Unintentional phase cancellation can also occur if a guitar's pickups are wired incorrectly, or if a new pickup installed in the guitar has different magnetic or electric polarity from the one it replaced. To fix this, the pickup's magnetic or electric polarity needs to be reversed (which one exactly depends on the respective polarities of the other pickup(s) and whether or not hum-cancelling combinations are desired). While the latter is usually a small matter of reversing the pickup's hot and ground wires,[24] the former may be more difficult, especially if it requires the magnet(s) to be removed and reinstalled in a different orientation, a process which can damage the pickup and render it unusable if not done carefully.[25] This is the case with most humbuckers. On the other hand, single-coil pickups with magnetic polepieces can simply be repolarised by applying a strong enough external magnetic field.

i've got a a Ricky Tom Petty model (same as the 660-12) that I've had for almost 20 years. Plays great and the sound difference compared to a 360 is minimal, and I like it better because it has the old toaster pickups. The only thing I had to do it was pull off some of the windings on the pickups. They were up to 12K ohms, which is very high and makes the guitar sound too thick. Unwound to about 8K and they sound much better. I had a different Ricky with the narrow neck and it was painful to play at best with my fat fingers. The wider neck is a dream to play.
Distortion sound or "texture" from guitar amplifiers is further shaped or processed through the frequency response and distortion factors in the microphones (their response, placement, and multi-microphone comb filtering effects), microphone preamps, mixer channel equalization, and compression. Additionally, the basic sound produced by the guitar amplifier can be changed and shaped by adding distortion and/or equalization effect pedals before the amp's input jack, in the effects loop just before the tube power amp, or after the power tubes.
After I published that blog post, a number of beginners wrote to tell me they had a higher budget and would actually like me to recommend some better beginner guitars than those you typically find in starter packs. When I dug deeper, most told me they had a max budget of about $300 for the guitar alone, and weren’t interested in all-in-one starter packs. They wanted a really great (but affordable) guitar and wanted to shop for amps and accessories separately. I further confirmed this with a little informal poll on Twitter:

Peerless hollowbody guitars are excellent at this price range. Both of these brands manufacture from factories in South Korea. PRS SE is made by World Instruments Co. and they have consistently high standards - all brands made in this factory will be exceptional. Peerless is a company which used to manufacture high end guitars for other brands such as Gretsch and Gibson, and then launched their own brand. They are exceptionally good guitars.
Notch filters (also called band-stop filters or band-rejection filters) are sometimes used with double basses. Notch filters are filters that allow most frequencies to pass through unaltered, while attenuating those in a specific range to very low levels. Notch filters are used in instrument amplifiers and preamplifiers for acoustic instruments such as acoustic guitar, mandolin, and bass instrument amplifiers to reduce or prevent feedback. While most notch filters are set manually by the user, there are also automatic notch filters which detect the onset of feedback and notch out the frequency before damaging feedback begins.
Good looks and playability seem to be the two biggest selling points of the Ibanez AEG10II. Many describe it as a fun instrument, thanks to its comfortably thin profile body and fast action setup. A good portion of its positive reviews are from users who after gigging with the guitar, have great things to say about its reliability and amplified sound.
Similar to the previous model we mentioned, Squier by Fender Bullet Strat represents the Stratocaster beginner family. It’s a guitar full of tradeoffs, but you are rarely going to find a model more capable in this price range. I’ve played a lot of these, and even have one which I use strictly for practicing at home. I like it, even though it’s somewhat limited.
The aim of Audio Issues is to help interested newcomers get started in the world of audio production with easy to use practical audio production tips for beginners and advanced. If you are just starting out doing some home recording or have been engineering for a while, these quick and easy audio tips are guaranteed to be of interest and use to you.

* The guitar has a mahogany neck, but a basswood body. Do not let anyone tell you this is a bad thing. Basswood is a completely acceptable wood for musical instruments. It is not worse or better than mahogany or maple. It is just different. Once again, the differences involved will probably be irrelevant when added into all the other things that players do with amps, strings and pedals to create tone and sound from an electric guitar.


This is another best budget electric guitar from Epiphone. It is also a great choice for a beginner and it is quite lightweight to carry. For an inexpensive guitar, this one has a pretty good sound and tone. Despite being low priced, the manufacturer has not compromised in its quality. The cherry red color is really attractive and appealing and can help you to boost up your smart personality as a guitarist. This is closer in look to the iconic rock guitars.
Remember, when you choose to buy an electric guitar by itself (not as part of a ‘starter pack’), you’ll also need to buy an amp, guitar cable, and a tuner. These are extra costs that you should budget for on top of the cost of your new guitar. I recommend that beginners keep their first amp purchase conservative–both in price and size. Here’s what I’d recommend:
Stacking the C-major scale with thirds creates a chord progression  Play (help·info), traditionally enumerated with the Roman numerals I, ii, iii, IV, V, vi, viio. Its major-key sub-progression C-F-G (I-IV-V) is conventional in popular music. In this progression, the minor triads ii-iii-vi appear in the relative minor key (Am)'s corresponding chord progression.
The first of the easy guitar chords for beginners is E minor, followed by E major. Next you learn A minor and C major, all in the open position, which means the chords contain open strings and are played at the nut position. The next chord is D major, followed by A major. You will learn the B major chord, which is a barre chord with the root note on the A string. After this you learn the B7 open chord, which sounds really nice.
Description: Body: Maple - Top Wood: Spruce - Neck Attachment: Set - Neck Wood: Maple - Neck Construction: 3 Piece - Fingerboard: Ebony - Frets: Medium - Inlay: Acrylic & Abalone Block - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 3+3 - Bridge Construction: Ebony - Cutaway: Single - Hardware: Gold, 2x Volume Control, 2x Tone Control - Pickups: GB Special - Pickup Configuration: H-H - String Instrument Finish: Brown Sunburst - String Instrument Accessories: Hardshell Case
Gibson’s drive to recapture the magic of the original “Patent Applied For” humbucker pickups of the 1950s culminated with the introduction of the Burstbucker line in the early 1990s. In 2002, Gibson followed up this innovative accomplishment with yet another breakthrough in pickup design—the Burstbucker Pro, designed specifically for the new Les Paul Standards. The Burstbucker Pro features an Alnico V magnet (instead of the Alnico II), which offers slightly higher output and allows preamps to be driven a little harder to achieve a more natural break-up. Like all Burstbuckers, the Burstbucker Pro has asymmetrical coils—true to the original PAFs—which supply a more open sound. The Burstbucker Pro Neck is wound slightly less than the original PAFs, while the Burstbucker Pro Bridge is slightly overwound for increased output. The Burstbucker Pro pickups are also wax potted to allow loud volume pressures with minimal feedback.
One notable exception is a pitch shifter or harmonizer, particularly if you plan on using a pitch shift and envelope follower together as the pitch shifter may have greater difficulty accurately tracking an envelope follower-processed signal. Similarly, a standard wah pedal generally sounds best in the very front of the signal chain, but once again I recommend placing pitch shifter/harmonizer effects in front of a wah if you plan on using both together. Also, many players prefer the sound of a wah with a distortion pedal placed in front of it as this configuration can produce a more dramatic or more refined sweep depending on the distortion pedal’s tonal character (See Example 1, below).
While a straight DI approach can work for clean sounds, simply plugging a guitar into an overdrive pedal and then routing the output of the pedal into your recording system will sound unnaturally thin and raspy because there are no speakers to take away the unwanted high end, but that hasn't stopped some people using it as a 'trademark' sound! For a more conventional sound, a speaker simulator is needed to filter out the unwanted higher harmonics. A passive speaker simulator, such as the original Palmer Junction box can be placed directly after an overdrive pedal or a regular guitar amp preamp output, but it will need to be recorded using a mic input rather than a line input (passive filtering always results in a reduction in level). Active equivalents (usually battery or phantom powered) are also available, which may offer a greater range of tonalities.
As a general rule, I'll set up the 57 right against the amp's grill cloth, pointing it directly in to the speaker (sometimes at a slight angle from the outer rim of the speaker pointing toward the center). I'll usually place a condensor about two to three feet in front of the amp (at the same level as the amp) and point it at one of the speakers, and if I have another condensor available, I'll place it about five or six feet away, in front of the amp. I'll also raise the "far" mic to a height of approximately five or six feet off the ground.
If the Complete Technique book is good for quick starts, this would be the bullet train. Another Hal Leonard selection, this is a trim 48 pages for teaching you how to hold a guitar for the first time. Tuning up, easy chords, and strumming. If you got a guitar on Friday, use this to put together your first three-chord jam by Monday. Will it sound good? No, no, it will not. But you’ll have started, which is key. Some of the other books on this list are dense with both concepts and pages, which might delay your starting. Don’t let that happen.
Now, since I have started on my wishlist there is another thing that I would like to add. I have seen multi angle videos that include a shot the finger board from the point of view of the player. Looking at this video angle it shows the fingerboard from the same angle as when you are playing it yourself. This is a great view as you do not need to translate what you see mentally. You see it, you play it the same way.
"My part is just a few notes over and over," Iggy Pop once said about the Stooges song "TV Eye," "but Ron created a whole world around that." In Asheton's hands – on proto-punk anthems like "I Wanna Be Your Dog" and "No Fun" – the classic three-digit barre chord felt more like a superpowered battering ram: droning, relentless and almost mystical. (Asheton, who died in 2009, called it "those magical three fingers.") You can hear Asheton's wild-man approach all over the playing of Kurt Cobain, Thurston Moore and Jack White.

In Vietnam, electric guitars are often used as an instrument in cải lương music (traditional southern Vietnamese folk opera), sometimes as a substitute for certain traditional stringed instruments like the Đàn nguyệt (two-stringed lute) when they are not available. Electric guitars used in cải lương are played in finger vibrato (string bending), with no amplifiers or sound effects.
Browse guitar sheet music for all levels of guitar players. Whether you're a beginner starting from a clean slate or a guitar shredder gigging on a nightly basis, our guitar sheet music collection has everything you need. Find thousands of guitar method and guitar etude books as well as your favorite guitar songbooks from Jimi Hendrix, Stevie Ray Vaughan, Metallica, The Beatles and more. Looking for digital guitar music, guitar chord books, guitar play alongs and guitar transcriptions? No problem. Take a load off, put up your feet and browse and buy guitar sheet music today.
Mahogany is a very dense, strong wood used in all parts of guitar manufacture except fretboards and bridges, which require harder wood. A mahogany neck and back are often found on short-scale guitars with maple tops. Another common combination is an all-mahogany body and neck (excluding the fretboard). Because mahogany is not very hard, it emphasizes the midrange and bass frequencies for a mellower guitar tone. Mahogany is a very resonant wood which enhances a guitar's sustain. It is generally a uniform rich brown color.
The descriptions that follow are very broad, but if you look around the guitar world you can usually pin any solid-body guitar down to one of these general categories. Of course you’ll see wild shapes like the Gibson Flying V, Ibanez Destroyer, Dean ML and Jackson Rhoads. They may look like they’re from another planet, but if you check their specs you’ll see they follow the same basic design principles as any other solid-body electric guitar.
Gibson market the J-200 as the most powerful acoustic guitar on the planet, and we might just agree. It’s so punchy, and has so much presence, both in the low end and right up there with the more sparkling high notes. Combine this with the L.R. Baggs Anthem pickup system, and this is a guitar that is aimed squarely at live performances where the acoustic needs to really make itself heard. It’l
Nylon strings are the standard for classical guitarists in today’s market.  While there are many types of nylon strings, the most commonly seen is clear nylon.  They are visually appealing while providing a clarity of tone with a bright attack that offsets the mellow overall tone of the classical guitar.  Other options include black nylon, rectified nylon, and composite strings.  The best classical guitars on the market come strung with nylons by default still.
Description: Guitar Type: Bass - Body: Maple & Mahogany - Figured - Body Construction: Solid - Top Wood: Cocobolo (Nicaraguan Rosewood) - Neck Wood: Maple - Neck Construction: 3 Piece - Fingerboard: Ebony - Frets: 24 - Inlay: White Dot - # of Strings: 4 - Headstock: 2+2 - Bridge: Adjustable - Bridge Construction: Carbon Fiber (Graphite) - Cutaway: Single - Hardware: Gold, 1x Volume Control - Pickup Configuration: Dual - String Instrument Finish: Oil
ACT TRMOLO ERSETZEN DER SAITEN Das ACT Tremolo erlaubt zwei Arten der Saiteninstallation. 1) Die Saiten werden durch Einsetzen des Kugelendes in den Saitenschlitz und Einhaken des Kugelendes unter dem Saitenfänger an der Rückseite der Tremolo-Einheit angebracht. 2) Die Saiten werden durch Einsetzen des Kugelendes in den Saitenschlitz und Einhaken des Kugelendes unter dem Saitenfänger an der Unterseite der Tremolo-Einheit angebracht.
Rickenbacker has produced a number of uniquely designed and distinctively trimmed acoustic guitars. Although a small number of Rickenbacker acoustics were sold in the 1950s and were seen in the hands of stars like Ricky Nelson[9]and Sam Cooke,[10] the company concentrated on their electric guitar and western steel guitar business from the early 1960s onward. From about 1959 through 1994, very few Rickenbacker acoustic guitars were made.
The key elements of mic positioning are distance from the source and orientation to it. Moving the mic closer to the amp provides more definition, increased highs and lows, and less room sound. As you pull the mic back, the sound becomes less detailed, more "midrangey," and more blended with the ambience. Depending on the room you're in, a distant-miked amp may gain a natural presence and unique character in the mix, despite an apparent decrease in definition. On the other hand, placing the mic too far back will result in a washed-out, murky, or hard-to-control tone.
Other Archtone owners may notice a slightly different model number, but with the exception of a tenor version, the only difference is the finish. The H1213 (your model) was finished with a shaded-brown sunburst, the H1214 was ivory-colored with a flame effect, and the H1215 was a sunburst with a grained effect. In excellent condition, this model is worth between $200 and $250 today. But in the average condition yours appears to be, it’s worth between $100 and $150.
InstantDrummer provides tempo-sycronized drum loop sessions that can be accessed easily from within RiffWorks guitar recording software. Most RiffWorks InstantDrummer Sessions are loop recordings of professional drummers brought into the InstantDrummer format for easy manipulation by RiffWorks users. Play along with InstantDrummer sessions by famous drummers like Alan White (Yes, Lennon), Jason McGerr (Death Cab for Cutie), John Tempesta (Rob Zombie, Exodus, Testament, Tony Iommi, The Cult), Lonnie Wilson (Brooks and Dunn, Faith Hill, Tim McGraw), and Matt Sorum (Guns N Roses, Velvet Revolver). Use them in your recordings royalty free!
While hollow guitars are best suited to jazz, there have been a handful of cases where rock musicians have utilized fully hollow jazz box guitars in rock and roll. Chief among these would be Ted Nugent, who actually used the excess feedback produced by his Gibson Byrdland as a musical tool. Hollow ES-335 style guitars are used in blues and rock more frequently than the jazz box (the Beatles used the Epiphone Casino extensively), though because of the feedback they produce most musicians stick with semi-hollow instruments.
A way to increase the usability of the sound acquired this way is to wire a capacitor in series with the pickup that has its electric polarity reversed. This filters out that pickup's lower frequencies and thus preserves the corresponding frequencies from the other pickup. The resulting sound is fuller and stronger, yet still different from the standard in-phase combinations, resembling the sound of a "cocked wah" (a wah-wah pedal set in a fixed position). The capacitor used for this is usually in the 20–100 nF range.[23]
In the late 50s, McCarty knew that Gibson was seen as a traditional company and began an effort to create more modern guitars. In 1961 the body design of the Les Paul was changed due to the demand for a double-cutaway body design.[17] The new body design then became known as the SG (for "solid guitar"), due to disapproval from Les Paul himself. The Les Paul returned to the Gibson catalog in 1968.

Next models is another semi-hollow design, only this time we are looking at a bit more neutral guitar. I wouldn’t go so far as to say that it’s somewhere between a solid body and a semi-hollow. That would simply be wrong, but it does have a harder tone for a model of this type. It didn’t take me long to find the right setup, and off we went. Sound, playability – everything is on point.
On round hole martin guitars, the serial and model numbers are stamped on the neck block inside the instrument. The number can be seen by looking inside the sound hole. Look at an angle towards the neck. All f-hole Martin archtops have their serial and model numbers stamped on the inside center of the backstripe, roughly under the shadow of the bridge (and best seen from the bass side "f" hole).
Unlike Christian, however, Montgomery used his thumb instead of a pick to create the percussive-yet-warm tone associated with his style. (According to interviews, Wes learned to play with his thumb because it created a softer sound, appeasing his neighbors.) With his phenomenal ear, Wes quickly grew beyond his influences and developed a style all his own. His knack for melody, groundbreaking use of octaves in a soloing context and intricate chord solos—as demonstrated in his devastating interpretations of standards like “Round Midnight” and “Days of Wine and Roses”—broadened the range of guitar, pushing the instrument into unchartered territory.
Over the years, the Gibson Memphis factory has become synonymous with creating some of the most accurate recreations of timeless classics. From the ES-335, ES-345 and ES-355 to the compact magic of the ES-339, the Gibson Memphis factory has built legendary instruments that pay tribute to the vintage masterpieces of yesteryear. To up the ante, the Gibson Memphis factory is now offering Limited Edition runs, showcasing the creative talents of their phenomenal crew, while boldly moving forward into a bright future.
All the connections are conveniently grouped together on the back of the unit. You have a mono 1/4” input for your guitar and a stereo output which allows you to listen to your playing on headphones, speakers, or a guitar amp (there’s also a balanced XLR output if you need it). Zoom also includes a USB connection, which not only can power this pedal via USB, but also turns the Zoom G3X into an audio interface! This way you can easily record in your favorite DAW. The USB connection also means you can use Zoom's free Edit & Share software so you can easily manage your patches on your computer. Just like everything else on the Zoom G3X, the input and output options are just right and provide plenty of flexibility. There’s really no major omission we can think of.
{"id": "113206695", "categoryId":"site5AAH", "name":"Vintage Vintage 1960s Maxitone Bruno Sunburst Hollow Body Electric Guitar", "pageUrl":"/Used/In-Store-Vintage/Vintage-Vintage-1960s-Maxitone-Bruno-Sunburst-Hollow-Body-Electric-Guitar.gc", "thumbnailUrl":"https://media.guitarcenter.com/is/image/MMGS7/Vintage-1960s-Maxitone-Bruno-Sunburst-Hollow-Body-Electric-Guitar/000000113206695-00-180x180.jpg", "hasFeatures":"0", "isAccessory":"0", "message":"", "value":"299.99", "priceMin":"299.99", "priceMax":"299.99", "msrp":"", "productVisibilityMSRP":"1", "restockPrice":"", "openBoxPrice":"", "clearancePrice":"", "isPlatinum":"0", "priceSavingsMaxPrice":"100.00", "priceSavingsMaxPercent":"10,000", "inventory":"1", "brand":"In Store Vintage", "reviewStarImageUrl": "https://static.guitarcenter.com/img/brand/gc/cmn/Sprit-Sm-Stars.png", "reviewStarRating":"0.0", "reviewStarRatingInteger":"0", "reviewHowManyReviews":"0", "usedOrNew":"used", "discontinued":"0", "onOrder":"0", "clearance":"0", "canBeSold":"1", "accessoryCategories":"site5LAAA,site5LFMIC,site5HBA", "stickerText": "Price Drop", "isVintage": "1", "outletonly": "", "checksum":"83818118023", "priceVisibility": "", "itemType": "Vintage"}

