Kaman began producing guitars in 1966, and Charles went on the road to promote his new creation. His first stop was a visit to his old stomping grounds, Washington, D.C., where he showed his guitar to jazz guitar great Charlie Byrd. Byrd was impressed and felt the guitar – which was quite loud – had considerable potential. He later remarked that the guitar “deserved an ovation,” thus providing the guitars with a name.
Although it is well known for its guitars, Gibson's largest business is in fact electronics.[citation needed] Gibson offers consumer audio equipment devices through its subsidiaries Gibson Innovations (Philips brand), Onkyo Corporation (Onkyo and Pioneer brands), TEAC Corporation (Teac and Esoteric brands), Cerwin Vega and Stanton,[6] as well as professional audio equipment from KRK Systems and TEAC Corporation/TASCAM.
But the avant-garde din of Velvet Underground rave-ups seemed a genteel curtain raiser compared with the full-bore cacophony of Lou’s 1975 solo opus Metal Machine Music. The noise-guitar side of Lou’s legacy set the stage for cutting-edge genres like industrial, art damage, dream pop, grunge and present-day noise exponents, like Wolf Eyes and Yellow Swans.
A tabletop unit is a type of multi-effects device that sits on a desk and is controlled manually. One such example is the Pod guitar amplifier modeler. Digital effects designed for DJs are often sold in tabletop models, so that the units can be placed alongside a DJ mixer, turntables and CD scratching gear.[17] For a DJ, a pedal located on the floor would not be practical because she/he would find it hard to adjust the knobs.
Guitar signals cutting out is a very common symptom of a simply wiring problem. Usually when your guitar cuts out, it means that you have a loose solder somewhere. Your guitar will sound fine when the solder connection is joined, but your guitar will cut out when the loose wire disconnects for the lug. Broken solder joints are common on electric guitars especially when your output jack becomes loose and rotates in the pocket. That is why it is extremely important to keep your output jack tight and secure at all times. If your output jack is loose and rotates, it will probably break the wiring connections inside the guitar. Luckly, loose connections are easy to fix. The only problem is trying to find them.
Depending on whether you play rhythm or lead guitar, you will want more or less treble cut. One of the secrets to a two guitar band lies in the tonal differences achieved between the guitars that stop them from bleeding together. Part of this is inherent in the different instruments and amps used by the two guitarists (humbucker vs single-coil pckups being the greatest differentiator imo, as well as discerning use of the pick-up selector switch), but the contrast must also be attended to on the fly, and here the tone knob, along with the useful volume knob help the two guitarists from stepping on each other’s tonal feet while mixing their notes together.
Here we have a well preserved vintage Hohner HW600n HW for Hohner Western Acoustic Dreadnought Martin D35 Style acoustic guitar. with a gorgeously grained THREE Piece Mahogany back and sides WoW its really a beauty. Workmanship Fit and finish quality is excellent this guitar is stunning, previously set up and is Great sounding in near mint like condition its from the late 80’s early 90’s D35 Look alike, Spruce top with Mahogany Neck and some of the absolutely highest grade Mahogany your going to see its flamed and figured and has fire and looks as if it could be Koa but listed as Mahogany at any rate this is one of the nicest models Hohner in this era truly a stunner,,, its in top structural shape as well its neck angle is excellent at 1-11/16ths at the nut its medium profile neck is very easily played and is a convertible c shape… We were impressed with her sound to with nice volume and a mature sounding tone. We think you’ll like this beautiful Vintage Hohner as well we believe this to be late 1980’s to early 90’s made in Korea and would fool any made in Japan fan for its fit and finish workmanship this is a good vintage guitar in its own right… no cracks no repairs no issues no excuses someone is going to have a smile on their face. any questions or to buy this guitar contact Joe at: JVGuitars@gmail.com .

Welcome to KayBassGuitar.com.  We're a the online Kay Vintage Reissue web site of Rock N Roll Vintage Inc., a Chicago based internationally known vintage guitar dealer.  Kay currently offers the "Street Series" and a "USA Recording Studio" lines.  Kay plans to offer reissues of 12 popular models including the Barney Kessel and the Jazz guitar and bass lines.   The Street Series are authentic reproductions of Classic Kay guitars and basses.   The Recording studio series will offer models with exceptional hand built custom shop quality.  We offer the complete line of Kay Vintage Reissue Basses and Guitars.   These Kay reissue guitars and basses look amazing and play even better.  Currently the Kay K161V Thin Twin and K775V Jazz II guitars and K162V Pro and K5970V Jazz Special basses are available.


A partial PA is harder to define, but it's essentially any PA system that doesn't have the capacity to mic your whole band. More often than not, in these situations, mics end up on the kick drum and snare drum for the reasons outlined above. In this case, it does help to have a little extra juice in your amplifier, but try to keep it tamed, nonetheless.
In our testing, the Fender Champion 20 was the only amp that offered a wide variety of amplifier sounds and special effects while also keeping them all easy to access. Beginners can get a great sound easily and experiment with different effects without having to invest in separate effects pedals. Experienced players can get most of the sounds they want with nothing more than a guitar, an amp, and a cable.
From rock to jazz or folk to metal, what separates the great guitarists from the rest is their mastery of the skills taught in this program. From basics like chords and scales to nuances like improvisation techniques, form, control, and inflexion, this certificate program will take your guitar playing to the next level. Few accomplished guitarists have reached their peak alone, and Berklee’s faculty is unparalleled when it comes to delivering the personalized instruction and feedback that will help you turn the fretboard into a playground packed with unlimited possibilities.
• Guitar : ELECTRIC SUNBURST captures the sound of a classic guitar, chosen with its rich, warm and versatile sound. The continuous signal path has been retained throughout, including high-quality cables, vintage tube preamps and high-resolution transducers to ensure that every nuance of this legendary instrument was accurately fixed. Since the string holder and neck were recorded separately, you can fully control the balance of the mix. Moreover, a condenser microphone was installed above the strings to capture subtle sound nuances and add punch and realism.
Guitars. Having all your guitars set up properly is an obvious essential for dialing in good tone. I like low-ish action, and for low action to work, I need to set my guitar necks to have just a bit of relief so the strings won’t buzz and rattle, and in turn choke the tone. I’m always checking the neck relief on my guitars and adjusting the truss rod accordingly.

It is also important to consider the maximum number of effects that can run simultaneously, which are usually based on effect group types or "blocks". This means that you usually can only have one modulation, one reverb, one drive etc in a preset. Advanced processors allow for more freedom which include combining same type pedals, series/parallel routing, pre-post amplifier routing and many more. While they allow for more ways to craft your tones, these processors also require more tweaking time and are usually more expensive.
CP = manufactured by ???; some speculation is that CP stands for Cort Plant or that models with this designation were made by a partnership of Cort and Peerless or perhaps even that it indicates production at Cort's Indonesian plant which is known as Cort PT (although this last possibility seems highly unlikely since the instruments are marked as "Made in Korea"). (2003–2008)

Early Teisco instruments were primarily electric Hawaiian guitars and accompanying amps, although the company quickly got into electric Spanish guitars, too. Little information is available on these earliest Japanese Teiscos. Teisco guitars from most of the ’50s were clearly inspired by Gibson; presumably this was true from the very beginning. We’d welcome any information on these early Teisco guitars and amps, including photos and photocopies of catalogs or ads, from our Japanese readers, if they can provide them.

Play a classic 6120 or Duo Jet and it can seem a bit, well, old-fashioned. A growing number of players desire the brand’s looks, sound and unmatched vibe, but also want something a tad more versatile and user-friendly. Enter this latest Players Edition model with its neck set lower into the body for improved access, higher-output Filter’Tron-style humbucking pickup (Full’Trons) and a modernised Bigsby vibrato where through-stringing replaces the notorious ‘hooking the ball-end over a peg’ system that scuppered any chance of a quick change. Mate these modern tweaks with another recent innovation (for Gretsch, at any rate), the Centre Block range, and you have a guitar ready to compete with anything out there - in virtually any style.
A more successful early electric was the Ro-Pat-In "Frying Pan" guitar. This was played lap-steel style, and was the earliest I know of that uses something close to the magnetic pickups as they exist in modern guitars. This was conceptualized by George Beauchamp in 1931... he played Hawaiian style, thus the lap steel design. He met Adolph Rickenbacker and together the two worked out the details of the pickup system, and put this into production in 1932... the company name was eventually changed to "Rickenbacher".
The first subject I concentrated on is (you guessed it) recording electric guitars. What became immediately apparent was that there was a huge range of different techniques being used, and also that there were strong differences of opinion between different professionals, which left the question 'who do I believe?' The only way I could answer that question was to put the different techniques into practice in the studio, and then A/B them to sort the sheep from the goats.
i really liked it! especially since it goes over standard musical notation, which hasn't been considered a conerstone for electric guitar players, but i think, like the author says "it a skill you'll never regret learning". the reason it didn't get 5 stars is because the book states that it will start from zero as for standard musical notation, but it doesn't, it assumes a bit of knowledge and it advances at a perfect rate for some who has already a notion of standard musical notation, but not for someone who doesn't have a clue a buys this book to go from zero-to-master such ability.
Unfortunately, no reference materials were available for this early period, so we’ll make some educated guesses. Based on the evidence of the logo on the 1968 amplifier, we suspect Univox guitars with the plastic logo debuted at about the same time. By 1970, Univox was employing decal logos on some models, further corroborating this conclusion. If this assumption is correct, it would suggest that among the first Univox guitar was the Mosrite copy known later as the Hi Flyer, debuting in around 1968. This would be consistent with the evolution of “copies” in Japan. As the ’60s progressed, the Japanese were getting closer and closer to the idea of copying, producing guitars similar to their competitors, such as Italian EKOs and Burns Bisons, etc., finally imitating American Mosrite guitars in around ’68. The Japanese affection for Mosrites was no surprise, since the band most associated with Semi Moseley’s guitars was the Ventures, who were enormously popular in Japan.
Correct bridge placement determines a guitar's intonation when playing fretted notes. The distance between the guitar nut and bridge is the scale length. Placing the bridge too close to the neck shortens scale length and makes fretted notes sharp. Moving the bridge too far from the neck increases scale length and creates flat fretted notes. No amount of tuning helps a guitar with a poorly positioned bridge. Any fretted note falls high or low of the desired pitch.
The SG Special by Epiphone is our hands down top pick. As you'll know by know, Epiphone is one of the best guitar manufactures in the business – so the quality of this guitar is absolutely amazing. Its epic red devilish double-cutaway design gives easy access to all 22 frets. It has a hard maple neck and a slim taper D-profile which ensures durability and rigidity. The fretboard is made of rosewood which makes it easy to learn to play. This guitar is all about that rock sound - it's equipped with two open-coil and noise-free humbucker pickups. The hardware is carved from nickel and is available in two dazzling finishes, cherry, and ebony.
We ship exclusively with FedEx / Signature Required and only ship to listed address on the item order page. Tracking will be provided and uploaded to Reverb once shipping is processed. We strive to ship ASAP however processing can take 1 to 2 business days from the time payment has cleared. FedEx does not ship on Saturdays or ship to PO Boxes. Shipping Fee's are subject to change if costs are much higher than expected.

