Hopefully now you have a good idea of what to look for in a multi-effects pedal, and what criteria we judge one on. We made this list by going through dozens of forum threads asking for best multi-effects pedal recommendations (we ended up with an initial list of 45 different recommended pedals), and tallying up the ones mentioned the most. We then researched the top 5 by reading as many user reviews as we could find, and went out to test the top 5 ourselves. Here are the winners.
The cost: The original G&L scheme calls for alternate pot values, but the project here uses the 500K pots found in most humbucker guitars, so all you need are wire, solder, and a few capacitors. On a three-knob guitar, you wind up with one master volume control and two master tone controls, but you sacrifice individual volume controls for each pickup.On a four-knob guitar, you still have independent volume controls, but you lose the independent tone controls.
Very large cabinets, such as 8x10" cabinets, may have both wheels and a long "towel bar"-style handle to facilitate moving the equipment. Some 8x10" cabinets have handles on the top and bottom to facilitate two-person carrying of the cab. Some combo amplifiers have wheels and a retractable carry handle, to enable bassists to walk while pulling their bass amp; this can enable bassists to walk onstage with their bass and amp or walk to a venue with their gear.
So, if you’d like to emulate some of the guitar greats like Jimmy Page (Led Zeppelin) or Slash, this Epiphone package again with all the extras you’ll need—but with an Epiphone guitar—is a great way to start. Also, it’s worth mentioning that Gibson/Epiphone Les Paul designs usually have a slightly rounded, more narrow fret board and, in my opinion, are a little easier to play compared to the flatter, wider Fender fret boards. But I strongly recommend you don’t take my word for that. Get into a music shop and try the two types of guitar for yourself.
It also includes a -6dB/oct low-pass filter that’s built into the plugin’s tube/valve modeling equation, and can imitate a lower-quality tube triode. There’s a switchable output saturation stage, which can be used to overdrive the output signal and all the standard Voxengo plugin features, such as full multi-channel operation, channel routing and built-in oversampling. It’s great for guitars and for dirtying up sounds such as vocals, drums or synths.
In the Guitar Setup course, the third DVD is devoted to acoustic guitar setup. Acoustics are very, very different than electric guitars, when you get right down into the mechanics of them, and as such they truly do need a section of their own in any guitar setup guide. You’ll learn how to setup the action and intonation properly on your acoustic, as well as many other tips and tricks that will help you keep it in top working order.
Bracing affects the way the guitar sounds because it changes the pitch or tune that the guitar produces out of the sound hole. Personally I think X bracing is the b est because it produces a more even and better more balance for mids and high notes and just enough bass on the E and A strings that gives a brighter more even tone. Blinded or pessed bracing gives a much deeper sound than x bracing which =less versatility but if you bought a pressed dread knot or anything else you'll still be okay just remember strings make a huge difference and running your guitar to the right amount of tone for any song will work it's just that Taylor produces the best over all guitar itself by better quality woods and they go through ver strict and rigorous testing and inspections before they are sold to retailers and customers. Higher grade parts attention to detail and style of music versatility is why one guitar can cost 3 times as much. Most companies like Taylor is know give warranties or $ back
As music professionals, we're all familiar with guitarists and the rows of pedals they set up on stage at every gig. They're definitely on to something when it comes to effects on-the-fly, but when you're setting up a studio or pro audio rig, there's a simpler solution: multi effects processors. These full-sized units bring a ton of versatility to the table (or, more accurately speaking, the rack) and they can play a crucial role in shaping your own signature sound.
While larger frets do seem to result in a rounder tone, perhaps with increased sustain too, they also yield a somewhat less precise note than narrower frets—at least, as examined “under the microscope.” Unless it is very precisely shaped, and frequently dressed, the broad crown of that jumbo fret can “blur” your note ever so slightly, which might even be part of the sonic appeal for some players—the way, for example, a tweed Deluxe is a little blurrier or hairier at most volume settings than a blackface Deluxe. Be aware, however, that the phenomenon can work against some sonic goals too.
Continuing to look at the well-known Fender brand, the Stratocaster American Standard is a higher-priced option with necessary features for the seasoned guitarist. This is another one of the most popular electric guitars ever. In terms of build, the body is a mix of ash and alder, creating a balanced tone for both the sharpness of the upper range chords and the dense resonance of the lower range progressions. The modern bridge has an upgrade of utilizing a block infused with copper and steel saddles for strong intonation and an ease in adjusting pitch. The tuners are placed at varying degrees and heights, with this staggered design creating a decreased in reverberation and excess hum so as to focus in on the clarity of the sound. This electric guitar also has a custom designed single-coil strat known as the “Fat ‘50s”, which is intended to create a fuller sound compared to other guitars. With a comfortable ‘C’ shaped design and durable finish, this 22 fret guitar offers desirable features for the guitar enthusiast. If you’re unsure whether to grab this or our previous Fender pick, read this Telecaster vs. Stratocaster sound article for some more info.
