National Reso-Phonic Guitars - World renowned for their resonator instruments. Unlike acoustic guitars, where the vibration of the wooden body creates the sound, in a resonator instrument the body acts as a speaker cabinet. When the strings are plucked, the vibration is transmitted through the saddle to the resonator. The resonator, or speaker cone, then amplifies that vibration.
An amp head is an amplifier without the speakers. This is the type of amp that is most often used on stages of all sizes, from small clubs to huge stadiums. The reason is that amp heads tend to offer more power and can be hooked up to several different speaker cabinets. This allows you unrivalled power as well as the freedom to mix and match your favorite heads and speakers. Another plus is that they are much easier to carry around to gigs, especially if the venue has its own cabinet. The disadvantages of heads are that they are generally more expensive than a combo, while you will also have to factor in the cost of a speaker when purchasing one.
OK, our math isn't so great, so we've gone ahead and included an 11th amp in this list of 10. Although it's way too soon to be declared "iconic," PRS Guitars' brand-new Sonzera series of amps have been hot topics in gear land since they were introduced at the 2017 Winter NAMM Show. Let's just call them "instant classics." Featuring a rugged steel chassis, custom transformers and road-ready construction, each Sonzera model delivers serious tone with maximum reliability.

It is also important to consider the maximum number of effects that can run simultaneously, which are usually based on effect group types or "blocks". This means that you usually can only have one modulation, one reverb, one drive etc in a preset. Advanced processors allow for more freedom which include combining same type pedals, series/parallel routing, pre-post amplifier routing and many more. While they allow for more ways to craft your tones, these processors also require more tweaking time and are usually more expensive.
Why is Mesa Boogie so low?! Have Mesa Boogie ever made a bad amp? Look how many guys endorse their gear. Have you ever tried a Dual Rectifier or Mark V? It will tear you to shreds. They are AMAZING amps. Best part, they're all tube. Line 6, why the hell are they fifth. Why are they in the top 15? They are nothing but crap digital rubbish. Play a real amp like a Mesa Boogie, line 6, pft. Mesa Boogie is the best amp brand by far.
These two articles show us how me can manipulate coil winding direction, electrical phase, and magnetic polarity to achieve hum-cancellation between two coils. Having this knowledge allows us to create hum-cancelling combinations of coils over and above than just using humbuckers. A good example is using a RWRP pickup in the middle position of a Strat.

We’ll round this list off with a slightly different proposition, particularly with jazz in mind. The Fender Classic Series ’72 Telecaster Thinline is a semi-hollow guitar in the guise of a traditional solid body. It features the same body shape and size of a standard Telecaster but has its horizon’s broadened thanks to the internal routing of the wood and attractive ‘f’ hole on the guitar’s top. Two humbuckers – again, not traditional on a Tele – provide exceptional warmth and versatility. Combined with its high levels of construction and craftsmanship this a guitar which will last a lifetime.

Soft and soulful is the second name of Fender guitars and basses. They are famous for their fruitful and enchanting tone. It is one of the most recognized brands in the world. Every note that is played on this guitar is pleasant and pure. There are two factors that contribute to such a thrilling tone. Firstly, the majestic shape of the 'strat' in resonating wood and secondly, the perfect configuration of three pick ups. The pick ups are usually singe coiled. However, there are cases where double coiled third pick ups have been used. Fender is a very popular guitar brand, and artists like Eric Clapton who plays extremely soft music, and heavy metal bands such as Iron Maiden have also used the same brand. Models like Stratocaster and Telecaster have etched their names among the greatest guitars ever made. Fender offers myriad of designs, styles, and configurations. If you are a beginner, then go for any Fender model, it's probably the best guitar for novices or amateurs.
Les Paul, the legend, designed this guitar. This guitar has had more widespread popularity than the Strat, IMO. Jimmy Page was a huge fan of the Les Paul and the SG. Gibson made the double neck SG on special request made by Jimmy Page which was featured in the song "Stairway to Heaven" in the concert at Madison Square garden. Jeff Beck and Pete Townshend are among other notable people who use the Gibson Les Paul.
Why We Liked It - Even if this isn’t the cheapest guitar on our list, we think the Schecter Hellraiser is the best bargain! To get this much guitar for so little money is almost incomprehensible and we feel like a million bucks when we play it! It not only looks good, it sounds fantastic, and you can be sure to impress everyone who hears you play with this wonderful instrument!
Jump up ^ Peterson (2002, p. 37): Peterson, Jonathon (Winter 2002). "Tuning in thirds: A new approach to playing leads to a new kind of guitar". American Lutherie: The Quarterly Journal of the Guild of American Luthiers. 8222 South Park Avenue, Tacoma WA 98408: USA.: The Guild of American Luthiers. 72: 36–43. ISSN 1041-7176. Archived from the original on 2011-10-21. Retrieved 9 October 2012.
Jazz rhythm guitar often consists of very textural, odd-meter playing that includes generous use of exotic, difficult-to-fret chords. In 4/4 timing, it is common to play 2.5 beat intervals such as on the 2 and then the half beat or "and" after 4. Jazz guitarists may play chords "ahead" of the beat, by playing the chord a swung eighth note before the actual chord change. Chords are not generally played in a repetitive rhythmic fashion, like a rock rhythm guitarist would play.
Bought a Tubemeister 18 Twelve about three years ago. Love the size, and options of this amp. Primarily use it at home. Replaced a Fender and a Marshall combo amps with this one. Really like the sound, but recently blew a power tube as well as a fuse, and capacitor as a result. Replaced the Chinese power tubes with JJ's, when professionally repaired. All seems well, but wonder about the reliability of this amp in the long run. My tech recommended changing the tubes every year or two, especially if using the power soak feature. Running it really hard by doing so. Also, read that it generates more heat inside the cab (no vents. closed back). Overall still like the amp, but after dropping $200 to repair, after spending $800 on the amp.. having second thoughts of long term reliability. Not using the power soak very much any longer, and keeping a better eye on the TSC (tube safety control)... not sure if it actually did what it is suppose to. To me... less features and simplicity could be ...more

Eddie's Guitars specializes in the finest electric guitars available today. We have spent many years seeking out the best builders, brands and models available from yesterday and today. From classics like Fender Custom Shop and Gibson Custom Shop to boutique builders like Collings, PRS, Tom Anderson, Grosh and John Suhr we have every avenue of the sonic world of guitar covered.

