By placing two (or more) mics at different distances and angles from your speaker cab you will get two different sounds - and more variation will of course depend on whether these are the same model of mic, or different models. Mics placed further away will capture more room tone, and close mics are more upfront. Angled mics offer a less direct sound. Capture both feeds and blend or select from the two after recording.

Using that pickup and gain level, you should be able to hear some guitar distortion. Of course, if that's not entirely satisfactory, there are a few other things you can do. If your amp has tone controls, you can turn up the mid knob to hear the guitar distortion more clearly. If there's only bass and treble controls available to you, you can turn both of these down a little to hear more distortion.
Gold Plated strings are really just 80/20 Bronze & Zinc wound nylon strings.  They are also used to produce the bass wound strings of a set of classical strings.  They maintain their place in the market due to having a much brighter tone than silver plated strings and are used by many professionals due to their capability to project louder and sharper.
Unfortunately, a simple pickup with a single coil of wire is just as good at picking up stray electrical energy from power supplies and other interference, so it generates a certain amount of unwanted, background noise. Some guitars solve this problem using what are known as humbucking pickups. These have two coils of wire, arranged so they capture double the signal from the moving guitar strings to produce a richer sound. Each coil is wired up so any stray "hum" it captures from nearby electrical equipment is canceled out by the other coil. Most guitars have two or more pickups, which create a variety of different effects. Typically, there's one pickup under the bridge of the guitar (where the strings are supported) and another one slightly higher up at the bottom of the "neck" (the part of the guitar that sticks out of the main body).
Of course, for the guitar string vibrations to have an effect on the magnetic field of the pickups, they too need to contain a ferromagnetic metal; this can be either iron, cobalt, or nickel. There are a large number of different string compositions, but often they will consist of steel, a combination of iron, carbon, and sometimes chromium. The chromium can help prevent corrosion, as it forms a layer of chromium oxide which prevents the string from further attack by oxygen in the air. Additionally, the strings can sometimes be coated with various polymer additives to help inhibit corrosion. However, these additives can sometimes have a negative effect on the tone of the guitar.
Discrete models describing the low frequency behavior of stringed instruments have appeared in the technical literature for more than 25 years. These models are very useful in understanding the nature of acoustic-structural interaction, but only when they are correctly tuned to match the measured response of a particular instrument. The tuning process is easiest when FRF measurements are made... [Show full abstract]
click on the red highlighted portion of instrument that you want to download then click win 32 for 32 bit operating system..then copy the dll file and paste it into c:/program files 86 :/imageline /flstudio/plugins/vst and paste here refresh the fl studio by going add then channel and then more plugins and start scanning ..find that instrument by name and enjoy
Just as an Auto-Wah is a version of a Wah pedal controlled by the signal's dynamic envelope, there is an envelope-controlled version of a volume pedal. This is generally used to mimic automatically the sound of picking a note while the guitar's volume knob is turned down, then smoothly turning the knob up, for a violin-like muted attack. An example is:

Thanks for this explanation. I have built a few electric guitars, but they have been in the Gibson style with two humbuckers. I am now working on a guitar with an HSH configuration, so for starters, I needed to understand the basic 5 way switch, which if you just looked at it, it makes no sense. Now I see that the wipers of each pole are on the opposite end of each side.
The following chart will help you choose the right sized guitar for your child. It is important to note that guitar size is only one part of making it easy for your child to play. An un-adjusted guitar will not be easy to play, even if it is the right size. Here at FirstGuitar.com, each guitar is inspected, properly adjusted and set up so that the strings are easy to press down and the notes ring clearly.
Some bass amps have two inputs. One some amps, one is a high gain input and the other is a low gain input. On other amps, the two inputs may be intended so that two basses can be plugged in at the same time. On these amps, there may be a separate volume control for each input; this is done to enable a bass player to switch between two instruments on different songs (e.g., a fretted and fretless bass) without having to unplug and plug in jacks. For example, the vintage Traynor Bass Master tube head has two inputs, each with its own volume control. Some bass amps have an auxiliary in jack, for plugging in a drum machine, keyboard bass or synthesizer. Some bass amps also have an external speaker out jack. While this jack is also 1/4", a speaker cable must be used with this jack, rather than a patch cord, because it sends a powered signal out to an external speaker cabinet. Higher-powered and more expensive amps may have Speakon output jacks.