This group contains two effects pedals, which are the noise gate and compressor (and most of the time a volume pedal). You don't want to change that ordering, because of the result of compression. It reduces the variance between the highest peaks of volume and the lowest. And if you haven't taken the noise out of your signal yet using the noise gate, your signal-to-noise ratio becomes lower, making it more difficult to take out the noise in a musical fashion (it'll have more abrupt and noticeable moments of silence).
REGOLAZIONE DELL'INTONAZIONE (FAT20) Per garantire l'assenza di movimento, ogni selletta è provvista di una vite di fissaggio. Per regolare l'intonazione, allentare la vite di fissaggio della selletta con una chiave a brugola da 2 mm (D). Per regolare l'intonazione, inserire una chiave a brugola da 2,5 mm nella vite della selletta sul retro del tremolo.
Jeff Beck: select alder body with a thinner C-shaped maple neck, contoured neck heel, rosewood fretboard with 22 medium-jumbo frets, three dual-coil Ceramic Vintage Noiseless pickups with 5-way switching, LSR Roller Nut, Schaller locking tuners and an American 2-point synchronized tremolo with stainless steel saddles. Available in Olympic White and Surf Green finishes (Artist Series, Custom Artist), as well as a “Custom Thinskin Nitro” version with a “Thinskin” nitrocellulose lacquer finish.
Their LP models have a "mahogany" body, and the binding is very thin so I think the maple top is just vaneer. I also noticed the headstocks were not the usual LP angle. In my opinion, Epiphone wins hand down. The Strat types don't look much better in my opinion, again, sharp fret ends and awful looking headstock and logo. If you see any of their relic jobs, you'll notice that they range from passable from a distance to hideous from any range.
Imagine a rich, authentic acoustic guitar tone coming from your electric guitar - at the flick of the switch! Replace your current saddles with Graph Tech's ghost modular pickups and one of our Acousti-Phonic preamp and you'll have instant access to true, acoustic tone from your electric guitar or bass, without altering your electric pickups. With the ghost Acousti-Phonic system you can play one guitar! It can be electric AND acoustic, separately, or blended together for an infinite range of new and exciting sounds.
Alan Parsons: "I always use condenser mics on a guitar amp, never dynamics — they're too telephoney. That's an unfair expression for a very good dynamic mic, but by comparison to a condenser, you're not going to get the bottom end." While this stance is more hard-line than that of most engineers, condenser mics are, of course, regularly used for recording electric guitars. However, in practice they rarely seem to be used on their own and are very often lined up alongside the trusty SM57.
Every guitar player needs a great acoustic guitar – or several – in their collection. Finding the right acoustic guitar for you can be a daunting process even for the most seasoned player. If you are new to shopping for guitars, then it is even more critical that you learn all you can before you make your first purchase. If your first acoustic guitar is not the appropriate choice for you, then it can dramatically reduce the enjoyment you will get out of your instrument. If you are a new guitar player, the wrong guitar can be downright discouraging. You want a guitar that fits you, is effortless to play, and has the rich, beautiful tone you love to make it the instrument you dream of playing hour after hour.
The body is pre-drilled and crafted from basswood, while the maple neck is meant to be glued into the neck joint, something that requires a bit of care and precision. Because of its hollow body design, installing electronics can be a bit of a challenge, but very doable as attested to by reviews. Note that wood is raw and unfinished, so you'll need a bit more sanding and patching before you paint on it.
Unless it's broken and will need to be replaced, start with obtaining a new nut that is anything to your liking, preferably a blank nut rather than a pre-cut to avoid improper string height. If cutting a blank try copying your old nut and make adjustments if needed using the neck as a guide after cutting out the nut. To do this take a sharp blade that is easy to work with such as an X-acto and cut the finish that holds the sides of the nut. Make sure to cut all of the finish as it will break apart when you take out the nut.
Nice-4-Bass-V1.5 This is an sf2 simplified version of three different basses - all with 4 velocity layers. It includes the 1958 Otto Rubner double bass played and mapped by Drogomir Smolken, recorded by Ludwik Zamenhof. The samples are exceptional and some percussive effects have been mapped to some high notes. Royalty-free for all commercial and non-commercial use. Copyright 2016 Karoryfer Lecolds (Karoryfer Samples). The original Meatbass sfz version for Sforzando has round-robin sampling and includes arco as well as pizzicato presets. (http://www.karoryfer.com/karoryfer-samples).
Coming from the back of its introduction in 2006, this Hellraiser series of Schecter’s electric guitar is proving to be a game changer in the strumming market, by excelling far ahead in areas like sight, sound, durability, quality, and affordability—a stark definition of a unique electric guitar. These set of Hellraiser guitar are not only beautiful but also versatile.
Most delay pedals have controls for the number of repeats (called “feedback”), the volume of the repeats and the time between each repeat. Some pedals have what’s called “tap tempo”, where you can tap your foot on the pedal and the delay unit will match the speed of the effect to your foot, allowing you to match the delay time to the tempo of a song. Delay pedals are often used to thicken up heavy lead guitar sounds, or to subtly add more to a simple rhythm guitar part.
The previous drawing illustrates the electrical and magnetic function of a single-coil pickup. Some pickups might use six permanent magnets in place of the six pole pieces to create the magnetic field, but the idea is the same: create a steady magnetic field around a coil in proximity to the guitar string. The name "single-coil" pickup becomes more significant when compared to the humbucker or "dual-coil" pickup.
