In my own (first) project guitar, I did not know quite what to expect, so I built it with HSH pickups and two complete signal paths. The humbucking path uses 500k pots and an 0.047 cap; the single coil path uses 250K pots and a 0.022 cap. I did this with stacked, concentric CTS 250K/500K pots and an on/on toggle switch, all within the minimal confines of a standard Telecaster control plate. I created a custom 5-way selector switch to isolate the single-coil wiring from the humbucking combinations, but in the end when I flip the switch I opted for just the stand-alone single coil for the warmest sound. As I said above, the tapped humbuckers just didn't compare. This project is a work in progress; I hope this helps you find your own path.
Fret gauge might have a bigger impact on playing feel than on tone for many guitarists. Wider frets are often attributed a smoother, more buttery playing feel, which also makes it easier to bend strings. Ease of bending is also enhanced by taller frets, whether wide or narrow. Narrow frets shouldn’t be too hard to bend on, unless they are badly worn down, and they also leave a little more finger room on the fretboard—particularly in the higher positions— which might suit some players better.
And “tear” into them so like to do! My most recent “nightmare” was with such a simple thing as a fret “grind and polish” totally gone haywire! This particular repairman was nice enough, but broke so many things on my guitar just as a result of doing a fret job; he had it for another month after, and still could correct his mistakes! I final had to have the guitar literally “rescued” by the actual craftsman who made the guitar so it could finally be set straight again! It turned out that much as I had suspected, the repair guy wanted to see what made my guitar “tick”, so he unnecessarily tore it apart, but couldn’t properly put it back together again! He even broke 2 pickups by turning them too tightly as he lowered them!! Very costly errors, to be sure!
Fender Kingman "C" Custom Shop Acoustic/electric in Fiesta Red, 1 of 150 worldwide. This was a limited production that came out of the custom shop in Hartford, CT. Has a Fishman pickup. Not a nick, ding or blemish will you find on this guitar, almost museum quality. Comes with original Fender case(perfect shape), Certificate of authenticity and other paperwork and allen wrench. Ships to the US only.
It comes in lots of different colors, has a great quality at a bargain price. The HSS combination of this guitar is capable of playing a wide range of tones and sounds. It has a solid body and is quite comfortable to play. It has a Tremolo Bridge, which is not the best in the market but works quite well. Then there are tuners, which are also good enough.
You can think of these pedals like modulation effects that change nothing but the timing. They split up the signal in the same way, but time-based effects don’t usually make any major changes to the copied signal. Instead, they hold it back by a certain length of time before mixing it back in. This makes a few different varieties of pedal possible:
There are several good reasons why you might want to wire your Strat pickups in series. If you want more volume and midrange out of your pickups, the parallel/series switching may be the perfect option. As I mentioned, parallel wiring of two pickups is what you are used to hearing from a Strat. Parallel wiring adds transparency and clarity to the tone.
Judging by many of my last few years guitar purchases (on Ebay and elsewhere), I’m the kind of a person who seems to think he’s the kind of a person who likes guitars with a lot of knobs and switches. I’ve bought several multi-pickup guitars. Old ones, new ones, new ones made to look like old ones (not those stupid “relic-ed” ones, though…I’m an idiot, but I’m not stupid). Yet, as I look at the keepers in my collection, I’ve only kept one guitar with more than four knobs, and none with more than two pickups. Odd.
Yamaha F-310 Acoustic Dreadnought guitar in very good-excellent used condition no cracks or issues it looks great and the neck angle is excellent as well so as a result this guitar plays well with good fingerboard action with plenty of room on the saddle to lower action even more in future years if ever needed. Frets look good at 90-% with no ruts on fingerboard noted, truss rod is working fine, nut is 1-11/16ths. Yamaha specs (all of the F310 are made like this). It has 20 frets and a slim taper neck,The top is spruce, laminated, with natural finish. The sides and back are made of Meranti Indonesian Mahogany type wood , fingerboard and bridge are made Indian Rosewood, and the neck is of Nato. It's a full dreadnought guitar style, and just looks great.this one is in exceptional used condition better than average. Sound is good with nice volume and its tone is getting mature,,nice tone. No Cracks no issues no repairs and looks to have a bone nut and saddle this helps it have such a mature natural tone, Its sounds better than other F310’s Ive played I like this guitar and its price is right. any questions or to buy this guitar contact Joe at: JVGuitars@gmail.com .