The first burst of interest in Explorer-style guitars in the 1970s, led by players such as Rick Derringer and Sammy Hagar, was followed by a hiatus at the end of the decade when guitarists followed an Alembic-style lead. However, natural-finished neck-through guitars with sophisticated electronics didn’t cut it with the heavy metal bands that became more popular in the early 1980s with the New Wave of British Heavy Metal and the subsequent American response, chiefly out of Los Angeles. Poofy hair and skin-tight spandex begged for guitars with in-your-face style. The radical Explorer shape was perfect for making the right kind of personal stage statement. Manufacturers jumped on the bandwagon. Baby Deans, Ibanez, Aria, Cort… Even Gibson offered Explorers in cool custom graphics.


Thunders had the riffs to match the glam-trash group’s mascara. He took rock guitar and cooked it down to its essence, playing open chords and switchblade riffs that laid bare the amphetamine urgency behind the Dolls’ concise, catchy tunes. The Dolls had split up by the time punk rock got underway in New York and London, but their influence was profoundly felt on both shores.
Another clarification about brand names is in order. Teisco guitars can be found mainly bearing at least eight brand names: Teisco, Teisco Del Rey, Kingston, World Teisco, Silvertone, Kent, Kimberly and Heit Deluxe. Teisco was the name used mainly in Japan but also on a few occasions here in the United States. Most Teisco guitars were imported into the United States by Chicago’s W.M.I. Corporation � originally owned by guitar importing pioneer Jack Westheimer � bearing both the Teisco Del Rey and Kingston brand names. By the mid-’60s W.M.I. was providing Teiscos to Sears and Roebuck carrying the Silvertone moniker. I’m not sure the World Teisco brand ever got to the U.S.; my guess is that it was an export designation that went to other markets. Some of the early Kent guitars imported by New York’s Bugeleisen and Jacobson were purchased from Teisco. The distributors responsible for either the Kimberly or Heit Deluxe brand names remain a mystery at this time. It is possible that you may encounter other brand names on Teisco-made guitars sold through other distributors, but these will be in a minority. If you know of any other names, please let us know.
Amazing unit! I loved using my POD XT Live for years and wanted to upgrade. This unit totally exceeded my expectations. Sounds amazing and it's incredibly flexible for routing processing and effects chains. They built the hardware better and it's got a better set of pedal buttons too. Absolutely recommend! (Plus, they announced at NAMM that there will be more model packs, so that's great too!)
Pots generally come in two types: 500k or 250k. K refers to 1000 ohms and is a measure of resistance, which is the amount of resistance the signal from your pickup receives before being passed to your output. As a result, increasing or decreasing the amount of resistance your output receives via your volume pot affects the overall volume of your guitar.
The key feature that makes the GT-1000 stand out from the crowd is the inclusion of the ingenious AIRD (Augmented Impulse Response Dynamics) technology which ensures your effects respond correctly with the likes of tube amps and don’t muddy your sound. You can read more about the AIRD technology here, but in a nutshell, it ensures the dynamics of your unique amp are preserved. With other multi effects, you might find have to turn your amp emulations off if you want your effects to respond correctly to YOUR amp, but with the GT-1000 you won’t have to do that as you can select which type of amp you’re playing with and the pedal will respond correctly.
{"id": "H82691", "skuOrProductId": "H82691", "categoryId":"site1BAJ", "name":"Thunderbird Classic-IV PRO Electric Bass Guitar", "pageUrl":"/bass/epiphone-thunderbird-classic-iv-pro-electric-bass-guitar", "thumbnailUrl":"https://media.musiciansfriend.com/is/image/MMGS7/Thunderbird-Classic-IV-PRO-Electric-Bass-Guitar-Alpine-White/H82691000001000-00-120x120.jpg", "addToCartUrl":"/bass/epiphone-thunderbird-classic-iv-pro-electric-bass-guitar", "hasFeatures":"1", "isAccessory":"0", "message":"The Thunderbird IV was first introduced in 1963 and instantly became one of rock's most recognizable bass guitar designs. For almost five decades, the Thunderbird has powered artists as varied as Nikki Sixx, The Who, Kings of Leon, Cheap Trick, Lynyrd Skynyrd, Steely Dan and The Silversun Pickups. Turn on your radio and you'll hear a Thunderbird bass. Now, Epiphone takes all the vintage mojo of the original Thunderbird IV and sends it flying into the future with Gibson TB Plus humbuckers with ceramic magnets and all the 'Bird's original styling and features intact.

The Thunderbird IV was one of the most radical designs to come out of the Gibson and Epiphone Kalamazoo factory in the early '60s, thanks to legendary automotive designer Ray Dietrich, who was asked to put a new twist on solidbody guitars and basses. The sound of the Thunderbird IV was as cutting edge as its design and now the Thunderbird Classic-IV PRO returns with all of Epiphone's first-class quality and a lifetime guarantee, but without the hassles of owning (or hiding) a vintage instrument. Case sold separately.
", "value":"439.20", "priceMin":"439.20", "priceMax":"549.00", "priceSavingsMaxPrice":"0.00", "priceSavingsMaxPercent":"40", "inventory":"21", "brand":"Epiphone", "reviewStarImageUrl": "https://static.musiciansfriend.com/img/brand/mf/cmn/Sprit-Sm-Stars.png", "reviewStarRating":"4.5", "reviewStarRatingInteger":"9", "reviewHowManyReviews":"29", "usedOrNew":"used", "discontinued":"0", "onOrder":"0", "clearance":"0", "canBeSold":"1", "accessoryCategories":"site1LROBB,site1HBAL,site1LFML", "stickerText": "Top Rated", "checksum":"397377354900", "priceVisibility": "1"}

The effect also took Nashville by storm in the 70’s as well and was a favorite of Waylon Jennings’ music and others. What the effect does is mix the guitars signal with a slightly delayed reproduction of the signal. This delay shifts the waveform a few milliseconds thus producing the out of phase sound. It then uses a LFO (low frequency oscillator) to control the sweeping effect of the phaser. This pedal is key to the classic VH guitar sound!
I’m going to be doing a pickup upgrade in the next few months on a Strat-style HSS. I have an idea, maybe a crazy idea, about how I’d like to wire it but so far I have been unable to find any indication that it is even possible. This site seems like the best place to get an answer. The single coils in my guitar will be replaced with another set of single coils (Seymour Duncan SLS-1 lipsticks). The humbucker I plan on installing (DiMarzio Tone Zone) is capable of being coil-split, which I want to take advantage of BUT I would rather not install a push/pull pot. My wiring idea… Toggle Position: 1) Full Humbucker, 2) North coil only of humbucker for single coil performance, 3) middle coil only, 4) middle and neck, and 5) neck only. Is this even possible using the 5-position toggle switch I already have, or is there no way to do it besides using a push/pull pot or installing an additional mini-toggle?
Like Television not too long before them, Fugazi founders Ian MacKaye and Guy Picciotto engaged in a locomotive, dub-influenced dual-guitar shouting match. Though most of the talk around Fugazi inevitably leads back to their founding ethos, that way of thinking and operating permeated the music as well: Together, MacKaye and Picciotto were anti-frontmen, playing like a living, fire-breathing, two-pronged embodiment of democracy.
Most Heroic Moment: The simple, searing lines of 1990’s “Turnover.” D.B.
Guitar amplifier design uses a different approach than sound reinforcement system power amplifiers and home "hi-fi" stereo systems. Audio amplifiers generally are intended to accurately reproduce the source signal without adding unwanted tonal coloration (i.e., they have a flat frequency response) or unwanted distortion. In contrast, most guitar amplifiers provide tonal coloration and overdrive or distortion of various types. A common tonal coloration sought by guitarists is rolling off some of the high frequencies.
Now, for most players, deciding what should go where on a signal chain simply came through trial and error along with a good dose of common knowledge. And while a player’s signal chain should be his or her own, those of you out there new to creating a solid signal chain can benefit from some of the general 'rule of thumb' type of advice that can get you started in the right direction.