By 1939, Supros had grown again. The ’38 line was essentially intact with the addition of a number of new resonator acoustics. New was the No. 23 Supro Arcadia Guitar, a sunburst birch-bodied resonator made by Harmony. This had a simple nickel coverplate with two concentric circles of round holes, a slightly-rounded head with an oval Supro metal logo plate. The fingerboard had four dot inlays, the body two f-holes. Cost was $22.50.
Speaking of, you’ll probably look to upgrade either the bridge or the tuners at some point, because heavy whammy use will pretty quickly throw this out of tune. If you don’t use a whammy often, this makes a very fine choice, indeed. The neck is satin finished for better feel. All in all, a very worthwhile guitar that comes in at less than half the price of most of the other options on this list.
There’s a huge range of cheap electric guitars out there that would not look out of place on the stages of the world thanks to high quality manufacturing and the brands actually caring about their products – “cheap” does not always mean poor quality and plenty of guitars out there will give you a fantastic playing experience for many years without breaking the bank.
If the book had been proofread better, I'd give it 5 stars. For example, there are places where the text has both a fret number and standard musical notation, and the fret number is wrong. The book refers you to play along with the instructional CD backing tracks, but it doesn't tell you which track number to play. It's easy enough to figure out what was meant, but a little more care would have been better.
Do you have an old guitar that requires knowing how to repair a damaged guitar body? Read on and learn some neat tricks for repairing body damage on a guitar. Body damage on a guitar ruins the acoustics. Body damage on a guitar body really make it useless in the playing arena. If you are looking to bust out that old guitar but need some handy advice on how to repair some old damage, MadeMan has the fixes for you. This article will give you the fixes for larger damage and the annoying little nicks and teach you the way to repair them.
Description: Body: Mahogany - Neck Attachment: Set - Neck Wood: Mahogany - Fingerboard: Rosewood - Binding: Cream - Frets: 22, Medium - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tone Pros - Hardware: Chrome, 2x Volume Control, 2x Tone Control, 3-Way Switch, Grover Tuners - Pickups: Duncan Designed - String Instrument Finish: Vintage White, Vintage Gold Top, Black
Much like booster pedals – where its placement depends on what exactly you’re looking to boost – the location of compressors and wah-wah pedals in a signal chain will vary depending on what type of sound you are trying to create. In this case, you are encouraged to experiment with their order and see what you like best. Although as mentioned above, try to keep the wah-wah after tier one effects as they generally do not sound that usable in that order. Compressors, on the other hand, can be placed before any pedal, even distortion, as it shapes the signal rather than modifies it.
So leaving aside the complexities of exactly emulating acoustic instruments with speaker technology -- which we have all come to accept although no speaker can sound quite as sweet as (or at least not exactly like) the acoustical nuance of a fine wooden stringed instrument, we reach the vast majority of modern music - amplified sounds. Again, stringed instruments are among the most difficult to emulate, if not the most difficult to emulate technologically, because of the vast and infinitely variable set performance possibilities which in turn produce a vast and infinitely variable set of physical reactions. Even if MIDI notation can document the coordinated left-hand/right-hand performance of various pitches, velocities, durations and legato, our VST is strained to faithfully reproduce every possible physical result of every possible combination of performed licks.
I got this one because my 18-year-old Takamine G-series has some serious fret wear, and a slightly warped neck, even with the truss rod maxed out, and will cost more to repair/refurbish than this one cost outright. Hence, the action is quite high, and it's hard to play bar chords higher than the 3rd fret, and there's some noticeable buzz and rattle unless I hold my mouth just right...
Adherence to the Past While acknowledging the impossibility of scientifically proving tone, many guitar players will still argue vehemently for a classic Les Paul crunch, or they’ll get ready to throw down if you claim solid-state amps sound better than valve amplifiers. They will concede the point intellectually, but on a more deeply rooted, emotional level, they can’t get beyond their own perspectives. It’s almost like observing fire-walkers at the circus. Your brain may understand how the technique works and how it can be safe. But your heart and nerves won’t let you take the chance of barbecuing your feet.
A functionally solid-body electric guitar was designed and built in 1940 by Les Paul from an Epiphone acoustic archtop. His "log guitar" (so called because it consisted of a simple 4x4 wood post with a neck attached to it and homemade pickups and hardware, with two detachable Epiphone hollow-body halves attached to the sides for appearance only) shares nothing in design or hardware with the solid-body Gibson Les Paul introduced in 1952. However, the feedback associated with hollow-bodied electric guitars was understood long before Paul's "log" was created in 1940; Gage Brewer's Ro-Pat-In of 1932 had a top so heavily reinforced that it essentially functioned as a solid-body instrument. In 1945, Richard D. Bourgerie made an electric guitar pickup and amplifier for professional guitar player George Barnes. Bourgerie worked through World War II at Howard Radio Company, making electronic equipment for the American military. Barnes showed the result to Les Paul, who then arranged for Bourgerie to have one made for him.