Treble is really a form of gain boost that must be considered while gain-staging our signal path. With good tone, a note should ring like a bell, not slaughter like a machete, and that is accomplished by shaving some attack off the waveform and rounding off the frequency response. A bit off rollback on the tone knob takes you into the ballpark, along with your amp settings (I have a dedicated treble-cut on my AC30 that is necessary to tame my telecaster). Once I am in the ballpark, I use the volume knob to fine tune, and personally I tend to let it be from there, relying on a gain-boost pedal to lift my sound when necessary without altering the tone.
Solid body and Hollow are just two of the electric guitar types. In many ways, the Semi-Hollow Body guitar is synonymous with Gibson’s ES series from 1936. There have been many variants produced by Gibson itself, as well as copies built by other companies, but they all hark back to this original design. Even though Rickenbacker first released the Semi-Hollow guitar, the ES-335 is now the mainstay in the world of guitar.
There are literally hundreds of potential models we could show you, including a wide range from Martin themselves. But, as an example, we’ve chosen to share this rather attractive number called the Martin 00-18V. This guitar is a great demonstration of the top end of the price range, and features a host of show-stopping additions. Martin has great pedigree in the world of acoustic guitars – more on that later – and the Songwriter Deluxe is a great yardstick against which other dreadnoughts can be measured.
At £499, the MBC-1 is designed to hit a completely different price point to the Muse genius's full-fat Manson models, and although still designed by both Matt and Hugh, it's made in Indonesia by guitar-making giant Cort. Price aside, a quick strum lets you know this is a Manson through and through: it rings like a bell, the sort of acoustic response you'd expect from a quality guitar, but not always at this price. In style, the MBC-1 is a pretty accurate repro of the instruments used by Matt. That big upper shoulder won't be to everyone's taste, but in playing position, it's not only lightweight (3.52kg) but with forearm and ribcage contours, it fits like a glove. And the bolt-on maple neck feels superb, too, with a deep C profile and sloping shoulders that tell your hand it's thinner in depth than it actually is. Unusual at this price, too, is the compound radius fingerboard, which flattens out as you move up the neck; with tidy jumbo - but not over-tall - frets, it's a fast, fluid player, as well, which makes it one of the best electric guitars for hard-rock players. Pickup-wise, we have a fairly hot Alnico-powered humbucker at the bridge and a single coil at the neck. Along with a master volume, tone and three-way pickup selector, the upper shoulder also holds a kill button for stutter effects.
Description: Guitar Type: Acoustic/Electric - Body: Mahogany - Body Size: Dreadnought - Top Wood: Engelmann Spruce - Back: Bubinga (African Rosewood) - Figured - Sides: Bubinga (African Rosewood) - Figured - Neck Wood: Mahogany - Neck Attachment: Set - Neck Construction: 1 Piece - Fingerboard: Rosewood - Binding: Ivory - Frets: 20 - Inlay: Mother Of Pearl - Dot - # of Strings: 6 - Bridge Construction: Rosewood - Cutaway: Single - Soundhole: Round (Traditional) - Rosette: Mother Of Pearl - Hardware: Diecast, Gold, Grover Tuners - String Instrument Finish: Natural
This company really does nothing for me. Hideous designs, cumbersome shaped guitars and the fact that they keep milking dime bags name just makes me feel like they don't have much else. There are definitely worse brands out there like first act and daisy rock (shudders) but I've always thought dean just always sucked as a metal guitar company and b.c. rich isn't to far behind them in my opinion.