Squier Affinity Stratocaster has all the same features of the Fender Stratocaster guitar at a highly affordable price. It has a maple neck and an alder body which gives it a snappy Strat tone. It also has three single-coil pickups that can be manipulated by a 5-way switch. A vintage style tremolo system makes it a great choice for those who like that system.
If you are buying a guitar for a kid, it might be good to know that there are smaller electric guitars especially for children. If it’s a small child, it might be really difficult to reach on a full-size guitar. The best way of determining what size you need is to try different sizes in a music shop or ask the guitar teacher what he or she recommends. If your kid grows quickly and you can’t be bothered or can’t afford to get a new guitar every year there is always the option of renting a guitar until your kid is big enough to play on a full-size guitar.
The noise out of my chain drives me nuts. I want it when I want it, not when all is shut off. I am running a Clapton Signature Strat with humless pickups into my Blues Deluxe. No effects and it is quiet as the dead of night. Plug in the effects (All Boss BTW) and it just starts humming. I have been playing with it and cant seem to isolate the culprit (s)… Frustrating.
Although originally founded in California in 1979 as a company that made replacement parts for guitars, Schecter now produce many models of their own – both mass-produced and custom shop guitars. Like the others on this list, Schecter provide guitars for some big names and have a range of signature models including the guitars of Dan Donegan, Keith Merrow, and Jeff Loomis.
The basic function of the volume knob is to change the level of your guitar’s volume output in a smooth and even way. But there’s more to it than that. Some players use the volume knob as a means of boosting their signal to make solos pop out. For example, if you keep your volume dialed in at seven or eight and perhaps lean on your amp a little more for output, you’ve got two or three more notches to ride your loudness up via the knob when it’s really time to burn. No need to spend money on a volume pedal, and unlike distortion or overdrive pedals this doesn’t change your sound much.
You have all the control you need over your effects and you can use all three at the same time, too – ideal for those who like to create big walls of sound. The delay features a tap tempo control, whilst the FX loop connectivity allows you to hook up any other effects pedals you might have before the delay, which ensures the tonal qualities of those pedals are intact.

This study proposes a systematic approach for modelling and three-axis CNC milling of solid wood parts used in stringed electric musical instruments, mainly in electric guitars and basses, through CAD/CAM technology. Design and manufacturing philosophy undertakes particular characteristics of tonal woods, so as to produce high-quality resonant musical instrument parts with high accuracy. To do so, it is crucial to identify design features and to apply the appropriate machining strategies and parameter values based on obtained knowledge, as these have a great impact on both the acoustic characteristics of the parts and on the total appearance of the instrument, thus making it more appealing in a competitive market. Customization of musical instruments is well received among professional musicians who wish to stand out during their performance, as well as to own an instrument of uniquely original shape and sonic properties. Keeping custom instruments cost reasonable is a challenge, unless the overall production is systematic and modular. The proposed approach was developed and tested on a custom solid electric guitar, which was then finished and assembled with off-the-shelf components to form a great looking and sounding electric guitar.


Martin ukuleles produced in greatest numbers in the smallest soprano size, but concert and tenor sizes were available circa 1922. Concert and tenor models were available in all the following styles, with the exception of Style 0, which was produced only as a soprano. Custom order ukuleles, while rare, were available upon request, and may have combined features from various styles.

1975 Gibson Les Paul "Goldtop", Deluxe to Standard conversion, Electric Guitar. This is from my personal collection. I have another and mostly play my Strat and Tele for the music I'm doing now, so it's time to thin the herd (be aware that I might change my mind about selling it). Great, original Gold Top finish with nice checking. I was actually trying find one with a lot of "green" wear on the top of the body, but this one still has some good character (I hate shiny guitars). Plenty of wear to the finish on the back (see photos). Other than a pickup change and strap button change, the guitar is as I bought it used. When I purchased it there was a set of THC, PAF'S installed (don't ask, they're gone). Personally, I didn't care for them for a few reasons, so I replaced the front with a new, Gibson 490R, AlNiCo II and a Seymour Duncan, Seth Lover in the bridge.  Pots have been replaced and the selector switch appears to be original. It already had the Deluxe to Standard conversion work done (no the truss rod cover is not the original, as it should say deluxe). I believe the bridge and tailpiece are newer units as they shine too much for the rest of the guitar. The jack plate has been changed from plastic to metal. I installed the Schaller strap lock buttons. The tuning machines have been changed to sealed Grovers. The headstock has been re-fin'd in the back, from an what looks to be repairs around the tuners. In doing so, the serial was made very faint, and only somewhat readable. Appears to be "92?128". Has the 70's volute for added headstock strength. Bound, Rosewood fingerboard. Mahogany neck. Plays and sounds great. Original frets have normal amount of wear with plenty of years left in them. Neck and action is adjusted perfectly (for me anyway) and I did guitar set-ups for 12 years at a Fender / Gibson / Martin / Yamaha / etc dealership at $45-$150 a pop. I have sold guitars for many years and have been to "vintage" shows, so I'm fairly versed in guitar speak. This is not a "minty" show piece. If that's what you're looking for, then buy another guitar. This is a player's guitar. The guitar has not had the headstock broken off however like many used Gibsons. We have completely done a "Pro" set up on the guitar, including cleaning all the electronics, tightening machines, oiling the fingerboard, adjusting the neck and action for great playability (clearance at the 9th fret = .012 when fretted at the first and the body) and cleaning and polishing. STAYS IN TUNE!!! I play it though all three of my amps, a Trace Elliot "Super Tramp", Marshall JCM-800 and a '67 Fender Super Reverb (original). Plays and sounds great for about any type of music, except the currently installed pickups are probably too hot for jazz. We also installed a new set of .010 strings. The cream colored pick guard and chrome bracket is in the case pocket, I just removed it as I don't play with them installed on any of my Pauls. It's in fine shape if you wish to install it. Guitar weighs in at 10.5 lbs, assuming our UPS scale is reasonably correct. Original Gibson, Les Paul case with the purple lining included (the lockable latch is locked "open" and we do not have a key. Case still stays closed with the other latches. It was that way when I bought it years back).

It was not until the large-scale emergence of small combo jazz in the post-WWII period that the guitar took off as a versatile instrument, which was used both in the rhythm section and as a featured melodic instrument and solo improviser. In the hands of George Barnes, Kenny Burrell, Herb Ellis, Barney Kessel, Jimmy Raney, and Tal Farlow, who had absorbed the language of bebop, the guitar began to be seen as a “serious” jazz instrument. Improved electric guitars such as Gibson’s ES-175 (released in 1949), gave players a larger variety of tonal options. In the 1940s through the 1960s, players such as Wes Montgomery, Joe Pass, and Jim Hall laid the foundation of what is now known as "jazz guitar" playing.


In 1932, John Dopyera left Dobro and came back into the National fold, regaining control of the company. We can only speculate that the absence of Beauchamp has something to do with his decision. National and Dobro merged in 1935, becoming the National Dobro Company. However, until the end of the ’30s, when National Dobro finally completed its relocation to Chicago, Dobro instruments continued to be made in L.A. by what had been the separate Dobro Corporation, even though it was a part of National Dobro. Got it? Hmmm…


Many web surfers contact me looking for a wiring diagram for an unusual / no name / import guitar after having no luck online. And sometimes you aren't going to find it, however, if you have an electric guitar that is similar to lets say a Strat ... it has 3 single coil pickups (and they are 2 wire pickups), one 5 way switch, 2 tone pots and 1 volume pot then you can simply use a Strat wiring diagram. It's often easiest to think of the instrument in terms of components not brand.
Guitar chords and signatures. Find and save list of chords. Basic guitar chords A sheet of the most used rock chords. Suitable for beginners. Empty chord sheet An empty sheet of chords templates to print out and use. Basic guitar chords Em, C, G, D, Am, E, and A Free lesson on the basic guitar chords Em, C, G, D, Am, E, and A. The following chords are 7 of the most basic open position chords. An open position chord is one that contains at least o
Makers of the Elk badged guitar from the early to mid 1960s to 1975, although other sources indicate that the Elk brand did not stop production until the early 1980s. Elk badged guitars came in clear acrylics in addition to colors in the early 1970s, which was an attempt to copy clear acrylics designed by the legendary Dan Armstrong in the late 1960s.
Next, you will need to adjust the intonation. In this case, the technique is pretty much the same. You will need a small Phillips screwdriver. On the tailpiece side of the bridge in the first case, or the rear of the bridge in the second, there are screws holding the string saddles in place. Check each note by striking the string at the twelfth fret fretted and then unfretted. The unfretted note is the proper one; turn the screws either clockwise or counter-clockwise until the notes match.