This is a really cool program. It let's you fiddle with a lot of cool effects, without having to spend a lot of money. The program works really well, after a bit of fiddling with the Jack server, and it far exceeds some of the commercial programs I have tried. I hope that this project gets some attention :) If I wasn't a "coding dyslexic", I'd be the first to sign up.
The Eastcoast Vintage T Series Custom Electric Guitar seen here in Flame Red is a cheap electric guitar that certainly doesn’t suck! It features appointments usually associated with higher tier guitars such as a solid alder body and hard maple neck. In addition, you have a high quality 22 fret rosewood fingerboard as well as 2 x single coil pickups to achieve a wide variety of tones from rock to blues to country – this thing can handle it all. The “T” style bridge is a great feature often found on guitars 3 x the price. A fantastic option and an extremely hard working, handmade guitar for those in need of a high quality first guitar or a great second option for the studio or stage.
Modifying this guitar is also quite easy and you can add things to it to make it a lot better. Overall, it is just the right value for your money item to have. Again, if you are an intermediate or expert level player then avoid this guitar. If you are a beginner & looking for the lowest price electric guitar for beginners clicks the button on this one. With the price you pay, I am pretty sure you will be impressed by the performance of this guitar. Here is the link to buy this product or know more about it –
The auditorium style is a standard mid-sized acoustic guitar, with a lower bout that is generally the same width as a dreadnought, but with a smaller waist. Sometimes referred to as an "orchestra" body, these guitars balance volume, tone, and comfort, and have been regaining popular ground in recent decades. In 1992, Eric Clapton used an acoustic guitar of this body size, when he appeared on MTV Live to record his Unplugged album.
For 10" speakers, the most common combo amp and speaker cabinet configurations are 2x10" and 4x10". For speaker cabinets, 2x10" and 4x10" are the most widely used, although 8x10" cabinets are used in stadium concerts, especially in louder rock genres. Other configurations with 10" speakers do exist, but they are less common. For example, there are a small number of 1x10" and 3x10" combo amps and speaker cabinets, and a small number of 6x10" cabinets. Bass speakers are usually made with stiff paper cones. Hartke combo amps and speaker cabinets are unique in that the cone is made from paper, except for the middle, which is made of aluminium. Gallien-Krueger's MB210-II combo amp uses ceramic speakers.
I think Matts’ advice is good, (old guitar strings can be helpfull for “fishing”) but if you change your p’ups and switching often an accessible control cavity is a great thing, just be sure to drop all pots and such into the body and drill through the potentiometer holes so you know where to place template and assure router bit won’t hit anything dangling in the body.
The Science of Electric Guitars and Guitar Electronics considers the electric guitar and related accessories from a scientific point of view. The majority of books about electric guitars try to avoid using mathematics when describing the scientific phenomena related to the electric guitar. However, mathematics is an invaluable tool in the design processes of all areas of technology, even when designing musical instruments and audio electronics. This book presents simple mathematical methods for modelling the electric guitar as a signal source for electric circuits such as effect pedals and amplifiers. In addition to modelling the electronics inside the electric guitar, the principles of operation of some vintage guitar effects and amplifier circuits are explained and analysed using systematic methods of circuit analysis. The book is intended for everyone who is interested in the design and analysis of basic analogue electronics used in the electric guitar and guitar-related accessories. The presented topics cover the whole signal chain from the guitar strings to the loudspeaker. Therefore, a solid foundation is established for creating own designs in guitar electronics using basic components of analogue electronics.
As can be seen from our reviews above, it clear that the best guitars are those that meet the needs of the player—whether beginner or intermediate player—the best electric guitar should be able to provide quality sound, last for a considerable time, easy to play and always reliable when needed. Although every single guitar listed here are of top quality, there are different guitar for every budget, style and genre of play.
Description: Body: Mahogany - Body Construction: Solid - Top Wood: Ash - Neck Attachment: Set - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Rosewood - Inlay: Pearl - Dot - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 6 In-Line - Bridge: Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Black - Pickups: Ibanez - String Instrument Finish: Natural Blue
While the bulk of new players will likely want an amplifier for their electric guitars, acoustic-driven music is still plenty popular amongst players of all skills. And while acoustics are fairly loud on their own, some players still want to pump up the volume from time to time, as well as shape their sound. And you can do all that without sacrificing the warmth of your guitar’s sound with the Behringer Ultracoustic AT108. Perfect for home practices and coffee shop performances, this amp was specifically designed to enhance the volume and tones of an acoustic guitar (or, more accurately, an acoustic-electric). It also has a secondary microphone input to amplify your voice alongside your guitar.
Being a PODHD user for many years now, I am but one of the many who commend its balance of versatility and sound quality. Like many reviewers, it allows me to gig and record conveniently, often times plugging straight to PA with great results. I've also seen a number of professionals using PODHD500X's in their concerts, so it's not surprising that even experts at Music Radar were convinced, saying: "The modelling is excellent throughout, with authentic-sounding amps and quality effects".