This Yamaha Pacifica features a Strat sound that is very good, especially since the humbucker can be tuned into a single pickup by lifting up on the tone control. Like with every other strat, it has a five-way switch which allows the player to select the bridge pickup, the bridge+middle pickups, the middle pickup, the middle+neck pickups, or just the neck alone. In the event that you are tired of the strat sound and you would like to return to Led Zeppelin, simply flip to the humbucker and get set to go!
I have inherited a heater "H300N" acoustic guitar but I can't find any info on it. The most I could find is that it was from the L. D. Heater Music Company that was based out of Beaverton, Oregon. They were best known for being a distributer of Lyle Guitars. Can anyone else offer additional information or where to find it? It's a bueatiful guitar and I want to know more info before I give it to my nephew or sell it.
Amongst the best guitar brands in India for acoustic guitars, Martin is one that stands out. Martin is one of the best known brands for its steel-string guitars. It is a leading manufacturer of flat top guitars which produce top notch sound quality. However, the company is best known for their signature dreadnought acoustic guitar with X-bracing. It is truly one of the best guitar brands for some of the best quality guitars in the market.
MusicPCB.com – offers PCB projects to build guitar and bass effects, and synth modules. All PCBs are professionally manufactured, and include soldermask, a silkscreened component legend, and plated through holes and pads. They are designed to be easy to build, provide simple and clean wiring, to work well with your other pedals, modules, and instruments, and most of all to sound great and provide sounds and features not available in commercial designs. Each PCB comes with a PDF document with wiring diagram, schematic, build notes, and large modding sections with details on how to perform a variety of mods to tailor the design to your needs/taste.
If you’re looking for a solid start on how you will sound without settling for a tube amplifier due to its price, maintenance and back breaking weight to carry around. The Marshall MG30FX combo amp is surely one of the best out there on capturing iconic sounds, as well as the legendary Marshall tones that other brand of amplifiers frequently emulates, adding it to their bank of amp models.
In late 1966, Peter Green had the job of replacing Eric Clapton in John Mayall's Bluesbreakers. Mayall told his producer, "He might not be better [than Clapton] now. But you wait… he's going to be the best." Soon, with the original Fleetwood Mac, he was Britain's most progressive blues guitarist, with a Chicago-informed aggression heightened by the melodic adventure on albums like 1969's Then Play On. Green soon entered a dark age of mental and health problems, returning in the Nineties with more subdued but recognizable gifts.
This is a right handed 2018 Gibson Custom Shop Explorer, Extra/Elbow Cut, with a heavy aged relicing, Natural Finish, Gold plated Nickel hardware. This model is patterned after the 1958 Explorer owned by Eric Clapton. It is brand new with OHSC, COA, and all paperwork/tags. The weight is light at only 7 lbs, 12 oz. This is only one of a limited run of 5 in the Natural Finish. I also have the same guitar in Cherry finish, one of only 5 in the Cherry finish.
A pedal itself can have an effects loop, but the most commonly used place is on the amplifier itself. You'll see on most amps (but not all) some form of output labeled as Effects Send or Preamp Out accompanied by an input labeled Effects Return or Power Amp In, respectively. Both sets of outputs and inputs refer to the effects loop that you can add between the preamplifier and the power amp section of your amplifier.
The name has a long and involved history that is interwoven with that of the resonator guitar. Originally coined by the Dopyera brothers when they formed the Dobro Manufacturing Company, in time it came to commonly mean a resonator guitar, or specifically one with a single inverted resonator. This particular design was introduced by the Dopyeras’ new company, in competition to the already patented Tricone and biscuit designs owned and produced by the National String Instrument Corporation.
Loop-based guitar plugins are slowly moving to the point of obscurity as virtual instrument technology is getting to the point where even string instruments can sound out-of-this-world good and blossom with character. But there still exists some gems out there such as Acoustic Revolutions, which updated to volume two as recently as 2015, doubling the number of loops.
