When you start to look for that great beginner's electric guitar, focus on an instrument with good-quality wood and reasonable workmanship. That's the most commonly accepted method of choosing a low-cost electric guitar for a beginner. Guitar manufacturers tend to cut corners with cheaper guitars by using, for instance, cheaper pickups and hardware. But for the guitarist who gets more serious about playing, these are all upgradeable parts that can be swapped out for higher-quality parts. So begin with a good-quality wooden frame and upgrade as time and money allow.

I started out doing pretty much what I do now on an acoustic and transferred it to electric when I was able to get a paper route and buy a crappy red electric guitar. I knew the value of working stripped down and I still do, although in this day and age I've made a lot of records with different sounds. I must say I really love what technology can afford you.
I have a Norma single pickup electric guitar with 1 volume and the 3 position tone switch. Someone tried to repair the wiring (w/o soldering) so it didn’t work when I found it. I did some simple wiring/soldering and got it working and the pickup sounds great but I cant figure how to wire it so the tone selector works. Any help or a diagram would be great.
The Firebird did have some other unique features such as its banjo style tuners and mini humbuckers that produced a different sound than the full humbucker pickups Gibson typically offered.  Many notable players preferred the Firebird: Mick Taylor from the Rolling Stones used it on the album Exile on Main St.  Allen Collins would also use this axe on stage with Skynyrd alongside his Explorers.  The great Texan blues guitarist Johnny Winter was known for playing slide on his 1963 Firebird to great effect.  Dave Grohl, of Nirvana and Foo Fighters fame, used his white Firebird to create a modern rock sound.
A guitar needs to receive regular maintenance if it is to keep its intended levels of playability and sound quality. Caring for a guitar involves a process known as a setup. This describes a group of fine-tuning procedures that work together to bring the instrument to its highest potential. The cost of a guitar setup is often well worth the value of the service. New strings will be added, their height adjusted, intonation will be set, and the neck may be adjusted to allow for the proper amount of relief in the wood. Most guitars need to be setup at least once a year to account for swelling of wood and shifting of parts that are caused by changes in humidity. Guitar setup cost is usually around $50, but can fluctuate wildly depending on what adjustments are needed for your specific instrument.
An utterly odd topic would be a discussion of woods for a certain tone. Wood does no magic to the tone. It has properties which might change the resonant behavior of a guitar body. But, that it does by some very course parameters, say stiffness and specific weight. Of very same importance is the shape of the plank which is referred to as “the body”. Stiffness, weight and shape work all together.
The simplest way to explain modulation effects is that they make a copy of the original signal, modify the copy in some way, and then mix the original and the copy back together. The result is sort of like a pitch-shift taken to the next level, where instead of simply adding new notes or varying the fundamental, they can create entirely new sounds altogether. Here are the usual suspects of modulation effects:

Schecter's C-6 Plus belongs to their basic line of guitars. It features their own Super Strat body shape which is finished with a glossy charcoal burst finish. The tonewood of choice for this build is basswood, an inexpensively sourced wood, which is what allows such a nice guitar to be priced at this range. There are some aspects of basswood which work great with guitars designed for heavier genres, and on top of that, it is light weight. Don't take this for granted since it'll be hanging on your shoulders and back for long periods of time.
The actual key that this song was written in is Bb (B flat) and can be a bit difficult for beginners; I prefer using a capo for this song and playing it in the Key of C. Using the capo to play this song doesn’t change how the song sounds, but it makes playing the song a lot easier. Using your capo on the third fret, you chord progression will look like C – G – Am (A minor) – F.
When you are shopping for effects pedals, a good feature to look for is true bypass. Your overall signal path is vulnerable to noise and impurities introduced by the circuitry of anything between your guitar and your output device (such as your amplifier/speaker). Pedals without true bypass, or ones with buffered circuitry, will contribute to some signal degradation as your signal passes along the path because the signal is routed directly through the pedal circuitry. Pedals that have true bypass direct your signal around the pedal’s circuitry, or bypass it, when you switch the pedal off, thereby maintaining the integrity and cleanliness of the signal. Your amplified guitar will sound more robust as a result and you won’t be required to crank up your volume as much to compensate for lost signal. The only disadvantage of pedals with true bypass is that sometimes, when you're playing with distorted or high-gain amplifier tones, you might notice switching noise when you switch the pedal off and on.
These two components work in tandem to influence tone and playability. The bridge is mounted to the lower portion of the guitar body. The strings are routed over it before terminating on the body or on a tailpiece. Bridges are designed to compensate for varying string lengths, gauges, and metals, ensuring that the strings remain in tune with each other. Bridges usually allow adjustment of the string's length to bring each string into tune along the entire length of the fretboard. This process is called intonation, and is an important part of setting up a guitar for optimal performance. Some bridges permit string height adjustments that affect the the ease with which the strings can be fretted, and is often referred to as the guitar's "action."
Three recording sessions between 1936 and 1937 produced 29 songs, including the verifiable classics “(I Believe I’ll) Dust My Broom,” “Sweet Home Chicago,’” “Walkin’ Blues,” “Love in Vain” and “Crossroad Blues.” His popularization of cut boogie patterns presaged electric Chicago blues and rock and roll, while his fretted and slide guitar licks are so timeless that they still show up in contemporary music.
The Yamaha APXT2 is a 3/4 size version of the world's best-selling acoustic-electric guitar, the APX500III. This well-constructed, compact guitar makes a great companion when you're on the road. The APXT2 features an ART-based pickup system and Yamaha's proprietary tuner, offering great sensitivity and accuracy for quick tuning. The APX T2 also includes a gig bag.
In the second diagram, the two pickups are wired in series. The theory behind series wiring is that the ground wire of one pickup is connected to the hot wire of the other pickup. As a result, they become a kind of compound pickup, with one ground and one hot for both. When wired in series, the pickups combine their impedance (resistance) and the output is very high. If your Strat’s middle pickup is a reverse-wound/ reverse-polarity type (aka RWRP), you’ll get the same humbucking effect as you do when the pickups are wired in parallel—no changes there.
Electric guitar is still the most prominent instrument in rock music, and it’s a key component in many country, R&B, pop, and jazz groups. Every electric guitar player needs an amplifier because most electric guitars are barely audible without one. You’ll need one to play with other musicians, which is one of the most important ways to develop your musical skills. Because the amp is as important to a guitarist’s sound as the guitar, most teachers consider it essential to use an amp at least part of the time when you’re practicing. You can’t develop your own sound without spending some time experimenting with the controls on your amp and guitar.
Along with Taylor, C.F. Martin and Co. sets the mark for top-level American-made acoustic guitars. They’ve been around since 1833, and today they make most of their guitars in Nazareth, Pennsylvania. They use premium materials to get the best look and sound out of their guitars, but they’re also a leader in understanding the environmental impact of over-harvesting tonewoods.
This is something that a lot of people get wrong. Electric Guitars are much smaller than Steel-String Acoustic Guitars and Nylon String Classical Guitars, they can basically be used by most people, but you do need to consider the extra weight. An Electric Guitar can weigh 5-6 Kg which can be difficult for children to handle. We would normally recommend children be at least 13 years before they try an Electric Guitar, but this is a generalisation and some children (sometimes as young as 10) have been ok. Every child is different, and some children may be capable at a younger age, so if you consider your child to be quite strong for their age, then by all means go for an electric. We carry a broad range of sizes in our entry level range. The correct size is most accurately determined by the player’s height, age and in some cases gender. If you can tell us these three details we can give you a personal recommendation.
Distortion, overdrive, and fuzz can be produced by effects pedals, rackmounts, pre-amplifiers, power amplifiers (a potentially speaker-blowing approach), speakers and (since the 2000s) by digital amplifier modeling devices and audio software.[1][2] These effects are used with electric guitars, electric basses (fuzz bass), electronic keyboards, and more rarely as a special effect with vocals. While distortion is often created intentionally as a musical effect, musicians and sound engineers sometimes take steps to avoid distortion, particularly when using PA systems to amplify vocals or when playing back prerecorded music.