I have a Hohner DC. It is either a MIC or MIK. It does not have body, or neck bindings, but in every other respect is very nice. It was one of the first guitars I got when I started paly about 5 years ago. As a matter of fact, I had not played it for over a year - I recently got it out of the case, re-strung it and played it regularly for a couple weeks. I have been going over my colection looking for things I could sell off, but I decided to keep this one.
An octave generator is a simplified form of pitch shifting. This effect will allow you to add an octave—usually below—the fundamental note. Units that add a lower octave exclusively are referred to as sub-octave generators. They can add a lot of depth to the guitarist’s sound. Many bass players also use sub-octave generators to significantly fatten up their sound.
Tonhöhe ebenfalls gehoben und kann auf die gewünschte Tonlage eingestellt werden. Der Ibanez DOWNSHIFTER erlaubt es, die Tonlage einer Saite durch einfache Hebelbetätigung auf eine vorgegebene gewünschte Position zu senken. Um präzises Tuning für sowohl Auf- und Ab-Positionen zu erzielen, müssen Sie beide Hebeleinstellungen vor Betätigung des Downshifters voreinstellen.
The Teisco brand name stands for 'Tokyo Electric Instrument and Sound Company'. Teisco was founded in 1946 by renowned Hawaiian and Spanish guitarist Atswo Kaneko, and electrical engineer Doryu Matsuda. Teisco guitars sold in the United States were badged "Teisco Del Rey" beginning in 1964. Teisco guitars were also imported in the U.S. under several brand names including Silvertone, Jedson, Kent, Kingston, Kimberly, Tulio, Heit Deluxe and World Teisco. While guitars manufactured by Teisco were ubiquitous in their day, they are now very collectable.
Initially inspired by his older brother Jimmie, Stevie picked up the guitar at an early age and was playing in bands by the time he was 12. By the time he formed his legendary trio Double Trouble in 1980, Stevie Ray Vaughan was already a legend in his adopted hometown of Austin, Texas. After hearing and seeing Vaughan playing at Switzerland’s Montreux Jazz Festival, pop icon David Bowie invited Stevie to play on his Let’s Dance album. Vaughan’s career took off form there.
If the fuzz is the grandaddy, the Arbiter/England Fuzz Face (introduced 1966) is the grand-poobah of the grandaddies’ social club. A handful of other fuzzes came first, but this distinctive round, smiling box is the one most guitarists point to when identifying the fuzz tone of the gods. Why? Two words: Jimi Hendrix. Apparently he died and took it up there with him. Oh, and two other words: germanium transistors. When these fuzz fans point to the Fuzz Face, however, they don’t point to just any Fuzz Face. They point to a good one. The quality of these pedals varies wildly, mainly because the tolerances of germanium transistors themselves varies wildly and sorting out the good ones was more work than the makers could afford to put in (or, perhaps, knew was necessary). Contemporary makers from Fulltone to Z.Vex to Mayer take the time and trouble to laboriously sort their germanium transistors, and it pays in spades in terms of tone and consistency.
Fuzz boxes and other heavy distortions can produce unwanted dissonances when playing chords. To get around this, guitar players (and keyboard players) using these effects may restrict their playing to single notes and simple "power chords" (root, fifth, and octave). Indeed, with the most extreme fuzz pedals, players may choose to play mostly single notes, because the fuzz can make even single notes sound very thick and heavy. Heavy distortion also tends to limit the player's control of dynamics (loudness and softness) - similar to the limitations imposed on a Hammond organ player (Hammond organ does not produce louder or softer sounds depending on how hard or soft the performer plays the keys; however, the performer can still control the volume with drawbars and the expression pedal). Heavy metal music has evolved around these restrictions, using complex rhythms and timing for expression and excitement. Lighter distortions and overdrives can be used with triadic chords and seventh chords; as well, lighter overdrive allows more control of dynamics.
Now imagine the puddle again, but this time imagine some wood blocks (12 inch long 2x4's for those of you with rusty imaginations) that are placed on their sides in the puddle in the shape of a three-sided box with the open side facing the pebble's point of impact. The radiating lines go in to the box and bounce back or reflect off the walls. Soon, there are so many lines radiating around in that imaginary box that they all collide with each other and become a random, jumbled mess. Eventually, the size of the lines and the number of them diminish. That my friends is reverb.
