When the tone pot is set to its maximum resistance (e.g. 250kΩ), all of the frequencies (low and high) have a relatively high path of resistance to ground. As we reduce the resistance of the tone pot to 0Ω, the impedance of the capacitor has more of an impact and we gradually lose more high frequencies to ground through the tone circuit. If we use a higher value capacitor, we lose more high frequencies and get a darker, fatter sound than if we use a lower value.
In typical pedal effect chains you will most likely be running cable lengths that are much longer than 5.5 meters. The ME-80 allows you to keep your tone pure when running lots of effects. You can run a cable up to 5.5 metres into the input of the ME-80. The multi effects engine processes up to 8 effects in its internal signal chain. Then the ME-80 outputs your guitar signal as a 2,000 Ohm low impedance signal allowing you to run a much longer cable to the amplifier.
The lower portion is reserved for two footswitches – each for one of two available effects. It’s a busy stompbox, that’s for sure. However, the versatility it offers is hard to top, and the tone quality is definitely on a high level. Depending on how serious you are about your reverb, Mooer TVR1 Shimverb Pro (click for full review) can be a real force multiplier if used correctly.
{"pageName":"[gc] pdp: epiphone les paul special vintage edition electric guitar","reportSuiteIds":"guitarcenterprod","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","events":"event3,event45,prodView","evar51":"default: united states","prop5":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop6":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop3":"[gc] shop: guitars: electric guitars: solid body electric guitars","prop4":"[gc] shop: guitars: electric guitars: solid body electric guitars","products":";J40301;;;;evar65=New-Guitars-Epiphone","linkInternalFilters":"javascript:,guitarcenter.com","channel":"[gc] shop","prop7":"[gc] product detail page"}
Now, to answer your question I would have to point out a series of popular brands and what they are popular for. After that, you make a decision on which one is best for you. You might see where I’m going with this. There is no single best guitar brand the same way there is no single best car brand. But we do have the Ferraris and Lamborghinis, as well as the Toyotas and Nissans of the guitar world!

Del Rey, of course, is Spanish for “of the king,” which explains the crown. This was no doubt added to the Teisco name, in part, to suggest quality. However, it was also a way to add the de rigeur Spanish cachet necessary for “Spanish” guitars of the time. It was convention that “Spanish” guitars carried Spanish names, except for the well-known brand names – Gibson, Fender, Martin or Kay; thus the plethora of imported guitars named Greco, Ibanez, Goya and Espa�a. Of course, none of these were made in Spain, but rather in Japan, Japan, Sweden and Finland, respectively!

