Body:  Soundboard:  two-piece spruce: medium grain broadening toward the flanks. Back: two-piece spruce: fine grain on bass side broadening to medium at the flank, wide grain on treble side; slightly arched; two f-holes; recessed 11 mm from edge of ribs. Ribs: 7-ply plywood, the outer layer birch, the inner layers mahogany, the outer veneer layer grain running perpendicular to plane of top and back; panel on bass side with nickel-plated steel plug; slides out for access to pickup unit. Head: mahogany veneered with white celluloid on both faces. Neck: mahogany; integral with head; rosewood stripe.
Description: Body: Basswood (Tilia, Linden, Lime) - Neck Attachment: Bolt - Neck Wood: Maple & Walnut - Neck Construction: 5 Piece - Nut Width: 55mm - Fingerboard: Rosewood - Frets: Jumbo - # of Strings: 8 - Scale Length: 27" (69cm) - Headstock: 4+4 - Bridge: Fixed - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: IBZ-8 - Pickup Configuration: H-H - String Instrument Finish: Black, White
First, Steel String sounds heavenly, and I always love it when my mouth drops the first time I hear a hyper-realistic sounding VST. Steel String has done this completely, in fact, the only time I was ever pulled out from its hyper-realism was on the fret noise that recreates the articulation of finger sliding across the strings when changing positions.

Far as commercial recordings go, the oldest recording seems to be by the Hawaiian group Noelani Hawaiian Orchestra in 1933, which did four songs featuring the electric lap steel recorded on Victor records. However, the guitarist is unknown. Bob Dunn recorded electric lap steel in 1935, as part of the country swing group Milton Brown and His Musical Brownies. George Barnes recorded "Sweetheart Land" and "It's a Low-Down Dirty Shame" with Big Bill Broonzy in early 1938, followed a couple weeks later by  Eddie Durham with the Kansas City Five. Barnes played conventional guitar, not lap steel, so that's the first recording of a "conventional" electric guitar performance.

The reason why we love this guitar so much is that the top is made from koa wood. What is koa? It’s a Hawaiian wood that has a very special look to it, with an unusual grain pattern. When you have a guitar top made from koa like this, it just looks very organic and natural, so if you don’t like the plastic-fantastic style, then this is the best way to go!

Classic 000 Martin copy by the great Yamaha Nippon Gakki factory in Japan, Here is a fine example , no structural issues no cracks and neck is excellent and plays with ease because it has great action, intonation is 100%, beautiful patina of a true vintage 40+ year old with great workmanship and materials this example has stood the test of time like few have its not new or mint of course it has been played but not abused and taken care of and maintained and sounds better than new with its well aged TONE WOODS these are 40+ years old but when made the woods were known to have been aged over 20 years then so this doesn't compare to a new Yamaha all of those factors make this a rare survivor. Fun to play because it sounds so good and is easy to play. Pics soon to come. Questions for Joe or ready to buy email me at: .

Add bite or presence by boosting between 2kHz and 6kHz, depending on the tone you're after. Little over 4-5kHz is produced by a guitar speaker, though going for a brighter DI'd clean sound is quite legitimate for artistic reasons. Similar-sounding electric guitars that may be conflicting within a mix can be separated to a limited extent by adding bite at different frequencies, though choosing two different-sounding guitars and/or amp sounds and examining the arrangement carefully usually works better. As a rule, single-coil guitars are best for cutting through a busy mix without taking up too much space, while humbucking pickups create a thicker sound which may be beneficial in recordings where there is only one guitar part.

For die-hard metal players looking for best electric guitar brands, Dean is another famous name you wish to check. The iconic ML design has become a signature instrument for rock because of Damageplan and Darrel Abbott of Pantera (late). In the ’90s, ML was revived by Dime, and then Dean stretched out the idea while sharpening the designs of it with a modern touch.

Unlike the piano, the guitar has the same notes on different strings. Consequently, guitar players often double notes in chord, so increasing the volume of sound. Doubled notes also changes the chordal timbre: Having different "string widths, tensions and tunings, the doubled notes reinforce each other, like the doubled strings of a twelve-string guitar add chorusing and depth".[38] Notes can be doubled at identical pitches or in different octaves. For triadic chords, doubling the third interval, which is either a major third or a minor third, clarifies whether the chord is major or minor.[39]