Our basic no frills guitar Denny designed to go head to head with $1000+ guitars. Magazine reviews and customer testimonials say it actually outperforms many well known $1500 models. If you want the look, feel and sound of a high dollar acoustic with 50% easier playability this is the best guitar we offer. Shipped wholesale direct from our workshop in Lincoln, Nebraska. 100% money back guarantee, lifetime warranty.
The best acoustic guitar brands in India are available for beginners to buy. When buying a guitar at a beginner level, it is good to go with the acoustic guitar. This is the type of guitar that is easy to learn and play. The strings are available in various materials. The make, shape, style, and material used in the strings are the features to look at when you buy a guitar. Acoustic, Electric, Spanish Guitar, Steel, Bass, and Resonator guitars are available in India. You can also find twelve string guitars to buy at a few locations in India. You will find amongst this list, best guitar brands in India for beginners as well as advanced learners.
Laminate guitars are not made with solid pieces of wood. Instead, a laminate guitar is made with layered pieces of wood, like a veneer, to create the body of the guitar. Despite its reputation among music snobs, laminate guitars can be top-selling, high-performing instruments. Just check out the Fender CD-60CE Acoustic Electric Guitar for proof of a beautiful, all-laminate, highly-popular instrument!
Compressor sometimes sounds good after distortion too, it helps with noise (compressors can be noisy and if put before overdrive then the distortion pedal makes the noise louder). Placing the compressor after distortion also increases your sustain (depending on the type and amount of distortion used!). It can sound darker if placed after as well - so it really is down to your ears and what you think sounds best! But I have mine first in the chain, before Fuzz as I don't often (ever?) use them together

The Fuzz-Tone connection hints that we need to look further back, and across the pond, for earlier examples of recorded guitar distortion. Gibson, and hence Maestro, was given the circuit that became the Fuzz-Tone by studio engineer Glen Snotty. Snotty, in turn, had devised the transistorized fuzz-generating design to replicate the sound that occurred when a tube preamp in the channel of a mixer he was using to record Grady Martin’s short-scale bass solo for the 1961 Mary Robbins hit record ‘Don’t Worry’ started to fail and yield a distorted tone. Whoever decided to stick with the track rather than re-record it through a properly functional channel was on to something; the result was Nashville’s first recorded fuzz guitar (a Danelectro bass, in fact). Courtesy of Maestro, Snotty’s fuzz circuit soon made the trendy new sound available to the world.
{ "name": "Ebony", "skuUrl":"/guitars/epiphone-les-paul-special-vintage-edition-electric-guitar/j40301000002000", "status": "instock", "statusText": "In stock", "pimStatus": "R1", "inventoryText": "In Stock & Ready To Ship", "inventoryKey": "in_stock", "price": 149.00, "formatedIntegerValue": "149", "decimalValue": "00", "isOnSale": false, "easyPayOptions":"0,0,7500007,12 Months Promotional Financing,10/28/2018,Special 12-month financing. Valid through,149.0,true,/pages/Gear-Card-Rewards.gc", "msrp": 248.00, "salePrice": 149.00, "listPrice": 149.00, "isPriceDrop": false, "priceDropPrice": "", "savingPercent": "0.00", "promos":["freeShipping","topRated","guarantee","international"], "warranty": true, "freeWarrantyAvail": true, "sku": "site1skuJ40301000002000", "displaySku": "J40301 000002000", "serialized": false, "shipsFree":true, "condition": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/J40301000002000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"false", "invMsgPreOrder":"false", "invMsgPromiseDate":"", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.musiciansfriend.com/is/image/MMGS7/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Ebony/J40301000002000-00-140x140.jpg", "styleImgAlt": "Les Paul Special Vintage Edition Electric Guitar Ebony", "freeGiftWarning":false, "freeGiftWarningTips":"", "isShipsInternational": true, "pdpLoyaltyPoints":"1,192", "pdpLoyaltyPointsMultiplier":"1.0", "checksum":"93895071200", "restrictionType":"", "restrictionError":"" }
Music Go Round® is a registered trademark of Winmark Corporation based in Minneapolis, MN. Each franchise is independently owned and operated. Other brand names are trademarked or registered by their respective companies. The trademarks and logos used in this website are owned by Winmark Corporation® and any unauthorized use of these trademarks by others is subject to action under federal and state trademark laws.
The remaining ’62 Teisco laps had a sort of paddle shape to the body, with sides wider than the fingerboard all the way up to the asymmetrical head with the circle Swan logo. The EG-A and EG-S had short scales and black fingerboards with the diamond markers, while the EG-U and EG-L had longer scales with fingerboards angled toward the bass side at the pickup. The EG-U had a light fingerboard with split-parallelogram markers, whereas the EG-L had a dark ‘board with dots. All were six-strings with one black-covered pickup and a little plate with volume and tone controls. Tuners mounted from behind the head as on a Spanish guitar.
Jack Douglas also points out a beneficial side-effect, in his experience, of recordings made using the phase EQ approach: "When you build a mix — I don't care if it's four tracks, eight tracks, or 96 — the real nightmare is when you put something up and the only way you can hear it is by blasting it. There's nothing worse than putting up something you're excited about, and it's gone. If you [record guitars] like this, I guarantee that as soon as you put the sound in the mix it will be there. Not only that, it won't wipe out everything else in the mix, because it will have such a separate and distinct character."
There are, by the way, a number of discrepancies between Japanese Teisco and American Teisco Del Rey literature from 1966. Many of the older models continued to be promoted in Japan, but not in the U.S. Virtually all guitars in U.S. literature are also seen in Japanese catalogs. This does not mean that just because W.M.I. did not promote certain models, they were not still available in America. Many may have gone to Sears as Silvertones, and it’s possible that W.M.I. still brought in guitars other than those in its catalog.

Many guitars (even new guitars) need the frets leveled in order to play buzz-free with low action. Most electric guitars with bolt-on necks come from the factory with high tongue frets. Doing great fret work is a learned art, and I guarantee that you will be happy with mine. All my fret work jobs are performed with the guitar mounted in a neck jig that simulates string tension. This allows very accurate work. Re-fret jobs include leveling the fretboard if needed.
Top 4 in my opinion. Countless guitarists have played them on some of the best albums ever written. I've owned numerous vintage guilds and still own a vintage f50 and d55. Recently Fender bought guild and I bought a new d55 which was a bit over rated and over priced in my opinion. But Fender has sold Guild and I sold my fender owned guild d55 only to buy a brand new by the new owners who moved Guild to a California facility and I must say it holds its own with the vintages I have. Guild is back! A great name in acoustic guitars. A great build (thank God once again), and the quality has always been with the best. Long live guild and it's a top 4 brand just behind Martin, Taylor and Gibson.
The Japanese copy juggernaut got off to a fast start, and the second major Univox guitar was the Lucy, a lucite copy of the Ampeg Dan Armstrong, again produced by Arai, introduced in 1970. This guitar had a surprisingly thin bolt-on neck (especially compared to the Ampeg original) and a slightly smaller body. The fingerboard was rosewood with 24 frets and dot inlays. This had a fake rosewood masonite pickguard with volume, tone and three-way select. Like the Ampeg, the Lucy had a Danelectro-style bridge/tailpiece with little rosewood saddle. Unlike the Ampeg – which had Armstrong’s groovy slide-in epoxy-potted pickups – this version had a pair of the chrome/black insert pickups jammed together at the bridge. Other Japanese manufacturers also made copies of the Ampeg lucite guitar, notably carrying the Electra (St. Louis Music) and Ibanez (Elger/Hoshino) brand names, with versions of the slide-in pickups. In ’71, the Univox Lucy (UHS-1) was $275 including case. Just how long the Lucy remained available is unknown, but it probably did not outlive the original and was gone by ’73 or ’74.
So half of it is finding a happy place in terms of neck size. The other half is the setup. String height is usually adjustable, with electric guitars, which is a good thing in your case. Lower string height means you don't need to push down on the string as hard to play the notes. When you find a guitar that feels good to you but the strings are kinda hard to push down, talk to the store about having it setup and intonated with a very low string height... some people use the term "fast" action.
Compared with many of the guitar models on this list that have been around for half a century, the Ibanez Artcore AF75 is still a baby. Ibanez introduced its Artcore line of semi and full hollow body electric guitars only in 2002. Nevertheless, the Artcore guitars have amassed a massive fan base because of their tuning stability, rich tone, impressive sustain and overall quality. Plus, they’re also extremely affordable considering their features.

It was shortly after the debut of the first Supros that National Dobro entered a period of major transition. By 1935, at least, the company had decided to abandon the sunny beaches of L.A. for the freezing winters of Chicago, then the principal home of America’s instrument makers, and not coincidentally, America’s giant mass merchandisers Montgomery Ward and Sears. Both Wards and Sears had been offering National and Dobro resonator guitars since the late ’20s. Being in Chicago had the obvious advantages of proximity to the resources surrounding the business and being next door to the world’s two largest retailers of the day. The move to the Midwest began early 1936 and took almost a year and a half. Throughout most of ’36, the majority of production continued in L.A.

The Yamaha Pacifica has long proved a benchmark for quality and specification, and the 112V remains one of the best electric guitars for beginners. The 112 is far from fancy and simply concentrates on the bare necessities. Yet the construction is of excellent quality. Trust us, if looked after this will be a guitar for life. By design it's an altogether more modern, brighter and lighter take on a hot-rod Strat. But when we say brighter that doesn't mean overly shrill. In fact the bridge humbucker will surprise some, it's beefy without being too mid-range heavy and although the coil-split proves a little bland played clean, with a distortion boost it's a pretty useful gnarly and wiry rhythm voice. It's good to have the choice too when mixed with the middle pickup - switching between the full and split coil here is subtle but, especially with cleaner 'class A' amp voicings, there's enough character difference to be useable. The solo single-coils impress - plenty of percussion and with a little mid-range beef added from the amp these get you to the correct Texas toneland. Neck and middle combined produces a fine modern Strat-like mix - the added brightness will cut through a multi-FX patch nicely.


700-Series, which are all solid-bodies are probably worth $250-$350, maybe a little more for the 4-pickup 742 model. I’m pretty sure that they were on the market at the same time as the 800s but not as many are being seen. Since the 800s were a step-up in quality compared to previous Kents and the 700s used similar design features, they should be pretty decent instruments. Although collectors haven't shown a lot of interest in them, rarity has to be considered an influence on the price at this point.Recently a 742 sold on Ebay for over $1000 and a 740 recently sold for $999. Previously most of the 700s had been selling for $200-400.
If you want to spring for a pedalboard and processor combo that offers multiple effects in one unit, you might want to check out something like the HeadRush Pedalboard with Guitar Amplifier and Effects Modeling Processor. It offers 33 amplifier models, 15 cabinet models, 10 microphone models, 42 effects, and includes an expression pedal, 7" touchscreen, 12 foot switches with OLED Screens, and more.
Single coil pickups utilize a single magnet. They also typically have a lower output than humbucking pickups, which means they aren’t capable of producing as much distortion as a humbucker equipped guitar. However, because they’re not intended to be used with extreme levels of distortion they have a very rich and musical voice when played with lower amounts of gain.
: This vintage YAMAHA is one of the greats folks and here for your serious consideration today at Joe's Vintage Guitars.... This is the Classic Vintage Yamaha FG-200 - Nippon Gakki body seems the same specs as the famous FG180...hummm? interesting She's been lovingly played for nearly 40 years,its beautifully aged now with a great feel & patina only found on real vintage guitars of this age and caliber. This guitar really has nicely opened up over the past 40 years and you just don't get booming bassy tone like this one with a new guitar thats for sure. This example is not mint but is beautiful in its own right, it does have a few nicks, dings and wear but nothing really bad at all really she just looks the part of the 40 year old Martin D28 vintage guitsr. A lot of guitar for not a lot of cash... Vintage aint goin down..get her at a great price today! Let me know...thanks for your interest, Joe email me: gr8bids@comcast.net This is an early one from the Nippon Gakki plant and has a surprising boom even for or a 200 same as our great old red lable FG180 for that matter with no real decernable diference. I cannot find a serial number but is believed to be late 60's - early 70's This old girl has Excellent low end sound!!! and tone on this guitar is wonderful - it really booms! Condition: Average vintage wear wich includes minor pick wear, scratches dents & dings for an old vintageguitar. but no cracks to be found, straight neck, trussrod is functioning properly, very good frets still playing well all the way up & down the fingerboard with no funny buzzes or dead spots... Frets 1 - 5 ( cowboy cord area )have medium play wear but still plenty of life remaining no problemo. action is very good at 3/32 1st E string @ 12th fret. Tuners are the original and in excellent working order. Bridge plate is securely fastened to top. We have just as a precationary installed A PlateMate brass plate has now been installed to any prevent further wear to bridge plate which is common among these vintage guitars. This brass plate has also contributed to its big booming tone now is even a more rich sounding competitor to a vintage Martin D-28... FRESH SET UP...with Martin Bone & Saddle... this guitar is a wonderfull fun guitar to play lots of bang for the buck factor here.. This guitar is overall a very solid well built guitar that is standing the test of time it also is a great sounding vintage guitar that plays very nicely. Ya can't go wrong with this wonderful vintage Yamaha FG Nippon Gakki guitar Has a new bone saddle and Martin Silk Steel strings. No case included but will protect and properly package for shipping. PlateMate product works very well and is easily removed if desired. To my ear it enhanced this boom-box's sound quality and is described by the manufacturer as follows: If you want to protect and enhance the sound and tones and balance out string volume of your acoustic guitar, Mitchels Plate Mate is the way to go. Mitchels Plate Mate is a small piece of brass that is applied without using or altering of tools, and is installed as fast as you can change a set of strings. This was invented and patend mainly to prevent damage caused by ball-end strings on the acoustic guitars bridge plate, it is also proven to enhance volume, tones, and balances out string volume by one of the best acoustic guitar makers in the world. Mitchels Plate Mate will protect your guitar from ball-end strings pulling up threw the bridge plate and possibly cracking the bridge or pulling the bridge off the top of your guitar which would be a very expensive repair bill. It also protects your bridge pins, and saddle by making the string windings stay down in the string holes where they belong. I have used Mitchels Plate Mate in guitars priced from $100 to $50,000 it doesnt matter the price just protect your prized posetion or investment. .
The Fender Bassbreaker 15 Amplifier Head presents a budget friendly option for those in need of great tone. You have 15 watts of pure power to channel here as well as a studio friendly Power Amp Mute so you can record straight into a desk - a great feature for those in need of a powerful stage and studio amplifier. This is a professional grade amplifier head that features 3 very unique tonal options and overdrive levels to provide you with a whole host of lush fender tones that range from glass like cleans to vintage overdrive. Perfectly paired with the Fender Bassbreaker 212 Guitar Cab.

An alternative solution to raising the tailpiece is to pass the strings through from the FRONT of the tailpiece (heading towards the back of the guitar) and then passing them over the top of the tailpiece before they go over the bridge. Here you can see evidence of someone having set up the guitar in this way in the past (scuff marks from the strings passing over the top). Personally, this is not something I’ve ever needed to do, but the option is there should you choose to take it.
Ibanez are a Japanese musical instrument company. Although Yamaha is a better known Japanese musical instrument company, Ibanez exceeds expectations for electric guitars. This brand of guitars stands out in the world of rock guitars. They gained popularity in the 1980s when they introduced their original designs for guitars based on Steve Vai’s JEM Universal. Their designs have since become some of the biggest selling metal guitars. The Ibanez guitars are used by guitarists such as Steve Vai, Paul Gilbert, and Joe Satriani. In addition, Ibanez guitars tend to be very affordable, giving you a great guitar for a cheaper price.
Many compressor pedals are often also marketed as "sustainer pedals". As a note is sustained, it loses energy and volume due to diminishing vibration in the string. The compressor pedal boosts its electrical signal to the specified dynamic range, slightly prolonging the duration of the note.[92] This, combined with heavy distortion and the close proximity of the guitar and the speaker cabinet, can lead to infinite sustain at higher volumes.
Run a length of wire (approx two feet is usually plenty) through the jack mounting hole and down into the cavity. When you see the wire in the cavity pull it up through the F hole. Make sure the wire is long enough for one end to stick out the jack hole, and the other to stick out the F hole. Tape the jack hole end of the wire to the guitar with masking tape, or tie it to the strap button. This will ensure it doesn’t fall through the jack hole while you’re working on the other end.
​​Our primary goal here at Top Custom Guitars is to create unique instruments that match our players' personalities. The bond we've formed over the past 15 years with each of our clients has not only fueled the growth and maturity of our instruments, it's fueled our creative growth as a company. YOUR passion drives OUR passion, and because of the individual relationships we build with our clients. Enjoy our galleries and forums, and if you have any questions, ideas, or dreams to share, we’d love to hear them.
Search through such iconic pieces of gear as pre-war Martin acoustics, ’50s-era Gibson electrics and ’60s Fender® Super Reverb amps—or perhaps you've always wanted to play an amplifier that your favorite British Invasion or psychedelic garage band used, in which case, you'll have the pleasure of browsing countless vintage amplifiers from Vox, Danelectro, Silvertone and more. Our Vintage Collection also consists of a wide range of MIDI and pro audio equipment, with everything from dynamic and condenser microphones to signal processors and stunning keyboards made by Moog, Univox and Hohner.
Note that much of information and pictures are courtesy of Paul Bechtoldt and D. Tulloch's book, Guitars From Neptune", 1995. Much of this book is catalog reprints, but from it and American Guitars by T. Wheeler, I was able to construct this information. Personally I've never really actively looked for these guitars, so my knowledge base is somewhat limited. But a lot of people buy these at garage sales, flea markets, etc, and ask me about them. There doesn't seem to be a lot of information out there. This is probably because Danelectros and Silvertones are considered "low end" vintage guitars at best, and don't sell for a lot of money. So I hope this page will be of some help in their identification.
These guys are great! I took my Martin in for a refret, and it might have been the cleanest I have ever seen it done. Played better than it did when I got it. So after that show of quality work I took... my old Guild to them. It had developed a little belly bulge and warped top. Mark got that thing sounding and playing like brand new. They are priced honest and fair, and do work in a very timely manner. I am done looking for my guitar shop. I highly recommend these gentlemen. See More
Guitar effects pedals alter the pitch, tone, and sound of your electric guitar or bass guitar, and as such, it is important to ensure you are armed with as much knowledge about them as possible before making a selection. The alterations made by these effects pedals include acoustic effects, compression, delay, reverb, distortion, overdrive, equalization, loopers, samplers, noise gates, pitch, octave, modulation effects, wah, multi effectors, volume, expression, and filters. They are available from brands such as Boss, MXR, TC Electronic, Electro-Harmonix, Catalinbread, and Fulltone.
We are proud to offer this very Rare and beautiful and highly collectible vintage 1983 Alvarez Electric/Acoustic 5078 with a les Paul style body shape. Top of the line workmanship fit & finish work here Crafted in Japan this is the limited special production Anniversary model made in 1983. This truly fine rare example comes with its nice original Alvarez black exterior tolex with the blue Martin style plush lined hard shell case. Did we say SUPER RARE....WoW!...we were completely amazed at the fact that this ( Les Paul style baby sounds so great plugged in or unplugged just beautiful. This one has a rich full bodied sound as an acoustic which is hard to find with this thin Les Paul shaped body makes it very comfortable to play long duration and not to mention did we say BEAUTIFUL as well as a real unique player...see the Headstock shape in the pictures this is truly a real beauty. This one is sure to please the Vintage Alvarez Acoustic lover... I'm a vitage Alvarez believer & after you see and play and hear this so will you. Condition for a 26 year old vintage guitar this thing is darn near mint with just a few tiny minute dings, see the detailed high res pictures for all the cosmetics, JVG RATED at 9.2 out of 10 ....... any questions? please email us @ gr8bids@comcast.net Thanks for your interest! .