Another popular value pack comes courtesy of one of the greatest rock'n'roll guitarists of all time. For those who have an appetite for destruction, look no further than the Slash AFD Les Paul Guitar Outfit. Endorsed by the Guns N' Roses shredder himself, this pack comes with the killer AFD Special-II guitar that's equipped with new Ceramic Plus humbucking pickups, and a built-in Shadow pickup ring E-tuner. Additionally, this pack also contains a custom gig bag with the Slash "Snakepit" logo, Slash signature Dunlop Tortex picks, and much more.
Great playing and sounding bass. The Ibanez BTB series in a 'very playable' 4-string version. Huge tone is delivered via 2 active pickups that feature controls for volume, bass, midrange, treble and balance. We believe the pickups are actually made by Bartolini. 'Locking' 1/4 jack. Solid wood, natural finish body. Rosewood fingerboard on maple neck. Tuning is accomplished via quality, 'sealed' tuning machines. Rock solid and stays in tune. Set up great! Currently has 'nylon wound' strings for a softer 'jazz' tone. Frets show virtually no wear. Body finish has VERY little wear. Includes gig bag.
WoW Talk about nailing the essence of the Original by Gibson.... This is a well crafted Japanese Prime Lawsuit era Classic with the great looks and BIG fat TONE is what this old vintage Japanese script logo Alvarez J200 guitar has to over you today nearly 40 years ago and a true Japanese Vintage work of art really. Beautiful Headstock with Alvarez Script logo in mother of pearl inlay with crown as well is its original truss rod cover is striking.Overall The fit and finish is hard to beat the materials are superior grain looks as is fit and finish and she has stood the test of TIME. Minor Vintage checking seen on its top and only adds realism to its true vintage status no reduction from its appeal its very cool looking as you can see from its pictures even perhaps more beautiful than the 70]s Gibson from this same era this Alvarez is based on the early1960's era known to be the preferred vintage era to own amongst the Gibson aficionados This is a prime example and is overall GREAT with super easy low action we completely cleaned this instrument upon its arrival it was owned by a smoker and needed it but never abused luckily then we dressed the frets and polished the entire guitar and frets as a result it looks this amazing and I have seen every square inch and can tell you this is a very good example from my inspection while working on it. She plays really nice now, with very good volume and a rich vintage 40 year old Vintage Alvarez kind of tone I expect from a good J200... This guitar has that, No brakes no repairs non needed no reason this vintage Japanese Lawsuit J200 should easily play another 40 years with good care she's set up and playing Amazingly.... SUPER FUN to play Act quick our last Alvarez 5052 Script logo went pretty fast... She's here and available and in stock.... email Joe to buy it NOW: JVGuitars@gmail.com .
{"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: hohner","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","prop17":"sort by","evar51":"default: united states","prop10":"brands","prop11":"hohner","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
In 1979, there was a benefit for Amnesty International called “The Secret Policeman’s Ball”. Pete Townshend played acoustic versions of “Pinball Wizard”, “Drowned”, and (in a duet with classical guitarist John Williams) an astonishing version of “Won’t Get Fooled Again”. Unfortunately the soundtrack for that show has never been available in the CD and digital download era, but you can often spot these performances on YouTube. Highly recommended.
Hook, who covered the economics of running a nightclub in his 2009 book, “The Hacienda: How Not To Run a Club”, predicted: “The guitar companies are going to restructure and get smaller. The true artist in the company — the guy who builds a guitar by carving it out of a piece of wood hopefully will be the one that will be celebrated, not the middle management.”
I inherited a guitar and am looking for any information I can about it. It is a Kent model 533 Videocaster. I have no idea when they were made or what this one might be worth. It is a solid body, but I know next to nothing about guitars so I am not sure what other info might be needed. It needs to be tuned/serviced and possibly needs a little restoration, but otherwise it works and is not in horrible shape. Any info would be appreciated.

Gibson guitars are the produce of the Gibson Guitar Corporation which produces guitars and other musical instruments which sell under a variety of brand names. Gibson Guitar Corporation was founded in the year 1890 by Orville Gibson in USA. It is a mass producer of the Guitars and is the most widely used guitars in the world. Gibson guitars are exported all over the world and are considered as one of the best guitar brands in the world. Gibson Guitars actually are the giant guitar company which also owns other brands of guitars. Some of the popular brands which are owned by Gibson are Baldwin, Epiphone, Kramer, Maestro, Slingerlands etc.
Here we are proud to have in stock today is a Cool one she's pretty rare too its a real vintage guitar its actually 42year old in fact. This is a great old Vintage Goya Acoustic Dreadnought Guitar by CF Martin & company. This guitar was built in the early 1970s in Japan when Martin had thought that it was a good way to address the Japanese high quality lower priced Japanese guitars cutting into their bottom line so Martin commissioned Goya of Japan to build their competitive to the US line "import" line ( Japan because no other country at that time was building anything close to the high quality guitars like Japan was making " China , India, Twain was not even a consideration Japan was in another league obviously to those countries... so Goya was commissioned back in the day this pre dates Sigma Japan... This was built durring the time frame when the Japanes builders had some of the best quality woods available to them and were setting out to show the world what they could really do. This is a great example with both fine quality qoods used from the high grade mahogany to the solid spruce top to the rich dark Brazilian rosewood looking fingerboards they selected wow impressive work...Kept in great shape all these years 42 years see the pics it looks more like its 3 years old then 42... here today for a song we believe this example was built in Nagoya by the great Terada, that is pretty much the Custom shop builders in Japan they are responsible for the GB10 George Benson Ibanez line, They made the high end Ibanez Artists, The Gretch reissues, some other fine models as well as their own Tereda guitars. On to this baby The top is book matched SOLID AAA Spruce and the sides and back are mahogany, probably laminated but they seam to match?. either way *AWESOME* The SB model has a beautiful transparent cherry sunburst finish that is still so glossy looking it can pass for much newer but its 36 years old!. The Neck is also solid AAA mahogany with a beautiful rich looking rosewood fingerboard may be Brazilian Rosewood . The neck is RARE with a nicely v shaped which feels really good to me I think you'll be please with the feel as well. Setup done by our in house luthier & plays like butta now with a new set of acoustic Martin 11's, a $150 value. Now how ya gonna beat that! .
The Epiphone Company is a musical instrument company which was founded in the year 1873. Epiphone is specialized in making Guitars and are one of the largest producers of guitars in the world. Epiphone has several ranges to choose from, as they brand them in different groups. Few of the Epiphone ranges of guitars are, Epiphone Sheraton, Epiphone Casino, Epiphone Texan and The Dot etc. Besides guitars Epiphone also manufactured upright basses, banjos and other forms of stringed instruments.
Once the old selector is removed, screw the new selector in place. Follow your wiring notes from the old pickup selector, strip the wires with a pair of wire strippers, and solder the wires to the correct lugs. After everything is soldered in place, reattached the cavity cover or pickguard. For more information about how to solder wiring, see the soldering page.

The “Studio” model was introduced in 1983, and is still in production. The intended market for this guitar was the studio musician; therefore, the design features of the “Les Paul Studio” were centered on optimal sound output. This model retained only the elements of the Gibson Les Paul that contributed to tone and playability, including the carved maple top and standard mechanical and electronic hardware. However, the Studio design omitted several stock Gibson ornamentations that did not affect sound quality, including the binding on the body and neck. The two notable exceptions to this are the Studio Standard and the Studio Custom. Both models were produced in the mid-1980s, and included body and neck binding, though with dot fingerboard inlays instead of more ornate trapezoids. The first Studios from 83 to 86, except for Studio Standard and Studio Custom, were made with alder bodies rather than mahogany/maple. The current Studios come with a chambered mahogany body with either a maple or mahogany cap. The entry level Les Paul Studio “faded” has a chambered mahogany body and top and a satin finish and is the lowest priced Gibson USA Les Paul.
The ‘HSS’ refers to the pickup combination, with a humbucker and two single-coils, which is a versatile arrangement for both clean and distorted playing, especially when coupled with two tone controls and a five-way pickup selector switch. An excellent price for a good brand, and perfect for newbies. Make sure to check out the full review of this guitar.
After you have the hang of mono and stereo miking, room miking, and air guitar, you may be ready for the final frontier of El Gtr exploration. The time-consuming technique that I call "multisourcing" combines all the aforementioned methods, multiplied by the infinite possibilities created by splitting the guitar output and sending it simultaneously to different amps (using, for example, a Whirlwind Selector splitter box).
Most guitars have at least one tone control installed. They can be either assigned to a particular pickup (Strat or Les Paul) or work as master tone control (Ibanez and others). Electronically, it’s a variable low-pass filter. Lower the resistance, more treble gets cut which means that higher pot values will sound a bit brighter (typically 500K vs 250K). Capacitor values usually traditionally range from 0.022uF (22nF) to 0.047uF (47nF) but many people find these values too large and install much smaller caps instead. Values of 10nF, 6.8nF or even smaller are reported to work quite well (I used 10nF in my latest mod). To help you decide between cap values and composition, check out this site. It hosts a couple of useful videos with cap value and composition analysis.
You wouldn’t guess that this is a low-end electric acoustic, even on close inspection, because the build quality is superb. This translates to some great tone. While it might not have quite the same ring and sustain as an expensive model, only real audiophiles are likely to notice. You get a solid spruce top, good quality hardware, and Fishman electronics.
{"pageName":"[mf] pdp: epiphone firebird studio electric guitar","reportSuiteIds":"musiciansfriendprod","prop2":"[mf] shop: guitars: electric guitars","prop1":"[mf] shop: guitars","events":"event3,event50,prodView","evar51":"default: united states","prop5":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop6":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop3":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop4":"[mf] shop: guitars: electric guitars: solid body electric guitars","products":";519377","linkInternalFilters":"javascript:,musiciansfriend.com","channel":"[mf] shop","prop7":"[mf] product detail page"}
Aside from the stereo effect of doubling up the same part and panning it to opposite ends of the stereo spectrum, some guitarists use stereo rigs in conjunction with stereo effects. Traditionally, this involves using two amp cabinets, although single cabs that operate in stereo are available. To achieve a good, even stereo image, it’s best to mic each cab identically, ideally with the same type of mic. Invert the polarity of one of the channels to avoid any out-of-phase issues, and pan them hard left and right. Stereo effects such as reverb, delay and room ambience, can be added to mono guitar signals at the mixing stage.
Gold trapeze tailpiece with a diamond. For Gibson guitars including the following models- L-50, L48, ES-125, ES-330, etc. Please make sure to check the specs to see if they match your instrument to verify it is the correct replacement. Overall length of Tailpiece not including hinge = 4 5/8 inches. Side to Side width at bar = 3 19/64 inches. Width of string bar = 47/64 inches. String Spacing at Bar = 1 61/64 inches. Important Hinge/Mounting Specs: Mounting Area of Hinge length = 1 1/2 inches. Mounting Area of Hinge Width - 2 inches. Mounting hole location bottom center = 11/32 inch from bottom edge. Two Mounting hole locations from side edges = 5/16 inches. Two mounting hole locations Apart from eachother = 1 25/64 inches. Upper side of hinge length = 1 1/8 inches. Upper side of Hinge width = 1 25/64 inches.
As the market for iOS devices and apps has grown, so has the availability of affordable stompboxes and processors that can store downloaded effects. Being able to sample, purchase, and download effects through an iOS app or digital download gives you access to a whole new palette of sounds. Though relatively new, in years to come this may well become the way in which most players will assemble their effects libraries.
The simplicity and ergonomic design of the Pacifica PA012 body mirrors that of the PAC112. It is also available in exciting colors to match it perfectly to the player preference. Tonewood for PA012 as specified on the Yamaha catalog can either be in alder, nato or agathis, while the PAC112 is only made in alder wood. Neck for both guitars are made in maple with a satin finish then it is overlaid by a 22 medium frets rosewood fingerboard marked by inlay dots.

