Unlike the unit I am using here, the original units were large, AC powered, and the speed was controlled with an external pedal. Vintage Uni-Vibe pedals are very expensive at this point but fortunately we can find some very high quality reissues. Famous uses of Uni-Vibe are “Machine Gun” by Jimi Hendrix, “Bridge of Sighs” by Robin Trower, and “Breathe” by Pink Floyd.
By the way, if you like older Japanese guitars, you must obtain a copy of Mr. Noguchi’s book, ’60s Bizarre Guitars (Guitar Magazine Mooks, Rittor Music). It is lusciously printed in color and, while the text is in Japanese, model names and dates are in English, so it is an invaluable reference tool, as well as a fun coffee table book. Some of the following information on specific guitars comes from this source, as well as catalogs and other research materials kindly provided by dedicated guitar fans in both the U.S. and Japan. It’s virtually impossible to reconstruct a comprehensive chronology, but we will attempt to document some broad-brush details and periods of what guitars we can, and with luck you’ll be able to search out and identify your favorite Teiscos with much greater authority. Your corrections and additions are most welcome!
Yeah. The tremolo sound from the intro? That was four Fender Twin Reverbs. Myself controlling the speed of two of them and the producer controlling the speed of the other two. So two amps were recorded on one side of the stereo and the other two on the other side. I recorded the part on the tape without the tremolo, and then I sent the part from tape out to four amps, and he controlled two, and I controlled the other two.
I am not completely sure this tuner info is completely accurate. Sorry about that... Remember as a general rule Grovers were used on style 21 and above, and Klusons were used on style 18 and lower. There are some exceptions (like during 1940 to 1945, and pre-1930s). On pre-war Grover tuners, there are basically two types used on Martins: G-93 (round button 'butterbean') and G-98 (scalloped buttons, aka "Sta-Tite"). Both came in 6:1 and 12:1 tuning ratios, with 12:1 coming about in 1938 (and replacing the 6:1 ratio). The post-1938 12:1 ratio Grovers can be always be identified since they combine the thin seamed tuner buttons with the long pointed baseplate, and the tuner gear is screw mounted. The 1938 and prior Grover G98 tuners have a thin seamed button combined with the a square tipped baseplate, and always had the 6:1 ratio. They also had the riveted tuner gear. Ater WW2 the G98 was reintroduced with pointy baseplates and a screw mounted gear, and this was copied by Waverly, Grover, Schaller, etc after the war. Also Martin used original Waverly tuners (open back, rounded base tips, butterbean buttons) after WW2 on 00 and 000 and some D guitars style 18 (and some 28) in the late 1940s and 1950s.
Paul Reed Smith Guitars (better known as PRS) is a Maryland-based manufacturer, and relatively new in the world of guitars – founded in 1980, when they began making a series of hand-built guitars. Today they have a wide range of models, which are built in both Asia and America, as well as a full roster of artists playing their guitars; including Mike Oldfield, Dave Navarro, Carlos Santana, and Mark Tremonti.
In the 1980s, digital rackmount units began replacing stompboxes as the effects format of choice. Often musicians would record "dry", unaltered tracks in the studio and effects would be added in post-production. The success of Nirvana's 1991 album Nevermind helped to re-ignite interest in stompboxes. Some grunge guitarists would chain several fuzz pedals together and plug them into a tube amplifier.[47] Throughout the 1990s, musicians committed to a "lo-fi" aesthetic such as J Mascis of Dinosaur Jr., Stephen Malkmus of Pavement and Robert Pollard of Guided by Voices continued to use analog effects pedals.[48]
Now that we’re comfortable with the basic wiring of a guitar, we can look at some of the more popular mods. This article introduces mini toggle switches and push/pull pots, and shows how we can use these to modify a Strat in such a way as to allow use to add the neck pickup to any selection. This expands the number of available pickup combinations to 7.
{"pageName":"[mf] pdp: ibanez dt1gfm destroyer electric guitar","reportSuiteIds":"musiciansfriendprod","prop2":"[mf] shop: guitars: electric guitars","prop1":"[mf] shop: guitars","events":"event3,event50,prodView","evar51":"default: united states","prop5":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop6":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop3":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop4":"[mf] shop: guitars: electric guitars: solid body electric guitars","products":";H98107","linkInternalFilters":"javascript:,musiciansfriend.com","channel":"[mf] shop","prop7":"[mf] product detail page"}
Generic PC audio cards often don’t have ASIO drivers. However, there is a freeware thing called ASIO4ALL - Universal ASIO Driver that can turn some of the low-level game friendly Windows audio interfaces (WDM streaming) into an ASIO driver, which is better than nothing. So if you’re going to start with your guitar going direct to the PC sound card, get this next.

There are a few ways to save some money on your electric guitar (click for modal analysis). One way is to order online, for example from Amazon, which is usually cheaper than buying from a physical shop. Make sure that you know what the usual price for the guitar you want is, so that you can compare different sites, and in the best of worlds, use a discount code or wait until there’s a sale.


Electric guitar is still the most prominent instrument in rock music, and it’s a key component in many country, R&B, pop, and jazz groups. Every electric guitar player needs an amplifier because most electric guitars are barely audible without one. You’ll need one to play with other musicians, which is one of the most important ways to develop your musical skills. Because the amp is as important to a guitarist’s sound as the guitar, most teachers consider it essential to use an amp at least part of the time when you’re practicing. You can’t develop your own sound without spending some time experimenting with the controls on your amp and guitar.


Description: Body: Alder - Body Construction: Solid - Top Wood: Maple - Flamed - Neck Attachment: Bolt - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 24 - Inlay: Custom - # of Strings: 6 - Headstock: 3+3 - Bridge: Fulcrum Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Chrome, 1x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: Duncan Designed - Pickup Configuration: S-S-S - String Instrument Finish: Transparent Colors


Electric guitars are full of options, with various pickups, bridges, fret sizes, neck radii, tone woods, tuners and so on all having an impact on how an instrument plays and sounds. But stripping things down to the absolute basics, there are three types of electric guitars: solid bodies, hollow bodies and semi-hollow bodies. And they’re ideally suited for different playing approaches.

Guitar Tuners lets you tune your guitar in seconds for free using a microphone so that you guarantee the perfect pitch of your instrument every time. Just play a note, and Guitar Tuners will display which note you''re playing, and how close you are to having that note in tune. The needle on this Guitar Tuner will turn blue you have an exact match. Just play each note on your guitar (E, A, D, G, B, E) or other musical instrument, and get in tune !



Where you let the overdrive or distortion fill out the tone generated by only three notes. Mess around with different pairs of notes and you'll soon find what sounds good with distortion and what sounds harsh and dissonant. A simple root fifth octave triad is the bread and butter of overdrive and distortion playing. Sometimes if you have a lot of gain on a hot distortion setup you may need to roll off the highs a bit as the high end harmonics can get a bit too brassy on top and harsh on your ears. Have a blast.
You’ll need to get yourself setup with an account on some of the web stores selling components such as effects pedal specialty stores listed above, and some general component stores such as Mouser and Digikey. AMZ provides a list of the components required for each project. Make sure you check carefully the component requirements such as type of capacitors. Many components may have suitable electrical values but different physical layouts, so use the datasheets for your chosen component. Measure the spaces and holes on your PCB to make sure the components will fit. Remember that you’ll also need an enclosure in which to install the finished circuit and don’t forget things such as knobs, battery holders etc.
The AS is a semi-acoustic guitar built to tackle just about any genre of music you throw at it. The pickups are mounted into a sustain block for increased sustain and feedback elimination. The 17th fret joint features comfortable access to higher notes. Super 58 Custom Pickups The Super 58 Custom pickups deliver the smooth, nuanced tones and the biting growl of blues. Ebony Fret board w/ Art star Fret Edge Treatment The Ebony fret board with Art star fret edge treatment provides tight response and smooth left-hand fingering. Bone Nut The Bone nut provides richer tone from low to high. Specifications: neck type: Art star 3pc Mahogany/Maple set-in neck body: Flamed Maple top/back/sides fret board: Bound Ebony fret board w/Pearl & Abalone block inlay frets: Medium frets w/Art star fret edge treatment bridge: ART-1 bridge tailpiece: Quick Change III tailpiece neck pu: Super 58 custom (H) neck pu bridge pu: Super 58 custom (H) bridge pu Neck Dimensions: Scale: 628mm/24.7" a: Width at Nut - 43mm b: Width at Last Fret - 57mm c: Thickness at 1st - 20mm d: Thickness at 12th - 22mm Radius 305mmR Body Dimensions: a: Length - 19 1/4" b: Width - 15 3/4" c: Depth - 2 5/8".
Electronics installs are one of my favorite jobs here at the shop and this project was one of the funnest.  Installing a Clapton pre-amp is more then just a quick wiring job because of the surface mount board.  The board needs to be routed into the body underneath the pickguard.  Setting up the router is the most time consuming part of this job and once the routing in complete the actual wiring takes only a few minutes.  The guitar was then topped off with a fret level and setup. -Evan
The tone from a Bourgeois produced with master grade Cocobolo wood using hot hide glue is superior to any guitar I have played, I can get an incredible reverb sound by applying a light percussion on the body with my forearm, this guitar is expensive but worth it. I believe Bourgeois builds 400 guitars per year, the other major producers production is 400 guitars per week.
This is a no brainer, but a value that must be considered before any purchase no less. As mentioned above, your abilities on the instrument will likely affect the price range you’re looking at, which may have an effect on the brands you shop within as a consequence. For instance, if you’re not looking to buy a high end guitar, you probably won’t even bother testing out a Gibson, as their guitars will likely be out of your range. The reverse is true as well, an experienced player on the market for high end tone probably won’t be satisfied by many of Yamaha’s offerings.

2. Orange Micro Dark w/1x8 Cabinet ($288): Who doesn’t love tiny yet mighty lunchbox amps and the speakers they rest upon? The Micro Dark head uses a tube front end to push 20-watts of power and coupled with a 1x8” speaker, you’ll be able to get awesome tube tone for a fraction of the price and size of a bigger rig. This little duo is well-equipped to handle clean and overdriven tones whether you are cracking the volume on the speaker or playing through your headphones.
What we consider as standard size today were not so standard back in the '30s. Back then the "parlor guitar" or "blues box" was commonly used, with its compact body and mid-emphasized tone. Many artists used this instrument to shape many of the musical styles that we have today. The L-00 Standard from Gibson captures the iconic "blues box" faithfully for today's players, adding in their premium touch and modern tech that results in a true timeless museum quality instrument.
A compressor acts as an automatic volume control, progressively decreasing the output level as the incoming signal gets louder, and vice versa. It preserves the note's attack rather than silencing it as with an Envelope Volume pedal. This adjustment of the volume for the attack and tail of a note evens out the overall volume of an instrument. Compressors can also change the behaviour of other effects, especially distortion. when applied toward the guitar, it can provide a uniformed sustained note; when applied to instruments with a normally short attack, such as drums or harpsichord, compression can drastically change the resulting sound. Another kind of compressor is the optical compressor which uses a light source (LED or lamp) to compress the signal.
The Ibanez Tube Screamer is the industry standard for overdrive pedals. Kicked into legendary status by the late great Stevie Ray Vaughan. The Tube Screamer TS808 was first released in the late 70’s and now catches a small fortune on the vintage market but fortunately there are reissues and many boutique clones out there. The Tube Screamer is not the only overdrive circuit of course, there are many excellent options, it is just clearly the most famous. What makes the TS so cool is the way it interacts with an already overdriven amplifier. It can add a nice amount of gain, sustain, and tonal shaping options. They do provide a bit of a boost in the mid frequencies that many people love as it helps to cut through a band. The list of TS users is extensive but Stevie Ray is the most notable.
While most collectors aren’t necessarily going to boast that they own a number of Harmony guitars, we shouldn’t forget the important “first axe” role Harmony played for many guitarists. This company took mass production of guitars to the next level. And though you may have to sort through a few to find one that is completely intact and doesn’t allow a car to drive under the strings, they were quality-made instruments for the most part. For those of you who first learned on a Harmony Archtone, this is certainly a childhood treasure!