The Orange Crush is all about style and portability. It’s distictive look is due to the Orange basket weave Tolex, woven speaker grille, beading and legendary hieroglyphs (PiX) and of course the Orange signature ‘picture frame’ edging. It’s not as feature rich as other models, but that’s the point. It’s simple, portable and just a good basic combo amp. It’s also available in black (why?) and retails for around $99.
An utterly odd topic would be a discussion of woods for a certain tone. Wood does no magic to the tone. It has properties which might change the resonant behavior of a guitar body. But, that it does by some very course parameters, say stiffness and specific weight. Of very same importance is the shape of the plank which is referred to as “the body”. Stiffness, weight and shape work all together.
{"eVar4":"shop: guitars","eVar5":"shop: guitars: electric guitars","pageName":"[gc] shop: guitars: electric guitars: first act","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"gretsch guitars","prop5":"[gc] shop: guitars: electric guitars","prop6":"[gc] shop: guitars: electric guitars","prop3":"[gc] shop: guitars: electric guitars","prop4":"[gc] shop: guitars: electric guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] sub category"}
For instance, the guitars that have a solid body are the most numerous out there. These models are as sturdy as they come, but they do not offer one plenty of resonance and sustainability. If you are interested in a design that mimics the figure of acoustic units, then you should pay attention to those guitars that have a hollow body. These products are able to deliver plenty of resonance, but they might not be of great help when it comes to feedback.
This is the Autumn Brown El Dorado. The finish is outstanding, and it’s also very easy to handle at only 7 lbs. We used 24 extra fat frets. Dual humbuckers provide the sound, and it comes with a whammy bar. We used gold hardware to complement the nice finish. Like other Big Lou guitars, this one features our 1 7/8″ nut width and 8mm string spacing. The construction involves a “set” neck, so it can’t be swapped out, but the factory is ISO9001 certified, so this guitar is a very high quality instrument. Considering the price at $379, it’s a great value. I really tried to keep the cost down, but that arched top costs a small fortune to build. If you can make a statement by playing, that’s the best. But if your still in training, this guitar will make a statement just sitting there. I took the first one off the assembly line for myself. I had to have it.
The rhythm of a guitar itself leaves many of us awestruck. Though many a time, beginners have this question of how to play guitar tabs. Practically they are easy, but need a lot of practice. Nothing that's worthy comes easy in this world! There are some easy guitar lesson tabs which when practiced, can help to learn the instrument faster. Let's scroll through some of these easy acoustic guitar tabs for beginners, and enjoy the experience of these guitar lessons. To become a really good guitar player, it is essential that one knows how to read guitar music sheets.
ACTION: fret low E at first fret and measure the distance from the bottom of the to the top of the 15th fret. It should be 5/64". Do the same with the high E, measurement should be 3/64". Now measure the string height at the nut; underside of the string to the top of the fret. Low E and A should measure 2/64", D and G =1.5/64" and B and high E = 1/64". If string height at nut is correct, recheck string height at 12th fret with strings open. Measurement for low and high E's should be the same as measurement taken at the 15th.
The following songs have been selected to highlight some of the best electric guitar songs from the 1980s. Each song includes links to tab, and wherever possible links to free audio versions of the song. A guideline for the difficulty of each song has been included. The assumption with these guidelines is beginner guitarists can play the ​basic essential open chords, F major, plus basic power chords. Difficulty assessments do not include the guitar solos.
Buddy Guy: ash body with a V-shaped maple neck featuring a 22-fret fretboard, three Lace Sensor “Gold” single-coil pickups and a 25dB active midrange boost circuit (USA, discontinued as of 2010), alder body with a V-shaped maple neck featuring a 21-fret fretboard and three standardalnico single-coil pickups (Mexico). Available in a variety of finishes, including black with white polka dots (Mexican Artist Standard), 2-color sunburst and honey blonde transparent (USA Artist).
I just thought you'd like to know that Takamine produced for other names. I've just bought a 1973 Wayne which has a Takamine label inside stating it was made for Wayne. Its a Takamine 375 thats a Martin D35 copy. Wayne were guitar makers in Melbourne Australia in the 1950s and 60s and began importing under their name briefly in the 70s. It sounds amazing.

Eddie Kramer has a slightly different approach, working from a familiar setup of favourite close and ambient mics (including the Beyerdynamic M160 ribbon mic) and then mixing them together to taste. "I use a three-mic technique: an SM57, an MD421 and an M160, all in a very tight pattern. Then I can pick and choose the tone quality, because each mic is totally different. I combine these together, and then I put a U67 away from the amp to get the ambience."

{"id": "113503875", "categoryId":"site5AAG", "name":"Vintage Palmer Electric Solid Body Electric Guitar", "pageUrl":"/Used/Palmer/Vintage-Palmer-Electric-Solid-Body-Electric-Guitar.gc", "thumbnailUrl":"https://media.guitarcenter.com/is/image/MMGS7/NonExistingImage-00-180x180.jpg", "hasFeatures":"0", "isAccessory":"0", "message":"", "value":"", "priceMin":"", "priceMax":"", "msrp":"", "productVisibilityMSRP":"1", "restockPrice":"", "openBoxPrice":"", "clearancePrice":"", "isPlatinum":"0", "priceSavingsMaxPrice":"0.00", "priceSavingsMaxPercent":"0", "inventory":"0", "brand":"Palmer", "reviewStarImageUrl": "https://static.guitarcenter.com/img/brand/gc/cmn/Sprit-Sm-Stars.png", "reviewStarRating":"0.0", "reviewStarRatingInteger":"0", "reviewHowManyReviews":"0", "usedOrNew":"new", "discontinued":"1", "onOrder":"0", "clearance":"0", "canBeSold":"0", "accessoryCategories":"site5LFMIC,site5LAAA,site5HBA", "stickerText": "", "isVintage": "1", "outletonly": "", "checksum":"", "priceVisibility": "", "itemType": "Vintage"}
The Estimated Values shown on each web page are out-of-date in many cases. One person cannot possibly keep every page up-to-date, so that is why we created a Wiki system to allow anyone to help maintain the database. We invite anyone who sees a problem with any Estimated Value to report it to us by clicking the Report A Problem icon at the top of each page (it looks like this ).
Hello all. I have a brand name guitar, which was very popular in the 1980s, and still is being manufactured under Gibson today. I didn't see it in your list though. It's a Kramer Stagemaster. It's a beautiful guitar, which I may never part with. Strat-Style with Neck-Thru-Body & Floyd Rose Trem. The headstock states Kramer American. These were passed off as American made models, however I understand that they were actually made in Japan. The style and appointments are strikingly similar to my Ibanez Proline 2550 from the same era, which has 'Crafted in Japan' written on the headstock. I know that Kramer made a lot of American made guitars out of Neptune, New Jersey, however these were all bolt-on neck guitars. Does anyone know where these Neck-Thru Kramers were made, or why they have American printed on the headstock if they are not tues American made guitars?
From the jazz-tempered Artcore series to the metal-shredding Iron Labels and all of their rocking classic models, Ibanez electric guitars are definitely not confined to any one genre. You can play whatever music you like with the right Ibanez axe, whether you go for one of their off-the-shelf designs or the signature style designated by your favorite guitar hero.
This great book of interviews is, in my opinion, one of only a handful of truly essential record-production books, and is packed with down-to-earth recording advice, as well as discussions of the art of production. In addition to the interviews I've referred to in this article, the book also features such greats as Glen Ballard, Arif Mardin, Brian Wilson, Phil Ramone, Mitchell Froom, George Martin and Geoff Emerick, and one of the strengths of Massey's approach is that he often asks them similar questions, which makes for interesting comparisons.
5.  Customer installed strap button on heel of acoustic.  This was a simple job that went horribly wrong because a pilot hole wasn’t drilled.  Result:  Cracked heal.  Fix:  Careful application of cyanoacrylate glue and touch up refinish.  I’ve also seen strap button installations on guitars with bolt on necks where the pilot hole has hit the threaded insert in the heel.  Make sure you know where the insert is placed on that particular guitar before you drill.

