store" } , { "storeName" : "San Ysidro", "storeStatus": "Ship to Store" } , { "storeName" : "San Marcos", "storeStatus": "Ship to Store" } ] }
Editorial comment – I advise folks when considering fretwork to consider not choosing a size or leveling operation resulting in less than .040” height if they want to play a style with frequent fret hand slurring, i.e. rock, blues, shred etc.  Low fret height is less capable of sustaining a reasonable fret leveling in the future, making it that much closer to refret time.  You don’t have to choose a very tall size if that is uncomfortable for you, but only choose a low height if that is really what you want and are accustomed to.
Ibanez 12 string Martin style, vintage Natural High Quality Japanese Ibanez Vintage Guitar ....This example is MODEL# V302 ...And it IS ANOTHER great find this one is in a Natural finish and is a REAL GEM ta-boot and it has a Beautiful aged Premium Solid German Sitka Spruce Top, WoW! what a nice glass like original finish to this one ...again High Grade woods used on this 80's Ibanez AAA Mahogany Sides-Neck & Back "see quality og the grain in the pics" . Lots of volume & is full-and rich tone from this baby.Pics show missing string done while we were cleaning her up they just snapped ... obviously old and so this guitar will come with a brand new set of Martin strings installed for the new owner no worries..... this one is ez to play & stays in tune well. It is a crafted in Japan guitar and it compares favorably to Gibson, Guild or Martin... at a fraction of that cost. Note: we also have a Sunburst V302 in stock in our listings please see that if you prefer the guitar in sunburst. Thank you for your interest, Joe.
The body of the PRS SE Standard 24 is made of mahogany and features a tobacco sunburst finish, vintage cherry, or translucent blue finish. Compared to most other body styles, this one is a lot more comfortable to play even though mahogany isn't the lightest tonewood out there.  The balance offsets any weight issues. The neck is a maple piece that comes with a standard rosewood fretboard and PRS classic bird inlays. The pickups PRS chose for this build are their S2 HFS Treble and S2 HFS Vintage Bass units. Their performance and color are pretty unique when compared to other designs out there. Looking at the hardware, we see a PRS S2 tremolo bridge on one end, while the headstock houses a set of PRS S2 locking tuners. Combined, these two components give you the ability to achieve great tremolo effects without losing intonation or tuning.
When starting with the electric guitar, it’s not uncommon to look at experienced player’s pedal board and think “Wow, so many pedals, with different names – wonder what should I get”. And while everyone knows that the core of your sound comes from the sensibility of your touch, your guitar and your amplifier, it is also true that certain pedals can transform and shape your tone to make it more unique and personal. Before shelling out all your beloved savings on unnecessary pedals, take a look at this guide to understand the 10 basic pedals, the so-called “must-haves”. 

My first electric was a Decca, and a friend had one too. Mine was the one pickup style and his had two pickups. This was back in 1972. These were cheap but played very well and I wish I still had mine. There's one on Ebay right now that's just like the one I had, only ten bucks so far. I remember the great sustain and feedback I could get through it playing Hendrix songs!
The microphone set up I described earlier will give you a similar effect. The close mic gives you great detail (in audio terms, top-end, treble) and warmth. The mid-distance mic will give you the perspective that the amp is in a room, but without too much loss of detail. The far mic will tell you in no uncertain terms that you are definitely in a room, and with any luck, the listener's brain will process that information and tell the listener what size the room is (I'm not talking exact measurements here--just rough approximations). There will be a fairly significant loss of detail though. The combination of any of the mics will give you varying degrees of perspective and detail.
In 1960, Gibson experienced a decline in electric guitar sales due to their high prices and strong competition from Fender’s comparable but much lighter double-cutaway design, the Stratocaster. In response, Gibson modified the Les Paul line. This 1961 issue Les Paul guitar was thinner and much lighter than the earlier models, with two sharply pointed cutaways and a vibrato system. However, the redesign was done without Les Paul’s knowledge. Although pleased with the sound, he asked Gibson to remove his name from the instrument until they fixed a design issue with the neck.[18] This separation occurred in 1960, but Gibson had a surplus stock of “Les Paul” logos and truss rod covers, and so continued to use the Les Paul name until 1963. At that point, the SG guitar’s name was finally changed to “SG“, which stood simply for Solid Guitar. In addition to the SG line, Gibson continued to issue the less expensive Jrs and Specials (and the Melody Makers) with the newer body style. These, together with the Firebird, were the standard Gibson solid-body models until the reintroduction of the Les Paul Standard Goldtop and the Les Paul Custom guitars to the market in 1968.

Like most affordable super strat guitars, the Omen-6 has a basswood body, carved into the elegant looking shape that Schecter is known for. The neck is crafted from mahogany and joins the body via a bolt-on joint. It is topped by a 14" radius rosewood fingerboard that has 24 jumbo frets. It comes setup for fast and comfortable playability, with its 25.5" scale length, 1.65" nut width and stylized fretboard markers. Giving this guitar its voice are two Schecter Diamond Plus pickups, which are passive pickups but are still hot enough for driving high-gain pedals and amps.
If you have any comments about what you see in this web site,  we would love to hear from you.  Our E-Mail address is below.  Of course we are particularly anxious to talk to you about our repair services or our handcrafted guitars.  But  --  don't let that limit you.  We would love to hear your ideas about any guitar related topic.  (One such e-mail led to the harp guitar project)   We WILL respond, generally quite soon.    If you have a question that you would like to see addressed in our Q& A page, let us know.  Our E-Mail Address is: hoffmanguitars@qwestoffice.net

The double-neck guitar is designed so that two guitar necks can share one body. This design allows the guitarist to switch between either neck with ease. The double-neck guitar will normally have a standard six-string neck and a twelve-string neck. Other combinations, such as a six-string neck and a fretless neck, are available. The double-neck guitar may be used in live situations when a guitarist needs a twelve-string guitar for the rhythm part and a six-string guitar for the solo break.


[Attention Korg Pa3x /Pa4x owners and Korg Pa700/1000 owners- I have a special version of this 6-velocity layer piano in .set format that will load to your Korg in compressed format at 116mb (equivalent to 232mb) - This set sounds wonderful on the Korg and uses 22 oscillators for outstanding realism including resonance, key-off and pedal effects. Send me an email (see bottom right) and I can provide a download link or go to the demo on SoundCloud here Korg Pa Yamaha C5 and follow the download link]
Samick is a South Korean based musical instrument manufacturer, which was founded in 1958 by Hyo Ick Lee, with the goal of "enriching human life through music, the universal language". By the mid-1990s, they were the single largest guitar manufacturer in the world! Because they build under contract for many famous brand names, more likely than not, you've already played one of their guitars.
Next, you will need to adjust the intonation. In this case, the technique is pretty much the same. You will need a small Phillips screwdriver. On the tailpiece side of the bridge in the first case, or the rear of the bridge in the second, there are screws holding the string saddles in place. Check each note by striking the string at the twelfth fret fretted and then unfretted. The unfretted note is the proper one; turn the screws either clockwise or counter-clockwise until the notes match.

Then I remembered Kent Guitars. I thought it would be pretty cool to have a guitar with my last name on it. Although they didn't appear on the U.S. west coast very often, if at all, (I would remember them if they did), It turns out there is a whole crapload of them out there. Information is scattered around the internet in bits and pieces and nobody who was making them at the time is talking about it. So I have started gathering information, limiting myself to the 500,600,700, and 800 series models. The only ones I am interested in owning are the 700 and 800s. I have a 740, an 820, 823, 833, and 834. I may never get the chance to buy another.
{"product":{"id":"113884849","stock":"instock","price":"219.99","name":"Thunderbird IV Electric Bass Guitar","download":false,"sku_id":"113884849","checksum":"117352072023","rep_id":"site5113884849","displayId":"113884849","sku_display_id":"113884849","sku_rep_id":"site5113884849","gc_pro":false},"category":"Electric Bass","pageName":"product_detail","subcategory":"4 String Electric Bass","dept":"Bass"}
Guitar FX BOX does REALLY real-time DSP. Signal is sampled from sound card input, processed and then sent to the output with VERY LOW LATENCY. Unlike many other "real-time" audio programs, I/O delay with Guitar FX BOX is extremely low, virtually undetectable! This is achieved using DirectSound (or WDM streaming) for fast access to the hardware (sound card) and fast DSP algorithms optimized for real-time processing. Through DirectSound, latency is about 20ms with most sound cards, or even less. When WDM streaming driver is used, latency can go as low as 5ms! Nevertheless, exact total i/o latency still depends on hardware/drivers.
Buy a kit if you want to make things easier. Several companies produce electric guitar kits that include all of the parts you’ll need, prepared and ready to assemble. If you just want to get your feet wet, these can be a good choice. While you won’t get the full experience of making a guitar from scratch, you’ll still get the satisfaction of putting it together and finishing it yourself.[6]

Arch top body size is equivalent to the flat top 000 body size, 15" wide across the top, carved spruce top, back is not carved but is arched by bracing, rosewood back and sides, 5-ply top binding with pearloid outer layer, elevated tortoise pickguard with b/w binding, backstripe of two horizontal lines surrounded by two rows of diag lines (like a Style 45), bound ebony fingferboard, style 45 fingerboard snowflake inlays, trapeze tail piece, vertical "Martin" peghead logo, bound peghead, gold plated parts, sunburst top finish.
This is one of the coolest guitars to come out of the Gibson Custom Shop: 2018 Gibson Custom Shop Explorer, Extra/Elbow Cut, with a heavy aged relicing, Faded Cherry Finish, Gold plated Nickel hardware. This model is patterned after the 1958 Explorer owned by Eric Clapton. It is brand new with OHSC, COA, and all paperwork/tags. The weight is light at only 7 lbs, 12 oz. This is only one of a limited run of 5 in the Faded Cherry.