{"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: davison","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","prop17":"sort by","evar51":"default: united states","prop10":"brands","prop11":"davison","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
This is such a trite discussion. There are many more choices than Fender and Gibson, and to boil it down to those two players is detrimental to the industry and by extension musicians of all skill levels. Those companies made great innovations and came out with classic models, and the industry owes them a whole lot. But to me, you get more points for continued innovation, not making a few great models then resting on laurels for the next 100 years.
The beauty of an affordable small amp is that it can be high quality without the sacrifice of anything. I mean yeah some people say that the low tones disappear a little when the amplifier gets small, but don’t listen to them too much. Unless your low tones are being drowned out by some loud person screaming into the microphone so hard that the system starts screeching, even the smallest of amps can produce a respectable low tone. The small amplifiers are there to be portable and easy to have, so that you never have to deal with a back hurting (unless your instrument is heavy) or your arms being tired from anything other than playing the guitar too much. Which is why the Blackstar Fly 3 Battery Powered Guitar Amplifier is a great piece of equipment to have in your artillery. Portable, small and powerful in sound, what else could anyone ever want?
On the extreme end of things, adding a lot of reverb to your tone can create large, expansive soundscapes where the notes are less distinct and everything forms one carpet of background sound. Reverb pedals often have a number of controls, from the most basic knobs controlling the volume of the effect (known as “mix”, or how much reverb is mixed into your guitar signal) and the length each note reverberates for (known as “decay”), to more versatile pedals that have controls for different kinds of reverb such as “small room”, “plate” and “arena”.
Most modern effects use solid-state electronics or computer chips. Some effects, particularly older ones such as Leslie speakers and spring reverbs, use mechanical components or vacuum tubes. Effects are often used as stompboxes, which are typically placed on the floor and controlled with footswitches. They are also built into amplifiers, tabletop units designed for DJs and record producers, and rackmounts, and are widely used as software VSTs.
JSL, I agree with you on the Mayer comment. Any one who is bashing him needs to listen to his latest live album. kid rips plain and simple. I have to disagree with you on the Van Halen comment, not that he isn't a great player, but to me his playing always lacked substance, no soul to it. Now, I can't stand Clapton, (I won't get into why), but he should definitely be on the list.
The electric guitar was at the heart of popular music for the new generation. Fender released the Telecaster – the first mass produced solid body electric which made it possible for the average Joe to buy a guitar and start a band to express themselves.  With amplifiers and solid body electrics the volume could be cranked and every bit of emotion displayed through the music.
© 2013 Ubisoft Entertainment. All Rights Reserved. Rocksmith logo, Ubi.com, Ubisoft, and the Ubisoft logo are trademarks of Ubisoft Entertainment in the US and/or other countries. The “PS” Family logo and “PS3” are registered trademarks and the PlayStation Network logo is a trademark of Sony Computer Entertainment Inc. Software platform logo (TM and ©) EMA 2006.
Launch price: $799 / £826 | Body: Alder | Neck: Maple | Scale: 25.5" | Fingerboard: Pau ferro (rosewood reviewed) | Frets: 21 | Pickups: American Vintage '58 Single-Coil Tele, American Vintage '52 Single-Coil Tele | Controls: Volume (with S-1 Switch), tone | Hardware: 3-saddle American Vintage strings-through-body bridge | Left-handed: No | Finish: Faded Sonic Blue, 3-Color Sunburst
The Fuzz-Tone connection hints that we need to look further back, and across the pond, for earlier examples of recorded guitar distortion. Gibson, and hence Maestro, was given the circuit that became the Fuzz-Tone by studio engineer Glen Snotty. Snotty, in turn, had devised the transistorized fuzz-generating design to replicate the sound that occurred when a tube preamp in the channel of a mixer he was using to record Grady Martin’s short-scale bass solo for the 1961 Mary Robbins hit record ‘Don’t Worry’ started to fail and yield a distorted tone. Whoever decided to stick with the track rather than re-record it through a properly functional channel was on to something; the result was Nashville’s first recorded fuzz guitar (a Danelectro bass, in fact). Courtesy of Maestro, Snotty’s fuzz circuit soon made the trendy new sound available to the world.
Few guitarists play slide guitar with more raw emotion or feeling than blues legend Muddy Waters. There’s perhaps nobody more important to the electric blues idiom, of which Waters became the primary spokesman. His playing was raw, dirty, raunchy, and everything else that makes the blues as great as it is. He undoubtedly inspired every great blues guitar player that came after him.

You’ll find a full slate of dedicated bass stompbox effects as well as many multi-effects pedals and processors. Like their guitar-friendly cousins, bass effects offer most of the same tone shaping capabilities, including chorus, reverbs, delays, phasers, and tremolos. Because of the bass’s unique sound dynamics that reach deep into the lower frequencies, many bass effects are focused around compression and limiters that help keep a lid on destructive subsonic sound waves that can damage gear. Typically, many guitar effects are not optimal when used with a bass.
Okay, choose from the best electric guitar brands to suit your needs and look great too with this helpful guide for guitarists of all levels! Would you rather get the proven model, or trust a relatively unknown brand? This is especially true for those who are looking to buy their first instrument. With that in mind, we have compiled a list of top 10 electric guitar brands which you can trust. We will talk about each, and explain why they are the best guitar brands. On top of that, we will mention some models which we have had the chance to handle in the past.

Acoustic amplifiers produce an uncolored, "acoustic" sound when used with acoustic instruments with built-in transducer pickups or microphones. The amplifiers often come with a simple mixer, so that the signals from a pickup and condenser microphone can be blended. Since the early 2000s, it has become increasingly common for acoustic amplifiers to provide a range of digital effects, such as reverb and compression. As well, these amplifiers often contain feedback-suppressing devices, such as notch filters or parametric equalizers.[22]
by pedalhaven This little board from  @andshamlian  is so sick! Don't forget to DM/Tag us to submit your photos! ▪️ ▪️ ▪️ ▪️ ▪️  #pedalhaven   #pedalboard   #guitarpedals   #knowyourtone   #ambienttones   #pedalboards   #pedalnerds   #pedalporn   #guitar   #gearporn   #gearnerds   #pedalboardpeople   #shoegaze   #geartalk   #guitarsdaily   #gottone   #tonefordays   #guitargear   #reverb   #gearpost   #boardshot 
Prior to dennis, i had never taken guitar lessons. Always tried to teach myself. I struggled since i had no structure, i would consistantly get lost, which would make me put the guitar down due to frustration. Deciding to hire dennis was a break thru for me, and honestly wish i would have looked into it much sooner. Not only has my skills progressed, which they due weekly at a much faster rate then when i was trying to learn on my own, but my confidence and motivatation has increased greatly. I look forward to meeting with dennis each week and building off of what he taught me the previous week. The amount of patience dennis has is great, and the way he explains different things so that i understand is awsome. Would definetly recommend dennis to anyone, whether they have just purchased their first guitar, or they have tried numerous times to teach themselves, or even if you have alot of the basics down, but looking to take your knowledge and playing to the next level.
Excellent article. I have found that is a complete waste of time trying to convince guitarist of anything contrary to what they already believe about instruments. The level of passion for the “wood doesn’t matter” camp is truly astounding. We are not testing a new drug or solving cold fusion. The question is simple, does wood make a difference in the tone of an electric guitar? Intuitively, it would seem strange if it didn’t; but, there are many factors that are going to affect the sound produced from a guitar; isolating them is as difficult as creating a study that will convince anyone of an idea they already are clinging to. I think this is a pretty good experiment, better than most I have seen. In the end though, who cares?…really. If someone would like a guitar made out of a Formica counter top…go for it, locking tuners, the pickups and strings of your choice…you’ll be ready to rock. And won’t you be the clever one? As for myself, my opinion, musical instruments have character, a soul if you will. That character comes from the material it is made out of and the craftsman that made it. There is no object more alive than a musical instrument. For arguments sake, lets grant the “wood doesn’t matter” their entire argument. I’d still buy the korina instrument over the countertop. And like most stubborn asses who play guitar, you won’t convince me otherwise.
Epiphone introduces the Les Paul Special VE (Vintage Edition) electric guitar featuring the classic Les Paul profile with a lightweight Poplar body. The Les Paul Special VE is powered by Epiphone Open Coil humbuckers and is available in beautiful “Vintage Worn” color finishes.For decades, the Les Paul Special has been one of Epiphone’s best se...  Click To Read More About This Product
But what about the Les Paul devotees like Jimmy Page, Zakk Wylde and Bob Marley? Is it possible that the Les Paul is as enduring and adaptable as the Strat? Um… Yes! Each guitar style has its own rich history of players and possibilities, and with a powerful imagination, anything is possible. Solid body guitars are truly the dominant species of electric guitars for their overall versatility, ability to interact with pedals and amps, and general lack of fussiness.
I always say that Jose Feliciano? is indeed one of the greatest guitarists that’s ever lived. Flamenco, latin, bolero, classical, rock ect ect…. You name it and Jose can play it. Why he’s not on Rolling Stone’s 100 greatest guitarist of all time, is beyond anyone’s guess. dont believe me look up on youtube purple haze, the thrill is gone, flight of the bumble bee, Malagueña under Jose Feliciano. the guy can play anything and make it his own.
Trim:  Heel cap: ebony. Fingerboard: ebony bound in white celluloid with scalloped lower end; 24 frets under A and D, 21 nickel-silver frets under G and C; single abalone dots behind 5th, 7th, 9th, 10th (slightly larger), and 15th frets; double mother-of-pearl dots behind 12th fret. Nut: bone. Bridge: mahogany capped with ebony; nickel-silver-plated steel screws to adjust bridge height and pickup contact. Tuners: six nickel-plated steel, worm-gear machine tuners by Grover with convex head surfaces and decoratively cut plate outline. Endpin: black bakelite; extends through tailpiece. Pick guard: imitation tortoise shell plastic raised on wood brace affixed to top with two steel dome-headed screws. Lacquer: dark orange-brown sunburst.
The guitar, however, appears to be in better shape than the guitar maker. While in the past decade, sales of the electric guitar have fallen from 1.5 million to 1 million, according to the National Association of Music Merchants (NAMM) a total of 2.6 million guitars, including both acoustic and electric guitars, were sold in the U.S. last year, 300,000 more than in 2009.
The next step is to figure out what gauge, or thickness of string is best suited to your playing ability and style. Thinner gauges are easier to fret and bend, and may be better suited for beginners, until callouses build up on the fingertips. Heavier strings tend to produce greater volume and fuller tone. Nylon strings are typically categorized as light, medium or heavy tension. Steel strings for both electric and acoustic guitars are categorized by the gauge, or thickness of the lightest string, the high E string, measured in thousandths of an inch, with .09 being a common size for an electric set. A set of electric strings may be labeled .09-.042 - this is the gauge of the lightest and heaviest string in the set. Acoustic sets are a little thicker, so a typical medium-gauge set might be .012-.054.
Modulation, in general electronics, means the altering of signal strength. In audio devices, modulation is a control feature that varies the strength of some effect over time to alter tonal properties. Some modulation effects mix ("modulate") an instrument's audio signal with a signal generated by the effect called a carrier wave.[70] Other modulation effects split an instrument's audio signal in two, altering one portion of the signal and mixing it with the unaltered portion.[71]

DRILLING THE HOLES Now is a good time to drill the holes for the neck, pick up rings, bridge, string furreles, the control plate and cavity. Here is where I wish I had a drill press but I don't, so I just use a hand held drill. It doesn't matter wher you start drilling you holes, just make sure you use the right size bit for the screws that you will put in them later. To figure this out I compare the thickness of the screw minus the threading. A good rule of thumb is to start off with a bit that will produce a hole that is smaller than the screw. If the hole is too small when you try to screw in the screw then you can move up to the next size bit an re-drill. Be careful of the depth that you drill you hole to as well. A good way to do this is to size up the screw with the bit and mark the bit with a peice of tape. This will help you to keep from going to deep.