Ostentatious Delays: If you're making very rhythmic music of any kind, it makes sense to use tempo-sync'd delays, to avoid undermining the main pulse. However, simple tempo-sync'ed delays tend to be masked by the main rhythmic stresses, so they sink into the background of the mix unless mixed very high in level, which makes it difficult to create ostentatious delay effects in rhythmic music without swamping your mix. One solution to this problem, very common in trance music, is to set a delay to a three-16th-note duration, which means that although the delay repeats never step outside the 16th-note grid, they'll often miss the main beats and therefore remain clearly audible. Mike Senior

However much you swap your guitar’s pickups, strings, and wiring configuration, tweak your amp, or revamp your pedalboard, you will never achieve the golden tone that rings in your head if you don’t take one tip to heart: it all starts with the wood. Sure, these are electric guitars, and all the electronic components in the sound chain will affect what comes out of the speaker, but they are acoustic machines first and foremost. Hit the strings with your guitar unplugged, and it still rings and resonates, and the sound you hear—even with no electronic devices attached—still defines the core of your tone. And to make sure this is the right tone for you, or to avoid fighting a tone with endless component tweaks that never seem to satisfy, you need to understand a little bit about how all that wood sounds.
Coming from Martin's Travel Series, the LX1E Little Martin has smaller proportions, with a total length of 34", body width of 12", shorter scale length of 23" and 1 11/16" nut width. While it can be a bit too small for some, it is easy to appreciate its impressive workmanship, bearing the same build quality and materials as found on their more expensive models. With the LX1E, you can own an affordable Martin guitar that has been proven to be a true workhorse instrument.
Most Gibson guitars feature two humbucking pickups, giving them a very full, clean sound. They are very simple in design, and easy to use with a focus on quality. Maintenance is also easy with Gibsons. Their bridge style places the strings closer together than the likes of Fender or Ibanez guitars, making them slightly different to play. While there is slightly less room for error in finger placement, the strings’ proximity makes them a better fit for small hands and for instrumentalists who need to rapidly navigate the fretboard.

So you want to learn how to play guitar but don’t know where to start? No worries. This how to play guitar for beginners guide will cover all the basic requirements to get you started with playing guitar. The guide is split into 2 sections: The Basics – where you’ll learn about the various parts of the guitar, how to hold the guitar and how to tune your guitar. Playing – where you’ll learn popular chords, strumming techniques, and how to read guitar tabs. This guitar for beginners guide is meant for guitarists just starting out, however there are also tips and
Another great practice amp in the running for best electric guitar amp for beginners is the Blackstar HT Series HT-1. It’s a 1W tube amp with a single 8″ speaker. It features 2 channels (clean and overdrive), stereo MP3 / line input and external speaker output. It’s use of dual-triode ECC82 tubes provides the crunch and break-up characteristics of a traditional 100w amp at a much lower volume. It also has EQ, Gain and Reverb settings.
“Take a humbucker wound with 42-gauge wire as a benchmark. With an Alnico II magnet, it would have a warm, soft bass response, a very sweet high end and a slightly pronounced mid- range. Alnico III, funnily enough, is not quite as strong as Alnico II. So, the highs tend to be more muted and rounded. Probably the best way to imagine the sound of Alnico III is to think of the early 1950s when this form of magnet was very common. Think of the sounds of the jazz and clean guitar tones from that time – that plummy roundness.
Hello. If any of you who have a dorado guitar would like to sell it, please email me (swiver84@hotmail.com). I am always looking for cool vintage guitars. I am a big fan of the Gretsch name and have found the Dorados to be very nice guitars. I don't check follow ups much, so you'll have to email to get in touch with me. Put "Dorado" in the subject because I get a lot of spam and tend to get crazy with the delete button. Thanks :)
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: left handed electric guitars","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","prop17":"sort by","evar51":"default: united states","prop5":"[gc] shop: guitars: electric guitars: left handed electric guitars","prop6":"[gc] shop: guitars: electric guitars: left handed electric guitars","prop3":"[gc] shop: guitars: electric guitars: left handed electric guitars","prop4":"[gc] shop: guitars: electric guitars: left handed electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category2"}

In the second diagram, the two pickups are wired in series. The theory behind series wiring is that the ground wire of one pickup is connected to the hot wire of the other pickup. As a result, they become a kind of compound pickup, with one ground and one hot for both. When wired in series, the pickups combine their impedance (resistance) and the output is very high. If your Strat’s middle pickup is a reverse-wound/ reverse-polarity type (aka RWRP), you’ll get the same humbucking effect as you do when the pickups are wired in parallel—no changes there.
Many modern processors have such great presets you'll never need to get delve any further to create your own. However, almost all units with presets allow you to easily create your own favorite presets. You can start with a factory preset, tweak the sounds to your taste, then save it in your own location to be recalled at the touch of a button while you're playing.

This is a no brainer, but a value that must be considered before any purchase no less. As mentioned above, your abilities on the instrument will likely affect the price range you’re looking at, which may have an effect on the brands you shop within as a consequence. For instance, if you’re not looking to buy a high end guitar, you probably won’t even bother testing out a Gibson, as their guitars will likely be out of your range. The reverse is true as well, an experienced player on the market for high end tone probably won’t be satisfied by many of Yamaha’s offerings.


For most players, the ideal location to place modulation effects—which include phase shifters, flangers, chorus, rotary, tremolo, vibrato and so on—is directly after a compressor and/or overdrive/distortion pedal. When these effects are distorted after the fact, the sound tends to smear and lose definition (particularly with chorus), although there are a few exceptions where distorting a flanger or phase shifter can sound really cool. The best example is Eddie Van Halen, who doesn’t use distortion pedals and instead generates all of his distortion from the amp. When a flanger or phase shifter is placed in front of a distorted amp or overdrive pedal, it can create dramatic thick, jet-like phasing and flanging effects (See Example 2, below).
Featuring classic Fender design, smooth playability, and simple controls, the Squier Classic Vibe Telecaster '50s is a great first electric guitar. The fixed bridge and quality tuning machines ensure simple and reliable tuning stability—a potential frustration for new players trying to learn on poor quality guitars. Single volume and tone controls along with two bright-sounding single-coil pickups give the beginning player a wide range of tones that are easy to control. The Telecaster has been a mainstay in music for decades and is especially associated with great country, pop, surf and rock sounds.
The short-lived Elite Telecaster of 1983 incorporated two specially designed humbucking pickups powered by an active circuitry that featured a “TBX” guitar expander and an MDX midrange booster with 12 dB of gain. Other features included a “Freeflyte” hardtail bridge and die-cast tuning machines with pearloid buttons. This guitar was among the latest CBS-era Fenders to feature a BiFlex truss-rod system, low-friction EasyGlider string trees and active electronics. After CBS sold Fender to a group of employees led by Bill C. Schultz in 1985, production ceased on the Elite Telecaster and other Elite models. Fender Japan made its own version of the Elite Telecaster in late 1984, which featured a 22-fret neck with medium-jumbo fretwire and a modern 9.5 inch fingerboard radius. Notable Elite Telecaster players include Johnny Hallyday and Dave Davies of The Kinks. Michael Houser w/ Widespread Panic and Andy Summers of The Police.
The history of Electric Guitars is summarized by Guitar World magazine, and the earliest electric guitar on their top 10 list is the Ro-Pat-In Electro A-25 "Frying Pan" (1932) described as 'The first-fully functioning solid-body electric guitar to be manufactured and sold'.[31] The most recent electric guitar on this list is the Ibanez Jem (1987) which featured '24 frets', 'an impossibly thin neck' and was 'designed to be the ultimate shredder machine'. Numerous other important electric guitars are on the list including Gibson ES-150 (1936), Fender Telecaster (1951), Gibson Les Paul (1952), Gretsch 6128 Duo Jet (1953), Fender Stratocaster (1954), Rickenbacker 360/12 (1964), Van Halen Frankenstein (1975), Paul Reed Smith Custom (1985) many of these guitars were 'successors' to earlier designs.[31] Electric Guitar designs eventually became culturally important and visually iconic, with various model companies selling miniature model versions[32][33] of particularly famous electric guitars, for example the Gibson SG used by Angus Young from the group AC/DC.
Here we JUST SOLD OUT: another excellent FG160 for your serious consideration the Yamaha FG 160 Acoustic Guitar Made in the early - mid 70's from Taiwan factory. This example was built well over 35 years ago and was built to very high detailed standards as well as some of the best grained Mahogany woods seen in this time period ( see pics for those detail ) in that time period these were meant to compete with the great M@r#!n and now this Yamaha is quite well aged too and is a REAL vintage guitar in its own right sounding SWEET with its well aged woods with really beautiful patina of a true vintage instrument. This one has the Amber/Tan label and not the Red Label but the golden label. The frets are very good - original I did a quick dressing of the lower 5 or so frets and polished all. The guitar has it's natural age and character with beautiful patina and it has been played of course its not new its over 35 years old with a few insignificant minor nicks,dings from a well loved and adult respected instrument. This fine example is here and in stock... We upon receiving have remove the strings cleaned and detailed the guitar oil rosewood and polish finish, We have * upgraged* its TONE by installing a Martin BONE nut and compensated BONE saddle set for improved tone resonance over the old plastic stuff so she has a nice deep ring to its tone now and this guitar to plays very well Yamaha's and they are truly amazing instruments very well compared to a much more expensive brand guitar as you may have heard…. These FG’s are known for there fine construction and playability with amazing tone for this kind of money… to get a vintage aged tone woods instrument built this well and in this kind of condition make this FG160 the one to own for a song! Re: condition its over 35 years old and is BETTER than average This guitar has no cracks, no finish checking no warped top, no loose or pulling bridge Its neck has a real nice feel to it and is a medium - slim profile = feels like M@r#!n D-28ish substantial but not too fat - Just right! 1-11/16ths at the BONE NUT Play action is very good see pics Its a standard Dreadnought Acoustic and is Identical to the Yamaha FG180 This is an excellent vintage Yamaha FG160 You will be pleased with its sound she has good bones its over 35 years old and has proudly stood the test of time there is no reason this guitar will not continue to serve another 35+ years with average care. Beautiful Patina only seen on real vintage guitars Let me know if you have any questions ore are ready to purchase email Joe at JVGuitars@gmail.com.
Gretsch G5422G12 Electromatic Double Cutaway Electric Guitar, 12-String   New from$999.99In Stockor 12 payments of $83.34 Free Ground Shipping Reverend 2017 Airwave 12 Electric Guitar, 12-String   New from$1,199.00In Stockor 12 payments of $99.92 FREE 2-DAY SHIPPING D'Angelico Premier DC Electric Guitar, 12-String (with Gig Bag)   New from$899.99Only 2 Left!or 12 payments of $75 Free Ground Shipping Ibanez Artcore AS7312 Electric Guitar, 12-String   New from$499.99In Stockor 8 payments of $62.50 FREE 2-DAY SHIPPING See All Electric Guitars: 12-String

{"eVar4":"used: amplifiers and effects","eVar5":"used: amplifiers and effects: amplifiers","pageName":"[gc] used: amplifiers and effects: amplifiers","reportSuiteIds":"guitarcenterprod","eVar3":"used","prop18":"skucondition|0||creationdate|1","prop2":"[gc] used: amplifiers and effects: amplifiers","prop1":"[gc] used: amplifiers and effects","prop17":"sort by","evar51":"default: united states","prop10":"condition","prop11":"used","prop5":"[gc] used: amplifiers and effects: amplifiers","prop6":"[gc] used: amplifiers and effects: amplifiers","prop3":"[gc] used: amplifiers and effects: amplifiers","prop4":"[gc] used: amplifiers and effects: amplifiers","channel":"[gc] used","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] used"}
Acoustic guitar is the first choice of many guitar beginners. There are a lot of benefits to start with an acoustic guitar. First of first, acoustic guitars are cheaper than electric guitars. Then acoustic guitars are easy to carry, you don’t need electricity and amplifiers. The most important reason I think is a good acoustic guitar make amazing sound that different from electric guitars.
But add some effects to the blend and the results can be even more interesting. Keyboard-like tones can be generated by rolling off the tone pots and employing digital delay, expanding the sound of your band without overstuffing the van, and the gentle application of a phase shifter or wah-wah can bring an interesting voice to warm, low tones. Jimi Hendrix’s “Pali Gap” is a classic example of the latter.
Originally started as a replacement parts shop in Japan, ESP Guitars – which stands for Electric Sound Products – got their guitar manufacturing business off to a rocky start here in the United States. They were taken to court by Gibson guitars for producing instruments that too closely resembled the American brand’s guitars. But, they settled out of court in 1978 and ESP’s reputation eventually grew, thanks in part to George Lynch, the guitarist for the 80s metal band Dokken, and his signature axe pictured here – The Kamikaze Model 1. Now, ESP guitars are wildly popular amongst metal and hard rock clientele and you can hear their instruments on the records of some of the brand’s loyal artists – including the likes of James Hetfield and Kirk Hammett of Metallica, Page Hamilton of Helmet, and the guys in Children of Bodom.

After music fans heard his impressive blues rock playing on John Mayall’s ‘Beano’ album, they began to spray paint “Clapton is God” on London, England infrastructure. It’s safe to say that Clapton left quite an impression on people. His playing with Cream, Derek and the Dominos, and Blind Faith as well as in his solo work only helped to strengthen Clapton’s legend.


Over the years, the Gibson Memphis factory has become synonymous with creating some of the most accurate recreations of timeless classics. From the ES-335, ES-345 and ES-355 to the compact magic of the ES-339, the Gibson Memphis factory has built legendary instruments that pay tribute to the vintage masterpieces of yesteryear. To up the ante, the Gibson Memphis factory is now offering Limited Edition runs, showcasing the creative talents of their phenomenal crew, while boldly moving forward into a bright future.
{ "thumbImageID": "Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Sonic-Blue/H75903000002000", "defaultDisplayName": "Yamaha Billy Sheehan Signature Attitude 3 Electric Bass Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51308847077862", "price": "2,599.99", "regularPrice": "2,599.99", "msrpPrice": "4,600.00", "priceVisibility": "1", "skuUrl": "/Yamaha/Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Black-1308847077862.gc", "skuImageId": "Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Black/H75903000001000", "brandName": "Yamaha", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Black/H75903000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Sonic Blue", "sku": "sku:site51308847077871", "price": "2,599.99", "regularPrice": "2,599.99", "msrpPrice": "4,600.00", "priceVisibility": "1", "skuUrl": "/Yamaha/Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Sonic-Blue-1308847077871.gc", "skuImageId": "Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Sonic-Blue/H75903000002000", "brandName": "Yamaha", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Billy-Sheehan-Signature-Attitude-3-Electric-Bass-Guitar-Sonic-Blue/H75903000002000-00-60x60.jpg", "imgAlt": "" } ] }
Pete Townshend turned his guitar into a machine gun. That was the actual sound he went after, slamming his guitars into speaker cabinets and toggling the pickup-selector switch violently. “To me the guitar was a symbol,” explained the Who’s lead guitarist. “It was a metaphor for a machine gun. And the only thing you could do with a machine gun in the 60s was break it across your legs. That’s what I did.” You can hear these specific sonic strategies on songs like My Generation and Anyway, Anyhow, Anywhere.
Electric guitars are capable of producing a multitude of different sounds, ranging from the purest cleans right through to saturated distortion and feedback. Many factors influence the final recorded sound; the type of guitar and amp, and any stompbox or rack-mounted effects used will shape the initial tone. The choice of microphone(s) and mic’ing techniques, too, along with any studio processing, will also contribute to the end result. Your playing style is also crucial; experiment by playing with fingers or a variety of plectrum gauges until you get the right attack. While most guitarists play with a pick, coins can also be used to produce interesting harmonic overtones – just ask Brian May or Billy Gibbons.
Read Full Review Here is another superstrat design electric guitar on the list that is well recommended for a budding guitarist. While for veteran player’s out there who is on a hunt of buying an all around electric guitar on a minimum prescribe budget. The ESP LTD M-10 could be that affordable gem of a guitar you’ve been looking for and always wanted.
The 2nd basic beginner guitar chord you should learn is C, or C major. You don’t have to say “major” in the name of the chord. If you just say C chord it’s assumed that it’s a major chord. You only want to strum the top 5 strings (that means the highest sounding 5 strings, not their relationship to the floor) The X in the guitar chord chart means not to play that string, or to mute it.

Most of the time, you’ll almost always see a piezo pickup on an acoustic electric guitar with the addition of an on-board preamp. Typically, it will be installed underneath and in contact with the saddle on the bridge of the guitar where it can effectively pick up vibration energy. This specific type of device is called an active undersaddle transducer. This type of pickup is often paired with other pickups and microphones to provide versatility for sound options, and to produce a richer, more organic and natural sound. A piezo pickup and other types of electronic pickups are what we call active pickups.
Players discovered that, if you put the switch in the right position, you could get the neck-and-middle and bridge-and-middle sounds. Jimi Hendrix is a popularizer of this technique, and it became popular enough that the Strat got wired stock with five-position switches. Eventually the middle pickup was made reverse wound and reversed polarity, so that neck-middle and bridge middle would effectively be noiseless, humbucking positions.

It has a wide dynamic range and a 20dB attenuator, which alongside a bass-cut filter should clear out any noise that’s not supposed to get over your guitar track. Add to this an integrated suspension to reduce any vibrations when playing on stage and you get a highly functional condenser microphone that won’t capture anything else than what’s supposed to.
What would happen if four former Marshall employees got together? Well in this particular case, they formed Blackstar! Their product range includes hand-wired amps (the Artisan series) as well as products featuring different digital technologies (the ID:series). Plus, we have them to thank for the existence of the ISF system, a control that allows to switch gradually between American and British sound. In spite of the company's young life (it was founded in 2004), the brand already has many artists associated to its name like Silenoz (Dimmu Borgir) and James Dean Bradfield (Manic Street Preachers).