{"eVar4":"shop: pro audio","eVar5":"shop: pro audio: signal processors","pageName":"[gc] shop: pro audio: signal processors: multi effects processors","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: pro audio: signal processors","prop1":"[gc] shop: pro audio","evar51":"default: united states","prop10":"category","prop11":"multi effects processors","prop5":"[gc] shop: pro audio: signal processors: multi effects processors","prop6":"[gc] shop: pro audio: signal processors: multi effects processors","prop3":"[gc] shop: pro audio: signal processors: multi effects processors","prop4":"[gc] shop: pro audio: signal processors: multi effects processors","channel":"[gc] shop","linkInternalFilters":"javascript:,","prop7":"[gc] sub category2"}
This final trick is pretty cool for live use because these effects are very efficient, which means that you can have several tracks of 'racks' without straining your CPU. Go to the Mixer tab at File/Preferences/Project, and check 'Enable Solo on Selected Track'. Solo a track, and now all you need to do to call up a new sound is select a track, and the Solo will 'move' to that track. The change from one sound to another is instantaneous. Now it's time to amaze your audience!    
When it comes to guitar amplifiers, especially the ones that we love here at PMT, “cheap” doesn’t mean poor quality! Thanks to huge leaps in manufacturing processes, stringent quality control and the fact brands really care about the products they create, you can spend far less on an amplifier and musical instrument these days and still get a fantastic, highly playable and superb quality option for your needs.
The palm mute is a playing technique for guitar and bass guitar, executed by placing the side of the picking hand below the little finger across the strings to be plucked, very close to the bridge, and then plucking the strings while the damping is in effect. This produces a muted sound. It was popularized by Black Sabbath in the song "Paranoid". - winner333
The questions I get asked in response to people reading my stuff on guitar wiring often relate to the 5-way pickup selector switch so I thought I’d write a brief explanation of how it works. Understanding how the 5-way switch on your guitar works is key to successful guitar wiring. Knowing what goes on inside the switch may sound like a simple, maybe trivial, detail but it’s something we all need to understand and it’s not as easy as it first seems.
Repairing pickups. You do not have the option of repairing and salvaging the pickup beyond re soldering the coil wire. If you do this be aware you are not repairing but instead customizing. However, to repair or restore pickups start by re-magnetize the coil magnets using strong earth magnets. If you need to re-solder the coil wire, unwind the pickup tape and properly re-solder in the wire appropriately.

Hoshino Gakki also had semi acoustic, nylon and steel stringed acoustic guitars manufactured under the Ibanez name. Most Ibanez guitars were made for Hoshino Gakki by the FujiGen guitar factory in Japan up until the mid to late 1980s and from then on Ibanez guitars have also been made in other Asian countries such as Korea, China and Indonesia. During the early 1980s the FujiGen guitar factory also produced most of the Roland guitar synthesizers, including the Stratocaster-style Roland G-505, the twin-humbucker Roland G-202 and the Ibanez X-ING IMG-2010.

I have a Gemtone guitar tube amp that was made in Canada in early 70's I think. This is the only Gemtone I have ever seen and the only information I could find out about it (but not verify) is that it was a sub-company of Regal Instruments. I would love to find some more info about this amp but have nearly given up after several years of searching. Sorry its not really an answer but my hope is to fire up the thread again so someone with more concrete info can chime in.

What you need is some basic knowledge about the physics of audio (most of which you can learn by dropping a pebble in a puddle of water), and some pretty basic and inexpensive equipment. This is especially true for recording the electric guitar. Trust me--if it were brain surgery, I would have become a brain surgeon and made my mother a much happier woman. And while I have the opportunity . . . for all you kids who want to grow up to be recording engineers--don't do it. Become brain surgeons. They make a lot more money, drive nicer cars, and never have to worry about where their next gig is coming from.
Covers all the material needed for the RGT Grade One electric guitar examination, enabling you to gain an internationally recognised qualification. The book should help you to develop all aspects of guitar playing, increase your knowledge of specialist electric guitar techniques, understand the music theory that relates to electric guitar playing and achieve your full potential as a guitarist.
First of all, the pickup configuration is getting into the heavy metal side of things and, like the two previous recommendations, it offers a great introduction into changing your sounds on the fly. You know that expert players are constantly stomping on effects pedals to change the tone of the guitar, but they’re also tweaking the pickup positions, tones and volumes to create unique sounds, too.