I kind of think what I do is like producing with my feet because I do a lot of that in my own shows. Particularly when I'm playing guitar with other bands, I'm always changing reverb [settings] and modulation types and the very sorts of things that [maybe no one else realizes what's going on], but it keeps me interested. I think because I come from a time before that was possible, it's a magical thing for me.
Prior to being acquired by Gibson back in 1957, Epiphone once competed with the most popular guitar brands in the market - including Gibson. These days, Epiphone is known for being the affordable sub-brand of Gibson, producing cost-effective alternatives to many of their premium guitars. Many experienced players today credit this brand for manufacturing their first ever instrument, and their popularity in the entry level market continue to soar high.
One type of "effect" I've thought would be useful to have in a multi-pedal, though I've not seen it, would be to have a configurable automatic gain control (level compression) which would be applied before a distortion effect, followed by a gain adjustment after the distortion which would undo some or all of the effect of the previous AGC. For example, things might be set up so that playing at a level of -20dBm would boost the signal by 21dB (clipping slightly) and then reduce volume by 20dB, while playing at -10dBm would boost by 12dB (clipping a bit more) and then reduce by 12dB. – supercat Apr 30 '13 at 22:01

Morning everyone, well it is here in UK anyway. Who can help with my find. It's a Dia Hummingbird labelled F 315 but no serial number. So from what I can find Dia was a brand used by Matsumoku but I can only see electrics under Dia brand when I search. However it looks identical to a Aria F315 Hummingbird on eBay USA at present, and identical to an Aria Pro II from the 1976 catalogue but labelled W 30 model I believe. I won't put a link on here in case I'm breaking rules. It has that weird aluminium compensated bridge and seriously, this one looks brand new with two tiny dings that would make it a second or an ex-demo if it was on sale. Action at low E 12th is about 2.7mm and about 1.8 at high e. It's in such good condition I began to question if in fact it is a 'knock off of a knock off' though why anyone would think that would work I can't guess. It is very very playable, and at first I wasn't keen on the tone though sustain is great (despite bridge) but I changed to heavier strings (13) with much improvement. I'm seeing a luthier friend next week who is finishing off work on a brilliant Terada FW 613 (D18 clone if you like), but I'm wondering whether to get him to replace the whole alloy bridge. I can do a couple of pics if anyone is interested. Any help in identification of maybe year (guessing 1976) and origin greatly appreciated. I think it's a keeper, but should I change that bridge ? Has anyone done similar on one of these compensated aluminium designs and what were results. Many thanks.
Solid state and modeling amps are great amps to use for practice sessions. As well to bring it for small gigs and recordings that require their services. That is the reason why it is really hard to tell which one is above and try to suggest that a particular amplifier is better than the other. Having an own thing is what really is important here, and besides if you really sound good. The gears you will be playing with will equally sound as great.
Regardless of what side anyone is on, when it comes to the tonewood debate, tonewood's relevancy is just a small part of a bigger discussion. Simply talking about guitar, sparks interest in guitar. This is and will always be a good thing. Any pursuit that expands one's creative and mental abilities can be regarded, in most cases, as a grand and noble thing. So, in arguing about tone wood, it's fanatical sides raging against each other, interest in the instrument they're picking apart will inevitably grow.
Ovation are relative newcomers to the world of vintage guitars, only launching their range at the 1967 NAMM show in Chicago. Ovation started as an off-shoot of founder Charles Kamen's work in the aviation field, studying vibration and resonances in helicopter blades. Whilst other respected American manufacturers relied heavily of quality nautral products and the artistry of their master luthiers, Ovation came very much from a science and engineering perspective: they used oscillographs to test existing instruments, and came up with the famous Ovation rounded back design, and suggested the use of a synthetic material, Lyrachord, claiming it to be more resonant that any wood.
We have covered pickups here before so rather than running over old ground I suggest you read that article to get an understanding of the different types of pickups an electric guitar uses and how they work in greater detail. For the purpose of this article, however, all sound starts with your pickups. Pickups are essentially magnets, generally 6 small magnets wrapped in a very fine copper wire (over 7000 times), and can be better described as magnetic wire coils.
In other words, it will slather the tone with raw dirt without affecting the core of the signal. A lot of people mistake fuzz pedals for distortions due to their more aggressive nature, but these beasts of old are definitely unique. One of the best examples of what a fuzz box sounds like is the Electro-Harmonix Big Muff Pi – a fuzz pedal whose circuitry gave birth to countless other models.
The size and power rating of the amp, as well as the size and type of the speakers within the cabinet, will have a significant impact on the recorded sound. Obviously, huge stacks will produce a very different sound from small combos. That said, many recording engineers have found that a small, low-powered amp cranked right up can sound more exciting than a big powerhouse. Even cheap transistor amps with tiny speakers can sound great in the right context. Don’t be precious and don’t rule anything out; it’s all about the end result!
Firstly these are both 'mic-level' or 'instrument-level' inputs (they carry very quiet signals) but hi-Z signals are more prone to interference. The lo-Z signal consists of the instrument's mono signal (hot) and it's inverted waveform (cold), the cables are twisted around one another such that any interfering signal generated in one is negated by the other (much the same as the way a humbucking pickup works).

It is a standard dreadnought with 26 frets. There are no electronics, no cutaway, and no fancy upgrades. It has a book matched sitka spruce top, rosewood fingerboard, adjustable rosewood bridge, cream colored plastic binding, rosewood back and sides, and a black inlaid headstock. The neck is not one piece and is made from presumably African mahogany. It has closed gold tone tuners, black beveled pick guard and some plain black line art for a rosette. This guitar is void of polyurethane and has a lacquer finish, so much the better.