When you've put your blood, sweat and tears into developing your talent, you want your music to sound amazing. And with the proper recording gear, you can ensure your sound is captured exactly how you intended. From audio interfaces to studio monitors to extremely powerful subwoofers, this section's wide range of recording gear offers up plenty of examples of ways to make your recordings better than ever. The right audio/video arrangement can take the stress out of recording, giving you more time and energy to concentrate on what's most important - your music. If you're unsure where to start the search for recording gear, checking out some of the top-rated and best-selling products is definitely the way to go. Want to attach your mic directly to your PC or Mac? The Blue Icicle performs dual functions as an XLR to USB adapter and a studio-quality microphone preamp. Offering a quick and easy way to perform digital and audio recording, this handy tool is a must for every musician's gear bag. Maybe you're in the market for a studio monitor? If that's the case, the Mackie MR8 mk3 8" 2-Way Powered Studio Monitor is a fantastic choice. Built with a clear focus on accuracy, this low-profile studio monitor is perfect for musicians who really want to capture the full character of their music. This section is also home to an assortment of GoPro video cameras. With a GoPro, you can record your set firsthand from the stage, giving your fans a unique "view from the top." Take a look at the GoPro HERO+ LCD for example - this camera captures your world in stunning HD video. It's rugged, waterproof and built into its own protective case - exactly what you need to record those high-energy shows. Another fantastic GoPro option is the HERO4 Session. Smaller and lighter than any other GoPro currently on the market, the HERO4 Session captures 1080p60 video and 8MP photos in a simple design that's so compact it can go just about anywhere. This is just a quick sampling of what's available when it comes to recording gear. There are lots more products to consider, so spend some time browsing through them - you never know when the right piece of equipment is going to leap off the page and into your professional setup.
In late 1960, the amp was redesigned with three, rather than two, channels, each with two inputs, and offered with an optional Top Boost, or Brilliance, circuit, which introduced an extra gain stage and separate bass and treble controls. The Top Boost feature proved popular enough that it became standard on the AC30/6 (so named for its six inputs). Its chimey high end was a signature of the Beatles’ early recordings and was later favored by guitarists like Brian May, Tom Petty, Peter Buck and The Edge, whose 1964 AC30/6 has been featured on every U2 album.
With over 100 effects, there's really no shortage of virtual stompboxes to play with, while the unit's complex signal routing capabilities allow for a wide variety of effects combination. Add to this Helix' acclaimed amp modeling features, which lets you mix and match 62 amp, 37 cabs and 16 mics. If that's not enough, you can also make adjustments to the amp models to better personalize your sound. To match its complexity, Line 6 designed the interface to be simple yet intuitive, courtesy of its color LCD display and colored LED rings.
Those of you familiar with Van William’s former bands Waters and Port O’Brien, will have suspicions about what to expect from the songwriter’s debut solo material: boisterous, vibrant hooks that are easy to swallow but gut you on their way back out.  His latest incarnation represents a bounce back after a period of personal tumult. Two parts power pop bombast, to one part Americana, William’s maturation as a songwriter and guitarist seems to have hit a new high water mark.
To cut to the chase, we can say that a changing magnetic field generates or "induces" electricity. It's also true that a changing electric field generates magnetism. If you feed electricity through a coil of wire, you generate a magnetic field around it. That's how you can make a magnet controlled by electricity—better known as an electromagnet. Electricity and magnetism are really two different aspects of a single phenomenon: electromagnetism.
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Ash - Neck Attachment: Set - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Inlay: Pearl - Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black - Pickups: Ibanez - String Instrument Finish: Natural Blue
A bass stack may use a single speaker cabinet (e.g., the huge 8x10" cabinets widely used by hard rock and metal bassists). The 8x10" cabinet is often provided as "backline" equipment at music festivals; this way, all the bassists from the different bands can use the same amplifier and speaker cabinet. This reduces the transition time between bands, because the roadies do not have to remove the previous band's bass stack and bring in the subsequent band's stack. Using one 8x10" as backline gear for an entire music festival also makes the transition easier for the audio engineer, because she can have an XLR cable plugged into the amp head's DI unit output (to get the bass amp's signal so that it can be mixed into the sound reinforcement system mix) and have a mic set up in front of the cabinet, to capture the amp and speaker cabinet's distinctive tone. The 8x10" cabinet is widely used by heavy metal music, hardcore punk and psychobilly bassists, as these genres use a loud onstage volume. Some metal bassists, such the bass player for death metal band Cannibal Corpse, use two 8x10" cabinets for large concerts in stadiums or outdoor festivals.

Many newbie guitarists seek out distortion effects because they don’t like the distortion sound that comes with their amp. Analog distortion and overdrive pedals can help, but it is important to realize they are not magic bullets. Even the best distortion pedal is still at the mercy of the amp you are playing through, and the same pedal will react far differently whether played through a 100-watt tube head or a 40-watt solid-state combo.