Joining the J-1 (and J-2) were the sunburst J-3 and J-5. These had no real relationship to the earlier, very fancy J-5 mini Les Paul. These both had somewhat larger bodies with narrower waists and had ever-so-slightly offset double cutaways, with the upper horn just slightly extended. The bolt-on necks were similar to the J-1, with an open-book head and large dots, with added binding. The J-3 had a single rectangular bridge pickup, while the J-5 had a pair of pickups and a chicken-beak selector on the upper horn. The pickguards covered just the area under the pickups; controls were mounted on the top, volume and tone for the J-3 and three controls on the J-5.
The honest truth lies with the listener’s ear and capability to identify a sound with an individual player. B.B. King was known for his tone and only later revealed his secret mentioned above. It wasn’t even really a secret; it was more of a physical shortcut that allowed him to express himself. You should choose what feels and sounds best for your own musical expression.
The electric guitar was essentially born in 1929—long before the advent of rock and roll music. The first commercially advertised electric guitar was offered that year by the Stromberg-Voisinet company of Chicago, though it was not a smash hit. The first commercially successful electric, Rickenbacker’s “Frying Pan” guitar, didn’t kick off rock ’n’ roll yet either, but it did inspire competitors to jump into the electric guitar market. Invented in 1931, the Frying Pan had an electromagnetic pickup made out of a pair of horseshoe magnets placed end-to-end to create an oval around the guitar’s strings, with a coil placed underneath the strings. The pickup, a device that converts the strings’ vibrations into electrical signals that can be amplified, was bulky and unattractive, but it worked. The commercial version of the Frying Pan was a hollow cast-aluminum lap-steel guitar, and wasn’t an immediate hit beyond some Hawaiian, country, and blues musicians. It differs from the traditional Spanish-style guitar in that it is played horizontally, on a stand or in the player’s lap, and has a sliding steel bar that can be moved along the frets for a gliding effect.
You may hear many guitarists or repairman talk about pots. What are pots? The word “pot” is short for potentiometer. A potentiometer is a simple electronic device that adjusts the flow of electric current. Most pots are basically glorified resistors. There are two outer lugs that carry the voltage to and from the pickups. The middle lug is a “swipe” lug that resists the voltage. When the knob is turned, the swipe resists more or less voltage allowing the volume to decrease or increase. Both volume and tone knobs are pots. The only difference between these two pots is that the tone pot has a capacitor soldered to the ground lug. The capacitor short-circuits the high frequencies disallowing them from reaching the output jack and eventually the amp. Your guitar will sound less trebly the smaller the resistance of the tone pot before the capacitor. For a more technical description of a capacitor, see the electric guitar capacitor page.
An effects unit is also called an "effect box", "effects device", "effects processor" or simply "effects". In audio engineer parlance, a signal without effects is "dry" and an effect-processed signal is "wet". The abbreviation "F/X" or "FX" is sometimes used. A pedal-style unit may be called a "stomp box", "stompbox", "effects pedal" or "pedal". A musician bringing many pedals to a live show or recording session often mounts the pedals on a guitar pedalboard, to reduce set-up and tear-down time and, for pedalboards with lids, protect the pedals during transportation. When a musician has multiple effects in a rack mounted road case, this case may be called an "effects rack" or "rig". When rackmounted effects are mounted in a roadcase, this also speeds up a musician's set-up and tear-down time, because all of the effects can be connected together inside the rack case and all of the units can be plugged into a powerbar.
Johnny Marr: I'd already played a couple of shows before that with a couple of bands. I'd been in a couple of bands before I met Andy, even though I was fourteen or fifteen at the time. We met in school, Andy and I. I'd been playing in these little kid's kinds of bands at twelve and thirteen. When I got to fourteen and fifteen, I got invited to play in a couple of bands with much older guys.