While it is well loved for its HD amp models, it also packs quite a lot of effects (over 100!), applying the same HD modeling technology on actual stompboxes to get them to sound as close to the real thing as possible. The amp modeling and effects section together allow for a wide variety of tones, while the deep controls that you have over each amp and effect parameter allows for even more in-between tones, so you can craft your very own sound. The LED rings add to the unit's overall eye candy and improve the already intuitive interface of the unit. It also houses extensive input and output options, including having its very own mic preamp, so you can use it for a variety of instruments and even vocals. Other features include built-in 48-second looping, tuning and compatibility with Line 6' modeling instrument (Variax) and amps.
Curiously, Les Paul also contributed to recording... along with building his own recording studio at his home, he built his own disc cutting system, and did multitrack recording on acetate discs... recording on a disc, then overdubbing himself and that original disc playing onto another disc, and so on. He later worked with Ampex on multitrack tape machines, and released the first multitrack electric guitar recording on Capitol records in 1949... however, Sydney Bechet had released a multi-track recording using Paul's techniques back in 1941. 
Okay, maybe you’re not so ambitious and simply want to bash out a decent tune around a campfire. That’s fine — just be warned that doing any John Denver stuff hasn’t been considered cool for a long time. If you are guitar beginner with a guitar in hand already then I may suggest you check out: 10 Amazing Tips to Learn How to Play the Guitar with Good Technique.
The original run of Marshall Silver Jubilee amps were designed to celebrate Jim Marshall's 50th anniversary in music as well as 25 years of Marshall amps. These beautiful sounding (and highly sought after) amps have been brought back from extinction with the Marshall 2525H Mini Silver Jubilee Head, matching cab and combo and have been constructed using the original 2525 diagrams. This means you have all that vintage sounding goodness with modern reliability. You can even switch it from 20 Watt to 5 Watt power so you can go from live sound to home practice easily without ever losing your tone. A great amp for stage, home and studio recording.
What’s the point in having these lists anyway? There’s always going to be anger over people who were left out/included on the list when they didn’t deserve to be… And to say that any of the musicians mentioned so far aren’t talented is ridiculous, there’s no limit in the world on how much talent there is, so why does this list have to be limited to 10? Just saying…
Visit “mom and pop shops,” big-name musical instrument retailers, Craigslist, eBay & Amazon to compare the reviews and prices of various models. The ability to make an educated decision based on the feel, sound quality and playability is important. Consider renting a guitar for the first month of lessons. A good teacher will serve as a guide throughout the buying process and will teach you to play well enough to “test drive” your options.
Our site has a wealth of information about what goes into making a Taylor guitar and how to make this very important decision. We have guides for how to find the right fit for you. Learn about the subtle differences in shapes and styles. Delve into different types of woods and construction, which are vital to the flavor and tone of an acoustic. Explore the Taylor line by series to find the look and style you want for your instrument.
Cap in series with a resistor (shouldn’t matter which comes first). Kinman recommends this for single coils but it works rather well for humbuckers too. I installed 1nF cap in series with a 130K resistor and it works awesome. Resistor is there to limit the effect of the cap and having it in series with the cap means it shouldn’t affect pot taper as much. Larger cap means wider frequency range, so treble jump isn’t as sudden. So far, this is my favorite treble bleed circuit.
It comes with a single coil pickup in the neck position and a humbucker at the bridge - switching between the two pickups gives you both a strat like sound and an LP like tone. The pickup selector is 3-way so you can play with both pickups at the same time. It sports a shorter 24.75" scale length and smaller 12" radius on the rosewood topped mahogany bolt-on neck with a 1.6875" nut width making it very playable and accessible to guitarists of all levels of experience. Many customer reviews suggest the Empire HG feels and plays like a more expensive guitar.
I didn’t want to spend much money (I’m a cheap bastard…part of me thinks I could never truly love a 59 Bassman unless I scored it at a yard sale for a hundred bucks. Now, tone matters more than money to me, but I tend to love the tone of crappy amps just as much as high enders, so I’d feel like a stooge dropping that kind of money on an amp. Especially since I play them and would ruin the collectable value of anything by gigging with it).

Nitrocellulose lacquer is one of the great original-era Fender electric guitar finishes, and is still used today on select instruments. Thin, porous and delicate, it’s a premium finish prized for sonic qualities that let body woods breathe with their true tonal character, and for an appearance that ages and wears in a distinctive way appealing to many players.
To make frequency selective networks, we must use capacitors and/or inductors. Unlike resistors, both caps and inductors discriminate against some frequencies in favor of others. Capacitors preferentially pass higher frequencies; inductors pass lower frequencies more easily. Resistors help us set how much gets through, while caps and inductors select which frequencies get through. Inductors are big, heavy and expensive, so almost all tone controls use only caps and resistors.
The Blues Harp has been around since the early 1970s. Until the 1990s, it was functionally identical to the Marine Band, the only differences being the cover plates and the varnish on the front of the wood comb, and the Blues Harp's profile was thinner as well. At one point, Johnny Cash promoted the Blues Harp.[20] In the 1990s, Hohner made the Blues Harp part of its Modular System (MS) line. This new Blues Harp lost its uniqueness, and is interchangeable with the other models in the MS line, but it currently remains the standby of many players who use MS harps.