Just SOLD #2 another fine example of the vintage 1960s era J200 copy by the great luthiers at Alvarez in the mid 1970s - the 80's WoW very well done impressive... Alvarez from over 40 years ago. This example is JVG rated at very good + 8.6/10 vintage condition with beautiful patina and character mojo as well so cool Gotta love this Beauty! This instrument has received our JVGuitars "set up" and several upgrades as well we have installed a new set of Martin 80/20 bronze Marquis strings for a crisp tone with great bass and volume as well as a Martin solid natural bone nut & a compensated saddle set custom fit into its original fully functional adjustable bridge with plenty of room for up or down adjustments to your personal taste further upgrades do include throwing out the old plastic tone robbing bridge pins for the superior resonation of solid ebony wood with brass ring and beautiful abalone inlay bridge pins and this was for tonal reasons and it looks much more high end as well, then we removed the old economy tuners of the era ( a weak point ) and installed a set of Grover tuners old holes were touched up in the process looks good and works excellent now to keep this guitar in tune and as a side benefit the added girth at headstock increases sustain as well. The medium slim profile C shaped neck is 1-11/16ths at the nut and also is pretty much the same as the 60's Gibby profile the frets are the originals as well and still playing well without buzz as per JVG set up. Truss rod is working fine and the headstock is looking cool with its Old School script Alvarez mother of pearl logo and crown design with its patina and cool old Alvarez Truss rod cove this guitar is striking as well. Great sounding like a Piano wow and she's playing with ease with excellent string action now. She retains her excellent vintage Sunburst and finish still shines nicely of course she is not new or mint it has some natural finish checking several that only adds to its Mojo along with several doinks here and there on the body and top a few that caught edge near binding on front and back not so big rather small and small paint had chipped off and so I addressed them with a fine tip matching color lacquer tip pen to touch up and to help preserve original finish integrity and looks much better as well. We also installed a replacement pickguard and it fits perfectly and looks great too. The 1960's VIBE and this instruments playability makes this an excellent choice for that SWEET Jumbo tone well crafted over 40 years ago Vintage Script Logo on headstock inlayed in mother of pearl on correct law suit era open book Gibby style headstock. Made in Japan well taken care of all these years and ready for you to enjoy another 40. Overall she is SWEET! Contact Joe to buy: email@example.com.
The tricky little lead lines with which she peppers St. Vincent’s already impressively broad catalog hint at Annie Clark’s almost casual mastery, but her true genius lies in the way she treats the guitar as a dynamic sound source rather than a static instrument. In her hands, and within a tautly complex compositional framework, the guitar sounds limitless, capable of screaming, squalling, soaring, and crying — as if Hendrix were sitting in with a downtown art-rock band.
by pedalhaven This little board from @andshamlian is so sick! Don't forget to DM/Tag us to submit your photos! ▪️ ▪️ ▪️ ▪️ ▪️ #pedalhaven #pedalboard #guitarpedals #knowyourtone #ambienttones #pedalboards #pedalnerds #pedalporn #guitar #gearporn #gearnerds #pedalboardpeople #shoegaze #geartalk #guitarsdaily #gottone #tonefordays #guitargear #reverb #gearpost #boardshot
If you’re looking for a decent guitar at a super affordable price, look no further. This Ibanez features Powersound Pickups as well as 5-way switching to give you a variety of tones and styles. With a contoured body, it’s super easy to get comfortable while shredding away on this puppy. If your music styles fall in line with hard rock or country, then this is the guitar for you!
Once you have the essential elements in place-a great amp, guitar, and guitarist-you almost can't help but get a great guitar tone. Crank the amp up to the appropriate level and begin with some mic comparisons. It's especially telling to audition different types of mics: for example, dynamics, ribbons, and large-diaphragm condensers. (I rarely use small-diaphragm condensers for miking guitar amps; on the other hand, I've found that almost any microphone will strike gold once you find the right spot for it.)
Supro guitars were first produced in the 1930s by the National Dobro Corporation (rebranding as Valco in the 1940s), with the first solid body electrics produced in the early 1950s. The company produced guitars with numerous names on the headstock, with Supro and National being the best known. They produced some interesting guitars in the 1960s, including some of the earliest fiberglas-bodied instruments; financial pressure necessitated a merger with Kay of Chicago in 1967, but the new comapany only managed to limp on until 1968, before folding and ending all guitar production.
Juszkiewicz, 64, is known for being temperamental, ultracompetitive and difficult to work for. A former Gibson staffer recalls a company retreat in Las Vegas punctuated by a trip to a shooting range, where executives shot up a Fender Stratocaster. In recent years, Juszkiewicz has made two major pushes, both seemingly aimed at expanding a company when a product itself — the guitar — has shown a limited ability to grow its market.
Bring up the topic of electrics, and Martin is hardly the first name of recall. The term “electrics” is not meant to include the company’s many fine acoustic-electric guitars, many sporting top-notch electronics (which ultimately remain acoustic beasts), but rather electric guitars meant for country chicken pickin’ or raunchy rock and roll. However, beginning in the early ’60s, Martin has launched periodic forays into the electric guitar marketplace with some very interesting, if commercially unsuccessful, results (which explains why the Martin name doesn’t come immediately to mind). Most coverage of the Martin brand is focused, quite rightly, on their substantial acoustic achievements. For this essay, however, let’s take an alternative view and look at the company’s various electric guitars, its thinline hollowbodies and later solidbodies.
Nearly all Martin instruments come in different styles. The higher the style number, the more fancy (and collectible) the instrument. Again starting in October 1930, Martin stamped all flat top guitars with the style number, directly after the body size (and above the serial number). Style numbers can range from 15 to 45. A letter can follow the style number too, giving some additional info about the instrument. For example, a "T" after the style number indicates a Tenor guitar. See the general specs section for a full list of these suffixes.
