The 1952 Les Paul featured two P-90 single coil pickups, and a one-piece, ‘trapeze’-style bridge and tailpiece, with strings that were fitted under (instead of over) a steel stop-bar.[note 3] The weight and the tonal characteristics of the Les Paul were largely due to the mahogany and maple construction: maple is a hard and quite heavy wood, but was restricted to a cap over somewhat lighter mahogany, to keep weight under control.[note 4] In addition, the early 1952 Les Pauls were never issued serial numbers, did not have bound bodies, and are considered by some as “LP Model prototypes”. However, the later 1952 Les Pauls were issued serial numbers and also came with bound bodies. Interestingly, the design scheme of some of these early models varied. For instance, some of the Les Pauls of this issue were fitted with black covered P90 pickups instead of the cream-colored plastic covers that are associated with this guitar, even today. Of note, these early models, nicknamed “Goldtops”, have begun to gain the interest of collectors, and subsequently, the associated nostalgic value of this instrument is increasing.[note 5]
The EM-18 came with either a pair of Mighty Mite humbuckers or a pair of DiMarzios. It was otherwise the same as the E-18 with the addition of a three-way mini-toggle coil selector switch which allowed a choice of both or either coil on the lead pickup. This arrangement allowed for a rather remarkable variety of tones, by the way. EM-18 production began in 1979 and some 1,375 were made until the guitar ended in February 1982.
Get superior guitar tone and flexibility using this 15-Watt, 1x12 Guitar Combo Tube Amplifier with Celestion Speaker & Spring Reverb from Monoprice! As the title indicates, this guitar amplifier features a 15-watt tube power amplifier and a Celestion brand speaker. It uses three ECC83/12AX7 preamplification tubes and two EL84 power tubes for the amplifier section, plus a Celestion Red Truvox 1215 speaker. The EL84 tube is the tube that powered the Mullard amplifiers favored by the British Invasion bands of the 1960s.
Chorus pedals can provide a nice subtle doubling effect to the guitar or an extreme “watery” effect when maximized. Famous tunes that use chorus is “Come As You Are” (1991) by Nirvana, and “Brass in Pocket” (1979) by The Pretenders. But basically almost any clean guitar sound in the 80’s had some chorus on it! Certain effects are timeless such as overdrive, reverb and delay. Other effects like chorus can evoke certain time periods such as the 80’s so that is something to keep in mind when using an effect.
On PremierGuitar.com, "Sponsored Content" refers to articles, videos, or audio recordings that are produced or curated by an advertiser but that Premier Guitar is happy to share alongside our own editorial content due to the Sponsored Content’s educational, musical, or entertainment value. Sponsored Content is clearly labeled everywhere it appears, and Premier Guitar's editorial department has no involvement in its creation.
To create a fairly live, in-your-face sound, a short reverb or ambience program with a fairly bright character is ideal. A hint of slapback echo or a little pre-delay before the first reflection can enhance the sense of power and intimacy, as when a guitar is played in a small club. More generous reverb can be combined with repeat echo effects to create a lush, spacious sound, but you need to leave space in the instrumentation and arrangements for these sounds to work, otherwise they just sound confused and messy. Feeding the effects send through a chorus or flanger before the reverb gives a nicely complex twist to the sound without being too obvious.
Ibanez are a Japanese guitar brand founded in Nagoya, Japan in 1957. They began by building copies of Fender and Gibson models, but – a couple of lawsuits later – they started creating their own models, which are now icons in their own right. Their line currently includes their famous Roadstar (RG), the thin-bodied S series, and several artist signature models, including guitars for Steve Vai, Joe Satriani, and Mick Thomson.
The Acoustic Resonance control gives you the option of adding life back in to your sound. Where some pickups, Piezos in particular can sometimes sound “quacky” and hard, due to the fact they only pick up the sound of the bridge area, the AD-10 analyses your pickup signal and recreates the missing body and string resonances accurately to ensure the subtle tonalities of your playing qualities of your guitar are intact.

{ "thumbImageID": "Stingray-Electric-Bass-Mint-Green/J38558000001000", "defaultDisplayName": "Ernie Ball Music Man Stingray Electric Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Mint Green", "sku": "sku:site51500000012369", "price": "1,799.00", "regularPrice": "1,799.00", "msrpPrice": "1,800.01", "priceVisibility": "1", "skuUrl": "/Ernie-Ball-Music-Man/Stingray-Electric-Bass-Mint-Green-1500000012369.gc", "skuImageId": "Stingray-Electric-Bass-Mint-Green/J38558000001000", "brandName": "Ernie Ball Music Man", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Stingray-Electric-Bass-Mint-Green/J38558000001000-00-60x60.jpg", "imgAlt": "" } ] }
Here for you is a beautiful Vintage 1964 Epiphone Frontier FT-110 acoustic guitar. This guitar is 100% original and comes along with it's original hard shell case. The guitar plays and sounds just great. These Epiphone guitars were made with a full 25 1/2" scale. The sound is just outstanding and the playability is fantastic. If you have any questions, feel free to either email us at or call .
It features a solid mahogany top with laminated sapele back and sides, leading to a warm tone that’s a joy to listen too. Despite the small body size, the BT2 has a robust projection, thanks to the arched back. The neck is joined to the body via screws, which tarnish the look a little, but leave no impact on the slick playability or the tone, so aren’t a big deal.
The tone knob is similar. Like the volume knob, the more you turn down the knob, the more of the sound you contain instead of sending it through the amplifier. But there is an additional trick involved. See, the current generated from each string is quite complex, like the sound characteristics it produces. Think of it like a continuum. On one end, the current is turned into low frequency sound (which makes the guitar sound 'warm') and on the other end of the continuum, the current generates high frequency sound (which makes the guitar sound 'bright').
    	AmpliTube's effects are as noteworthy as its amp modeling capabilities. The current version comes with up to 51 effects - modeled after rare vintage gear like Ibanez Tube Screamer, Arbiter FuzzFace, MXR Phase100, MXR Dynacomp, Electro Harmonix Memory Man and many more. What sets AmpliTube apart from the competition though is its very intuitive interface. No parameter is more than two clicks away, and its realistic looking graphics are extremely easy to operate - even allowing for drag and drop operations. If you want a quick setup software, AmpliTube is your best bet. Price: usually about $200 - Check out Amazon.com for the latest price and reviews

If you decide to use my link to Guitar Tricks when you sign up as a member, I will receive a compensation for my referral. I am not a professional reviewer and my views are biased because I only recommend stuff that I use and like. I appreciate if you follow my links to Guitar Tricks if you like I Really Like Guitars and my review of Guitar Tricks. Thank you!
This mod works great for Strat-type pickups or aftermarket Tele-style reproduction pickups that don’t already have a plate. Some pickup companies make P-90s that don’t have a metal base plate, and these can be twang-ified in this way, too. The best part is that, if you don’t like the sound, you can just peel the plate off and be right back where you started.

In the studio, a dynamic noise filter such as the Symetrix 511A, Drawmer DF320/330, Rocktron Hush or Dbx Silencer can be less obtrusive than a gate for cleaning up guitar parts to which delay/reverb has not yet been added. Very generally, such devices work by progressively reducing the audio bandwidth once the sound falls below an adjustable threshold. Transients pass through with very little change, while high frequencies are removed from the tail end of decaying sounds, which reduces the subjective hiss level. A conventional expander then mutes the signal entirely at very low levels.