Bracing affects the way the guitar sounds because it changes the pitch or tune that the guitar produces out of the sound hole. Personally I think X bracing is the b est because it produces a more even and better more balance for mids and high notes and just enough bass on the E and A strings that gives a brighter more even tone. Blinded or pessed bracing gives a much deeper sound than x bracing which =less versatility but if you bought a pressed dread knot or anything else you'll still be okay just remember strings make a huge difference and running your guitar to the right amount of tone for any song will work it's just that Taylor produces the best over all guitar itself by better quality woods and they go through ver strict and rigorous testing and inspections before they are sold to retailers and customers. Higher grade parts attention to detail and style of music versatility is why one guitar can cost 3 times as much. Most companies like Taylor is know give warranties or $ back
The principal difference among the Strats was in finish options. All had 21-fret maple necks, three single-coil pickups, volume and two tone controls, and five-way select. The SWG came in yer basic red or black, with maple ‘board and chrome hardware. These had traditional non-locking vibratos. The SGV was offered in red with white graphics. The SSX was the dusey, with purple burst (white outside, purple in center), tiara turquoise, blue pearl, metallic white, black and candy apple red finish options, with… with matching colored maple fingerboard and (that’s and) matching chrome hardware.
When you dream of playing guitar, how does it all happen in your mind’s eye? Perhaps using a guitar app like Uberchord (click to download) to learn? Or are you shredding an awesome heavy metal guitar solo, sliding on your knees across a vast stage in front of thousands of adoring fans? Do you imagine a more intimate setting, jazzing up a storm in some exclusive New York nightclub? Is it amazing the crowd with your brilliant finger-picking at the Newport Folk Festival?
The movie is very hauntingly beautiful, and it's especially highlighted by an awesomely haunting score, and some breathtaking visuals. The story is interesting, but it's definitely slow-paced, and the climax is much more of an intellectual payoff than a spectacular action scene (which many viewers might be hoping for). So I can definitely see why some people would hate this film, but I loved it. It's one I definitely won't forget anytime soon too, and it's great to see Natalie Portman (my old favorite actress) back in top form! watch movies online pro
The electric guitar was essentially born in 1929—long before the advent of rock and roll music. The first commercially advertised electric guitar was offered that year by the Stromberg-Voisinet company of Chicago, though it was not a smash hit. The first commercially successful electric, Rickenbacker’s “Frying Pan” guitar, didn’t kick off rock ’n’ roll yet either, but it did inspire competitors to jump into the electric guitar market. Invented in 1931, the Frying Pan had an electromagnetic pickup made out of a pair of horseshoe magnets placed end-to-end to create an oval around the guitar’s strings, with a coil placed underneath the strings. The pickup, a device that converts the strings’ vibrations into electrical signals that can be amplified, was bulky and unattractive, but it worked. The commercial version of the Frying Pan was a hollow cast-aluminum lap-steel guitar, and wasn’t an immediate hit beyond some Hawaiian, country, and blues musicians. It differs from the traditional Spanish-style guitar in that it is played horizontally, on a stand or in the player’s lap, and has a sliding steel bar that can be moved along the frets for a gliding effect.

He may have spent much of his Guns n' Roses prime shirtless, drunk and surrounded by snakes, but Slash brought good taste and restraint back to hard-rock guitar. "It was a stripped-down rock & roll sound compared to what everybody else was doing," says Slash. He could riff like Joe Perry, and intertwine, Stonesstyle, with Izzy Stradlin. And lyrical solos like the from-the-mountaintop grandeur of "November Rain" were permanently laced into the songs' fabric. "It's hard to play those solos any other way," says Slash. "It will sound wrong."

The ghost Hexpander MIDI interface system adds MIDI capability to almost any guitar or bass.  Plug your guitar into pitch-to-MIDI converters by Roland or Axon and enter the MIDI sound universe.  The Hexpander MIDI interface provides responsive and accurate tracking unequaled be any other system on the market today.  Check out how affordable and easy it can be to make MIDI part of your music making.
After lowering the bridge (usually in a failed attempt at getting lower string action), the owner will eventually realize this is not the best solution. When this happens and a neck reset is preformed, the original bridge will now be *useless* (because it is too low!) The repair guy won't reset the neck to a low bridge, so a new replacement bridge will be installed. At this point the originality of the instrument is compromised.
By panning the distant mics to the opposite side of the mix from the close mic, you can create interesting panning effects for solos. "If it's a rhythm part, you get this huge sound because the whole thing is spread across the stereo spectrum." When double-tracking lead or rhythm parts, a useful trick is to reverse the panning of the direct and distant mics. "If there were two guitarists in a band, I would record them like that, so you got a wall of sound that had a transparency that would allow the drums and bass to come through."
I won't lie, I was VERY skeptical ordering this. But I figured that isfits not great, I could sell it. After getting it, this package is amazing for the money. I am definitely keeping it! I own/have owned $5,000+ models and some $100 "disposable" axes and I was shocked at this beautiful guitar. First off, the flamed top is gorgeous. It doesn't have a cheap look to it. The fret board is so so but you cant expect too much here. The frets don't have sharp edges and nicely done. The sealed tuners are smooth and after a minute of the inital tuning (with the included chromatic tuner), I played it for a few hours and it kept proper tune. The overall tone of the guitar is warm and projects well. I got absolutely no rattle or vibration. Then I plugged into the included amp. I will admit, the amp isn't great but but its a free practice amp. So I plugged into my Peavey and sounds awesome. It also came with a so so gig bag, few picks, a strap, a truss rod key, sorta cheap guitar cord, an extra set of strings, and batteries for both the tuner and for the preamp on the guitar. Speaking of that, its a 3 band EQ with a gain control, volume and a battery checker. I paid $140 for all of this and I will say that this is one of the best deals I have gotten in almost 37 years of me playing. If you want a good practice guitar and can even play a show, don't pass this one up. The guitar alone is worth 3x of what the whole package costed me. I think I'll check out more Glen Burton guitars.