Lastly, we have guitars which combine the two systems and have both the piezoelectric pickup as well as a microphone in the sound box. Both of these sources are fed into a preamp, which often allows you to choose the source of the sound. Not only that, but you can also blend the two together to average out the benefits of both types while minimizing the negatives.
2. Orange Micro Dark w/1x8 Cabinet ($288): Who doesn’t love tiny yet mighty lunchbox amps and the speakers they rest upon? The Micro Dark head uses a tube front end to push 20-watts of power and coupled with a 1x8” speaker, you’ll be able to get awesome tube tone for a fraction of the price and size of a bigger rig. This little duo is well-equipped to handle clean and overdriven tones whether you are cracking the volume on the speaker or playing through your headphones.
The President was produced by Hofner in Bubenreuth, Germany, specifically for Selmer, who distributed the brand in the United Kingdom, Australia, New Zealand, South Africa, and other commonwealth nations. The President was a hollow body electric acoustic, available as a full body or thinline, and with blonde or brunette finish. It was a great playing guitar that sold fairly well in the second half of the 1950s, throughout the 1960s, and into the very early 1970s. The example shown here is a full-body depth guitar in blonde - and as a 1965 guitar, one of the last to feature the rounded Venetian cutaway. From late 1965 until 1972, the President sported a sharp Florentine cut. Naturally, such an electric acoustic suggests jazz and blues, but many of the original British Hofner President players were part of the rock 'n roll, skiffle and beat scenes of the late 50s and early 60s.

{ "thumbImageID": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "defaultDisplayName": "Ibanez RG6003FM Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Flat Sapphire Blue", "sku": "sku:site51409670719560", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue-1409670719560.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Flat Transparent Gray", "sku": "sku:site51393862854365", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Transparent-Gray-1393862854365.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000-00-60x60.jpg", "imgAlt": "" } ] }
In this buying guide, you’ll learn the essentials of what effects pedals do and which ones to look for depending on the kind of tone you want to experiment with. Here’s the quick overview: effects pedals (also called “stompboxes”) are electronic devices that connect in-line with your guitar and amp to change the signal going through them. Some work with analog circuits and some are digital, but they’re all powerful tools for shaping your sound in endlessly creative ways.
What is it about the Japanese and the Ventures? I mean, I cut my teeth with the Ventures. They were the perfect band to learn guitar from. The Ventures took songs with often complex harmonic structures—like the wonderful Johnny Smith classic—and stripped them down to their basic melodies, gave them a simple rock groove, and played them clean. I had the sheet music to Smith’s song, but there was no way in you know where I was gong to play off that. But follow along with the Ventures’ single? You bet!
The models in this list of best acoustic guitars have their own visual charm that appeals to different people. For example, the Blueridge BR-160 has those ornate inlays on the headstock. Some guitarists love those kinds of design elements, while others may find them a bit over the top and would much rather prefer the fretboard inlays on the PRS Angelus, or the simple but classic cutaway design of the Taylor 110ce.

Always use more than one mic, and when possible, double down on the amp as well. This will give you additional options in the mixing phase. You can split the signal to the amp by employing a stereo FX pedal or a DI. The second mic doesn’t necessarily have to be close to the cabinet and can be placed as far as 3 ft away to give you more tonal range.   


{ "thumbImageID": "Brian-May-Signature-Electric-Guitar-Antique-Cherry/512637000593000", "defaultDisplayName": "Brian May Guitars Brian May Signature Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51274319719826", "price": "849.99", "regularPrice": "849.99", "msrpPrice": "1,308.00", "priceVisibility": "1", "skuUrl": "/Brian-May-Guitars/Brian-May-Signature-Electric-Guitar-Black-1274319719826.gc", "skuImageId": "Brian-May-Signature-Electric-Guitar-Black/512637000001000", "brandName": "Brian May Guitars", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Brian-May-Signature-Electric-Guitar-Black/512637000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Antique Cherry", "sku": "sku:site51274319719831", "price": "849.99", "regularPrice": "849.99", "msrpPrice": "1,308.00", "priceVisibility": "1", "skuUrl": "/Brian-May-Guitars/Brian-May-Signature-Electric-Guitar-Antique-Cherry-1274319719831.gc", "skuImageId": "Brian-May-Signature-Electric-Guitar-Antique-Cherry/512637000593000", "brandName": "Brian May Guitars", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Brian-May-Signature-Electric-Guitar-Antique-Cherry/512637000593000-00-60x60.jpg", "imgAlt": "" } ] }

I went to my local guitar store, and tested every one on the wall (under $1,000). I narrowed it down to two (the Ovation acoustic-electric of the same caliber, and this Yamaha FGX800C). In the end I ordered this guitar because of the excellent price on the "package" deal (hard case, strap, tuner, etc.). It sounds fantastic, stays in tune very well, is comfortable to play, and no "buzz". My limit of 4 stars is due to; 1) The strap is garbage...get a new one if you play with a strap. 2) The guitar only has a strap post on the rear of the instrument (it also doubles as the connection for the amplifier cord), and there is none on the front. You have to tie a string ahead of the nut. That gets in the way of the tuning and fingering of

In terms of the electronics, Yamaha went with a System 66 piezoelectric platform. The preamp packs a standard three-band EQ couple with a built-in tuner and a flexible mid-range control. Needless to say, it gives you more than enough room to dial in a decent tone. Quality-wise, this might be the best acoustic electric you can get in this price range, period.

The primary difference in tone between the solid body and hollow body guitar is the high end bite one associates with the solid body guitar. From the biting rhythm of guitarist Nile Rodgers to the supersonic leads of Eric Clapton and David Gilmour, Stratocasters have found favor with so many guitarists because of their versatility and their timeless tone.

I would have never finished my project without this, 20 feet sounds like alot, but it can go very fast. I used this to rewire up an Epiphone hollow body,and I needed the length to reach from toggle to jack. The gauge is a perfect feel and doesnt have me worried about accidentally breaking it from movement. Also the cloth is great as it takes much more heat than the standard rubber coverings.
I have to say I'm really impressed with the Obsidian HSS wiring harness, The build quality is top notch, and the simplicity to install really delivered.It only took a few minutes to connect and be up and running. I love to customise my guitars and love to play around, so having the ability to swap out pickups without a messy soldering iron is fantastic, and the wiring is super clean giving a professional finish. I'll be intending to use the obsidian wiring harness in future project guitars -I highly recommend- Guitar sounds great ( oh did I mention the extra guitars picks too. nice touch)" - Ricci Custom HSS Strat® Wiring
Gain is the strength of the electronic signal carrying your sound. A standalone gain booster is essentially just a preamp, and can be an effective way to overdrive the preamp section of your amp, creating easier musical-sounding breakup and increasing the amp's power. A gain booster in a stomp box lets you instantly boost your sound level for solos without altering your fundamental tone.
The old ones were SOLD as cheap guitars. These new ones, at their price points, are probably decent instruments at the very least, and possibly even very good ones. I doubt they have much in common with the Kays from the 70s aside from how they look, which as other people have detailed, is probably just for nostalgia purposes. Lots of aging rockers with fat salaries who might've learned on those guitars a few decades ago!

While all of the brands featured in this guide produce wonderful instruments, the clear all around winner is Fender. Fender somehow manages to feature the best of both worlds in nearly every category. Guitar players have been turning to Fender for over seventy years, and for good reason. The company is renowned for its high quality craftsmanship and their beautifully constructed instruments have been inspiring guitarists for decades.