Slot Peghead vs. Solid Peghead (steel string models): Most models converted from a 12 fret slot peghead to a 14 fret solid peghead around 1934 (except the OM series, which went 14 fret in 1929/1930 and the style 17 and 18 models which were available in 14 fret style in 1932). Basically if the guitar has a 14 fret neck, it will have a solid peghead. If it has a 12 fret neck, it will have a slot peghead. Note there were some post-WW2 gut string and classical models (i.e. 0-16NY) and some post-WW2 special order steel string guitars (i.e. 1967-1993 D-18S) which always have a slotted peghead.
Sometimes a pitch shifter will retain the original signal while adding in the new shifted pitch.  The new shifted note can be set at a given intervallic distance from the original and will automatically harmonize any given series of notes or melody.  In short, it will harmonize the guitar by duplicating the melody at a 3rd, 5th, or whatever interval you define.
While most instruments made by Harmony and Kay were much cheaper than Martins, Gibsons or Fenders, the upper-level, more elaborate ones actually cost more money than some lower-end and even mid-priced Gibsons and Martins. A top-of-the-line Harmony, Kay or Silvertone made by Harmony featured inlay, binding and multiple pickups, switches and knobs, and cost more than a Les Paul Junior or Special and in some cases fully as much as a Les Paul Standard. While one of these instruments in near-perfect condition today might fetch $1,000 or more, it certainly would not have been nearly as good an investment as spending less to buy a Les Paul Junior and sure enough not as good an investment as spending an equal amount to buy an original 1959 sunburst Les Paul Standard.
Hi Chris. That doesn’t ring any bells I’m afraid. If your customer wants a new scheme I wouldn’t be afraid to replace the stock switch with a standard 5-way and then you know where you are. There’s always a chance that the Vigier switch is doing something funky and it started with slightly different pickup selections so the sound might change with a new standard switch. Obviously make sure you’ve got notes and photos so you can revert back to the stock wiring! Have you tried to buzz out the Vigier switch with a multimeter to see how it works? Alternatively, have you tried touching the pickup magnets with a screwdriver to see which pickups/coils are on in each switch position, that might give you some clues?
The ’62 EG-NT, EG-K and EG-Z were fairly primitive and appear to be leftover from the mid-’50s. The EG-NT had a small rectangular body with the bass side flush with the neck and the treble sticking out a bit to handle the controls. The head was stubby three-and-three with a circle Swan logo sticker and the fingerboard had painted diamond markers. The pickup looks to be the old slotted pickup of the early J-1, but may not be, with volume control. The EG-K was the Teisco version of the Rickenbacker Frying Pan, with a round body and neck with a head wider than the neck. This, too, had the rectangular head with a circle Swan logo. Markers were diamonds, the pickup was the slotted J-1 pickup, with one volume control. The EG-Z had an asymmetrical body with a short width on the bass side and a longer width on the treble side, with diamond markers and the stubby head. This had the old slotted J-1 pickup with volume control.
Martin also developed a line of archtop instruments during the 1930s. Their design differed from Gibson and other archtops in a variety of respects–the fingerboard was glued to the top, rather than a floating extension of the neck, and the backs and sides were flat rosewood plates pressed into an arch rather than the more common carved figured maple. Martin archtops were not commercially successful[citation needed] and were withdrawn after several years. In spite of this, during the 1960s, David Bromberg had a Martin archtop converted to a flat-top guitar with exceptionally successful results, and as a result, Martin has recently begun issuing a David Bromberg model based on this conversion.
I have a Samick Avion AV7 that I've been having trouble with a buzzing low E string when strumming with the first four frets. The bow is .013" and I set the 12th fret E string height to 2.5mm which helped, but not cured. I used a depth gauge to measure my frets, most measure at .043-.045" but the last two frets (21,22) measure at .052". At this point, would it be best to loosen the truss rod a 1/4 turn, or should I address the high frets, or could it be something else altogether? Thanks for the information.
Hello. I am trying to find out more about my Hohner electric guitar. I've been trying to research it online but cannot find ANY information or reference to this particular model. Some people have told me that it may have been a prototype sample that never went into production. The only reference number I can find on the guitar is a label that says Sample by Nanyo CG300G and Made in Japan. I bought this guitar around 1980-1982 when I was 13-15 years old and it is still in mint condition. I would really love to know more about it's origin.
The world is full of amps. It is so full of them in fact that it is somehow hard to choose not because there is not enough good ones, but too many of them. Which is very unfortunate, as it raises the entry level requirement for understanding what you are buying. This means that a whole lot of people get intimidated when trying to pick an amp. Like if they want a mini amp that they would want to carry with them when they go somewhere. Which is why I sat myself down the other day, bargaining all the while, and compiled a list of the best small guitar amps, for the sake of all the big musicians trying to play them. Hopefully at least some of you will find it more or less useful, since I had to categorize these according to price, sound quality, tone quality, comfort of use and even the general usefulness. What I am trying to say is, it was a lot of work.
The Les Paul Triumph bass, like the Les Paul Recording guitar was first shipped in 1971, but was based on a slightly older model, the 1969 Les Paul Bass. Functionally, these basses were very similar, although the Triumph did offer low and high impedance operation, without the need for a transformer cable. This owners manual details the basses specifications, suggests a string set, recommended action, and suggests a series of tonal settings for rock, country and solo bass playing.

Reliability is one of these. There are many different parts to an electric guitar. In addition to the body and neck being put together solidly, there are the components to consider. The pickups, controls, circuitry and output jack all need to be well made and connected securely, while the bridge and tuners should function correctly, with nothing too loose or too stiff.


For a long time Yamaha were regarded as one of the best producers of student guitars but their reputation didn't go far beyond that. And it's true that they make excellent guitars for beginners, I am one of the many who originally learned to play on their student nylon string C40. BTW I'm one of those guitarists who thoroughly recommend initially learning to play on a nylon string guitar.
Guitar culture was pervasive, whether in movie houses (“Karate Kid” Ralph Macchio outdueling Steve Vai in the 1986 movie “Crossroads”; Michael J. Fox playing a blistering solo in “Back to the Future” and co-starring with Joan Jett in 1987’s rock-band drama “Light of Day”) or on MTV and the older, concert films featuring the Who and Led Zeppelin on seemingly endless repeats.

The Omen-6 is a stripped down take on the Hellraiser, with the same sleek double cutaway design and HH (dual humbucker) configuration, but at a more affordable price point. But what's good about it is how Schecter is able to maintain the premium look and attention to detail at this lower price point, including the carved top design. While the name again implies something evil, this guitar is quite good for the price.
Do you have an old guitar that requires knowing how to repair a damaged guitar body? Read on and learn some neat tricks for repairing body damage on a guitar. Body damage on a guitar ruins the acoustics. Body damage on a guitar body really make it useless in the playing arena. If you are looking to bust out that old guitar but need some handy advice on how to repair some old damage, MadeMan has the fixes for you. This article will give you the fixes for larger damage and the annoying little nicks and teach you the way to repair them.
The Effect: Compression rose to fame in the rock and roll era, many famous musicians used (and still do) compressor pedals in order to add distinctive sustain in their performances, attracting the listener’s attention and making them stand out from the diverse instruments playing along. Some of the most famous compression pedals are the “Ross Compression” and the classic “MXR Dyna”, which have been subject to imitations and remakes ever since their original releases. Compression pedals have remained popular to this day, and are considered a must-have in many guitarist’s arsenals.
The EB-18 was a bass version with a 33.825″ scale. According to Longworth, early versions had a single DiMarzio “One” pickup and Grover Titan tuners, while later basses had a DiMarzio “G” pickup and Schaller pickups. Expect to find various combinations of those. Longworth also mentions the possibility that some might have Mighty Mite pickups, but this is uncertain. EB-18 production began in ’79 and about 5,226 (about 1,300 a year) were made until the guitar ended in early 1982.
Artist Studies are available that explain the specific playing style of a guitar hero or band like Van Halen, Albert King, AC/DC, B.B. King, Chet Atkins, Iron Maiden, David Gilmour, Eric Johnson, Freddie King, George Lynch, Jack Johnson, Jeff Beck, Jimi Hendrix, Joe Pass, John Prine, Keith Richards, Metallica, Megadeth, Randy Rhoads, Ritchie Blackmore, The Edge, Tony Rice, Wes Montgomery

The most common alloy (mixture of metals) used in pickups is alnico; this is a combination of aluminium, nickel, and cobalt. Alnico magnets were once the strongest known, but they have since been eclipsed by the rise of the rare earth magnets, which can also be used in pickups. Samarium cobalt magnets and neodymium boron iron magnets can also be used, although are perhaps less common. Additionally, ceramic magnets, based on iron oxide with strontium or barium carbonate, can be utilised.
The neck is also made of mahogany and is hand set into the body. Looking at the fretboard, we see a standard rosewood design with white binding and classic trapezoid inlays. Epiphone went with a set of Alnico Classic humbucker pickups. These are very close to what the original Gibson solution had to offer. Classic rock and blues just flow out of these, although you are more than free to crank up the gain and blast some heavy riffs.

Bass guitar tabs are basically meant to be plucked with fingers. One should try to pluck with all the four figures and if not possible then first two. One should also try to understand the rhythm of the drum and the tempo of the song, while reading the bass beginner guitar tabs mentioned below. The technique used to play these tabs is that the alphabets mentioned to the left of each string, is the string name, and have to be used. And the number represents the fret number. Try jamm'n with the bass guitar and the bass guitar tabs for beginners, that are mentioned below.

Have you ever looked at a hollow or semi-hollow guitar on the wall at your local music store and wondered how the heck they get the electronics in there? The short answer: it’s do-able, but not easy. In fact, it’s widely considered to be one of the most difficult jobs in the wide world of guitar maintenance. My tech charges extra for doing electronics work in a hollow-body, and he’s definitely not the only one.


Ovation backed off from its more exotic design directions and in ’77 introduced two more conservative models, the Preacher and the Viper, and its first solidbody basses, the Magnum I and II. The Preacher featured two equal cutaways, whereas the Viper sported more of a Les-Paul-style single cutaway, though neither would never be confused with a Gibson equivalent. Their shape was, in fact, essentially a downsized version of the Ovation acoustic outline. The Magnum shape was derived from the earlier Breadwinner and Deacon, with more contouring.
Why Martin electric guitars have never been more popular isn’t too hard to figure out. Martin, whose expertise has always been in top-notch acoustics, never really put a lot of effort into marketing its electrics. They were always well made, and, especially in the necks, clearly “Martins.” In the final analysis, however, it probably comes down to being victims of the success of their acoustic brothers, and players have just never seemed to warm up to the idea of Martin “electric” guitars. For the savvy collector with a taste for quality and relative rarity, Martin electrics remain excellent and attainable prizes.
While the bulk of new players will likely want an amplifier for their electric guitars, acoustic-driven music is still plenty popular amongst players of all skills. And while acoustics are fairly loud on their own, some players still want to pump up the volume from time to time, as well as shape their sound. And you can do all that without sacrificing the warmth of your guitar’s sound with the Behringer Ultracoustic AT108. Perfect for home practices and coffee shop performances, this amp was specifically designed to enhance the volume and tones of an acoustic guitar (or, more accurately, an acoustic-electric). It also has a secondary microphone input to amplify your voice alongside your guitar.

{ "name": "Vintage Sunburst", "skuUrl": "/Epiphone/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Vintage-Sunburst-1500000014892.gc", "status": "backorderable", "statusText": "Back Order", "skuItemType": "New", "inventoryText": "Available 11-20-2018", "inventoryKey": "available_date", "availableDate": "11-20-2018", "price": 149.00, "isOnSale": false, "msrp": 248.00, "salePrice": 149.00, "easyPayOptions":"0,0,8200002,12 Months Promotional Financing,10/31/2018,Special 12-month financing + $7 back in rewards Valid through,149.0,true,/pages/Gear-Card-Rewards.gc", "formatedIntegerValue": "149", "decimalValue": "00", "listPrice": 149.00, "isPriceDrop": false, "priceDropPrice": "", "savingsAmount": 99, "discountPercentage": 40, "promos":["coverageEligible","freeShipping","international"], "warranty": true, "sku": "site51500000014892", "shipToStore": false, "displaySku": "J40301000004000", "displayId": "1500000014892   POS #: 112318357", "serialized": false, "stickerDesc":"Top Seller", "stickerDisplayText":"Top Seller", "shipsFree":true, "condition": "New", "commerceType": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/J40301000004000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"true", "invMsgPreOrder":"false", "invMsgPromiseDate":"11-27-2018", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-Vintage-Edition-Electric-Guitar-Vintage-Sunburst/J40301000004000-00-140x140.jpg", "styleImgAlt": "Les Paul Special Vintage Edition Electric Guitar Vintage Sunburst", "freeGiftWarning":false, "freeGiftWarningTips":"", "kitCarouselItems": [], "availableInStoreOnly": false, "isShipsInternational": true, "checksum":"93895071200", "restrictionType":"", "restrictionError":"" ,"storeInfo":[ { "storeName" : "La Mesa", "storeStatus": "Ship to Store" } , { "storeName" : "San Ysidro", "storeStatus": "Ship to Store" } , { "storeName" : "San Marcos", "storeStatus": "Ship to Store" } ] }
During final construction, a small section of the outside corners is carved or routed out and filled with binding material on the outside corners and decorative strips of material next to the binding, which are called purfling. This binding serves to seal off the endgrain of the top and back. Binding and purfling materials are generally made of either wood or high quality plastic materials.

We’ve decided to give our top choice award to the Martin DRS2 dreadnought acoustic because it’s simply the best all round balance of quality, sound and price, and pretty much anyone reading this should be able to consider it as an option. The only reason you might not is if you’re dead set against a dreadnought body. Otherwise, it’s a fine choice to spend your money on.
With such a vast array of effects available, it can be hard to know where to start. One good way is to find out which effects your favorite players use. Artist interviews can be a great source of such information. Additionally, most players are happy to discuss their gear with fellow musicians. Talk to other guitar players you know, or chat up the guitarists or bassists at the local club before or after their sets.
Over the years, authentic 1950s Les Pauls have become some of the most desirable and expensive electric guitars in the world. Only 1700 were made between 1958 and 1960[citation needed]. Today, a 1959 Les Paul Standard in good condition can be easily priced between $US200,000 and $US750,000, making it the most valuable production model electric guitar ever built (however, Gibson Custom Shop reissue versions of the 1950s and 1960 Les Paul can be purchased for less, between $US3,000-$US6,000 – certain artist signature model versions of the guitars are considerably more expensive). Jimmy Page has been offered 1 million pounds (1.6 million USD) for his “number 1” 1959 Les Paul should he ever decide to sell it.[22]

A way to increase the usability of the sound acquired this way is to wire a capacitor in series with the pickup that has its electric polarity reversed. This filters out that pickup's lower frequencies and thus preserves the corresponding frequencies from the other pickup. The resulting sound is fuller and stronger, yet still different from the standard in-phase combinations, resembling the sound of a "cocked wah" (a wah-wah pedal set in a fixed position). The capacitor used for this is usually in the 20–100 nF range.[23]
Naturally, if a seller can get more money by calling what they have a “lawsuit guitar”, they’re going to do it. Unfortunately, some writers who should know better have taken to using the term for any old Japanese lookalikes, copys, knockoffs, etc, of (mostly) American guitars. Some sellers are using terms like “lawsuit era” or “pre-lawsuit” which don’t mean anything at all.
It has a sensitivity of 96 dB, just two units short of the M50x’s 98, but the maximum input power is less than half of that model’s, at 700 mW. The impedance is somewhat higher at 47 W vs. the M50’s 38 W. Besides the price, another identifiable upside would be the lower weight, of 6.7 oz, a feature that won’t be easy to discard after spending the whole day with the headphones on.
{"eVar4":"vintage: guitars","eVar5":"vintage: guitars: electric guitars","pageName":"[gc] vintage: guitars: electric guitars: lyle","reportSuiteIds":"guitarcenterprod","eVar3":"vintage","prop2":"[gc] vintage: guitars: electric guitars","prop1":"[gc] vintage: guitars","evar51":"default: united states","prop10":"brands","prop11":"rickenbacker","prop5":"[gc] vintage: guitars: electric guitars","prop6":"[gc] vintage: guitars: electric guitars","prop3":"[gc] vintage: guitars: electric guitars","prop4":"[gc] vintage: guitars: electric guitars","channel":"[gc] vintage","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] vintage"}
vintage harmony h75 hollow body guitar ser 519 1966, vintage 1950s vega odell model e130 hollow body electric guitar in case, vintage 1960s harmony h56 rocket hollowbody w hsc, vintage baldwin electric hollow body 12 string arch top awesome sound and player, vintage egmond hollowbody electric guitar gold foil pu make offer, vintage circa 1956 gibson es175 d hollowbody electric guitar white refin p90, vintage 1966 conqueror 335 shaped hollowbody sunburst arch top hh bigsby style, vintage vantage vsh455 hollowbody electric guitar with original case no reserve, vintage rare galanti hollowbody electric guitar super funky 1960s, vintage 1968 gibson usa johnny smith hollowbody guitar rare doublepickupwohsc, vintage 60s japan mij teisco del rey ep10t thinline hollowbody sharkfin guitar, 1966 harmony h74 hollowbody electric guitar original case clean vintage, vintage kapa series 500 hollowbody electric guitar amp; case usa, vintage bruno conqueror made in japan mij electric guitar hollow body , 1980 ibanez artist as200 vintage hollow body electric guitar, 1967 gibson usa es33512 vintage semihollowbody 12string electric guitar, vintage 1970 gibson es175d hollow body electric guitar, vintage hollowbody electric guitar harmony kay silvertone must see no reserve, 1964 gretsch tennessean 6119 vintage hollowbody electric guitar w bigsby , vintage experienced 1967 harmony h72 hollow body guitar, vintage circa 1967 framus atlantic 5113 semihollow body original cherry red , vintage original circa 1969 aria es335 copy semihollow body electric guitar, vintage 1966 baldwin burns vibraslim semihollow body guitar clean no reserve, awesome vintage hagstrom viking super rare 12 string hollow body w low action, beautiful vintage harmony h75 hollowbody electric guitar, vintage 1960s harmony silvertone model 1429l hollowbody electric guitar w ossc, vintage 1967 gretsch rally hollow body electric guitar bamboo yellow orig case, vintage 1961 epiphone broadway arch top hollow body electric guitar natural , vtg conrad brown sunburst electric guitar es 335 type hollow body wcase j0330, vintage 1970s ibanez model 2358 semihollowbody electric guitar al caiola copy, vintage 1988 gibson es335 jc showcase edition electric hollowbody guitar w case, rare vintage 60s egmond electric hollow body guitar from holland cool, vintage circa 1969 harmony rebel semihollowbody electric guitar sunburst ossc, vintage 1960s vox super lynx hollowbody electric guitar sounds amazing, vintage usa 1972 harmony rebel h81 hollowbody electric guitar near mint wtags, vintage 1954 gretsch 6186 clipper hollywood hollow body w case rare nice, vintage circa 1969 greco hollowbody double pickup electric guitar brown w ssc, vintage circa 1966 made in japan semihollow body electric guitar sunbust clean, 1967 vintage guitar aria diamond 1202t hollow body no case free shipping used, vintage 1966 harmony h59 rocket 3 hollow body red burst finish rare nice
Unfortunately there are a few who are not too happy with with some of the default patches, they caution that the PODHD500X is not a plug-and-play unit. While you can get good tones with a bit of tweaking, you can get even better tones with more experience, so the learning curve can be a bit steep for some. For best results, you ought to research the actual gear that your favorite musicians use, along with their settings and use them as your starting points to creating your own tones. Thankfully, there are user made presets that you can also use as base for your own virtual signal chain.
I cut my template with a jig saw and a fine tooth blade to make sure it kept a straight edge. Then i mounted it to the body blank using small screws in the ares that would be routed out later like the neck cavity area and where the pick ups would be. You will want to start routing a bit outside your line or the edge of the template so you can get you router bit to the depth it will need to be at for the ball bearing to follow the template. I use a 1/2"x1" bit with a ball bearing guide on top.I make several passes around the body, lowering the router 1/4" at a time for smooth easy cuts. Once you have made your pass were the bearing runs along side the template, it is much easier to rout and you will end up with a nice squared edge to the body.