Mikko, spot on. Even light wood has density, and there comes a point in solid body electric guitars where how dense any piece of wood is only makes a difference acoustically. The point you made about how a guitar feels when you're playing it is sound, though. Its weight and acoustic resonance will affect how you respond to it and how you attack it (same for neck thickness and profile), and that will account for the preference we have for one guitar over another of the same model.
I tried very hard to work with this book. And I think the author went to a lot of trouble to make the information presentable and understandable. But it didn't work for me. Today I made a second run at the book to see if I could make sense of it. I remain very disappointed. I am an electrical engineer, and perhaps that is my problem. The author must have created his own wiring diagram and components system which he understands well. But I don't. The basic problem is that he uses shades of gray (in lieu of color) to illustrate the circuitry and components. In the book it talks about colors, but all is shades of gray.
While electric bass players have used regular guitar amplifiers in large concerts since the 1960s, this is usually just for the higher register; a bass amp is still typically used for the low register, because regular guitar amps are only designed to go down to about 80 Hz. One of the reasons bassists split their signal into a bass amp and an electric guitar amp is because this arrangement enables them to overdrive the higher-register sound from the electric guitar amp, while retaining the deep bass tone from the bass amp. Naturally-produced overdrive on bass obtained by cranking a tube amplifier or solid-state preamplifier typically results in a loss of bass tone, because when pushed into overdrive, a note goes to the upper octave second harmonic.
Boss’ CE-1 Chorus Ensemble was the first of these types commercially available, and is the best remembered of the company’s now-archaic looking early range of die-cast metal pedals. The unit was an instant success when it hit the market in 1976, and was quickly snatched up by a range of major players. Andy Summers used the CE-1 with the Police in the late 1970s and early 1980s, and it’s probably most famously heard on the band’s big 1979 hit “Message In A Bottle,” though others made creative use of it too. Shortly after the Boss, Electro-Harmonix offered both its Memory Man Stereo Echo/Chorus—which featured a very good, spacious chorus setting that a lot of player’s loved—and smaller, stand-alone Small Clone chorus. Like the Small Stone phaser before it, the Small Clone had a softer, subtler sound than many of the chorus pedals that would soon flood the market, and it too was a huge hit. Kurt Cobain’s use of the pedal on “Smells Like Teen Spirit” and Chris Novoselic’s bass part on “Come As You Are” from Nirvana’s Nevermind album shows off how it can add a rich, moving, liquid texture to both clean and distorted parts. MXR, DOD and Ibanez all offered popular early IC-based analog chorus pedals, and today every major mass-manufacturer has a unit on the market.
For the hobbyist guitarist this is a great 'bang for the buck' investment. It has practice tools for the beginner but solid tones for the advanced guitarist. For home use, maybe even a garage band it's perfectly adequate. If I were a more serious musician doing gigs with high end audio going to the audience, I'd be investing more than a hundred bucks in my stage rig.
Jump up ^ "The first incontrovertible evidence of five-course instruments can be found in Miguel Fuenllana's Orphenica Lyre of 1554, which contains music for a vihuela de cinco ordenes. In the following year Juan Bermudo wrote in his Declaracion de Instrumentos Musicales: "We have seen a guitar in Spain with five courses of strings." Bermudo later mentions in the same book that "Guitars usually have four strings," which implies that the five-course guitar was of comparatively recent origin, and still something of an oddity". Tom and Mary Anne Evans Guitars: From the Renaissance to Rock. Paddington Press Ltd 1977 p.24
There are lots of adjustment points built into modern electric guitars. And unless you know what you're doing (and why), these adjustments can tempt you to mess around with your guitar and make things worse instead of better. With this book, you can avoid that trap. You'll find step-by-step instructions for setting up your guitar, replacing strings, changing string gauges, dealing with common electronics problems, and more.
The guitar, however, appears to be in better shape than the guitar maker. While in the past decade, sales of the electric guitar have fallen from 1.5 million to 1 million, according to the National Association of Music Merchants (NAMM) a total of 2.6 million guitars, including both acoustic and electric guitars, were sold in the U.S. last year, 300,000 more than in 2009.

Pitch-shifters work by slicing the incoming audio into extremely short sections (typically a few tens of milliseconds long) and then lengthening each section where the pitch is to be decreased, or shortening each section where the pitch is to be increased. Though cross-fading algorithms and other techniques are used to hide the splice points, most pitch-shifters tend to sound grainy or warbly when used to create large amounts of shift (a couple of semitones or more), though they can sound very natural when used to create subtle detuning effects, using shifts of a few cents. A refinement of the system, designed for use with monophonic sources, attempts to synchronise the splicing process with whole numbers of cycles of the input signal, which makes the whole thing sound a lot smoother but, as soon as you present these devices with chords or other complex sounds, the splices again become audible.

I've got a vox white shadow too though its a crimson/red colour with 2 chrome plated humbuckers, it has one volume pot, two tone pots, 1 toggle switch aswell as 2 further switches to change between pick-ups. It has stamped on the back neck plate "made in japan" I can't seem to locate the serial number though. Would love to know more about this guitar.
Some acoustic guitars, regardless of the body style, feature a cutaway in the upper bout to allow players to more easily reach the higher frets on the guitar neck. Phil Keaggy, a prolific and highly celebrated American guitarist, usually uses an acoustic guitar with a cutaway. If you plan to play leads on your acoustic, or are used to playing an electric guitar, you may prefer a guitar body with a cutaway.
While the Boss ME-80 doesn’t have anything in terms of extras to really blow expectations out of the water, it includes some nice and handy features. The onboard looper works well and has 38 seconds of loop time, which is enough time to do some basic jamming over some chords. And speaking of jamming, the AUX input on the back of the ME-80 is nice, since it allows you to plug in an iPhone/metronome/mp3 player/any other music playing device and jam along with your music (this is fun and a feature we would actually use). The USB output lets you take patch editing over to your computer, in BOSS's Tone Studio software. Cool, but not necessary since editing patches is actually very easy and actually quite fun on the unit itself (no complicated menus to go through - just fun knobs!). One idiosyncrasy to be aware of is that if you plug anything into the headphones jack, the speaker simulator is automatically enabled. This is great for solo practice in your headphones, but note that that’s the only way to actually switch it on.
Small guitars were often looked at as mere travel or couch alternatives, but times have changed and they are making a comeback on big stages. The LX1E Little Martin is at the forefront of this rekindled interest, with artists like Ed Sheeran impressing big crowds with just his humble and small LX1E. Thankfully, its price has remained stable despite the its current worldwide recognition.
Mahogany is a very dense, strong wood used in all parts of guitar manufacture except fretboards and bridges, which require harder wood. A mahogany neck and back are often found on short-scale guitars with maple tops. Another common combination is an all-mahogany body and neck (excluding the fretboard). Because mahogany is not very hard, it emphasizes the midrange and bass frequencies for a mellower guitar tone. Mahogany is a very resonant wood which enhances a guitar's sustain. It is generally a uniform rich brown color.

Ok, funny enough last week i got my old squire Tele out the loft to perform a maintenance on it and i adjusted the Truss rod, action, innotation. I've installed some nee pick ups too. But it still doesn't mean that there aren't easier guitars out there to play. There are differen't necks, frets, body shapes etc that all factor in. Someone has already said that a Tele is one of the hardest to play so i still think my question is valid

Guitar wiring refers to the electrical components, and interconnections thereof, inside an electric guitar (and, by extension, other electric instruments like the bass guitar or mandolin). It most commonly consists of pickups, potentiometers to adjust volume and tone, a switch to select between different pickups (if the instrument has more than one), and the output socket. There may be additional controls for specific functions; the most common of these are described below.
The Strat didn’t just sound different, its aesthetics and ergonomics were totally unique and innovative for its time. Instead of a standard slab body, the Stratocaster had double cutaways and was contoured in a way that had never been seen on a solid-body guitar. Originally built for legendary western-swing musician Bill Carson, it was quickly adopted by rock ’n’ roll pioneers like Buddy Holly and Hank Marvin, and has been the tone behind countless Top 40 hits.
When the tone pot is set to its maximum resistance (e.g. 250kΩ), all of the frequencies (low and high) have a relatively high path of resistance to ground. As we reduce the resistance of the tone pot to 0Ω, the impedance of the capacitor has more of an impact and we gradually lose more high frequencies to ground through the tone circuit. If we use a higher value capacitor, we lose more high frequencies and get a darker, fatter sound than if we use a lower value.
We’ve talked about four electric guitars by now. Let us talk about the “Mini” Strat from Squier by Fender. It is a “mini” guitar because it is has a small Strat and therefore, it is literally the best choice electric guitar if you want to buy one for your child. But that does not mean adults cannot use it. If you are a beginner who just wants to practice then this is a great model for practicing your skills.
PONTE NON TREMOLO Per cambiare le corde, infilare le corde nuove negli occhielli di guida sul retro della chitarra e posizionarle in seguito sopra la selletta. È possibile regolare l'intonazione spostando la selletta in avanti o indietro utilizzando un cacciavite a testa Phillips (+) sulla vite di regolazione dell'intonazione nella parte posteriore del ponte.