The following open-tunings use a minor third, and give a minor chord with open strings. To avoid the relatively cumbersome designation "open D minor", "open C minor", such tunings are sometimes called "cross-note tunings". The term also expresses the fact that, compared to Major chord open tunings, by fretting the lowered string at the first fret, it is possible to produce a major chord very easily.[14]
If you are a beginner then you probably don't know what a ‘floating tremolo' is. Have a look at Floyd Rose, who made the first models. If you are looking at a guitar that has little tuners on the bridge, then it's probably a floating tremolo. For a beginner, they are a total pain in the butt. They are very hard to tune and a real pain to change strings. The cheaper ones go out of tune a lot too. If you know why you want one, then fine, but locking tremolos on budget instruments are usually rubbish, so stay clear of those for now!
Gibson also tops the list of best electric guitar brands that retain a consistent design. Among the popular models, the Les Paul is a favorite guitar that has been ruling the music world for several decades. It is a high-end, USA-made instrument that comes in a variety of variations. Other famous Gibson guitars include the SG, Explorer, Flying V, ES-335, and Firebird.
What makes a good beginner electric guitar? Well, it should be cheap and easy to setup so you can start playing immediately. After comparing almost 13 guitars, we believe that Squier by Fender Bullet Strat is the best electric guitar for beginners. You don't have to take my word for it, but there has been some pretty solid positive reviews about this guitar.
I like most of the the 814's I've played though they seem just a bit brighter than some other guitars along that range. I prefer Collins guitars they're kind of in between the Martin sound, and the Taylor's brighter sound. After recording with several different ones. My favorites productions are Collin's OM1A , and more affordable Blueridge, and Recording king. I prefer Rosewood back and sides, Adirondack top, mahogany neck, with ebony fingerboard. Although mahogany back and sides with Sitka/ Engelmann tops sound nice too. When recording I think (might just be me) that I get better note separation from the Collins
Add bite or presence by boosting between 2kHz and 6kHz, depending on the tone you're after. Little over 4-5kHz is produced by a guitar speaker, though going for a brighter DI'd clean sound is quite legitimate for artistic reasons. Similar-sounding electric guitars that may be conflicting within a mix can be separated to a limited extent by adding bite at different frequencies, though choosing two different-sounding guitars and/or amp sounds and examining the arrangement carefully usually works better. As a rule, single-coil guitars are best for cutting through a busy mix without taking up too much space, while humbucking pickups create a thicker sound which may be beneficial in recordings where there is only one guitar part.
I heard off of a great guitarist years ago when I asked him about fender and gibson he said they were expensive and not great and also said the Gordon Smith guitars played and sounded great and as they never advertised and were a small builder in the uk the cost was cheap for the quality of the guitar. A players guitar rather than a fancy looking guitar thats all show and less go. I think they are the price of a mim strat but great hardware not chinese.
Quality replacement pot from Bourns with DPDT pull switch for coil tap or other switched application.   Knurled 1/4" shaft fits most knobs.  Low torque, carbon resistive element, great replacement in many applications using passive humbucker or single-coil pickups.   Note that length of threaded part of shaft is 3/8" - measure to make sure that this is long enough for your application, especially if the pot mounts through the wooden guitar body.   (This pot will not work on Les Pauls, for example).  1 Meg Ohm, Special A2 taper preferred by guitar and bass players.  Nut and washer included.   Note: threaded bushing diameter is 3/8", like most 24mm "quarter-sized" pots.   Both pot and switch terminals are solder lugs.   Not designed for PC board insertion.
Let’s get it straight. Froo – Shawn – Tey. If you don’t know him, he’s the lead guitarist of the Red Hot Chili Peppers. Frusciante is the author of the brilliant chord progression on Under the Bridge, the haunting intro to Californication and the simplistic solo and riff on Otherside. If you’re the casual listener of the Chili Peppers, then you may wonder why John has made it so far up this list. But a tad of a closer look will reveal that his simple catchy riffs are the tip of the ice berg. One can catch a glimpse at his technical skill in the Dani California solo. A bit deeper and you’ll run into Lyon 06.06.06 in one of the B Sides. John takes his influences (Page, Hendrix) and mixes his own nuances into a sound that’s pleasantly different, but melodically having the same effects on you. A track to look out for on his solo work – Ramparts – showcasing four or so guitars layered upon each other in an introspective orchestra.
Was skeptical at first since I own a couple of vintage Martins. Aside from the LX1E being a sustainable responsibly built guitar that has HPL back/sides, hybrid neck/fingerboard, and whose soundhole smells like a Lincoln Log toy set this is an amazing find. Yup- it’s perfect for the overhead bin on airplanes, comes with a good gig bag, and sounds great plugged in. Experimented with .11 gauge string set, but this guitar is really made for either .12 gauge or a true .13 (medium gauge) strings set. This guitar is designed for the combination of heavier strings and assertive strumming or picking to create a sound that belies its small size. It welcomes being pushed, muted, and/or percussively played. Found the same to be true of Martin’s DX regular size guitars which sound amazing for what they are. While the E Sheeran LX model has his logos on it, this
If you want to combine the dynamics of a well-recorded drum kit with the pumping excitement you get from heavy compression, send either the overheads only or the entire kit to a buss and insert a nice-sounding compressor there. Set the compressor to a high ratio and low threshold and mix in some of this with the song. You may need to adjust the attack and release controls to get the effect you're after, but you don't need to blend in much of the compressed sound to really add punch and weight to a drum track. Nicholas Rowland
Here, the brighter/lower-value cap is engaged when the pot’s all the way up. As you roll it back, the larger cap is introduced, producing greater capacitance and a deeper treble cut. When you arrange caps in parallel, their total capacitance is the sum of their values. For example, I tried a .0047µF cap and a .047µF, so the minimum value is .0047µF (a very modest cut) and the maximum is approximately .052µF (a very dark tone).