I consider Squier and Epiphone to be the two top brands beginners should be looking at for their first guitar. However, there are some key differences when it comes to their flagship instrumets. Where the Epiphones listed above have a pair of humbucking pickups, the Squier Stratocaster has a trio of single coils, and the Telecaster a pair of single coils.

wonderful feel of a small town, with caring people and the owner is amazing. He'll of a player too! Just got a gorgeous ESPN strat copy from him, he graciously showed me just how well of a strat it is... by playing it through a fender tweed tube amp. He even sang a little for me as he made my strat sing right along with him. Price was excellent, as are all his prices. See More
Values? Well, with the prices of 1960s American and British guitars through the roof, collectors and musicians turn to the next-best-thing, and that would be European and Japanese guitars. In general, any made-in-Japan solid-body electric guitar in good cosmetic shape, that's complete and playable, is worth at least $100, and any acoustic-electric, at least twice that. The more pickups it has, the more elaborate the controls, and the more flashy the pickguard, the more it's worth. Same goes for the body and headstock shape. The standard shapes that copy Fender and other manufacturers aren't as desirable as some of the weirder shapes. A Decca solidbody with an unusual body shape, with 3 pickups and an unusual original finish would probably be in the $250-350 range to the right person. An acoustic-electric with the same specs would probably be worth $100 more than that. I've seen some of the exceptional Teisco solidbodies go for $500-600, but that's uncommon. In about 2006, I saw a Teisco (one of their Mosrite copies) from about 1967 that was in flawless condition for sale in an instrument shop in Tokyo for 200,000 Yen (about $1,900). I wouldn't be surprised if it sold for that.

The reason: The dynamic range of music can exceed 60db (power ratio 1:1,000,000). Transients within the music can exceed 20db (power ratio 1:100). Therefore amps under 60Watts and ‘Single Ended Class A’ will not be discussed in this text. Valve amplifiers are used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS systems, audiophile stereo amplifiers, military applications (such as target acquisition and radar) and very high power radio and UHF television transmitters


Quirks? Some. The old Rola was kind of tired, so I saved it and put in a new Jensen Mod I had laying around (not a bad little speaker, but not a vintage Jensen, either…expect a future upgrade). The 7F7’s are supposed to be very loud and micro-phonic (which was why we don’t tend to see them in guitar amps after the mid-late 40’s), but this one sounds just fine. And they’re cheap, so it’s not like you’re hunting down good EL86’s or anything. Also, one thing that took some getting used to was the tone knob is backwards by contemporary standards. That is, turn the creamy chickenhead to the left, you get more treble (and more drive and volume). Turn to the right, and it gets very bassy and like a chewy jazzy tone.
In some modern valve effects, the "dirty" or "gritty" tone is actually achieved not by high voltage, but by running the circuit at voltages that are too low for the circuit components, resulting in greater non-linearity and distortion. These designs are referred to as "starved plate" configurations, and result in an "amp death" sound.[citation needed]
The Website attempts to display product images shown on the Website as accurately as possible. However, The Top Guitars cannot guarantee that the image or color you see displayed on your monitor represents the actual product or conforms to the specifications of the product you have selected. If you have any questions about product appearance/specifications, please contact us before placing your order. The Website does not contain images of each offered item because some of them are Custom and not built and/or modified yet.
There are a couple of tricks you can try. One is to get an allen key wrench that is SLIGHTLY too large and take a small file to it to taper all six sides slightly. The other trick, which I use sometimes on Stratocaster saddle height screws, is to use a suitably-sized Torx wrench. They're already tapered, and since they're six-sided-star shaped, they grip the corners really well, even if there's a bit of crud stuck in the screw.
Due to the acoustic, aesthetic and processing properties (workability, finishing, joints) the wood and the ligno-cellulose composites are the most valued materials for the musical instruments' construction. The guitar is made up of a complex structure, formed by a vertical wall in a curve shape (technologically named "sides") and two faces made up of ligno-cellulose plates, so that it should... [Show full abstract]
This is a no brainer, but a value that must be considered before any purchase no less. As mentioned above, your abilities on the instrument will likely affect the price range you’re looking at, which may have an effect on the brands you shop within as a consequence. For instance, if you’re not looking to buy a high end guitar, you probably won’t even bother testing out a Gibson, as their guitars will likely be out of your range. The reverse is true as well, an experienced player on the market for high end tone probably won’t be satisfied by many of Yamaha’s offerings.

The same no-compromise attitude that gives the Newporter Player its uniquely killer vibe extends to every aspect of its construction. It features optimized bracing for reduced mass and superior resonance, a Graph Tech - NuBone nut and saddle for greater sustain and a Fishman preamp system that makes it easy to plug in without sacrificing the guitar's natural sound. Its lightweight mahogany neck features a comfortable, easy-to-play, slim-taper "C"-shaped profile suitable for any playing style, and its walnut fingerboard and bridge further augment this instrument's vibrant tone.

Ampeg was swallowed up by Japanese electrical giant Magnavox in 1971, when they wanted to get in on the electric guitar copy craze of the 1970s. Magnavox produced electric and bass guitars under the Stud badge as well as the successful Ampeg brand. It's been suggested that Magnavox was also responsible for producing Selmer acoustic guitar badges during this time, but that has not been verified. Selmer was sold to Magnavox around the same time they bought Ampeg, so it certainly seems plausible they could have made Selmer acoustic badged guitars as an offering for that market. Stud badged guitars were made until '75, with Ampeg guitar production continuing until 1980. Opus was another badge made by the company. Magnavox lost their interest in Ampeg shortly thereafter and the brand languished until it was resurrected over a decade later by another American company.
In addition to building world-class custom basses and guitars, our luthiers also perform a wide variety of guitar repairs, restorations, modifications and upgrades. Whether you have an electric guitar, acoustic guitar or a bass, new or old, feel free to bring it by the shop for a free assessment. We have the experience, skill and equipment to provide maximum playability.

Like in the overall best-selling list, there are a few amps on this list which have been discontinued but continue to sell very well on the used market. Part of the reason these amps rank so high on our lists is that Reverb is one of the only places these models are still being sold, meaning that our sales likely account for a sizable chunk of the entire used market for these particular amps.

Here, in this mini guide to acoustic guitar body types, we’ll aim to show you some of the key differences in size, shape, sound and suitability between the major variations of guitar. We’ll look at the history of some of the better known body types, and make recommendations according to the sound you’re going for and the style in which you play. So whether you’re a wispy finger-picker or a hearty strummer, we’ll explain some of the more intricate details of acoustic guitar body shapes.