A question which causes much thought and divide! Catch 22 to a degree: you can't play songs till you've learnt some chords, but just knowing some chords will mean you actually can (though you are not aware of it) play loads of songs. There is a plethora of songs out there with only three chords (some with only two!). Their differences are that the order of chords is slightly different for each - with the exception of the thousands of 12-bar tunes!
Archtop-wise, the PEs apparently went into the ’62 and sometime in that year were renamed with the EP prefix, but otherwise remained the same. No detailed info on the full line is available, but the ’62 PE-8 had a bound fingerboard, small block or strip inlays, a single rounded cutaway, a rosewood pickguard, two � not one � metal-covered pickups (with one row of exposed poles along the edge), a chicken-beak selector on the upper shoulder, and four controls on the lower bout.
In fact, at the beginning of this article I mentioned John Mayer’s song, “I Don’t Trust Myself.” The way that guitar tone is achieved is by using a filter pedal called the AdrenaLinn III. That effect is a beat-synced filter effect, meaning it has the ability to sync up the sweeping filter with the rhythm of a song. This is accomplished by either tapping in the tempo on the pedal, or setting the tempo with the tempo knob.
Tonality is an important consideration for many musical instruments, and that’s especially true when it comes to acoustic guitars. The strings, fretboard, sound holes, and body of a guitar all play a role in how the guitar will sound to an audience. The distance between the strings and the fretboard (called the “action”) can also affect sound quality.
{"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: hohner","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","prop17":"sort by","evar51":"default: united states","prop10":"brands","prop11":"hohner","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
Unbelievable value for money with quality that is second to none The Joey series of electric guitars have been specifically designed for smaller hands, with 3/4 sized bodies and smaller 21.5" fret scale. They are a great sounding, fun guitar and come complete with a built-in tuner to make sounding good even easier. Awesome value as a part of Ashton's
My 5056 has pretty high action on it, and these guitars are very bad candidates for neck resets, as the necks were glued with epoxy, not hide glue (which can be softened with heat). Anyone who looks at buying a vintage Alvarez should bear this in mind if the action is high. There may be no practical remedy (Search web for comments on it.). And those who own them should probably stay away from heavy string gauges, i.e., not bigger than .12's on high "E". I now de-tune my Alvarez guitars when I put them away for longer period storage even though I use 11's on them. If you do use heavier gauge strings, you might want to de-tune when putting away the guitar. Just a suggestion. Cheers.
The Estimated Values shown on each web page are out-of-date in many cases. One person cannot possibly keep every page up-to-date, so that is why we created a Wiki system to allow anyone to help maintain the database. We invite anyone who sees a problem with any Estimated Value to report it to us by clicking the Report A Problem icon at the top of each page (it looks like this ).
Birmingham’s Table Scraps add a grunge-y Midlands mud to the garage rock sound established by the likes of 13th Floor Elevators and The Cramps. Guitarist Scott sticks to a “three-pedal limit”, using a Death By Audio Fuzz War (“a versatile monster”), Echo Dream 2 and Boss DD-3 to jarring effect to create freaky, DC59’d melodic lead bursts. As Scott says: “Once you try 12-string everything else only sounds half as good.”
In addition to building world-class custom basses and guitars, our luthiers also perform a wide variety of guitar repairs, restorations, modifications and upgrades. Whether you have an electric guitar, acoustic guitar or a bass, new or old, feel free to bring it by the shop for a free assessment. We have the experience, skill and equipment to provide maximum playability.
In about 1975, Ernie Briefel and Merson parted company with Unicord/Gulf + Western, becoming Music Technology Incorporated (MTI), on Long Island, taking the Giannini brand with it. Later, in the early ’80s, MTI would import Westone guitars made by the great Matsumoku company, which it would sell until St. Louis Music began its partnership with Matsumoku and, in 1984, transitioned its Electra brand to Electra-Westone and then ultimately Westone, which lasted until 1990, when SLM’s guitars all became Alvarez.
I have an old Zoom 505 all in one pedal plugged into the clean channel of my Peavy Scorpion 2-12 amp. I’m using the distortion, chorus, reverb, delay, etc. programmed from my pedal. I want to add my Crybaby wah so it’s just a matter of easily just switching the order of both pedals and see what works best. Until I upgrade, it should be simple. Here we go. Thanks.

{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: first act","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"gretsch guitars","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category"}

Musicians might not want to be replaced by machines - we (or they, as it were, because I lost whatever musician credentials I might have earned annoying people with my wooden flute as a beggar on the streets of a tourist town when I started programming computers to play music) might make a strong case that no machine can express the human soulfulness of music. It is easy to conclude that, the more of the musical task that is assigned to a machine, the less soul is expressed in the music. Well, great big rock-n-roll wall of sound that all over your acoustic guitar soul. That stack of Fender amps I can hear five miles from the stadium where David Gilmore is strumming a guitar is as much an instrument as was the Shepard's lute - and a much more popular instrument now, for audiences attuned to the daily roar of tires crushing air against pavement.
Univox was not, as you might guess, just another isolated Japanese import, but was part of a much larger story of its importer, the Merson company. And in this context, Univox is a part of the much larger story that included names you probably see everywhere but know little about, since they’re off the beaten path, names such as Tempo, Giannini, Westbury, Korg and much more! You’re going to have to pay attention here, because a whole bunch of familiar and not-so-familiar names crisscross through this story.

Bass amplifier equipment manufacturers include a variety of different types of companies, ranging from companies that only make individual components (e.g., Accugroove loudpeakers, a speaker manufacturer) to companies that only make bass amplifiers and loudspeakers (e.g., Gallien-Krueger). At the other end of the spectrum are companies that offer bass amplification equipment as part of a much broader offering of different types of instrument amplifiers and public address systems (e.g., Peavey, Carvin A&I or Yorkville Sound.)


Delay – a time-based effect that sounds like an echoing of your guitar tone. A delay pedal creates a copy of your guitar tone that repeats like a fading echo. Delay pedals usually have a time knob that allows you to choose the time of the delay intervals, an effect level knob that controls the volume of the delayed sound and a feedback knob that controls how many repeats are sounded before the effect fades. See different types of Delay below:
So many new guitarists, and even not so new guitarists, play with the volume and tone knobs turned all the way up all the time and then shell out lots of money for pedals when they are not satisfied with their tone before taking advantage of what the guitar can do (and it's a lot). Then of course, your amp's tone controls can refine things even more.

If you are not shopping online, then get to the nearest local instrument store and try out different guitars by playing them while switching between different positions in standing and sitting down. Plug them in and turn them on. Stand in front of a mirror with them on hand. Try holding it up like George Harrison, and downwards like Slash. Its different tires for different cars—so there are no hard and fast rules, but your eyes, hands, and ears will tell you what suits you best.