The MESA Bigblock 750 has a built-in overdrive channel. The Mesa M2000 has a high gain switch which can be engaged with a footswitch. The Marshall MB450 head and combo bass amplifiers have a tube pre-amp on the "Classic" channel which can be overdriven. The Ashdown ABM 500 EVO III 575W Bass amp head has a built-in overdrive effect. Overdrive is also available on many Crate bass amplifiers. The Yamaha BBT500H has three types of built-in drive effects: overdrive, distortion and fuzz. The Ampeg B5R Bass Amplifier has two channels: clean and overdrive, with the ability to combine the two. Verellen, a boutique amp company, produces a bass amplifier with a built in overdrive channel.
Originally, distortion of the guitar signal happened accidentally when tube amps were turned up too loud. While distortion was first considered undesirable, players soon came to recognize that a distorted signal increased the amount of sustain they could get out of each note. This essential discovery created a fundamental shift in guitar soloing styles to include extended notes such as those produced by a wind instrument or organ. Used on rhythm guitar parts, distortion thickens up the signal and allows for a much heavier, chunkier sound.
A selection of makers within the high-end, hand-built crowd of today do offer variations on the opamp-based template discussed above. Blackstone Appliances bases its Mosfet Overdrive on a discrete transistorized circuit centered around, yes, mosfets, and Klon’s Centaur pedal uses… well, who the hell knows? They cover the entire circuit board in epoxy goop to keep the cloners at bay, but this expensive overdrive certainly sounds different. Other popular boutique overdrives are found in the Barber Electronics LTD pedal, the Crowther Audio Hot Cake, and the Fulltone OCD.
In this installment of Gibson Tone Tips we’re going to take a look at a simple factor of any guitar’s set up, but one that newer players often approached from too a narrow standpoint. When a learner first picks up the electric guitar, he or she is often most drawn to an instrument that has the strings as low to the fingerboard as is functionally possible, because this is easier on tender, unfamiliar fingers, and makes that guitar feel more comfortable in the beginner’s hand. From this point on, our “feel preference” is often set, and we take this “low action=great guitar” bias with us from guitar to guitar, throughout our playing career, imposing it forever after on guitars that we set up ourselves.

For an overdrive pedal, turn your attention to the Fulltone OCD Obsessive Compulsive Drive Overdrive Guitar Effects Pedal. Compact yet versatile, this pedal is great for anyone who likes a raw vintage-like overdrive, and it even makes a great boost pedal. Now, if it's a distortion pedal that you're after, take a closer look at the Electro-Harmonix Classics USA Big Muff Pi Distortion/Sustainer Guitar Effects Pedal. The Big Muff Pi is a legendary pedal in itself, and this reissue has 3 controls that let you dial in the finest harmonic distortion/sustain ever produced. From warm bass to crisp treble, you'll be blown away by what this distortion pedal can do for your hard-rocking guitar performance.


When connecting more than one pickup, it’s important to follow the manufacturer’s color codes and wiring diagrams so that the phase relationship is correct. The phase relationship of a pickup is determined by the winding direction of the coil and the polarity of the magnets. The two coils of the traditional humbucker are connected in series with the phase relationship shown in Fig. 1. Most modern Stratocaster® style guitars with three single-coil pickups are supplied with a reverse wound/reverse polarity middle pickup for a parallel hum canceling effect when the guitar is switched to a two pickup position (e.g. neck & middle pickup together) as shown in Fig. 2.
The benefit of a compressor lies in that every note played will be at nearly the same amplitude, and therefore nearly equal in volume. This will help normalize tones that are sometimes lost in the mix because of complex overtones, and it will result in a more articulate sound. Notice that if you don’t pick all notes of an arpeggio at exactly the same pressure you will likely get a different sound for each note, especially if you are playing a tube amp. Tube amplifiers react dynamically to stronger and weaker signals it’s the allure of them and thus the non-uniformity of picking at different strengths will be exaggerated. A compressor will fix this problem and normalize all notes of the arpeggio regardless of the player’s technique and equipment, which is consequently why many soloists prefer them.
At the more reasonable end of the price scale compared to other Gretsch guitars, sits the Gretsch G2655T Streamliner. While not an arch top like the guitars listed previously, this guitar does feature a hollow bodied design. As such, it perfect for clear, ringing chords and lead lines. Also in its favour is the G2655T Streamliner’s thinner body depth. This makes it more comfortable and slightly less cumbersome than the bigger, more traditional jazz guitars. You’ll also get more versatility from a ‘regular’ semi acoustic, meaning you can dabble in blues, rock and country with the Streamliner models.
All mass-market brands offer at least one distortion pedal—and often many. Boss, for one, tries to cater to all possible tastes. Its DS-1 (not to be confused with the SD-1 overdrive mentioned above) is one of the workhorses of the breed, with some big-name players happy to stomp on its rectangular switch, including both Steve Vai and Joe Satriani. The DS-2 takes things a step further, while the MT-2 Metal Zone and MD-2 Mega Distortion get successively more evil. And Boss isn’t the only one, with DOD, Ibanez, Marshall and many, many others playing the game too, along with a few of the boutique makers. The proliferation is most distinctive in many “metal” pedals that go beyond even the standard distortion sounds. These generally offer the archetypal scooped-mid sound with thudding lows and crispy highs. Many are adjustable for anything from classic rock to metal sounds, with a tone control that acts more to reduce or accentuate mids rather than the usual high boost/cut, and often a “resonance” control or similar to adjust the fullness of the bass.
Ovation guitars are produced in the U.S. as well as in Korea and China. Those models in general have a wooden top. Recently Ovation significantly reduced the production of U.S. made Ovation models. From 2010 on better models (e.g., Legend, Elite, Custom Legend, Custom Elite) used to be available, both, made in the U.S. and made in Korea. Before that, the mentioned models were U.S. made. In recent years many U.S. made guitars could be identified by the LX in the product name (e.g., Legend 2077LX), whereas the Korean-made version of the same guitar had AX in its model name (e.g., Legend 2077AX). Again, this name-system has not been used throughout the whole guitar model range (e.g., Ovation 1617ALE). Nowadays only a few U.S. made models are being produced, mostly signature and limited edition models (e.g., Custom Legend 1769-ADII Al DiMeola). Production of the standard model range of Ovation guitars in the U.S. has been seized.[24]
Here we have is one of the finest vintage Banjo's you will ever see. This example is a 32 year old High End no expense was spared. Its super well built with top grade materials like Brazilian Rosewood fingerboard and Mother of pearl inlay work just about everywhere WoW!... just have a good look at its AAA flamed Maple back and its AAA flamed Maple Neck.. this one is super nice and well its clean. The action is great and she has a very good feel & sound. More to come soon...stay posted for updates Thanks for looking. .
Pressing a string against a fret reduces the vibrating length of that string to the distance between the pressure point and the bridge, thereby controlling pitch. On nearly every Western fretted instrument, the distance between frets is a semi-tone of equal temperament, assuring the easy achievement of strong sounding chords and single notes that fit our hemisphere’s usual expectations for rhythm sounds and melodies. Understanding the virtues and limitations created by the order of frets opens up the door to ways to escape their constricts, like bending strings, playing slide, using whammy bars, delving into extended technique or trying fretless instruments.
There are times when a single-coil just doesn’t have enough twang. I’ve encountered Strat neck pickups that are just too wooly to provide me with that saucy, SRV/Hendrix-style rhythm juice. Or, sometimes an anemic bridge pickup just needs an extra dose of snap to push it into Tele-like territory. If so, this simple mod could be just what you’re looking for.
So I was all, "oh no...I want this one." So I did leave with it, and without even asking they sold it to me at less than the price on the thing because it was the demo and had a tiny belt buckle type scuff or two on the back. I think I actually wound up saving a few hundred dollars. I don't know if they figured a percentage of the total should be knocked off, or what.
Launch price: $599 / £500 | Body: Basswood | Neck: Hard maple | Scale: 25.5" | Fingerboard: Rosewood | Frets: 22 | Pickups: Manson Design bridge humbucker, Manson Design neck single coil | Controls: Volume, tone, 3-way selector switch | Hardware: Two-piece bridge and tailpiece, staggered height locking machineheads | Left-handed: Yes: MBC-1LH | Finish: Matt Black
Guitar strap: If you intend to stand up while playing on guitar during live shows (and most people do), then you need to practice in the same position like when you’re playing live. Your muscles and hands are in a completely different position when you’re sitting down and when you’re standing, and that’s why you MUST get a strap right from the start and practice standing up, as well as sitting down. Price: $10 – $15 should do the trick.
In the ideal scenario, once set, your saddles should neither be flush down on the bridge assembly of the guitar, nor extended so high they could go no further. This saddle height relative to the bridge assembly is a reflection of the neck angle. If the saddles sit flush, the neck angle is not set back very far and vice-versa. This is where you should decide if your neck angle is in need of adjustment ( if you have a bolt-on neck). Check the measurement at the 12th fret then progress up the neck, measuring every couple of frets. The string height should continue to gradually rise, if it doesn't the neck is set back too far and has to be tilted up just a little. This is a very sensitive adjustment and the thickness of a couple sheets of paper can make a big difference. Some Fenders have a neck tilt adjustment screw that is accessed with an Allen wrench through a hole in the neck screw plate. The strings must be loosened, then the neck screws, then the tilt adjustment screw is tightened or loosened. Never do this when the neck screws are tight! If you don't have a tilt adjustment, thin shims of wood veneer are fitted in the neck pocket to adjust neck angle. Uneven frets are also a possibility. If , after having followed all the above steps, you are still getting fret buzz, you must establish that the frets are all even. But this leads us to fret dressing, which is another story altogether.
In the late 1950s, Guitarist Link Wray began intentionally manipulating his amplifiers' vacuum tubes to create a "noisy" and "dirty" sound for his solos after a similarly accidental discovery. Wray also poked holes in his speaker cones with pencils to further distort his tone, used electronic echo chambers (then usually employed by singers), the recent powerful and "fat" Gibson humbucker pickups, and controlled "feedback" (Larsen effect). The resultant sound can be heard on his highly influential 1958 instrumental, "Rumble" and Rawhide.[17]
*When the item leaves our warehouse, they are generally shipped to EMS Worldwide Express Mail Service and it would usually take 7 – 10 days to United States. We ship our products from Mainland China where our manufacturing factory is located. We will inform you once your order has been shipped and we will be providing you with the tracking number so you can conveniently monitor the shipments progress on EMS Worldwide Express Mail Service website or SF Express and USPS and Parcel Force website.
We perform within include rings. Personal big assortment of pedals, a few I really like, a few foul odor. I quickly discovered how the just people who worry about the results tend to be additional music artists. The actual people( ladies dance mostly) might treatment much less. Therefore right now I acquired the tuner, as well as generate your pedal with regard to single sculpt.... that is this, as well as my personal sculpt rocks ! as well as straight forward. With regard to facilities felines it might be another tale.