A very useful way of creating space for guitars in the final mix is to use tunable high-pass and low-pass filters to remove extreme frequencies that do nothing to enhance the guitar tone, but invade the space of other instruments that do perform in those areas. Generally speaking, it’s worth losing everything below 80Hz, although it’s not unusual to set the filter a good degree higher. Shaving off some high end may also be useful to help place the guitar in a specific area of the audio spectrum. Filter at the mixing stage, as the sound of the recording will often determine the optimum filtering points.
{"eVar4":"vintage: guitars","pageName":"[gc] vintage: guitars: silvertone","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop18":"skucondition|0||creationdate|1","prop2":"[gc] vintage: guitars","prop1":"[gc] vintage: guitars","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"classical & nylon guitars","prop5":"[gc] vintage: guitars","prop6":"[gc] vintage: guitars","prop3":"[gc] vintage: guitars","prop4":"[gc] vintage: guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] vintage"}
Matt Heafy, of Trivium is working on a signature 6 string and 7 string Les Paul with Epiphone. Heafy has said that ‘(I) chose Epiphone, because I have to work my way up, from an Epiphone, Gibson USA, then a Gibson Custom. The thing is if it was a Gibson Custom, the kids would be paying $6000 for it, and they can’t afford that. I want it to be affordable but something I will use on stage”[citation needed]
Aside from what brands to choose from and finding out the right budget to spend on an amp. Initial search for a guitar amplifier generally leads beginner players on figuring out that there are actually different types of guitar amps in the market. This is where they start to care deeply enough to know which amp sounds better and what will fit their playing the best.
Yamaha is the most revered and leading manufacturer of full-line musical instruments. With its wide range of guitars, the company has become a best seller and is easily one of the best guitar brands in India. The C Series are the popular and affordable nylon string guitars by Yamaha suitable for beginners and young learners. The electric guitars of Yamaha available in India are of the Pacifica and RGX series. The Pacifica series offers the most value for money combining affordability with performance.
{ "thumbImageID": "Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000", "defaultDisplayName": "Fender Special Edition Deluxe PJ Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Olympic White", "sku": "sku:site51500000048792", "price": "899.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-Olympic-White-1500000048792.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-Olympic-White/H96715000004000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-Olympic-White/H96715000004000-00-60x60.jpg", "imgAlt": "" } , { "name": "3-Tone Sunburst Maple", "sku": "sku:site51434378852529", "price": "899.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple-1434378852529.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple/H96715000003006", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-3-Tone-Sunburst-Maple/H96715000003006-00-60x60.jpg", "imgAlt": "" } , { "name": "Sea Foam Pearl", "sku": "sku:site51365435327256", "price": "699.99", "regularPrice": "899.99", "msrpPrice": "900.01", "priceVisibility": "1", "skuUrl": "/Fender/Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl-1365435327256.gc", "skuImageId": "Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000", "brandName": "Fender", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Special-Edition-Deluxe-PJ-Bass-Sea-Foam-Pearl/H96715000001000-00-60x60.jpg", "imgAlt": "" } ] }
This Yamaha Pacifica features a Strat sound that is very good, especially since the humbucker can be tuned into a single pickup by lifting up on the tone control. Like with every other strat, it has a five-way switch which allows the player to select the bridge pickup, the bridge+middle pickups, the middle pickup, the middle+neck pickups, or just the neck alone. In the event that you are tired of the strat sound and you would like to return to Led Zeppelin, simply flip to the humbucker and get set to go!
Chorus pedals actually make your guitar sound like there are a variety of different guitarists playing the same thing that you are playing, but with a different guitar and slightly out of time with you. This effect makes everything you play sound a little bit ‘warbly’ and thickens up your guitar or bass lines. We recommend experimenting with these as you can use them subtly to add weight to your sound or as a full-blown effect that completely takes over your signal.

Interestingly, the 2019 version of this guitar doesn't stray too far from the more expensive Standard model in terms of looks - some even prefer it over more expensive models because of its streamlined appearance. While there are no high grade tonewoods involved, the Les Paul Tribute still uses the same mahogany body and maple top combination. The 24.75" scale length neck also follows after the Standard model, complete with a 22-fret rosewood fretboard and a 1.695" nut width. As the name suggests, this model features a slim taper neck profile that modern players will appreciate. Finally, it is equipped with a 490R humbucker for the neck and a 490T humbucker for the bridge, which reproduces the sound of old Les Pauls from the '60s.
If you’re looking for a decent guitar at a super affordable price, look no further. This Ibanez features Powersound Pickups as well as 5-way switching to give you a variety of tones and styles. With a contoured body, it’s super easy to get comfortable while shredding away on this puppy. If your music styles fall in line with hard rock or country, then this is the guitar for you!

In 2007, Gibson announced the idea to create a computerized Les Paul, dubbed the “Robot Guitar” which was released on December 7, 2007. The guitar has a computer integrated into the body with a “master control” knob next to the volume knobs, which can be pulled out, turned, or pressed to issue different commands to the guitar. One of the more notable features is the ability to tune the guitar to standard tuning simply by pulling out on the master control knob and strumming the guitar, while the tuning pegs adjust themselves to standard tuning. Another use of the master control knob is to be able to tune the guitar to alternative tunings, such as drop D, by pressing on the control knob to fit the setting. The new Les Paul has a new custom silverburst blue finish.[30] While the product was advertised in the American popular press as a “world’s first”, similar systems, some external, have been in use for decades.
View tab notation as a representation of the guitar's strings. A tab is usually written using six horizontal lines, each corresponding with a string on the guitar. The bottom line represents the lowest, thickest string, while the top string represents the highest, thinnest string. For standard tunings, this means that the lines will represent, from the bottom up, the low E, A, D, G, B and high E strings.
: : I have a Vox Shadow that's sunburst, white pick guard that surrounds 3 solid chrome face pickups and the middle pick up has "VOX" engraved in it. 3 seperate volume controls and a master volume control. Tuning keys are all chrome, and the green decal on the face of the headstock reads Shadow, JMI Dartford, Kent. Neck is attached withthe help of a chrome plate, on the back side of the 'plank' body is an access plate for the jack that states made in England. Guitar also has the original roller/tremelo tail piece with palm lever. The numbers of 64728 are stamped on the back side of the headstock just below the tuning keys. Finish is beginning to crack a bit but it's all original, right down to the volume pots that have to be cleaned from time to time. It must be a rather unknown line that Vox had as I can't find out much on it either. Had this guitar for many years. Was handed to me in pieces in an old 'cardboard' case, (that has since gone away) put it back together and added it to my "music room".
I have tried many different wiring schemes as well, with 3-way switching, 3-way with coil taps, and even bypassed the tone control (since I never dial back the tone in my playing anyway). I have played this guitar through high-gain amps (Carvin V3, all three channels, Carvin Vai Legacy), through VOX AC15, Vox AC30 (both with Greenbacks and with Celestion Blues speakers), and an Orange 2x12 combo. In all of these excellent amps where my Carvin SC90 guitar sings and sparkles and does whatever I want it to, this Frankenstrat with Duncans or with Carvin P'ups sounds like a fart after 12 glasses of cheap Charles Shaw wine.
We gave our electro-acoustic chart a big refresh to keep it relevant for early 2018, by replacing a few older guitars with some excellent upgraded models. Guitars such as the Epiphone PR-4E and Mitchell MX400 were removed, and in came the exquisite Yamaha A Series A3M, the new PRS SE A50E, the cool Fender Sonoran SCE, and two solid budget models, the Kona K2 and Yamaha’s APX500III.
If you are recording the output of a bass amp, try to use a mic that will capture more of the low-end than a typical stage mic. An SM57/58 will work, but a mic with a more extended low-frequency response would be a better choice. The Sennheiser 421 is often used, as is the classic kick drum mic, the AKG D112, which has a bumped-up response tuned specifically for low-pitched instruments. I prefer the Electro-Voice RE-20 (you know, the “announcer’s mic”)—it’s more neutral, and it has an extended low-end response, so you’ll get not just boom, but real depth.
The Magnums met with a reception roughly as enthusiastic as the previous Breadwinner and Deacon. In the Carter tables it suggests that the Magnum line was redesigned to look like more conventional Fender-style basses with offset double cutaways in 1978. Other than the body shape, the 1263 Magnum III was identical to the I, and the 1264 Magnum IV was the same as the II.
If you have a little bit more to spend than what you pay for the Epiphone LP Special II you might want to consider the Epiphone Les Paul 100. It has a mahogany body with a maple top, mahogany neck and rosewood fingerboard. It’s got solid tuners and hardware, a 3-way switch and two tone and volume knobs. It’s slimmer and therefore much lighter than the Gibson Les Paul. The Epiphone LP 100 feels and plays good. It’s a reliable and durable guitar. A great choice for rock and blues!
Hi Timothy, sorry it took a while for me to respond. Yes, from your first statement it sounds like you’ve correctly understood the operation of ‘normal’ guitar pickup selector switches (i.e. standard 3 and 5 position), the wiper contacts overlap as they move across each other. Unfortunately I’ve never seen anything that matches your 4 pick-up idea, if I were you I’d start looking at the 5-position mega switches which have lots of possibilities but can get pretty complicated. Good luck!
Blueridge makes some excellent acoustic guitars, many of them based on historic designs. So, what does that mean? Many players feel that acoustics made in the early days after the dreadnought design had been created used better construction methods, qualities and materials compared to guitars produced today. In their historic designs, Blueridge attempts to capture some of that magic.

