Many bass players believe that tube amplifiers produce a "warmer" or more "natural" sound than solid state amplifiers when lightly or moderately driven, and more pleasing distortion characteristics when overdriven. Some performers also believe that tube amps have a greater level of perceived loudness for a given amount of amplifier power. Even though tube amplifiers produce more heat than solid state amplifiers, few manufacturers of tube amplifiers include cooling fans in the amplifiers' chassis. Usually adequate cooling is provided by passive convection. Adequate airflow is needed to prevent excessive heat from shortening the tubes' lifespan or producing tonal inconsistencies.[13] Tube amplifiers require more maintenance than solid state transistor amplifiers, such as replacing vacuum tubes or rectifying the tubes.

There's no wrong answer to which neck will work best for you. When people speak of rounder vs. flatter being better for chording/bending, they are referring to the radius of the fretboard, not necessarily overall neck shape. The fretboard on all guitars has a curvature across is, from the the treble to the bass side. Generally speaking, most people would agree that rounder fretboards facilitate better chording, while flatter ones facilitate better bending, but even that's not hard and fast.
The tuner goes first. This one is pretty easy. It doesn’t want to hear an effected signal; it wants to see the direct input from the guitar. Another reason for putting the tuner first is that if you’re using any true-bypass pedals, the TU-3 will give them a buffered signal, which will protect your tone from loss of signal in the cables when other pedals are off. This is another one of the reasons there as so many TU tuners in pedalboards worldwide, even ones using nothing else but boutique true-bypass stompers.
It is a standard dreadnought with 26 frets. There are no electronics, no cutaway, and no fancy upgrades. It has a book matched sitka spruce top, rosewood fingerboard, adjustable rosewood bridge, cream colored plastic binding, rosewood back and sides, and a black inlaid headstock. The neck is not one piece and is made from presumably African mahogany. It has closed gold tone tuners, black beveled pick guard and some plain black line art for a rosette. This guitar is void of polyurethane and has a lacquer finish, so much the better.
The first design was an Early Telecaster model, called Squier, with a single mic. The main contribution Leo Fender did, was the bode and neck removal separetly. In previous models, when the guitar need repairs, the complete instrument needed to be sent, while, after Leo fender design, the plate could be unscrew and sent to the shop only the damaged part.
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions- opens in a new window or tab ... Read moreabout the condition

I also was amazed how well my Norma FG-7 played..its a parlor size acoustic guitar made of what looks to be all mohagony with a white pic guard kinda cool looking but it was a cheap guitar for the times.it was made in Korea...I acquired it in a small trade ...the bridge was broken on the peghead and luckily both pieces were still there as it still had 4 strings that looked original to me that held the two pieces together...lol....I re-glued the bridge...cleaned her up real well...re-strung her...and wow...I couldn't really contain myself as she sounded as well as a lot of other guitars out there today...although they aren't worth that much...it;s all in how they play and sound...so I believe they are a dandy for sure...but most will be a rebuild! have fun all and keep strummin'


4) Aside from enough publishing errors that, to my sensibilities, mean that the book is not ready to be published, instructions are shown on how to add a Varistor switch to a guitar, and a Les Paul is used for the example. The drilled hole given as the example is nothing less than a hack job, I hate to say it, but it is. I would faint if I saw a tech do that to my guitar. Besides its being really bad advice in the first place, if you are going to do it, DONT follow this example!
Phase Shifter pedals found their way into the guitar community in the 70’s with pedals like the MXR Phase 90, Mutron Phase Shifter, EH Small Stone, Foxx and others. The sweeping sound it produces is unmistakable and a legendary trademark of many guitarists sound. The MXR Phase 90 can be heard all over Van Halen 1 and II. Brian May used the Foxx phase on “Sheer Heart Attack,” The Eagles “Life In The Fast Lane”, and Led Zeppelin’s “The Rover” to name but a few.
Many community, vocational or technical colleges offer technical and musical programs for those who wish to become guitar technicians. Many are instrument construction and/or repair programs. Guitar tech courses include construction, set-up, structural repair, fretwork, structural design and finishing for acoustic and electric guitars. Any courses involving musical theory and music technology may be helpful in advancing a guitar tech's career.
As Tom Wheeler writes in The Soul of Tone: Celebrating 60 Years of Fender Amps, "It’s powerful, it’s loud and it’s sensitive to the player’s touch. It sounds great, responding beautifully across the frequency spectrum. It exhibits a sparkling, harmonically rich tone at low and moderate volumes. At louder volumes it thickens with a sweet distortion that only seems to get creamier the more it’s cranked. It is particularly well matched to certain popular guitars, especially the Stratocaster."

Beside learning the basics, avoiding modeling amps and multi-effect pedals in the beginning will allow you to focus on the few basic effects every guitarist needs along the way – Reverb, Chorus, Delay and Compressor. Reverb is a must, and most amps have onboard reverb effects. Once you begin to get the hang of playing guitar and wrap your head around those basic effects you can branch out to other effects and modeling amps.


Also still in the line in ’66 were our old friends, the MJ series. These were essentially unchanged except for a new striped metal guard, the new hooked headstock, and a new chrome-covered oval pickup with an oval indentation stamped in the center and six flat, round poles. Available were the MJ-3L (Teisco Del Rey ET-300), MJ-2L (promoted in Japan, but not the U.S.) and MJ-1 (Teisco Del Rey ET-120). The MJ-1 had a new on/off rocker switch and a second rocker for solo/rhythm. Promoted in Japan, but not the U.S., was the little BS-101 bass, pretty much unchanged from before.
All of us got carried away. We had great guitars back in the ’50s and ’60s. Then we went a little crazy. All of us – players and makers alike – started adding features and making demands that drove complexity up, up and away. Silvertone guitars represent the honest character of the guitars that created the classic music that still rules today. ... more ...