A very good option in the budget pedal market. Comes with a great number of effects to combine for solid sounds. Virtually all the factory pre-sets are worthless and are sort of demonstrations of what the pedal can do. But you have plenty of user saves and setting up good tones is straight forward and simple. The tuner in this and my handheld one never agree. Someone is lying!
This guitar is of the finest, and yet it is only fraction of the cost that you would normally pay. You may be wondering how such an amazing product could be so cheap, it is possible because it has been manufactured in China, where labor is cheap. Cheap labor does not mean that has been compromised; all parts are of the highest. We have our own factory that recreates them. Our version of Custom Shop Guitars is 95% same as the original in terms of quality and design, the parts are made and imported from China, Japan and Korea in order to manufacture the best musical instruments. When purchasing this guitar you can only stand to win. If you are satisfied, you have just saved yourself hundreds of dollars! So go on, treat yourself to the guitar you have always wanted. We use the best pickups; best tuning keys and other hardware. All of our guitars are custom made guitars. The Top Guitars specializes the world’s finest custom guitars, major guitar brands, boutique brands and collectible guitars. Owning the latest state of the art equipment, craftsmanship and skilled technicians. Our products are exported to Southeast Asia, North America and Europe. Our 100% satisfaction guarantee allows you to buy with confidence!
Eddie Kramer has a slightly different approach, working from a familiar setup of favourite close and ambient mics (including the Beyerdynamic M160 ribbon mic) and then mixing them together to taste. "I use a three-mic technique: an SM57, an MD421 and an M160, all in a very tight pattern. Then I can pick and choose the tone quality, because each mic is totally different. I combine these together, and then I put a U67 away from the amp to get the ambience."
This is a wide range of electric guitar series that have a stylish body and deliver high-quality sound. Cort guitars are fabricated by South Korean manufactures and have been on the market since 1973. Those who are keen on the appearance of the guitar can opt for this brand of electric guitar. This is an electric guitar that is available at an affordable price range between 10,000 to 40,000 INR.
To start off our list (albeit rather difficult to choose a specific guitar first), let’s take a look at the Fender Telecaster, a high-quality electric guitar for the musician out there who is looking to improve their amateur status to accomplished guitarist. With the clear tone and quality range that the Fender brand is known to famously provide, the Telecaster is equipped with shielded body cavities meant to limit reverberation and focus in on the individual notes. The dual single-coil pickups allow the musician to vary between sharp tones and strong treble, providing a unique sound to fit various genres of interest. The flat surface of the of the fingerboard makes it easy to switch between notes and chords, while the alder wood used for the body of the guitar provides and even and bright sound. With a ‘C’ shaped design meant for comfort for long wear use, the Fender Telecaster is one of the best electric guitars for the money. The sound? Very classic, biting, and clear. You’ll have to hear for yourself in this Telecaster video, since we can’t really find adjectives to truly portray this beauty.
A modern popular rock artist known for use of the Super Beatle is Tom Petty and the Heartbreakers, although in the April 2008 issue of Premier Guitar, lead guitarist Mike Campbell revealed that the Super Beatle backline was, on their thirtieth anniversary tour at least, primarily used only as a stage prop, though Petty used his "on a couple of songs." In the group's early days, the Vox equipment was chosen because it was relatively inexpensive in 1976, yet had a handsome appearance. A photograph included in the article showed Campbell's guitar sound was coming from other amplifiers hidden behind the large Super Beatles, which Campbell stated were "a tweed Fender Deluxe and a blackface Fender Princeton together behind the Super Beatle, and an isolated Vox AC30 that I have backstage in a box."
10% of our readers voted for brands that were not listed in the survey. So, besides G&L, Jackson, Yamaha, Danelectro, Charvel, Cort, Washburn, Framus, Parker, Dean, B.C Rich, and Aria, you might also want to check Duesenberg, Wild Customs, Mayones, Caparison, Reverend, Blackat, Hagstrom, Peerless, Carvin, Guild, Cole Clark, Seagull, Meloduende, Suhr, Nik Huber, Feline, Ozark, Burns, Ruokangas, and Eko.
In 2003, The Blues, a PBS-TV series produced by famed director Martin Scorsese, traced the roots of the blues from Africa to modern day society, showing how it inspired other generations of musicians. While in production, Marshall Chess got an e-mail from Chuck D saying that he heard he was doing a film that connected the blues to hip hop and that he wanted to be part of it. Chess was happy to hear Chuck D say "Electric Mud was one of his favorite, most influential albums and that all the early hip hop guys were inspired by it," affirming a connection he thought had happened. In the episode titled Godfathers and Sons, the focus is on the Chicago blues, Chess records and the effect of Electric Mud on Public Enemy, with Chuck D coming to Chicago, led on a historic blues tour by Chess. There, Chuck D's feverant appreciation of EM got him to reassemble the musicians from the sessions to perform material from it for the upcoming 20th Anniversary Chicago Blues Festival. In keeping with the experimental vein of the record, Chuck D added a turntablist (Juice) and a rapper (Kyle Jason) to the band, re-naming the group the Electric Mudcats. Having the material played at a blues festival showed how the album had finally come full circle, from being hated to being respected and enjoyed.

The company has been run by the Martin family throughout its history. The current chairman and CEO, C.F. ‘Chris’ Martin IV, is the great-great-great-grandson of the founder. The firm was the first to introduce many of the characteristic features of the modern flattop, steel-strung acoustic guitar. Influential innovations include the Dreadnought body style and scalloped bracing. Some time in the 1970s, Martin bought Levin guitars[1] and around 200 D-18’s were apparently built in Sweden; they are stamped LD-18[citation needed].
The model designations of the archtops are unknown. Later these guitars would have either a PE or EP model designation, so presumably the ones in the photo did, too. One appears to be a full-sized, thick-bodied archtop with a rounded cutaway. Not much is visible in the photo, but it apparently had a single, white-covered pickup at the neck, block inlays and a white pickguard. The other guitar had a single pointed Florentine cutaway and was slightly smaller than, say, a Gibson ES-335. It’s impossible to tell the depth from the photo, but it looks as though it’s a thinline. This, too, had a single white pickup at the neck, moveable adjustable bridge, trapeze tail, large white pickguard (not modelled on a typical Gibson shape, by the way), a little plastic plate on the lower bout with volume and tone, with white knobs. The fingerboard has large white dots, with double small dots at the octave. The f-holes are three-part; the headstock Teisco three-and-three.
Thanks to the built-in pickup system, you can amplify your acoustic guitar by simply plugging it in, without having to perform any installation or tweaking beforehand. This bundle gives you a reliable 10-watt amplifier for electric performances, a digital clip-on tuner to keep your guitar in tune, a gig bag for safe transportation, a truss rod, extra picks and strings, and a strap.
Gibson has issued two Signature Les Paul guitars for Joe Perry of Aerosmith. The first was developed in the 1990s and was customized with an active mid-boost control, black chrome hardware, and a translucent black finish. It was replaced in 2004 by a second, more visually distinctive Les Paul, the Joe Perry Boneyard Les Paul. This guitar is characterized by Perry’s custom “Boneyard” logo on the headstock and a figured maple top with a green tiger finish, and is available with either a stopbar tailpiece or a Bigsby tailpiece; Perry typically uses a Bigsby-equipped Boneyard model in Aerosmith and solo live shows.

Clearly if you need a Gibson but have to count your pennies Epiphone should be your top choice. However, Some people don’t realize that Epiphone was once a competitor with Gibson, and even today some of their semi-hollow and hollow-body guitars are worth mentioning with the top brands out there. The Dot is well known as an affordable version of the Gibson ES-335, but there are also guitars like the Casino, Wildkat, Sheraton and Broadway.

If you already have an electric guitar and you're looking for replacement strings, carry cases, guitar stands, or other accessories, you've come to the right place. Amazon.com offers a selection of tools and accessories designed for players of every age and skill level, from beginners to pros. Look for amplifiers, cables, and microphones too—you can enjoy great selection right here online, with no need to make a special trip to the guitar shop.
In 2005, Gibson issued three Pete Townshend signature edition Les Paul Deluxe guitars, based on Townshend’s heavily customised “#1” Wine Red 1976 Les Paul Deluxe, “#3” Gold top 1976, and “#9” Cherry Sunburst 1976. These guitars were modified by Alan Rogan and used extensively on stage and in the studio with The Who. In addition to the two mini-humbuckers the guitar carried, Rogan modified Townshend’s originals with a DiMarzio humbucker in the middle. Toggle switches located behind the guitar’s tailpiece turned the pickup on and off and added volume boost. The control knobs were wired for volume, one for each pickup and a master volume. The reissues differed from Townshend’s originals in that the reissues had an inlay at the first fret while the originals did not.
The Omen-6 is a stripped down take on the Hellraiser, with the same sleek double cutaway design and HH (dual humbucker) configuration, but at a more affordable price point. But what's good about it is how Schecter is able to maintain the premium look and attention to detail at this lower price point, including the carved top design. While the name again implies something evil, this guitar is quite good for the price.
Gibson Les Paul Studio Electric Guitar The Gibson Les Paul Studio electric guitar has been around since 1983. For 2018 Gibson upgraded one of its most well-loved models, fitting it with cryogenically treated frets for greater fret durability, adding fingerboard binding and giving it a Slim Taper neck profile. The core Les Paul tones and quality hardware and electronics are still there, of course.