Many people will say that Overdrive and Distortion pedals are basically the same thing: wrong! While the overdrive tends to add gain and texture to your clean tone, emulating a cranked amplifier, the distortion intentionally clips and distorts the waveform of the guitar signal. The effect of distortion pedal is much more audible and the resulting sound is harsher and louder, and sometimes completely different from the starting sound. Distortion pedals are perfect for rock and metal players, and represents a safe boat for guitarists that may feel the need to have a backup to their tube amplifier: a distortion pedal into the clean channel of a rented amplifier can save your gig! The ProCo Rat 2 is an instant classic, while the Electro Harmonix Metal Muff/Top Boost gives you some serious distortion with a top boost in single box. And for your über-metal needs, the Harley Benton Extreme Metal is here to help.
Hollow-body guitars are best suited for classic jazz, but some musicians have used them in rock, country and blues. If you are a non-jazz guitarist interested in this kind of instrument I’m going to assume you know what you are doing. While these types of guitars can sound great with overdrive in the right hands, they’re probably not the best choice for most rock players.
As you will note in the earliest catalogs, Ibanez guitars were first "copies" or "reproductions" of guitar models originated by several American guitar manufacturers and manufacturers from other countries. They were not forgeries, as they were never sold with misleading logos or with the intent to deceive. Ibanez models replicated such styles as the Gibson Les Paul, Fender Stratocaster and Telecaster, Rickkenbacker styles, and others. Due to their high quality, Ibanez guitars and those made under other brands, such as Greco and Aria, quickly earned a reputation around the world as quality instruments at a great value. There is a form of urban legend that circulates in the guitar community that has many variations, but usually involves either Gibson or Fender suing Ibanez, Aria, or some other Japanese manufacturer, with the intent to stop that company from manufacturing superior copies. The truth is less glamourous. Only one company ever sued another, and it was Norlin (the owner of the Gibson brand at the time) suing Hoshino (owner of the Ibanez brand) and the suit was focused only on the "open book" headstock shape common to Gibson guitars and replicated on the Ibanez guitars. The suit was brought in 1977, but by then Ibanez had already changed the headstock shape on its copy models, so the suit was settled out of court. No other company was ever sued by any other company. However, this episode has given rise to the term "lawsuit" guitar, which is used to describe any Japanese copy guitar made in the shape of an American manufacturer's model.
The volume pedal is about as simple as a pedal can get. It is basically an external volume knob that you work with your foot. They are an excellent way to control the volume of your rig and can be placed at different places in your guitar chain. When placed first for example it can be great for volume swells (as we will see), reducing your amp gain by acting like your guitar’s volume knob. If placed after your gain section it will bring down your overall volume without reducing changing your tone or gain. You can really experiment with the placement of a volume pedal to see what matches your needs.

{savingPercent=0.00, isPreOrder=false, pimStatus=R1, visibilitySalePrice=9.99, typeCondition=New, statusText=In stock, isPriceDrop=false, displaySku=451058000001000, invMsgBackOrdered=false, skuPriceVisibility=1, stickerUrlLink=null, kitCarouselSkuIds=1500000222576,1363016749098,1368456537505,1300744185161,1377190992159,1500000250930,1368456537510,1363811587202,1500000222578,1500000154196, stickerURL=null, availableDate=Wed Feb 27 04:20:22 PST 2019, invMsgAvailability=, serialized=false, listPrice=9.99, isShipsInternational=true, name=Black, invMsgBuyToDemand=false, partNumber=SSG-303 BK-MG, MSRP=24.99, inventoryStatus=1000, newPrice=9.99, condition=New, status=instock, stickerClass=null, stickerText=Top Seller, invMsgOverSized=false, invMsgDetail=, YourSaving=0.0, MSRPRange=false, invMsgPreOrder=false, invMsgVendorDropShip=false, availableInStoreOnly=false, prop65=WARNING: This product can expose you to chemicals including Vinyl chloride, which is known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov., salePrice=9.99, warranty=false, displayId=1274228076940, stickerDesc=Top Seller, isOnSale=false} 9.99 USD
Although the hollow bodies of these guitars create a mellow, naturally voiced tone perfect for jazz, vintage country and other styles that require warmth and clarity, they can also snarl. For proof of the latter, check out Lennon’s performances on “Revolution” and “Cold Turkey.” Too much volume or proximity to the amplifier, however, and hollow bodies can howl with feedback unintentionally. And that’s why the semi-hollow body guitar was invented.
{ "thumbImageID": "LX200B-Series-III-Electric-Bass-Guitar-Metallic-Blue/H11151000001000", "defaultDisplayName": "Rogue LX200B Series III Electric Bass Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Metallic Blue", "sku": "sku:site51278002525869", "price": "109.99", "regularPrice": "149.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Rogue/LX200B-Series-III-Electric-Bass-Guitar-Metallic-Blue-1278002525869.gc", "skuImageId": "LX200B-Series-III-Electric-Bass-Guitar-Metallic-Blue/H11151000001000", "brandName": "Rogue", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/LX200B-Series-III-Electric-Bass-Guitar-Metallic-Blue/H11151000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Pearl Black", "sku": "sku:site51278002525872", "price": "109.99", "regularPrice": "149.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Rogue/LX200B-Series-III-Electric-Bass-Guitar-Pearl-Black-1278002525872.gc", "skuImageId": "LX200B-Series-III-Electric-Bass-Guitar-Pearl-Black/H11151000002000", "brandName": "Rogue", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/LX200B-Series-III-Electric-Bass-Guitar-Pearl-Black/H11151000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Candy Apple Red", "sku": "sku:site51278002525875", "price": "109.99", "regularPrice": "149.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Rogue/LX200B-Series-III-Electric-Bass-Guitar-Candy-Apple-Red-1278002525875.gc", "skuImageId": "LX200B-Series-III-Electric-Bass-Guitar-Candy-Apple-Red/H11151000003000", "brandName": "Rogue", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/LX200B-Series-III-Electric-Bass-Guitar-Candy-Apple-Red/H11151000003000-00-60x60.jpg", "imgAlt": "" } ] }

Most Humbuckers are wired in anti-phase, where the opposing polarity of the localised magnetic fields cancel each others out at selective points, creating a lower bandwidth region in the high frequency domain. Less bandwidth = lower noise. If done correctly, with carefully designed pickups, it will not affect the tone, but traditionally it did, because Hillbilly wannabe technicians made the things on their knees.

In 2005, after two years of research and development utilizing Jimmy Page’s actual guitar, Gibson Custom Shop issued a limited run of Jimmy Page Signature guitars based on Jimmy Page’s No. 1 1959. This time, Gibson worked directly from Jimmy Page’s actual guitar, which he lent to Gibson for the project. The guitar featured just one push-pull pot, just like Page’s No. 1, which reversed the phase of the pickups in the up position, which in Page’s own words gave “a close approximation to the Peter Green sound.” Gibson also went to great lengths to replicate the accuracy of the pickups, creating two custom pickups, which were available only in this guitar. The pickups were based on the Burstbucker vintage-style pickups, but featured stronger Alnico magnets and slightly higher output than the other Burstbuckers, as well as slightly higher treble response, which accurately reproduced the sound of the pickups in Page’s guitar. Gibson also replicated the neck profile, which was heavily modified prior to Page acquiring the guitar, and the Grover tuners that Page favored.
I’m starting at guitar too at sixty years old, my opinion is that it’s not the guitar, but the time put into practicing, you can dup any type of sound with the features from amps, and guitar processors. You can even make an electric guitar sound like an acoustic. I purchased a line 6 150 watt amp, and a processor from line six, and I can dup any type of guitar sound. I built my own guitar
This guitar master knows wood. He understands its rhythm. He's a master woodworker and began building acoustic guitars when he was a child. "I couldn't afford the ones I wanted," he says, "so I built them." Perretta Guitars is the result of his experiments. But it wasn't until he toured with the guitars that he'd receive some of the best advice of his life from George Gruhan, a guitar master in Music City, whose customers included Eric Clapton, Neil Young, Johnny Cash and George Harrison: "If you want to work in this business, do repair work."
With over 8 decades of development, the electric guitar and music from guitars is getting progressively more sophisticated. Nowadays there are thousands of models available, from a number of manufacturers; electric guitars come in all kinds of shapes and sizes – some reminiscent of the regular acoustic guitar, and some drastically different from the traditional instrument. Regardless, there's a number of features which are invariably present in practically every electric guitars: the headstock, neck, body and strings. The headstock includes the machine heads, truss rod (may not be used in all models), string guide and nut; this section is used for tuning and holding/adjusting the strings. The neck serves the function of supporting the strings, and it's comprised of a fretboard, the inlay fret markers, the actual frets and a neck joint. The body of the guitar is comprised of several mechanisms including the pickups (neck and bridge), saddles, tuners, pickup switch, control knobs (tone and volume), output connector and strap buttons – sometimes others, in more sophisticated models. Finally, the strings are usual divided in brass and treble variants.
While often overlooked, the speakers are an amp’s most crucial component—they’re the last thing standing between all that electronic gobbledygook and the sound that reaches your ears (except for yo’ mama’s fist, but that’s another story). Different sized speakers have different tonal characteristics, and you should consider speaker sizes the same way you’d consider an amp’s wattage rating. Speakers are like booty—small ones are tighter and big ones have more bottom end. But like a pair of pants, cabinet design can shape bottom end as well. Which is why a closed-back 4x10 cabinet may put out more bass than a 15-inch speaker in an open-back cabinet.
Looping – These pedals are miniature recorders that capture a passage, which you can then play back as much as you like. Many looper pedals also allow you to layer multiple recordings, and advanced models support extra features like built-in rhythms, mic and other instrument inputs, MIDI, USB and more. It’s worth noting that all the power of a looper pedal does come with a steep learning curve, so be sure that you’re experienced enough to handle one of these bad boys before you bring home one of your own.
The Effect: Compression rose to fame in the rock and roll era, many famous musicians used (and still do) compressor pedals in order to add distinctive sustain in their performances, attracting the listener’s attention and making them stand out from the diverse instruments playing along. Some of the most famous compression pedals are the “Ross Compression” and the classic “MXR Dyna”, which have been subject to imitations and remakes ever since their original releases. Compression pedals have remained popular to this day, and are considered a must-have in many guitarist’s arsenals.