Enter the polyesters and the polyurethanes. These plastics can be made into synthetic resins which harden after application the guitar body, making them more durable than nitrocellulose finishes. In some cases, UV light can be used to initiate the curing process of the resin, making the finishing process much quicker than the application of nitrocellulose lacquer.
Accompanying the Supro frying pan in the ’36 Peate catalog was the Supro amplifier. This had a small, rectangular cabinet with a round grillplate with the screws attaching the speaker showing around the edges. The grille cover was still similar to a resonator cover, with large diamond cutouts, backed with cloth, and finished with black wrinkle paint. A leather handle sat on top, and metal bumper guards graced the lower corners. No information is available regarding specs.
7) Yamaha quality can't be beat. I just returned from my friend's house and noticed his $1,000 Martin box splitting because of the dry Las Vegas climate. And, no I'm not a believer in guitar humidifiers because I believe a guitar should be made for the real world and not so delicate that it needs a humidifier. My friend and fellow old-time musician who has been working at Guitar Center here in Vegas for many years has seen them all come back over time because of splitting or warping except one brand that is... You guessed it, Yamaha! The reason you find them back ordered from time to time is because Yamaha actually gives their wood time to cure properly unlike other manufacturers who tend to rush their products out the door. And, this guitar is for my kid and for travel which means it needs to be exceptionally tough and well-made:)
You may not have considered Orange Amplifiers before, but they’re a company with a history that dates back to the early days of hard rock. If you watch footage of rock bands from the 1960s you’ll see Orange amplifiers onstage almost as much as Marshalls. The British amp builder has had its ups and downs since those glory days, but today Orange is as strong as ever.
Martin actually got into the electric guitar business in the late ’50s when it started slapping DeArmond pickups onto some of its acoustic guitars yielding the D-18E, D-28E and OO-18E. These pickups were the DeArmond humbuckers with chrome sides and a black center in a trapezoidal hole, large pole pieces along one side and smaller poles along the other. Prototypes of the D-18E began in 1958 and in 1959 production began on it plus the D-28E and OO-18E.
The OM-28 E Retro is one of the more recent guitars to come from Martin's OM line, and it is the consummate '30s era style acoustic guitar. The company took their time to carefully replicate vintage OM-28 guitars, from the aged solid sitka spruce top and solid East Indian Rosewood back & sides, down to the smallest appointments - resulting in a guitar that not only sounds amazing, but looks museum-level amazing as well.
In the early 1980s, some performers began using two-way or three-way cabinets that used 15" woofers, a vented midrange driver and a horn/driver, with an audio crossover directing the signal to the appropriate driver. Folded horn bass guitar rigs have remained rare due to their size and weight. As well, since the 1990s, most clubs have PA systems with subwoofers that can handle the low range of the bass guitar. Extended range designs with tweeters were more the exception than the rule until the 1990s. The more common use of tweeters in traditional bass guitar amplifiers in the 1990s helped bassists to use effects and perform more soloistic playing styles, which emphasize the higher range of the instrument.
Once everything is assembled, check through the instructions one last time for any additional notes on connections, power etc (don’t waste all your hard work by blowing up the board with the wrong power supply). Then plug in your pedal and give it a try. There’s a good chance it will work first time. If not, go through the instructions again step by step and look to see where the problem might be. Missed, incorrect, or reversed components are the most common causes and can be diagnosed just by checking each step carefully.
It’s not known how long this A group lasted – probably only a couple more years, except for the U-65RN. By ’76, the U-65RN was still around, now promoted with 17 watts, Hammond reverb, tremolo, 10 transistors, and a 12″ heavy duty speaker. This looked pretty much the same, except the logo was reversed in white out of a black metal strip above the grille and the power switch had changed. At some point, the U-65RN was joined by the UB-252 bass amp, offering 20 watts with a 15″ speaker, presumably similar and transistor. These are the only two Univox amps listed in a 1979 price list (contained in the 1980 book), though, as you see over and over, others may still have been available.
PRS, or Paul Reed Smith, guitars are a high-end luxury guitar brand that broke into the rock and roll scene in the 1980s. Famous guitarists such as Trent Reznor and Vince Neil could be seen wielding these beautiful instruments. In fact, that’s probably one of the first things you’ll notice about PRS guitars. They are absolutely stunning. They use high quality wood and only use the best cuts whether it’s their cheapest or most expensive models. Even the slightest imperfections are too much for PRS. Another aspect of PRS to take note of is how they have evolved over the years. PRS is not afraid to evolve their models and most, if not all, of their models have seen changes. They take time and effort to find mistakes in the older models and improve them. From pickups to the neck shape, PRS will change it if they feel they can improve it.
One possible way of dealing with the g string tuning issue (my experience has involved the low e more than anything) is to wind the string on the peg so that the winding goes up from the bottom of the peg, not v.v as it is done at factory. This reduces the angle at which the string sits relative to the nut and neck, potentially reducing the problem caused by the friction this angle creates when it contacts the nut. It will likely have a significant impact on the string staying in tune over time and you don't have to worry about filing the nut. A little nut lube might help too.
A selection of makers within the high-end, hand-built crowd of today do offer variations on the opamp-based template discussed above. Blackstone Appliances bases its Mosfet Overdrive on a discrete transistorized circuit centered around, yes, mosfets, and Klon’s Centaur pedal uses… well, who the hell knows? They cover the entire circuit board in epoxy goop to keep the cloners at bay, but this expensive overdrive certainly sounds different. Other popular boutique overdrives are found in the Barber Electronics LTD pedal, the Crowther Audio Hot Cake, and the Fulltone OCD. 