Of music written originally for guitar, the earliest important composers are from the classical period and include Fernando Sor (b. Spain 1778) and Mauro Giuliani (b. Italy 1781), both of whom wrote in a style strongly influenced by Viennese classicism. In the 19th century guitar composers such as Johann Kaspar Mertz (b. Slovakia, Austria 1806) were strongly influenced by the dominance of the piano. Not until the end of the nineteenth century did the guitar begin to establish its own unique identity. Francisco Tárrega (b. Spain 1852) was central to this, sometimes incorporating stylized aspects of flamenco's Moorish influences into his romantic miniatures. This was part of late 19th century mainstream European musical nationalism. Albéniz and Granados were central to this movement; their evocation of the guitar was so successful that their compositions have been absorbed into standard guitar repertoire.
The transformer matches the impedance of the driver amplifer to the reverb driver coil and allows a dual phase driving signal to power a reverb coil with one grounded side. The transformer is a standard "70 volt" audio line transformer that is often found on PA systems. One reader reported having good results using a Mouser 42TU013 (1K to 8 ohm) transformer. If you can find a reverb tank with a high impedance driver coil, the transformer may be eliminated, the driver coil will require isolation from ground.
Coming from the back of its introduction in 2006, this Hellraiser series of Schecter’s electric guitar is proving to be a game changer in the strumming market, by excelling far ahead in areas like sight, sound, durability, quality, and affordability—a stark definition of a unique electric guitar. These set of Hellraiser guitar are not only beautiful but also versatile.

Once you've mastered a few songs on the guitar, you may want to record what you can do so others can hear you shred a wicked solo. Or you may want to use your recording to help improve your skills. In either case, recording your electric guitar outside of a studio can result in poor sound quality that is less than desirable or noise complaints. Depending on your situation and equipment, there are many factors you'll likely have to tweak on your way to getting the best recording, but with a little effort, you'll soon be able to listen to an awesome recording of your musical ability.
Many music purists prefer analog effects. Since they don’t use digital conversion, the signal (purists argue) is less prone to loss, and is more pure as a result. It’s true that digital conversion can cause some natural artifacts of the original sound to become lost, and can sound more “processed.” However, as digital technology has evolved, this has become less of a consideration. Digital effects have the advantage of versatility and precision. Today’s multi-effects processors only exist because of digital processing; many effects can be achieved in a single unit through sheer processing power. Digital signals can also be used to control a wider range of parameters.
The guitar is just a small step on being a guitar player. Having a budget friendly guitar to practice and learn with is suitable enough at this stage. The key to success really depends on how you practice and dedicate yourself on learning how to play. As long as you have a decent sounding playable guitar to begin with and has the quality that can last you in years to come. You’ll be all set.

Unfortunately, it appears it is no longer possible to grab a Standard MIM Telecaster for under $500. Still, the Standard Telecaster remains a solid option when it comes to reasonably priced guitars, and it is a great alternative to the American Tele. However, if this increase doesn't set well with you, and you aren't digging the Modern Player Telecaster Plus, I suggest checking out what Squier has to offer.
Mahogany is a durable wood, often described as dense and that is used in the construction of guitars. The main advantage of purchasing an instrument made from this material is the fact that it highlights the unit’s bass and midrange. Therefore, if you are into mellower tones, this is the material that you should pay attention to. The resulting guitars made from this material are usually brown.
Joe is a musician, engineer, and producer in NYC. Over the years, as a small studio operator and freelance engineer, he's made recordings of all types from music & album production to v/o & post. He's also taught all aspects of recording and music technology at several NY audio schools, and has been writing articles for Recording magaz... Read More
Cool guitar! And you’re right— most Harmony guitars aren’t worth much, or in other words, they aren’t very collectible. That said, I wonder how many guitarists reading this column started out learning to play on a Harmony. There are hundreds of thousands of Harmony guitars out there, and though these are mostly entry-level instruments, they’re very much a part of guitar history.
I’m also going to go out on a limb and suggest the earliest Univoxes also included the ‘Lectra, a version of the one-pickup Aria 1930 violin bass (made by Aria). These were basically violin-bodied basses originally inspired by the Gibson EB-0, and popularized among imports by Paul McCartney’s use of the Höfner violin bass, copied by EKO. This was a hollowbody with no f-holes, Cremona brown finish, single neck pickup, bolt-on neck with position dots along the top of the 22-fret bound rosewood fingerboard. Strings anchored to a covered bridge/tailpiece assembly.

Though because of this flexibility, it can be hard to figure which of the many types of electric guitar is going to be a good fit for your needs. Thankfully, if you’ve arrived at this article you’re going to get all of the information that you need to make an informed decision on which body styles are going to be worth considering for your genre of choice.
Giannini guitars were (and are) made by the Tranquilo Giannini S.A. factory, Carlos Weber 124, Sao Paolo, Brazil. They are generally known for being well-made instruments featuring very fancy Brazilian hardwood veneers, as well as for the strange-shaped asymmetrical CraViola models. Probably the most famous, indeed, perhaps only famous, endorser of Giannini guitars was José Feliciano. No reference materials were available on the early Giannini guitars. A catalog from 1971 is available, with a snapshot of the line that probably goes back at least a decade, and certainly forward.
Besides instrument inputs and speaker outputs (typically via 1/4" jacks), an amp may have other inputs and outputs. These can include an auxiliary input jack (sometimes with its own level control, for a drum machine), "send" and "return" jacks to create an effects loop, a “line out” jack and an extension speaker jack. Practice amps sometimes have a 1/4" headphone jack, or stereo RCA or mini jacks for connecting a CD player, portable media player or other sound source. Some guitar amps have an XLR input so that a microphone can be plugged in for singing. Guitar amps that include a mic input are in effect small, portable PA systems. Some amps, typically bass amps, have an XLR connector to provide a balanced output from the preamp section to go into a PA system or recording input.
Effects pedals, or stompboxes, are effects units designed to sit on the floor or a pedal board and be turned on and off with the user's feet. Typically, effects pedals house a single effect. The simplest stompbox pedals have a single footswitch, one to three potentiometers (knobs) for controlling the effect, gain or tone, and a single LED display to indicate whether the effect is on or not. More complex stompbox pedals have multiple footswitches, numerous knobs, additional switches and an alphanumeric display screen that indicates the status of which effect is activated. An effects chain, or signal chain, may be formed by connecting two or more effects pedals together.
In this buying guide, you’ll learn the essentials of what effects pedals do and which ones to look for depending on the kind of tone you want to experiment with. Here’s the quick overview: effects pedals (also called “stompboxes”) are electronic devices that connect in-line with your guitar and amp to change the signal going through them. Some work with analog circuits and some are digital, but they’re all powerful tools for shaping your sound in endlessly creative ways.
Amps available in ’61 included the large HG-8 (recommended for use with the EG-TW and Harp Guitar), the Amp-75C, Amp-73C, Amp-72A, Amp-72B, Amp-72C, Amp-71A, Amp-71B, Amp-71C, Amp-30, Amp-4C, Amp-15 and Amp-86 bass amp. These came in a varity of shapes, mostly with either a single color covering with a tweed grillcloth, or the two-tone Amp-30 or the two-tone Amp-15 with a cross-shaped grillcloth area. All had the Swan-S logo. These were most likely still all tube amps at this point in time.
The strings on your electric guitar have a major impact on its sound and playability. If you’ve taken a look at the huge Musician’s Friend guitar string assortment, you’ve likely realized that there’s a lot to consider in figuring out which strings are right for you and your instrument. Keep reading to find the strings that best match your electric guitar, music, and playing style.
That is true, but without the many fine guitarists of today, who will inspire the gifted musicians of tomorrow. Musicians are artists and it would be quite dull if they all copied each other and sounded the same wouldn’t it? Whether we like it or not the world keeps on spinning regardless of what we want, think or do. Enjoy the gifts that are shared today, because we’re not guaranteed a minute more.
Martin & Co is without a doubt one of the most reputable acoustic guitar makers in the world, so if you or someone you know is planning to spend a lot of dough on an acoustic guitar - it best be a Martin. One of the more recent releases from Martin that deserve special mention here is the 00-42SC John Mayer, a signature guitar inspired by the classic Stage Coach(SC) design, which were prevalent in an era where small bodied parlor guitars were highly favored.
Marr, once a member of Electronic with Bernard Sumner of New Order and Neil Tennant of Pet Shop Boys, has played on a number of records and contributed to numerous other high-profile projects, including his recent stint in Modest Mouse. This weekend, Marr returns to Denver in support of his debut solo album, The Messenger, and in advance of the show, we spoke with the charming and intelligent guitarist about how he got the sound for "How Soon Is Now?" and his signature model of the Fender Jaguar.
Most users are happy with what they got for the money, from its wood quality, to the included hardware and electronics. As expected, many of its buyers are fans of the Les Paul Jr who want to try their hand at customizing their own straightforward rock machine. Surprisingly, there are some who are happy with its default configuration, including the feel of the neck, the sound of the P-90 pickup and the quality of the tuners.
Rickenbacker: From making world’s first electric guitar to making the most iconic guitars of Rock’n Roll, Rickenbacker has a history of innovations in guitar industry. Their guitars are still made in the old way. Owning a Rickenbacker is pretty much like owning a classic muscle car, yes there may be more modern guitars out there but no one’s got the mojo of a Rickenbacker.
Music is a passion for many people around the world. There are possible over 3000 musical instruments in the world, right from the most traditional ones to the highly sophisticated modern ones. Guitar is one of the most stylish modern musical instruments known to man. A lot of young stars are actually inclined towards playing a guitar. The guitar is an instruments which produces sound on the strumming of strings attached to the strand, which is like a long bar on the upper portion of the guitar. There are a number of manufacturers who manufactures these amazing instruments. But question is which the best are? Here is a list of top ten brands of guitar to choose from:
SolidBody (2008) – Taylor’s take on a traditional solid electric guitar. Made from a solid slab of wood with cavities only for the pickguard or direct mounted pickups, and the bridge. Designed from the ground up, each SolidBody model features solderless pickups or a solderless pickguard which permit for musicians to effortlessly change the sound of their guitar. The SolidBody line is fully customizable with a wide combination of wood, colors and electronic configurations, and single or double cutaway options which enables anyone purchasing a SolidBody to get the sound and look that they want. All options are available for customization through Taylor’s SolidBody Configurator on the Taylor website.
The pickup coils are wired to the amplifier through an electrical circuit. The circuit usually also contains volume and tone controls, which allow the basic sound to be adjusted by turning knobs on the guitar body. A guitar with two pickups will have four knobs on its body: one to adjust the volume and the tone of the sound from each pickup. More complex circuits can be added to change the sound of an electric guitar in all kinds of interesting ways.
The Tele is often called a workingman’s instrument for its simplicity.  It also happens to offer tons of tone variants, just like the Strat.  The neck pickup, with its distinctive “lipstick” look, can go from perfect blues tones to jazz, just by rolling back the tone knob.  Danny Gatton was known to take full advantage of the many sounds the Tele could produce, even in one song, by rolling the tone knob to produce the “wah wah” effect that most players achieve through a foot pedal.
Time to turn our attention back to the guitars themselves. The following are some of the better low-cost electric guitars available on the market today; refer to an anatomy of electric guitars to see definitions of guitar pieces and places. When you're deciding, go to a store and try them out for heft, comfort, stability, sound quality, and appearance. Shop around, comparing, for instance, online prices against local store prices. This is an investment, so choose wisely.
John Mayer: features a select alder body, a thick C-shape maple neck with African rosewood fingerboard and 21 Jim Dunlop 6105 narrow-jumbo frets, American Vintage hardware and a trio of “Big Dipper” single-coils with a special “Scooped” midrange voicing and 5-way pickup switching. Available in a variety of finishes, including black with 3-ply mint green pickguard and gold hardware, 3-tone sunburst and olympic white with brown shell pickguard and as a limited-edition version with a cypress mica finish, white vintage amp knobs and a 3-ply parchment pickguard. In 2010, Fender also released a limited 500 run of John’s personal BLACK1 strat.
I have a Palmer P 33 acoustic (hand-crafted etc), that I bought second hand about 20 years ago for £80. It still sounds and looks superb and rarely loses its tuning. (Probably better than my newer Tanglewood.) I can't find out anything about it. However, somebody out there must have made it. Surely that somebody knows something about them! Do they never go on the internet! Pete.
The Vintage El Dorado Leather Guitar Strap is meticulously hand-tooled in traditional Western motifs by leather artisans with decades of experience. Each strap is an individual and unique work of craftsmanship that you'll be proud to display on your guitar. The designs date back to late 19th century Western leatherwork, used extensively in the decoration of saddles, saddlebags, belts and holsters.

Gibson has been producing the Les Paul Studio electric guitar since 1983. One of the company’s lower-priced models, the Les Paul Studio was designed to attract guitar players who wanted to have the much-admired Les Paul sound without shelling out cash for cosmetic features found in upper-tier models like the Les Paul Standard. This is why the older Les Paul Studio models did not have headstock inlays and binding on the neck and body.
Festive music track with cheerful and happy mood, with “We Wish You A Merry Christmas” song melody. I’ve included in pack different logo and looped versions of this track, for your comfortable using. This celebratory track can be used for Winter Holyday projects, children arcade games, as New Year jingles, advertising and Youtube commercial video. Enjoy!
Here we JUST SOLD OUT: another excellent FG160 for your serious consideration the Yamaha FG 160 Acoustic Guitar Made in the early - mid 70's from Taiwan factory. This example was built well over 35 years ago and was built to very high detailed standards as well as some of the best grained Mahogany woods seen in this time period ( see pics for those detail ) in that time period these were meant to compete with the great M@r#!n and now this Yamaha is quite well aged too and is a REAL vintage guitar in its own right sounding SWEET with its well aged woods with really beautiful patina of a true vintage instrument. This one has the Amber/Tan label and not the Red Label but the golden label. The frets are very good - original I did a quick dressing of the lower 5 or so frets and polished all. The guitar has it's natural age and character with beautiful patina and it has been played of course its not new its over 35 years old with a few insignificant minor nicks,dings from a well loved and adult respected instrument. This fine example is here and in stock... We upon receiving have remove the strings cleaned and detailed the guitar oil rosewood and polish finish, We have * upgraged* its TONE by installing a Martin BONE nut and compensated BONE saddle set for improved tone resonance over the old plastic stuff so she has a nice deep ring to its tone now and this guitar to plays very well Yamaha's and they are truly amazing instruments very well compared to a much more expensive brand guitar as you may have heard…. These FG’s are known for there fine construction and playability with amazing tone for this kind of money… to get a vintage aged tone woods instrument built this well and in this kind of condition make this FG160 the one to own for a song! Re: condition its over 35 years old and is BETTER than average This guitar has no cracks, no finish checking no warped top, no loose or pulling bridge Its neck has a real nice feel to it and is a medium - slim profile = feels like M@r#!n D-28ish substantial but not too fat - Just right! 1-11/16ths at the BONE NUT Play action is very good see pics Its a standard Dreadnought Acoustic and is Identical to the Yamaha FG180 This is an excellent vintage Yamaha FG160 You will be pleased with its sound she has good bones its over 35 years old and has proudly stood the test of time there is no reason this guitar will not continue to serve another 35+ years with average care. Beautiful Patina only seen on real vintage guitars Let me know if you have any questions ore are ready to purchase email Joe at JVGuitars@gmail.com.

Try different gauge strings. As you know, guitarists can be creatures of habit. But heavier strings can help both your tone and fingering strength, while lighter strings may suit bigger bends. Experiment! Billy F Gibbons has the thickest tone but his top E is only a .007. Stevie Ray Vaughan’s top E was a .013. Changing string gauge may just bring out your best inner-self.
: This vintage YAMAHA is one of the greats folks and here for your serious consideration today at Joe's Vintage Guitars.... This is the Classic Vintage Yamaha FG-200 - Nippon Gakki body seems the same specs as the famous FG180...hummm? interesting She's been lovingly played for nearly 40 years,its beautifully aged now with a great feel & patina only found on real vintage guitars of this age and caliber. This guitar really has nicely opened up over the past 40 years and you just don't get booming bassy tone like this one with a new guitar thats for sure. This example is not mint but is beautiful in its own right, it does have a few nicks, dings and wear but nothing really bad at all really she just looks the part of the 40 year old Martin D28 vintage guitsr. A lot of guitar for not a lot of cash... Vintage aint goin down..get her at a great price today! Let me know...thanks for your interest, Joe email me: gr8bids@comcast.net This is an early one from the Nippon Gakki plant and has a surprising boom even for or a 200 same as our great old red lable FG180 for that matter with no real decernable diference. I cannot find a serial number but is believed to be late 60's - early 70's This old girl has Excellent low end sound!!! and tone on this guitar is wonderful - it really booms! Condition: Average vintage wear wich includes minor pick wear, scratches dents & dings for an old vintageguitar. but no cracks to be found, straight neck, trussrod is functioning properly, very good frets still playing well all the way up & down the fingerboard with no funny buzzes or dead spots... Frets 1 - 5 ( cowboy cord area )have medium play wear but still plenty of life remaining no problemo. action is very good at 3/32 1st E string @ 12th fret. Tuners are the original and in excellent working order. Bridge plate is securely fastened to top. We have just as a precationary installed A PlateMate brass plate has now been installed to any prevent further wear to bridge plate which is common among these vintage guitars. This brass plate has also contributed to its big booming tone now is even a more rich sounding competitor to a vintage Martin D-28... FRESH SET UP...with Martin Bone & Saddle... this guitar is a wonderfull fun guitar to play lots of bang for the buck factor here.. This guitar is overall a very solid well built guitar that is standing the test of time it also is a great sounding vintage guitar that plays very nicely. Ya can't go wrong with this wonderful vintage Yamaha FG Nippon Gakki guitar Has a new bone saddle and Martin Silk Steel strings. No case included but will protect and properly package for shipping. PlateMate product works very well and is easily removed if desired. To my ear it enhanced this boom-box's sound quality and is described by the manufacturer as follows: If you want to protect and enhance the sound and tones and balance out string volume of your acoustic guitar, Mitchels Plate Mate is the way to go. Mitchels Plate Mate is a small piece of brass that is applied without using or altering of tools, and is installed as fast as you can change a set of strings. This was invented and patend mainly to prevent damage caused by ball-end strings on the acoustic guitars bridge plate, it is also proven to enhance volume, tones, and balances out string volume by one of the best acoustic guitar makers in the world. Mitchels Plate Mate will protect your guitar from ball-end strings pulling up threw the bridge plate and possibly cracking the bridge or pulling the bridge off the top of your guitar which would be a very expensive repair bill. It also protects your bridge pins, and saddle by making the string windings stay down in the string holes where they belong. I have used Mitchels Plate Mate in guitars priced from $100 to $50,000 it doesnt matter the price just protect your prized posetion or investment. .