Overall, the reviews and comparison should not be the criteria on which you should decide the brand that you want. The best way to choose one is by listening to and feeling the sound that the guitar produces. The brands listed above are some of the best-known in the world. Of course, there are many other good brands out there too. If you feel we've missed out on some, please feel free to mention them in the comments section below.
Guitar Center Fort Worth provides comprehensive guitar repair services for the Fort Worth area. Our repair technicians are as passionate about your guitars and basses as you are, and we have the experience needed to keep them performing at their best. Whether you need a quick adjustment to make your guitar easier to play, or a complete guitar rebuild, we have the tools and know-how to take care of your instrument. Guitar Center Fort Worth can also help build a maintenance plan that fits you and your guitar or bass needs, including custom setups, restrings and more. We also take care of fret repairs, hardware and pickup installations, upgrades and customizations, bone and graphite services and more.
The output jack is where you plug in your guitar lead. These are generally 1/4″ and transfer the signal created by your pickups to your guitar amp. They are usually connected from a ground wire and input wire. When the lead is plugged into the output jack the signal can be transferred. These can often be a source of trouble and need to be kept tight to reduce noise.
Now, let’s get to the amplifier. If you’re a traditionalist, this means you aren’t using some kind of high fidelity audio reproduction system to expose that weak signal for the anemic, naked thing that your tone really is at this point. You’re like the rest of us, depending on that signal working with a classic tube guitar amp to shape your sound and help you get awesome and loud. Well, that amp has got a host of things going on. The signal hits the high-impedance input and visits the preamplifier. See, the “natural” sound coming straight from our guitars, as big and tough and old school special as we might think think it is, really isn’t strong enough to directly power the power amplifier. It’s depending on a series of fairly intricate pre-amplifer gain stages to give the Popeye signal the spinach it needs before any filtering or equalization (oh, they don’t use them? Really? What do those knobs marked ‘bass’ and ‘treble’ say? Just because someone leaves them at “5” doesn’t mean they aren’t in use). It then may visit a phase inverter before hitting the tube power amp section, which finally gives you the high current signal to cause those speakers to go back and forth.
{ "thumbImageID": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "defaultDisplayName": "Ibanez RG6003FM Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Flat Sapphire Blue", "sku": "sku:site51409670719560", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue-1409670719560.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Sapphire-Blue/J07945000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Flat Transparent Gray", "sku": "sku:site51393862854365", "price": "279.99", "regularPrice": "349.99", "msrpPrice": "466.65", "priceVisibility": "1", "skuUrl": "/Ibanez/RG6003FM-Electric-Guitar-Flat-Transparent-Gray-1393862854365.gc", "skuImageId": "RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/RG6003FM-Electric-Guitar-Flat-Transparent-Gray/J07945000001000-00-60x60.jpg", "imgAlt": "" } ] }
On guitars with bound fingerboards, shrinking of the binding can produce a gap large enough to catch the treble E string when pulling it over the edge. If only a few our present I will fill the gap to eliminate the problem. If the binding shrinkage has introduced gaps at every fret, the board should be re-radiused to eliminate all gaps and re-fretted.
Flat tops from 1970 to present are considered to be excellent utility instruments, but are not collectible. Staring in 1976, Martin has been undergoing many changes with numerous reissues, new models, limited editions, etc. Workmanship has improved greatly from the early 1970's, and Martin is now producing some of its best guitars in over 20 years. While not currently collector's items, these intruments have excellent workmanship, sound, and playability.
We carry many new and ‘lightly’ used instruments. So called “low mileage” instruments, in near mint condition, are our specialty. Currently in house: Santa Cruz, Bourgeois, Eastman, Fender, Larrivee, Martin, Epiphone, Gibson, Gretsch, Guild, Giebitz, Huss & Dalton, Sobell, New World Classical Guitars, Cordoba Classical Guitars, Loar, Recording King, G&L, LsL, Breedlove. Amps from Magnatone, […]
You are right, we will have the whole guitar amplifiers section of out website completely revamped in the next few weeks! We made vast content improvements on all other sections of GuitarFella and now it is time to work on the amps. Thanks a lot for the remark and make sure you check us out in 2-3 weeks, I guarantee you that you will like the results!
What if you could get a wide variety of sounds from your acoustic guitar, including complex effects and virtual (MIDI) instruments, without having to use an external amp? That would certainly be a game-changer, as it could essentially turn your guitar into an all new instrument, and by adding to your available 'soundscapes' without needing to be tethered to a plug, it could also convert acoustic performances into rockin' ones.
Five string guitars are common in Brazil, where they are known as guitarra baiana and are typically tuned in 5ths. Schecter Guitar Research produced a production model 5 string guitar called the Celloblaster in 1998.[43] A five-string tuning may be necessary in a pinch when a string breaks on a standard six-string (usually the high E) and no replacement is immediately available.
DRILLING THE NECK HOLES ON THE BODY Before you do this you can carve down the back of the neck area if that is something you were going to do. If you are just going to leave it flat then that's ok too. The first step if you are using furreles is to map out where you want to place them and then mark the center of the hole where the screw will go. Then take your forstner bit drill enough to fit the furrele inside. Usually you can tell how deep to go if you drill a little at a time, and place the furrele in it to see if it is just low enough in the hole not to see the top of it if you look at the body horizontally or it is flush with the wood. After doing this you can drill the holes for the screws. Use a bit that has the same circumference as the screw including the threading so when you put the scre into the hole it just passes through with out you having to screw it in. Drill in the indention that was left by the tip of the Forstner bit, keeping the drill as straight as possible.
Read Full Review It’s amazing to see a company that excels in all the products and services they offer, while other companies are struggling and scratching their heads to find a way to break through in the market. The best example of such success on Yamaha is with their long line of guitars and two of those guitars they have are considered by many is best for beginners. The guitars I’m taking about is the Pacifica Series PAC112 together with the PA012 featured here, which is also available on a guitar package.