The problem of the recent Gibson bashing is well-founded. There were quality issues over the last maybe 15 years. The thing is that a Gibson is still a dream for a lot of people. They get better and giving themselves a present after putting money away. Then, after several years, maybe decades of anticipation they get crappy quality for several thousand dollars. The brand is alive, they can bounce back, but the managment...instead of the elevator, they should take the japanese business shortcut. As soon as the quality and passion is back, people will love to buy one. Hope they'll get back on track before 2020. - MountainGoat

Mic placement is pretty crucial. You can get a million different EQ responses depending on where you throw the mic in front of the cab. I personally have the best luck - or at least I think so - when I back the mic off a little bit. I know a lot of engineers throw it right on the grille to get the bass boost, the proximity effect and all that garbage, but I find that if I back it up about six inches, I get a more balanced EQ curve.
MMh, for years I had a tone control in my Framus ES copy that followed a similar combo idea. I got it from the Rockinger.de site and it might have had a Bill Lawrence conncetion. (Have you tried his q-filter?) It replaced the cap with an inductor AND had the other end of the sweep connected to a regular, but smaller, cap. So you could go either thick tone or thin, but you could not bypass it all. That would have required an extra switch.
My visit to NAMM showed me that we’d definitely find at least a couple of good beginner’s amps for less than $100, so we decided to make that our price ceiling for this test. That’s enough to buy an amp loud enough to play with a small combo, compact enough to fit easily into a small bedroom, and light enough for kids to carry. Beginners don’t need more than that. And when you consider that most people who take up a musical instrument don’t stick with it long, it’s wise to limit the expenditure until one really needs a larger or more fully featured amp.
By contrast, tuning (or pitch) correction processors and plug-ins are normally considered processors rather than effects, but they do have creative uses. The idea behind these devices is to monitor the pitch of the incoming signal, then compare it to a user-defined scale, which can be a simple chromatic scale or any combination of notes. Pitch-shifting techniques are then used to nudge the audio to the nearest semitone in the user's scale but, because the amount of pitch-shift required is usually quite small, the result doesn't sound grainy or lumpy, as often happens when large amounts of pitch-shift are generated. Because pitch tracking is used to identify the original pitch, only monophonic signals can be treated.
This is a rare bird. Its a early ibanez maxitone 994. It has a huge neck but plays pretty great! It has that classic MIJ tone. I can include a new Gator case for $50 extra! The neck and frets are good! The electronics are a little dirty. Ill clean them the best i can, but i thoughtit worth mentioning. It is functioning as it should be just a little dirty!

Martin flat top guitars were made in various sizes. The bigger the guitar body, the better and more collectible the guitar. This is why guitar body size is so important to identify on a Martin flat top guitar. Starting in October 1930, Martin stamped the guitar body size right above the serial number inside the guitar. This makes identifying body size on October 1930 and later guitar very easy. For flat top guitars made before October 1930, the easiest way to figure out the body size is to use the flat top guitar body size chart below. Body sizes, pretty much from smallest to biggest, include O, OO, OOO, OM, D.
The way you fix this is by finding a book that makes you reconsider an aspect of your playing, regardless of what that is. If you’re into metal go ahead and pick up a book on Gypsy jazz. If you’re a dedicated Bluegrass flatpicker try your hand at learning some jazz. If you learn one thing from a different genre that you can routinely apply to your genre of choice you can break yourself out of just about any rut imaginable.
In typical pedal effect chains you will most likely be running cable lengths that are much longer than 5.5 meters. The ME-80 allows you to keep your tone pure when running lots of effects. You can run a cable up to 5.5 metres into the input of the ME-80. The multi effects engine processes up to 8 effects in its internal signal chain. Then the ME-80 outputs your guitar signal as a 2,000 Ohm low impedance signal allowing you to run a much longer cable to the amplifier.
The Fender Stratocaster Squier is possibly the most recognizable shape in electric guitar history. The Fender Stratocaster design is mimicked by manufacturers all over the world. Fender produces its own line of budget “Strats” called the Squier series. If you want to start with an electric guitar, chances are you’ll buy something like this for around $130 USD.

No doubt many of you thought that the very first electric guitar was Les Paul’s legendary “Log.” Well, regardless of who was responsible for its invention and evolution, electric guitarists throughout the world are truly grateful for the ability to amplify their instruments, as are their audiences. This capability to connect to dedicated guitar amps along with the use of distortion and guitar effects has spawned entirely new genres of music. Pickup types and configurations, as well as specialized switching options and tone controls also help generate different sounds. But when you break it down to the basics, there are really only three types of electric guitars in existence to this day, excluding acoustic-electrics - the aforementioned Hollow Body, Semi-Hollow Body, and Solid Body varieties.


DR Strings makes strings that were specifically designed for drop d tuning, other alternate tunings, and even standard tuning. Known as DDT strings, DR spent over two years perfecting them. DR created a new patent pending method for constructing these strings to ensure great performance with lower pitches. Because of the amazing construction, and their ability to quickly lock into tune so quickly, DR calls their DDT's "Superstrings". Why not try a set? DDT's are available for electric guitar or bass guitar.
Wildwood Guitars is proud to be recognized as one of nine authorized online Gibson dealers. We invite you to browse our extensive inventory and discover the magic of one of the greatest American brands of all time. Located in the heart of Tennessee, the Gibson Memphis factory is known for crafting the majority of Gibson’s incredible semi-hollow and hollowbody instruments. These guitars are overflowing with the soul of the city they’re born in, and they represent the ultimate in both vibe and versatility.
SHEILDING Sheilding is good to use if you want to minimize that annoying buzz you can get from surrounding interference that electronic components such as amps can produce. You can use sheilding paint that is a bit more expensive but easier to apply than copper tape. All you do is paint it on and let it dry. It also gets into the areas tape can't reach. To install the tape you basically just apply it to the inside of the control cavity and solder up any seams that might let the interference through. The soldering can be a little tricky since you have to lay down a long bead of it along the seam. Kind of like welding. Here are some futher instructions After this is done you can install the pots and switch. Be careful when tightening them down not to scratch the finish. Add the knobs and get out your schematic for wiring it up.
It was a great guitar to learn on, but you are ready for a serious gigging guitar.  Okay, if she was your FIRST love then don't dell her, keep her around for inspiration (plus she ain't worth any money anyway).  Do NOT upgrade her.  Once you start, there will be no end.  Sure great pickups will make her sound great, but you'll also want to replace ALL the electronics, and the tuners, and the bridge, and... well, you get the idea.
Another relatively drastic but easy and cheap way to hot-rod your guitar’s sound with its current components is to alter how and where its volume and tone pots are connected to each other. The difference can be subtle—and it’s more a matter of preference than what’s “correct”—but it can make the difference between a guitar that is just OK and one that really is a joy to play.
If you have your heart set on a Stratocaster, but can’t justify shelling-out $600 or more for the USA-made Standard Strats, the Squier Standard Stratocaster is a great place to start. Unlike the even cheaper Strats that are included with Fender’s “starter packs,” this guitar is a definite step-up in quality and features a more modern take on their traditional bridge. I personally prefer this bridge style over Fender’s traditional/vintage 6-screw bridges.
Several years later, Gibson issued its third Jimmy Page Signature guitar, this one based closely on Jimmy Page’s #2. Issued in a production run of 325 guitars, the guitar more accurately reproduced Page’s heavily modified No. 2 than the original Signature model of the 1990s, and featured the 4 push-pull pots, the two mini-switches under the pick guard, accurate tuners and sound-accurate pickups (the same pickups that were used in the 2005 Jimmy Page No. 1 Signature), as well as an accurate neck profile. As in the original Signature model of the 1990s, pulling up the neck or bridge volume pots switched the respective pickups’ coils from series to parallel, and pulling up the tone pots switched the respective pickups from humbucking to single coil. The two push-button DPDT switches mounted beneath the pickguard provide universal switching functions, regardless of the positions of the push-pull pots. With the switch mounted toward the bridge-end of the pickguard in the out position, the bridge pickup’s phase is reversed. With the switch mounted toward the neck-end of the pickguard in the out position, both pickups are wired in series and out of phase. With both switches out, both pickups are in series and in phase. The Jimmy Page “Number Two” Les Paul is finished with a sunburst finish to replicate the appearance of the original guitar. 325 of these guitars were made, with the initial 25 being autographed by Jimmy Page and priced at US$25,000 when new.
Every single pickup on this Godin XTSA is awesome in its own right, but the best part of it all is dialing ina combination of the two. By virtue of its quality, it gives plenty of power, possessing a wonderful sounding high end cutting through, which makes it possible for you to hear it over the keyboard and the bass. With this electric guitar, you can get a beautiful acoustic sound and a really fat and great sound as well.
{ "thumbImageID": "MM100-Mini-Double-Cutaway-Electric-Guitar-Blood-Red/J37216000003000", "defaultDisplayName": "Mitchell MM100 Mini Double Cutaway Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Blood Red", "sku": "sku:site51500000010548", "price": "79.99", "regularPrice": "99.99", "msrpPrice": "149.99", "priceVisibility": "1", "skuUrl": "/Mitchell/MM100-Mini-Double-Cutaway-Electric-Guitar-Blood-Red-1500000010548.gc", "skuImageId": "MM100-Mini-Double-Cutaway-Electric-Guitar-Blood-Red/J37216000003000", "brandName": "Mitchell", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/MM100-Mini-Double-Cutaway-Electric-Guitar-Blood-Red/J37216000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51500000010547", "price": "99.99", "regularPrice": "99.99", "msrpPrice": "149.99", "priceVisibility": "1", "skuUrl": "/Mitchell/MM100-Mini-Double-Cutaway-Electric-Guitar-Black-1500000010547.gc", "skuImageId": "MM100-Mini-Double-Cutaway-Electric-Guitar-Black/J37216000002000", "brandName": "Mitchell", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/MM100-Mini-Double-Cutaway-Electric-Guitar-Black/J37216000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Walnut Stain", "sku": "sku:site51500000010546", "price": "99.99", "regularPrice": "99.99", "msrpPrice": "149.99", "priceVisibility": "1", "skuUrl": "/Mitchell/MM100-Mini-Double-Cutaway-Electric-Guitar-Walnut-Stain-1500000010546.gc", "skuImageId": "MM100-Mini-Double-Cutaway-Electric-Guitar-Walnut-Stain/J37216000001000", "brandName": "Mitchell", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/MM100-Mini-Double-Cutaway-Electric-Guitar-Walnut-Stain/J37216000001000-00-60x60.jpg", "imgAlt": "" } ] }

The new generation of ‘boomers’ as they were known, thrived with the growing push on consumerism.  This of course included buying records and with the pin ups of Rock and Roll like Elvis and Chuck Berry – they felt part of a new movement which understood them and related to their struggles, such as growing pains, responsibilities and fitting in with society.


A significant cosmetic change occurred in Japan in ’65, which can help determine dates. Previously, almost all models had plastic pickguards. In ’65, most models switched to striped metal guards, with the alternating matte stripes etched into the metal. Thus, if you find a guitar Teisco with a plastic guard, it’s probably from ’64 or early ’65. If it has a striped metal guard, it’s probably from ’65 or later.

While SG Guitars kits are sold in a number of different timber varieties, if you are looking to match the original as closely as possible you will be best selecting a model constructed with a Mahogany body and Maple neck with Rosewood or Ebony fretboard. * Gibson has recently transitioned from Rosewood to Richlite due to New CITES Regulations For All Rosewood Species.


If you are inexperienced, it is only recommended that you attempt to setup a guitar that is of little value to you, both financially and sentimentally. If you don’t have one that fits these requirements, then it is best to pay the cost of a guitar setup as performed by a professional. The primary risk while setting up the instrument is over adjustment. Working any part of the bridge too much will cause wear and tear, and irreparable damage to the neck is often the result of improperly adjusting the truss rod. It is always hard to justify ruining a perfectly good instrument in order to avoid guitar setup cost.