Specs for your guitar include an ash body and carved maple top (rosewood was an option) bound with an abalone border, and a 5-piece maple/rosewood through-body neck. Other features include the bound 22-fret ebony fretboard with brass circle inlays, a matched-finish headstock with abalone border, 3-per-side tuners, two exposed humbuckers, and controls for each pickup. Its ivory finish is probably the most desirable color for this model, but the guitar was also available in a natural finish that highlighted the maple or rosewood carved top.
The use of "full range, flat response" (FRFR) amplification systems by electric guitarists has received an extra impetus from modeling amplifiers. Before widespread availability of modeling, guitarists did not commonly plug electric guitars straight into PA systems or powered speakers, because most genres relied on the tonal coloration of a regular guitar amplifier setup—from the preamplifier, equalization filters, power amp, guitar speakers, and cabinet design. The FRFR approach assumes the tone is shaped by sound processors in the signal chain before the amplifier and speaker stage, so it strives to not add further coloration[20] or dedicated combo-style amplifiers with a broad frequency range.[21] Such processors can be traditional guitar effects, a modeling amplifier (without power amplifier), or a computer running tone-shaping software.[20] Using a modeling amp or a multi effects pedal used with line level output, a guitarist can plug in the guitar into a flat response mic input or into a keyboard amplifier.
Delay pedals take your original signal, a guitar chord or note for example, delays it and plays it back exactly how the pedal hears it the first time. It can either play the note back once or multiple times depending on your settings or “feedback time”. Often, you’ll see Digital Delay pedals as well as Analogue Delay pedals. The major difference is that digital delay pedals will offer longer delays and a ‘cleaner’ exact sound, however guitarists often prefer the analogue sound for all the subtle nuances and slight unpredictability in sound. This comes down to personal preference but both options sound great.
The vast majority of bass amps in the 2010s can be powered solely by AC mains power, obtained by plugging the amp into a wall socket. Inexpensive practice amps may have the AC mains plug hardwired into the unit. Middle-priced to high-priced amplifiers typically have a removable cable and plug, as used with PC computer towers. The benefits of having a removable cable and plug is that if the cable becomes worn or damaged, a new cable can easily be replaced by a layperson. If a hardwired AC mains cable and plug becomes worn or damaged, a qualified technician or electrician will typically be required to replace the cable and plug. Most amps are designed to work for a single voltage. A small number of expensive bass amps designed for touring professionals have user-selectable voltage, which enables a bassist to play with same amp in North America and Europe. A small number of small combo amps can run on both AC mains power and battery power. This enables bassists to play outside where there is no access to power (e.g., for busking on the street). Amps that are battery powered may have a 12 volt input, enabling the unit to be connected to a car battery with alligator clips.
Mikko, spot on. Even light wood has density, and there comes a point in solid body electric guitars where how dense any piece of wood is only makes a difference acoustically. The point you made about how a guitar feels when you're playing it is sound, though. Its weight and acoustic resonance will affect how you respond to it and how you attack it (same for neck thickness and profile), and that will account for the preference we have for one guitar over another of the same model.
• Why frets come loose: Wear from string contact, fretboard drying and jarring mid-gig or during transportation can cause frets to pop loose. And if binding loses moisture, that can cause the ends of frets to rise or be exposed. These all create troubles that can wrongly be blamed on the more typical problem of fretwear, but in these cases dressing or replacement isn’t necessarily the answer. If there’s enough fret wire left, a loose fret can be reseated in its slot along the fingerboard, and a skilled luthier can often fill the gaps between the binding and the fret ends.
Gibson Les Paul and Fender electric guitars can retail for several thousands of pounds, but electric guitars for beginners are available for less than £100. One example of a cheap electric guitar is the LA Electric Guitar + Amp Pack, which features everything a beginner needs to start playing the guitar right away for under £90.00. It includes a 15 watt guitar amp with 6.5" speaker for practising, a guitar lead, a strap, a padded gig bag, a set of spare strings, a pick and a 2-year warranty. The electric guitar itself has a neck made from maple - the most common type of wood used in necks - which helps to expand on the treble sounds of a guitar due to its hardness. The guitar is capable of producing a wide variety sounds, thanks in part to its 3x single coil pickups with a reverse wound middle pickup, which enables users to experiment with playing different styles of music.
Dogwood Guitars is a full-service setup and repair shop. We are equipped to handle all of your acoustic and electric guitar adjustment and repair needs. The prices listed below are labor estimates and do not include parts such as new strings, bone blanks, fret wire, etc. I give free no-obligation evaluations of any guitar so that you can make an informed decision about your instrument and its care. Guitars are like cars; they need some routine maintenance to perform at their best.

The American David Schecter founded his company in 1976 in order to produce spare parts for guitars already available (especially Fender and Gibson). But since 1979 the brand has been manufacturing its own guitars. In the beginning they had only Fender-based models but nowadays, Schecter guitars are clearly conceived for hairy players (but not exclusively), with models like the Hellraiser or the Damien. Among their most famous users are Billy Corgan, Eddie Vedder, Pete Townshend, Mark Knopfler, Matthew Bellamy... And the brand also presented its first amps at the latest NAMM show.
The brands and individual guitars that we have selected are based on a combination of our joint 80+ years of experience and the ratings and feedback from people who have bought them. The leading brands are dominated by Martin and Gibson/Epiphone as you might expect, and there's not a lot of change this year in terms of brands expect that Seagull has earned their way back into this list at the expense of Fender - we had to make the cut somewhere.
Definitely, Diary of a Madman is like…the groundwork for so many great songs out there today. And if you listen to that live solo after Suicide Solution, which is only done live, it's just crazy what he could do that you didn't think he could do. If he was still alive, even if he left Ozzy, we would have seen even better stuff from him. Crowley and Crazy Train were actually more watered down marketable songs. That's more or less why Randy was GOING to leave Oz in the first place.
 Best Answer:  First, make sure you have new or clean strings that aren't dead. You should hear a metallic harmonic overtone to picked notes particularly on the low E, A, and D wound strings. If your low E sounds in tune but makes a flat dull boww boww boww instead of dang dang dang when you pick change them. Set your amp up for a fairly bright sound clean, playing off the bridge pickup. Make sure the guitar volume knob(s) are rolled all the way on and tones are all the way up, no roll off. If you can't get a nice clear clean sound that doesn't sound distant and muted then you have some issue with the guitar electrics or amp. If you're playing off the neck pickup that's a big muddier right there. The neck pickup is good for clean rhythm playing, jazz, and for a hollow warm tubey sound on single notes but tends to muddy overdriven power chords. Once you have the amp set for a bright clean sound that's not too brassy (if it has a master volume in addition to a gain or channel volume set the gain or volume low for a clean sound and use master for output level, let the RP90 do the effects work, not the amp preamp for now.) bring in the RP90. I'm not familiar with it but try it on a few overdrive and distortion settings. If you've only been an acoustic player high overdrive or distortion "power steering" takes a different play style. 

Ibanez is a Japanese music instruments manufacturer that has produced some of the most iconic guitars of the 20th century. Established in 1908, the company started to design the first guitars in 1957. Ibanez was one of the first companies to gain popularity in the US and Europe markets. It also was the first to mass-produce 7- and 8-string guitars.
Wah – This type of pedal was a Jimi Hendrix favorite, and you’ve probably heard the original “Cry Baby” in a lot of music. It was the first wah pedal to find success, and paved the way for others to follow. The Cry Baby is an example of manual wah, controlled by a rocker pedal that adjusts the level of treble response dynamically as you move it. Some modern wah pedals, by contrast, are “auto-wah effects,” which do the same thing but use presets for control instead of live input from your foot.
Electric guitars have been popular and prominent for decades. For quite some time, being a left-handed musician was considered a hindrance and artists often had to make due with a right handed guitar. Now, there are plenty of fantastic options for lefties so they can make their mark on the music world. As a left-handed musician you probably know that many legendary artists were lefties too- Paul McCartney, Jimi Hendrix, Kurt Cobain, and Dick Dale are just a few examples of musicians who paved the way for up and coming lefties to seriously rock out. Electric guitars are perhaps the most notable and distinctive instrument in pop and rock music. Heavily used on stage and in the recording studio, the electric guitar provides some of the most memorable parts of a song or tune.
What we're looking at here is a standard Les Paul body made of mahogany and finished with an attractive vintage sunburst pattern. There's also a gorgeous heritage cherry sunburst and a straight ebony finish option as well. It features a pair of 700T humbuckers, one at the bridge and one at the neck position. These are pretty basic in nature, but their performance is more than good enough even for more experienced players and important recordings.
My mom just gave me a Norma FG12 acoustic guitar my father bought for her back in the day. It is in the original box and i honestly doubt it ever made it out of the box! It appears in pristine condition but I know absolutely nothing about guitars. I really don't care to learn how to play it. I would like to sell it but have absolutely no idea how much it is worth nor know the best place to try to sell (?ebay perhaps) Any suggestions/thoughts would be most appreciated. Thanks!
Valco manufactured Spanish acoustic guitars, metal-bodied resonator guitars, electric lap steel guitars, and vacuum tube amplifiers under a variety of brand names including Supro, Airline, Oahu, and National. They also made amplifiers under contract for several other companies such as Gretsch, Harmony, and Kay. In the 1950s they began producing solid body electric guitars.
This book emphasizes tabs with the accompanying music notation. It’s not a long book and one that a beginner will likely outgrow at some point. However, it provides a good introduction to get you playing songs you’ll recognize fast. It does a fine job of explaining everything the newbie needs to know including how to position yourself. Build those good habits early!
Hand built with the same precision as our larger guitars, just 25% smaller.  Great for travel, ideal for children struggling to get their arms around full size guitars, fantastic second guitar for the office.  Because it has a smaller box design our Travel will have a smaller sound (like any smaller guitar) but our Travel Electric with built in auto tuner allows you to plug into any amplifier or PA system giving you the same power as our full size guitars.
The so-called modeling amps can be said to differ from both tubes and solid state ones as they employ modern processing technology to apply preloaded characteristics to the sound. This can alter the output in a variety of ways, from imitating certain classic styles to rendering something entirely new. Needless to say, they are favored by cover bands and electronic music fans, but many guitarists don’t appreciate their “artificial” sound, although they can serve as good practice amps.   
As the market for iOS devices and apps has grown, so has the availability of affordable stompboxes and processors that can store downloaded effects. Being able to sample, purchase, and download effects through an iOS app or digital download gives you access to a whole new palette of sounds. Though relatively new, in years to come this may well become the way in which most players will assemble their effects libraries.
While tube technology is still considered state-of-the-art in countries where a potato is regarded as a square meal, these days solid-state and digital amps offer excellent tone for a lot fewer bucks, and with fewer maintenance headaches. However, tube tone is still considered the standard by many top players. Take a blind listening test, and let your ears be the judge.
I am writing this due to the mixed reviews that I read before buying this. This is a really powerful device. I have had a POD 2.0 for years. This is just as good and is also small, portable, and inexpensive. Most of the criticism that I read is that it is not well made and durable. It is well made, but I don't think it is designed for gigging. It is perfect for practicing or interfacing with a home studio. If this is your application, then you will be very satisfied. One other thing that I found true of this and similar devices that I own is that the quality of the headphones makes a big difference. If you use studio quality headphones it will sound great, if you use music player headphones it will just sound good. I haven't ... full review
If you feel you’re ready for a new and better axe or are keen on starting your musical journey with an awesome electric guitar, check out the models we’ve reviewed below. All of these electric guitars have become fast favorites since they were released to the music-loving public. We’re sure you’ll find one or two that would meet all of your requirements and fit your budget.
The steel-string beauty is crafted from solid Sitka spruce on the top, which features solid Indian rosewood back and sides, and a slim mahogany neck and rosewood fretboard. You’ll notice some impressive decoration on the BR-160 (as we mention in our full review), including an exclusive Dalmatian-style tortoiseshell pickguard, accurate 14:1 butterbean-style tuners, and an elaborately decorated motherof-pearl headstock.

The three pickups were originally identical in their construction. With the rising popularity of using pickups in combination, Fender introduced a new feature in 1977 coinciding with the standard 5-position switch; a reverse-wound, reverse-polarity middle pickup. As the description implies, the magnetic polarity of this pickup is opposite the other two, as is the direction of the wire winding around the bobbin. This provides a hum-canceling effect (removing hum induced by poorly shielded, medium to high output AC devices) in positions 2 and 4 on the selector switch. This principle had been known for many years beforehand, being applied in the form of Gibson’s humbucking pickup and Fender’s own split-coil pickup used on the Precision Bass.


An amplifier stack consists of an amplifier head atop a speaker cabinet—a head on top of one cabinet is commonly called a half stack, a head atop two cabinets a full stack. The cabinet that the head sits on often has an angled top in front, while the lower cabinet of a full stack has a straight front. The first version of the Marshall stack was an amp head on an 8×12 cabinet, meaning a single speaker cabinet containing eight 12" guitar speakers. After six of these cabinets were made, the cabinet arrangement was changed to an amp head on two 4×12 (four 12" speakers) cabinets to make the cabinets more transportable. Some touring metal and rock bands have used a large array of guitar speaker cabinets for their impressive appearance. Some of these arrangements include only the fronts of speaker cabinets mounted on a large frame.[25]
The modern classical guitar is usually played in a seated position, with the instrument resting on the left lap - and the left foot placed on a footstool. Alternatively - if a footstool is not used - a guitar support can be placed between the guitar and the left lap (the support usually attaches to the instrument's side with suction cups). (There are of course exceptions, with some performers choosing to hold the instrument another way.)
Setting up a mic to record the natural acoustic sound of the guitar strings can add percussive character when blended with the amp sound, especially if you are capturing old-school archtop sounds. For best results, the guitar needs to be isolated from the amp to prevent excessive bleed. This technique gives a good front-end attack to the sound and plenty of definition. A small condenser is the best mic for the job, and it’s worth using a high-pass filter as well.
While you don’t have to mortgage your home to buy a good guitar, price will still be a key factor in deciding which guitar to purchase. When buying for a beginner—especially younger players—you may be hesitant to spend too much without knowing if the recipient will stick with the guitar. That’s perfectly reasonable. There are guitars to fit just about every budget. Just keep in mind that the better the guitar the new player starts with, the more likely they will be to continue learning and playing. An instrument that’s hard to play or won’t stay in tune will deter even the most enthusiastic beginner.
Glen Campbell; DJ Ashba, Melissa Etheridge, Nikki Sixx, Mick Thomson; Kaki King, Steve Lukather; Marcel Dadi, Ray Davies,[30] Roy Harper,[31] James Hetfield, Josh Homme, Cyndi Lauper, John Lennon, Country Joe McDonald,John McLaughlin, Yngwie Malmsteen, Bob Marley, Ziggy Marley, Stephen Marley, Roman Miroshnichenko, Maury Muehleisen, Dave Mustaine, Vince Neil, Jimmy Page, Richard Daniel Roman, Shania Twain, Boz Scaggs, Luis Alberto Spinetta, Statler Brothers, Cat Stevens, and Aaron Tippin;[30]
This is a great local shop.  I bought a new Floyd Rose bridge for one of my electric guitars and brought it to Franklin Guitar to be installed and set up.  I got the guitar back within 2 days and it plays so well that I brought them my other guitar for a set up the next day.  Again, within 2 days I had it back and it plays exactly like the other one...awesome.  I had both guitars set up for a little more than half of what another shop quoted me just to install and set up the new bridge on the one.  High quality work at a fair price in a reasonable time...I won't go any where else to have my guitars worked on.  They also have a good inventory of guitars and amps for sale to fit any budget.
For easy, go-anywhere amplification, start out with a combo guitar amp. These all-in-one units combine the preamp, power amp and speakers into one piece, which makes them ideal for places where you want to set up and tear down in a hurry. Rehearsals and busking are easier with a combo amplifier, and they're great for small venues that don't need the power of a larger amp. The combo is your basic, high-versatility amp, and no guitarist should be without one.
You'll then learn G major and the variation you can play of this chord, where you hold the B string at the third fret, or just leave it open. The final chord you'll learn is F major. This one is tricky because its a barre chord, but there is a way of making these types of chords a little easier to learn, as shown in the video. You will also be shown the partial barre chord shape of F major, and will see how moving this shape around gives you any major chord you want to play.
If you want to take your tracks to the next level, a multi effects processor can do the trick. For a high-end example of what one of these units can do, check out the Eventide H8000FW 8-Channel Ultra-Harmonizer Effects Processor. It supports 24-bit audio and comes with an impressive 1,600 pre-set effects. Some are even pre-customized for 5.1 surround sound, so production for home theater playback is a cinch. Its smorgasbord of I/O options includes AES/EBU, ADAT, S/PDIF and FireWire with sampling up to 96kHz, so whatever you're looking to connect to the H8000FW, it's a safe bet that you can get the job done. Of course, not all of the processors here are quite as advanced. There are plenty of setups out there that just need a straightforward solution, and if that sounds like yours, don't worry: you'll find plenty of those here as well. Take the TC Electronic M350 Reverb and Effects Processor, for instance. This single-space rackmount is easy to fit into any budget, living up to TC's reputation of delivering amazing bang for your buck. It's loaded with 15 different effects plus 15 reverbs, and even includes control software for your AU/VST environment.
The body of the guitar is usually made of wood; different types of woods are used by different manufacturers, and there is ongoing debate concerning which is best. Typical woods include maple, mahogany, swamp ash and alder for quality guitars, and plywood or pine for cheaper, less durable guitars. While the type of wood used in the solid body of an electric guitar will noticeably affect the sound it produces, the quality of the sound is most affected by the pickups which convert the vibration of the strings into an electrical signal, as well as the amplifier that's used to shape and model such signal. We could go on and on dissecting the technical aspects of electric guitars, and yet never get close to that which makes that music unique: it's soul. That's something that can be clearly felt and experienced by players and listeners alike, but which all the while can hardly be put into words. Enjoy the electric guitar music loops!