SOLD OUT: Super condition its been kept in the case over 25 years WoW!... JVG just set-up and plays wonderfully no buzz no drag its EASY to play now and it has NO WEAR almost like owning NEW Vintage! Sounds good ! its loud and robust TONE this is a great deal on an absolutely wonderful guitar. This was well crafted in Korea in the late 1980's same as Japan spec incredible. Lots of vintage guitar for a great price Its woods are as follows... Top is Spruce nice straight grained and may be solid cant see a seam it is what it is as made, the back and sides are all a fine instrument grade mahogany as is the neck a medium slim profile neck feels great , the headstock has the rosewood overlay with Fender logo in mother of pearl with gloss finish to front headstock as the body is gloss front - sides and back and the back of neck smartly in satin finish to not show finger prints easily.. Fit and finish is rated JVG at very good - excellent vintage easily Near Mint rating I'm still looking for a dink and cant find one yet, but thats not to say there may be something minute somewhere but I looked it over good and she qualifies for near mint rating vintage and is WAY BETTER than average. The fingerboard I believe is ebonized rosewood and shows no divots at all... same with frets I polished them pre set up and I can attest they are excellent too... Neck angle and action is very good straight and as a result the action is set to within Martin spec and plays excellently with no buzzing. Original tuners on board and are good quality and do the job well, intonation on this guitar is good so it sounds sweet up or down the fingerboard... surprisingly great tone for a guitar anywhere near this price point, You will be very pleased. Comes with its original semi hard chipboard case black good all latches and handle are good, Here is a great sounding and playing Vintage Korean guitar that will be sure to please. Questions ? asl Joe jvguitars@gmail.com .
WoW Talk about nailing the essence of the Original by Gibson.... This is a well crafted Japanese Prime Lawsuit era Classic with the great looks and BIG fat TONE is what this old vintage Japanese script logo Alvarez J200 guitar has to over you today nearly 40 years ago and a true Japanese Vintage work of art really. Beautiful Headstock with Alvarez Script logo in mother of pearl inlay with crown as well is its original truss rod cover is striking.Overall The fit and finish is hard to beat the materials are superior grain looks as is fit and finish and she has stood the test of TIME. Minor Vintage checking seen on its top and only adds realism to its true vintage status no reduction from its appeal its very cool looking as you can see from its pictures even perhaps more beautiful than the 70]s Gibson from this same era this Alvarez is based on the early1960's era known to be the preferred vintage era to own amongst the Gibson aficionados This is a prime example and is overall GREAT with super easy low action we completely cleaned this instrument upon its arrival it was owned by a smoker and needed it but never abused luckily then we dressed the frets and polished the entire guitar and frets as a result it looks this amazing and I have seen every square inch and can tell you this is a very good example from my inspection while working on it. She plays really nice now, with very good volume and a rich vintage 40 year old Vintage Alvarez kind of tone I expect from a good J200... This guitar has that, No brakes no repairs non needed no reason this vintage Japanese Lawsuit J200 should easily play another 40 years with good care she's set up and playing Amazingly.... SUPER FUN to play Act quick our last Alvarez 5052 Script logo went pretty fast... She's here and available and in stock.... email Joe to buy it NOW: JVGuitars@gmail.com .
Their designs do not require them to have comparator inputs as with solid-state amps. The small amount of negative feedback in valve amps is only required to provide damping to the speaker. Valve Amplifier Design From physics we know certain things must be a particular order and size to be efficient and this is acutely so with valve amps. 60Watts is the minimum power capacity for an amplifier to bring quality speakers to life with full fidelity.

An electric guitar with 6 strings, dark blue metallic in color without case. It is has its body made of rosewood and its neck from the maple. The fret boartd is made from rosewood and has dimension of about 106.7 x 52.6 x 12.4 cm. The guitar goes for about INR 13,990 depending on prevalent market factors. you can get more information by clicking on the following link:
I can't even begin to tell you how much I love mine, both for sentimental reasons and due to the fact that you couldn't buy that kind of quality nowadays for under a grand! I too, like the OP, am getting ready to do some restoration/ TLC on mine. New nut, saddle, bridge pins, tuners upgrade, and eventually fretwork. If you guys ever see one at a pawn shop, pick it up quick!! They can usually be bought for under $300!!!!
Rocksmith displays six horizontal lines at the bottom of the screen that represent the guitar's six strings—E, A, D, G, B, and E—and show you which ones to play. The game color-codes them to try and make it a little easier to comprehend all this visual information at once, but there's no way around it—it takes quite a bit of practice and memorization to get used to this. You really need to practice to the point that you know intuitively which color belongs to which string. Otherwise you'll always be looking down to pick out which string you should be playing, and will never be able to keep up with the song.
Finally, have you ever heard a definitive answer to the question “how long does it take to learn guitar?” Us neither! Learning your first chords can take a few hours, but the instrument can take a lifetime to master. But that’s the joy of playing guitar – you never stop learning. It’s down to you to practise and progress, because practise makes perfect!
I always respond to these enquiries as I have played some in UK shops and like them a lot .Well designed and made though I am sure the odd duffer gets through like most imports .Trev Wilkinson did the designing ,though it should really read ,modifying ,as most are other makers basic designs,.The Les Paul lemon drop is superb judging by reviews and I loved their S types ..Worth the money it seems .I would prefer a Vintage Strat , 335 or Les Paul to the other cloned alternatives .I did buy an Epiphone Dot but after playing a Vintage 335 ,wish I had bought it instead .The ones I played were Chinese
I know a lot of you out there fancy yourself as “tinkerers”, and many of you may actually be quite good at handling repair work to your own instruments, but I’ve always been more of the kind who loves to find a good repair person. Number one, if the repairer doesn’t do the right job, or there are problems with the work they did, they have to own up to it, and make sure it’s done right until you are fully satisfied. Then of course, if they are actually a selected and accredited repair person for a given guitar company, it’s even better to bring them the guitar, rather than trying to take matters into your own hands.
Arai, Aria, Aria Pro II, Aria Diamond, Apollo, Arita, Barclay, Burny, Capri, Cimar, Cortez (electrics only), Columbus, Conrad, Cutler, Dia, Domino, Electra, Epiphone, Granada, Hi Lo, Howard, Ibanez, Lindberg, Lyle, Luxor, Maxitone (this guitar differs from Tama's Maxitone badge), Mayfair, Memphis, Montclair, Pan, Pearl (electrics only), Raven, Stewart, Tempo, Univox ,Vantage,V entura, Vision, Volhox, Washburn, Westbury, Westminster, Westone
The SG retains a similar dual-humbucker configuration as the Les Paul Standard but it truly has a life and style all its own. Due in part to its aggressive style, impressive mid-range bite and thunderous output, the SG has become synonymous with rock ’n’ roll. The Gibson SG is one of only a handful of models that has never been out of production since its introduction in the early ’60s.
Modulation effects (like phaser and flanger) follow effects like wah and overdrive. This allows the modulation effect to process and modify the tone built by the effects before it. If you put a modulation effect before the overdrive, then you are overdriving the sound of the flanger. This is a lot more difficult to control so the ME-80 places it after these effects.
Line 6 gets a bad rap amongst the guitar community, due to the fact that they apparently operate on a ‘quantity over quality’ business model. The truth is, however, their digital modeling tech has improved vastly since that reputation stuck and they definitely deserve renewed consideration. And that’s all the more true when it comes to beginning players. As you’d likely be learning how to play songs by your favorite artists, this amp with its massive array of presets (128 to be exact) will allow you to mimic your idols with little, if any, effort. And, honestly, it’ll sound pretty great. It even has a built-in tuner, metronome to keep you on time, and real drummer loops so you can get in the swing of playing live.
CLEAR COATStew Mac sells nitrocellulose lacquer that works realy well for guitar finishing but if your like me you can't afford $10 a can for paint. Or you can check out reranchthough I haven't used any of their products they are a little cheaper. I use Deft spary lacquer. You can get it at Wal-Mart for under $5 a can and it works great. Use the same basic steps that you used when you sprayed you color coats, keeping in mind that you want enough coats so you don't cut through the clear top coat when wet sand and polish it out. Now comes the waiting. The paint has to set for several days to a month to let the solvents that are in the paint to rise to the top and harden. The paint will feel dry but you will notice that it might feel a little sticky or soft when you touch it. I like to do a "nail" test on mine. I use my finger nail and push it into the painted area in the neck pocket to see if it is still soft. No one will see the inside of the neck pocket so it's ok if you scratch it. Once it has cured completly you shouldn't be able dent the finish. It could take longer than a month for certain finishes to harden completely but trust me, you will be glad that you waited. For more information about all the different types of lacquer or clear coats products that are out there and how to choose what may be right for you, check out the drum foundry they have some great info.
Another option would be to instead buy a mobile guitar interface and download one of the many guitar apps available, but I typically don’t recommend this for beginners. These apps are very robust, and can be a little overwhelming for someone just starting out. First learn how the controls on a real amp affect your tone. Once you’ve grasped these basics (and acquired some basic guitar skills), you can think about buying some fancy apps and effects.
As a beginner most people are not very sure of the sound, style or type of guitar that they would ultimately like to play, but after playing for 6 months or so I’m sure you will know a lot more about guitars and when it comes time to choose your next guitar it will be an easy choice. The key features a beginner needs is a guitar that is well set-up and easy to play, but you don’t really need to spend too much money on getting a better quality of sound. Higher level guitars will only sound better when your playing has progressed to the level that you can play quite well.
You wont be sorry with this harness, full size volume pot , push pull tone pot/switch both with good throw torque, great solder connects and a quality, all hardware was intact , just remove replace, I did have to carefully bend the lugs on the input switch to get it to seat properly in my Epiphone but other than that minor obstacle all went well, no hum or noise and the toggle feels solid, man Epiphone put some straight up junk electronics in my guitar so this was a great upgrade, thanks Kmise you got a new customer..will order another for my Jackson Kelly..
At the top of the fingerboard, just below the headstock, is a slotted piece of material called the nut. The strings are routed through the slots in the nut and terminate at the bridge, located on the far end of the body. When the strings are plucked or strummed, they vibrate between the nut and the bridge. This vibration is where the sound of a guitar begins. How that vibration translates into sound depends on whether the guitar is acoustic or electric, as we’ll see in a moment.
While an acoustic guitar's sound depends largely on the vibration of the guitar's body and the air inside it, the sound of an electric guitar depends largely on the signal from the pickups. The signal can be "shaped" on its path to the amplifier via a range of effect devices or circuits that modify the tone and characteristics of the signal. Amplifiers and speakers also add coloration to the final sound.
Up for sale is an Ibanez RGA32 guitar equipped with Metal Works Brushed EMG 57/66 pickups and Sperzel locking tuners. This guitar is in great condition, has never been gigged and has been kept in my smoke free music studio. Guitar Specs: Mahogany body with quilted maple top 3-Piece maple Wizard II neck Bound rosewood fretboard with 24 jumbo frets Gibraltar Standard bridge Pearl dot inlay