When speaking of electric guitars and pickups we are usually talking about magnetic pickups, as they use magnets to convert the vibration of the string into an electric signal, and these can be divided into 2 main types: The Humbucker (Double-coil) and the single coil pickup. Double-coil pickups are basically single coil pickups mounted side by side and the sound they pick up is "integrated" through to the output.
When the Fender company invented the first widely produced electric bass guitar (the Fender Precision Bass) they also developed a bass amplifier, the Fender Bassman, first produced in 1952. This was a 26-watt tube amplifier with a single 15" speaker. In 1954, the Bassman was redesigned to use four 10" speakers. This speaker cabinet was an open-back design; as such, it had poor low-frequency efficiency and was prone to blowing speakers when used for bass because of the lack of damping. Somewhat ironically, it became very popular as an electric guitar amplifier. The circuit design also underwent repeated modifications. The "5F6A" circuit introduced in 1958 is regarded as a classic amplifier design and was copied by many other manufacturers, such as Marshall.

UPDATE 10/21: The good news first - I'm still absolutely loving the game and steadily improving. I'm only able to play about one to two hours a day, but even though that's all the time I'm able to put in, I'm already to the point of being able to play along with a song. But (here comes the downside), with my improvement audio lag has become a real issue. Before I was so horrible that I couldn't hit the right notes at all, let alone on time, so it didn't make much difference. But now that I've improved, it's a problem. To be fair, they warn you about this in the form of a pamphlet inside the game box, so it wasn't out of nowhere. I was just hoping that since I wasn't using HDMI, the lag wouldn't be too horrible. Wrong.
Let’s get it straight. Froo – Shawn – Tey. If you don’t know him, he’s the lead guitarist of the Red Hot Chili Peppers. Frusciante is the author of the brilliant chord progression on Under the Bridge, the haunting intro to Californication and the simplistic solo and riff on Otherside. If you’re the casual listener of the Chili Peppers, then you may wonder why John has made it so far up this list. But a tad of a closer look will reveal that his simple catchy riffs are the tip of the ice berg. One can catch a glimpse at his technical skill in the Dani California solo. A bit deeper and you’ll run into Lyon 06.06.06 in one of the B Sides. John takes his influences (Page, Hendrix) and mixes his own nuances into a sound that’s pleasantly different, but melodically having the same effects on you. A track to look out for on his solo work – Ramparts – showcasing four or so guitars layered upon each other in an introspective orchestra.
Interestingly, the neck is crafted from maple, topped by a 20-fret walnut fingerboard which complements the back and sides nicely. Following the specs of older Gibson guitars, the scale length is shorter at 24.75", while the nut width is 1.725", which gives the instrument a comfortable playing feel. Adding to the already good vale of this guitar is the built-in LR Baggs Element electronics for stage performance, with discrete soundhole mounted volume control. If you are looking for a handcrafted workhorse acoustic guitar that will not break the bank, then check this out.
The Ibanez Artcore AS53 is a semi hollow-body guitar created for guitar players from diverse genres as blues, country, rock and jazz. The guitar feels nice and has a compact and comfortable body. The tone is rich, warm and full. If you are looking for that fat hollow body sound, this guitar makes it possible to switch from jazz to every semi-hollow rocking style of music. A combination of quality and affordability.
One glance at this bad boy reveals just how accurate it is to the 1959 version. We are talking exact same tubeless truss rod assembly, aniline dye, exact same finish... everything. In terms of hardware, they went with a set of Klauson Deluxe tuners and period specific Tune-o-Matic bridge. The custom humbuckers were coiled and voiced to perfectly match the original PAF design from the late '50s which was done using Alnico III magnets and 42 AWG wire. The performance of this guitar is an experience that is rarely found out there.
We've watched Dan Erlewine repair this 1930s Kay over the previous 3 Trade Secrets. It's time to finish it up. Elliot John-Conry of EJC Guitars ages Dan's patch of new plastic binding so it blends in with the old binding around it. About the guitar in this video: This 1930s Kay Deluxe is a fixer-upper that Dan Erlewine repaired in order to sell. Now that it's in great shape again, maybe Dan'll keep it!
Flat tops from 1945 to 1969 are considered good quality and have good sound, although they are not as collectible as the 1920's to 1944 steel string models. This is largely due to the change in bracing and materials Martin started using in 1945. Rosewood models of Brazilian rosewood are most collectible from this era. This is because Brazilian rosewood was basically unavailable since 1970 due to export problems. Because of this, these models are considered more collectible.
What about Esteban?….lol. There’s no way to make a top ten list, as there are so many extremely talented players. Glenn Campbell is an outstanding guitar player. Lee Roy Parnell is second only to Duane Allman as far as that style of slide playing. Although Willie Nelson doesn’t shred, he is an incredible talent. Duke Robillard, Danny Gatton, Robbie Robertson, Steven Stills, Alvin Lee, Tony Rice, Bryon Sutton, Brian Setzer… there are so many wonderful incredibly talented musicains….thank God! It would suck if everyone played the same. Variety is the key…learn to truly love the art of music. Just like blonds, brunettes and redheads they are all wonderful! If you even try to list the top ten of anything, you are only shortchanging yourself.
STEM educators will take part in an intense five-day electric guitar design/build institue. Each faculty member will build his/her own custom electric guitar and will engage in student centered learning activities that relate the guitar design to specific math, science and engineering topics. Participants leave this weeklong experience with their custom-made guitars, curriculum modules with short term assessments that can be immediately integrated into the faculty team school curriculum.

I just purchased a Lyle acoustic guitar in excellent condition. It's Serial # 204 and Model # 712. The top of the guitar says Lyle with a gold cross-like design up by the tuning keys. It looks like it was painted on the wood by the manufacture. The top tuning key head and neck are the color of milk chocolate with pearl-type fret inlays. The body of the guitar is a light tangerine color showing the natural wood grain under the clear lacquer finish. It has a dark chocolate bridge, and a black pick guard with a white pearl engraved inlay of a floral sprig or vine-type design. There is a set of three circles around the center opening (1 thin black line, a wide band of black and white lines and another thin black line. It has light tangerine and milk to dark chocolate stripped sides and back which is the natural wood grain showing through the clear lacquer finish. JAPAN is engraved on the back of the tuning key head in back.

The full-size Davidson guitar features a maple fretboard consisting of strings that sound very pretty good once you have tune it right out of the box. This Davidson full-size electric guitar comes with die cast tuners designed to keep it in perfect sound shape, followed by a practice amp having an overdrive body, which makes the practice exercise easy and fun-filled. The amp can be tuned with an iPhone App and by the time you set this baby to work, you will surely get your neighbors screaming for the peace.
There’s a common belief that certain strings are better for beginners than others. While nylon strings can be easier on beginner’s fingers, the main thing that matters when it comes to guitar strings is the style of music you are planning to play, because the difference in feel and sound between the two materials is significant – even for a beginner.

Guitar distortion is obtained and shaped at various points in the signal processing chain, including multiple stages of preamp distortion, power valve distortion, output and power transformer distortion, and guitar speaker distortion. Much of the distortion character or voicing is controlled by the frequency response before and after each distortion stage. This dependency of distortion voicing on frequency response can be heard in the effect that a wah pedal has on the subsequent distortion stage, or by using tone controls built into the guitar, the preamp or an EQ pedal to favor the bass or treble components of the guitar pickup signal prior to the first distortion stage. Some guitarists place an equalizer pedal after the distortion effect, to emphasize or de-emphasize different frequencies in the distorted signal.
The C7’s back, fretboard and bridge are all rosewood, which makes for a stunning color contrast with the spruce. The strings are Savarez Cristal Corum, in high tension (500CJ), but according to one professional guitarist, the action is very easy no matter the tension, so a beginner should have no problems starting out on this model. Even someone who’s played a good while but simply wants something they can “jam” on whilst out on a recreational road trip, or play on a small-gig basis, will love the Cordoba C7 spruce-top.
AGE CAN’T HINDER YOU – Working off of muscle memory and visual assistance, ChordBuddy is designed for players of every age. In fact, ChordBuddy is well-suited for those looking to play guitar with arthritis, offering a pain-free method of playing your favorite song. Utilizing ChordBuddy also allows you to learn the guitar on your own, eliminating the need for long guitar lessons with an instructor, which can result in prolonged joint pain.

{ "thumbImageID": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "defaultDisplayName": "Gibson Les Paul Faded 2018 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Worn Cherry Black Pickguard", "sku": "sku:site51500000137380", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard-1500000137380.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Cherry-Black-Pickguard/K35713000002001-00-60x60.jpg", "imgAlt": "" } , { "name": "Worn Bourbon Black Pickguard", "sku": "sku:site51500000137381", "price": "989.00", "regularPrice": "989.00", "msrpPrice": "1,649.00", "priceVisibility": "1", "skuUrl": "/Gibson/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard-1500000137381.gc", "skuImageId": "Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001", "brandName": "Gibson", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Faded-2018-Electric-Guitar-Worn-Bourbon-Black-Pickguard/K35713000001001-00-60x60.jpg", "imgAlt": "" } ] }


If ever there were a forensic investigation to identify the true biological father of punk rock guitar, all DNA evidence would point clearly to Johnny Ramone. The guitar style that people most associate with punk—briskly downpicked barre chords executed with blinding precision at breakneck tempos and marshaled in service of concise catchy song structures—is the invention, progeny and proud legacy of the man born John Cummings on Long Island, New York.
{"product":{"id":"113469598","stock":"instock","price":"539.99","name":"1960s K300 Solid Body Electric Guitar","download":false,"sku_id":"113469598","checksum":"234720911023","rep_id":"site5113469598","displayId":"113469598","sku_display_id":"113469598","sku_rep_id":"site5113469598","gc_pro":false},"category":"Electric Guitars","pageName":"product_detail","subcategory":"Solid Body Electric Guitars","dept":"Guitars"}
Now we switch gears to a company called Unicord, which was owned by Sid Hack. At some point in the early ’60s (probably in around ’64), Unicord purchased the Amplifier Corporation of America (ACA) which was located in Westbury, New York, a northern suburb of New York City. ACA made Haynes guitar amplifiers and an early distortion device powered by batteries.