Fender Hot Rod Series Pro Junior III 15W 1x10 Combo - This tube-driven guitar combo with a 10” Eminence vintage-cone speaker reproduces the harmonically complex output and sensitivity to playing synamics that vintage Fender tone hounds love. Dual 12AX7 preamp and EL84 power amp tubes crank out the same celebrated midrange as vintage combos. Fender has updated the Pro Junior III with an external speaker jack, a more legible control panel, and internal tweaks.

Jeff Beck: select alder body with a thinner C-shaped maple neck, contoured neck heel, rosewood fretboard with 22 medium-jumbo frets, three dual-coil Ceramic Vintage Noiseless pickups with 5-way switching, LSR Roller Nut, Schaller locking tuners and an American 2-point synchronized tremolo with stainless steel saddles. Available in Olympic White and Surf Green finishes (Artist Series, Custom Artist), as well as a “Custom Thinskin Nitro” version with a “Thinskin” nitrocellulose lacquer finish.


THE CONTROL CAVITY Routing the control cavity is just as important as the neck pocket but with a couple more steps. The best thing to do is to cut out the plastic cover. Trace the pattern that you came up with for it on the plastic then cut it out with a jig saw. Use a fine tooth blade to prevent the plastic from chipping and will also yeild a smoother cut. Once this is done, take your template and reverse it, trace the patern on the back side of the body. Next set your router to a depth that is the same as the thickness of the plastic plate and rout the cavity working out to the line you drew. I do this free hand since the first cut is too shallow for a template. Be careful when you do this and test fit the plate you cut to make sure you get a goo fit. Then you will draw another line about 1/4" along the inside of the cavity you routed out, leaving extra room in areas for the screws you will use later on to secure the control plate. Rout this area out in the same way, working out to the line you drew. When you start to get close to the half way point in the wood start to think about how much wood you need to leave at the bottom. Usualy 1/4" is good but make sure you are careful! I miscalculated once and ended up going all the way through the body. Bad experience.
Guitar from Spain is the best online store to buy the best spanish guitars online: Classical guitars, Flamenco Guitars, Acoustic Guitars and electro acoustic guitars made in Spain from the best spanish guitar makers at spanish local prices. These unique guitars will be delivered from our warehouse or from the manufacturer's bench to your door, avoiding extra costs or double margins. Because we only sell guitars from the most reputable Spanish manufacturers, you will be assured to buy only the best spanish guitars available with 2 years warranty and certified from origin. Spanish guitar brands like Alhambra Guitars, Raimundo Guitars, Ramirez Guitars, Admira Guitars, Camps Guitars, Rodriguez Guitars or Prudencio Saez Guitars are among the most reputable and best sounding guitars in the world. These guitars are manufactured in Spain, the land of the flamenco guitar and the classical guitar. At Guitar From Spain you can also buy steel stringed acoustic guitars, western guitars and electro acoustic guitars made with the same traditional craftsmanship and know how acquired through centuries of guitar making. We also have special guitars as Bandurria (Spanish mandolin), Laud (Spanish lute), Cuban tres, timple canario and special sized guitars as Cadete (guitar 3/4) Requinto (Guitar 1/2) and Senorita (Guitar 7/8). Compare our Spanish Guitars with any other "asian made guitars" at the same price and you will be amazed with the diference in quality and sound that you can get. Do not settle for imitations, buy the original, buy Guitars from Spain.

Three recording sessions between 1936 and 1937 produced 29 songs, including the verifiable classics “(I Believe I’ll) Dust My Broom,” “Sweet Home Chicago,’” “Walkin’ Blues,” “Love in Vain” and “Crossroad Blues.” His popularization of cut boogie patterns presaged electric Chicago blues and rock and roll, while his fretted and slide guitar licks are so timeless that they still show up in contemporary music.
This guitar could have rocked around the clock. Bill Haley and many other early rockers used guitars just like this baby. They have a sound of their own, and just breath taking, to say the least. This Harmony H38 dates to about 1957-59. She's completely original except for the button input jack that someone installed. This guitar puts a chill in cool. There's just something about playing a Vintage Harmony. $799.99
After a certain point of decreasing the price on the amplifier systems you are offering to the buyers, you get a return in the shape of an increasing size of the amplifiers themselves. Which is not really that much of a problem, especially when the Fender speaking you are talking about look vintage and sounds like it could be from the future. The Fender Mini Tonemaster Battery Powered Electric guitar amp is a little on the big side among smaller amps, in terms of size and in terms of sound. While it might be a little tiring to carry with you, the sound you are going to produce for the price of almost nothing is going to feel worth it, every second of the song.