Our production/assemble time frame: 15 - 25 working days since our professional Control Team and Supervisor Engineer will ensure that your ordered guitar is top notch considering the fact that this guitar is intricate to assemble and they check very carefully every detail such as the finish, fret work, pickups, strings. And also, they will test the sound quality. We do not rush up the process of manufacturing your guitar since we would like to deliver to you best quality performance.
They may not always be the first thing you reach for, but the MIDI effects plug-ins that come with most DAW applications like Logic and Cubase often offer something very different from most audio plug-ins. For example, arpeggiators and step sequencers can be great for use in the composition process, and you can use MIDI note to controller data (CC) plug-ins to generate automation data for the parameters of other plug-ins. As they process only MIDI data, and not audio, MIDI plug-ins put very little strain on your computer. Matt Houghton
The smallest Taylor guitar available. The Baby Taylor series has been hailed for its easy-to-transport size and affordability. Features include sapele laminate back and sides with an optional Sitka spruce (identified as a BT1) or mahogany top (identified as a BT2). A larger bodied option is also available called the “Big Baby” (BBT introduced in 2002), which is a 15/16-size dreadnought with a neck that is standard scale (25-1/2”) and narrow width (1-11/16”). The Big Baby however only comes with a Sitka spruce top.
Essentially the 28s looked very similar to the E/EM/EB-18s. They had the same offset double cutaway body outline and the modified Viennese three-and-three headstock. Instead of maple laminate bodies with glued-in necks, the 28s had mahogany bodies and necks in a neck-through-body design. The basically slab bodies of the E-18 had gained a carved top, with a deep contour in the upper waist. The brass nut had become a Micarta nut. Fingerboards were now ebony. Finishes were sunburst.
By 1966 Daniel sold Danelectro to MCA, but remained with the company. In 1967 the Coral line of guitars is introduced. At the time, Danelectro sold about 85% of it's products to Sears. So MCA started the Coral line to sell to other distributors. The difference was the Coral hollow bodies (only) were manufactured in Japan. All other Coral parts were made in the New Jersey Danelectro plant. Also all Silvertones and Danelectro instruments were made entirely in the U.S.

{"eVar4":"shop: amplifiers and effects","eVar5":"shop: amplifiers and effects: amplifiers","reportSuiteIds":"guitarcenterprod","pageName":"[gc] shop: amplifiers and effects: amplifiers: guitar amplifiers","eVar3":"shop","prop2":"[gc] shop: amplifiers and effects: amplifiers","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop1":"[gc] shop: amplifiers and effects","events":"event1,event31","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"guitar amplifiers","prop5":"[gc] shop: amplifiers and effects: amplifiers: guitar amplifiers","prop6":"[gc] shop: amplifiers and effects: amplifiers: guitar amplifiers","prop3":"[gc] shop: amplifiers and effects: amplifiers: guitar amplifiers","prop4":"[gc] shop: amplifiers and effects: amplifiers: guitar amplifiers","eVar1":"guitar amp","prop9":"redirect","campaign":"4soswxxa","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category2","prop8":"guitar amp"}
1950s: occasional Adirondack red spruce. In 1952 or 1953, rumor has it Martin bought a large supply of Engelmann spruce from government surplus. Though Martin preferred Adirondack Red Spruce, it was no longer available after the mid-1940s because all of the large trees had been decimated. Martin would have liked to switch from Sitka to Engelmann because he felt that Engelmann was closer to Adi Red Spruce than Sitka was. He could not however find anyone who was cutting Engelmann commercially, so they went back to Sitka.
You may love only one style of music. And that’s fine. But try playing some other styles. Funk maestro Carlos Alomar went through hell on David Bowie’s Scary Monsters (and Super Creeps) album, being asked to play more “grinding” guitar alongside Robert Fripp. “It was very interesting,” says Alomar. “I learned a lot and when I came back to my more natural style, I felt really fresh about it.”
Their first flat-top acoustic guitar was produced some time shortly before 1910, but at that time their flat-tops were still a long way behind Martin in terms of popularity. It wasn't until 1923 that they began to seriously break into the flat-top acoustic guitar market with their signature Nick Lucas Special model and began to give Martin a run for their money.
Due to the acoustic, aesthetic and processing properties (workability, finishing, joints) the wood and the ligno-cellulose composites are the most valued materials for the musical instruments' construction. The guitar is made up of a complex structure, formed by a vertical wall in a curve shape (technologically named "sides") and two faces made up of ligno-cellulose plates, so that it should... [Show full abstract]
The best way to use this type of book is to just take 15 minutes a day to work through a page or two at a time. You don’t have to find something that requires a lot of study or dedication on your part at this point. Your first priority should be finding a book that gets you thinking about theory as well as helping you develop coordination in both your fretting and strumming hand.
Categories: Gibson Guitar CorporationBanjo manufacturing companiesBass guitar manufacturing companiesGuitar amplifier manufacturersAmerican companies established in 1902Manufacturing companies established in 19021902 establishments in MichiganCompanies based in Kalamazoo, MichiganManufacturing companies based in Michigan1902 in musicCompanies that filed for Chapter 11 bankruptcy in 2018
Since you're a beginner, lighter strings are probably going to be easier for you to play until you get your fretting hand built up with permanent callouses and finger strength. I would advise buying 9-42 gauge strings even if that's not what your guitar came with originally - if it had 10's on it from the factory, the 9's will feel slinkier and more forgiving on your hands.
I love them both, have a Strat and Les Paul. they are such different animals. Each has it’s place in my music, each has a special sound. Used to own a Tele which I just didn’t enjoy playing so much, so traded in for the Les Paul. I later bought a modified Tele with humbuckers (I know it’s a sin) but damn it sounds so good, for heavy power chords, more like a PRS sound. I’ve been playing 27 years now and am a composer / songwriter. Played in lots of bands, and during my live work I have to say I prefer my Strat. It’s lighter than the Gibson, and contours nicely to my body. With a good valve amp and the right strings I can get some lovely fat sounds out of it. I use the Gibson mostly in the studio. When I moved countries, I needed a cheap electric to tide me over until my stuff got sent over. I picked up a $100 Mitchel (Made in China). The setup was awful, totally unplayable, so set it up properly, and to be honest it plays like a dream. The neck is amazing for a $100 guitar, and with some new pickups the sound is great too. The upshot here is that it doesn’t really matter what guitar you use to make music on, as long as you enjoy the instrument, a cheap guitar can go a long way. I find the discussions about which is better kind of like guys comparing their crown jewels, it’s purely academic and what matters is how you use the thing 😉
He revolutionized music by combining two different guitar styles who were begging to be played together, blues and country. It was through this courage and confidence that Berry was able to convey his slick attitude that made everyone stop and listen. Sadly, however, even though his lyrics and performances were positively received, the artist himself did not have as positive a reception. He was said to be quite hard to get along with… but that didn’t stop his band swinging along. A sign of complete trust in what they were achieving together.
"Like any music technology, it's just a tool to help someone express their creativity. The gear never makes the player, but there's a purpose to it in certain playing situations and that's all good. As long as some guys are not hiding the truth of their playing behind it. A good player's a good player, and they usually sound good on an acoustic guitar simply because because they can actually play the damn thing.