Modulation stompboxes like our BF-3 Flanger should be after the tone-producing effects like distortion, wah, etc. so they can process and modify the tone built by the pedals before it. If you put it before the distortion, then you are distorting the sound of the flanger. Maybe that’s what you’re after, but in general, put the BF-3 and other modulation effects after the tone-shaping (and noise–producing) pedals. And then there are the ambience effects: delay and reverb. As we discussed earlier, reverb—and sometimes delay, depending on the space—is the last thing that happens before the sound reaches your ears in a physical space, so these go last. Delaying reverb can sound muddy, so it’s usually better to have the reverb after the delay.
You can always rely on Epiphone to provide an acoustic guitar with eye-catching looks and a quality sound at an excellent price, and the EJ-200CE is certainly a testament to this. Based on one of the world’s most famous guitars, the J-200 (introduced in 1937), this revamped model offers an excellent mix of vintage style and modern components, perfect for any level of skill.
Guitar is well made. Sounds awesome. The overall height of the strings (in relation to the frets) were not bad. However, it needed to be setup. After having the guitar setup at my local shop, it is so much easier to play (don't have to press as hard on the strings). The Guitar gig bag that comes with the bundle offers zero padding. The Tuner works well, however, since the guitar comes with a built-in tuner, you don't need a separate one. I have not used the dvd that came with it. I use a different set of instructional dvds (purchased separately). Overall a great guitar. Definitely recommend it.
The Squier Vintage Modified Jaguar is a beauty on it’s own. Back in the days the jaguar was used for country music, early rock ‘n roll and jazz, but eventually it has found it’s way onto the stage of surf, funk, alternative, grunge and rock music. The guitar features include a basswood body, maple neck, circuit selector and tone circuit switches, pickup on/off switches, skirted black control knobs (lead circuit) and black disc knobs (rhythm circuit), vintage-style bridge and non-locking floating vibrato with tremolo arm, vintage-style chrome tuners and chrome hardware. A real good guitar for the price. If you want decent and different, this is it!
During final construction, a small section of the outside corners is carved or routed out and filled with binding material on the outside corners and decorative strips of material next to the binding, which are called purfling. This binding serves to seal off the endgrain of the top and back. Binding and purfling materials are generally made of either wood or high quality plastic materials.
From what I've been able to find out (as a proud owner of a mint W-415 'Dove' model acoustic), Lyle guitars are actually Gibson seconds, that for whatever reason didn't pass muster to be sold as a Gibson (bad finish, scuff, imperfection in the wood, etc.). The Lyle company was out of Portland, OR (I believe) and was started by former Gibson employees who would fix the flawed Gibsons and resell them under the Lyle name. Made in Japan was because Gibsons were made in Japan at the time(?). A damn fine instrument; considered rare now, I guess. I don't ever want to get rid of mine!
Reverb is one of the most fundamental effects for electric guitar, which is why it is already built into most amps. Reverb adds natural sounding depth to your sound. Used extensively in the recording world, electric guitars do not sound “right” without it. Just a little makes the guitar have more of a natural sound and decay, but you can go to the extremes and get cavernous depth to your sound. Plate and spring are the most common types, but with so many makers coming up with new sonic “spaces” to play in, finding your reverb sound is a priority.
The SS-4L was almost identical in electronics and other appointments to the SD, with the main differences being in body shape, vibrato and pickups. The body was more like a Strat, except the entire lower horn was lopped off and slanted toward the lower bout. Very, very… well, this is one of those ideas that’s so ugly it becomes beautiful! This had a new, very nifty vibrato system, one of the coolest the Japanese ever produced. This consisted of a plate or platform resting on springs, sitting above the top of the guitar. This then had a metal block with several holes along the treble side, into which the arm was inserted and secured with a thumbwheel screw. The SS-4L had two-tone metal-covered pickups with six poles along the rear edge, two half-slots exposing a gold insert in the center and six holes showing the insert along the front edge. These “two-tones” would become a mainstay of many early ’60s Teiscos.
Keyboard players who use subwoofers for on-stage monitoring include electric organ players who use bass pedal keyboards (which go down to a low "C" which is about 33 Hz) and synth bass players who play rumbling sub-bass parts that go as low as 18 Hz. Of all of the keyboard instruments that are amplified onstage, synthesizers produce some of the lowest pitches because, unlike a traditional electric piano or electric organ which have as their lowest notes a low "A" and a low "C", respectively, a synth does not have a fixed lowest octave. A synth player can add lower octaves to a patch by pressing an "octave down" button, which can produce pitches that are at the limits of human hearing.
Experience Rockstar Games' critically acclaimed open world game, Grand Theft Auto V. When a young street hustler, a retired bank robber and a terrifying psychopath find themselves entangled with some of the most frightening and deranged elements of the criminal underworld, the U.S. government and the entertainment industry, they must pull off a series of dangerous heists to survive in a ruthless city in which they can trust nobody, least of all each other. Explore the stunning world of Los Santos and Blaine County in the ultimate Grand Theft Auto V experience, featuring a range of technical upgrades and enhancements for new and returning players. In addition to increased draw distances and higher resolution, players can expect a range of additions and improvements including: New weapons, vehicles and activities Additional wildlife Denser traffic New foliage system Enhanced damage and weather effects, and much more Grand Theft Auto V also comes with Grand Theft Auto Online, the dynamic and ever-evolving Grand Theft Auto universe with online play for up to 30 players, including all existing gameplay upgrades and content released since the launch of Grand Theft Auto Online. Rise through the ranks to become a CEO of a criminal empire by trading contraband or form a motorcycle club and rule the streets; pull off complex co-operative Heists or enter radical, adrenaline-fueled Stunt Races; compete in unique Adversary modes; or create your own content to play and share with the Grand Theft Auto Community.
Great guitar for the aspiring 4-10 yer old. This Lotus 20.25" scale, Kid's Strat copy is in excellent condition! Featuring a maple neck, an unbound rosewood fret-board, simulated mother of pearl fret marker, dot side markers, graphite nut, 6 "in-line" head stock, and an adjustable truss rod. 3 strat style, single coil pickups with 5 position selector. Volume and tone controls. (While not photo'd, the guitar does include the whammy / tremolo bar). This guitar is in great shape with virtually no wear to the original gloss black finish. I actually special ordered it when I worked at Colorado Springs Music Company for my son. I think he took it out of the gig bag a couple times. Comes with a thick padded "codura" gig bag.

SSO Strings (Sonatina Symphonic Orchestra) is a creative commons licensed library. For violin, chamber strings and flute I have taken several of the instrument samples and layered them together to allow for expressive playing over the velocity range. Flute SSO for example contains soft, hard and overblown samples from SSO. To create chamber strings I have used bass strings, cello, expressive violin and viola over certain ranges of the keyboard.
Vacuum tubes were the dominant active electronic components in bass amplifiers manufactured from the 1950s until the early 1970s, and tubes continue to be used in the 2010s for expensive bass combo amplifiers, amp heads, and preamplifiers (as well, tube amps continue to be used by audiophiles for some expensive home hifi stereo systems). Tube amplifiers for bass almost always use class AB1 topology for efficiency reasons.
There's no denying the popularity of the Stratocaster, thanks to it being the weapon of choice for a long list of iconic players that include Jimi Hendrix, Eric Clapton and Jeff Beck to name a few. The American Professional Stratocaster is the latest iteration of this classic, carrying over much of the look and feel of the original, but more reliable and road worthy.
Larrivee is much 'closer to home' and have been operating out of California since 2011. Although you can buy their instruments from Guitar Center and Amazon, and I personally like what I've read about their approach to lutherie, they didn't quite score high enough to make the final cut due to the method I used having a bit of a bias toward wide availability - I may rethink the approach if I revisit this topic.
SSO Strings (Sonatina Symphonic Orchestra) is a creative commons licensed library. For violin, chamber strings and flute I have taken several of the instrument samples and layered them together to allow for expressive playing over the velocity range. Flute SSO for example contains soft, hard and overblown samples from SSO. To create chamber strings I have used bass strings, cello, expressive violin and viola over certain ranges of the keyboard.