All I can say is quit wasting $ on new. A new guitar is like a new car it’s gonna lose 20% of its value once you take it out the first time. Unless you are buying a Gibson or fender custom shop etc Just go for what plays and sounds great. Perfect example is the Esp ltd ec401vf or 400. Used $300-400 has stock seymour duncan 59 neck jb bridge or the newer 401 has the dimarzio’s in it. Grovers tuners earvana nut mahogany body. Just an excellent setup for half the price of an epi les paul. Don’t get me wrong I have an Epi les paul traditional pro and it’s a nice guitar but for $750 nah. Since I picked up the 401 I hardly play my jag mustang or either of my epi l.p. or sg. Its just that nice of a guitar. If you are in the market for a les paul style or a new guitar in general take a look at the 400 series it’s a whole lot of guitar for the $
{ "thumbImageID": "GRX20-Electric-Guitar-Black-Night/519417000787000", "defaultDisplayName": "Ibanez GRX20 Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Black Night", "sku": "sku:site51275776901849", "price": "149.99", "regularPrice": "149.99", "msrpPrice": "214.27", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX20-Electric-Guitar-Black-Night-1275776901849.gc", "skuImageId": "GRX20-Electric-Guitar-Black-Night/519417000787000", "brandName": "Ibanez", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/GRX20-Electric-Guitar-Black-Night/519417000787000-00-60x60.jpg", "imgAlt": "" } , { "name": "Jewel Blue", "sku": "sku:site51275776902065", "price": "149.99", "regularPrice": "149.99", "msrpPrice": "214.27", "priceVisibility": "1", "skuUrl": "/Ibanez/GRX20-Electric-Guitar-Jewel-Blue-1275776902065.gc", "skuImageId": "GRX20-Electric-Guitar-Jewel-Blue/519417000085000", "brandName": "Ibanez", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/GRX20-Electric-Guitar-Jewel-Blue/519417000085000-00-60x60.jpg", "imgAlt": "" } ] }
{"id": "113900398", "categoryId":"site5ABA", "name":"Vintage Vintage 1960s Decca DM1-204 Natural Acoustic Guitar", "pageUrl":"/Used/In-Store-Vintage/Vintage-Vintage-1960s-Decca-DM1-204-Natural-Acoustic-Guitar.gc", "thumbnailUrl":"https://media.guitarcenter.com/is/image/MMGS7/Vintage-1960s-Decca-DM1-204-Natural-Acoustic-Guitar/000000113900398-00-180x180.jpg", "hasFeatures":"0", "isAccessory":"0", "message":"", "value":"179.99", "priceMin":"179.99", "priceMax":"179.99", "msrp":"", "productVisibilityMSRP":"1", "restockPrice":"", "openBoxPrice":"", "clearancePrice":"", "isPlatinum":"0", "priceSavingsMaxPrice":"0.00", "priceSavingsMaxPercent":"0", "inventory":"1", "brand":"In Store Vintage", "reviewStarImageUrl": "https://static.guitarcenter.com/img/brand/gc/cmn/Sprit-Sm-Stars.png", "reviewStarRating":"0.0", "reviewStarRatingInteger":"0", "reviewHowManyReviews":"0", "usedOrNew":"used", "discontinued":"0", "onOrder":"0", "clearance":"0", "canBeSold":"1", "accessoryCategories":"site5LFMID,site5LAAB", "stickerText": "Vintage", "isVintage": "1", "outletonly": "", "checksum":"134135816000", "priceVisibility": "", "itemType": "Vintage"}

The structure of the lessons are good, it varies between guitar technical stuff and theory as you progress, meaning that you won't get bored of any single topic, and you'll have a chance to try out the theoretical bits one step at a time. It's a shame they never made newer editions of this book with more graphics and supplemental audio-video tools.
Great condition. With the exception of the gold foil missing from the back pad, allowing the pink to show thru, the guitar is entirely original. Has a couple of small spots of edge wear, and a chip on the front, the size of this 'o'. Plays and sound fine. Has correct amount of neck relief (.010") at the 7th fret, when fretted at the first fret and the body fret. Includes original chipboard case.
When it comes to acoustics, you can’t beat Taylor’s eco-sourced Tone Woods. The 114e features a solid Sitka Spruce top and layered Sapele back and sides, giving the Taylor a rich and full-bodied sound that is hard to tell apart from solid wood bodies more than twice the price. The electrics and built-in preamp are top notch and you can’t beat that Taylor neck for finger-friendliness if you’re just starting out with chords.​
Ovation Guitars, in conjunction with the DW Music Foundation (DWMF) will debut the RS Rockstar™ guitar. This six-string, “RS” model guitar will be donated to each Notes for Notes location along with a DW drumset and an LP cajon to equip each studio with professional level musical instruments. The DWMF will also work with other partnering charities to donate RS Rockstar™ model guitars to music education programs in underserved communities worldwide.
OLD Morris looks to be equal in all respects to our Yairi CY116, exotic wood construction with very nice old woods and excellent workmanship - fit & f instance they make the fit & finish is amazingly nice on the Terada factory made Morris. If your not familiar with Terada they are responsible for some of the finest Japanese guitars on the planet for instance Ibanez George Benson GB10's and all that high end line, most of Ibanez's Artists, and several other top of the line Japanese legends and they know how to make exceptional guitars and this Morris Classical is no different it sounds beautiful and has the vibe that is if you love the looks and feel of a well seasoned fully broken in 40 year patina and your OK with the top finger drag wear your going to love this vintage beauty yes it has plenty of vibe bit it sounds deep and rich too. Nice meaty neck plays easily with great action and with absolutely no cracks oh it has minor doinks and scratches here & there but nothing horrible this guitar qualifies for a VERY GOOD JVG rating overall vintage excellent but with the wear as seen the neck is still pretty slick no major abrasions and the fingerboard is nice too. Yes this is a very nice Ole Classical that has another lifetime of wonderful service to its new owner. I think you will be very pleased. Any questions just drop me an email to JVGuitars@gmail.com . Thanks for looking Joe.