If this were a list of the best electric guitar brands for metal it is very likely Jackson would be near the top. This is a company practically synonymous with metal, and for decades the most extreme players on the planet have looked to Jackson to get the job done. But Jackson also has a strong presence in the rock and hard rock genres, and if that’s your bag you’d be smart to give them a good look.
Early valve amplifiers used unregulated power supplies. This was due to the high cost associated with high-quality high-voltage power supplies. The typical anode (plate) supply was simply a rectifier, an inductor and a capacitor. When the valve amplifier was operated at high volume, the power supply voltage would dip, reducing power output and causing signal attenuation and compression. This dipping effect is known as "sag", and is sought-after by some electric guitarists.[46] Sag only occurs in class-AB amplifiers. This is because, technically, sag results from more current being drawn from the power supply, causing a greater voltage drop over the rectifier valve. In a class-A amplifier, current draw is constant, so sag does not occur.
Body tops are optional. If you're just starting out, you should either skip this option, or choose the veneer top that appeals to you most. We offer veneer tops (paper-thin layer of wood) and cap tops (thick layer of wood). Most people will add a top to their instrument because of the top’s naturally beautiful appearance. Some people will add a top to their guitar because it can affect the overall sound of the instrument, too (only applies to cap tops, not veneers).
SOLD OUT: Super condition its been kept in the case over 25 years WoW!... JVG just set-up and plays wonderfully no buzz no drag its EASY to play now and it has NO WEAR almost like owning NEW Vintage! Sounds good ! its loud and robust TONE this is a great deal on an absolutely wonderful guitar. This was well crafted in Korea in the late 1980's same as Japan spec incredible. Lots of vintage guitar for a great price Its woods are as follows... Top is Spruce nice straight grained and may be solid cant see a seam it is what it is as made, the back and sides are all a fine instrument grade mahogany as is the neck a medium slim profile neck feels great , the headstock has the rosewood overlay with Fender logo in mother of pearl with gloss finish to front headstock as the body is gloss front - sides and back and the back of neck smartly in satin finish to not show finger prints easily.. Fit and finish is rated JVG at very good - excellent vintage easily Near Mint rating I'm still looking for a dink and cant find one yet, but thats not to say there may be something minute somewhere but I looked it over good and she qualifies for near mint rating vintage and is WAY BETTER than average. The fingerboard I believe is ebonized rosewood and shows no divots at all... same with frets I polished them pre set up and I can attest they are excellent too... Neck angle and action is very good straight and as a result the action is set to within Martin spec and plays excellently with no buzzing. Original tuners on board and are good quality and do the job well, intonation on this guitar is good so it sounds sweet up or down the fingerboard... surprisingly great tone for a guitar anywhere near this price point, You will be very pleased. Comes with its original semi hard chipboard case black good all latches and handle are good, Here is a great sounding and playing Vintage Korean guitar that will be sure to please. Questions ? asl Joe jvguitars@gmail.com .
It’s provided as-is with no support, but it’s still well worth checking out if you’re on a PC. According to the developers, it was born inside an academic research project about the modelling of electric devices, and then applied to the musical instrument field as an evolution of the techniques available in commercial units. Its most important feature is the high precision of the simulation.
While the HSS Bullet Stratocaster isn’t available in a left-handed model, the similar, somewhat more costly Affinity Series Stratocaster is available in a left-handed version. This guitar differs from our top pick in that it uses slightly higher quality of parts and has a higher quality finish (based on our experience with the Affinity Series Jazzmaster); it has a single-coil pickup instead of a humbucker in the bridge position (which will be noisier and also brighter-sounding); and it has a vibrato bar.

A combo amplifier is a unit in which both the amp and speaker is integrated. You plug a guitar into one of these, turn it on and you are ready to play. The obvious benefit of a combo is that you have everything you need in one standalone unit, while the sound tends to be optimized by the manufacturer to be the best it can be – there’s no worrying about matching it with a good speaker. Combo amps also tend to be cheaper than heads and, as such, are excellent for beginners. While some are very capable of small to medium-sized performance, the drawback is that combos are limited in power compared to a head. They also tend to be much heavier, which can be a pain when regularly transporting it.


The rotary speaker effect is based on an actual rotating speaker system invented by Donald Leslie called the Leslie speaker. It was often paired with a Hammond organ, but in the 60’s guitar players also began using it for the unique tone and effect it gave the guitar. The original Leslie speaker cabinet used a two speaker system with a rotating horn and bass woofer drum. This created a cool, swirling effect where the music seemed to move around the room. Obviously, guitar pedals can only simulate this rotatary effect, which can be enhanced with a stereo amp setup. Of course you could use an actual Leslie speaker (or one of the newer competitors), but costs are high and it requires lugging around an extra speaker cabinet.
Taylor has swiftly made several electric guitars that made their way to the hands of professional guitarists onstage. Moreover, a few of their models are directed towards working players too. In fact, Taylor seems to be caring about the beginners and intermediate level players as well, since they produce several guitar models aimed at these customer groups. If you are ready to scour out your wallet to get your desired guitar, Taylor will be the perfect choice for you.
Healthy forests are vital to all of us, for many reasons. We must preserve these precious resources for future generations. To that end, Oregon Wild Wood strives to provide only salvaged wood, trunks and stumps left behind from old timber harvests, trees that have died and/or must be removed, trees from commercial groves that become unproductive, and even wood salvaged from old buildings and structures. Your next guitar can be a source of pride in yet another way.

Let’s kick things off with one of Schecter’s top tier models. Blackjack Slim Line C-1 FR is by far one of their more refined guitars. It’s slim, lightweight, and brings the kind of thunder that will give you goosebumps. With a set of premium Seymour Duncans, we expected nothing less. My brief encounter with this axe was one of the most enjoyable playing sessions I’ve ever had, and I’ve played many, many guitars.
The Les Paul Traditional 2019 is one of the latest iterations of this iconic guitar, bringing over the same pleasing aesthetics and rock friendly tone using modern production methods for improved reliability, consistency and expanded tone options. The body features a classic mahogany body with no weight relief, and a AA grade figured maple arched top. The 24.75" scale length mahogany neck is topped by a 22-fret fingerboard that has a nut width of 1.695". Giving this guitar its classic voice are Burstbucker 1 & Burstbucker 2 humbuckers, with Orange Drop capacitors that replicate the ones found inside vintage Les Pauls.
Every beginner guitarist deserves to learn on an instrument that's built by experienced craftsman who use only the finest materials. However, for many novice players, it's difficult to know for sure what's considered a high quality instrument. To make things easier, many popular guitar brands offer guitar value packages. These packages consist of all the essential pieces of equipment that a learning guitarist would use in the developmental stages of their playing. Within this section, you'll find more than enough guitar value package options to choose from.
The advantage of this specific package is that you’ve got everything you need to get started right away: guitar (duh), amp, strings, tuner, guitar cable, picks, gig bag, strap, and instructional DVD. Those of you who just wanna get a guitar and start, this is your choice. Squier also makes similar package, but I recommend this over the Squier because the parts (electronics) are higher quality, although the Yamaha costs a little bit extra.
Standard eight-string tuning. Used by Scar Symmetry on the song "The Three-Dimensional Shadow" from the album Holographic Universe (album) and "Mechanical Soul Cybernetics" from the album Dark Matter Dimensions, Deftones, Periphery on "Ji", "Overture", "Extraneous", "22 Faces", "Four Lights" and "Stranger Things", by Fear Factory on "Mechanize", "Metallic Division", "God Eater" and "Soul Hacker" and by Devil You Know on some songs.