Play a classic 6120 or Duo Jet and it can seem a bit, well, old-fashioned. A growing number of players desire the brand’s looks, sound and unmatched vibe, but also want something a tad more versatile and user-friendly. Enter this latest Players Edition model with its neck set lower into the body for improved access, higher-output Filter’Tron-style humbucking pickup (Full’Trons) and a modernised Bigsby vibrato where through-stringing replaces the notorious ‘hooking the ball-end over a peg’ system that scuppered any chance of a quick change. Mate these modern tweaks with another recent innovation (for Gretsch, at any rate), the Centre Block range, and you have a guitar ready to compete with anything out there - in virtually any style.
Thanks for popping in! Yeah, that g-string issue's a real pain. I also get it on acoustics for the same reason. I've found that, aside from sloping the slot DOWN on the peghead side, if you also try to provide a gentle (side) edge where it starts to head towards the g tuner, that helps too. What I'm trying to say is that you should try to give as clear a path as possible to the tuner to reduce interference/friction. I've tried to illustrate what I mean here: https://lh3.googleusercontent.com/-_9c955WEOiM/UI8xvC_nvFI/AAAAAAAADAA/RQmXf_beWUc/s754/nut-slots.jpg but let me know if it's not clear. More on making a nut here, by the way: http://diystrat.blogspot.tw/2010/10/making-bone-nut-from-scratch.html
While there's nothing necessarily wrong with plonking your mic right at the centre of the speaker cone if it gets what you're after, a lot of producers take the time to experiment with different positionings off axis, where the sound is typically warmer. Mike Hedges: "Depending on where you have [the mic] — outer speaker or inner speaker — you get the difference in tone from the edge of the speaker and the centre of the cone." In fact, Mike Clink also tries small changes in position even when working with basically on-axis sounds. "I'll point [the SM57] exactly dead on, though I might move it an inch or two to get the right sound."
Enlarging/ Drilling Holes: Often required to upgrade tuners, or occasionally to change control pots. Enlarging a hole in wood seems simple enough, and it is. But it's also an easy way to ruin the finish of the guitar and worse. The problem is because there is no wood in the center of the hole, the edges pull upwards instead of cutting. It often results in large ammounts of chipout or worse. The answer is to run the drill BACKWARDS. This will ream the hole out without the risk of chipping. If the hole needs to be made significantly larger, it is often best to use a bit one size up from the desired hole size and run it backwards till the drill has gone just below the surface. Now you can drill the desired size hole normally relatively safely. The washers or dress rings will hide the slightly larger starting bevel that remains. Whenever possible, drill half way through from both sides or clamp a "backer board" in place. Do NOT use much pressure on the drill, let it do the work, excess pressure is usually due to dull bits, and almost always results in some king of damage. If you must drill through the finish where there is no hole use the same method as described for significantly increasing the size of a hole, but apply masking tape over where the hole will be drilled prior to starting.
The dynamic mic’s strengths for close-miking constitute some of its weaknesses in distant-miking, and you’ll more likely want to use a ribbon or condenser mic for this job, if you have one. Distant miking really begins at 10″ to 12″ out, where many condenser and ribbon mics start to bloom. As a rough guide, start 12″ to 18″ from the speaker in order to record an electric guitar sound that is still pretty solid and direct, but captures some sense of air and space and natural room reverberation. You can aim the mic straight at the center of the speaker for a bright and detailed tone, as described in our close-miking techniques above, or move it around in the field, trying different direct and off-axis placements. Any position that achieves a desirable tone is valid, and you don’t have to remain on the same plane as the speaker itself. Moving the mic out adds more space to the sound (while potentially compounding phasing issues – see below). Raising the mic above the speaker and aiming it down slightly to fire toward the upper edge of the cone can let the sound bloom as it reaches the mic. In a room with a carpeted floor, you can position the mic lower to the ground (even below the speaker itself) to cut out some of the reflected sound. Positioned as such, an end-fire mic can be shooting either toward the amp on a plane that hovers above the floor or at an angle toward the speaker, while a side-fire mic can be aimed either way or fire straight at the ceiling with the amp sound washing over its capsule.
Humbuckers use two magnets, one which works as a pickup and one which cancels out 60-cycle hum (hence the name humbucker). These pickups generally have a darker voice and a higher output, which allows them to perform better under high levels of distortion. These pickups also tend to sound better playing jazz, as the genre benefits from the darker voice these pickups provide.
The hollow body — the original electric guitar design — is completely hollow on the inside, like an acoustic guitar. Hollow-bodied guitars like the Gibson ES-150 saw use in jazz ensembles by players such as Eddie Durham and Charlie Christian, but were also adopted for country, folk and, eventually, rock and roll. If you’re looking for warm, mellow tones, the hollow body is your best bet. That isn’t to say it can’t give you some sweet, raunchy distortion. A proper hollow-body setup can pull off a great classic blues or rock sound, but they are more prone to feedback than solid body guitars.

Lastly, there's Session mode. When you need to take a break from structured lessons or just want to shred for a while, enter this mode and play to your heart's content. Rocksmith 2014 will even provide you with a backup band: tell the game what instruments you want in your power trio or quartet and the AI will follow your lead on the drums, bass, keys or anything else in its arsenal. We highly recommend the kazoo.

When looking at acoustic pianos, there are so many variations that can lead to differences in tone: upright vs. grand, hammer types, mechanical condition, the player, mic choices, and mic techniques. No matter what, though, the piano tends to be a behemoth in the mix – for better or worse – so most often you'll be looking to cut holes out for other things in your mix.

A right handed 6 strings, electric guitar that mostly comes in black. The body is made from mahogany, while the fret board is made up of rosewood. The fret board is composed of up to 22 frets of 2.7 mm in size. It additionally has beautiful electric features such as a 3 way toggle and a push and pulls volume and tone. Price ranges from INR 21,400-21,541. Click below to get more product details.


I didn’t want to spend much money (I’m a cheap bastard…part of me thinks I could never truly love a 59 Bassman unless I scored it at a yard sale for a hundred bucks. Now, tone matters more than money to me, but I tend to love the tone of crappy amps just as much as high enders, so I’d feel like a stooge dropping that kind of money on an amp. Especially since I play them and would ruin the collectable value of anything by gigging with it).