Delay is a commonly-used effect where the pedal repeats your sound at pre-determined intervals after you’ve played it. It’s used almost exclusively with a clean guitar sound, although can be employed as a kind of quasi-reverb sound to flesh out a guitar solo using a driven sound. Predominantly though, musicians love delay because it’s a brilliantly creative tool where ideas can start coming out of nowhere just through experimentation. By setting the repeated sound to play back at longer intervals via your delay pedal, e.g. around a second or longer, you can play a note and then embellish it with other patterns before the original note has even played back. This type of effect lends itself well to solo playing, as evidenced by its more advanced sibling; loopers.
This is Yamaha’s C40II classical guitar, an inexpensive nylon-strung guitar that’s a cut above some of Yamaha’s even cheaper models designed for schools and the like. Many companies offer a line of low-priced, very basic designs tailored for education facilities. Don’t go that far down the price pecking order. The C40II for $140 USD on Amazon is a good compromise. Please do yourself a favor and get the $13.58 two-year protection plan!
The Line 6 POD Farm program is famous for its amp simulation, however many users have realized that the quality of its modeled effects are equally superb. Some even use the POD Farm strictly for its effects! It has a huge collection of FX - up to 94 - and it modeled some of the most popular stompboxes including the MXR Phase 90, ProCo Rat, Uni-Vibe, Arbiter Fuzz Face and Big Muff Pi. It also includes modeled versions of old analog devices like the EP-1 Echoplex. Setting up is a breeze with its simple carousel-style interface, which lets you visualize your signal chain. Current Retail Price $49.00
Before you start thinking your pickups can kill you, bear in mind this is a very small signal (2 volts) that requires amplification (this is where your aptly named guitar ‘amplifier’ comes into play). To put things in perspective, the little rectangle shaped batteries (D) found in distortion pedals are 9 volts…as mentioned it’s a very small signal.
Other specs on the guitar are similarly metal-inclined. It has a fast Nitro Wizard neck profile and a very flat 15.75-inch-radius ebony fretboard, a Gibraltar Standard II bridge that improves string resonance, and Gotoh MG-T locking machine heads for tuning stability. And a single master “Volume” knob ensures nothing gets in the way of your shredding and riffing acrobatics.
A Flanger simulates the sound effect originally created by momentarily slowing the tape during recording by holding something against the flange, or edge of the tape reel, and then allowing it to speed up again. This effect was used to simulate passing into "warp speed," in sci-fi films, and also in psychedelic rock music of the 1960s. Flanging has a sound similar to a phase-shifter, but different, yet is closely related to the production of chorus.
Editor’s Note: My previous top choice, the Yamaha APX500iii, is now replaced with a newer and better model, the Yamaha APX600. What make’s it better, you ask? Well, there were some complaints regarding the previous model for having a lack of bass response and a “bland” sound when unplugged. Yamaha addresses this issue by changing the guitar’s bracing pattern, thus improving it’s overall sound response, making the APX600 a good choice for an acoustic-electric guitar. I suggest you go check this bad boy out.
The Kremona “Sofia” model is handmade in Bulgaria as well with a fantastic support staff to answer any questions, so if you have concerns about items made in China, you can lay those concerns aside. The top is cedar, with an authentic bone nut and saddle, and solid African sapele back and sides complete the look for a very pleasing appearance and sound.
Yamaha is one of those names that you don’t often see outside the realm of keyboards and digital pianos. While their footholds in fairly limited on the stringed instruments market, their quality is well known. Yamaha builds some of the most balanced and best performing electric guitars in their respective categories. That is simple the truth. Now, they might not be as popular as other brands, but that is a whole different story.
Also, you need to always remember that you will need guitar accessories and essential that specially designed for your electric guitar like a strap, picks, and gig-bag, in addition, a good practice amplifier. On the other hand, probably you don't need to worry as you do get almost all of such thing as the part of a bundled package deal at the time you are shopping for a new one.
Anyone without the skills and ability to shred well technically should not be on a top list ever. Any top list without Buckethead is incomplete since he has the highest ability. Anyone that says Buckethead can not play with soul/feel/emotion/blah blah blah are misinformed and have not listened to enough of him them self. Buckethead has over 50 albums so it is hard to find the good stuff since a lot of his work is experimental, but his good stuff is the best stuff. Oh wow just before pushing post I just found yet another awesome older Buckethead song… Brazos.
The EB-18 was not all that popular among bass players, and total production has been estimated at 874. The more expensive follow-up model, the EB-28, was even less popular with a total production of 217 units.[16] See also: E-18 series guitars[17] Martin did not resume building basses until 1989 (during the MTV Unplugged era), in which their approach was more consistent with company history:
i have a grand total of 1 pedal. it's an overdrive pedal that i only use when playing heavier songs. Other than that, i tend to play just guitar and amp. My amp has reverb and i tend to set that at about 1/3 the way round. Does that count as effects? My settings are set just on the edge of break up so i get a nice clean tone, but when i hit it harder, it gives a little crunch.
I personally use Vegas, Sonar, and REAPER. I would not recommend Vegas or Sonar for live playing, if for no other reason than both have crashed on me during recording sessions, and I do not easily forgive that. REAPER (Audio Production Without Limits) never, ever crashes. It’s not as full featured as some DAWs, but what it does, it does well. I use it for all my recording.
Lydia Lunch once beat her Teenage Jesus & the Jerks bandmates with coat hangers during practice; and her confrontational attitude was only matched by her completely unfettered guitar playing. Calling the instrument “a grand assaultive weapon,” she treated it as such, often attacking the strings with knives or even shards of glass, refusing to even bother learning chords, using it as a blunt force to express a total anti-pop, anti-punk, anti-everything rage.

Another negative I found was that this book focuses more on traditional music notation, and places guitar tablature into the background. As a guitar teacher, I believe that tabs are the next best thing to sliced bread, since it makes learning soooo much easier for beginner guitarists. And since learning the guitar is hard, anything that makes it simpler is more than welcome. On the other hand, if you want to learn to read standard music notation, this will be the way to go for you.
In 1941, CMI became the national distributor for National Dobro products. In ’42, Victor Smith, Al Frost and Louis Dopyera purchased controlling interest in the company. By this time, however, the world was at war and almost all instrument manufacturing ground to a halt as all segments of industry converted to production of materials to support the war effort. In October of 1943, with builders in wartime hiatus, the new owners changed the company name to Valco Manufacturing, incorporating the first initial of each partner’s given name (V-A-L-Co).
Semi-acoustic guitars have hollow bodies which give them a warmer and more dynamic range of sounds. They are vulnerable to unwanted feedback as the distorted sound increases the chances of feedback. That’s why we don’t see rock and metal musicians playing a semi-acoustic guitar. Many guitars have solid blocks inside for decreasing the feedback factor. Check out our list of semi-acoustic electric guitars here.
As a guitarist with a complete understanding of the vintage instruments he worked on, Novak wasn't completely comfortable with what any one instrument was capable of delivering. He wanted to combine all the features of his old favorites while adding design twists that would give him everything he was looking for in an electric guitar. This led to the invention of his patented fanned-fret fingerboard, which gives an instrument combined scale lengths.

I always recommend the Cordoba C5 for beginners who are looking for their first classical or nylon string guitar. It’s comes at a very wallet-friendly price, but it sounds and plays exceptionally well for a guitar in its price range. More experienced players can look to other C-Series Cordoba guitars like the C12, which is built for advanced guitarists.
Though because of this flexibility, it can be hard to figure which of the many types of electric guitar is going to be a good fit for your needs. Thankfully, if you’ve arrived at this article you’re going to get all of the information that you need to make an informed decision on which body styles are going to be worth considering for your genre of choice.
Taylors are okay as guitars go, but... I've owned three, sold them all in mint condition and lost considerable coin in doing so. I think they belong on this list because they charge hand made prices for MASS PRODUCED guitars. Don't believe me? Take the Taylor that you own and do a search for it on eBay. That's right, at this very moment there are hundreds of guitars just like yours for sale on eBay. And that's only checking this one sales venue! These guitars are worth half of what you paid because the market is saturated with them. Taylor cranks out hundreds of them per day and 100's of thousands per year. If you're shopping and seriously considering a Taylor, you can get comparable quality and far better value elsewhere. Choose carefully and you'll see your investment go up in value. Aside from some special, collectable models of Taylor, you will loose money on this brand.
Now we switch gears to a company called Unicord, which was owned by Sid Hack. At some point in the early ’60s (probably in around ’64), Unicord purchased the Amplifier Corporation of America (ACA) which was located in Westbury, New York, a northern suburb of New York City. ACA made Haynes guitar amplifiers and an early distortion device powered by batteries.
In launching the AZ series, the goal was not to merely create a completely new guitar model, but to sculpt a great guitar that can foster the potential of the modern ?third phase' while maintaining traditional elements. Even though Ibanez is thought of as a modern guitar brand, it has decades of accumulated knowledge and a history of pushing the boundaries. The AZ series carries with it all of the hallmarks of these tried and tested Ibanez qualities. The harmonic balance between bridge and ...