New York City native Joe Charupakorn is a guitarist, author, and editor. He has interviewed the world’s biggest guitar icons including Steve Vai, Joe Satriani, Yngwie Malmsteen, Carlos Santana, Neal Schon, and Dave Davies, among many others, for Premier Guitar. Additionally, he has written over 20 instructional books for Hal Leonard Corporation. His books are available worldwide and have been translated into many languages. Visit him on the web at joecharupakorn.com.
{"id": "L20582", "categoryId":"site5AAG", "name":"Slash Firebird Limited-Edition Electric Guitar", "pageUrl":"/Epiphone/Slash-Firebird-Limited-Edition-Electric-Guitar.gc", "thumbnailUrl":"https://media.guitarcenter.com/is/image/MMGS7/Slash-Firebird-Limited-Edition-Electric-Guitar-Trans-Black/L20582000001000-00-180x180.jpg", "hasFeatures":"0", "isAccessory":"0", "message":"", "value":"899.00", "priceMin":"899.00", "priceMax":"899.00", "msrp":"1,499.00", "productVisibilityMSRP":"1", "restockPrice":"", "openBoxPrice":"", "clearancePrice":"", "isPlatinum":"0", "priceSavingsMaxPrice":"0.00", "priceSavingsMaxPercent":"0", "inventory":"0", "brand":"Epiphone", "reviewStarImageUrl": "https://static.guitarcenter.com/img/brand/gc/cmn/Sprit-Sm-Stars.png", "reviewStarRating":"0.0", "reviewStarRatingInteger":"0", "reviewHowManyReviews":"0", "usedOrNew":"new", "discontinued":"0", "onOrder":"0", "clearance":"0", "canBeSold":"1", "accessoryCategories":"site5LFMIC,site5LAAA,site5HBA", "stickerText": "Top Seller", "isVintage": "0", "outletonly": "0", "checksum":"565047124900", "priceVisibility": "1", "itemType": "New"}

Finally the ease and portability of the small amp will allow you so much more flexibility with when and where you can practice. Just weighing a couple of pounds is already a great advantage over the rest of the amps available on the market. And being able to take it on road trips, travel trips, backpacking trips (for a bit of extra buck, we all have thought of doing it) means you can practice anywhere, any time. Small storage requirement means a great storing capability where you don’t have to worry about taking up too much space in your tiny room or apartment. It is great stuff, honestly.


The acoustic guitar is one of the most popular instruments around. It’s versatile, low maintenance and sounds great. You don’t need to lug around an amp if you’re just playing for a few friends and it provides enough volume to accompany vocals but not so much that it overshadows them. I personally love playing acoustic guitar. Everything from the sound to the feel of playing a nice acoustic is satisfying. What’s even more satisfying is learning how to play some great acoustic guitar songs. There are so many amazing acoustic guitar songs out there that it’s hard to narrow down
Believe it or not, some thought should be given as to where the compressor goes in your signal chain. A good rule of thumb is to place any gain-type effects before modulation effects: i.e., compressors and overdrives before delays or flangers. Another one that's practically set in concrete is to put the compressor before any overdrive, distortion, or fuzz pedal. This is why most guitarists place the compressor first, in order to send a stronger, better signal to the other effects.
If you want to get this game, you have a few options. The game is $60 with no guitar cable included; this is the best bet for owners of the original "Rocksmith," as the cable that came with that game works here, too. If you don't have the cable, but have a guitar, the game costs $80. If you need a guitar, too, that'll run you $200 for an Epiphone Les Paul Electric Jr. guitar, plus the game and cable.
The Reaction Many manufacturers reacted by making warranties void if amps were driven at full power, some threatened to cut off retailers who sold their amps to bands that played ‘music of the devil’. The parody of this historical contradiction has been rewritten, to fit mythical beliefs that brilliant designers created these amps for what ‘rock musos’ wanted.
Yes, he wears a KFC bucket on his head and a Michael Myers mask on his face, but he's a genius. Buckethead (real name Brian Carroll) plays every style, from country to death metal. Albums like 'Monsters and Robots' and 'Population Override' are must-haves for any aspiring guitarists, and instrumentals like 'Nottingham Lace' and 'Too Many Humans' take some beating. - Floods
If you've NEVER heard of EZMix for effects, Impact Soundworks Shreddage 2 IBZ or Prominy V-Metal for guitar, or Alchemist Studios Texas Grind for bass, or Impact Soundworks Shreddage Drums for drums, then I would say you're right, (Amplitube 4 is out right now, by the way). You need Kontakt 5.5 for all of this to work though, so if you have this already you need to upgrade.
{ "thumbImageID": "GRX70QA-Electric-Guitar-Transparent-Blue-Burst/H77128000001000", "defaultDisplayName": "Ibanez GRX70QA Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Transparent Blue Burst", "sku": "sku:site51313248770709", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Blue-Burst-1313248770709.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Blue-Burst/H77128000001000", "brandName": "Ibanez", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/GRX70QA-Electric-Guitar-Transparent-Blue-Burst/H77128000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Transparent Red Burst", "sku": "sku:site51313248770799", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Red-Burst-1313248770799.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Red-Burst/H77128000003000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/GRX70QA-Electric-Guitar-Transparent-Red-Burst/H77128000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Transparent Black Sunburst", "sku": "sku:site51313248770729", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "285.70", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX70QA-Electric-Guitar-Transparent-Black-Sunburst-1313248770729.gc", "skuImageId": "GRX70QA-Electric-Guitar-Transparent-Black-Sunburst/H77128000002000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/GRX70QA-Electric-Guitar-Transparent-Black-Sunburst/H77128000002000-00-60x60.jpg", "imgAlt": "" } ] }