Like Television not too long before them, Fugazi founders Ian MacKaye and Guy Picciotto engaged in a locomotive, dub-influenced dual-guitar shouting match. Though most of the talk around Fugazi inevitably leads back to their founding ethos, that way of thinking and operating permeated the music as well: Together, MacKaye and Picciotto were anti-frontmen, playing like a living, fire-breathing, two-pronged embodiment of democracy.
Most Heroic Moment: The simple, searing lines of 1990’s “Turnover.” D.B.
SWEET just in a famous Vintage Classic BOOMER Folks from Nippon Gakki RED LABEL 000 OM type Yamaha FG We have just done our JVGuitars set her up with our Martin Bone Nut & Compensated Saddle se as well as upgraded bridge Pins to solid Ebony with Abalone dot with brass ring and of course a new set of Martin Strings 80/20 Bronze 12's.. and this guitar Sounds like a true vintage classic This guitar is AWESOME and is in BEAUTIFUL Condition! Classic Martin 000 OM style copy from Yamaha this guitar rings like a bell with excellent intonation. No Cracks no problemo like so many of these I see and just pass unlike the majority this guitar has excellent play action and is super fun to play! If your looking for a well aged ( almost 50 years ) just try to buy a 50 year old Martin $$$$$$$$$$$ WoW... This guitar is a Boomer surprisingly so but I have carried these FG110 Nippon Gakki's for decades now myself and was always impressed by the good one's... This one will impress you too.... at this price point its hard to beat this old Nippon Gakki Red Label 000. True Japanese Vintage guitar it top vintage condition as seen... Ready to purchase contact Joe at: jvguitars@gmail.com Thank you for your interest in our quality Vintage Guitars, Joe Pics soon to come no worries its excellent!!!.
It's the neat switching that makes this very classic-looking Tele act a little differently. All the standard Tele pickup selections - bridge, bridge and middle (in parallel) and neck - are in place, but it's a four-way switch, as opposed to the standard three-way; the additional selection provides us with both pickups in series for a bigger, louder and more humbucker-like 'secret' sound. The volume control has the S1 push switch in the top of the control knob: pushed down, the parallel and series-combined pickup selections are out-of- phase, giving three additional sounds over the standard Tele. The Baja sticks relatively close, of course, to the classic 60s Tele recipe. The rosewood 'board and alder body just seem to give that lovely smoothness to the high end that will make it less ear-wearing, especially if you're swapping over from an older-style humbucking Gibson. The standard mix is typically classic, wider than a Strat's but still nicely textured; the neck pickup here sounds a little fuller than some older readers or vintage Fender electric guitar owners will remember.
Overall length is 28 1/2 in. (72.4 cm.), 10 in. (25.4 cm.) width, and 1 5/8 in. (4.1 cm.) in depth, measured at side of rim. Scale length is 15 1/4 in. (387 mm.). Width of nut is 1 3/4 in. (44 mm.). All original and complete, and quite clean overall; there are a few small dings to the finish and some light checking-almost inevitable on the Eko-made Vox instruments. The only notable finish marring is one spot where a superglue repair to a cracked pickguard corner left a bit of residue behind. A very nice little player, with an awful lot of chime! Excellent - Condition.
While most think of the history of American guitars in terms of American manufacturers, if you’ve followed this column you know the tradition is much richer. Among the major players in the American market were the many importers and distributors who enriched the guitar landscape with instruments – usually at the lower ends of the market brought in from other countries, primarily from Europe, Asia, and to a lesser extent, Latin America. The analogy with automobiles is obvious. While we tend to think of the automobile industry in ethnocentric terms, it’s impossible to think of “cars in America” without considering Volks-wagen Beetles, Toyota Corollas or Datsun Zs (Yugos and Renaults deliberately ignored).
I started playing & kinda grew up then (although my wife would dispute the 'grew up' part). We used to play mostly 9s or 10s. It depended on the quality of the neck on the guitar we could afford. A good guitar neck/fret job would let you go to the lighter 9s. You couldn't get all the great pedals then, so sustain was often achieved with some feedback, which is a product of TURNING UP the volume. Lighter strings seemed to feedback more easily. Lighter strings don't last as long as heavier ones, so unless you love re-stringing, 10s are a good compromise. I think Billy Gibbons still plays 8s, but he has a guitar tech that probably changes them for every show.
Harmonizers – Commonly used for vocal harmonies, these pedals can do a lot to beef up your sound. You can also use them in creative ways, like Steve Vai and Robert Fripp, who have been known to disable the main signal altogether so that their music is coming only from the pitch-shifted output. Using a modern harmonizer can be as easy as setting it to the key you’re playing in, and many even support more than one harmony at once.

4.  Cracked end block because customer used a drill bit meant for steel to enlarge hole for the jack used on an acoustic.  Fix:  This can be tricky.  First you have to assess the damage and that can be challenging.  Some of these miniature cameras work great.  I’ve had success using a point and shoot on a timer to take a snap.  If the crack is small you might be able to use cyano to repair it.  If the end block is cracked all the way through, the back may need to come off and the block replaced… Again, not something you’re going to do on a cheap guitar.   The proper way is to use a step reamer to get the correct sized hole.


I have an old Montclair that my uncle modified. He told me that is a '52 but the info here dates it as '60-62 if I remember correctly. I just registered over at the forum, I thought you guys might get a kick out of seeing this guitar. My uncle stripped almost all the paint, there's a bit under the bottom of the neck just to show how it was. He added a hand carved bridge and custom binding on the backside. Also there are a few other unique mods. I really am interested to see what you think about this guitar. It is my main player and has been for years now, an amazing sounding punchy guitar. Hopefully I'll be able to post up some pics at the forum. Cheers! -Gabriel-
{ "thumbImageID": "Les-Paul-Special-I-P90-Electric-Guitar-Worn-Cherry/H77433000003000", "defaultDisplayName": "Epiphone Les Paul Special I P90 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Worn Cherry", "sku": "sku:site51314371183322", "price": "119.99", "regularPrice": "149.00", "msrpPrice": "252.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Les-Paul-Special-I-P90-Electric-Guitar-Worn-Cherry-1314371183322.gc", "skuImageId": "Les-Paul-Special-I-P90-Electric-Guitar-Worn-Cherry/H77433000003000", "brandName": "Epiphone", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-I-P90-Electric-Guitar-Worn-Cherry/H77433000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Worn Black", "sku": "sku:site51314371183302", "price": "119.99", "regularPrice": "149.00", "msrpPrice": "252.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Les-Paul-Special-I-P90-Electric-Guitar-Worn-Black-1314371183302.gc", "skuImageId": "Les-Paul-Special-I-P90-Electric-Guitar-Worn-Black/H77433000001000", "brandName": "Epiphone", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-I-P90-Electric-Guitar-Worn-Black/H77433000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Worn TV Yellow", "sku": "sku:site51314371183312", "price": "149.00", "regularPrice": "149.00", "msrpPrice": "209.00", "priceVisibility": "1", "skuUrl": "/Epiphone/Les-Paul-Special-I-P90-Electric-Guitar-Worn-TV-Yellow-1314371183312.gc", "skuImageId": "Les-Paul-Special-I-P90-Electric-Guitar-Worn-TV-Yellow/H77433000002000", "brandName": "Epiphone", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Les-Paul-Special-I-P90-Electric-Guitar-Worn-TV-Yellow/H77433000002000-00-60x60.jpg", "imgAlt": "" } ] }
*VERY GOOD CONDITION, W/CD (NEVER USED)* PAYMENT is requested within 2 days or 48 hours of purchase.   FEEDBACK: Positive feedback and a 5 star rating is such an important part of the eBay rating system. Please contact me before leaving Neutral or negative feedback, I will try to help you. I will leave feedback when feedback is left for me!   SHOP WITH CONFIDENCE 😎   TRUSTED & ESTABLISHED SELLER!!
  Technology is not based on good materials and dexterity alone. It's how you finish your work that counts. It's the little details that you labour over until it's just right. It's an arduous process of creating and destroying and rebuilding until its perfect; until there's nothing left to add, and nothing left to take away. Then it's ready. Swing is well known for its attention to detail in our incredible Custom Shop models, but what you may not know, is that we make no distinction between them and our retail guitars. They all receive the same exacting standard we demand of any product that carries the name "Swing". Our attention to quality and detail costs us more than what other manufacturers consider as an adequate alternative. We do not take shortcuts with every detail because we have found that the careful, educated player can hear those shortcuts. Again, it shouldn't come as surprise though, it's really the only explanation why after only 2 years in business we rose to become #1, and have stayed there for three years and counting.
{ "thumbImageID": "PM-TE-Standard-Travel-Acoustic-Electric-Guitar-Natural/K36613000001000", "defaultDisplayName": "Fender PM-TE Standard Travel Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Natural", "sku": "sku:site51500000138832", "price": "699.99", "regularPrice": "699.99", "msrpPrice": "700.01", "priceVisibility": "1", "skuUrl": "/Fender/PM-TE-Standard-Travel-Acoustic-Electric-Guitar-Natural-1500000138832.gc", "skuImageId": "PM-TE-Standard-Travel-Acoustic-Electric-Guitar-Natural/K36613000001000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/PM-TE-Standard-Travel-Acoustic-Electric-Guitar-Natural/K36613000001000-00-60x60.jpg", "imgAlt": "" } ] }
The guitars included three bolt-neck Strat-style models, the GS-1 (one humbucker), GS-2 (two humbuckers) and GS-3 (humbucker/single/single). Most had locking Kahler vibratos, although at least one GS-3 has been seen with a traditional fulcrum vibrato. The bodies had a German carve relief beginning at the waist and extending forward to the cutaway horns. The necks had 21-fret rosewood or maple fingerboards with dots. The six-in-line heads were kind of squarish and bi-level, with a carved relief along the lower edge, kind of an Ovation trademark. The logos said Ovation Ultra GS. The GS-1 (volume only) and GS-2 (volume, tone, three-way) had pickups mounted on rings on the top. The GS-3 featured a black Strat-style pickguard. One source refers to a GSL model, but nothing is known about what this means, if it isn’t a typo. Most of these came with typical exposed-pole DiMarzios, but the previously mentioned guitar with the fulcrum vibrato also had twin-blade pickups with DiMarzio stenciled on the covers.
Maybe the pickups that came with your guitar are just cheap and not up to your standards. At that point, an upgrade might be less of a stylistic issue and would done for the purpose of improving the overall sound quality of your instrument. In most cases, upgrading the pickups on your guitar are the single most effective way to improve the overall tone and sound quality.
In 1960, Gibson experienced a decline in electric guitar sales due to their high prices and strong competition from Fender’s comparable but much lighter double-cutaway design, the Stratocaster. In response, Gibson modified the Les Paul line. This 1961 issue Les Paul guitar was thinner and much lighter than the earlier models, with two sharply pointed cutaways and a vibrato system. However, the redesign was done without Les Paul’s knowledge. Although pleased with the sound, he asked Gibson to remove his name from the instrument until they fixed a design issue with the neck.[18] This separation occurred in 1960, but Gibson had a surplus stock of “Les Paul” logos and truss rod covers, and so continued to use the Les Paul name until 1963. At that point, the SG guitar’s name was finally changed to “SG“, which stood simply for Solid Guitar. In addition to the SG line, Gibson continued to issue the less expensive Jrs and Specials (and the Melody Makers) with the newer body style. These, together with the Firebird, were the standard Gibson solid-body models until the reintroduction of the Les Paul Standard Goldtop and the Les Paul Custom guitars to the market in 1968.
This is just what a guy or gal needs to help him or her make an informed decision on making a electric guitar purchase. All the topics and explanations of the given topic, pick-ups, machine heads etc… were easy to follow and understand. Not a lot of tech talk that would either confuse or intimidate a perspective buyer, that is a feat in its self kudos to your writers. keep up the good work.
Launch price: $2,799 / £2,399 | Body: Laminated maple | Neck: Maple | Scale: 24.6" | Fingerboard: Ebony | Frets: 22 | Pickups: 2x Full'Tron humbuckers | Controls: Bridge volume, neck volume, master volume, tone, 3-way selector switch | Hardware: Anchored Adjusto-Matic bridge, Gotoh locking tuners, Graph Tech TUSQ XL nut | Left-handed: | Finish: Cadillac Green
POWER – amps are created for amplifying the sound (duh) in the first place. Of course, nowadays amps are these versatile things that can do pretty much anything but cook you a scrambled egg (maybe SOON?). But power is expensive. This might sound like some deep statement I make as I look into the sunset but what I mean is wattage is not a cheap thing to come by. That is why most inexpensive models or practice models (which are often the same) do not have a lot of wattages. While this might be disheartening, trust me, as a beginner you won’t need a lot of watts. I mean unless you are a prodigy you will be spending a lot of time practicing on your own whether it be in your room, basement or wherever. You won’t be needing the wattage that much unless you are playing with other instruments or on stage. AND if you are going on stage, then you should be great enough not to need a practice amp, in the first place.
Wampler would be considered a boutique pedal manufacturer, which means they'll tend to be a little more expensive, but also more likely to give their products more creative attention and include features like true bypass, which you don't get with Boss pedals. It's also a unique blend of delay layers and reverb tones, which can really draw you in and make you want to deviate from the cheaper reverb pedals.