Reverbs and delays can sound particularly unruly when run into an amp set dirty. If you use natural amp distortion but still like using pedals, you can run some effects into the front of your amp, and run time-based effects into an effects loop (most modern amps with channel switching will have an effects loop). Some modern programmable pedals, such as the TC Nova System or Eventide Time Factor delay, allow you to switch between -10 and +4 operation, so you can use them in front of your amp at the instrument level or at line level in an amp effects loop. This is really handy, allowing you to create and store presets tailored for using the pedal either in front of the amp or in the loop. Of course you can also use studio-type rack effects in amp effects loops. Units such as the Fractal Audio Axe FX and TC Electronic G-Major work great in this configuration, allowing you to store many presets and get pristine time-based effects, whether you are using clean sounds or dirty sounds.
The matching Baton amplifier had the same cabinet shape as the Supreme, but was smaller, with a brown simulated alligator covering, and a square grill with rounded corners. It had three tubes, four watts of power, and a 61/2″ speaker. Similarly, it’s possible that the Baton amp may have debuted by 1940. In April, 1942, the Baton Guitar Outfit cost $57.50.
Rickenbacker continued to specialize in steel guitars well into the 1950s, but with the rock and roll boom they shifted towards producing standard guitars, both acoustic and electric. In 1956, Rickenbacker introduced two instruments with the “neck through body” construction that was to become a standard feature of many of the company’s products, including the Combo 400 guitar, the model 4000 bass, and, later, the 600 series.
Before I get started, one quick note of caution. Because you need to play 'through' Cubase in order to hear the effects, you'll need a low-latency system — which means a fast computer, and a good audio interface, with quality ASIO or Core Audio drivers. Even if an interface has a 'zero‑latency' monitoring feature, that won't do you any good, as it will simply route the input signal to the output, without going through Cubase or any of its plug‑ins, which kind of defeats the purpose… Preferably, you should also have an interface with a high‑impedance input (suitable for guitar and bass). Many modern interfaces have an 'instrument input' which will do the job, but if not, you'll need to use a guitar‑friendly preamp, compressor, or similarly 'neutral' effect to feed a line input (or use a DI box).
I just built this kit, which I ordered directly from Mod DIY. Its the first pedal kit that I have built, although I do have a fair amount of electronics experience. Overall, I was impressed with the kit. All the parts were included, and functioned just fine. The instructions were outstanding, particularly if you use the high-res picture of the inside of a finished model for reference. There was ONE step omitted in the direction, which was to solder a short wire between terminal 3 of the toggle switch to connection 12 on the junction rail. But that was easy to spot.
Two of the strongest reasons to buy an acoustic guitar are user-friendliness and price. Some musical instruments are prohibitively expensive for beginners, and they’re difficult to learn, too. Not the acoustic guitar. Acoustic guitars are easy to learn, easy to carry, easy on the ears. And you can buy an acoustic guitar for an affordable price. The most difficult challenge in purchasing an acoustic guitar is finding the ideal fit for you. In this shopping guide, we will discuss some important elements to consider when browsing the acoustic guitar market.
Description: Body: Maple - Flamed - Body Construction: Semi-Hollow (Chambered) - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Block - # of Strings: 6 - Scale Length: 25.5" (65cm) - Headstock: 3+3 - Bridge: Tune-O-Matic - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Chrome, Diecast, 2x Volume Control, 2x Tone Control, 3-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - String Instrument Finish: Amber, Red
This string overview is useful for understanding what choice to make that suits your play style the best. As players, we are always searching for the highest possible functionality, while balancing tone and playability for the genre we play. Check out what brand and gauge your guitar heroes use to help you zero in on your perfect string set and keep on rocking!
Learning to do your own setup is just as important as learning how to play. If you feel uncomfortable doing it, go to a pawn shop and spend that 50 bucks you would have spent on a setup and buy a hack bass instead and pratcice on that. You can also practice your soldering and anything else without fear of ruining it and end up saving a ton of money in the long run!
Here we have a sweetie from the late 1970s folks they just don' make them like this anymore this is the RARE High End Lawsuit 5053 model this model was discontinued decades ago. This guitar was made nearing 40 years ago of woods said to have been aged 20-30 years at time of its being built.... food for thought. Fresh release from the JVGuitars Vintage Vault is a beauty seldom seen in this configuration and in this condition we have collected many 5053 Alvarez lawsuit era guitars not all are like this one is SPECIAL this is a must see and hear beauty! Based on the Martin top of the line D-45 this Japanese crafted D-45 copy was crafted with top workmanship only the top luthiers were allowed to use this precious expensive aged Brazilian Jacaranda rosewood on this guitar its back - sides - fingerboard - bridge and headstock are ALL made of this exotic tone wood, the neck looks to be a high grade Honduran Mahogany and proudly still displays it's original imported by Saint Lewis Music gold Medallion and fancy SLM truss rod cover see pics The top is Solid Sitka spruce this guitar is detailed and adorned with much perfling and inlay top to bottom including its fingerboard and headstock, this example is in top playing condition and cosmetically excellent as well and is VERY RARE in deed to find one so excellent. The neck is a nice handful like the old Martin a medium slim profile, its beautiful fingerboard is excellent as are its frets.... Headstock is striking with its A over A inlay in mother of pearl, tuners are original and still doing an excellent job, This guitar has the tone only the Exotic wood series guitars can produce unique rich and dynamic with excellent volume and clarity a fingerpickers delight. Just freshly received a JVG setup with a new Martin Bone & compensated sadle along with a fret dress and a new set of Martin 80/20 Phosphorius Bronze strings 12's x 54 for a substantial tonal upgrade from its old plastic. Overall rated 9.0 +++/10 well preserved it is over 40++ years old and has been lovingly played and well taken care of all these years is not new or mint of course it clearly is well above average used / vintage This comes with a good hard shell case ... and will protect it for the next 4-5 decades. Wonderful players guitar in excellent vintage condition when will I ever see another like this??? its here as of today ask if serious about owning this gem Thank you for your interest in our vintage guitar contact Joe to buy this guitar at: JVGuitars@gmail.com Pics soon to come.