A variation of the wah pedal is the auto wah. Not to be confused with a city in Canada, auto-wah effects do the same things a wah does, but without the foot treadle. Usually, you can adjust the attack time (how fast the tone shifts toward the treble) and the depth of the cycle. Some auto-wahs also let you set a constant up and down motion that's not triggered by the note. You’ll find auto-wahs included in many multi-effects processors. One of the newer developments in this area is the Talking Pedal from Electro-Harmonix. While eliminating the moving parts of traditional wahs, it produces amazing male-vocal and vowel-sound effects that harmonize with your guitar’s notes. A fuzz circuit lets you dial in more growl and grit.
when I started playing, if you wanted distortion, you "cranked up" the volume on the guitar and the amp. my old Gibson amp had reverb and tremolo. I used to play without reverb or tremolo. nowadays, in my old age, I use a little reverb for flavoring. I have pedals, but it's too much hassle to set everything up. so, I just plug into the amp with a little reverb. I'm happy and that's all that really counts. isn't it ?
Guitar amp modeling devices and software can reproduce various guitar-specific distortion qualities that are associated with a range of popular "stomp box" pedals and amplifiers. Amp modeling devices typically use digital signal processing to recreate the sound of plugging into analogue pedals and overdriven valve amplifiers. The most sophisticated devices allow the user to customize the simulated results of using different preamp, power-tube, speaker distortion, speaker cabinet, and microphone placement combinations. For example, a guitarist using a small amp modeling pedal could simulate the sound of plugging their electric guitar into a heavy vintage valve amplifier and a stack of 8 X 10" speaker cabinets.
Electric guitars are the easier to play as compared to acoustic guitars. But only because the chords are easy to play, that much force is not required to hold the chords as well as strum the chords. So it would better if you first practice the chords and the strumming on an acoustic guitar. The song Yellow by Coldplay, mentioned below, is considered as one of the best guitar tabs for beginners.
My question for this forum is this: I currently have a 2011 Fender Blacktop HH Stratocaster. It has the stock five position switch. All of the electronics are imports i.e.Korea, China etc.. I recently purchased a complete loaded pickguard from a Fender American Standard HH Strat. due to the poor overall performance of the Blacktop electronics-pickups included. Since the Amer. Stan. HH has only a 3 pos. switch, can I rewire it for a five pos. switch ( i.e. coil tapping the humbuckers as the Blacktop is configured)? If this is possible, where would I find a wiring diagram for these particular Fender Twin Head Vintage pickups showing them in use with a 5 pos. switch? Thank you for your time and cooperation.
Since 1977, Dean Guitars has been a leading guitar company manufacturing the highest quality electric guitars, acoustics, and bass guitars for musicians of all ages and at all price ranges. From guitar legends to beginners, we offer a choice for any music genre or style. Browse guitars and more all packed with a limited life-time warranty. Get Your Wings today!
(Book). Backbeat's successful Handbook format applied to the world's most popular instrument. The Electric Guitar Handbook is the latest entry in Backbeat's best-selling handbook series, combining a two-part book and an audio CD in a practical lay-flat binding for ease of reference when playing. Part one of the book examines how different types of electric guitars are made, and why varying construction methods influence the way guitars sound. It also looks at the role of various pieces of guitar hardware, including pick-ups, tremolo set-ups, and bridges. Part two is a comprehensive, user-friendly course in playing the electric guitar, from the basics of posture and hand positioning to music and tab reading and advanced performance. Newly written exercises presented in the book and also on the accompanying CD take the learner through each step in the process, covering styles including rock, country, blues, soul/funk, indie/alternative, and metal. Author Rod Fogg also offers practical advice on everything from simple scales to complex chords, alongside short features introducing key performers and styles.
While electric guitar manufacturers like this are often more expensive, they do provide a level of customization that isn’t available with several mainline models. Most companies of this size can have a casual email or phone conversation with you, take a few notes about how you want your guitar setup (probably jotting it all down with pen and paper) and then making a guitar to your exact specifications.
At the beginning of the Teisco saga, Teisco instruments were primarily built for domestic consumption in Japan. The early guitars were fairly high quality by contemporary Japanese standards. As the ’60s dawned, Teisco increasingly got caught up in the export market, and by the mid-’60s were major players in the low-end or beginner arena, with instruments sold primarily by mass merchandisers such as Sears and at discount department stores which were rapidly developing at the time. It was mainly in this latter niche that Teisco guitars are known in the U.S. In order to give this narrative some structure, I’ve divided the Teisco history into four basic periods: I-Gibsonia; II-Frumpy Fender-ama; III-A New Spectrum of Originality; and IV-Copydelia.
Just in...We are proud to offer this fine rare example of a Washburn vintage instrument .... This is super guitar! .. Wow talk about some beautiful exotic woods have a look at the Koa sides & back ,its a Solid Sitka Spruce top, Super high AAA grade 3 piece flamed Ribbon Mahogany & walnut neck with the Martin style Diamond Volute on back.... bone nut & saddle this is first class sound & playability & craftsmanship for a song.... Just look at that workmanship.... Great Tone woods with some ager to her now she a real Singer all right... rare to see one of these with such exotic woods makes it specially beautiful. I would compare the feel & tone and volume to that of the Old FG180 Yamaha's very similar ...Just in and its SUPER CLEAN collectors example so get her before she is gone... any questions .... ask please Thanks for your interest and looking....
Vox is a musical equipment manufacturer founded in 1947 by Thomas Walter Jennings in Dartford, Kent, England. The company is most famous for making the Vox AC30 guitar amplifier, used by The Beatles, The Rolling Stones, The Kinks, The Yardbirds, Queen, Dire Straits, U2 and Radiohead, the Vox Continental electric organ, and a series of innovative electric guitars and bass guitars. Since 1992, Vox has been owned by the Japanese electronics firm Korg.
In 1974 Martin Sigma electrics included two SGs, a Tele and a Fender bass. The SBG2-6 was pretty much a straightforward SG copy with a bolt-on neck, center-peaked three-and-three head, block inlays, large pickguard, twin humbuckers, finetune bridge, and stop tailpiece, in cherry. The SBG2-9 was pretty cool, with a natural-finished plywood body, white pickguard, rosewood fingerboard with white block inlays, gold hardware and Bigsby. The SBF2-6 was a Tele with rosewood fingerboard, three-and-three head, block inlays, neck humbucker and bridge single-coil. The SBB2-8 was the bass, with natural finished body, three-and-three head, rosewood ‘board, block inlays, white ‘guard, and two humbucking pickups.
If magnetic pickups are excellent for traveling guitars, contact pickups are great for amplified acoustic performances. These can capture the sound from the soundboard as well as from the rest of the body. You can also get a guitar that comes with a blended system which combines a pickup with a microphone. A model with a built-in preamp is also becoming the norm these days.
For someone who’s been playing for a while, your options are a little different. Perhaps they’ve got a certain guitar in mind. If so, get them what they want! Chances are they’ve already done their homework and have their eye on their next guitar. If they’re not sure, you can still make an educated purchase. There are many popular options that should satisfy most experienced players. And there are many lesser-known models that can be the right fit for someone with more specific tastes.
Breedlove is a semi-recently founded guitar manufacturer that has a main focus of acoustic guitars. Breedlove doesn’t have a massive following like some other brands, so it can be difficult trying to find one to test before purchasing. Breedlove tends to evolve their guitars and tries to push the world of acoustic guitars forward. Their Oregon Concerto Myrtlewood acoustic, for example, manages to produce a big, refined sound and the notes are more resonant. This is due to their tapered myrtlewood body and smaller sound-hole. The body shape is also very important as it’s part of the reason they sound so good and it’s even comfortable to play. All of their guitars are very high-quality and work well for all fingering styles and genres of music. If you want a really great acoustic, you really can’t go wrong with Breedlove.

Some great IR's by Redwirez are available for free at their website as some kind of 25th anniversary thing, and if you use windows you can use VSThost as your "DAW" although all it does is host plugins. It's great because it loads so much quicker than a full DAW and doesn't have all the tricky options that just distract you from playing guitar. Like a real amp, it's plug-n-play (after setting it up, of course--- you'll want to set the sample rate to 192khz so that you can get ~8000 samples a sec with oversampling at 4x on each plugin). It can record, too, so it's a really easy, simple solution. Of course, you'll need a real DAW to mix and master.
I am very pleased with my new guitar, it is perfect... beautifully crafted, comfortable, just perfect for me...Rosewood and spruce and dynamic design ...wow; top of the line case, and the price was substantially less than full price, less than 50%!. There was absolutely nothing wrong with its packaging, as the description indicated. I was a bit nervous thinking it was going to arrive banged up, scratch or damaged, but the box was in good condition and the case was impecable. I got it two days after ordering it, and played it the next day at a school concert. Next will take it to a luthier to get it set, get better strings and an amp. Totally souped! Thanks Amazon for my musical gift for the holidays!