Input kewords into the searchbox at the top of each page, then click the WHAT'S IT WORTH button. The search engine will find matching pages based on keywords you type into the Search Box. The engine searches all categories of objects, not just this particular category, so you may get some irrelevant items in your search results. Too many results? Be more specific. Not enough results? Be less specific.
It wasn't long before Southland went to hell in a hand basket. I would like to acknowledge the professionalism of people like the late Lee Ingber who was quality minded enough to know that junk will ruin any business. It's too bad that the last owners of Southland never learned that, even as their company faded into the sunset of the graveyard of greed.
Fretwire can vary from some makers as it is shaped by extrusion thru a series of roller dies and the dies wear.  I have observed actual Dunlop 6105 in my shop varying from .088” to .090” wide and from .052” to .055” tall.  Due to the inconsistent size and tang formation, I generally do not use Dunlop fretwire these days, instead preferring the more accurate German made Jescar or the Japanese made Stewart McDonald fretwires.  Both Jescar and SM have very well formed tangs and barbs and are very consistent. I will refer to the Dunlop numbers below but only for very general description – always verify actual sizes!
The SimulAnalog Guitar Suite is an old but still popular free guitar effects program. It contains a set of VST plugins that emulate some of the most common used guitar effects and amps. It has simulations of five essential guitar effects which include Boss DS-1, Boss SD-1, Tube Screamer, Oberheim PS-1 and Univox Univibe. The SimulAnalog Guitar Suite was born out of an academic research and thus applies a zero deception, no marketing hype approach. The interface is very basic but the sound is said to obtain lass than -40dB of difference compared to the original hardware.
8dio sampled a 200-year-old Italian made mandolin to create a gorgeous sounding VST that simply rules, and will fool even the most well-trained ears into thinking it’s the real deal.  Like with the others in the series, we have our usual clean legato, artifacts, effects, tremolos, mutes — basically, you have everything you need to get the job done 99% of the time.

This Hellraiser C1 guitar features a mahogany body and a quilted maple top and abalone gothic cross inlays. It looks and feels fantastic! A couple of things that make it sound even better are the locking tuners, that keep it in tune, and the EMG noise-cancelling scheme that makes sure that the only sound the guitar makes is the music you’re playing.


{ "thumbImageID": "Pro-Mod-So-Cal-Style-1-HH-with-Floyd-Rose-Left-Handed-Electric-Guitar-Black/J48559000001000", "defaultDisplayName": "Charvel Pro-Mod So-Cal Style 1 HH with Floyd Rose Left-Handed Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black", "sku": "sku:site51500000035005", "price": "929.99", "regularPrice": "929.99", "msrpPrice": "1,282.74", "priceVisibility": "1", "skuUrl": "/Charvel/Pro-Mod-So-Cal-Style-1-HH-with-Floyd-Rose-Left-Handed-Electric-Guitar-Black-1500000035005.gc", "skuImageId": "Pro-Mod-So-Cal-Style-1-HH-with-Floyd-Rose-Left-Handed-Electric-Guitar-Black/J48559000001000", "brandName": "Charvel", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Pro-Mod-So-Cal-Style-1-HH-with-Floyd-Rose-Left-Handed-Electric-Guitar-Black/J48559000001000-00-60x60.jpg", "imgAlt": "" } ] }

One of the greatest things about being a touring musician is having the opportunity to see, hear and play with some of the greatest guitarists on the planet. Over the course of my career, I’ve performed with legendary guitarists like Ted Nugent, Steve Cropper, and Glen Campbell, to drop just a few names. Playing lead for a headline act like Toby Keith also allows me to watch fantastic guitarists like Keith Urban and Brad Paisley take the stage before me.
Adding effects at the mixing stage gives the engineer greater creative flexibility, but if the guitarist needs to hear the effects to play, then you may get a better artistic performance by recording them with the take. All I'd say on this point is that editing is much more difficult if the sound is recorded with delay or reverb, so an alternative is not to record these effects initially, but still add them to the monitor mix for the player's benefit during performance. Effects like chorus and wah-wah can be recorded straight off, if required, as they don't affect the ease with which a part can be edited. Ultimately, the performance is what really counts, so compromise in favour of the player's artistic needs rather than your technical needs where a choice has to be made.
We selected this guitar as our Top Pick because it’s an instrument that could suit anybody. It has everything you need from your electric guitar and it’s easy to play. A good classic that will stay with you for many years to come. It suits both beginners and guitarists who have been playing for a while. True, a professional guitarist would buy something pricier, but if you’re not super picky this guitar will do perfectly well!

This acoustic-electric parlor style guitar features a solid cedar top and solid sapele back and sides, premium appointments that other builders will require you to pay top dollars for. And it features old school parlor style body shape, which gives the instrument a vintage appeal, and blues box style tone with emphasis on the middle frequencies. This makes it ideal for blues, folk and old school comping, a good contrast to regular sized acoustics in a mix.

Our congratulations and deepest thanks on making Ibanez your choice of instrument. Ibanez standards are second to none. All Ibanez instruments are set up to our strict quality control standards before shipping. The purpose of this manual is to explain how to maintain your instrument’s finish and to keep your guitar playing as well as it did when it...

We are your Vintage Pickup specialists.   We have cornered the market of manufacturing the most accurate vintage pickup reproductions to which can not be equaled.  Our process is to chemically analyze an original pickup magnets and wire, then we reproduce them with the exact same magnets and wire.  We don't use stock magnets or wire.   We don't degauss magnets and say they are vintage.  Our magnets are only as strong as the elemental composition will hold.  Our wire is specially manufactured for us, we have many batches of wire with all different types of resistances and O.D.'s.  Our wire also is processed differently than modern conventional wire, these little details are what makes the Klein Pickups Reproductions the most accurate in the world.   We have a full array of models that we reproduce.  Check out our site for the full list of all of our offerings.   As a small business we always appreciate your business & support.  -Thanks

Thank you for supporting Ibanez Collectors Forum. Please help your favorite Ibanez guitar site as we endeavor to bring you the latest information about Ibanez custom vintage electric and acoustic guitars. Here you can discuss ibanez, guitars, ibanez guitars, basses, acoustics, acoustic, mandolins, electric guitar, electric bass, amplifiers, effect pedals, tuners, picks, pickups.


Nylon strings are the standard for classical guitarists in today’s market.  While there are many types of nylon strings, the most commonly seen is clear nylon.  They are visually appealing while providing a clarity of tone with a bright attack that offsets the mellow overall tone of the classical guitar.  Other options include black nylon, rectified nylon, and composite strings.  The best classical guitars on the market come strung with nylons by default still.
A six-string guitar has five musical-intervals between its consecutive strings. In standard tuning, the intervals are four perfect-fourths and one major-third, the comparatively irregular interval for the (G,B) pair. Consequently, standard tuning requires four chord-shapes for the major chords. There are separate chord-forms for chords having their root note on the third, fourth, fifth, and sixth strings.[41] Of course, a beginner learns guitar by learning notes and chords,[42] and irregularities make learning the guitar difficult[43]—even more difficult than learning the formation of plural nouns in German, according to Gary Marcus.[44] Nonetheless, most beginners use standard tuning.[45]
The tone controls compensate for and complement the somewhat lifeless and mostly midrange-y character of the average guitar pickup. The gain control, often designed with a pull-boost, basically excites and heats the preamp tubes, which along with judicious use of both the amp and the guitar’s tone controls will begin to produce much of the sonic seasoning and flavor that guitarists and their fans crave as it flows from the speakers.

Everyone from Jazz guitarists to lovers of Queens of the Stone Age style heavy rock have fallen in love with the Artcore series since it was first introduced in 2002. Fusing expert workmanship with affordability, the Ibanez 2017 Artcore AS53 Semi-Acoustic Guitar, Transparent Black Flat is one of the best cheap electric guitars you’ll find on the market today. It’s budget friendly price tag makes it a fantastic choice for beginners whilst the high-quality pickups and superb tonewoods are the reason why so many pro level players will choose it for the stage and studio.
Of course, as guitar players we still want to remain open to a number of tonal aspects that happen after the front end of the initial attack. These elements aren’t necessarily in the front part of the very beginning of a guitar tone, nor are they delegated to the trail of lingering sustain. “The reason why people sound a certain way is because of little nuances, those little pull offs, those hammer ons, those plucking [dynamics]— the sequence of those things. Think of it as a sonic palette. That sequence is what makes the artist sound like himself.”
Early valve amplifiers used unregulated power supplies. This was due to the high cost associated with high-quality high-voltage power supplies. The typical anode (plate) supply was simply a rectifier, an inductor and a capacitor. When the valve amplifier was operated at high volume, the power supply voltage would dip, reducing power output and causing signal attenuation and compression. This dipping effect is known as "sag", and is sought-after by some electric guitarists.[46] Sag only occurs in class-AB amplifiers. This is because, technically, sag results from more current being drawn from the power supply, causing a greater voltage drop over the rectifier valve. In a class-A amplifier, current draw is constant, so sag does not occur.
Artists have been converging on this sound for more than a decade before Davies used it. In 1951, “Rocket 88” by Ike Turner and the Kings of Rhythm took advantage of a distorted amplifier that had been damaged in transport. The same thing happened to the Johnny Burnette Trio in 1956, when Paul Burlison pulled out a vacuum tube from his amplifier after it fell off the top of the band’s car. He loved the sound so much he used it to record “The Train Kept a-rollin,” which inspired a whole raft of British musicians:
Depending on your choice of guitar kit you may be required to perform a small amount (or a large amount) of work wiring the guitar. This typically involves a soldering iron and a basic understanding of guitar electronics. You will also need to be able to follow schematic diagrams of pickup configurations. It’s not a one size fits all job either, wiring up a Telecaster is different to wiring a Stratocaster and a Les Paul or hollow body is different again.
This setup is the same as the first one above, however, the volume pedal has been placed near the end of the chain right before the delay and reverb effects.  This allows you to have full control of the volume of your signal right before the delay and reverb effects. This is useful for fading in a fully overdriven signal without cleaning up the signal at the lower range of the sweep.

You might be playing guitar in a cramped garage or a poky bedroom – but it’ll sound like you’re gigging a cathedral when you step on a quality reverb pedal. Reverb brings a sense of space, depth and drama to even the most basic guitar parts, and as this video shows, few effects deliver more atmosphere for less effort. Using the BOSS RV-5 as our demo model, we’ll show you just how flexible reverb can be, running through key controls that adjust brightness, volume and more. Then, we’ll show how your playing can benefit from three different reverb types, whether that’s the vintage sound of spring reverb, the rock-club chug of room reverb, or the stadium-sized shimmer of hall reverb.
SolidBody (2008) – Taylor’s take on a traditional solid electric guitar. Made from a solid slab of wood with cavities only for the pickguard or direct mounted pickups, and the bridge. Designed from the ground up, each SolidBody model features solderless pickups or a solderless pickguard which permit for musicians to effortlessly change the sound of their guitar. The SolidBody line is fully customizable with a wide combination of wood, colors and electronic configurations, and single or double cutaway options which enables anyone purchasing a SolidBody to get the sound and look that they want. All options are available for customization through Taylor’s SolidBody Configurator on the Taylor website.
POLISHING Once you have completed the wet sanding you wil have a pretty smooth surface that is almost a dull shine. You can either hand polish the finish or use a polising attachment to buff it out. Stew Mac has a polishing pad that attaches to you drill. Or you can get 6" foam bonnets from an auto parts store that will fit over the sanding disk attachment you may already have. It is best not to use any thing made from cotton because it will cut through the finish. Stew Mac also has polishing compounds that you will use in order working you way down to the swirl remover. It's on the expensive side so I use McGuires polish that you can get from the auto shop. If you use a buffing attachment make sure that you uae a different attachment for each grade of polish. Don't use the same pad for each one. Also remember to wait 10 minutes after buffing before you wipe off the surface. The lacquer gets hot and soft after buffing so give it time to cool. You will have to hand polish the cutaways, don't attempt to use the buffer on the edges of the guitar or cutaways because you will burn though the finish.
This electric guitar style has experienced surges and lulls in its popularity, but has never fallen off the scene, due to the number of great players who have chosen to use the Flying V, such as Jimi Hendrix, Dave Mustaine, Kirk Hammett and Michael Schenker.  The Flying V offered many of the same benefits as the SG with a much more distinctive body shape.  It is now a very common guitar among heavy rock and metal guitarists and will achieve its destiny of being a guitar of the future!

While often overlooked, the speakers are an amp’s most crucial component—they’re the last thing standing between all that electronic gobbledygook and the sound that reaches your ears (except for yo’ mama’s fist, but that’s another story). Different sized speakers have different tonal characteristics, and you should consider speaker sizes the same way you’d consider an amp’s wattage rating. Speakers are like booty—small ones are tighter and big ones have more bottom end. But like a pair of pants, cabinet design can shape bottom end as well. Which is why a closed-back 4x10 cabinet may put out more bass than a 15-inch speaker in an open-back cabinet.