Just SOLD #2 another fine example of the vintage 1960s era J200 copy by the great luthiers at Alvarez in the mid 1970s - the 80's WoW very well done impressive... Alvarez from over 40 years ago. This example is JVG rated at very good + 8.6/10 vintage condition with beautiful patina and character mojo as well so cool Gotta love this Beauty! This instrument has received our JVGuitars "set up" and several upgrades as well we have installed a new set of Martin 80/20 bronze Marquis strings for a crisp tone with great bass and volume as well as a Martin solid natural bone nut & a compensated saddle set custom fit into its original fully functional adjustable bridge with plenty of room for up or down adjustments to your personal taste further upgrades do include throwing out the old plastic tone robbing bridge pins for the superior resonation of solid ebony wood with brass ring and beautiful abalone inlay bridge pins and this was for tonal reasons and it looks much more high end as well, then we removed the old economy tuners of the era ( a weak point ) and installed a set of Grover tuners old holes were touched up in the process looks good and works excellent now to keep this guitar in tune and as a side benefit the added girth at headstock increases sustain as well. The medium slim profile C shaped neck is 1-11/16ths at the nut and also is pretty much the same as the 60's Gibby profile the frets are the originals as well and still playing well without buzz as per JVG set up. Truss rod is working fine and the headstock is looking cool with its Old School script Alvarez mother of pearl logo and crown design with its patina and cool old Alvarez Truss rod cove this guitar is striking as well. Great sounding like a Piano wow and she's playing with ease with excellent string action now. She retains her excellent vintage Sunburst and finish still shines nicely of course she is not new or mint it has some natural finish checking several that only adds to its Mojo along with several doinks here and there on the body and top a few that caught edge near binding on front and back not so big rather small and small paint had chipped off and so I addressed them with a fine tip matching color lacquer tip pen to touch up and to help preserve original finish integrity and looks much better as well. We also installed a replacement pickguard and it fits perfectly and looks great too. The 1960's VIBE and this instruments playability makes this an excellent choice for that SWEET Jumbo tone well crafted over 40 years ago Vintage Script Logo on headstock inlayed in mother of pearl on correct law suit era open book Gibby style headstock. Made in Japan well taken care of all these years and ready for you to enjoy another 40. Overall she is SWEET! Contact Joe to buy: jvguitars@gmail.com.


Reverb is one of the most fundamental effects for electric guitar, which is why it is already built into most amps. Reverb adds natural sounding depth to your sound. Used extensively in the recording world, electric guitars do not sound “right” without it. Just a little makes the guitar have more of a natural sound and decay, but you can go to the extremes and get cavernous depth to your sound. Plate and spring are the most common types, but with so many makers coming up with new sonic “spaces” to play in, finding your reverb sound is a priority.
A. It is never too late to learn how to play a musical instrument. An acoustic guitar does present some unique challenges for beginners, including the formation of calluses over time. Some working professional guitarists actually develop deep grooves on their fingertips after years of performing. But this is not a requirement in order to become an accomplished amateur guitarist. Practically every musical instrument places some physical demands on players, but developing skills like muscle memory and improvisation are tangible benefits of that extra effort.
Although much less common, the second trick I have in store for you shouldn't be taken lightly. The idea is to double a more or less distorted guitar part with an acoustic recording of the strings of your electric guitar recorded simultaneously as the distorted part. As preposterous as it sounds at first, considering that the sound of an electric guitar without an amp is certainly not the most pleasant one, the overall result can be truly amazing! Indeed, well managed, this screeching sound has the particularity of adding a bit more dynamic relief to "trashy" sounds, providing the performance a more "organic" aspect, especially due to the accents produced by the pick. But just like with the first trick, you need to sub-mix this take wisely so that the listener doesn't end up discovering the trick.
here is an example of why an acoustic reigns supreme for practical reasons. Last week, I had to get new tires on the truck. Knew I had a couple hours to kill while there. the Discount Tire was on the way to my guitar teacher… in a big way (an hour drive up to Denver for guitar lessons, the Discount was half way there). So, I brought my acoustic in to Discount and played for a couple hours in the waiting room. People loved it, and were shouting out requests and stuff.
Like the Les Paul, the SG guitar models has an iconic status and it is another guitar coming from Gibson that has been passed-on to Epiphone to cater a wider audience because it carries a much friendlier price. This SG Special has the famous devilish cutaway body made from mahogany and has a bolt-on okoume neck with a comfortable to play slim tapered D-profile having 22 frets.

But…Don’t/Never Solder on to a Closed Circle!…Because…If a very strong DC Electric Current Reaches your Axe…It Could…Kill/Maim!..With a AC Current you may if you’re lucky just get your fingers burnt!…You’ve just got to have a Break Somewhere!..So that in The Event of an Electrical Overload!..The Excessive Load can..Drain Itself off!…It’s an Electrical Safety Precaution!…Just like a Fuse!
In 1947, Jerry Wexler, a writer for Billboard Magazine described African American music as ‘Rhythm and Blues’ and its appeal was spreading fast and wide helped by the popularity of the radio DJ. People across the states would tune in to their favourite stations to hear the music they loved. Whether or not the song was performed by black or white musicians became irrelevant.

Russell is not only one of the hardest working technicians in Dallas but also a classically trained guitarist with a degree in classical guitar performance from SMU. To supplement his income playing classical guitar, he joined the Brook Mays team before finding a home at Charley's Guitar Shop. "Having a background as a player helps with cutting through the issue," he says. "I think the real part of guitar repair is being able to observe what's going on with the guitar but also understanding what the player is going through."


Before we begin, it should be pointed out that some time ago Guitar Player presented the history of Teisco, based on information painstakingly translated from a Japanese article penned by Mr. Hiroyuki Noguchi of Japan’s Rittor Music, editor of the Guitar Graphic book series. Unfortunately, the article used for reference was an older piece which has subsequently been totally revised and corrected by Mr. Noguchi based on later interviews with principals in the Teisco company. Some of the chronology in the GP story is inaccurate. What follows here is the latest and most accurate information on Teisco (in regards to company history), confirmed in repeated direct communications with Mr. Noguchi in Japan. This information also supersedes some incorrect facts in my own essay on Teisco Del Rey Spectrum 5 guitars in the first issue of Vintage Guitar Classics.

McCarthy's probably one of the toughest guitar masters on this list. His craftsman's hands know not only how to help your instrument make magic again but also (we assume) how to put you in an arm or leg lock and make you scream "Uncle" if you mouth off too much about your guitar's condition. It's probably why guitar tough guys like Zakk Wylde of Ozzy Osborne and Black Label Society, Izzy Stradlin of Guns 'n' Roses and Jason Newsted of Metallica gravitate toward his repair shop. (Not to mention the guys of Motorhead). They know they're dealing with a true master.
Compression: A "limiter" is envisioned as a circuit which prevents the output signal from exceeding a certain limit. If it did this by clipping, it would cause distortion, but if it can do it cleanly by just progressively reducing the amplification of the incoming signal, then it may properly be called a compressor. A compressor reduces the overall dynamic range by "compressing" the gain of high amplitude signals while maintaining the design gain for lower amplitude signals.

Durability: Unlike individual stompboxes where you might use some sparingly, since your multi-effects unit contains all your effects you’ll be using it frequently. As such, it’s important that the build quality is up to par. This is where brand reputation comes into play as well, since you want the brand to stand behind their product in case anything bad happens. Rest assured the pedals we recommend in this guide are all from very reputable manufacturers with long histories of good customer support.
You will agree with us that the journey to the Canaan land of guitar mastery isn’t always one with bed of roses. Rather, it seem very daunting, especially with so many different types, styles, shapes and sizes in the marketplace—all craving for the bulging eyes of your wallet. But as with anything, the options before you can become clearer if only you can endeavour to filter out the unwanted options—that is, those that aren’t compatible with your immediate needs.
The cost: The original G&L scheme calls for alternate pot values, but the project here uses the 500K pots found in most humbucker guitars, so all you need are wire, solder, and a few capacitors. On a three-knob guitar, you wind up with one master volume control and two master tone controls, but you sacrifice individual volume controls for each pickup.On a four-knob guitar, you still have independent volume controls, but you lose the independent tone controls.
If, like me, you're a complete and utter sucker for watching musicians strip their songs down to the barest essentials and perform them with minimal accompaniment, then you're going to lose your mind over the stripped down, guitar version of "Wildest Dreams" that Taylor Swift has just dropped from her acoustic session at the Grammy Museum Sessions last year. Performing the hopelessly dreamy song with just her voice and her electric guitar, the performance is jaw droppingly good and the song honestly sounds even better than it does on the studio track from 1989.
A functionally solid-body electric guitar was designed and built in 1940 by Les Paul from an Epiphone acoustic archtop. His "log guitar" (so called because it consisted of a simple 4x4 wood post with a neck attached to it and homemade pickups and hardware, with two detachable Epiphone hollow-body halves attached to the sides for appearance only) shares nothing in design or hardware with the solid-body Gibson Les Paul introduced in 1952. However, the feedback associated with hollow-bodied electric guitars was understood long before Paul's "log" was created in 1940; Gage Brewer's Ro-Pat-In of 1932 had a top so heavily reinforced that it essentially functioned as a solid-body instrument.[2] In 1945, Richard D. Bourgerie made an electric guitar pickup and amplifier for professional guitar player George Barnes. Bourgerie worked through World War II at Howard Radio Company, making electronic equipment for the American military. Barnes showed the result to Les Paul, who then arranged for Bourgerie to have one made for him.
×