Our pick here is the PAC112V version, for a few reasons. First off, the solid alder body offers you the same tonewood you’ll find in a lot of higher end S-style guitars. The maple neck and diecast tuners will feel really premium in your hands, too. But the 112 series further boosts its value with two Alnico V single coil pickups and an Alnico V humbucker. The addition of the humbucker in the bridge position will open up a whole other world of tones for a budding musician, giving the option for both clean, crisp single coil sounds and thick, high-output humbucker growls.
I have had an old beat-up non-functioning norma electric archtop (hollow body) since i was 13(in 1984). A friend gave it to me and said i could have it if i could fix it... well like 20 years later i fixed it! and had the electrical redone for like $60.00. it needed some new parts (basiclly EVERYTHING) but i really wanted an archtop and knew i could fix this one up to sound pretty cool.... what i have found out about these guitars is that they really arent worth anything... i thought this one may have been from the late 50's early 60's so i may be worth something.. but as it turns out most people i have talked to about restoring it says its not worth anything that they were just little copies made in the 50's-60's and bought in the US at probably sears or something.... oh well I DONT CARE i really like it and its made well, so for the sheer vintage look and great feel I LOVE IT!-jj
What type of environment are you playing in? This is an important consideration when determining how many watts your amp should have. If you practice in an apartment surrounded by neighbors, a low wattage combo option is going to minimize potential conflicts. If you play live gigs in small club environments, it is possible to get by with as little as 50 watts. Larger venues require a larger amp that can move more air with its speaker. You should also take in to account how many other musicians you are playing with, and if there is a second guitarist, as you will want a tone cuts through the mix as opposed to getting buried.
The reason: The dynamic range of music can exceed 60db (power ratio 1:1,000,000). Transients within the music can exceed 20db (power ratio 1:100). Therefore amps under 60Watts and ‘Single Ended Class A’ will not be discussed in this text. Valve amplifiers are used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS systems, audiophile stereo amplifiers, military applications (such as target acquisition and radar) and very high power radio and UHF television transmitters
We’ve all been there, and it’s actually pretty easy to fix once you know how. The reason we hit those walls in our playing or get bored with what we’re currently doing is that we start falling into set patterns with our playing (pentatonic scale over and over again, anyone?). Whatever we’re playing starts to feel stale and derivative because we’ve gone over it so many times, and it can end up being a pretty frustrating experience.
I took it into a local shop to have it looked at, turns out the neck was warped, leading to problem #2 above. I ended up returning it and ordering the same model from a different retailer; although the new guitar didn’t have the same neck problems I ended up having to replace the bridge with a Mastery Bridge (see issue #1, above, the Mastery Bridge cost me another $200 or so, including labor for installation).
Because IRs can be recorded in virtually any space, convolution reverbs generally come with a library of IRs ranging from small live rooms to famous venues, top studio rooms, forests, canyons, railway stations and just about anything else you can think of. They sound very convincing, and there's plenty of variety to be had, but once the IR is loaded, there's only a limited amount of editing you can do without spoiling the natural sound. Usually you can apply EQ and also change the envelope of the reverb decay to make it shorter, and adding pre-delay is not a problem, but after that you pretty much have to take what you get. Some companies, such as Waves, have managed to create additional controls but, as a rule, the further you move from the original IR, the less natural the end result.

Many modern players use the first joint of the thumb against the back of the neck, and almost on the upper binding, sort of like gripping a baseball bat, so they can reach over the neck with their thumb tip to play bass notes on the E and A strings while picking melodies out with the other fingers. Tommy Emmanuel, and Andy McKee are particularly adept at this. You’ll need to experiment some to find what works best for you.
While most collectors aren’t necessarily going to boast that they own a number of Harmony guitars, we shouldn’t forget the important “first axe” role Harmony played for many guitarists. This company took mass production of guitars to the next level. And though you may have to sort through a few to find one that is completely intact and doesn’t allow a car to drive under the strings, they were quality-made instruments for the most part. For those of you who first learned on a Harmony Archtone, this is certainly a childhood treasure!
Martin’s B series basses were big flat-tops with 34″-scale mahogany necks. Designed by Dick Boak, these ABGs used the same bodies as Martin’s Jumbo guitars; measuring 16″ wide with a depth of 4 7/8″, they were large enough to produce decent acoustic volume without being ungainly like other maker’s attempts. The top was solid spruce, the fingerboard was ebony, and the body was either solid East Indian Rosewood (B40) or solid flamed maple (B-65). A Fishman bridge-pickup system was available adding an “E” in the model number. Both basses were also available with fretless fingerboards.
During Michael Laskow's 20-year tenure as an engineer/producer, he worked with Crosby, Stills, Nash and Young, Eric Clapton, Cheap Trick and countless others. He continues to write articles for magazines like Recording and Electronic Musician. He's also the founder of TAXI, an independent A&R company that links record labels with unsigned artists and songwriters.
Decide between mic recording or using a direct box (DI). Recording the sound of your electric guitar by miking your amp is a great way to simulate studio quality sound. However, this will require expensive equipment, like a quality amp, microphone, and potentially sound dampening equipment or material. On the other hand, you can plug your guitar right into a DI to record your guitar.[1]
The roots of the Supro story go back to the ’20s and the sometimes tempestuous relationship between Czech immigrant/instrument repairman/inventor John Dopyera and dapper Vaudeville musician George Beauchamp (pronounced “Beech-um”). Both were searching for the guitar’s holy grail of the era, more volume. Disagreement, and some animosity, has always surrounded the account of just who was responsible for what, but Dopyera ended up building an ampliphonic or self-amplifying guitar (or “resonator” to most guitar buffs) for Beauchamp. John applied for a patent on his tricone design on April 9, 1927, obtaining it on December 31, 1929.
From beginners to seasoned professionals, most guitar players will experiment with effects at some point in their musical journey. While learning to play your instrument well should be a top priority, messing around with effects can be a fun way to engage with your instrument and start learning its sound possibilities without a lot of hard practice. There's a huge variety of stompboxes out there, many with very low price tags that make great gifts and can add a new dimension of fun for beginning players.
We recommend you choose the headstock shape that appeals to you most. The shape of the headstock does not significantly affect the sound or performance of the instrument. Some of our headstock shapes are pointier, which means they can get damaged more easily when dropped or bumped. Choose from our existing shapes, or, send us a drawing of your original design - we can build that, too!
A humbucker pickup is electrically equivalent to two single-coil pickups wired together in series. Coil splitting involves shorting one of the coils to ground, essentially turning the humbucker into a single-coil pickup (not a perfect replica, though, as the magnetic circuits of the two pickup types are different). This is usually done with a DPDT switch, but can also be done with a push-pull pot. Some manufacturers have used a pot to vary the amount of signal shorted to ground from one coil, thus producing a range of tones between a humbucker and a single-coil. Coil splitting results in a sound that's brighter and has less output than a full humbucker. It also eliminates the humbucker's noise-cancelling properties. This modification requires the start and end of both coils to be exposed, which is more commonly available on aftermarket than stock pickups.[17][18]
Though the line between the two is easily smudged, where multi-effects processors create a broad spectrum of effects, modeling processors can recreate the sound of particular instruments and amplifiers, like a Gibson Les Paul played through a stack of Marshall amplifiers, or a Fender Stratocaster played through a Fender Deluxe Reverb amplifier. A modeling processor offers you the ability to make your guitar and amp combination sound like whatever guitar and amplifier sound you want—even if you don’t own either guitar or amplifier. You are limited only by the number of models programmed into the modeling processor when you plug your guitar into one.
Vibrato should definitely be #1. All of those shred heads are choosing sweeps and tapping. I like sweeps and taps, but the vibrato and bends are the best and most important techniques in guitar because not only you can play good, but you can also add soul to your playing. You don't have to tap or sweep to be a better player than the other who doesn't use taps.
Even if your favourite musician is predominantly driven by music and is committed to releasing material for their fans, they cannot possibly deny that are a number of incentives for them to do so. A journalist writing for The Economist online explains that songs are ‘complex mixtures of features’, so composers are always trying to find the right mix of ingredients to increase their chances of success. And everyone loves a success story!
Ibanez is considered to be one of the best-selling electric guitars and bass guitar brands. But, they also produce a quality acoustic guitar for acoustic guitar players. The V series is really popular for newbies, making it one of the best acoustic guitar brands for beginners. Their guitar uses mahogany wood on the neck, and back and sides of the guitar. It also includes a rosewood bridge and rosewood guitar fretboard.
Quality replacement pot from Bourns.   Knurled 1/4" shaft fits most knobs.  Low torque, carbon resistive element, great replacement in many applications using passive humbucker or single-coil pickups.   Note that length of threaded part of shaft is 3/8" - measure to make sure that this is long enough for your application, especially if the pot mounts through the wooden guitar body.   (This pot will not work on Les Pauls, for example).  500K, Special A2 taper preferred by guitar and bass players.  Nut and washer included.   Note: threaded bushing diameter is 3/8", like most 24mm "quarter-sized" pots.