Above here's a blast from the past. The reissue of the 1960's Harmony Stratotone H49 Jupiter. Originally this guitar was manufactured in Japan, but these babies came straight from China many years later. They copied them right down to the T including those Gold Foil Pups. Guitar is hollow body and has a volume, volume, tone, tone, master tone knob, with a really cool 3 way switch. They don't come up on Ebay to often and this ones like brand new but was briefly used. Sold

{"pageName":"[gc] pdp: gandl legacy solid body electric guitar","reportSuiteIds":"guitarcenterprod","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","events":"event34,event3,prodView","evar51":"default: united states","list1":"12-month,24-month,36-month","prop5":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop6":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop3":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop4":"[gc] shop: guitars: electric guitars: solid body electric guitars","products":";114488369;;;;evar65=Used-Guitars-G&L","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] product detail page"}
In the early 1960s the Brothers Grim became the first American group use Vox Amplifiers. Joe Benaron, CEO of Warwick Electronics Inc. / Thomas Organ Company, the United States distributor of Vox, along with Bernard Stockly (London), importer of Challenge pianos to the United States, arranged for the boys to have full use of the tall Super AC 100 Vox amps (4×12" speakers). The solid-state version of this amp (known in the USA as the "Super Beatle") was produced to cash in on the Beatles-Vox affiliation, but was not nearly as successful as the valve AC30 and AC15 models.
The Epiphone Joe Pass Emperor II is the signature guitar of one of jazz music’s great guitarists. Joe Pass played on records with Ella Fitzgerald, and his influence has cemented his name among the greats of the genre. The guitar which bears his name is a fine example of a guitar geared precisely towards one genre. It won’t win any awards for versatility, but it is a fantastic instrument for jazz fans of any skill level. Featuring the classic hollow body arch top design of old but with two high quality Burstbucker pickups for a range of silky tones.
Small amps can benefit from being placed on a stand, rather than the floor, as reflections from the floor can muddy the sound. A stool or something similar will do if a stand isn’t available. For the same reason, when using larger stacks or combos with several speakers, try mic’ing one that’s furthest from the floor. Placing an amp against a wall will increase the bottom-end response, and placing it in a corner will emphasise the low end further still. A mellow tone can be achieved by pointing the amp into the corner and mic’ing from behind.
The “New Improved” mid-’37 Supro line is illustrated in the 1938 Sorkin catalog from New York, as well as in the 1939 Grossman Music Company catalog from Cleveland (pecking order and all that). While the illustrations are heavily retouched versions of the older artwork, certain changes are evident, including a change in pickups. The Supro line continued to include the Spanish guitar and the late-’36 Hawaiian, plus a newly-designed amplifier.
All of these soundfonts can be opened with most zip programs, but if you are not sure or you haven't got a zip program you can use 7zip in windows or xarchiver in linux. I chose the SF.tar.bz2 format as it compressed to almost half the size of the original. Let me know if you have any problems downloading or extracting the files. These samples have been tested in SFZ free player in windows (check this forum for download details) and Qsynth in linux.
What style of music do you play? While there are many versatile guitar amps that can be used for many styles of music, if you play a particular style of music a majority of the time, then you should get an amplifier that best suits it. Do you play acoustic or electric? Certain guitar amplifiers are designed specifically for acoustic guitars although it is possible to play an acoustic through any amp. In terms of styles, jazz players typically do not need an overdrive option as clean tones are best suited for that style of music. Blues aficionados will be happiest with a clean channel plus an overdrive channel with plenty of sustain, such as one finds on many vintage Fender models. Shredders will require an amp that will accept distortion pedals without losing signal quality. Do your research regarding which guitar amps are best suited for the type of music you play.
I haven't had the pleasure of owning an Andrew White yet, but I plan to. I've followed the company and Andrew for some time after noticing repeated YouTube videos featuring unique guitars with lush, exotic tones. Since then, every time I've had a question or comment it is Andrew himself that responds quickly with pleasant and enthusiastic answers. Andrew White guitars have something different to offer and Andrew himself seems to be a down to earth guy with the passion of guitar building in his heart.
I'm going to break this review into pros and cons. Pros: Top notch wood, electronics, wonderful bound neck and great machine heads. The action/fretboard are wonderful (after being setup). Sounds beautiful!, and more so if you take my advice. One last pro, all of the cons are easily remedied. Cons: The saddle, nut, and bridge pins are plastic (kind of like putting crap tires on a good sports car). I replaced the saddle and nut with tusk, and for the bridge pins I went with brass. It was like the volume went from a 4 to a 8, and the tone went from nice to beautiful and singing. It was about a 40$ upgrade, that made it sound like a thousand dollar guitar. This is the first time I bought a guitar before playing it. The gamble more than paid off. Been playing guitar for 25 years, and I