Flanging is the strongest of the standard modulation effects. The feedback control increases the depth of the 'comb filtering' produced when a delayed signal is added back to itself. Because it is such a distinctive effect, it is best used sparingly, though it can also be used to process a reverb send to add a more subtle complexity to the reverbed sound.
Strings produce sound in the guitar. In electric guitars, because there are no holes, the vibration is passed to a pickup which senses the vibration of the strings passes the signal on to the guitar amplifier. There are two types of strings for electric guitars, light and heavy gauge. Lighter ones are easier to play and allow easy bending of notes, but they are more likely to break and produce less volume. On the other side, heavier ones produce high volume but are hard to play and require more finger pressure to bend notes.
The fully hollow body electric guitar is almost always a finely crafted work of art. These instruments are a throw back to the days of hand shaped acoustic instruments of yesteryear. The hand carved archtops and backs are designed to take advantage of pure acoustic detail, such as resonance and tone, while the electric aspect allows the performer to be amplified. A pure traditionalist could ask for nothing better tone wise, but must contend with other aspects of these incredibly resonant instruments.
In the ever-changing world of jazz music, you shouldn’t be surprised to hear of some big changes to the jazz guitar market either! To reflect this we’ve tweaked our chart, removing a couple of models such as the Ibanez AF95FB and the D’Angelico EXL101, and adding five new six-strings. These comprise the faithfully reproduced Epiphone Masterbilt Zenith Classic and the thinbody LH-302T from The Loar. In the semi-hollow section, we added the Ibanez AM93AYS Artcore Expressionist and the beautiful Hagstrom Tremar Viking Deluxe, while the solid-body section saw the arrival of Fender’s Classic Player Jazzmaster Special.
Most people think of Roy Orbison as the super-smooth crooner who sang songs like “Crying,” “In Dreams” and “Only the Lonely.” But Orbison was also a wicked guitar player, who ripped out several impressive solos on early Sun Records singles like “Ooby Dooby.” In fact, Sun owner Sam Phillips was more impressed with Orbison’s guitar playing than his singing during the early days of the rocker’s career.
Jimi Hendrix: Right-Handed vintage white body flipped upsidedown for left-handed use with an oval profile maple-cap neck. The controls and electrics are vintage-modern to ensure stability. The guitar is strung upside down with the strap button on the lower horn, the backwards 68 thick black CBS headstock decal is so that—in front of a mirror—the player sees the guitar as it would appear if Jimi Hendrix played it. As well as this upside-down lefty Strat for right-handed players, Fender also made four exact copies of the Vintage white Stratocaster Hendrix used in many performances, the most famous being Woodstock (1969).
Are you in earnest need of a guitar and do you want to buy that right now. Well, if the answer to this question is yes, then you will have to stop and think for a while before you actually make the investment. This is because of the fact that buying a guitar is an expensive investment, so you must to be quick to arrive at a decision. Now you should be asking yourself some pretty interesting questions before you buy a guitar so that you do not have to regret later on in any way.
The one-man band has been elevated to new heights lately, but behind the loopers and pads, there usually lies an unremarkable musician. Australian songwriter Tash Sultana brings a widescreen pizazz to the format. Her sprawling, expertly weighted amalgamations of hip hop beats, soothing synth pads and foil-wrapped shimmering tones, give way to surprising bursts of scuzzy, shred-y solos, creating an exhilarating contrast to her breathy vocals. A talent that doesn’t decay with the delay pedal.
Volume pedals are volume potientiometers set into a rocking foot treadle, so that the volume of the bass guitar can be changed by the foot. Compression pedals affect the dynamics (volume levels) of a bass signal by subtly increasing the volume of quiet notes and reducing the volume of loud notes, which smooths out or "compresses" the overall sound. Limiters, which are similar to compressors, prevent the upper volume levels (peaks) of notes from getting too loud, which can damage speakers. Noise gates remove hums and hisses that occur with distortion pedals, vintage pedals, and some electric basses.