{ "thumbImageID": "S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Satin-Vintage-Sunburst-Black-Pickguard/L01028000003002", "defaultDisplayName": "Sterling by Music Man S.U.B. StingRay Maple Fingerboard Electric Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black Black Pickguard", "sku": "sku:site51500000209679", "price": "299.99", "regularPrice": "299.99", "msrpPrice": "429.00", "priceVisibility": "1", "skuUrl": "/Sterling-by-Music-Man/SUB-StingRay-Maple-Fingerboard-Electric-Bass-Black-Black-Pickguard-1500000209679.gc", "skuImageId": "S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Black-Black-Pickguard/L01028000002002", "brandName": "Sterling by Music Man", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Black-Black-Pickguard/L01028000002002-00-60x60.jpg", "imgAlt": "" } , { "name": "Satin Vintage Sunburst Black Pickguard", "sku": "sku:site51500000209681", "price": "299.99", "regularPrice": "299.99", "msrpPrice": "429.00", "priceVisibility": "1", "skuUrl": "/Sterling-by-Music-Man/SUB-StingRay-Maple-Fingerboard-Electric-Bass-Satin-Vintage-Sunburst-Black-Pickguard-1500000209681.gc", "skuImageId": "S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Satin-Vintage-Sunburst-Black-Pickguard/L01028000003002", "brandName": "Sterling by Music Man", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Satin-Vintage-Sunburst-Black-Pickguard/L01028000003002-00-60x60.jpg", "imgAlt": "" } , { "name": "Mint Green White Pickguard", "sku": "sku:site51500000207686", "price": "299.99", "regularPrice": "299.99", "msrpPrice": "429.00", "priceVisibility": "1", "skuUrl": "/Sterling-by-Music-Man/SUB-StingRay-Maple-Fingerboard-Electric-Bass-Mint-Green-White-Pickguard-1500000207686.gc", "skuImageId": "S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Mint-Green-White-Pickguard/L01028000001001", "brandName": "Sterling by Music Man", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/S.U.B.-StingRay-Maple-Fingerboard-Electric-Bass-Mint-Green-White-Pickguard/L01028000001001-00-60x60.jpg", "imgAlt": "" } ] }


{"eVar4":"used: guitars","eVar5":"used: guitars: electric guitars","pageName":"[gc] used: guitars: electric guitars: supro","reportSuiteIds":"guitarcenterprod","eVar3":"used","prop2":"[gc] used: guitars: electric guitars","prop1":"[gc] used: guitars","evar51":"default: united states","prop10":"condition","prop11":"used","prop5":"[gc] used: guitars: electric guitars","prop6":"[gc] used: guitars: electric guitars","prop3":"[gc] used: guitars: electric guitars","prop4":"[gc] used: guitars: electric guitars","channel":"[gc] used","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] used"}
Just ask any savvy stompbox builder or low-tuned 7-string player: Sometimes the best way to add power to your low tones is to remove a bit of bass. That’s because the lowest frequencies in your signal disproportionately overdrive your amp and effects. Siphoning off just a bit of bass can add clarity and focus. At extreme settings, the filtering can produce sharp, squawking tones akin to those of a ’60s treble booster pedal (not a bad thing). If you’ve ever grappled with high-gain tones that make your amp fart out, here’s your flatulence remedy.
10. Behringer Ultracoustic ACX450 45-watt ($229.99): Not to leave our acoustic-centric players out of the list entirely, the Behringer Ultracoustic not only looks amazing, but it has a ton of features to keep you inspired and sounding great. Two channels are utilized so while you plug your acoustic into channel one, channel two allows you to input a microphone or another source. The FBQ Feedback Indicators allow you to control the feedback coming out of your amp by monitoring the LEDs on the graphic EQ. Need your own guitar effects? The ACX450 allows for 16 different presets on each channel, including delay and reverb. A great bargain for those looking to take their acoustic playing to the next level!
An enduringly popular effect, with all sorts of uses for vocals, drums, guitars and synths, is genuine reverse reverb. This is where a reverb tail appears to increase in volume ahead of the sound that gives rise to it — a completely unnatural sound and something that's impossible to create in real time. It's easy enough to do in a DAW application though. First, find the section of audio you want to treat and reverse it. In the DAW I use, Digital Performer, there's an offline plug-in for this. Now apply conventional reverb to this 'backwards' audio — either by playing it through a reverb plug-in and recording it to another track, or by rendering it using an offline process (if your DAW offers this). In either case make sure you allow enough additional time at the end of the audio to capture the full, final reverb tail. In the screen grab I've done this by allowing 1500 milliseconds of post-roll processing.
You’ll need to get yourself setup with an account on some of the web stores selling components such as effects pedal specialty stores listed above, and some general component stores such as Mouser and Digikey. AMZ provides a list of the components required for each project. Make sure you check carefully the component requirements such as type of capacitors. Many components may have suitable electrical values but different physical layouts, so use the datasheets for your chosen component. Measure the spaces and holes on your PCB to make sure the components will fit. Remember that you’ll also need an enclosure in which to install the finished circuit and don’t forget things such as knobs, battery holders etc.
Jazz guitarists use their knowledge of harmony and jazz theory to create jazz chord "voicings," which emphasize the 3rd and 7th notes of the chord. Some more sophisticated chord voicings also include the 9th, 11th, and 13th notes of the chord. In some modern jazz styles, dominant 7th chords in a tune may contain altered 9ths (either flattened by a semitone, which is called a "flat 9th", or sharpened by a semitone, which is called a "sharp 9th"); 11ths (sharpened by a semitone, which is called a "sharp 11th"); 13ths (typically flattened by a semitone, which is called a "flat 13th").
The Effect:To this day, there are 3 main delay pedal types coexist, Tape is usually the most expensive and sough-after (especially Vintage releases) type as they provide very natural sound reproduction. Analog were modernized in the 70’s and they worked on electronics, with a minor drawback according to some as they store up to 3 seconds of Delay time. Digital pedals is the type met with most frequency on today’s market, offering longer-than-usual Delay times and pristine sound reproduction, these are usually your best pick. A lot of players know that they want a delay effect but have no idea from where to start, if you are one of them, try the Boss DD-7 Digital Delay Pedal The most basic and often met controls on Delay pedals are Time, Level and Feedback, you’ll sometimes find them labeled differently but with the same function and purpose.
We round off this list with a relatively modern innovation in the world of acoustic guitars; the ‘baby’ acoustic. As usual, Martin and Taylor have led the way with these particular guitars, which are effectively shrunken down dreadnoughts which focus heavily on their portability and the wide range of musical scenarios in which they can be used. Martin had dabbled in this world before, with its rather odd looking Backpacker, but it was with the LX1 – and Taylor’s subsequent Baby Taylor – that the world began to take note.
We took another detailed look at all acoustic-electric guitars priced under $500 available from major American online retailers, and for this update, we shortlisted 78 of them for closer analysis. We then collated over 7700 ratings and reviews from forums, videos, retailers, blogs and major music gear publications and processed those data with the Gearank Algorithm to produce a Gearank score of out 100 for each guitar. Finally we selected the highest rated guitars in two of the most popular price brackets, sub $300 and sub $500. For more information about this process see How Gearank Works.
Lotus started with the elite league of Japanese craftsmen and initially made excellent Morris-branded guitars, but trying to keep up with the heavyweights such as Matsumoku Aria Pro II and Fuji-Gen Gakki Ibanez was difficult. Mismanagement and, especially, the inability to market their initial superb-quality guitars soon had Lotus' owners scrambling for cheaper labor, ending in India with poor quality and eventually no takers for their product, as Chinese and Indonesian guitar producers stepped up with instruments of comparable quality at similar prices.
If you use amplifier overdrive, want to use delay and reverb but still crave simplicity—I’d suggest designing a “hybrid” pedalboard. Just run your gain and filter effects in front of the amp, and use a pedal like the TC Electronic Nova System in your amp effects loop for time-based effects. This will require more cabling between your pedalboard and amp, but will sound much better than running your delay and reverb effects into a distorted amp. Pedals like the Nova System or the Eventide units boast specs rivaling studio quality rack gear.
Analyzing the notes you are playing plays an important role while you are performing. The built-in chromatic tuner in these pedals shows you the live feed of your notes whether they are sharp, flat or dead. Similarly, one can bypass the currently selected sound fx for maintaining a pure sound when tuning or completely mute the signal for a uniform silence.
I've had my Dorado, model #5986, serial #41 since 1972 and have used it for classical guitar study off and on since getting it as a gift. For what it is, the sound quality and playability are quite good. I'm donating it to a church rummage sale tomorrow (6/3/07) and will remember it fondly. I have an Alvarez Regency, similar to the Dorado, which lacks the sound character.
A great player knows a guitar is more than a few pieces of wood and metal.  Every Whalehazard guitar is handcrafted with incredible attention to detail and meets exacting standards of quality.  Each instrument is built in South Minneapolis by Andy Webber.  As a one-man operation, great care will be taken to make sure your custom guitar will take your playing and sound to a new level.  All materials and components are carefully selected for quality and longevity.  Designs are painstakingly contemplated and are constantly evolving.  From custom inlays to a hand-shaped bone nut, every detail of your instrument is studied and considered to make sure your Whalehazard guitar is a unique piece of craftsmanship that will stand the test of time.