The overall design of the JS11 Dinky is a streamlined and straightforward, it is basically a less contoured version of the Dinky with cost-effective parts, assembled and built overseas. But don't count it out yet because many found it to exceed their expectations in terms of looks and tone. The 25.5" scale maple neck, flat 12" radius fingerboard and 1.6875" wide nut also makes it a pleasure to play, and have made life easier for both students and experienced players alike. The high output Jackson designed humbuckers are also good enough for high gain playing, although most got great results by switching them out.
Another name that is usually associated with PRS is Carlos Santana. He has a number of guitars that bear his name, and this one is probably the most popular one. It’s affordable, sounds great and plays like a dream. After mere hours playing it, I’ve realized just how expressive you can be with it. It impressed me enough to take a high place on my list of guitars that I have to get. Needless to say, it didn’t take me long to make one a part of my collection.
The best place to start is with a small tube amp. This kind of amp is far less forgiving, leaving you nowhere to hide. It sounds counter-intuitive, I know. You’re looking for the best choice and here I am telling you one that will make things more difficult. But think of it as tough love – forcing you to confront your technique and learn the right way to play a chord or scale progression.
Effects such as chorus, phasing, flanging and pitch vibrato are created using pitch modulation and, except in the case of vibrato, the modulated sound is added back to the original to create the effect. The pitch modulation is generated by delaying the signal by just a few milliseconds, and then modulating the delay time, using a low frequency oscillator (or LFO). For vibrato, this is all that needs to be done and, because the delay time is actually very short, the effect is perceived as happening in real time. The other effects, however, generally rely on an equal balance of the dry and modulated signals to achieve the strongest effect, so it is easier when working with plug-ins to adjust the wet/dry balance using the plug-in controls, rather than adding the wet only signal via a send/return loop. As a rule, these effects aren't very processor-intensive so, if you're working with plug-ins, you can probably afford to insert as many as you need into track or bus insert points as required. Stereo versions of these plug-ins may generate different modulated delays for the left and right channels to create a more dramatic spatial effect.
A bass stack may use a single speaker cabinet (e.g., the huge 8x10" cabinets widely used by hard rock and metal bassists). The 8x10" cabinet is often provided as "backline" equipment at music festivals; this way, all the bassists from the different bands can use the same amplifier and speaker cabinet. This reduces the transition time between bands, because the roadies do not have to remove the previous band's bass stack and bring in the subsequent band's stack. Using one 8x10" as backline gear for an entire music festival also makes the transition easier for the audio engineer, because she can have an XLR cable plugged into the amp head's DI unit output (to get the bass amp's signal so that it can be mixed into the sound reinforcement system mix) and have a mic set up in front of the cabinet, to capture the amp and speaker cabinet's distinctive tone. The 8x10" cabinet is widely used by heavy metal music, hardcore punk and psychobilly bassists, as these genres use a loud onstage volume. Some metal bassists, such the bass player for death metal band Cannibal Corpse, use two 8x10" cabinets for large concerts in stadiums or outdoor festivals.
Most guitars out there usually feature a version of either one of many Gibson designs or Fender ones, but there are exceptions. Paul Reed Smith is a brand that took their own path in just about every aspect of guitar design. This made it popular with many famous guitar players, most notably Carlos Santana. The model we're looking at today is a basic version of one of their flagship guitars. The balance of performance and pure style it offers is nearly as impressive without forcing you to extend out of your monetary reach.
It's the perfect guitar ... for someone else!  So your buddy just gave you his 7-string death avenger before heading off to college cuz he knew you wanted to learn to play.  Nice, but what he did NOT know is that you hope to be the next string-bending Tele-twangin' Brad Paisley.  It ain't EVER gonna happen with you wielding the death-star, sell her to a metal head and getcha that Tele!
That protection, the MPA argued, ensures that people who create written music and related products earn a fair return for their efforts. They earn income from the sales of books, sheet music, lyric sheets, and other published materials. These individuals and companies work with the creators of music to produce well researched, accurate materials for sale to the public. The creation of these publications require substantial investments of time, materials, and fees. The free posting and distribution of TAB, lyrics, or other music notation, they argue, harms those who made those investments, and followed established business and legal procedures.

It's Mal - i posted the comment ref the muted G string on my Epi Les Paul 1960 Tribute - thanks for your response it was very good of you. I'm going to be playing (when i say playing i really mean faffing with) my guitar later so i'll have a look at the saddle, though i have rubbed my finger over it to see if there were any obvious issues which there wasn't. I have also rubbed the graphite from my clutch pencil over it when changing strings - no improvement; i'll get magnifier out and take a closer look and let you know, i may take you up on your kind offer if i'm still stumped.


Fender was started by Leo Fender in 1946 in Fullerton, CA. Leo Fender sold his company to CBS in 1965. In 1985 Fender employees purchased the company. Leo Fender founded Music Man in 1975, and later founded the G&L Musical Instruments company. Fender brands currently include brands include Fender®, Squier®, Guild®, Gretsch®, Jackson®, Charvel®, EVH®, Tacoma…
I just recently started to try to" really learn" to play guitar. I've known a few "not too difficult" songs for years. Now at 45yrs. old I bought a couple of cord books and it's bittersweet. It's such a wonderful feeling to play songs all the way to the end with a friend of mine who told me years ago that I had a good natural musical ability. I've learned more in 3 or 4 months than in 25 years. But enough about that... I was handed a jumbo GUILD from I believe around the early 70's. I've never heard anything like it. I must have one!!!

The second issue of the Les Paul guitar was introduced to the public in 1954. Called the Gibson Les Paul Custom, this entirely black guitar was dubbed the Black Beauty. The Les Paul Custom featured a mahogany top to differentiate the instrument from its Goldtop predecessor’s maple top. It also featured the new Tune-o-Matic bridge design and a pickup with an alnico-5 magnet, P-480, in the neck position. In addition, since 1957, the Custom was fitted with Gibson’s new humbucker pickups, PAF,[16] and later became available with three pickups instead of the more usual two. The three pickup model retained the standard Gibson 3-way switch so not all pickup combinations were possible. The neck and bridge-only settings were retained, but the middle switch position was set to enable the middle and bridge pickups. A common modification was to restore the standard neck/both/bridge switching combination and add a switch to enable the middle pickup on its own.[citation needed] The guitar is wired as a “normal”2 pick up Les Paul except there is a master volume , master tone, (for front and back pu) while the middle pick up has its own volume / tone. this allows the middle pu to turned out of the circuit or mixed with the other two. allowing many different tones.
The Gruhn Guitars repair shop has been world renowned for decades for its unrivaled expertise, skill, and respectful repair practices. Though our full-time staff of luthiers primarily focuses on repairing and restoring the instruments we make available for sale, beginning in 2016 we are also pleased to offer our repair services to loyal customers as an extended benefit of buying an instrument from Gruhn Guitars. Instruments purchased from Gruhn Guitars will be moved to the front of our repair queue and will be repaired at a discounted labor rate. As a sign of our appreciation for your business, Gruhn Guitars is here to help you for years to come to keep your instrument in the same prime working order as when it was listed for sale at the shop.
Same woods sounding different? OF COURSE!!! Look, I’ve been a carpenter for over 30 years and can absolutely inform you that there is a marked variation of characteristics of wood in the same species…density, tap tone, characteristics of how the individual piece reacts to being worked with tools…heck for all anybody knows internal stresses (for example as indicated by how a 12″ wide piece of wood reacts to being ripped down the center…many times both pieces end up being bowed and such) might play a big factor in how said piece of wood sounds musically…shrugs shoulders…
Valve amplification is more or less linear—meaning the parameters (amplitude, frequency, phase) of the amplified signal are proportional to the input signal—so long as the voltage of the input signal does not exceed the valve's "linear region of operation". The linear region falls between "1." the saturation region: the voltages at which plate current stops responding to positive increases in grid voltage and "2." the cutoff region: the voltages at which the charge of the grid is too negative for electrons to flow to the plate. If a valve is biased within the linear region and the input signal's voltage exceeds this region, overdrive and non-linear clipping will occur.[40][43]
There were differences between the pickups as well – the National had slanted units under enormous covers, while the Supro featured 8-string versions of the Alnico V pickups found on many Spanish-style guitars. The difference in tone proved to be minimal. The Supro has a more refined sound than its cheaper cousins with the famous string-through pickup, but it can still be raw and biting when required. Although it is a single-coil pickup, it has excellent hum rejection and sounds wonderful either overdriven or clean. The guitar has plenty of sustain and a surprising level of output, making it an excellent instrument for rock and roll as well as country music.
Bracing affects the way the guitar sounds because it changes the pitch or tune that the guitar produces out of the sound hole. Personally I think X bracing is the b est because it produces a more even and better more balance for mids and high notes and just enough bass on the E and A strings that gives a brighter more even tone. Blinded or pessed bracing gives a much deeper sound than x bracing which =less versatility but if you bought a pressed dread knot or anything else you'll still be okay just remember strings make a huge difference and running your guitar to the right amount of tone for any song will work it's just that Taylor produces the best over all guitar itself by better quality woods and they go through ver strict and rigorous testing and inspections before they are sold to retailers and customers. Higher grade parts attention to detail and style of music versatility is why one guitar can cost 3 times as much. Most companies like Taylor is know give warranties or $ back
During Michael Laskow's 20-year tenure as an engineer/producer, he worked with Crosby, Stills, Nash and Young, Eric Clapton, Cheap Trick and countless others. He continues to write articles for magazines like Recording and Electronic Musician. He's also the founder of TAXI, an independent A&R company that links record labels with unsigned artists and songwriters.
Norma branded guitars all came from the import/distribution company Strum and Drum located in Wheeling, Illinois.  Lots of people think Norma came from Norma Jean (Marilyn Monroe), but actually the Norma name came from the owner of the company, Norman Sackheim!  Norman and his son Ron began to import Japanese guitars around 1965, and continued into the mid 70s.  Initially all Norma guitars were made at the Tombo factory in Japan, but by 67 there were at least 8 different suppliers of Norma guitars!Build quality and construction really varied greatly with Norma guitars, but Norman and Ron did have a good eye for unique designs and many Norma guitars featured some of the coolest shapes of the 60s!  Just like this 4 pickup monster!  What I always liked about Norma guitars were the cool features like neat inlays and interesting pickups.  These darn things just had style!While I was in Japan in 2013, I met with the Japanese buyer of Norma guitars.  A close friend of the Sackheims, this gentleman travelled Japan during the 60s and searched out cool guitars to supply to Strum and Drum.  It was a unique arrangement, and it was simply fascinating to listen about the old days of Japanese guitar production.  When you peruse Norma catalogs, you’ll often see models come and go quickly.  And there were always lots to choose from, year to year.
Here we ( SOLD ) are very proud to offer a USA built Martin Acoustic electric the model # JC-16RGTe.... More info soon to come and more pics as well... near mint condition like new! Everyone from Eric Clapton to Sting to Johnny Lang has played a Martin guitar, and professionals and amateurs alike know the bright sparkle and deep, resonant tone that Martin guitars have become famous for, from the most high end acoustics to the Backpacker. Carefully hand-selected tonewoods, master craftsmanship and beautiful finishes and styles make Martin acoustics a class all their own, and must be played to be believed. Martin sets the standard for acoustic guitars, and since 1833 has been a leader in guitar innovation and craftsmanship. The following info is from Martin. Martin JC16RGTE Features: * CONSTRUCTION: 1 Style; Ply Blocks; Mortise/Tenon Neck Joint * BODY SIZE: D-14 Fret CUTAWAY * TOP: Solid Sitka Spruce * ROSETTE: Bold Herringbone * TOP BRACING PATTERN: D1 Hybrid * TOP BRACES: 1 Style/Scalloped * BACK MATERIAL: Solid East Indian Rosewood * SIDE MATERIAL: Solid East Indian Rosewood * ENDPIECE: White Boltaron® * ENDPIECE INLAY: Black/White Boltaron® * BINDING: White Boltaron® * TOP INLAY STYLE: Multiple Black/White * NECK MATERIAL: Solid Spanish Cedar * NECK SHAPE: Modified Low Oval * NUT MATERIAL: White Corian® * HEADSTOCK: Solid/6 String No Diamond/Standard Taper * HEADPLATE: Solid East Indian Rosewood/ Raised Gold Foil Logo * HEELCAP: Solid East Indian Rosewood * FINGERBOARD MATERIAL: Black Micarta® * SCALE LENGTH: 25.4" * # OF FRETS CLEAR: 14 * # OF FRETS TOTAL: 20 * FINGERBOARD WIDTH AT NUT: 1 11/16" * FINGERBOARD WIDTH AT 12TH FRET: 2 1/8" * FINGERBOARD POSITION INLAYS: 28 Style * FINGERBOARD BINDING: White Boltaron® * FINISH BACK & SIDES: Semi Gloss/ Dark Filler * FINISH TOP: Polished Gloss * FINISH NECK: Semi Gloss/ Dark Mahogany Stain/ Dark Filler * BRIDGE MATERIAL: Black Micarta * BRIDGE STYLE: 1 Style Belly * BRIDGE STRING SPACING: 2 1/8" * SADDLE: 16" Radius/Compensated/White Micarta® * TUNING MACHINES: Chrome w/ Small Knobs * RECOMMENDED STRINGS: Martin MSP 4100 Light Phosphor Bronze * BRIDGE & END PINS: White w/ Black Dots * PICKGUARD: I-02 Tortoise Color * ELECTRONICS: Fishman® Prefix Premium Stereo Onboard Blender .
Based on Mesa's flagship Mark V, the Mark Five: 25 head is small, perfectly formed and typical of Mesa's superlative design and attention to detail. Two independent channels, each with three very different voice presets, combine with Mesa's iconic five-band graphic EQ for a choice of 12 sounds. You can footswitch between the channels, with the graphic on or off for quasi four-channel operation and preset 25 or 10 watts per channel. One of the best features lives on the back panel: a CabClone speaker-emulated direct output, with a speaker defeat for silent recording or practice, using the built-in headphone socket. Despite the Mark Five: 25's long feature list, it's very easy to use and its tones are sensational. The rhythm channel covers the shimmering clean tones of the modern Boogie and the fatter 'blackface'-inspired midrange of the fabled Mark I, while the Mark V crunch voice is so deep and three-dimensional you could record an entire album with it. The lead channel is equally inspiring, with a perfect rendition of the Mark IIC's overdrive tone (arguably the most coveted Boogie sound), along with more modern distortion effects that sound unbelievably good when tweaked with the graphic. The Mark Five: 25 is one of the best small Boogies we've ever heard, which means it's one of the best small amps there is.

Pete Townshend turned his guitar into a machine gun. That was the actual sound he went after, slamming his guitars into speaker cabinets and toggling the pickup-selector switch violently. “To me the guitar was a symbol,” explained the Who’s lead guitarist. “It was a metaphor for a machine gun. And the only thing you could do with a machine gun in the 60s was break it across your legs. That’s what I did.” You can hear these specific sonic strategies on songs like My Generation and Anyway, Anyhow, Anywhere.
We will use the remaining pole to switch tone pots. Typical strat wiring has two tone controls – one for middle and one for neck pickup. We want to switch neck/middle tone control on when neck/middle pickup is on. To do this, common terminal of the second pole is connected to the common terminal on the first pole (pickup output) and neck and middle terminals of the second pole are connected to their respective pots. When neck pickup is on, the second pole will switch the output to the neck tone control as intended. What happens in position 4 (both neck and middle pickups on)? Both pots will be switched on and will be in parallel. Moving any tone pot would change the overall resistance to the tone cap and change the tone. The result is below:
Many guitar and bass bodies are made from Mahogany. There are 49 types of Mahogany, but many are practically extinct because of the wood’s popularity for furniture and musical instruments, and the types used today are not the same as the Mahogany used in guitars in the 1940s or 1950s. Mahogany gives a warm timbre with a lot of bottom end. Les Paul type guitars often combine a mahogany body with a maple top for a total that is balanced overall.
For every guitarist who’s dreamt of combining the biting twang of a Telecaster® with the sleek, ergonomic contours of a Strat, we created this limited-edition guitar: The Whiteguard Strat. Tele hardware, electronics and playing feel? Check. Ash Strat body with lacquer finish and custom-shaped white pickguard? Check. The unique style and sound you can only get from Fender? You better believe that’s a check.
On September 6, 2018, the company announced that a global settlement has been reached with respect to the company’s reorganization plan upon emergence from Chapter 11. Under the plan, the company will be focused on its core musical instruments business with "essentially no debt." Current Chairman and CEO Henry Juszkiewicz will step down as CEO and assume the role of consultant. With immediate effect, Brian J. Fox, the company’s CRO, will oversee daily operations until a new CEO is appointed.[59]
There is one musical virtuoso whom I would added to this list, if for no other reason then the fact that the 2nd guitarist on the list thru his comment, seemed to hand the title as “greatest guitatist on earth” to this guy. This same individual has often been compared to the one who holds the crown- Jimi. And yet, arguably should not be in this list due to the fact that he was much more than a Master of the guitar, he mastered vurtually over 30 other instruments he played, sold almost Every concert he performed world wide, and… Read more »
We gave our electro-acoustic chart a big refresh to keep it relevant for early 2018, by replacing a few older guitars with some excellent upgraded models. Guitars such as the Epiphone PR-4E and Mitchell MX400 were removed, and in came the exquisite Yamaha A Series A3M, the new PRS SE A50E, the cool Fender Sonoran SCE, and two solid budget models, the Kona K2 and Yamaha’s APX500III.

Boss is an effects legend, but thanks to the digital expertise of parent company Roland, the brand now also has an amp that promises organic, valve-like tones at an impressively low price. It does this by using the same Tube Logic technology employed in last year’s 150-watt Waza Craft head, and other Roland amps. The K100 doesn’t invite direct comparison with specific amp brands and models. Instead, there are five generic voices: Acoustic, Clean, Crunch, Lead and Brown. You can pre-load 15 different effects types into the amp, with 55 to currently choose from when you link the Katana to the Boss Tone Studio application. The Katana may look plain, but its tones are truly exceptional. The Crunch voice is responsive and dynamic, while the Brown solo sound is as good as many USA valve-powered competitors. Start using the Tone Studio editor and the Katana’s edge becomes sharper still, with different effects chain presets and assignable control parameters.