“Photocell Tremolo is found in mid-1960s American amplifiers. Those classic circuits used a light-dependent resistor to attenuate the input signal, coupled with a miniature neon bulb that is connected to the LFO. As the LFO oscillates, the bulb gets brighter and dimmer which in turn varies the resistance of the LDR. The varying resistance works with other circuit impedances to change the signal level, which produces a characteristically ‘hard’ sounding tremolo that moves between two levels, reminiscent of a square wave.” Got that? Well it is tricky and they do sound somewhat different but essentially they produce the same effect. The pedal I am using here, the Fulltone Supa-Trem uses a photocell to produce the sounds found in the classic Fender amps and most common tremolo circuit.


Taylor has swiftly made several electric guitars that made their way to the hands of professional guitarists onstage. Moreover, a few of their models are directed towards working players too. In fact, Taylor seems to be caring about the beginners and intermediate level players as well, since they produce several guitar models aimed at these customer groups. If you are ready to scour out your wallet to get your desired guitar, Taylor will be the perfect choice for you.
3) The pedal switch. Placed on the top of the pedal, pressing it with your foot turns the effect on and off. This is where the name “stomp boxes” comes from – you “stomp” the box to turn on the effect. Pedals are most commonly placed on the floor next to each other so they can be toggled with your feet while you play with your hands, but larger units are often placed in large racks on top of one another, as otherwise they would take up too much floor space.
After shaping your sound, is important to add some depth to it, and here’s where the ‘ambiance’ pedals find their way into your rig. The chorus effect should be used properly, without overdoing it, but can give great results: the depth and the ‘3 guitarists playing your part’ effect can work amazingly well for your music. Delay and Reverb can be used lightly, in order to enhance your sound and fill up your guitar solos with a little space (by setting up a nice spring or hall reverb settings and a dotted delay) or heavily, to achieve creative sounds where the sky is the only limit.
Although I’ve spent most of my life focusing on audio journalism, I’ve been active as a musician since taking up guitar seriously in the 1970s, and I have played lots of gigs with jazz, rock, and folk groups in New York and Los Angeles. I now play mostly double bass and ukulele; I currently play in three jazz groups in Los Angeles, and I sub regularly in a couple more groups. I also conduct more-or-less weekly jazz jam sessions at my home, where I accompany numerous guitarists of widely varying skill levels, toting all sorts of axes. Having conducted innumerable multi-listener comparisons of audio products over some 25 years, I have a good idea of how to make product tests fair.
The earliest documented performance with an electric guitar was in 1932, by guitarist and bandleader Gage Brewer. The Kansas-based musician had obtained two instruments from George Beauchamp of Los Angeles, California, and he publicized his new instruments in an article in the Wichita Beacon, October 2, 1932 and through a performance later that month.
With that in mind, we need to point out something about this piece of content, and others like it that we have written: These recommendations are based on the knowledge and opinion of real musicians. We are not marketers or internet gurus trying to make a buck off Amazon. Now, we do use affiliate programs to support this site and those who run it, but we are not simply throwing pedals up without knowing why we're suggesting them. The point is to provide a proper context for your purchase, which we believe is the best way to make a sale, anyway.
This guitar is perfect no matter if you’re a beginner or have been playing for many years. The design is vintage at its best, with a lovely soft V-shaped neck and great colors, namely Surf Green, Daphne Blue and Fiesta Red. This guitar has a very traditional look that most people like. True, some people would feel that it’s a little bit too mainstream, but others would reason that hey, if it’s good enough for everybody else, it’s good enough for me!

Replacing or repairing knobs. Knobs are covers for your pots so you can easily turn them, if any of your knobs are unable to be correctly placed on try due to broken or enlarge holes, place a good amount of tape around the pot's shaft that covers it and try to keep the the knob on the tape. If you cannot do so then you may need to replace your knobs.
The first impressive thing about the Zoom G3X is its build quality. This unit is solid, which puts our fears to rest that Zoom may have sacrificed build quality since the G3X is more on the budget side of the price spectrum. In the reviews and recommendations we read, several owners make it a point to comment that it feels like a serious piece of equipment that could withstand some abuse because of its sturdy metal construction. The G3X can be powered with a 9V adapter (which is conveniently included), or four AA batteries. Zoom claims about 6 hours of battery life, but in our experience manufacturers tend to exaggerate battery life a bit. Still, battery power is very convenient if you’re traveling with the G3X and want to do some on-the-go playing, or just taking it from room to room in your house (to save some money in the long run we recommend rechargeable batteries).
ZPS (ZERO POINT SYSTEM) OF ZR TREMOLO Main Spring Stopper Tremolo Block Stop Rod With the guitar tuned correctly, adjust the Main Spring make sure that the Stop Rod makes contact with the Tremolo Block and Stopper. If the Stop Rod does not make contact with the Tremolo Block and Stopper, adjust the Main Spring adjustment screw until contact is made.
Artists have been converging on this sound for more than a decade before Davies used it. In 1951, “Rocket 88” by Ike Turner and the Kings of Rhythm took advantage of a distorted amplifier that had been damaged in transport. The same thing happened to the Johnny Burnette Trio in 1956, when Paul Burlison pulled out a vacuum tube from his amplifier after it fell off the top of the band’s car. He loved the sound so much he used it to record “The Train Kept a-rollin,” which inspired a whole raft of British musicians:
PICK GUARD - KRAMER 450 - LO GIBSON - GOLDTOP - GIBSON SG CUSTOM SHOP - THUNDER JET - TAKAMINE - GIBSON 1959 - 450 12 - 66 ES-330 - 1972 - HAGSTROM F-300 RED LEFTHANDED - GIANNINI - BALLADEER - WHITE LES PAUL - HAGSTROM BRIDGE - CONRAD - LES PAUL 1953 - PROJECT - WASHBURN EA27 - KALAMAZOO KG - FRAMUS BASS - BASS VI - 1967 - ES-330 - HOLLOW - 1981 LES - BALDWIN BABY BISON - STELLA ACUOSTIC - MARTIN N-20 - VAN EPS - LES PAUL RECORDING - PIG - MARLBORO - HAGSTROM F12-S - FENDER STRATOCASTER 63 - LS 6 - HARMONY - J-45 - UNIVOX BASS

While continuing to keep the E string depressed at the first fret, move up the neck from the 12th fret to the end of the fretboard, continuing to depress the string at each of the successive frets. As you move up the fretboard, watch if and how much the distance between the bottom of the string and the top of the frets in the 6-7th fret range changes, if at all. The less the gap rises, the flatter, overall, the neck is. Using this method you may discern that there is more curve in one area than another, and not necessarily centering on the 6-7th fret area. In some cases this curve will be resolved by changing the tension on the truss rod. In other cases, adjusting the truss rod tension will not resolve them, and fret leveling, refretting, or heat bending the neck(rarely) may be necessary.
The Line 6 Spider IV is the most fully featured beginner amps out there, yet is surprisingly inexpensive, only edging out the Orange Crush PiX CR12L a little bit on cost. The Line 6 Spider IV 15 offers four amp models, six built in effects, a built in tuner, a headphone jack, and a CD/MP3 player input. Everything a beginner needs to practice in one compact package. These features aren’t completely necessary for beginners to have, but they do serve as a nice convenience and the Spider IV does not cost that much more in the process to add them. On top of that, the Spider IV still manages to be straight forward and easy to use, despite all the built in options.
The fretboard (also called the fingerboard) is a piece of wood embedded with metal frets that constitutes the top of the neck. It is flat or slightly curved. The curvature of the fretboard is measured by the fretboard radius, which is the radius of a hypothetical circle of which the fretboard's surface constitutes a segment. The smaller the fretboard radius, the more noticeably curved the fretboard is. Fretboards are most commonly made of ebony, but may also be made of rosewood or of phenolic composite ("micarta").
The GuitarTricks instructors are working professional guitarist and great teachers. With more than 45 instructors you have plenty of choice to find the ones you like best. There is a structured, best practice, teaching approach to every lesson, song and the entire curriculum which beats the hap-hazard approach of picking free lessons on YouTube. I also like that the I can learn not just what something does but WHY it does it and how to apply it to other parts.
So this book is a great way to keep on top of practicing valuable techniques to build a very solid foundation over the course of a year. What this book is not good for is licks or detailed instruction about technique. It is much more focused on giving you a set schedule and practice regime that will build your skills. For people who get distracted and are unsure of what to practice in order to maximize their time and improve their skills, this book is a good way to remain focused and build a valuable skill set while learning guitar.
Rotary – A modelling effect that recreates the sound of a rotary cabinet amplifier. A rotary cabinet amplifier was originally designed for electric organs as a way to emulate the wobbling sound of a pipe organ by rotating a speaker within its cabinet. However, the effect soon became popular with guitarists as a type of modulation effect. The RT-20 rotary pedal has two speeds, fast and slow. You can control the speed of rotation and the rise time, which is the amount of time it takes to switch between the fast and slow speeds.

The DD-5 offers four switchable delay ranges and 11 modes that give access to delays from 1ms all the way up to a walloping 2000ms. Delay time can also be set in real time using the Tap Tempo function and an optional FS-5U footswitch. With the Hold mode you can sample a passage simply by pressing and releasing the pedal. This item has normal signs of use/wear. Has been kept in clean, dry and smoke free environment.
Hey man this is a really great instructable and i am in sort of the same situation that you were in. I have 2 guitars,a Yamaha CG-101 classical, and a Fender Squier Strat. I want to save up for a warlock or Eipiphone les paul or SG or something, but my income is very low and i am going to get a drum set instead. My parents could care less of music, but they are in it for me. Anyways, my strat has three single coils and what I really want to do is replace them all with EMG's.Would that be possible? But those are like $200 a peice. Maybe i should just wait until i get some more money after my drum set. Thanks and shoot me a PM or something.
The No. 140 Supro Capitan was a handsome f-holed archtop, which was Regal-made. It sported an arched spruce top with a maple body. The hardwood neck had an ebonized fingerboard with pearl position dot and jumbo frets. An oval Supro logo plate sat on the faceplate. A single rectangular metal-covered pickup (with holes exposing the poles) sat just to the bridge side of the middle position. This pickup had six separate coils! It had a “crystaline pick guard,” probably tortoise, and adjustable compensated bridge, National-stamped trapeze tailpiece, and one volume and one tone control situated just behind the �guard. It came with a grey Servitex tweed case, and in ’42 cost $71.50.
Finally, according to Longworth, the earliest examples of these instruments had laminated bodies made of maple, rosewood and mahogany. A second series was made with a combination of maple and rosewood. A third series was made with maple and walnut. The #1034 EM-18 shown here appears to be very early yet has maple and rosewood, so it’s not clear if materials are indicators of chronology or simply the vicissitudes of fate (or the woodshop, as the case may be).
I own several guitars ranging from 700 dollars to 2000 dollars so I knew not to get my expectations up when purchasing a 100 dollar. I bought this as a gift for someone to learn on but when it arrived, I could not believe the quality of guitar this is. The tuning keys are high quality, the neck and fret board are high quality. It holds its tune as good as my Ovation and Ibanez acoustics as well as my 2000 dollar PRS guitar. Very easy to press the strings. Surely I thought this would be the difference maker from my more expensive guitars but it's actually easier to play. The pickup is a little more brighter sounding than on more expensive guitars but it's nothing you can't fix with your settings.
When Levon Helm of The Band sang "I pulled into Nazareth, was feelin' about half past dead" in "The Weight," he wasn’t alluding to a weary pilgrim’s desire for salvation. Rather, he was singing about a mythological trip to Nazareth, Pennsylvania, home of C. F. Martin & Co., makers of Martin flat top acoustic guitars. Founded in 1833 by a German immigrant named Christian Friedrich Martin, whose father was also an instrument maker, Martin...Continue Reading
This old Nickelback hit is made up of only four different chords, written in the Key of G. During the verses only use G – C – F to progress, while the chorus of the song will add an Am (A minor) to change things up a little bit. This is a fun song to listen to and play along with, especially since the song is set a slower tempo, especially for a rock song.
Power amp clipping is not the same thing as preamp/preamp tube clipping. Sending a power amp signal that is getting power amp clipping to a speaker can blow the speaker. Sending a preamp/preamp tube clipped signal through a speaker is not harmful. In practice, part of the "breaking up" amp sound, of a "cranked" amplifier, which is widely appreciated by hard rock, metal, punk and blues musicians, is a mix of preamp and power amp clipping. One of the benefits of using a separate components head system, in which a separate preamp and power amp are mounted in a rack, is that the bassist or bass tech can watch for the clipping warning LED on the power amp and lower the power amp volume, if necessary.
Capture ideas and create songs easily with a riff-based workflow, loop recording, automatic track creation (4 tracks), 7 guitar-oriented effects, support for amp models (AmpliTube, PodFarm, StudioDevil and others), 1 InstantDrummer (expandable), and more. Stay in the creative flow with tools that look like gear, and create complete songs without putting down your guitar!
Some bridges allow players to introduce vibrato into their performance by means of moving a vibrato arm (aka a whammy bar) that moves the bridge up or down. Bridges with this function are often called tremolos. (Note that this is musically incorrect since tremolo means a repeating variation in volume, not pitch, but has been used so long it is accepted terminology.) A tremolo system allows the player to rock the bridge back and forth to adjust the pitch of the notes being played. This is called a floating bridge, and is popular on many guitars. For beginners, it may be better to avoid a locking tuning system for their first guitar. They can be tricky to adjust properly, and can make even a simple string change frustrating for the inexperienced. However, if your budding Steve Vai has his heart set, don’t let that stand in the way.
{ "thumbImageID": "Pursuit-Exotic-Concert-CE-Myrtlewood-Acoustic-Electric-Guitar-Bourbon-Sunset-Burst/K35888000001000", "defaultDisplayName": "Breedlove Pursuit Exotic Concert CE Myrtlewood Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Bourbon Sunset Burst", "sku": "sku:site51500000124748", "price": "599.99", "regularPrice": "699.99", "msrpPrice": "865.00", "priceVisibility": "1", "skuUrl": "/Breedlove/Pursuit-Exotic-Concert-CE-Myrtlewood-Acoustic-Electric-Guitar-Bourbon-Sunset-Burst-1500000124748.gc", "skuImageId": "Pursuit-Exotic-Concert-CE-Myrtlewood-Acoustic-Electric-Guitar-Bourbon-Sunset-Burst/K35888000001000", "brandName": "Breedlove", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Pursuit-Exotic-Concert-CE-Myrtlewood-Acoustic-Electric-Guitar-Bourbon-Sunset-Burst/K35888000001000-00-60x60.jpg", "imgAlt": "" } ] }
Clearly if you need a Gibson but have to count your pennies Epiphone should be your top choice. However, Some people don’t realize that Epiphone was once a competitor with Gibson, and even today some of their semi-hollow and hollow-body guitars are worth mentioning with the top brands out there. The Dot is well known as an affordable version of the Gibson ES-335, but there are also guitars like the Casino, Wildkat, Sheraton and Broadway.