Although it is well known for its guitars, Gibson's largest business is in fact electronics.[citation needed] Gibson offers consumer audio equipment devices through its subsidiaries Gibson Innovations (Philips brand), Onkyo Corporation (Onkyo and Pioneer brands), TEAC Corporation (Teac and Esoteric brands), Cerwin Vega and Stanton,[6] as well as professional audio equipment from KRK Systems and TEAC Corporation/TASCAM.
A standard Squier Stratocaster is mass-produced in factories located in Indonesia or China. For its construction, Squier usually uses woods readily available in those countries, such asagathis and basswood. They also use stamped metal hardware and multiple pieces of wood in construction to reduce waste and to lower costs. In some cases, the body is laminated, much like a plywood, rather than consisting of two or three solid pieces glued together.
During the 1960s, many musicians[who?] preferred Martin guitars built beforeWorld War II to more recent guitars of the same model. The pre-War guitars were believed[citation needed] to have internal bracing carved more skillfully than later instruments, producing better resonance, and tops made from Adirondack red spruce rather than Sitka spruce. Additionally, 1970s Martin dreadnoughts suffered from poor intonation in the higher registers[citation needed]. Some luthiers and repairmen[who?] attribute this to a gradual trend of misplacing the bridge on these guitars: the same jigs for bridge placement were used throughout the history of each model’s production. As the amount of production increased from the Martin factory, the jigs eroded, resulting in inaccurate bridge placement[citation needed]. This was eventually identified and corrected.
Having Robert Johnson at the top is a joke. All the kids now think it's cool to like him because he was so "influential" but it's a complete myth. He was virtually unknown until the mid sixties and even then the whole "Robert Johnson is cool" thing didn't get going until around 1970, by which time most of the real pioneers were already well on their way.

The best choice for ambient miking is most likely to be a good condenser – probably a large-diaphragm type, though a small-diaphragm type will work. Plenty of ribbon mics give good service as ambient mics also, if you have a clean, high-gain mic pre-amp to track them through. And where do you put it? Well, three or four feet back from the speaker will start to get a significant amount of room sound into the mic, but for more-ambient placements, try six feet or more, and experiment with different heights from the floor, far corners, and so on. One nifty way to find a cool ambient placement is to use your own ear like a mic, and stick the mic at the position in the room where the guitar tone sounds the best to you. This is ideally done with another person playing the guitar; cover one ear and walk around the room listening to the sound in different positions. When you hear a sound that really nails what you’re trying to capture, set up the mic right there. Done.
People sometimes don't really know what they want and use other brands of amps. They haven't found their sound yet and kind of trying other stuff or heard someone or some artist talking of using it and try. But that is not good enough and then they try a Fender. With a Fender you can create your own sound whether you are using pedals or just using the amp and the guitar. A true wonder for every player. Fender's just the best

Add to this the physical attributes and ergonomics of a .strandberg* that work together to relax muscles, joints and tendons when playing. Some players are freaked out by the low weight, others by the lack of headstock and some have a natural playing position that places their thumb right at the edge of the EndurNeck™ and is not comfortable at all.


The Les Paul body style actually encompasses a few different designs: solid, solid-arched, and solid-chambered. Solid Les Pauls are made from a solid piece of wood, with some having a significantly arched top and a maple cap and some lacking a curved top and the maple cap. Chambered Les Pauls are arched, but the inside of the body is chambered, so there are a few cavities underneath the top.
In 1941, CMI became the national distributor for National Dobro products. In ’42, Victor Smith, Al Frost and Louis Dopyera purchased controlling interest in the company. By this time, however, the world was at war and almost all instrument manufacturing ground to a halt as all segments of industry converted to production of materials to support the war effort. In October of 1943, with builders in wartime hiatus, the new owners changed the company name to Valco Manufacturing, incorporating the first initial of each partner’s given name (V-A-L-Co).
A guitar is a stringed instrument that has always been a favorite amongst musicians because it creates symphonic tones that foster creative expression. Guitars are available in a variety of make and brands. In India, the guitar is the most commonly played musical instrument. Since a good guitar lasts for more than a decade, it is important to keep a few things in mind when you are buying a guitar for the first time. There are different types of guitar that are available for buying.
Rickenbacker continued to specialize in steel guitars well into the 1950s, but with the rock and roll boom they shifted towards producing standard guitars, both acoustic and electric. In 1956, Rickenbacker introduced two instruments with the “neck through body” construction that was to become a standard feature of many of the company’s products, including the Combo 400 guitar, the model 4000 bass, and, later, the 600 series.

"Craftsmanship, materials, and dimensional design are combined to make this one of Alvarez' most outstanding models. It has fine projection, sensitive response, and speedy action. The inlaid Tree of Life design on the rosewood fingerboard adds to its graceful distinction. Sides and back of flame grained rosewood are bound with ivoroid. Machine heads are chrome enclosed for longer life. Tuning is fast and precise. Slender mahogany neck with adjustable steel rod reinforcement. The top is select spruce chosen for its acoustic quality."
• How to check frets: The easiest and quickest way to make sure a guitar’s frets are in good shape is to look straight down the neck of a guitar, from body to headstock. If the frets are at different heights (improper installation is the culprit here with new guitars) or askew, there are problems. They should look uniform and exhibit as little denting or wear as tolerable. 

I've played a Telecaster for years exclusively However i have tried playing a Les Paul and i remember thinkin how much easier it was to play. What guitar would you say was the easiest to play? I know it can be subjective but it seems to me that metal guitars are designed to play fast so they are made easier to hit notes etc. I'm guessing something like what steve Vai plays would be so easy and nice to play regardless of tone etc.
To ensure 100% customer satisfaction Bajaao offers 10 day return policy and we also pay for the return shipping to help you be free of the online shopping anxiety. Our content rich page is your one stop to get all the required information about the products be it the product description or the user generated hands on reviews. A friendly and knowledgeable staff is there to help you out with your queries should there be anything else you wish to know about the product, process, payment or after sale service. Our dedicated team will help you to select from the best of the products within your range. Call our experts to find out the best product to suit your style and need and buy electro acoustic guitars at the lowest prices in India.