I just recently started to try to" really learn" to play guitar. I've known a few "not too difficult" songs for years. Now at 45yrs. old I bought a couple of cord books and it's bittersweet. It's such a wonderful feeling to play songs all the way to the end with a friend of mine who told me years ago that I had a good natural musical ability. I've learned more in 3 or 4 months than in 25 years. But enough about that... I was handed a jumbo GUILD from I believe around the early 70's. I've never heard anything like it. I must have one!!!
ARTIN IS NOT THE BEST ACOUSTIC GUITAR. Any Taylor of the same price range WILL BEAT THE BRAKES OFF A GUITAR IN THAT SAME PRICE RANGE! In fact, most profession guitar players switched from Martin to Taylor for that reason Dave Matthews Clapton jack Johnson BUT MARTIN OR TAYLOR ARE THE LEADERS IN THE ACOUSTIC GUITARS! Epiphone master built is another great choice if you are looking for a great 3-500 price range..the ONLY REASON THEY DONT COMPETE WITH MARTIN IS BC FEW PEOPLE KNOW ABOUT THEM! You can buy a Martin that sounds just same but you'll triple the price! Alvarez yari is another well built wonderful guitar but again &1000-1300 against the epiphone masterbilt. Low price great sound go masterbilt about anything else go Taylor
I dont know but im looking for a good bass guitar too. Depends on your price range. Personally I realy like Ibanez basses and think they do really good low to mid price range basses. If you are looking at a professional quality basses you should look at Rickenbacker, Musicman (stingray), Fender, Lakland and Shadowsky as they are the main brands for professional basses.
Yeah. The tremolo sound from the intro? That was four Fender Twin Reverbs. Myself controlling the speed of two of them and the producer controlling the speed of the other two. So two amps were recorded on one side of the stereo and the other two on the other side. I recorded the part on the tape without the tremolo, and then I sent the part from tape out to four amps, and he controlled two, and I controlled the other two.

There’s an old joke in the technology industry: If a product has a problem, simply sell it as a feature. The electric-guitar-effects industry is no different. Music has often thrived on transforming faults into influential sound effects. Before professional studio production enabled granular tweaks in sound, standalone guitar effects emerged from deliberately converting hardware faults—often caused by the limitations of amplifiers—into positive features. By the end of the 1970s, it had become impossible to imagine how R&B, blues, and rock could have existed without these fortuitous mistakes.

A combo amplifier is a unit in which both the amp and speaker is integrated. You plug a guitar into one of these, turn it on and you are ready to play. The obvious benefit of a combo is that you have everything you need in one standalone unit, while the sound tends to be optimized by the manufacturer to be the best it can be – there’s no worrying about matching it with a good speaker. Combo amps also tend to be cheaper than heads and, as such, are excellent for beginners. While some are very capable of small to medium-sized performance, the drawback is that combos are limited in power compared to a head. They also tend to be much heavier, which can be a pain when regularly transporting it.


Just for fun, try taking this inverted approach to setting string height: instead of getting them as low as you can without inducing serious buzzing, set your strings as high as you can have them and still be able to play with some reasonable facility. Doing this correctly might also require adjusting string intonation at the bridge saddles, because their angle and distance across their speaking length is now changing slightly, too, but for now just try it as is, in case you choose to return your action to point one. (Note that raising string height at the bridge might need to be coordinated with a tweak of neck relief at the truss rod, although I will leave that to your own best judgment as there is plenty of debated between the flat-neck/slight-relief crowds, and this determination will depend upon your own preferences.)

Bill Collings dropped out of medical school in the early 1970s[3] and instead worked in a machine shop for five years.[4] At the same time he built his first guitar. In 1975 he moved to Houston, Texas, where he worked as an engineer with a pipeline and oil field equipment company by day and a guitar builder by night. Three years later he met renowned musician Lyle Lovett and built him a guitar.

I'm no pro, but I take my time when I'm buying a guitar. I played everything, and for feel, sound and playability, I was about sold on a Gretsch 6119 vintage remake. Then I played an Eastman TX 186. Hollowbody constructed from all solid wood, better pickups than the Gretsch, and just fantastic tone that gets better the more I play it. And it cost about 60% what the Gretsch cost - not an entry level price, but a guitar I won't get tired of playing. They deserve to be better known. Some of the Epiphones and most of the Ibanezes felt and sounded cheap in comparison.
While other Univox brand amps may have existed during this period, these are the only ones on our radar scope. The brand was still being put on amps as late as 1976, and all of the later amps were still in a 1980 binder, though by ’79 only two Univox amps were listed in the price list. Most likely, when the Univox guitars went away in ’77 or ’78, so did the Univox amps, but supplies probably continued to be available as late as 1980. Anyhow, this sets the stage for the next development in amps to which we’ll come back…
Gain is the strength of the electronic signal carrying your sound. A standalone gain booster is essentially just a preamp, and can be an effective way to overdrive the preamp section of your amp, creating easier musical-sounding breakup and increasing the amp's power. A gain booster in a stomp box lets you instantly boost your sound level for solos without altering your fundamental tone.
The conservative way to tell if a Martin is built for steel strings is the bridge. If it's a style 18 or higher and has a belly bridge (and does not have 'banjo' tuners like early OM models), it's pretty much built for steel strings (can't use this indicator on style 17 and lower as these models never used a belly brige until the 1950s). Why? Since Martin didn't implement the belly bridge until late 1929, it's a very conservative indicator that the guitar is built for steel. The belly bridge was the last thing they did to make steel strings usable on their guitars (though certainly many models with rectangle bridges can handle steel strings too.) They started to implement the belly bridge in 1929, and all style 18 models and higher had the belly bridge by 1930. Therefore using the belly bridge as a steel string indicator is a very safe idea (assuming the bridge is original and it's not an OM). Now can steel strings be used on pre-1930 models with a pyramid or rectangle bridge? Maybe, but it's just not as definative and caution should be heeded ("silk and steel" strings would be a good and safe compromise). Note early OM models with banjo style tuners generally should be strung up 'lightly'.
20 pages, black and white with color front cover. In the middle of 1981, Rosetti took over distribution of the Gibson line in the UK. Rosetti were a very big name in Britain, having distributed Epiphone since at least 1963, as well as Hagstrom and others. This catalogue was produced at the tail end of 1981, and introduces a number of models to the UK, such as the MV-II, MV-X guitars and the Victory basses, the GGC-700 and the Flying V bass. Some of these models were so short-lived that they were actually never included in US brochures. The cover image (reproduced in part here) showed some of the earliest demonstration models, including a Victory with a highly unusual white scratchplate.