I have a Palmer P 33 acoustic (hand-crafted etc), that I bought second hand about 20 years ago for £80. It still sounds and looks superb and rarely loses its tuning. (Probably better than my newer Tanglewood.) I can't find out anything about it. However, somebody out there must have made it. Surely that somebody knows something about them! Do they never go on the internet! Pete.

For many people who pick up the guitar for the first time, learning scales is often not at the top of their priority list. This is normal and as a beginner guitarist, there is other more important foundation knowledge that should first be acquired. However, at the point when you start learning scales as a guitarist is when you know you’re starting to get serious about playing. Learning guitar scales is a fantastic way to practice your technique and theory. Scales also come in handy for a variety of purposes such as: Writing music Improvising/jamming with others Understanding how music
Your skill level on the guitar is another factor that should be taken into consideration while shopping for the perfect instrument. It is generally wise to start out with a lower quality model when you are first beginning to study the guitar, whereas a veteran player with a trained ear will likely require the bells and whistles of more high end gear. If you’re a beginner, it’s a great idea to start out with a Yamaha or a Fender Squier, for example, as you get plenty of quality to learn on without breaking the bank. It’s wise not to go overly basic, however, as cheap guitars will have harsh playability that will leave a beginner with painful calluses that may scare them away from the instrument.
: Just in a vintage excellent beauty with a fresh JVGuitars set up is ,New Martin strings bone nut & saddle and solid ebony with brass ring and Abalone inlay bridge pins, all old plastic cheap tone robing parts are tossed out for the JVGuitars TONAL UPGRADE to 2017 specifications otherwise she's ALL ORIGINAL see for yourself She's pretty darn clean and in better than 40 years old average vintage condition For a song. The Takamine F360 was DISCONTINUED decades ago This is the Lawsuit version Specifications Top Sitka Spruce Back Rosewood Sides Rosewood Finger Board Rosewood Electronics None Finish Natural Gloss Faithful D-28 style Dreadnought The most popular body shape of the past half century, the Dreadnought delivers a strong low end with plenty of volume. Structural integrity is excellent as is neck applignment its action is very good low and it plays with ease, new strings and sounds great this fine vintage Japanese instrument is ready for another 40 years of enjoyment. She is not new its actually 40+ years old and has been played, frets are still excellent and have been JVG dressed and she has a few minor and insignificant doinks or scratches and nothing to detour from its vintage patina beauty she's a true vintage quality instrument and is faithfully based on the great D-28 a playable work of art you can hear and enjoy for decades to come. Well taken care of California one adult owner that took really good care over 40 years just for you! Get her before she's gone. any questions or to purchase now contact Joe at JVGuitars@gmail.com .
Before recording, make sure that the guitar is in tune, with a fresh set of strings, and that you check the tuning regularly. New strings always produce a brighter sound and better sustain. If the instrument has been properly set up, string and fret buzz should be minimal; while this type of noise is much less obvious when playing through heavily- distorted or overdriven amplifier settings, it can be very distracting when using clean settings or recording directly.

Gibson is easily one of the most identifiable guitar brands in the world today, and even with the premium price tags of their instruments, many continue to look up to them as their dream instruments. Thankfully, the company has toned down the price a bit on some of their guitars, one of which is the J-15, which enters this list with its good balance of workhorse ready features, premium prestige and reasonable price tag.
The first great thing about this guitar is its amazing look. It has a Paulownia body with the metallic blue finish and a bolt-on construction. It comes with a dean vintage tremolo bridge which works quite well compared to others. One more advantage of this product is its cost. It is one of the most affordable electric guitars out there. It has a three-way toggle dual dean humbuckers which give you great volume and tone controls.
Phasers like the popular DOD-Phasor 201 are a perfect example of what a solid phaser pedal should sound like. Modern designs allow you to control many aspects of this effect, which makes them pretty versatile and suitable for most genres of music. Guitar players like Van Halen heavily rely on phasers to build their foundation, while some have even become famous due to their use of phasers. Phase shifters are generally very flexible and are among the most utilized modulation effects today.
The MC5 were the nexus where radical politics and proto-punk belligerence first came together. This dangerous mixture touched off an explosion that’s still rocking the world today. The group burst out of Detroit in the cataclysmic year of 1969, with its roots firmly planted in mid-Sixties garage rock, and mutated by injections of inner-city R&B and free-jazz mayhem.

I’ve been looking for a long time for information on what goes on inside a typical Strat-style 5-way switch, and this site helps me understand these switches a bit more. But I still have questions, though: 1)Why is it necessary to use jumpers from one lug to another? 2)As I understand it, a 5-way switch is 2 separate 4-lug switches wired together, each with 3 input lugs and presumably 1 output lug, OR are these lugs INPUT as well as OUTPUT lugs? (I get the impression that they are dedicated to either input or output, but looking at some wiring diagrams, it appears that inputs from pickups can come from either side of the switch.) 3) Is one side the INPUT side and the other the OUTPUT side, or are both sides of the switch mirror images of one another? In other words, must the signal from the pickup enter the switch at one side, and exit the switch at the other side? It seems I can only really understand how these switches work in terms of inputs (from the pickups) and outputs (to the output jack or volume pot). Without knowing whether a certain lug is acting as an input or an output, it can be hard to understand which way the signal is travelling.
James Burton, another famous Twin user, put it best: “If you can plug your guitar into an amp and make it sound good, that’s what it’s all about. The amp I really enjoy playing, especially when I’m traveling, is the Fender ’65 Twin Reverb. It’s got everything you need for live playing and it has great tone. That amp just works for me and it’s real trustworthy. When I travel on the road, I do use a little digital delay and maybe a little chorus, but I just like the sound of the guitar and playing something that I think people will appreciate and understand.”
Some guitarists find spectral overtone melodies inside sheets of feedback (see: Lou Reed’s Metal Machine Music, Sonic Youth), but British wunderkind James Blackshaw uncovers them in careful stacks of 12-string acoustic guitars and bright orchestrations. Minimal in his attack and classical in his drama, Blackshaw bears the acoustic guitar torch in the 21st century, his pieces unfolding in slow, formal shifts until they beam like a burning light through stained glass.