(48 Contiguous U.S. States) Free Free Shipping With Backstage Pass 92118 2-Day Standard Ground {savingIsUpTo=false, MSRP=248.0, listPriceRange=false, isFreeShipping=true, download=false, isPriceDrop=false, salePriceRange=false, YourSaving=0.0, productId=site1prodJ40301, MSRPRange=false, enablePDPColorOption=true, showBrandNameWithProduct=true, usedAmount=131.12, restockStartAmount=null, listPrice=149.0, priceVisibility=1, usedCount=1, salePrice=149.0, isOnSale=false, showMSRP=true, restockCount=0}
Pitch Bend/Shifting: From a simple octave above the note you’re playing or at intervals in between, a pitch shifter effects pedal will change the pitch of your note or chord. More sophisticated pitch shifters create two or more harmony notes so you can accompany your root note for a fuller sound. Some simulate a chorus effect by providing minute shifts in pitch.
I wish I had a cool story to attach to this guitar, but really this one is a history lesson regarding the development of Japanese guitar manufacturing.  Plus, it’s an example of some rare component combinations (like the pickups) that make guitars like these worth buying.  THEY’RE SO CHEAP!!  Hell, buy one of these for $200, send it to Dano and sink another $100 into it, and you’ll have yourself one hell of a player!  It’s like recycling, dude.
Guitar-Sunbeam : Precisely transmits the eternal electric guitar, ideally suited for modern production. It combines an extensive library of strum patterns, brute force, arpeggios and real riffs with real-time performance monitoring. An innovative playback engine allows you to create an almost infinite number of variations of chords and you get convincing, musical results.
The electronic transistor finally made it possible to cram the aural creativity[when defined as?] of the recording studio into small, highly portable stompbox units.[citation needed] Transistors replaced vacuum tubes, allowing for much more compact formats and greater stability.[citation needed] The first transistorized guitar effect was the 1962 Maestro Fuzz Tone pedal, which became a sensation after its use in the 1965 Rolling Stones hit "(I Can't Get No) Satisfaction".[41][42]
But in general, there's nothing wrong with Decca electric guitars, especially for indie musicians today who are looking for a vintage guitar with some character to it. Since most vintage guitar fans have seen every model that Gibson, Fender, et al, have ever made, many of the Japanese guitars of the '60s have a fresh look that stands out from the crowds. In 20 years, the M-i-J electric guitars of the '60s are going to be worth 4 or 5 times what they sell for now, and smart collectors who either can't afford Fenders, Gibsons and their ilk from that period, or who are interested in something more unusual, are already snapping them up.
• Do the Right String: Some instructional guides advise beginning players to try ball-end nylon strings because they are easier on the fingers and are more bendable than metal, but steel string guitars are called “steel string guitars” because that’s what they require. Nylon strings lack the tension needed to keep steel strings guitars at their peak, which means warping, bridge damage and other issues can occur. Likewise, steel strings on a nylon string classical guitar will warp its neck with frightening speed.

The material in the neck and fretboard also matters. Some guitars have both neck and fretboard in maple, and they will typically have a bright and open sound. Rosewood has traditionally been used for fretboards, usually combined with a maple neck, because it is a hardy and oily wood that can stand up to extensive human contact. Rosewood will give a darker tone than maple alone.
Wow! I don't even know where to begin... I am using this processor with my new Cecilio electric violin. I learned and trained on classical violin, acoustic, reading sheet music, etc, so I'm pretty new at now playing an electric one hooked up to an amplifier, and even newer at using a pedal/processor. Upon first assembly, I found that many of these effects will probably not be used in the music that I play (worship & praise - old school & contemporary), but others will be very useful to bring a new sound to old songs. Also, some of the effects sound very similar to one another. I haven't yet figured out and tried to edit and save any effects to my liking, so I can't really say how well the MG-100 does in that area. But I must say that I am absolutely in love with the drum machine ... full review
Sometimes a pitch shifter will retain the original signal while adding in the new shifted pitch.  The new shifted note can be set at a given intervallic distance from the original and will automatically harmonize any given series of notes or melody.  In short, it will harmonize the guitar by duplicating the melody at a 3rd, 5th, or whatever interval you define.
Some effects produced dramatically weird sounds that were largely impossible to pull off. The peculiar 1948 DeArmond Trem-Trol (used extensively by rock-and-roll pioneer Bo Diddley) altered the volume of the guitar signal by exposing the connecting pin to a brass-and-glass canister half-filled with shaking, water-based electrolytic “Hydro-fluid.” The shaking—and often leaky—fluid washed over the pin and would bend the signal’s volume, causing an oscillating, watery tone. In the words of Chris Gray, one of its few remaining owners, “This is not a subtle effect—it adds all its personality to your sound whether you’re ready for it or not.”
Over the past three years, Gibson’s annual revenue has fallen from $2.1 billion to $1.7 billion, according to data gathered by Music Trades magazine. The company’s 2014 purchase of Philips’s audio division for $135 million led to debt — how much, the company won’t say — and a Moody’s downgrading last year. Fender, which had to abandon a public offering in 2012, has fallen from $675 million in revenue to $545 million. It has cut its debt in recent years, but it remains at $100 million.
There’s a 10-watt, eight-ohm Fender Frontman 10G amplifier with a six-inch Fender design speaker that will give you plenty of amplification if you’re learning in your bedroom or apartment. There’s even a two-band EQ giving you more tonal control and a silver-face mesh grill paying homage to Fender’s classic vintage amps. They’ve also thrown in an instrument cable (for connecting your guitar up to your amp), an electronic tuner for keeping things sounding right, a gig bag, a guitar strap, a pick sampler (so you can audition different thicknesses of pick to determine the best for your playing style), plus an instructional DVD to make sure you start your learning off on the right foot.

The distortion effect was first created back in the 1950's by overdriving the tubes of a guitar amplifier, usually by turning an amp all the way up. This caused the guitar signal to distort or "break up." While this effect was originally considered bad by amp manufactures, early rock players found it exciting since it provided a new tone for the electric guitar's sonic palette. A tone that had an edge and power that fit perfectly with the new type of rock playing that appeared in the 1960's. As amplifier manufacturers embraced distortion, they began adding more gain to their amps, which resulted in more distortion and lead to styles such as metal and shredding. Pedals have been created to simulate all these types of distortion.

The PRS S2 Custom 24 is a stripped down version of the expensive yet sought after PRS Custom 24 guitar, and because of its accessibility, it helped put the Custom 24 design into the hands of more players. What's impressive about the S2 Custom 24 is how it retains the same attention to detail and quality as PRS' more expensive guitars, making it a viable instrument even for those who can afford more expensive alternatives.

Aside from the stereo effect of doubling up the same part and panning it to opposite ends of the stereo spectrum, some guitarists use stereo rigs in conjunction with stereo effects. Traditionally, this involves using two amp cabinets, although single cabs that operate in stereo are available. To achieve a good, even stereo image, it’s best to mic each cab identically, ideally with the same type of mic. Invert the polarity of one of the channels to avoid any out-of-phase issues, and pan them hard left and right. Stereo effects such as reverb, delay and room ambience, can be added to mono guitar signals at the mixing stage.


If you want to spring for a pedalboard and processor combo that offers multiple effects in one unit, you might want to check out something like the HeadRush Pedalboard with Guitar Amplifier and Effects Modeling Processor. It offers 33 amplifier models, 15 cabinet models, 10 microphone models, 42 effects, and includes an expression pedal, 7" touchscreen, 12 foot switches with OLED Screens, and more.
Since you're a beginner, lighter strings are probably going to be easier for you to play until you get your fretting hand built up with permanent callouses and finger strength. I would advise buying 9-42 gauge strings even if that's not what your guitar came with originally - if it had 10's on it from the factory, the 9's will feel slinkier and more forgiving on your hands.
So, which are the best budget electrics guitars available today? We've gathered a selection of the electric guitars that we reckon offer the best bang for the buck in the sub-$/£500 market. You may recognise some of the perennial budget classics (hello - again - to the trusty Yamaha Pacifica), but there's a raft of high-scoring options out there for the more adventurous.
Overdriven speakers create one of the most desirable distortion characteristics: crunch. The best way to test for this is to dial in a clean setting and turn the volume way up. Low-wattage speakers break up at lower volumes, but they have a tendency to turn to mush at excessive volume levels; high-wattage speakers may not break up at all. Choose a speaker that sounds lively, defined and harmonically rich at volume and distortion levels you’ll normally play at.

“The California Series captures the true meaning of a Fender acoustic guitar,” said Billy Martinez, VP Category Manager – Acoustics and Squier Divisions. “From the iconic 6-inline Stratocaster headstock to the original Fender body shapes and organic styling, everything about these guitars is uniquely Fender making them the ultimate tools for artistic creative expression. Whether you’re at the beach or rocking out with a band on stage, we’re offering players of all levels a chance to express their own creative style, standing out in the crowd with the bright colors and energy these guitars give off.

For the most part, you might want to get a preamp that has at least some type of EQ on it. Tone shaping on an acoustic electric guitar can really give you an edge or at least a semblance of control before the sound guy butchers it during your gig, although you can do this with an effects pedal. Even though this is something that takes the time to learn, it's better to have the option readily available when you decide to step up to that level.

In late 1929, Martin built a prototype batch of six OM guitars. The very first of these had pyramid bridges and no pickguard. Martin soon realized that with the vigorous strumming required in a band setting, a pickguard would be required. Hence all OMs after the prototype batch had a small teardrop-shaped pickguard. The new OMs were not highly sucessful. They sold, but not as well as Martin had hoped. In 1933 the OM designation was dropped and was now called the "000" model. But infact the 1933 "000" models were the same as the 1933 "OM" models, retaining the OM body style and 14 fret neck. Then in 1934 the standard 000 models were modified to the shorter 24.9" scale (for unknown reasons, as the 12 fret 000 body had a 25.6" scale length its inception in 1902 to its demise in 1931). Yet the OM's longer scale was a major factor in the OM's tone. The strings on an OM must be tuned to a higher tension to get concert pitch. This extra tension translates into more drive on the top, hence providing more volume and tone. The OM's scalloped braces and a small maple bridgeplate give the OM a great sound. Although these features were common to other Martin models of the time, the OM's top brace under the fingerboard was missing. This design is unique to OMs making the top very lightly braced. This does lead to some problems with cracks in the upper bout along the side of the fingerboard, but it also contributes to the great sound of the OM models.


Electric guitars and guitar equipment - want something new? Shop online and in-store for your new guitar setup. Pick from solid body, semi-acoustic, and hollow body styles to get your ideal electric guitar. We stock all the major guitar brands like Fender, Gibson, and Ibanez. Alongside electric guitars, you'll find amps and pedals from Marshall, Vox, and Orange.
{ "thumbImageID": "German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Natural-Satin/K36144000001000", "defaultDisplayName": "Warwick German Pro Series Corvette $$ 4-String Electric Bass Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Natural Satin", "sku": "sku:site51500000072278", "price": "1,949.99", "regularPrice": "1,949.99", "msrpPrice": "2,549.99", "priceVisibility": "1", "skuUrl": "/Warwick/German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Natural-Satin-1500000072278.gc", "skuImageId": "German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Natural-Satin/K36144000001000", "brandName": "Warwick", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Natural-Satin/K36144000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Burgundy Red", "sku": "sku:site51500000138040", "price": "1,899.95", "regularPrice": "1,899.95", "msrpPrice": "2,649.99", "priceVisibility": "1", "skuUrl": "/Warwick/German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Burgundy-Red-1500000138040.gc", "skuImageId": "German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Burgundy-Red/K36144000002000", "brandName": "Warwick", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/German-Pro-Series-Corvette-4-String-Electric-Bass-Guitar-Burgundy-Red/K36144000002000-00-60x60.jpg", "imgAlt": "" } ] }
In the guitar’s electronics, the potentiometer and capacitor form a path to ground. The capacitor presents lower impedance to higher frequencies, and vice-versa, so the tone control works by “throwing away” high frequencies. How much of the highs get thrown away is determined by the tone potentiometer, which presents an equal resistance to all frequencies. As you turn down the tone, you decrease the resistance presented by the pot. Low frequencies still find this path to ground to be a difficult one (high-impedance) because of the capacitor, but high frequencies see an easier path than the one into the amplifier (which traditionally has a fairly high impedance load in the transistors of the “pre-gain” stage, around 1Megaohm), and to they take the easier path, reducing the presence of high frequencies that are amplified and output as sound.
Electric guitars vary by type. Some are designed for beginners, while others are customized for professional guitar players. Most of the major electric guitar brands are available in a variety of different styles, each designed to best suit a customers' specific playing needs. The most popular electric guitars have great rock sounds and the best bodies. On electric guitars, strings affect the sounds too. Ease and sound are certainly big factors to consider when choosing a new electric guitar.
When using multiple microphones, always remember to check for phase cancellation, and keep in mind that a 2-8kHz boost is probably all that's necessary at mixdown for enhanced electric guitar presence within a track. A small amount of delay (1ms = 12") on an ambient mic track will increase the perceived ambient distance of the microphone without actually moving the mic. This trick works well when blending close and ambient microphone tracks during recording or mixing.
they're both excellent guitars, and for jazz-only, and a little more money, the eastman was a little better. it had a bit more acoustic volume and sounded really killer plugged in. but, the godin is the one i ended up keeping. really, really versatile guitar. the tone knob has a wide range of usable tones. really a very articulate sounding guitar plugged in, especially with the tone a little more open. i play a lot of straight ahead jazz on it, and am very happy with the sound. i have always played it with 12 gague strings on it. again, it's not terribly loud unplugged, but the sound is great, and this is designed primarily to be used plugged in.
The Ibanez pickup sound is great and solidly diverse throughout the 5-options, providing lots of versatility for a variety of different music styles.The tuning is nice and extremely stable, and you can even dive-bomb on the whammy without throwing it out of whack. The frets are perfect, and the action is almost perfect, with that quality feel to it.
I have 2 Kent guitars. One like a Strat and one 12 string hollow body. I know they were made in the 60s and were distributed by Kent Musical Products. Address:5 Union Square, New York. 10003. And they were a subsidiary of Buegeleisen & Jacobson, Inc. Any further info on these would be appreciated. Most sold in the price range of 100 dollars and up.
SOLD OUT ! We are VERY pleased to present a very special example Alvarez Yairi Classical guitar . The condition of this high end instrument is excellent plus and this guitar is simply wonderful. This is hand built example by The Kazou Yairi himself, Japanese Master Luthier. For those of you not familiar with the Premier Japanese Master Luthier Kazou Yairi and his masterfuly built instruments you may enjoy this vidio introduction to YAIRI GUITARS http://www.youtube.com/watch?v=NPRyLPouYZM The model is CY116 and is a very high-end professional guitar and is in excellent Plus condition. Only the highest grade woods used as you can see ...choice AAA Flamed-Quilted and is 3-dimensional depth is a work of art as you can see by the pictures. This guitar plays and sound AMAZING and is truly inspirational. This guitar shows very little fret wear. There are just a few minor nicks or scratches which is normal wear for a guitar of this vintage that has been lovingly played. This one is a one owner adult owned guitar and comes with its high quality custom hard shell case too. General Specs: Alvarez Yairi CY116 Classical Acoustic Guitar The CY116's Solid Cedar Top is adorned by an elaborate wooden mosaic rosette. Burled Maple Back/Sides give this classical amazing clarity and warmth like the fiery Andalusian plains that inspired the music that this guitar was born to perform. With room-filling projection, the CY116 is a guaranteed conversation starter. You hear it in the elegant pacing of a classical air. You see it in the vivid charm of a folk dance. Specs: Burled Mahogany Back/Sides Solid Cedar Top Mahogany Neck Ebony Fingerboard Scale: 25 1/2" (650mm) Width at Nut: 2" (51mm) Rosewood Bridge Ivory Body Binding Wooden Mosaic Rosette Gold Vintage Open-Style Tuning Machines .
Morning everyone, well it is here in UK anyway. Who can help with my find. It's a Dia Hummingbird labelled F 315 but no serial number. So from what I can find Dia was a brand used by Matsumoku but I can only see electrics under Dia brand when I search. However it looks identical to a Aria F315 Hummingbird on eBay USA at present, and identical to an Aria Pro II from the 1976 catalogue but labelled W 30 model I believe. I won't put a link on here in case I'm breaking rules. It has that weird aluminium compensated bridge and seriously, this one looks brand new with two tiny dings that would make it a second or an ex-demo if it was on sale. Action at low E 12th is about 2.7mm and about 1.8 at high e. It's in such good condition I began to question if in fact it is a 'knock off of a knock off' though why anyone would think that would work I can't guess. It is very very playable, and at first I wasn't keen on the tone though sustain is great (despite bridge) but I changed to heavier strings (13) with much improvement. I'm seeing a luthier friend next week who is finishing off work on a brilliant Terada FW 613 (D18 clone if you like), but I'm wondering whether to get him to replace the whole alloy bridge. I can do a couple of pics if anyone is interested. Any help in identification of maybe year (guessing 1976) and origin greatly appreciated. I think it's a keeper, but should I change that bridge ? Has anyone done similar on one of these compensated aluminium designs and what were results. Many thanks.
Nobody ever forgets their first guitar. It's an exciting moment that signifies the beginning of a life that's filled with musical enjoyment. For this reason, you need to be sure that the guitar you purchase is more than worthy of making your talents fully realized. And thankfully, there is no shortage of astounding guitar value packages to choose from, right here.
{savingPercent=0.00, isPreOrder=false, pimStatus=R1, visibilitySalePrice=9.99, typeCondition=New, statusText=In stock, isPriceDrop=false, displaySku=451058000001000, invMsgBackOrdered=false, skuPriceVisibility=1, stickerUrlLink=null, kitCarouselSkuIds=1500000222576,1363016749098,1368456537505,1300744185161,1377190992159,1500000250930,1368456537510,1363811587202,1500000222578,1500000154196, stickerURL=null, availableDate=Wed Feb 27 04:20:22 PST 2019, invMsgAvailability=, serialized=false, listPrice=9.99, isShipsInternational=true, name=Black, invMsgBuyToDemand=false, partNumber=SSG-303 BK-MG, MSRP=24.99, inventoryStatus=1000, newPrice=9.99, condition=New, status=instock, stickerClass=null, stickerText=Top Seller, invMsgOverSized=false, invMsgDetail=, YourSaving=0.0, MSRPRange=false, invMsgPreOrder=false, invMsgVendorDropShip=false, availableInStoreOnly=false, prop65=WARNING: This product can expose you to chemicals including Vinyl chloride, which is known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov., salePrice=9.99, warranty=false, displayId=1274228076940, stickerDesc=Top Seller, isOnSale=false} 9.99 USD

My father's Yamaha was bought in the 90's, and was the first guitar steel-string I ever played as a kid. (If you were curious its equivalent to today's model would be the LS6 ARE). To this day I still find myself going back to it. It's little quirks makes it really special, even though I have martins and taylors and even gibsons. There's little nicks and chips in the paint in some places, which really shows it's history. It's also stood the test of time. It still plays great after almost 30 years of being lugged around from place to place, dropped, hit against walls, etc. It's just simply great. - zabathy1

EMG DG20 David Gilmour Wired Pickguard   New from$329.00In Stockor 8 payments of $41.13 FREE 2-DAY SHIPPING Seymour Duncan SH4 JB Humbucker Pickup   New from$79.00In Stockor 4 payments of $19.75 FREE 2-DAY SHIPPING Gibson '57 Classic Humbucker Pickup   New from$164.99In Stockor 4 payments of $41.25 FREE 2-DAY SHIPPING EMG JH Set Custom James Hetfield Signature Pickup Set   New from$249.00In Stockor 6 payments of $41.50 FREE 2-DAY SHIPPING See All Electric Guitar Pickups
×