Flanger pedals are based on a studio sound made when two tapes were mixed together and one was delayed. What this does is add shifting harmonic content to your signal, as well as modulation. Flanging is a very distinct effect that adds a unique whoosh or airplane-like sound. Used with restraint, the flanger adds an interesting dimension to your sound, almost synthesizer-like sound. Used at extreme settings, flangers will over take the tone and bring a solo to completely different sonic level.
alright i think we all need to stop hating on john mayer. I don't think that he really would even call himself one of the best guitarists of all time, he's obviously not far enough into his career to be criticized about this stuff. But i love him, and he eventually will make it on this list. Oh, and for all you who say he sucks and whatever, if he is so bad then why has he played with so many of the people who actually should deserve to be on this list?
A good guitar builder can pick materials that provide a predictable result. The process of making a
Amps available in ’61 included the large HG-8 (recommended for use with the EG-TW and Harp Guitar), the Amp-75C, Amp-73C, Amp-72A, Amp-72B, Amp-72C, Amp-71A, Amp-71B, Amp-71C, Amp-30, Amp-4C, Amp-15 and Amp-86 bass amp. These came in a varity of shapes, mostly with either a single color covering with a tweed grillcloth, or the two-tone Amp-30 or the two-tone Amp-15 with a cross-shaped grillcloth area. All had the Swan-S logo. These were most likely still all tube amps at this point in time.
The best guitars? Look at what the best players use. Certainly Gibson and Fender are in the mix, but these are typically priceless, early production or highly customized one-off units. If you want something more or less off the shelf that is in the same range of build, tone and feel quality look at the following (BTW, you can't get these at Guitar Center, which is probably why they haven't been mentioned yet):
You have a 2 band EQ as well as independent gain and master controls as well as a headphone/line out jack for either silent practice or recording directly to your audio interface. There’s 10 watts of solid state power flying out of the 6.5" speaker so you’re covered for smaller gigs and practice sessions whilst the classic VOX grille cloth and chicken head knobs provide that unmistakeable VOX look. A fantastic amplifier that will provide you with lush tone and typical VOX reliability – you can’t argue with that for under £70.
Hi everyone! I have a quick question regarding string action. I have just gotten my 2003 Standard set up a few months ago, but I am having trouble with how low the action is; strings slip off of my fingers during bending now. If I just turn the screws on the Tune-O-Matic bridge to heighten the action a little bit, without touching or adjusting the truss rod, individual saddles, or tailpiece, will that screw up my intonation?
Depending on whether you play rhythm or lead guitar, you will want more or less treble cut. One of the secrets to a two guitar band lies in the tonal differences achieved between the guitars that stop them from bleeding together. Part of this is inherent in the different instruments and amps used by the two guitarists (humbucker vs single-coil pckups being the greatest differentiator imo, as well as discerning use of the pick-up selector switch), but the contrast must also be attended to on the fly, and here the tone knob, along with the useful volume knob help the two guitarists from stepping on each other’s tonal feet while mixing their notes together.
An excerpt: “First let us dispel the popular, but completely wrong belief that ‘any guitar will do for learning to play.’ Your first guitar should be carefully chosen to be fairly easy to play and tune. It should also be versatile enough for you to be able to play different kinds of music on it. For this reason, and to avoid the complications and expense of an amplifier, an ‘acoustic’ (un-amplified) guitar is recommended.”
Fender released the first successful solidbody electric guitar, the Broadcaster, in 1950. (Remember, the original Esquires were problematic.) Gibson produced the first Les Paul 24 months later. And a mere six years after that, a small run of sunburst Les Pauls flowed out of Gibson’s Kalamazoo, Michigan factory. Originally just another instrument, those Les Pauls now occupy a mythic status in the minds of guitarists and collectors everywhere. The instruments, along with a small handful of Fender Stratocasters and examples from one or two other manufacturers from roughly the same era, represent the Holy Grail in guitar tones.