Because driving the power valves this hard also means maximum volume, which can be difficult to manage in a small recording or rehearsal space, many solutions have emerged that in some way divert some of this power valve output from the speakers, and allow the player to generate power valve distortion without excessive volume. These include built-in or separate power attenuators and power-supply-based power attenuation, such as a VVR, or Variable Voltage Regulator to drop the voltage on the valves' plates, to increase distortion whilst lowering volume. Guitarists such as Eddie Van Halen have been known to use variacs before VVR technology was invented.[specify] Lower-power valve amps (such as a quarter-watt or less)[citation needed], speaker isolation cabinets, and low-efficiency guitar speakers are also used to tame the volume.
Electri6ity is frequently compared to Musiclab’s real electric guitar line as they came out around the same time, and while Musiclab delivers better quality in most aspects, you only have one guitar per VST - where Electri6ity has eight. However,  while Electri6ity will give you twice as many guitars for the price, Musiclab continues to update their Real line, now blowing Electri6ity out of the water.
Processors, on the other hand, comprise an entirely different water heating appliance filled with piscean vertebrates, as they tend not to need any of the dry sound, other than in a few specialist applications. As a rule, processors such as EQ and compression are connected only via track, bus or master insert points — at least until you have the necessary experience to understand why you might want to break the rules once in a while. Having got that off my chest, let's look at some specific effects (we'll look more closely at processors another time).
As a rule, you don't add much, if any, reverb to low-frequency sounds, such as bass guitar or kick drums. Where you need to add reverb to these sources, short ambient space emulations usually work better than big washy reverbs, which tend to make things sound muddy. Taking this a step further, you can also make a mix sound less congested by EQ'ing some low end out of your reverbs.
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: epiphone","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"category","prop11":"electric guitars","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category"}
‘Rockabilly’ was used to describe a mix of Rhythm and Blues and Hillbilly music (or as it was later known Country and Western music). The term ‘Hillbilly’ was a crude term used previously to describe music from rural towns and mountain ranges of the states, specifically the Appalachians. Rockabilly paved the way for Rock and Roll and with Elvis Presley’s influence over the masses, it was this that thrived in the years to come.
I bought mine used in 1989 in a mom and pop music store in the North GA mountains in Cumming GA and have loved it everysence I Know very little about it except that I would not trade it for a new one. The sustain in the body of the overtone note is fantastic and rare to find.I use d'Addario phosphorus bronze strings 11 - 52 and would not change anything about this guitar,fantastic!!! Thanks Victor
"I wanted my guitar to sound like Gene Krupa's drums," Dick Dale said, and the hyperpercussive style he invented for his jukebox wonders – including a juiced-up arrangement of the old Greek tune "Misirlou" – pioneered the sound of surf rock. Dale played as fast as possible, at max volume; Leo Fender once attempted to design an amp that wouldn't be destroyed by Dale's sheer loudness. "His arrangements were really complex, really unruly," said Rush's Alex Lifeson. "It was all staccato strumming reverb, but with a reverb that just sounded so cool."
Treble is really a form of gain boost that must be considered while gain-staging our signal path. With good tone, a note should ring like a bell, not slaughter like a machete, and that is accomplished by shaving some attack off the waveform and rounding off the frequency response. A bit off rollback on the tone knob takes you into the ballpark, along with your amp settings (I have a dedicated treble-cut on my AC30 that is necessary to tame my telecaster). Once I am in the ballpark, I use the volume knob to fine tune, and personally I tend to let it be from there, relying on a gain-boost pedal to lift my sound when necessary without altering the tone.
The classical guitar repertoire also includes modern contemporary works – sometimes termed "New Music" – such as Elliott Carter's Changes,[17] Cristóbal Halffter's Codex I,[18] Luciano Berio's Sequenza XI,[19] Maurizio Pisati's Sette Studi,[20] Maurice Ohana's Si Le Jour Paraît,[21] Sylvano Bussotti's Rara (eco sierologico),[22] Ernst Krenek's Suite für Guitarre allein, Op. 164,[23] Franco Donatoni's Algo: Due pezzi per chitarra,[24] etc.
In 1956, Albert King (real name Albert Nelson) had moved to St Louis Missouri and his soulful blues performances were becoming very popular in their own right. He changed his surname to King on account of B.B King’s success with “Three O’Clock Blues‘. By 1967, the title track of his album ‘Born Under a Bad Sign‘ became his most popular and influential release.
Pickups and body styles are just scratching the surface when it comes to guitar features. No matter how overwhelming things may seem, though, if you’re only a novice or hobbyist there’s no need in fretting (get it?) over every single feature. Instead, look to the features we mentioned and go from there based on what type of music you want to play. If you’re a big blues and classic rock guy, powerful, full sound is necessary: you’ll likely want a semi-hollow or solid body guitar with humbuckers or P90s. Want to play old school country or folk? Check out hollow bodies. Are you a fan of alternative and punk? Consider a thin solid body with single coil pickups.
Great pedal! It is small, but is very sturdy and the design looks great. Each effect sounds great and the controls are easy to use. I would put each effect in this pedal up against any single effects pedal that I currently have and this multi-effect was cheaper than all of those. I play a lot of genres from country, classic rock, and metal and these effects can get you the tones you need for each! I am thoroughly impressed.
I like...So fun...I am a big fan of the call of duty games - this one is a step above my son loves it and I do to but he is a lot better at it than I am - it is a challange for someone new to playstation...Well first starters died about ten times just beginning in campaign and yea even though I have it on regular mode it still is a challenge for me signs of I'm getting to old for this lol but there snippers on story mode when you concentrate it slows down all the enemies but give it a shot your self I like it

The JEM70V is a Steve Vai signature model based on early JEMs he helped create. It comes with 3 different DiMarzio Evolution pickups that were handpicked by Steve Vai himself to give him the various tones that he needs for his expressive solo work, and intricate rhythm textures. The body is crafted from basswood, while the low profile 5-pc Maple/Walnut and 24-fret, 25.5" scale length rosewood fingerboard provide the fast playability expected of the brand. Other features include the Edge tremolo, 1.69" nut width, tree of life inlay, and it comes wrapped in Seafoam green finish.


I see some people using an A/B box straight from their guitar and then I suppose into two separate chains for 2 separate amps...is this a preferred method? I use my mormorley ab at the end and share my chain with both amps. Vox AC4-Marshall DSL...I have been contemplating running two separate chains...I'm fairly new to effects so I've just been toying around. Currently this my chain Guitar-Fulltone OCD-MetalPedals Dirty B*tch-Mesa Throttle Box- MXR 6 band EQ- EHX Small Clone-EHX Small Stone- Catalinbread Montavillian Echo- Visual Sounds Delay- TC Electronic Trinity 2 Reverb- Morley A/B/Y to Amps
And how does adding a pedal, basically one more optional pre-amplification stage that you can turn on or off at your leisure, make somebody less “real”? Imagine some old-school guy is just using guitar to a (insert amp brand)? Great! I love them too. Which one? Ah, nice amp! Did they know that amp has one more gain stage than that amp over there? If I plug into that one while they play theirs, did I make them less real or genuine, or did I become SUPER-real? Are they going to start fading like Marty McFly when the outcome is in doubt at the end of Back To The Future? Will they spring back to life and start playing “Earth Angel” properly once I unplug?

Octave ('Other' category): This effect really surprised me because it tracks well, but inserting the compressor before the Octave plug-in improves the tracking even further. Distorting the post‑octave sound with the AmpSimulator gives a big distortion sound, even with only the Octave 1 level turned up. If you want more of a brontosaurus guitar, turn up Octave 2 as well. In general, I like to leave a fair amount of direct sound in the output mix. You can just as easily go in a cleaner direction by using only the Octave 1 output, and bypassing the AmpSimulator. Select the neck pickup on your guitar, pull back a bit on the tone, and you'll hear a sound that recalls jazz great Wes Montgomery.


From an appearance perspective, at least, the most important aspect of the guitar is the body’s finish. The finish of most electric guitars is either a nitrocellulose lacquer, a polyester, or a polyurethane. Nitrocellulose, for the unfamiliar, is highly flammable and also known as gun cotton. It is obtained by the nitration of cellulose, an important structural component of plants. In guitar coatings, nitrocellulose is blended with other compounds and organic solvents to create a lacquer. The solvents evaporate as the lacquer dries.
Mahogany is a durable wood, often described as dense and that is used in the construction of guitars. The main advantage of purchasing an instrument made from this material is the fact that it highlights the unit’s bass and midrange. Therefore, if you are into mellower tones, this is the material that you should pay attention to. The resulting guitars made from this material are usually brown.

There is competition for Guitar Tricks and this is a good thing, as this makes sure that they have to keep improving. Prior to starting with Guitar Tricks I bought some lessons from True Fire. While the lessons were good and very well presented they needed to be downloaded onto a PC and could only be played in a special player program. TrueFire also offer an online service that includes group and one-on-one lessons.  Another alternative worth checking out is JamPlay. JamPlay has been continually gaining ground on Guitar Tricks and is worth while checking out. They do not have a free trial period, but you can get started with a very low amount for the first month and they also have some free lessons. Another option is a fairly new program called Infinite Guitar. They seem to be doing a rather good job too and also offer some free lessons.
New York City native Joe Charupakorn is a guitarist, author, and editor. He has interviewed the world’s biggest guitar icons including Steve Vai, Joe Satriani, Yngwie Malmsteen, Carlos Santana, Neal Schon, and Dave Davies, among many others, for Premier Guitar. Additionally, he has written over 20 instructional books for Hal Leonard Corporation. His books are available worldwide and have been translated into many languages. Visit him on the web at joecharupakorn.com.
The Marshall JMP Super Bass is a 100 watt amp. Lemmy, bassist/lead singer of Motörhead, used numerous of these amps to drive cabinets with four 12" speakers and others with four 15" speakers. His amps were labelled named “Killer,” “No Remorse,” and “Murder One".[5] The Peavey Mark IV is a large, solid-state amp providing 300 watts at 2 ohms; the Mark IV was known for its affordable price and its reliability.[6]