The Seismic Audio SADIYG-15 JEM Style Electric Guitar Kit gives you the ultimate shredder guitar. Originally designed by Steve Vai, this style is built for speed. Innovative features like a Monkey Grip Handle and Floyd Rose Tremolo complete the unique design. All the parts needed for a finished guitar are included. This guitar kit is suitable for the aspiring or established luthier and all guitar players. A truss rod adjustment hex wrench, two Floyd Rose tremolo adjustment hex wrenches and solder are included. You will need a phillips head screwdriver and a soldering iron to fully assemble the guitar. A pack of six nickel alloy strings and a right-angle guitar cable are also included.With your purchase, you will receive one DIY JEM Style Electric Guitar Kit pictured and described above.
Sure, Marshall and Vox contributed to the sound of British rock in the Sixties and Seventies—but let us not forget the mighty Hiwatt DR103. Although it's often associated with the Who's Pete Townshend (who would test their durability night after night), it was a favorite of Pink Floyd's David Gilmour, not to mention the Moody Blues, the Stones and beyond. Although the DR103 looks a bit like a Marshall, it certainly doesn't sound like one. This was the result of a vastly different design.
Over the years in my travels, I've seen more Peavey amps on real working musicians' stages than any other amp manufacturer. The fact that real, everyday working musicians use and depend on them also dictates that Peavey amps are out there making more money for real working musicians in total, than any other amp out there. Yes, I know, the big act shows have huge backlines of Marshalls behind them, but they are in the minority, as there are more lesser-famed bands and musicians out there working than there are "stars". I "stepped down" to Peavey almost 20 years ago, when I was beginning to have reliability issues with my Fender amps...issues I couldn't afford to keep having while on the road. I still have my old Fender amps, but I've been gigging regularly and exclusively with only Peavey for the past almost 20 years now. I still get the tone I want and need and the reliability I expect in order to keep making a living in music. And by the way, I've been gigging since 1963.
i just started using this book never having played before and am finding it totally easy to follow. the friendly narrative guides the reader through every step, explaining the most simple of terms and concepts clearly and concisely. and yes, the CD is funky and you can play along with it more or less straight away AND sound good, which keeps you motivated.

My brother owns a Norma acoustic guitar modeled on the Gibson Hummingbird. He bought it used in the mid 70s. Solidly built but only average sound. I would guess that like many Japanese made guitars from the 70s, Norma was not a "company," but simply an American sounding brand name chosen by a larger Japanese instrument manufacturer to market their guitars in the USA. I own a mid 70s Penco acoustic, same deal, name was used on Japanese made guitars marketed through the Pennsylvania Music Company, thus Penco.
Following a raft of recent updates, the MS-50G now boasts over 100 effects and 22 amp models, six of which can be used simultaneously in any order. Add a chromatic tuner into the equation, and you're looking at a pedal for all seasons. The very playable amp models cover the popular options: there are three Fenders ('65 Twin Reverb, '65 Deluxe Reverb, Tweed Bassman), a Vox AC30 and a Marshall Plexi. You also get a Two-Rock Emerald 50, while a Diezel Herbert and Engl Invader cover the high-gain side of things. Effects include modulation, filter, pitch shift, distortion, delay and reverb. Most are generic, but some, particularly in the overdrive/distortion category, are modelled on well-known devices - the Big Muff and TS-808, for example. Each patch can be constructed from a chain of six effects blocks, each with a modelled amp or effect, DSP permitting. It all adds up to the most practical, cost-effective way to expand your pedalboard by adding a single pedal.
Compressor sometimes sounds good after distortion too, it helps with noise (compressors can be noisy and if put before overdrive then the distortion pedal makes the noise louder). Placing the compressor after distortion also increases your sustain (depending on the type and amount of distortion used!). It can sound darker if placed after as well - so it really is down to your ears and what you think sounds best! But I have mine first in the chain, before Fuzz as I don't often (ever?) use them together

Used Instrument Buyer - [New Window] - When it's time to sell your used instruments, nobody makes it easier than UIB. We make our best offer up front, right out of the gate, so you know you're getting top-dollar for your used musical equipment. Since 2006, we've helped everyone from professional musicians to weekend guitar warriors get the most value out of their used instruments. We offer free no-obligation quotes for your used equipment. upon your approval, simply pack your equipment, ship it to us free, and we'll promptly mail you a payment.
No matter how good a tech may be, his preferences are going to be different than yours on string height, etc. And he is never going to use the exact same amount of pressure fretting a note as you do (affects intonation adjustments). So, the best you can hope for is finding a good tech with good comunication skills, willing to listen to what you want. I'll admit I've never tried to find one, but that sounds more difficult than learning to do the setups yourself, which is what I did.
: Nor were Decca guitars made for or marketed to children. They were made at the same factory that made Teisco, Teisco del Rey, Kingston, Heit, Kawai and other brands of guitars. Some of these are quite decent beginner's instruments, and some are just flat out interesting/weird. No, they're not the same quality of a Gibson, Fender or Burns guitar from the same period, but they also cost a fraction of one of those guitars. And coincidentally, Fender guitars nowadays are largely made in Indonesia, China and Korea, places that *wish* they could make things as well as they can in Japan, so chew on that before you slag on Japanese-made guitars.
One of my favourite hardware effect units is the Electrix Mo-FX (sadly no longer in production). It is superbly constructed for hands-on performance and it offers full MIDI control over the panel's knobs and buttons. I use this in conjunction with the Sequentix P3 (a hardware step sequencer). Not only can the P3 generate patterns of controllers suitable for varying multiple Mo-FX parameters, but it can generate evolving or shifting patterns, courtesy of its 'accumulators'. In a nutshell, accumulators are designed to prevent your sequences becoming annoyingly repetitive: controller values (actually values directed at any internal sequencer parameter) can be added or subtracted on each pass of the pattern, with rules and limits directing the behaviour as the accumulation progresses. Digging through the Mo-FX manual quickly reveals all the MIDI Continuous Controllers you need. Usefully, you can also trigger the tap-tempo function via MIDI, and this offers a rather wonderful way of generating clock intervals. As you can decide exactly where to place your tap-tempo trigger events, and the P3 sequencer can shift or vary these events according to rules you devise, you can find clock sync intervals unseen on any other device. Paul Nagle
The electric bass was invented in the 1930s, but the instrument did not sell well until Leo Fender developed the Precision Bass in the 1950s. As such, the type of bass players who first began trying methods to make their instruments louder with amplifiers and speakers were upright bass players. While the upright bass is a large instrument, standing about six feet tall (with its endpin extended), due to its low register, it is not a loud instrument when played acoustically. This is largely a result of the decreased sensitivity of human hearing, which is most sensitive to mid-range tones; equal perceived loudness for a mid-range sound and a low frequency sound requires much more acoustic power in the low-frequency sound. In the 1890s and early 1900s, upright bass players performing in bars and brothels in an era before amplifiers and speakers were available, particularly those who performed in bands with louder instruments such as trumpet, often found it hard to be heard. About the only solution available in the pre-amplifiers era was playing slap bass, a style of slapping the strings against the fingerboard to make a relatively loud percussive sound. Beginning in the 1920s, the first amplifiers and speakers designed for gigging musicians became available.
A scaled down Grand Symphony travel size guitar. It features sapele laminate back and sides with an option of a solid mahogany or Sitka spruce top. It has been acclaimed for having a full size guitar sound despite being a compact size. Although it doesn’t come with an onboard Expression System, an optional ES-Go Pickup can be easily installed for amplification.
Martin guitars have been around for over 180 years, and are widely considered to be some of the best guitars currently in production. The Little Martin is a ¾ scale guitar perfect for kids and beginners with a smaller stature. Featuring professional-grade construction and hardware, the Little Martin has a big sound in a small package. Also great for travel, the compact body stows easily.

One of  the most widely used guitars in jazz, the ES-175 is a semi-acoustic, hollow-bodied archtop that comes equipped with two humbucking pickups. The ES-175’s deep body produces the thick, dark sound beloved of jazz guitarists and the thin neck allows for fast chording and soloing. The bridge pickup is capable of producing a less jazzy, thinner sound, and ES-175s can be used in blues and rock.
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Ash - Neck Attachment: Set - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Inlay: Pearl - Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black - Pickups: Ibanez - String Instrument Finish: Natural Blue
The Fender brand is the parent company of other good guitar brands like Jackson, Charvel, and Gretsch. While all of these are owned by Fender, they each have very unique playing styles and sounds. Fender also produces their Squire series of value guitars. These guitars are entry-level instruments, with decent sound for an incredibly reasonable price.
Blue Book Publications: Blue Book Publications publishes a number of print guides for musical instruments, and it also maintains a subscription-based website. The website is divided into electric guitars, acoustic guitars, and guitar amplifiers in addition to other instruments. Unlike Used Price, you will have to register for a paid membership with this site to get the information you need to self-appraise your guitar. You can access the prices online or purchase print editions to be mailed to you.