SOLD ; Fresh releas from the JVG Vintage Vault collection.....Here she is a wonderful sounding Exotic tone woods LawSuit model Takamine from the PeaK and end of this so called Lawsuit copies. What can I say this beauty has it all the Exotic Tone Woods the beautiful TONE the superior workmanship this example exhibits the care from its one owner. Its condition is better than average it has no cracks, no checking, no warping nothing to report, it does have a very few minor chips or dinks overall way better than average not exactly new or mint like its overall gorgeous and is easily a solid 9.5/10 used vintage excellent, its neck is arrow straight proper relief is set and action is beautifully low and it makes playing this beauty a dream like pleasure. She's been professionally set up with a new set of Martin strings. Intonation is dead on and she rings like a bell. Very rare to see this model up for sale and available to buy this guitar is Amazing and is a keeper.... SWEET! Contact Joe to buy it at: JVGuitars@gmail.com Thank you for looking.
If you just start playing into a Windows PC, you’re going through a software construct called an audio device driver, through another software construct called the Windows Mixer, and finally into your recording program. If you then loop that back to play out so you can hear your guitar plus all effects, you again go from that DAW program to the Windows Mixer and to the device driver. That can take a really, really long time in music terms.
One of the things that initially surprised me was that coincident dual-mic techniques, where the two mics are placed as close as possible to each other to minimise phase cancellation between them, actually appear to be more commonly used than single-mic techniques. John Leckie explains: "There's an amazing difference in the sound and colouration you get from adjusting the balance of each of the mics, and you can get radically different textures depending on your mix of the two."
After the dissolve of Kay/Valco in 1968, the Engelhardt-Link company bought the upright bass and cello lines[clarification needed] at the asset auction in 1969, and continue to produce the same instrument lines till today. Manufactured in Elk Grove Village, Illinois, Engelhardt basses and cellos are sturdy instruments, widely used by students and touring professionals. The ES9 Swingmaster bass (formerly the Kay S9 Swingmaster), is highly thought-of by jazz, swing, and bluegrass musicians.

Equalizer: An equalizer is a set of linear filters that strengthen ("boost") or weaken ("cut") specific frequency regions. While basic home stereos often have equalizers for two bands, to adjust bass and treble, professional graphic equalizers offer much more targeted control over the audio frequency spectrum.[64] Audio engineers use highly sophisticated equalizers to eliminate unwanted sounds, make an instrument or voice more prominent, and enhance particular aspects of an instrument's tone.[65]
“Volume pedals work well just before any delay or echo effects, as you can fade in and out of delays smoothly. A volume pedal at the very end of the chain just before the amp input will control master volume, and can also be used as a mute. Reducing the signal at this point will also reduce any noise. I put clean boosts right at the end—also just before the amp input—to ensure that any effects earlier in the chain would not be overloaded.”
In August ’68, Ovation added three more models – the Hurricane 12-string and the Typhoon I and II basses, all with chrome hardware. The K-1120 Hurricane was a Tornado with the extra strings, advertised as offering a “harpsichordian” effect. This lasted only a year and was gone by ’69. The initial Typhoon basses had slightly smaller bodies than the guitars, with stubbier, more flared horns. These lasted only a year until ’69, when the body styling changed to that of the Gibson-style guitars. The K-1140 Typhoon I bass had one Schaller pickup and a covered bridge/tailpiece assembly. The K-1240 Typhoon II was a two-pickup model with a three-way select. This was also called the Williwaw (“mountain wind”) in some Ovation literature, but it was never really called that. The Typhoon I was only available in the stubby body and was discontinued in ’69. The Typhoon II changed model number in March ’70, becoming the K-1222. This model made it until June ’72.

In choosing an amp you have to first consider how much you have to spend, the style of music you like to play, and what kind of tone you like best. It is perhaps best to start with something small. You might feel that a Marshall stack is the way to go, especially if you have the money, but for home use, big amps are hard to work with because to drive them into distortion, you have to get really loud. They also take up a lot of space.
Also joining the Univox amp line in ’71 (illustrated in a ’72 flyer) was the Univox U-4100 Minimax Amplifier, already showing a different style, with dark tolex covering but still the oval logo plate on the upper left of the grille, now covered in black with vertical “dotted” lines (surrounded by a white vinyl strip). The Minimax was designed for use with bass, organ, electric piano or guitar, but really was a bass combo amp. It packed 105 watts through a 15″ Special Design speaker with 27-ounce Alnico magnet and 21/2″ voice coil, powered by 11 transistors, no tubes. The back-mounted chassis had two channels with high and low inputs, plus volume, bass and treble controls for each channel. Recommended especially for keyboards was an optional UHF-2 High Frequency Horns unit with two horns for extra bite. The flyer for this amp was still in the 1980 Unicord book, but a ’79 price list no longer mentions it, and it was probably long gone, though some may still have been in stock.
Based both in Japan and the USA, this Japanese manufacturer produces guitars under different brand names: "ESP Standard," "ESP Custom Shop," "LTD Guitars and Basses," "Navigator," "Edwards Guitar and Basses," and "Grass Roots." Hisatake Shibuya opened his "Electric Sound Product" store in 1975 where he used to sell guitar spare parts. He then started to build his own parts and became a Kramer and Schecter subcontractor. His first signature guitar went to George Lynch (the Kamikaze), while the powerful Gibson Explorer copy designed for metal heads and adopted by a certain James Hetfield (Metallica) became almost as popular as its owner in the late 1980's and early 1990's.
Another tone option for a guitarist is to put a pickup out of phase with another pickup, producing a thin "inside-out" squawky kind of sound. When 2 pickups are in phase, they work together and reinforce each other. When they are out of phase the 2 pickups are working against one another and the resulting sound is the "leftovers" from these cancelations. The closer the 2 pickups are, the greater the cancelations, the thinner the sound and the lesser the volume. Therefore, the neck and bridge pickups out of phase is the best choice for this type of sound.
Conklin: Conklin is a quite well known brand in the world of high end custom shop guitars. The level of customisation they offer is absolutely amazing. They offer their own body designs or you can submit your own custom body design, as far as design is considered, with Conklin your imagination is your limit. They also offer melted top wherein they combine two or more woods in a seamless way to create a top that looks as if woods have melted into each other, but they don’t stop only at beautiful tops, they even offer option for melted fretboard wherein two are more woods are beautifully combined to create a masterpiece for a fretboard. They use Lundgren pickups as their standard choice. You can even order guitars with special switching configuration customised to your liking. Their neck-through guitars are just excellent, even their bolt-on neck guitars are set precisely and have a nice tapered neck joint which makes you feel as if you’re playing a neck through guitar. The level of craftsmanship on these guitars is just mind-blowing.
In the early 1980s, some performers began using two-way or three-way cabinets that used 15" woofers, a vented midrange driver and a horn/driver, with an audio crossover directing the signal to the appropriate driver. Folded horn bass guitar rigs have remained rare due to their size and weight. As well, since the 1990s, most clubs have PA systems with subwoofers that can handle the low range of the bass guitar. Extended range designs with tweeters were more the exception than the rule until the 1990s. The more common use of tweeters in traditional bass guitar amplifiers in the 1990s helped bassists to use effects and perform more soloistic playing styles, which emphasize the higher range of the instrument.
On the same topic, if you do apply some compression during recording, be careful not to overdo it. At this stage, you don’t need to hear any effect, it should just transparently control peaks. If you apply the amount of squeeze that may be needed for the mix as the part is going down, it might cramp the player’s style—better to leave that for later. Plus, if the signal is over-compressed here, it may bring out the normal squeaks and finger & fret noises so much that it becomes difficult to eliminate them later—this is especially true if the player is really a guitarist who also moonlights on bass. Guitarists who try their hand at bass parts often haven’t mastered an experienced bassist’s technique for damping the strings, and the little playing noises I referred to, as well as distracting undamped harmonics, can end up overpowering the recording if heavy limiting/compression brings them up (I recently struggled mightily to deal with a bass track that suffered from this flaw).