{"eVar4":"shop: shopbybrand","eVar5":"shop: shopbybrand: harmony","pageName":"[gc] shop by brand: harmony","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop by brand: harmony","prop1":"[gc] shop by brand: harmony","prop17":"sort by","evar51":"default: united states","prop10":"brands","prop11":"harmony","prop5":"[gc] shop by brand: harmony","prop6":"[gc] shop by brand: harmony","prop3":"[gc] shop by brand: harmony","prop4":"[gc] shop by brand: harmony","channel":"[gc] shop by brand","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] site section"}

Slot Peghead vs. Solid Peghead (steel string models): Most models converted from a 12 fret slot peghead to a 14 fret solid peghead around 1934 (except the OM series, which went 14 fret in 1929/1930 and the style 17 and 18 models which were available in 14 fret style in 1932). Basically if the guitar has a 14 fret neck, it will have a solid peghead. If it has a 12 fret neck, it will have a slot peghead. Note there were some post-WW2 gut string and classical models (i.e. 0-16NY) and some post-WW2 special order steel string guitars (i.e. 1967-1993 D-18S) which always have a slotted peghead.
The thoughtful design and close-tolerance machining of the mechanical components of most electric guitars enables them to be set-up and adjusted with great precision. But it is important to make these adjustments in the correct order- Neck-Nut-Bridge saddles. Making fine tune adjustment to any of these elements without reference to the others, or out of this order, will prevent a guitar's true potential from being realized.
It's interesting how one of the biggest brands in guitar amplification was built by a drummer! The story goes that professional drummer Jim Marshall was inspired by Pete Townshend, Ritchie Blackmore, and Big Jim Sullivan to develop a louder and better sounding amp. And he went about it by looking at a popular American amp design (i.e. Fender Bassman) and finding ways of how to improve it. After many prototypes, Jim and his team eventually came up with an amp that had their own "Marshall sound", this amp inherited the JTM label, an abbreviation of Jim's and his son Terry's names. The rest as they say is history, with Marshall being one of the most familiar amplifier brands, even to none musicians. Their brand is still the amp of choice for a long list of virtuoso guitarists, including Jimi Hendrix, Jeff Beck, Eric Clapton, Jimmy Page, Slash just to name a few. While their vintage and professional level amplifiers are still very much in demand, the company is not doing as great in the entry level to mid-tier market - which really is the bulk of where sales and reviews of come from. Still, their fans gave them enough good feedback to make it to this list, thanks to the improvements they are making to their entry level line of amps.
An acoustic guitar suited to bluesy rhythms. Has quite alot of fret rattle with the high velocities but also a certain amount of mid to high frequencies which helps to give it its own place in a mix. Presets include a standard mapped guitar, a fake twelve string (octave harmonies on each key) and split voices of muted fifths at one end and solo guitar at the other end of the keyboard (for quickly creating tunes and ideas). There are other banks of the same presets except with long releases (for sustained notes), chorus and/or reverb added to give the different variations. The amount of reverb can be altered with cc12 and the amount of chorus can be altered with cc13. Reverb and chorus has to be enabled on your soundfont player to use them.
Go to the blues and jazz though and things change. Listen to the guitars. Warm, mellow, beefy, thick, with tons of butter. And those guitar sounds are mostly clean or overdriven (not distorted as with a distortion pedal). Using the neck pickup works well for this, but in addition to that, guitarists roll off the tone knob to cut more of the treble to warm up the tone and make it blend with the rest of the music. It also keeps the tone beefy and thick so the soloist can cut through the mix but without sounding as harsh like a rock player. Don’t get it wrong though, some blues and jazz tones will require trebley tones, but the guitarist will use the tone knob to change his tone instantly without having to change his amp settings for each movement or song, especially when improvisations and long instrumentals are involved.
Excellent information. There is so much more to discuss on this topic. I built an Explorer shaped guitar with Strat hardware and humbucking pickups. I love the dive bombing note bends and the fat sound of humbucking pickups. I used Koa for the body and the neck came from a '70's Hagstrom electric. REALLY, thin neck. Read about guitars. See what artists like to play and why. Then fit it to your needs / wants. Brian May's Red Special uses wiring techniques I never heard or thought of. And he and his Dad made that guitar. Les Paul invented the guitar with the same name. Read about him and what he wanted. The ideas are out there to expand on. My Les Paul has 2 volume controls and a common Bass and Treble control. Different way of thinking. And it works for me.

The #1 cause of fret wear is the fretting hand pressure exerted by the player.  I have some clients that grip very tightly and wear frets quickly (Rob Fahey), and some that grip very lightly and take forever to exhibit significant wear (Jasan Stepp, Dog Fashion Disco/PolkaDot Cadaver).  Fret material hardness, string hardness and frequency of use all contribute to wear as well, but hand pressure is still the leading cause since frets do not wear themselves out.  Technique is different for every player, unique and personal and habits can be hard to change.  Just like brakes in a car, how hard and how much something is driven directly impacts wear and longevity.  Please see the refrets page for further thoughts on this topic.

Companion to the TG-64 was the TB-64 bass. This was virtually identical to the guitar – including the three pickups and monkey grip – except it was a bass, so it had no vibrato. Two other basses debuted in ’64, the NB-1 and NB-4. These were basically the same guitar as the TB-64 except they did not have the handle cutout in the body. The NB-1 had a single pickup and the NB-4 had two.
Dexter Holland (b. 1965) is the rhythm guitarist of punk rock band The Offspring and has played Ibanez guitars for most of the band's existence. He currently uses a custom diamond plate RG with a custom Jägermeister logo on the twelfth fret, as well as DiMarzio Super Distortion pickups, though he used to use a brown and green custom RG and has been seen with a custom Purple RG.

It's amazing how this relatively new company, which officially started in 2007, is now playing with the big boys. Blackstar has a pretty straightforward claim to fame, and that is to provide premium quality high-gain tone in the price ranges that they enter into. And judging from the very positive response of rockers and metal heads, they are doing their job really well. As usual, artist endorsements play a big role, and Blackstar has big name backers like Neal Schon from Journey, Richie Sambora, Ted Nugent and Sammy Hagar to name a few, along with a long list of up and coming guitarists from rock and metal bands. While they still excel in providing high-gain tones, Blackstar amps also offer versatile overdrive and distortion flavors, thanks to the company's innovative ISF (Infinite Shape Feature) technology, which lets you change the tone of your amp from American to UK flavors with just one knob.

The chorus effect sounds like a lush underwater soundscape that is created by doubling your guitar signal and slightly shifting the second one out of time and pitch with the original.  This effect can be very subtle, which sounds as if you’re playing out of two different amps separated in space, or highly modulated to sound as if two different players are playing the same part at the same time.
11. Yamaha THR10 ($299): Another compact yet mighty combo amp, the THR10 boasts a mid-century-modern design with a variety of onboard effects and amp emulation options. This amp uses Virtual Circuitry Modeling (TCM) technology, which creates realistic and pristine tone. When plugging in your bass or acoustic guitars, you can even bypass the modeling section. One of the most convenient functions is the ability for the amp to run on a supplied AC adaptor or battery power for ultimate portability in your individual practice scenario. And it even includes Steinberg’s Cubase AI recording software so it’s plug-and-play right out the box!
As a musician for 50 years and a custom builder for 30 years I definitely believe that wood choice has an effect on the tone and sound characteristics of an electric guitar. In my younger years as a cabinet maker, I was helping install a large church pipe organ (Cassavan I believe). The installer from Montreal and I had some discussions about wood and specifically wood properties best for certain applications. He told me that they used poplar for the spacers between the organ pipes because as a good tone wood, sound did not bleed from one pipe to another which is very important with pipe organs. They are the oldest and I believe the largest pipe organ manufacturer in the world and have done a lot of trial and error in this area according to the installer as to what wood works best. I happen to agree with them and agree that poplar is an excellent tone wood and works very well in guitars. Jackson guitars use poplar in there guitar bodies and is a great sounding tone wood. I use it a lot in my custom guitar because of the nice tone it produces.
There aren’t a lot of professional reviews of inexpensive amps, but James at Guitar Verdict raved about the Champion 20, saying, “For an amp of this price, the Fender Champion 20 watt offers a massive amount of value,” and calling it “a hard to beat offering.” At last count it had earned an average of 4.6 out of 5 stars in 595 Amazon user reviews and earned an A for review integrity from FakeSpot.

From the 1860s on, fan bracing became standard in Europe. Martin and other American builders including Washburn and others since forgotten (Schmidt & Maul, Stumcke, Tilton) used X-bracing instead.[3] The sound of X-bracing may be considered less delicate with gut strings, but it prepared the American guitar for steel strings, which emerged in the first quarter of the 20th century.