6) PLEASE DO NOT POST THE FOLLOWING: Memes, jokes/skits, rage comics, sub-related rant posts, spam, advertising of your goods or services, shill advertising, links to outside retailers (links in discussions are ok), gear for sale posts (head to /r/Gear4Sale). Comment manipulation (edits made to conceal behavior) is strictly prohibited. Market research is strictly prohibited.
1. Blackstar ID:15 TVP ($229): This is one of the best combo amps on the market and with good reason: it comes with a variety of options to not only get you playing in no time. It also allows you to record very easily with a built-in USB option. You can select from six different power responses modeled after popular tube amp sounds (via Blackstar’s True Valve Power system) and even when turned down, the amp doesn’t lose its bite. The built-in multi-effects allow you to experiment with the world of effects and the Insider Software allows you to edit up to 128 user storable patches to further your sonic crafting.
Leo Fender's work is timeless. This is easily deduced by simply looking at the popularity of both Stratocasters and Telecasters. With that said, Strats are arguably the favorite between the two. A top of the line American-made Stratocaster still costs a bit more than what our budget here is, however, there is an alternative. Fender's plant in Mexico builds great Stratocasters that aren't really behind their American counterparts. You essentially get a near identical performance at a more affordable price due to the stigma. The Fender Classic Series '70s Stratocaster is one such guitar.
Interesting site.I searched make before break and you appeared.Ive just bought a Squier Classic Vibe Butterscotch telecaster and it has stock Alnico 5 pups. It got me remembering how, back in the 1960s I used a standard U.S. Tele and did the jamming in between thing. If you were careful it balanced and held in place.I always loved that position. I think, if I remember correctly, you could get between bridge and both and also neck and both.I think it was a superior sound to any 5 way switch I’ve heard. Is it possible to modify my make after break classic vibe switch to make before break or do I need a new switch? And can you buy make before break switches for a 2 pup Tele ? Thanks much.Mike.U.K.
Epiphone makes some great guitars for beginners, and they get the top spot on my list. Epiphone is owned by Gibson, one of the biggest names in the guitar world. As a subsidiary, Epiphone is allowed to make budget versions of classic Gibson guitars. This means newbies have a shot at starting out on a legendary Gibson design such as the Les Paul or SG.
The instruction covers both electric and acoustic guitars. The music part is thorough but progresses pretty quickly. It covers a few genres so that you can get the specific information you want whether you’re playing the blues or going classical. The best thing about it is that it is an all-in-one reference that even experienced players will appreciate.
Rule 1 - There is a logical order for groups of effects. Some effects remove or add certain amount of frequencies, some change the basic shape of the audio waveform, and others react to the shape and amplitude of the waveform. Those are three main types of effects that logically can't come in any other order than they were just listed, or you end up with amateur results. The reason for that becomes clear in the next rules.
Unfortunately, there is no single unified format used for Ibanez serial numbers. Ibanez guitar production is outsourced to several companies and facilities through the world and the numbering schemes are different in each region and/or factory. The information on this page is culled from several sources both on-line and off-line and represents a distillation of the available information. It applies primarily to electric guitars, but some information may also be applicable to acoustics.
Phrase sampler: Like a loop pedal, a phrase sampler will store loops or phrases of even greater length. The more expensive and sophisticated phrase samplers will save multiple phrases or loops, drum and bass, rhythm guitar, or practice solos. Some have USB connectivity and can hook up to your computer for uploading, so you never lose a loop or phrase.
When Charlie Christian got on the bandstand with Benny Goodman in 1939, he single-handedly propelled the electric guitar into the mainstream. Though he wasn’t the first guitarist to plug in and play electrified, Christian’s performances as a soloist on Goodman tracks like “Flying Home” and “Honeysuckle Rose” document the first instances that the electric guitar was used effectively as a lead instrument in a Big Band setting.
The solid-body electric guitar is made of solid wood, without functionally resonating air spaces. The first solid-body Spanish standard guitar was offered by Vivi-Tone no later than 1934. This model featured a guitar-shaped body of a single sheet of plywood affixed to a wood frame. Another early, substantially solid Spanish electric guitar, called the Electro Spanish, was marketed by the Rickenbacker guitar company in 1935 and made of Bakelite. By 1936, the Slingerland company introduced a wooden solid-body electric model, the Slingerland Songster 401 (and a lap steel counterpart, the Songster 400).