The models in this list of best acoustic guitars have their own visual charm that appeals to different people. For example, the Blueridge BR-160 has those ornate inlays on the headstock. Some guitarists love those kinds of design elements, while others may find them a bit over the top and would much rather prefer the fretboard inlays on the PRS Angelus, or the simple but classic cutaway design of the Taylor 110ce.
Strings produce sound in the guitar. In electric guitars, because there are no holes, the vibration is passed to a pickup which senses the vibration of the strings passes the signal on to the guitar amplifier. There are two types of strings for electric guitars, light and heavy gauge. Lighter ones are easier to play and allow easy bending of notes, but they are more likely to break and produce less volume. On the other side, heavier ones produce high volume but are hard to play and require more finger pressure to bend notes.
Featuring a comfortable neck and solid spruce top, the Epiphone Dove Pro Acoustic-Electric Guitar rings out with full, rich sound. Based on a design going back to 1962, the Dove Pro is equipped with a Fishman Sonicore pickup system that accurately reproduces its acoustic tone when you plug the guitar into an amplifier or PA system to play with amplified instruments. A terrific value.
Most guitars and basses have one or more tone knobs, which offer a simple form of EQ control. Using these tone knobs adds or cuts the treble frequencies of the instrument’s signal. Most guitar and bass amps also have some tone control available, usually in the form of a 3-band EQ section, allowing you to control bass, mid, and treble frequencies with independent knobs. These knobs boost or cut frequencies when you turn them up or down. Some amps and effects offer more precise control of equalization as we’ll see next.
Being part of the Gibson family, Epiphone today makes a variety of officially-sanctioned Gibson classics, including the Les Paul, which comes in versions including the Tribute with authentic Gibson pickups and the Special II with Epiphone's own pickups. There are also Epiphone editions of the timeless Gibson SG, like the G-400 Pro which is available in right or left-handed versions.
As I’ve mentioned before, the topic of guitar pedals can really be a rabbit-hole and some people get really, really into them. They are very often the key to the tone you keep chasing after. However, at the end of the day, a lot of your sound depends on your ability to play your instrument, so please don’t neglect practicing your instrument over trying out different effects.
We consider the finest tonewoods to be those with superior projection and sustain, and without weak or bright spots within the tonal range. Many of the wood species from the US Pacific NW meet this criteria, and more. Some were well known by luthiers, but others, like Myrtlewood, Claro, Franquette & Bastogne Walnut, Port Orford Cedar, Redwood, Pistachio, Olive, Osage Orange and Douglas Fir are just now gaining notoriety.
In the Ethereal reverb, you can layer two delay effects, where both have four different delay types to choose from, via the black button labeled "Delay Modes." These modes allow you to assign different subdivisions to each delay layer which, when stacked on top of the reverb effect, give you some really unique decay sounds that trail off from the initial signal. 
Clear and easy to follow instructions. I re-wired my Gibson Les Paul 60's Tribute for new pickups after removing the easy connects and circuit board that came stock. I ended up re-using the 3 way switch that came in the guitar instead of the one in the kit since it was shorter and the guitar didn't have room for the full length switch in the kit. They were both Switchcraft so same quality. I'm very happy with the results. After shopping prices, the kit is very reasonable versus buying the components separately.
With analogue delay (and simulations thereof), each subsequent echo is not only quieter, but also more distorted. Dub reggae tracks often make prominent use of this effect -- look out for the effect where the engineer momentarily turns a knob so that the echoes get louder instead of quieter, surging and distorting before he turns it back down again so they can die away.
Schooled in flamenco and jazz, Robby Krieger pushed beyond rock at a time when most players were still bound to the blues. In the Doors, he had the improvisatory flair to follow Jim Morrison's wildest journeys, wrote some of their biggest hits ("Light My Fire"), and picked up the slack in their keyboard-drums-guitar lineup. "Not having a bass player… made me play more bass notes to fill out the bottom," he said. "Not having a rhythm player also made me play differently, to fill out the sound. I always felt like three players simultaneously."

As the name implies, TheFretWire DIY 175 kit is based on the popular ES-175 hollow body guitar, following its shape and configuration, but using more cost effective materials. More importantly, it lets you customize your own archtop as you prefer - you can make it into a classic jazz box, or add some cool paint jobs to turn it into a rockabilly style instrument.


1961 is the sweet spot for Fender Strats IMO: the best 3-tone sunburst and tone! My 1961 Strat has been called one of the best sounding vintage Strats by Scott Freilich of Top Shelf Music, who has been working on vintage guitars since 1968. This Strat is the closest thing to that incredible Strat; this is a very rare opportunity for anyone looking for the classic vintage Strat tone without equal!
Instrument amplifiers are available in a wide range of price, quality, and performance levels. Some are designed for beginners, such as small, low-wattage practice amps, which typically have a single 8" speaker and about 10 watts, or smaller "combo" amps with relatively low wattage (15 to 20 watts) and a single 10" speaker. Mid- to large-size "combo" amps with 30 to 50 watts and one 12" speaker or four 10" speakers are best for high-volume situations, such as band rehearsals and onstage performances. For large venues, such as outdoor music festivals, guitarists may use one or more 100 watt (or several hundred watt) heads with one or more 8x10” cabinets. Some guitar amps are strongly associated with specific instruments or genres, such as the Marshall amps, which are widely used in heavy metal music.

I believe its an 80's model it has some wear n tear but makes it look good and ventig. But there is nothing on it but the bently sign on the headstock.its jet black has a bridge not string through. Two hummbuckers I guess. A treble and rhythm switch up by the neck on the top. It is a 22 fret with pearl inlays. Someone shoot me an email n ill send picks of it. Just want to know what I got my hands on.
Obviously, what I've done is to give myself a choice of three different sounds--a close, ballsy sound, a mid-range room sound, and a more distant room sound. By setting all three mics up at the same time, putting them each in a different input, and assigning them all to the same track on tape, I've given myself the option of having any one of those sounds immediately available to me, or a combination of them.

The panel on top carries the controls for an old school look and feel overall, consisting of a master volume, gain, bass, treble and the model AC10 comes equip with a built-in reverb effect that makes it even more powerful and articulate to use. This amp is at top of its class when used at home, awesome for a recording studio and bringing it on stage to cover a small to medium size venues.
In late 2013, it was announced that Absara Audio of Port Jefferson Station, New York, had purchased the rights to the Supro trademark from noted electronic engineer Bruce Zinky.[7] Zinky himself had used the Supro name for a series of amps beginning in 2005 from his company, Zinky Electronics. Absara announced in January 2014 that a series of new Supro amps would debut at the Winter 2014 NAMM Show in Anaheim, California.[8] The new Supro amps are cosmetically reminiscent of their progenitors from the 1960s.