While jazz can be played on any type of guitar, from an acoustic instrument to a solid-bodied electric guitar such as a Fender Stratocaster, the full-depth archtop guitar has become known as the prototypical "jazz guitar." Archtop guitars are steel-string acoustic guitars with a big soundbox, arched top, violin-style f-holes, a "floating bridge" and magnetic or piezoelectric pickups. Early makers of jazz guitars included Gibson, Epiphone, D'Angelico and Stromberg. The electric guitar is plugged into a guitar amplifier to make it sound loud enough for performance. Guitar amplifiers have equalizer controls that allow the guitarist to change the tone of the instrument, by emphasizing or de-emphasizing certain frequency bands. The use of reverb effects, which are often included in guitar amplifiers, has long been part of the jazz guitar sound. Particularly since the 1970s jazz fusion era, some jazz guitarists have also used effects pedals such as overdrive pedals, chorus pedals and wah pedals.
Electric instruments have a big role to play in the world of music, but there's a catch: they need amplification to do it! For that matter, even acoustic instruments need to be boosted when they're playing big venues. And while an amp alone can handle those tasks, many of the sounds in modern music (the signature distortion of rock and metal, for instance) rely heavily on effects units to shape the basic tone into something even better. If you're new to your instrument, then consider this selection of amplifiers and effects the doorway to your future sound - and your instrument will be the key that opens it up, once you've got your hands on your brand new hardware!
I once did a setup on one that belonged to a friend but it was really wrecked so it wasn't perhaps a fair representation. It seemed to be well built though and the neck was nice enough. The tone was decent too although not exciting - exactly what you'd expect from such a guitar. Overall I'd say it was better than the cheaper squiers (SEs, Affinities etc).
Those items considered -- performance notation and computational capacity for emulation of stringed instrument sounds otherwise reinforced by the same speaker systems that amplify synthesized sounds -- the other significant factors in the realism matrix involve economics of VST production, listener preferences and, least we forget, performer or producer preferences.
The varying amplified current of the valve is connected through the first coil of wire (primary) and creates a varying magnetic field. The varying magnetic field created by the primary coil, causes electricity to be generated in the second coil of wire, which is wound tightly around the first. Electricity is transferred to the second coil only when the magnetic field is changing, not stationary. The iron core of the transformer keeps the magnetic field contained so little is lost. The transfer is very efficient. The secondary coil is connected directly to the speaker. The reduced secondary voltage is adjusted by the ratio of turns between the 2 coils. Eg 1,000 turns on the primary and 100 turns on the secondary would change the voltage 10:1. Most output transformers have a turn’s ratio of approx 20:1.
Interesting site.I searched make before break and you appeared.Ive just bought a Squier Classic Vibe Butterscotch telecaster and it has stock Alnico 5 pups. It got me remembering how, back in the 1960s I used a standard U.S. Tele and did the jamming in between thing. If you were careful it balanced and held in place.I always loved that position. I think, if I remember correctly, you could get between bridge and both and also neck and both.I think it was a superior sound to any 5 way switch I’ve heard. Is it possible to modify my make after break classic vibe switch to make before break or do I need a new switch? And can you buy make before break switches for a 2 pup Tele ? Thanks much.Mike.U.K.
Most electric guitars feature multiple pickups. Some will have two or three single-coils. Some will have two or three humbuckers. Many offer a combination of single-coil and humbucker pickups. This combination offers the player a wide range of tonal options. Pickup configurations are often abbreviated by referring to single-coils with an "S" and humbuckers with an "H." The placement of each pickup is indicated from the neck down towards the bridge. Thus an SSH configuration has single-coils at the neck and middle positions and a humbucker at the bridge.
Then, as the most popular version goes, a young, jack of all trades guitarist named Les Paul got tired of all that. So, he set out to create a guitar that could be heard just as much as the louder instruments. He fiddled with a lot of electronic means to boost his sound. Some worked better than others. His piece de resistance at the time would come to be known as "The Log". It looked like what you see up there on the left:
This Hellraiser C1 guitar features a mahogany body and a quilted maple top and abalone gothic cross inlays. It looks and feels fantastic! A couple of things that make it sound even better are the locking tuners, that keep it in tune, and the EMG noise-cancelling scheme that makes sure that the only sound the guitar makes is the music you’re playing.
This is our new cross-reference between classic pedals (e.g. a Fuzz Face) and who makes kits or boards to build it yourself. In some cases the kit or board is for an exact clone. In others, it is for a circuit based on the original but with improvements or combinations with other pedal designs. Read the description specifics by clicking the link and visiting the maker’s site.
The epic storylines, adrenaline-pumping action and explosive thrills are back. The Fallout franchise returns with Fallout 4. Grab your controller and get ready to dive back into the enveloping storyline of this legendary series. Get ready to return to the epic, award-winning franchise with Fallout 4. This newest chapter brings an all-new open-world environment to life, and has been created by Bethesda Game Studios, creators of Game-of-the-Year-award winners Fallout 3 and The Elder Scrolls V: Skyrim. Will you be prepared for the next Fallout installment?