Note that we paid little attention to the power ratings of these amps. Judging a guitar amp by its power rating is usually a bad idea for many reasons. First, small increases in power have almost no effect on a guitar amp’s maximum volume. All other things being equal, doubling the power gets you only a 3-decibel increase in output, which is barely noticeable. To get double the perceived volume, you need 10 times as much power. A 100-watt amp might be twice as loud as a 10-watt amp, but a 20-watt amp will only be slightly louder than the 10-watt amp.
My favorite guitar effect is Tremolo with a touch of echo. This works well on songs with slower melodic guitar leads and slower rhythms. Tremolo is an effect that has a speed adjustment and amplitude adjustment. The speed needs to be adjusted to the song tempo. This was popular for many songs written in the 1950’s. If you are a guitar shredder you will not be happy with this effect. I have a Boss Guitar Pedal and Line 6 Pod XT and use this effect from the pedal. I am not crazy about software generated effects as there is not enough space on stage for all the equipment and adding a MacBook and keeping it from getting knocked around would be too difficult. After recording I have used Garage Band and this software is easy to use. I probably have four or five software packages and they are too overwhelming at times. I have given up trying to figure out how to use the software with my expensive Presonus 24 track digital AI Board. It is almost impossible to use these recording software packages without having expensive school training.

6) PLEASE DO NOT POST THE FOLLOWING: Memes, jokes/skits, rage comics, sub-related rant posts, spam, advertising of your goods or services, shill advertising, links to outside retailers (links in discussions are ok), gear for sale posts (head to /r/Gear4Sale). Comment manipulation (edits made to conceal behavior) is strictly prohibited. Market research is strictly prohibited.
{ "thumbImageID": "Talman-TCY10-Acoustic-Electric-Guitar-Vintage-Sunburst/581659000003000", "defaultDisplayName": "Ibanez Talman TCY10 Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Vintage Sunburst", "sku": "sku:site51500000016398", "price": "179.99", "regularPrice": "199.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Ibanez/Talman-TCY10-Acoustic-Electric-Guitar-Vintage-Sunburst-1500000016398.gc", "skuImageId": "Talman-TCY10-Acoustic-Electric-Guitar-Vintage-Sunburst/581659000003000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51274115042950", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Ibanez/Talman-TCY10-Acoustic-Electric-Guitar-Black-1274115042950.gc", "skuImageId": "Talman-TCY10-Acoustic-Electric-Guitar-Black/581659000001000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Transparent Blue Sunburst", "sku": "sku:site51274115042713", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Ibanez/Talman-TCY10-Acoustic-Electric-Guitar-Transparent-Blue-Sunburst-1274115042713.gc", "skuImageId": "Talman-TCY10-Acoustic-Electric-Guitar-Transparent-Blue-Sunburst/581659000012000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }
This is worse than the Rolling Stones magazine’s list. Paco De Lucia, Django Reinhardt, Andres Segovia, Sabicas, Wes Montgomery, Joe Pass, Jeff Beck, David Gilmour, Jimi Hendrix, John Williams (no, not the movie score composer) IMO the top ten. It’s much harder to play jazz, flamenco, and sometimes classical, than it is to play blues or rock. These guitarists are all infinitely greater than Jack White, John Frusciante, Tom Morello, or John Mayor.
Since treble frequencies pass through a capacitor, what would happen if you routed the positive lead THROUGH the capacitor rather than having it ground out frequencies?  The answer: just the opposite - the signal from you pickups would pass through the capacitor and only treble frequencies would get through.  Aha!  A new type of tone control.  The illustration below shows this type of wiring in a bit of an advanced concept.
Pressing a string against a fret reduces the vibrating length of that string to the distance between the pressure point and the bridge, thereby controlling pitch. On nearly every Western fretted instrument, the distance between frets is a semi-tone of equal temperament, assuring the easy achievement of strong sounding chords and single notes that fit our hemisphere’s usual expectations for rhythm sounds and melodies. Understanding the virtues and limitations created by the order of frets opens up the door to ways to escape their constricts, like bending strings, playing slide, using whammy bars, delving into extended technique or trying fretless instruments.
Rolling Stones best electric guitarist list should've been nicknamed the best average guitarist list. I didn't give this guy the time of day because I thought the bucket thing was to cover up how badly he sucks. Turns out it's the opposite. He's just weird. It's too bad the average person doesn't have the capacity to enjoy this type of advanced music.