The amplifier includes buttons for four different amplifier simulations: Clean, Crunch (a typical rock/blues sound), Metal (self-explanatory), and Insane (a version of Metal that our panelists found so distorted as to be nearly unusable). Like the Champion 20, it has a gain control (which is labeled Drive), and it adds a midrange control to its bass and treble controls.

The Vox brand was also applied to Jennings's electronic organs, most notably the Vox Continental of 1962, whose distinctive trademark "wheedling" tone was immortalised by Alan Price on the Animals' track "House of the Rising Sun". In 1962 the Vox Continental was given to The Echoes to trial on stage and use on records they cut with Bert Weedon and Dusty Springfield as well being featured on their version of "Sticks & Stones" 1963 as well many other records, and later used by Paul Revere of Paul Revere & the Raiders, as well as Ray Manzarek on most songs recorded by The Doors and by John Lennon on The Beatles' track "I'm Down", both in the studio and live at their 1965 Shea Stadium concert. Doug Ingle of Iron Butterfly used it on "In-A-Gadda-Da-Vida" and other songs of the group. Mike Smith of The Dave Clark Five and Rod Argent of The Zombies also made frequent use of the instrument. Peter Tork of the Monkees can be seen playing the unusual looking Vox organs several times during the Monkees TV series (1966–1968). In newer popular music, the organist Spider Webb of the UK garage band The Horrors can be seen using a Vox Continental. A famous Vox organ riff can be heard on "96 Tears" by Question Mark & the Mysterians. Benmont Tench of Tom Petty and the Heartbreakers has frequently used his vintage 1965 single Continental in the studio with the band since 1976 and still uses the instrument today. Another famous signature Vox organ sound was created by Augie Meyers when playing with the Sir Douglas Quintet, as heard in the songs "Mendocino" and "She's About a Mover."
My first recommendation is Epiphone. It is not just one of the best but it is the best guitar brand for beginners who are looking to buy a guitar to learn the ropes. I have included a few recommendations from this brand in this post. If you don’t know which one to buy and you are a beginner then buy one from this brand and you won’t go wrong for sure.

Wah pedals make exactly the noise they’re named after – yep a “Wah” noise! If you say to yourself “Wah, Wah, Wah” slowly, that’s the same sound the pedal makes. Imagine a baby crying in slow motion and you kind of get the idea. The Wah sound was probably best captured on “Foxy Lady” by Jimi Hendrix and is widely used in funk and rock solos thanks to its really cool sounding effect.


Another application of a fuzz pedal is available when the user has control over the the amount of feedback signal routed back into the transistor loop while the pedal is engaged. By configuring the feedback to more sensitive levels, the pedal will feed back into itself causing oscillation*. As the pedal oscillates, certain frequencies will be produced, causing a singing sustained note without the guitarist playing anything at all. The player can consequently play over the note produced to cancel out the feedback loop, but once the player stops the pedal will feed back into itself producing the configured signal once again.

THE NECK POCKET The next step is to rout the neck pocket and body cavities. For the neck pocket I like to use a 1/4" bit and leave the scrap wood edge around the body to give the router the extra support it needs when routing the neck area. To find out how deep you will have to rout the pocket measure the total thickness of the heal of the neck. Then measure the hieght of the bridge from the bottom to the top of the groove the string will sit in on the saddle and add about 1/8" to it. That allows for the string clearence over the frets. The subtract that from the overall thickness that you came up with when you measured the heal of the neck. That will give you a pretty accurate depth that you will need to carve the pocket down to. Be very careful when you rout the neck pocket! You don't want to make it too big otherwise you end up with gaps between the neck and the body and you don't want to go too deep because it can be impossible to fix. Rout a little bit at a time, and set the neck in each time to make sure you get the proper fit. It shouldn't fit to tight and the pocket should be slightly lager than the heal of the neck because you will have paint accumulation in it which will shrink it a little.


Power attenuation[when defined as?] can be used with either low-power or high-power amplifiers, resulting in variable-power amplifiers. A high-power amplifier with power attenuation can produce power-tube distortion through a range of listening volumes, but with a decrease in high power distortion. Other technologies, such as dual rectifiers and the sag circuit[jargon]—which should not be confused with attenuation—allow high power amplifiers to produce low power volume while preserving high power distortion.[27]
Gibbons has also twisted more than a few towering tall tales in his time, but his life is so surreal that it’s hard to tell where the truth ends and the trip takes over. His colorful manner of speech, known as “Gibbonics,” has made him one of Guitar World’s favorite interview subjects, especially since his poetic ponderings are loaded with insight, wisdom and a unique sense of humor.
Here we have a well aged Vintage Washburn D12/br from 1989 its a D-18 type with a cedar top and man does this cedar top sound great…it was surprisingly sound and deep for a late 80s it has a mature balanced tone…I like it with its pretty good bass response and all. Its structurally great no cracks and no playability issues what so ever its neck and alignment integrity is also excellent as the action is good and the guitar is as a result easy to play. Cosmetically this guitar has been around the block its no sissy its stood the test of time and its previous owner and still all in all with all its obvious nicks and scratches and various doinks man it looks pretty darn vintage COOL and I loved it I thought you might like it too just take a good look for yourself if your the type that likes a well warn in vintage guitar and you don't really mind that it has some extra character and soul this just may be a guitar you might appreciate….. its own beauty from life playing and enjoying the music experience this guitar has been well loved and played yet it is no where near warn out it has years of life left in her she just wants to really sing for someone and in my assessment she’s ready to be enjoyed for another 30 years or more! Very cool vintage Washburn Dreadnought guitar. Its neck is straight and has the proper relief its Tuners are real good sealed gears and doing an excellent job to this day, This one has the medium slim taper neck with the Diamond volute like the old Martin style…nice touch Washburn. Mahogany Back and sides and neck with rosewood fingerboard its neck width is 1-11/16ths at the nut. This a a well built good player folks if you don’t mind it not being exactly mint cosmetically its actually beautiful in its own vintage appeal. Any questions or to make the purchase you can contact Joe at: JVGuitars@gmail.com.