In nature, reverb is an extremely fast series of echoes that reduce in volume over time.  Depending on the size of the environment, the number of repeats and the timing at which they occur will change.  Digital reverb pedals are very good at replicating the differing types.  Basically, you can take small tiled bathroom and the Grand Canyon (and everything in between) with you to your gigs.
Reverb sits at the other end of the tonal kaleidoscope, serving usually to add warmth and depth to a clean tone. Practically speaking, reverb simulates the sound of your guitar being played in a larger physical space. Imagine shouting at the top of your voice in a cloakroom. Then imagine doing the same thing in a church and you’re somewhere near there. Ok, that’s an extreme example, but approximating the sound as it reverberates around is quite a seductive thing when applied to a guitar. There are plenty of good examples of it being used to add a bit of life to an otherwise sterile clean tone.
The Streamliner concept is simple: to create more affordable Gretsch guitars without losing their specific DNA. Two new Broad'Tron humbuckers are controlled in classic Gretsch style by a three-way toggle selector switch on the bass side shoulder, a master volume on the treble side horn, and then a trio of controls by the treble-side f-hole for individual-pickup volume and master tone. The G2622's construction gives a different response and resonance to other new releases from Gretsch and, with these pickups, moves further from the Gretsch sound. And while its construction gives it a more solid, or at least ES-335, character, it's a little more airy and less punchy with a softer, squashier tonality. The beefier pickups certainly don't nail a classic Gretsch tonality - although if that's what you want, the full-size pickups are easy to replace - but they do broaden the sonic potential, especially for more gained styles, while staying close to the classic iconography. If you want a great-value semi-hollow, this is among the best electric guitars for under $500.
Our list of best electric guitar brands will remain incomplete if we do not add Schecter in it. Schecter Guitar Research is a firm that evolved from a startup into a guitar giant during the recent years. Aimed mainly at the heavy metal side, Schecter produces several guitars that metal players look. However, players from all genres will find something of their wish at Schecter as it touches every side of this domain. Created with the utmost care, delicacy, and artisanship, these guitars exhibit the most amazing and high-end features that suffice to surpass most expensive brands in the market today.

"Bring up one mic at a time and get it to optimum level on your board. To check that they're all in phase, make sure the signal is adding and not subtracting as you add in the other mics. If not... reverse the phase. Then start to put up each mic, one at a time... as you move the faders back and forth, you'll hear the greatest EQ, because of the phase relationship... Then if you flip the phase on one of the mics, you can really have some fun — it'll act like a filter."
The first trick is the most obvious one: to double a crunch or heavily distorted guitar with a clean one. By sub-mixing a clean sound, you will be able to retain some precision, which is no minor detail considering that distortion has the annoying tendency of blurring sound. For this trick to be as transparent as possible, the crunch and clean performances must be as similar as can be. That being said, if you have a hard time getting that perfection, you can always "cheat": be it by editing the clean sound to make it match the original performance or simply doing some reamping with the first take, as discussed previously. In both cases the trick ought to work wonders because the clean take is only meant to be "felt" but not distinctively heard by the listener.
Electric guitars vary by type. Some are designed for beginners, while others are customized for professional guitar players. Most of the major electric guitar brands are available in a variety of different styles, each designed to best suit a customers' specific playing needs. The most popular electric guitars have great rock sounds and the best bodies. On electric guitars, strings affect the sounds too. Ease and sound are certainly big factors to consider when choosing a new electric guitar.
It's the neat switching that makes this very classic-looking Tele act a little differently. All the standard Tele pickup selections - bridge, bridge and middle (in parallel) and neck - are in place, but it's a four-way switch, as opposed to the standard three-way; the additional selection provides us with both pickups in series for a bigger, louder and more humbucker-like 'secret' sound. The volume control has the S1 push switch in the top of the control knob: pushed down, the parallel and series-combined pickup selections are out-of- phase, giving three additional sounds over the standard Tele. The Baja sticks relatively close, of course, to the classic 60s Tele recipe. The rosewood 'board and alder body just seem to give that lovely smoothness to the high end that will make it less ear-wearing, especially if you're swapping over from an older-style humbucking Gibson. The standard mix is typically classic, wider than a Strat's but still nicely textured; the neck pickup here sounds a little fuller than some older readers or vintage Fender electric guitar owners will remember.
If you are considering a traveler or mini guitar, be sure to read reviews of people who own models that range between $40 - $500, because you will find various reasons to stay away from some of the cheaper models that are under$150.  Some of these guitars that are made that cheaply are not much better than toys in quality, sound and crafstmanship, and at this model and price range, you will get what you pay for.  By investing an extra $100 - $200, you can find some fine travelers and minis that will more than accomplish the job, and in fact, some professionals choose certain travelers and minis over others for playability, quality, performance and recording reasons.

Many great players (including Hendrix) placed the wah before distortion... though many of the modern rock guys place it after distortion to make the frequency sweep cleaner. Personally, I prefer the Wah before distortion, but it's personal taste really. Depends a bit on the pedal too - how wide the frequency notch is and what frequency range it covers. I have my Wah on a G-Lab True Bypass Wah Pad, which I think is a great product... I have a few Wahs that I like, the Keeley Mod Vox Wah and the RMC3 are probably my first choices to try out.


This is a right handed 2018 Gibson Custom Shop Explorer, Extra/Elbow Cut, with a heavy aged relicing, Natural Finish, Gold plated Nickel hardware. This model is patterned after the 1958 Explorer owned by Eric Clapton. It is brand new with OHSC, COA, and all paperwork/tags. The weight is light at only 7 lbs, 12 oz. This is only one of a limited run of 5 in the Natural Finish. I also have the same guitar in Cherry finish, one of only 5 in the Cherry finish.

You have all the control you need over your effects and you can use all three at the same time, too – ideal for those who like to create big walls of sound. The delay features a tap tempo control, whilst the FX loop connectivity allows you to hook up any other effects pedals you might have before the delay, which ensures the tonal qualities of those pedals are intact.


Compressors – The role of these pedals is to lift up quiet sounds and rein in loud sounds, compressing the dynamic range of your signal – that is, the difference between the quietest and loudest sounds. They work wonders for songs with a blend of quiet and loud parts, since they let you play hard without busting eardrums, and the soft sections won’t be drowned out by ringing ears. Compressors also have the nice side effect of increasing sustain, letting your notes sound out longer before dropping off.
So you’re thinking about building an electric guitar. Well, it’s a very rewarding experience when it’s done right, and you have the ultimate freedom to make it whatever you want. On top of that, it can be a money saving alternative to the hefty price of a good instrument, if you’re willing to invest your time. Or if you’re just planning on undertaking a fun project, it can certainly fit that bill too.
PRS really took off back in the ‘90s when it seemed just about everyone had swapped out their Les Paul for a PRS. Eventually they capitalized on this trend and made the PRS more accessible by introducing the SE line of lower-budget guitars. But these aren’t beginner’s guitars. Even though they cost less than a standard PRS, they’re still high-quality instruments.
This is a very cool goldtop Vox SDC 33. Ultra slim body and neck makes playing extremely smooth and comfortable. Coaxe pickups provide a unique array of tones. Has some natural wear from normal use, like the buckle rash and a chip on the neck finish shown in the pictures. Overall a very clean and well playing guitar with a unique look and sound. Contact us with any questions! Thanks, Fondren Guitars
In 1952 the pickup selection circuit was modified by Fender to incorporate a real tone control. Between 1953 and 1967 the neck could be selected alone with a pre-set bassy sound and no tone control, in the middle switch the neck could be selected alone with the tone control and finally the bridge could be selected with the tone control. Although this provided the player with a proper tone control, this assembly did away with any sort of pickup combination. Eventually from late 1967 Fender again modified the circuit for the final time to give the Telecaster a more traditional twin pickup switching system: neck pickup alone with tone control in the first position, both pickups together with the tone control in the middle position and in the third position the bridge pickup alone with the tone control.[2]

Loop pedals — or loop stations as they're often called — have exploded in popularity in recent years as more and more players have embraced the ability to build multiple parts and loops during gigs and practice sessions. With popular options like the TC Electronic Ditto Looper, guitarists can lay down a basic chord progression while soloing on top. Loop stations are also a popular option for vocalists who can use these devices to build harmonies or deploy creative vocal effects. Whether you're in need of a basic option like the Electro-Harmonix 360 Looper or a more elaborate solution like the Boss RC-505, there's never been a better time to get into the world of looping.
×