At first it sounds kind of like a buzzsaw, but after listening to the song, people usually have a hard time getting the catchy riff out of their heads. The best part? It's one of the most fun beginner guitar songs and anyone can play it! The riff is played entirely on one string, the A string and consists of only three notes. Fun fact, the riff was supposed to be a placeholder for a horns section, but they loved the fuzzy guitar tone so much they never got around to the horns.
Judging by the tag in the sound hole, headstock logo, and general construction of the guitar I would think it's definite made earler than '86. Mine has a tag identical to this one but the date 16 5 78 is stamped onto it and it also has the name of the person who inspected it stamed on it. Interestingly I did notice your guitar has a different truss rod construction than mine. looks like yours adjusts from the head stock under the cover and mine is an allen adjustment through the sound hole. Don't know if they switched over to your style at a later date... food for thought. I have heard of some poeple reffering to these as Yairi built guitars even though they don't carry the Yairi headstock logo.
It’s easy to hear that Acoustic Revolutions is inspired by the Goo Goo Dolls, Counting Crows, Dave Matthews, but the loops are so perfectly dry and easy to mix that you can create a very modern sound. Volume II itself actually pushes the loops into that modern sound by pulling inspiration from popular indie-folk bands that dominated the first half of the 2010s.
Mahogany is a very dense, strong wood used in all parts of guitar manufacture except fretboards and bridges, which require harder wood. A mahogany neck and back are often found on short-scale guitars with maple tops. Another common combination is an all-mahogany body and neck (excluding the fretboard). Because mahogany is not very hard, it emphasizes the midrange and bass frequencies for a mellower guitar tone. Mahogany is a very resonant wood which enhances a guitar's sustain. It is generally a uniform rich brown color.
Turning our attention to the main controls on the front, it actually doesn’t look as intimidating to use as some owners of it make it out to be. Yes, you can get lost in tweaking and tinkering with amp models and effects until you’re blue in the face - but we actually find the interface to be nice and uncluttered, with all the footswitches and knobs nicely spaced out. On the top left there’s a small screen with some knobs surrounding it, and this is where the majority of your tweaking and editing will take place. Across the top are seven knobs which are meant to replicate what you would find on your amp. If you’re interested in the amp modeling part of the POD HD500X, you’ll appreciate having things like DRIVE, BASS, and PRESENCE immediately available. Two footswitches on the far left of the unit are responsible for up/down menu navigation, eight switches labeled FS1 to FS8 are assignable to individual effects, and finally there are two switches dedicated to the Looper function, and Tap Tempo/Tuner. You can also clearly see an expression pedal built-in on the right of the unit.
Though he was influenced by everyone from B.B. King to Muddy Waters to Chuck Berry and Bob Dylan, Hendrix’s complete artistic vision included elements of blues, funk, rock, psychedelia and utter chaos. His frequent use of effects like the wah and Octavia pedal, pioneering studio effects like “backward” guitar and flanging, and use of controlled feedback and the tremolo bar added another dimension to his music.
{ "thumbImageID": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst/J73165000002000", "defaultDisplayName": "Squier Strat Pack SSS Electric Guitar with Fender Frontman 10G Combo Amplifier", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Brown Sunburst", "sku": "sku:site51500000053102", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "349.99", "priceVisibility": "1", "skuUrl": "/Squier/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst-1500000053102.gc", "skuImageId": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst/J73165000002000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51500000053101", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "349.99", "priceVisibility": "1", "skuUrl": "/Squier/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Black-1500000053101.gc", "skuImageId": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Black/J73165000001000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "", "assetPath": "", "imgAlt": "" } ] }
Often, multi-effects pedals and processors can be more cost-effective than purchasing multiple stompboxes. They also avoid the potential noise and tone-degrading impact of chaining numerous individual pedals together. That said, many guitarists prefer the way certain dedicated pedals sound or operate, and will collect many single-effect stompboxes along the way. If you are looking at purchasing multiple effect units but don’t have any favorites, purchasing a multi-effects processor can be a money-saving alternative.
What makes the RG421 particularly interesting is the neck. The Ibanez Wizard III neck used is thin, fast, and very comfortable. These aspects makes it suitable for shredding as well as playing rhythm guitar. The bridge is a simple fixed unit that is paired with an above average set of tuning machines on the headstock. Overall, the RG421 is capable of holding a tuning even if you go a bit wild with string bending.

Keep in mind that the year the guitar was built is no guarantee that any individual guitar is in the optimum condition required to handle steel strings. Any Martin should be evaluated with care, and a top that lifts significantly in the bridge area or this is not firm, is a sign that lighter strings should be used. Or that the guitar is in need of attention by a qualified repair person.

The hollow body electric guitar rose to prominence when Gibson introduced the ES-150 back in 1936. Fully hollow body electric guitars (sometimes referred to as “Jazz Box” guitars) tend to have arched tops and large, deep bodies that allow the sound to fully resonate to produce an incredible full-bodied voice with amazing projection and depth. Jazz players and blues players really love the sound fully hollow guitars deliver. While the classic, larger-bodied fully hollow electric guitars definitely still exist, there are also a substantial amount of thinline fully hollow body electric guitars that guitar players may find to be more comfortable. Guitar brands such as Gibson, Gretsch, Ibanez, D’Angelico, Guild, and Epiphone provide guitar players with a fantastic array of fully hollow body electric guitars.