Who are you to state that Taylor guitars are among the best in the world? Are you from California? I don't and many other don't feel that way. Taylor just does not have the sound of other fine acoustical guitars. I'm not putting Taylor down. It's a well built acoustic but I don't quite like the sound of them. That's a biased and very bold statement you made about Taylor and it's not true. There are so many great acoustic guitar builders around this planet that do build superb guitars. Please, lets not put a Californian Company biasedly on top of everything on the planet. Can we do this please? I apologize for this email but what you stated is so unfair for all of the others guitar companies that build outstanding guitars, worldwide.
SOLD OUT ! We are VERY pleased to present a very special example Alvarez Yairi Classical guitar . The condition of this high end instrument is excellent plus and this guitar is simply wonderful. This is hand built example by The Kazou Yairi himself, Japanese Master Luthier. For those of you not familiar with the Premier Japanese Master Luthier Kazou Yairi and his masterfuly built instruments you may enjoy this vidio introduction to YAIRI GUITARS http://www.youtube.com/watch?v=NPRyLPouYZM The model is CY116 and is a very high-end professional guitar and is in excellent Plus condition. Only the highest grade woods used as you can see ...choice AAA Flamed-Quilted and is 3-dimensional depth is a work of art as you can see by the pictures. This guitar plays and sound AMAZING and is truly inspirational. This guitar shows very little fret wear. There are just a few minor nicks or scratches which is normal wear for a guitar of this vintage that has been lovingly played. This one is a one owner adult owned guitar and comes with its high quality custom hard shell case too. General Specs: Alvarez Yairi CY116 Classical Acoustic Guitar The CY116's Solid Cedar Top is adorned by an elaborate wooden mosaic rosette. Burled Maple Back/Sides give this classical amazing clarity and warmth like the fiery Andalusian plains that inspired the music that this guitar was born to perform. With room-filling projection, the CY116 is a guaranteed conversation starter. You hear it in the elegant pacing of a classical air. You see it in the vivid charm of a folk dance. Specs: Burled Mahogany Back/Sides Solid Cedar Top Mahogany Neck Ebony Fingerboard Scale: 25 1/2" (650mm) Width at Nut: 2" (51mm) Rosewood Bridge Ivory Body Binding Wooden Mosaic Rosette Gold Vintage Open-Style Tuning Machines .
PLUG THE PORES What you use to prep the body for paint depends on the chosen finish that you will go with. For a solid color finish you will want to fill any of the pores with a wood filler or Bondo glazing putty. I prefer Bondo because it dries quickly and sands smooth. Use one of those plastic speaders that you can get for mud at a paint or hardware store and press the filler firmly into the pores and gaps in the wood. Cut diagonaly accross and against the grain to fill the pores and gaps better. Use a sanding block and a 220 grit paper and after the filler dries to ensure an even flat surface. Only use your hands to lightly sand on the rounded edges or hard to reah areas of the guitar. The roundness of your fingertips can cause depressions in the woods surface so stick with the sanding block on the flat areas. Inspect the surface to see if any pores or gaps remain and repeat the steps if needed. Then clean the surface with a tack cloth to remove any dust.
Electric guitar design and construction vary greatly in the shape of the body and the configuration of the neck, bridge, and pickups. Guitars may have a fixed bridge or a spring-loaded hinged bridge, which lets players "bend" the pitch of notes or chords up or down, or perform vibrato effects. The sound of an electric guitar can be modified by new playing techniques such as string bending, tapping, and hammering-on, using audio feedback, or slide guitar playing. There are several types of electric guitar, including: the solid-body guitar; various types of hollow-body guitars; the six-string guitar (the most common type), which is usually tuned E, A, D, G, B, E, from lowest to highest strings; the seven-string guitar, which typically adds a low B string below the low E; and the twelve-string guitar, which has six pairs of strings.