Although this multi-effects pedal is powerful and full of features, it doesn't mean that you’ll have to face those awkward manual reading moments. The ME-70 is like a simple stomp box, each effect section has knob-based controls which makes it easy to dial tones. Similarly, whenever you need to add any effect; just kick press on one of the four foot-switches to fire up the game.


There are many excellent pedals out there, I especially like the ones that contain multiple reverbs like, plate, spring, hall, church, etc. Reverb can be a great subtle effect adding a slight bit of ambience to your guitar sound. This is especially nice when playing in small or dry rooms. Usually the larger the room, the less reverb you may want as the room produces its own reverb, which is exactly what we are trying to create with the effect! One of my favorite reverb tones is the old surf guitar sounds made famous by Dick Dale and the Ventures.
It also comes in a colour that is unique and leaves most other guitars in the dust - their OPB colour, or Open Pore Black finish. It’s a matte black guitar. Matte (or a satin finish) means that you won’t have the grubby finger marks or oil stains that a glossy finish would have. Plus, if you play for a while and your palms get sweaty, this matte finish won’t be slick and slipper - unlike guitars with a glossy finish.
The Mahogany body and neck with rosewood fretboard makes it a highly resonant and great sounding guitar whilst the dual Alnico Classic pickups with push pull coil tapping provide a world of tonality. A SlimTaper D Shape neck profile makes it comfortable for beginners to learn on, whilst pro players will enjoy the ergonomic design 2 hours into their set or rehearsal! Available in more finishes here.
More often than not a customer chooses bone as a replacement for cheap plastic nuts supplied on new guitars. It's such a good material for instruments because it's really dense – meaning vibrations travel through it faster meaning that more vibration is transferred to the rest of your instrument - essential! It's also great because it contains natural lubricants which are essential for tuning stability.
The body was perfectly flat and the sanding sealer that was on it was great. I however in wanting a finish that was like a mirror used a enamel filler primer. The body was then shot with 6 coats of enamel black, wet sanded, and hung up to cure for 2 weeks. After curing the body was then shot over a matter of another couple of weeks with 10 coats of clear (remember that temperature and humidity have an effect ... full review

OLD Morris looks to be equal in all respects to our Yairi CY116, exotic wood construction with very nice old woods and excellent workmanship - fit & f instance they make the fit & finish is amazingly nice on the Terada factory made Morris. If your not familiar with Terada they are responsible for some of the finest Japanese guitars on the planet for instance Ibanez George Benson GB10's and all that high end line, most of Ibanez's Artists, and several other top of the line Japanese legends and they know how to make exceptional guitars and this Morris Classical is no different it sounds beautiful and has the vibe that is if you love the looks and feel of a well seasoned fully broken in 40 year patina and your OK with the top finger drag wear your going to love this vintage beauty yes it has plenty of vibe bit it sounds deep and rich too. Nice meaty neck plays easily with great action and with absolutely no cracks oh it has minor doinks and scratches here & there but nothing horrible this guitar qualifies for a VERY GOOD JVG rating overall vintage excellent but with the wear as seen the neck is still pretty slick no major abrasions and the fingerboard is nice too. Yes this is a very nice Ole Classical that has another lifetime of wonderful service to its new owner. I think you will be very pleased. Any questions just drop me an email to JVGuitars@gmail.com . Thanks for looking Joe.
when FINALLY picking up he was running down the stairs leaving early, i barely caught him so didn't get a chance to play it before taking it home, or would have had a chance to address this disappointment. there were dead frets all over the high strings. he clearly didn't perform the service that i paid for. a year later that vintage les paul is still in the same unplayable condition and needs a full service by a real luthier.  
So few 1958-1960 Explorers were ever made that sightings of these are rarer still. The most notable, however, is likely the ’58 acquired by Eric Clapton during a U.S. tour in 1974 from Alex Music in NYC. I saw Clapton during the 461 Ocean Blvd. tour of 1974 at the West Palm Beach International Raceway. I recall him playing this guitar – he played it for a few cuts before the weather turned bad(there were tornados in the area that day).
This article was tremendously helpful! My daughter is entering college for music therapy, and she is already an accomplished pianist but needed a more portable instrument to see patients. We have been scouting out guitars for some time and are looking to get a quality instrument without breaking the bank. Thank you so much for this well-researched article.

{ "thumbImageID": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst/J73165000002000", "defaultDisplayName": "Squier Strat Pack SSS Electric Guitar with Fender Frontman 10G Combo Amplifier", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Brown Sunburst", "sku": "sku:site51500000053102", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "349.99", "priceVisibility": "1", "skuUrl": "/Squier/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst-1500000053102.gc", "skuImageId": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst/J73165000002000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Brown-Sunburst/J73165000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51500000053101", "price": "199.99", "regularPrice": "199.99", "msrpPrice": "349.99", "priceVisibility": "1", "skuUrl": "/Squier/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Black-1500000053101.gc", "skuImageId": "Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Black/J73165000001000", "brandName": "Squier", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Strat-Pack-SSS-Electric-Guitar-with-Fender-Frontman-10G-Combo-Amplifier-Black/J73165000001000-00-60x60.jpg", "imgAlt": "" } ] }
Mike Longworth’s book shows at least three guitar amplifiers carrying the Martin name from the early ’60s. Who made them is unknown… most certainly it wasn’t Martin. In 1961 Martin marketed a pair of combos, the Model 110T and Model 112T. Both had top rear-mounted controls and a very groovy geometrical grillcloths in a sort of M.C. Escher pattern. Presumably the 110 featured a 10″ speaker, while the 112 had a 12″. The “T” suggests a tremolo circuit. In 1962 Martin offered a very cool #700 portable amplifier, a unit ensconced in a leather carrying case, presumably battery-powered.
Oh and you play really great sounding exercises in blues, rock and country that encourage you to noodle around and find your own riffs and leads to play over the tracks which is something that I had never really been inspired to do before with any other book. The author doesn't just throw a bunch of tired, boring, public domain yankee doodles and scarborough fairs because he is too cheap to pay royalties or some crappy tunes that a kindergardener could write but actual original pro sounding tunes and riffs. Yes, I HAVE been around my fair share of crappy guitar lesson books, thanks for asking!
Launch price: $1,699 / £1,006 | Body: Laminated mahogany, semi-hollow | Neck: 3-piece mahogany/maple/mahogany | Scale: 24.75" | Fingerboard: Rosewood | Frets: 22 | Pickups: 2x LB-1 humbuckers | Controls: Bridge volume, bridge tone, neck volume, neck tone, 3-way selector | Hardware: Guild Tune-o-matic bridge with rosewood base, Guild vibrato, Grover Sta-Tite open-gear 14:1 tuners | Left-handed: No | Finish: Cherry Red, White, Black
WET SANDING You can wet sand with 600 or 800 grit wet sanding papers that you can get from the hardware or auto body shop before you apply the clear coats. You can get precission paper from Stewart Mac Donald that are suppose to cut better, last longer and yeild a better result, but I have never tried them so that's up to you. When wet sanding there are a few things to keep in mind. First you will need to soak the paper overnight in water. You can add a little Murphy's Oil soap to it. It will act as a lubricant and help it cut better. You could even soak the paper in a solvent if you use a laquer finish but I use water because it cleans up easier and dosen't smell. Next be sure not to overly soak the areas that you have drilled holes in. If the water get in the wood it can cause a lift in the lacquer that could lead to cracks in the finish. This is why some people choose a solvent to sand with because it is more forgiving in that area. Start wet sanding with a 600 to 800 grit paper and gradually work your way up to a 2000 plus grit. If you use water you may experience a condition in you finger tips that comes with a prolonged exposure to it called "raisoning". Just let them dry out for a while and get back to work!

If you have been playing for a year or two and are looking at something to replace your current model, it would be wise to save a little more and go for a mid-range guitar that may cost between $300 and $500. On this kind of guitar you’ll notice a big difference in sound, as well as the feel of the instrument and the overall playability. Use this page as a starting point to find something that may suit you. Until then, you are probably best off sticking with your current guitar.


The simplicity and ergonomic design of the Pacifica PA012 body mirrors that of the PAC112. It is also available in exciting colors to match it perfectly to the player preference. Tonewood for PA012 as specified on the Yamaha catalog can either be in alder, nato or agathis, while the PAC112 is only made in alder wood. Neck for both guitars are made in maple with a satin finish then it is overlaid by a 22 medium frets rosewood fingerboard marked by inlay dots.
These guys are great! I took my Martin in for a refret, and it might have been the cleanest I have ever seen it done. Played better than it did when I got it. So after that show of quality work I took... my old Guild to them. It had developed a little belly bulge and warped top. Mark got that thing sounding and playing like brand new. They are priced honest and fair, and do work in a very timely manner. I am done looking for my guitar shop. I highly recommend these gentlemen. See More
The strings fitted to the guitar also have an influence on tone. Rock musicians often[when?] prefer the lightest gauge of roundwound string, which is easier to bend, while jazz musicians go for heavier, flatwound strings, which have a rich, dark sound. Steel, nickel, and cobalt are common string materials, and each gives a slightly different tone color.
×