A. Many professional musicians invest thousands of dollars in high-end guitars made from expensive and rare tonewoods. A $100 student guitar made from spruce is not going to produce that level of tonality regardless of the player’s skill level. As a beginner, your main focus should be on skills such as chord formation, fretting techniques, and basic scales. Improving tonality and performance are long-term goals.
Okay, it is a single-cut and dates back to a similar era, but this single-cut is very different to a Les Paul. The Pro Jet has a basswood body with an arched maple top, and like many of Gretsch’s solidbody electrics, it’s chambered, making it lighter, and, they say, more resonant. It sports a pair of Gretsch’s Black Top Filter’Tron pickups, giving you a bright snap and twang that’ll cut through any mix. In short, it’s incredible. Uncanny, even. For here we are in 2018, and yet you fret a couple of doublestops on the Pro Jet Electromatic and all of a sudden it’s like you’re the Fonz, just waiting for Richie, Joanie and Chachi to show up. The cleans are sharp and jazzy, but just take your amp into overdrive and you’re in rockabilly heaven. The tone is so hot you could grill hamburgers by wafting it in front of the speaker cone. Tex-mex shuffle, country, blues, jazz, rockabilly... You name it, and it’ll play it, retro-style. if you want the versatility and the kudos that comes with a Gretsch, it’s hard to look past that finish, that build, and that tone.

The design, while nothing particularly special, is clean and beautiful, which will help it appeal to most guitarists - the dreadnought acoustic body being one of the favorite parts. Ultimately, just about anyone could pick up this guitar and get what they need out of it, which is why it makes our top pick. We could recommend it to anyone, and when you talk about the price, it becomes even more attractive, because this is a high-end guitar for mid-range money.
Amazing guitars, specially the Custom Series full solids. You can choose from variety of tonewoods and soundboard combination and 4 different shapes. Offering almost every player's preference. You can also choose options such as soundport off-the-rack. Great craftsmanship, amazing tone, and superb playabality at an amazing price. Great guitar, and definitely not an OEM brand. They only make their own guitars.

1. Intonation: I have a brand-new Epiphone LP that will not completely intonate on the G, A, and Low E. Fretted notes remain sharp. I have replaced the factory strings with new Ernie Balls and tried every trick in the book to move the saddles as far away from the neck as possible. Many LP owners have this problem. Other than returning the guitar to Guitar World, my only other option is swap out the factory bridge with a wider one. You mention the latter option in one of your early comments, and I've decided to try it. I just bought a Gotoh one online. Hopefully, that will solve the problem.


This bass guitar amplifier features a 20-watt amplifier and an 8-inch driver. It reproduces frequencies from 70 Hz ~ 10 KHz with a total harmonic distortion of 0.5% (typical). It also has a built-in, switchable active compressor. It features a 3-band EQ, with the bass EQ centered at 100 Hz, mid-range EQ at 800 Hz, and a treble EQ at 6 KHz. It features a 3.5mm line output with an impedance of 1 kilohm, for directing the output signal to a mixer, recorder, or another amp. The 3.5mm stereo headphone output will defeat the internal speaker for quiet practicing.
Pickup selectors can wear out over time. The lugs and the rotating switch can loose their tight connect with years of use. Also, many inexpensive guitars made today use cheap electronic parts. You may just want to upgrade your switch for more control and better selections. It is fairly easy to install a new pickup selector. Here are a few simple steps to replacing your pickup selector.
Electric Guitars- Vintage, new & used / Second-hand electric guitars by Kay, Teisco Del Rey Ray ET J-1, Univox & Silvertone. Cheesy Japanese, Surf Guitars. Also guitars by Ibanez, Gibson, Fender, Peavey, Martin, Zon, Gretsch, Rickenbacker, Diasonic & More. Les Pauls recording, lap steels / slide guitars, Barney Kessel style, Fender Stratocasters, Telecasters, Squire Bullet series, Peavey Falcon neck Martin Acoustics, bass guitars, Zon Legacy Elite 5 string Bass, Diasonic double single cutaway, Rickenbacker, archtop, Gretsch TW-100T Traveling Wliburys guitar, Hamer Mirage 1, Yamaha sg-2000, Fender Jag-Stang, Gibson Howard Roberts, Ibanez Artist AR-100 to name a few.
After Fender’s decision in 1982 to switch Squier’s production from strings to guitars, the Stratocaster was one of the first models put under the Squier production line in Japan. It was the most commercially successful guitar Fender had produced. Originally in 1982, the headstock had a “Fender” name written in large script, followed by “Squier series” in smaller script. In 1983, this was later changed to the current 1970s large headstock featuring “Squier” in larger script, followed by “by Fender” in smaller script. Since then, there have been several variations of headstock size and Squier logos, typically based on what series the guitar is.