Another exotic tonewood is making a name for itself in the guitar industry. It’s similar in appearance and sound performance as Mahogany. It has a distinctive punch for the mid-range tones, but it emphasizes the bright trebles that can be an asset in music when you achieve pitch-perfect intonation. The Martin Road Series DRS1 Guitar sports Sapele beauty perfectly!

Japanese classical guitarist Shiro Arai founded the Arai Co. in the 1950s as an international importing company, which expanded to manufacturing in the 1960s adopting the "Aria" brand name. The explosion in popularity of the electric guitar in the 1960s led them to begin manufacturing and distributing several different brands, Lyle being one of them. Arai attended the NAMM trade show and saw many of the American guitar designs that had attained popularity in the U.S. This greatly influenced Arai to produce similar models.
While the number of effects may not be as many compared to recent releases, others don't have the same deep control and sound quality that the GT-100 provides. Speaking of control, instead of merely choosing your preferred amp, this processor lets you custom build your virtual amp and cabinet, an interesting feature that allows for even more freedom in crafting your own tones. Another feature that users are fond of is the ability to assign effects into its many footswitches, making the unit behave much like a regular pedalboard. Other notable features include polyphonic tuning and USB recording.
Pickups convert the mechanical energy of a vibrating string to an electrical signal, allowing it to be amplified, processed and reproduced.[1] Pickups vary greatly in construction, size, types of materials used, as well as various electrical properties, but are generally divided into two categories – single-coil and double-coil (also known as humbucker).[2]

Dexter Holland (b. 1965) is the rhythm guitarist of punk rock band The Offspring and has played Ibanez guitars for most of the band's existence. He currently uses a custom diamond plate RG with a custom Jägermeister logo on the twelfth fret, as well as DiMarzio Super Distortion pickups, though he used to use a brown and green custom RG and has been seen with a custom Purple RG.
The guitar is just a small step on being a guitar player. Having a budget friendly guitar to practice and learn with is suitable enough at this stage. The key to success really depends on how you practice and dedicate yourself on learning how to play. As long as you have a decent sounding playable guitar to begin with and has the quality that can last you in years to come. You’ll be all set.

Some more advanced models, like the Wampler Latitude Tremolo Deluxe, bring a much more complex set of features, which include choosing the waveform and more. Whether you are looking for a good way to spice up your tone without impacting the nature of your signal, or you are just in need of a great vintage style effect, tremolo is the one to go for.
However, if you want a small guitar that will give the quality of sound you might expect from a larger guitar, or if you are considering this style as the first beginner guitar for a child or student, you may want to consider other models that are more typical of a guitar suitable for learning, recording or for growing and developing better skills.

Three acoustic guitars were offered in 1971. These were glued-neck models with roughly Martin-shaped heads and pickguards slightly larger and squarer than a Martin. All had spruce tops (presumably plywood), mahogany bodies and necks, rosewood fingerboards and dot inlays. These appear to be Japanese, not Brazilian Gianninis. The bridges are glued on, with screw-adjustable saddles and pins. The U3012 Auditorium was a Spanish-shaped steel-string and cost $89.50 plus the cost of a case. The U3013 Grand Auditorium was a dreadnought costing $105. The U3014 Twelve String cost $120.
{"eVar4":"vintage: guitars","pageName":"[gc] vintage: guitars: alvarez","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop18":"skucondition|0||creationdate|1","prop2":"[gc] vintage: guitars","prop1":"[gc] vintage: guitars","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"guitars","prop5":"[gc] vintage: guitars","prop6":"[gc] vintage: guitars","prop3":"[gc] vintage: guitars","prop4":"[gc] vintage: guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] vintage"}
For guitarists who must have original-era Strat® sound, look and feel, the Classic Series '60s Stratocaster Lacquer epitomizes the instrument during its second decade, when musicians used it to conjure and create electrifying sounds never before imagined or experienced. With authentic features including a nitrocellulose lacquer finish in classic Fiesta Red, everything about it takes you back to a wildly creative time when rock music came into its own—from surf to psychedelia and more—and players started to discover in earnest just what a phenomenal instrument the Stratocaster really was.
The Hi-Flier guitar, which was possibly built in the Matsumoku factory, underwent multiple phases during the course of its production. Each of the Hi-Flier’s four manufacturing phases came with a variety of feature changes, ranging from simply switching the color of the pickguard to actually fitting the guitar for humbuckers rather than the P90-style pickups it originally came with.
When recording an electric guitar, the amp is the instrument as far as the mic is concerned, and mic position is important. While a lot of sound comes direct from the speakers as you'd expect, a significant level is also emitted from the back and sides of the box via panel vibrations. Also, an open-backed cabinet throws about as much sound out of the back of the box as it does out of the front. Choosing a mic for recording electric guitar isn't difficult, as virtually any decent mic of any type can be made to produce usable results. If I were to generalise, I'd say that British recording engineers tend to use cardioid, dynamic models while American engineers seem to prefer capacitor microphones. The dynamic mic produces a solid sound with a smooth high end, while the capacitor mic's increased definition produces a brighter, more open sound when used in the same way. However, the mic position has just as much bearing on the tone as the mic itself.
{ "thumbImageID": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-3-Color-Sunburst/L21533000005000", "defaultDisplayName": "Fender Player Stratocaster Maple Fingerboard Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "3-Color Sunburst", "sku": "sku:site51500000219387", "price": "649.99", "regularPrice": "649.99", "msrpPrice": "650.01", "priceVisibility": "1", "skuUrl": "/Fender/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-3-Color-Sunburst-1500000219387.gc", "skuImageId": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-3-Color-Sunburst/L21533000005000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-3-Color-Sunburst/L21533000005000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51500000219385", "price": "649.99", "regularPrice": "649.99", "msrpPrice": "650.01", "priceVisibility": "1", "skuUrl": "/Fender/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Black-1500000219385.gc", "skuImageId": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Black/L21533000001000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Black/L21533000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Polar White", "sku": "sku:site51500000219381", "price": "649.99", "regularPrice": "649.99", "msrpPrice": "650.01", "priceVisibility": "1", "skuUrl": "/Fender/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Polar-White-1500000219381.gc", "skuImageId": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Polar-White/L21533000003000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Polar-White/L21533000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Buttercream", "sku": "sku:site51500000219388", "price": "649.99", "regularPrice": "649.99", "msrpPrice": "650.01", "priceVisibility": "1", "skuUrl": "/Fender/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Buttercream-1500000219388.gc", "skuImageId": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Buttercream/L21533000004000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Buttercream/L21533000004000-00-60x60.jpg", "imgAlt": "" } , { "name": "Tidepool", "sku": "sku:site51500000219384", "price": "649.99", "regularPrice": "649.99", "msrpPrice": "650.01", "priceVisibility": "1", "skuUrl": "/Fender/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Tidepool-1500000219384.gc", "skuImageId": "Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Tidepool/L21533000002000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Player-Stratocaster-Maple-Fingerboard-Electric-Guitar-Tidepool/L21533000002000-00-60x60.jpg", "imgAlt": "" } ] }