A far cry from just another mass produced vintage looking guitar, the Kay Vintage Reissue Series successfully duplicates the original 50's models, within feel, playability and the legendary Kay sound. Complete with the company's gold chevron, flagship headstock design, displaying 3-D raised "Kel-von-a-tor" style emblem, to this day, the Kay Thin Twin Electric Guitar is probably one of the coolest looking guitars ever made.

Now think about all the advances in guitar technology that we’ve witnessed over the decades—how much smarter we are now when it comes to acoustics, electronics and precision manufacturing? Sticking with this metaphor, isn’t it a bit crazy that we place such high value on the early designs that represent the Model T-era of the electric guitar’s evolution? We’re not just talking nostalgia and historic significance here—ask most guitarists to name the most amazing, best-sounding electric guitars ever made, and they’ll go all the way back to early-fifties Broadcasters, late-fifties Les Pauls, and early-sixties Stratocasters. Guitarists cling to the tones produced by what is, essentially, first generation technology.


Apollo, Aquarius, Arbiter, Atlas, Audition, Avar, Ayar, Barth, Beltone, Black Jack, Cameo, CBS, Cipher, Concert, Cougar, Crown, Daimaru, Decca, Diasonic, Domino, Duke, Emperador, Heit Deluxe, Holiday, Ibanez, Imperial, Inter-Mark Cipher, Jedson, Kay, Kent, Kimberly, Kingsley, Kingston, Keefy, Lindell, Marquis, May Queen, Minister, Noble, Prestige, Randall, Recco, Regina, Rexina, Sakai, Satellite, Schaffer, Sekova, Silvertone, Sorrento, Sterling, Swinger, Tele Star, Top Twenty, Victoria, Winston
CALIFORNIA CLASSIC models feature superb playability, distinctive looks and an unmistakable Fender vibe. The fully-painted solid Sitka spruce top and natural solid mahogany back and sides, as well as a matching painted 6-in-line headstock and koa binding and rosette, give them an elegant two-toned aesthetic that was made for the stage. California Special and California Classic acoustic guitars are equipped with a Fender- and Fishman-designed PM preamp specifically tuned to complement the unique shape and voice of each instrument—complete with tuner, frequency and phase controls.
Semi-hollow body electric guitars are basically a middle ground between a solid body electric and a fully hollow body electric guitar. Jazz, country, and rock guitarists alike may gravitate towards semi-hollow body electric guitars for several reasons. One of the main reasons is that semi-hollow body guitars still produce that rich, resonant sound of a hollow instrument, but they typically have a solid or sometimes chambered center block in between the top and back. This design helps fight off that unwanted body-resonant feedback we spoke about before while even adding some extra sustain. Gibson offers a wide selection of semi-hollow body electric guitars, which include the iconic Gibson ES-335. Guitar brands such as Gretsch and Ibanez are also widely recognized for their semi-hollow body electric guitars.
×