The Fender Hot Rod Deluxe or its big brother the Deville come to mind. I have a hot Rod Deluxe tube mode 40 watts and it really pumps out the volume. The simple foot switch allows four settings from clean, mean, beyond mean and in your face. It really makes slide guitar sound like a male cat calling to a female in heat. Also, it can be mellow. I have seen many youtube videos with Eric Clapton playing a Tweed Model. I also own a Line 6 Duo Verb, Line 6 DT50, and of course and old US Made Peavey 5150 Eddie Van Halen Signature Model. The Peavey really pumps up the heat and the sustain is as wide as the Grand Canyon.
Rickenbacker manufactures three distinct pickups for their current standard models: Hi-gain, Vintage Single Coil Toaster Top, and Humbucking. All three pickup designs share the same footprint, allowing them to retrofit into most current or vintage models. The tone varies from one style to the next, partially because of the types of magnets used[13] but also due to the amount of wire wound around the pickup’s bobbin.
{ "thumbImageID": "1984-Explorer-EX-Electric-Guitar-Alpine-White/H77720000002000", "defaultDisplayName": "Epiphone 1984 Explorer EX Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Alpine White", "sku": "sku:site51316049519074", "price": "749.00", "regularPrice": "749.00", "msrpPrice": "1,248.00", "priceVisibility": "1", "skuUrl": "/Epiphone/1984-Explorer-EX-Electric-Guitar-Alpine-White-1316049519074.gc", "skuImageId": "1984-Explorer-EX-Electric-Guitar-Alpine-White/H77720000002000", "brandName": "Epiphone", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/1984-Explorer-EX-Electric-Guitar-Alpine-White/H77720000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Ebony", "sku": "sku:site51316049519054", "price": "749.00", "regularPrice": "749.00", "msrpPrice": "1,248.00", "priceVisibility": "1", "skuUrl": "/Epiphone/1984-Explorer-EX-Electric-Guitar-Ebony-1316049519054.gc", "skuImageId": "1984-Explorer-EX-Electric-Guitar-Ebony/H77720000001000", "brandName": "Epiphone", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/1984-Explorer-EX-Electric-Guitar-Ebony/H77720000001000-00-60x60.jpg", "imgAlt": "" } ] }
Rule 1—There are no rules. The sound you’re after might not be made by what we could call the appropriate or logical signal path, but that’s not always the issue. The issue is this: what does it sound like? If it makes the sound you’re after, then it’s right…although, you may have to do something about the noise. Traditional pedal board arrangements were designed for certain reasons, and keeping the noise down is one biggie. Following the principles of how sound is made in physical space is another (see Rule 4 coming up). But the final choice is yours. As a very wise man said: if it works, don’t fix it.
Most overdrive/distortion pedals can be used in two ways: a pedal can be used as a "boost" with an already overdriven amplifier to drive it further into saturation and "color" the tone, or it can be used with a completely clean amplifier to generate the whole overdrive/distortion effect. With care - and with appropriately chosen pedals - it is possible to "stack" multiple overdrive/distortion pedals together, allowing one pedal to act as a 'boost' for another.[44]
Another well established brand FMIC i.e. fender musical instrument company is widely recognized for manufacturing eminent guitars of superlative quality and texture. In India, the customers are satisfied form its products and won over millions of heart by providing brilliant guitar brands like FA – 100.So why waiting more? Quick make your purchase and enjoy the lovely music tone.
If you stick to a simple chromatic scale (all the semitones), you also run the risk of the pitch correction moving the audio to the wrong note if the singer is more than half a semitone off pitch. A user scale, containing only the desired notes, generally works much better. Some systems also allow you to dictate the correct notes via MIDI. If the song contains sections in different keys or that use different scales, it is often simplest to split the vocal part across several tracks and then use a different pitch-corrector on every track, each one set to the appropriate scale for the section being processed.
The bass guitar has a long neck (scale-length) and thick strings. The open strings of the bass guitar corresponds to the four lowest strings of the guitar and are pitched an octave lower. The standard bass has four strings though five and six string basses are available which extends the range of the instrument. Though the bass guitar is the bass instrument of the guitar family and the double-bass is the bass instrument of the orchestral string family their similar roles have drawn bass players to both instruments.

{"pageName":"[gc] pdp: ibanez artstar as153 semihollow electric guitar","reportSuiteIds":"guitarcenterprod","prop2":"[gc] shop: guitars: electric guitars","prop1":"[gc] shop: guitars","events":"event34,event3,event45,prodView","evar51":"default: united states","list1":"24-month,36-month,60 month","prop5":"[gc] shop: guitars: electric guitars: semihollow and hollow body electric guitars","prop6":"[gc] shop: guitars: electric guitars: semihollow and hollow body electric guitars","prop3":"[gc] shop: guitars: electric guitars: semihollow and hollow body electric guitars","prop4":"[gc] shop: guitars: electric guitars: semihollow and hollow body electric guitars","products":";H91419;;;;evar65=Blemished-Guitars-Ibanez","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] product detail page"}
Repairing pickups. You do not have the option of repairing and salvaging the pickup beyond re soldering the coil wire. If you do this be aware you are not repairing but instead customizing. However, to repair or restore pickups start by re-magnetize the coil magnets using strong earth magnets. If you need to re-solder the coil wire, unwind the pickup tape and properly re-solder in the wire appropriately.

A bass equalizer is the most commonly used of these three effects. It adjusts the frequency response in a number of different frequency bands. While its function is similar to a tone controls on an amplifier, such as rudimentary "bass" and "treble" frequency knobs, it allows for more precise frequency changes. A rack-mounted bass equalizer, for example, may have ten sliders to control the frequency range encompassed by a regular "bass" frequency knob.
: I have a similar guitar to the one you bought. It was my grandmothers and I'm estimating it at over 30 years old. Very folk style. She told me she actually had the original strings from when she bought it! I believed her when i tuned the thing and the day after found that the 4th and 6th had snapped. From what i know, Decca just made guitars around that time, 60's to 70's. Mine says it has a steel reinforced neck and it is really heavy compared to others. its still in really good shape and I actually play it. I'm not planning on selling it but I know its well worth its age. It has a hand chissled Ser. # on the bridge.

Frets & Necks did an AMAZING job on my RG7421. They installed my BKP Black Hawk p/u's and new tone/volume pots. Frets & Necks service was above and beyond, fast and super knowledgeable. I am very pick...y about who works on my guitars, I am beyond pleased that I chose Frets& Necks to work on my RG. I will be bringing my RG7421 back to Frets & Necks for future upgrades very soon. Be good to yourself and treat your guitar, give Frets & Necks a try. You won't be disappointed. Thank you F&N. See More
Heritage Guitars, founded in 1985 by four long-time Gibson employees when Gibson relocated to Nashville, continues to build guitars in the original factory at 225 Parsons Street inKalamazoo, Michigan. Many of their models evoke memories of Gibson’s late-1950s/early-1960s “golden years.” The H-150 and H-157 are reminiscent of the original Les Paul and Les Paul Custom, while the H-535 is a modern version of the Gibson ES-335.

Another piece of advice most experienced guitar players will give you is to keep your reverb pedals near the end of your signal chain. The reason for this is simple but requires a more colorful explanation. Imagine your signal chain as a conveyor belt for ice cream. As the signal leaves your guitar, it is just a plain vanilla mass that gets another layer of flavor as it hits different pedals. Distortion might add a nice chocolate glazing, then we have the modulation with its meticulous icing, and so forth. A reverb pedal in this context are sprinkles. You don’t want to add them at the beginning since they can completely change the way every other ingredient that comes afterward behaves. You add sprinkles at the end. In appropriate amounts only.
While most single-coil pickups are wired in parallel with each other, it is possible to wire two or more of them in series, producing a fuller and stronger sound not unlike that of a humbucker.[26] This is a popular modification for instruments with two single-coil pickups like the Fender Telecaster and the Fender Jazz Bass. For the former, special 4-way switches are available to replace the stock 3-way switch and provide a series wiring position.[27]

Some steel-string acoustic guitars are fitted with pickups purely as an alternative to using a separate microphone. They may also be fitted with a piezoelectric pickup under the bridge, attached to the bridge mounting plate, or with a low-mass microphone (usually a condenser mic) inside the body of the guitar that converts the vibrations in the body into electronic signals. Combinations of these types of pickups may be used, with an integral mixer/preamp/graphic equalizer. Such instruments are called electric acoustic guitars. They are regarded as acoustic guitars rather than electric guitars, because the pickups do not produce a signal directly from the vibration of the strings, but rather from the vibration of the guitar top or body.
×