With so many guitar manufacturers hot rodding the Stratocaster, it is refreshing to see brands like ESP going after the other popular guitar shape, resulting in the "Super LP" guitar like the ESPT LTD EC-1000FM. This souped up version of the classic single cutaway body combines traditional looks with modern tones and playability, resulting in a fast playing axe that's easy on the eyes, and not too edgy.
The Air Norton started out simply to be the Airbucker version of the Norton. DiMarzio thought it would make a distinctive-sounding bridge pickup with high-gain amps, but they soon discovered that it's a radically neat neck pickup, too. The tone is deep and warm, but not muddy. It's hot, but not distorted. It's even got cool harmonics, which are really unusual for a neck humbucker. The patented Air Norton magnetic structure reduces string-pull, so sustain is improved; and pick attack and dynamics are tremendously controllable and expressive. Combine the Air Norton with The Tone Zone in the bridge position for a perfect blend of power and tone.
I purchased a Lyle model A690 recently from an old man in northern California who had gone blind and developed arthritis and didn't feel like playing anymore. He mentioned in passing that he had found (?) The guitar somewhere. The case was thickly covered in dust and pretty much rusted toast, but the guitar is immaculate, looks brand-new with the exception of the tuners, rusted tight. The serial is #480 so I guess its fairly old, but how old is my question? A weird aside; in the case was a handful of fender-style medium tortoise-shell picks monogrammed Eddie Kramer. Does that ring a bell for anyone? Any and all information would be appreciated! Thanks!
You don't have to use plug-ins! Some synths such as the Virus TI have very flexible effects built in. You don't have to create audio effects in your sequencer. For example, I use the Access Virus synth, which features a simple delay effect, with the added bonus that all its parameters are available in the modulation matrix. One favourite trick involves routing velocity to the delay colour parameter. For parts that get brighter with increased velocity, it adds extra animation and bite if the echoes also get brighter. Unusually, the Virus also features four-way audio panning, so you can position an audio signal anywhere between the main stereo outputs and a second pair. If the second pair of outputs is routed to an external effects unit, you can play with the concept of moving a note around in a space, where its position also determines the treatment it gets. More fun can be had by modulating reverb time and colour via an LFO. The same LFO can then be used to control filter cutoff, EQ frequency and maybe wavetable position too (if your Virus is a TI). In this way, timbral changes happen at the same time as effect changes. Paul Nagle
To ensure 100% customer satisfaction Bajaao offers 10 day return policy and we also pay for the return shipping to help you be free of the online shopping anxiety. Our content rich page is your one stop to get all the required information about the products be it the product description or the user generated hands on reviews. A friendly and knowledgeable staff is there to help you out with your queries should there be anything else you wish to know about the product, process, payment or after sale service. Our dedicated team will help you to select from the best of the products within your range. Call our experts to find out the best product to suit your style and need and buy electro acoustic guitars at the lowest prices in India.
Been meaning to try this for years.... Should have done it earlier! It really works well for me, despite a puny Atom cpu in an HP netbook and a kludged lead from an electric Ukulele stuck into the microphone socket. Yes, this lash-up can be noisy - the impedances are mismatched, the signal levels too, but a very respectable result indeed. The processing is highly effective and the presets are (of course) variable in their suitability (not every effect is ideal for a ukulele) with gems that include a really decent and surprising choice of autowah effects. Never thought I'd say that. The user interface is logical, but there is a lot of it. That's because it can do so much. Fortunately there is a 'Random' button that creates random new patches for you - keep pushing it and some fun stuff can emerge. Documentation is helpful - press F1 and have a look, it even includes hardware suggestions and hints. I intend to follow that religiously so as to get the best from this gem - and I'll be spending money to get the suggested full fat Behringer interface (~£20) from Amazon, and trying a less-compact machine with some more CPU to see if that adds to the experience. Problems? A couple of the presets do seem to crash Rakarrack - but apart from that irt has been solid. Recommended to give it a go, if you have not already done so. Both guitar an uke work well with this.
{ "thumbImageID": "Les-Paul-Studio-2018-Electric-Guitar-Vintage-Sunburst-Black-Pickguard/K35716000002001", "defaultDisplayName": "Gibson Les Paul Studio 2018 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Vintage Sunburst Black Pickguard", "sku": "sku:site51500000137386", "price": "1,649.00", "regularPrice": "1,649.00", "msrpPrice": "2,749.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Studio-2018-Electric-Guitar-Vintage-Sunburst-Black-Pickguard-1500000137386.gc", "skuImageId": "Les-Paul-Studio-2018-Electric-Guitar-Vintage-Sunburst-Black-Pickguard/K35716000002001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Studio-2018-Electric-Guitar-Vintage-Sunburst-Black-Pickguard/K35716000002001-00-60x60.jpg", "imgAlt": "" } , { "name": "Smokehouse Burst Black Pickguard", "sku": "sku:site51500000137385", "price": "1,649.00", "regularPrice": "1,649.00", "msrpPrice": "2,749.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Studio-2018-Electric-Guitar-Smokehouse-Burst-Black-Pickguard-1500000137385.gc", "skuImageId": "Les-Paul-Studio-2018-Electric-Guitar-Smokehouse-Burst-Black-Pickguard/K35716000001001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Studio-2018-Electric-Guitar-Smokehouse-Burst-Black-Pickguard/K35716000001001-00-60x60.jpg", "imgAlt": "" } ] }
×