{"eVar4":"vintage: guitars","pageName":"[gc] vintage: guitars: alvarez","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop18":"skucondition|0||creationdate|1","prop2":"[gc] vintage: guitars","prop1":"[gc] vintage: guitars","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"guitars","prop5":"[gc] vintage: guitars","prop6":"[gc] vintage: guitars","prop3":"[gc] vintage: guitars","prop4":"[gc] vintage: guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] vintage"}
Initially inspired by his older brother Jimmie, Stevie picked up the guitar at an early age and was playing in bands by the time he was 12. By the time he formed his legendary trio Double Trouble in 1980, Stevie Ray Vaughan was already a legend in his adopted hometown of Austin, Texas. After hearing and seeing Vaughan playing at Switzerland’s Montreux Jazz Festival, pop icon David Bowie invited Stevie to play on his Let’s Dance album. Vaughan’s career took off form there.
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Maple - Quilted - Neck Attachment: Neck-through - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Frets: 24 - Inlay: Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black, Diecast, Nickel, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Black, Blue
You can choose between tube amps, hybrids, or solid state models. The first are generally viewed as the grooviest. The latter are cheaper, more reliable, and require less maintenance. And the hybrids are often a practical compromise. (Keep in mind that watt for watt, tube amps are much louder than their solid state cousins with similar wattage ratings.)
Wildwood Guitars is proud to be recognized as one of nine authorized online Gibson dealers. We invite you to browse our extensive inventory and discover the magic of one of the greatest American brands of all time. Located in the heart of Tennessee, the Gibson Memphis factory is known for crafting the majority of Gibson’s incredible semi-hollow and hollowbody instruments. These guitars are overflowing with the soul of the city they’re born in, and they represent the ultimate in both vibe and versatility.
It was a great guitar to learn on, but you are ready for a serious gigging guitar.  Okay, if she was your FIRST love then don't dell her, keep her around for inspiration (plus she ain't worth any money anyway).  Do NOT upgrade her.  Once you start, there will be no end.  Sure great pickups will make her sound great, but you'll also want to replace ALL the electronics, and the tuners, and the bridge, and... well, you get the idea.
Some professional-grade amp heads, such as Ampeg's SVT400-PRO, have an audio crossover, an electronic filter that enables a bassist to split their bass signal into a low-pitched signal (which could be routed to a cabinet suited for low-pitched sounds, such as a 1x15" or 2x15" cabinet), and then send the middle and high-frequencies to a different cabinet suited to this register (e.g., a 2x10" or 4x10" cabinet with a horn-loaded tweeter). Amps with a crossover can either have a single crossover point pre-set at the factory (e.g., 100 Hz) or a knob is provided to enable the bassist to select the frequency where the bass signal is split into low and higher-pitched signal. The SVT400-PRO has a user-adjustable crossover knob. Amps with an adjustable crossover point can enable bassists to fine tune the sound of their bass sound. For example, in some halls, a bassist's usual crossover point may sound too "boomy" or rumbly; turning the crossover knob to send more of the low-pitched bass signal through the 2x10" cab may reduce this problem.
Gibson’s electric guitars generally sport humbucker pickups, known for their thicker, rounder tone. You also get less feedback, which limits the types of delay and overdrive tones you can experiment with, but ensures a cleaner and more consistent sound. Gibson mainly uses mahogany for their guitar bodies, which is what gives it that slightly darker sound.

Our professional guitar technicians inspect each instrument by hand, then perform a full, and precision setup. All brand new guitars need proper setup after shipment to suit your personal preference that would strongly correlate to your playing style. Truss rod adjustments are made to alter the straightness (flatness) of the neck. Truss rods often require adjusting when temperature and humidity change the amount of bow in the neck. Weather, specifically temperature and humidity, may have a dramatic impact on the way your instrument plays. All instrument woods expand and contract with seasonal actuations in temperature and humidity, and naturally, string height and playing action are affected. The neck needs a simple truss rod adjustment to correct any problems like fret buzz and bow neck which can be easily done by guitar experts. And also, you may adjust the bar of bridge. Please be advised that guitar necks are crafted from wood, and they will sometimes shift during shipping and as the temperature/humidity/elevation changes. An important part of maintaining your guitar is knowing how to adjust the truss rod. When a guitar experiences temperature and humidity swings, such as when seasons change, it can develop a slight bow in the neck that results in a guitar that plays buzzy or is suddenly much harder to fret. If this situation occurs, you can often correct the problem simply by tightening or loosening the truss rod. You may bring your brand new guitar in your Local Guitar Shop for proper setup and adjustment of the truss rod.
Eddie Kramer has a slightly different approach, working from a familiar setup of favourite close and ambient mics (including the Beyerdynamic M160 ribbon mic) and then mixing them together to taste. "I use a three-mic technique: an SM57, an MD421 and an M160, all in a very tight pattern. Then I can pick and choose the tone quality, because each mic is totally different. I combine these together, and then I put a U67 away from the amp to get the ambience."
Fender is considered as an American manufacturer of amplifiers and stringed instruments, which was founded by Clarence Leonidas Fender in the year 1946. They provide a wide range of guitar. It has comfortable necks and  smooth fingerboard. Their headquarters located in Scottsdale, Arizona, United States. The guitar will available at Rs. 12,199/- onwards (approx). For further information, visit fender.com.

I have found, like others, that I'm very comfortable with a 9.5" radius Modern C neck. I prefer it if the neck is on the chunkier side of Modern C, but I'm OK with most of 'em. Wider string spacing is helpful too, but would probably be a detriment to someone with shorter fingers. I rarely play fast (OK, I can't really play fast) so a flatter thinner "shredder" neck holds no advantages for me.
Also apparently still in the line in early ’64 was the SD-4L, which had adopted four of the two-tone, metal-covered pickups found on the SS-4L guitar. This still had the old, elongated Strat head. It also had the platform vibrato system found on the previous SS guitars. The SD-4L probably didn’t make it into ’65, but the shape was taken over by the more conventional TG-64.
Slash is a longtime fan of legend Seymour Duncan's hand-wound pickups, and for his new Epiphone Firebird, Slash choose custom Seymour Duncan "Slash" open coil-humbuckers for the rhythm (APH-1) and the lead positions (APH-2). These were Slash's first custom pickups made with Seymour Duncan and feature Alnico II magnets and are slightly overwound for a boosted output. Each pickup has a single conductor cable, a long-legged bottom plate, and a wooden spacer. Controls include individual Volume and Tone pots with traditional Black Top Hat knobs with metal inserts and pointers along with a Switchcraft 3-way Toggle switch. Tone controls for both pickups also feature Sprague "Orange Drop" capacitors (0.022uF, 600V, 5%), the same capacitors Slash uses on his custom designed Les Pauls.
I liked that the test used identical setups and that the results were captured on a high resolution display. Often the debunkers use either their ears alone (and in a MP3 format as well for us to compare) or an oscilloscope which is a terrible measuring device for real sound because it can only display time and amplitude where the amplitude is a summed view of all the frequencies at the same time. The FFT clearly showed much much more.
{"product":{"id":"451058","stock":"instock","price":"9.99","name":"Electric, Acoustic and Bass Guitar Stand","download":false,"sku_id":"451058000001000","checksum":"12742902520","rep_id":"site5127474174231345694","displayId":"127474174231345694","sku_display_id":"1274228076940","sku_rep_id":"site51274228076940","gc_pro":false},"category":"Stands & Racks","pageName":"product_detail","subcategory":"Guitar Stands & Wall Hangers","dept":"Accessories"}
A soldering iron is basically a tool that allows you to transfer heat that in turn melts the solder which is used to join two pieces of metal. The heat is supplied electrically (this wasn’t always the case) and the soldering iron itself will have an insulated handle protecting you from the heat generated. For some useful tips on best practice for soldering click here: https://guitarkitworld.com/common-mistakes-to-avoid-when-building-an-electric-guitar-kit/

: : : Does anyone know for sure where these originated. I have been told Vox (the England years) made this flat bodied plank guitar in the skiffle days of early 60's/late 50's. Mine is painted white(by hand) with a large black pick guard that curves to envelope the two chrome "toaster" pickups ,bottom of neck, and three control knobs.The strings have a moveable maple bridge(not secured) and a small chrome hardtail heel.The neck has a zero fret at top and 19 more playing frets.There are dot inlays at the 3rd,5th,seventh,ninth,12th,and 17th frets.The headstock is of natural finish light maple with a top edge cut at a sloping angle like Hofner.It has brass tuning pegs,gears and gear plates and the keys are white plastic.The beautiful short neck is true ,natural maple.Along one of the tuning gear plates is the numbers: 35515 which are etched into the wood. Four bolts without any plate hold the neck base to the plain body and a green decal above the pegs at top face of headstock reads: Shadow. The fret board is rosewoodand is laid on neck without bindings.It has six strings and sounds like a short scale Baritone guitar. It also only has one strap peg at bottom since they used to put the other end of strap on a tuning key. No other holes are seen for any former peg at other end of body(where normally found). Please send any info on this small,early,simple but awesome sounding electric skiffle guitar from England(Vox?).Thanks!!!!! VoteinNovember
×