Recording? The best amps for recording WON'T be big, 100-watts Marshalls, for instance! On the contrary, small amps are the best choice. We're talking about small valve amps, here. That's because, unlike with bigger, louder amps, you can crank up small valve amps, pushing them to tone heaven. If you did the same with bigger amps, it wouldn't work - you'd sound so loud you wouldn't be able to make a good recording! This technique has been used by many, many top artists. Despite using big & loud marshall amps onstage, Jimmy Page used a small Supro valve amp on the early Led Zeppelin albums. Likewise, the Arctic Monkeys used an old Fender Champ on most of their debut album.
Arch top body size is equivalent to the flat top 000 body size, 15" wide across the top, carved spruce top, back is not carved but is arched by bracing, rosewood back and sides, 5-ply top binding with pearloid outer layer, elevated tortoise pickguard with b/w binding, backstripe of two horizontal lines surrounded by two rows of diag lines (like a Style 45), bound ebony fingferboard, style 45 fingerboard snowflake inlays, trapeze tail piece, vertical "Martin" peghead logo, bound peghead, gold plated parts, sunburst top finish.
I Have a '70 lyle hummingbird and its a solid spruce top and mohagony neck back and sides. My guitar luthier fully inspected it. Mine is in near mint condition and sounds identical to the '64 Gibson Hummingbird my luthier has. He was trully freaked out by this.. ha ha He keeps trying to buy it from me but im affraid im hanging on to mine. It seems there is alot of contradictory information on these guitars. It is super hard to get more than a small paragraph of info on these things. One site out there has several catalogs from lyle guitars but they require a payment or paid membership to view them. If you are interested google lyle guitar catalogs. There is one that sold for 600.00 at joes vintage guitars.com Its Identical to mine. If I find any more info Ill post as discovered.

I've been to Steve about a dozen times with my guitars, families and friends instruments and have sent several people there and have nothing but great things to say. He is reasonably priced and likely one of the most talented and experienced Luthier's in Boston. It's rare to see any establishment get 5 stars from so many people and Steve deserves it! Only thing is, if you're in a rush to get your instrument back, go somewhere else where they do it quickly and without much thought/TLC. Steve takes his time to do it right and has a lot of customers because he's the guy to go to in the greater Boston area. Highly recommend!
Pickups are complex devices. No matter what we do, we cannot model them with spot-on accuracy. They do have a series resistance (R6), but the L1 and C3 inductor and capacitance, respectively, but these are not real circuit components, but are a simple model placeholder for the complicated interactions that appear due to Maxwell’s equations, when we have a wire wound around magnets (see below image):
Slicer – A dynamic effect that sounds like your guitar tone is chopping in and out. This percussive effect is akin to sequencer-type effects used by synthesizers. The effect turns the volume of the signal on and off, and sounds like the signal is being “chopped up” or “sliced” in a specified pattern. The BOSS SL-20 Slicer features 50 patterns to turn your guitar into a groove machine!
The first trick is the most obvious one: to double a crunch or heavily distorted guitar with a clean one. By sub-mixing a clean sound, you will be able to retain some precision, which is no minor detail considering that distortion has the annoying tendency of blurring sound. For this trick to be as transparent as possible, the crunch and clean performances must be as similar as can be. That being said, if you have a hard time getting that perfection, you can always "cheat": be it by editing the clean sound to make it match the original performance or simply doing some reamping with the first take, as discussed previously. In both cases the trick ought to work wonders because the clean take is only meant to be "felt" but not distinctively heard by the listener.
{"eVar4":"shop: amplifiers and effects","pageName":"[gc] shop: amplifiers and effects","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop18":"skucondition|0||historicalgrossprofit|1||hasimage|1||creationdate|1","prop2":"[gc] shop: amplifiers and effects","prop1":"[gc] shop: amplifiers and effects","prop17":"sort by","evar51":"default: united states","prop10":"category","prop11":"amplifiers & effects","prop5":"[gc] shop: amplifiers and effects","prop6":"[gc] shop: amplifiers and effects","prop3":"[gc] shop: amplifiers and effects","prop4":"[gc] shop: amplifiers and effects","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
It has a solid poplar body with a maple neck and rosewood fingerboard, and based on the early reviews of the Epiphone Les Paul SL, the fit, finish and general playability are all pretty good. It’s loaded up with Epiphone’s reliable tune-o-matic bridge, a volume and tone knob, as well as a three-way selector switch to toggle your pickups and dial in tone. The hardware does feel admittedly cheap, but the general consensus is that this guitar ships well-made, well-setup and more than appropriate for a first-time player.
Electric guitars were originally designed by acoustic guitar makers and instrument manufacturers. Some of the earliest electric guitars adapted hollow-bodied acoustic instruments and used tungsten pickups. The first electrically amplified guitar was designed in 1931 by George Beauchamp, the general manager of the National Guitar Corporation, with Paul Barth, who was vice president.[3] The maple body prototype for the one-piece cast aluminium "frying pan" was built by Harry Watson, factory superintendent of the National Guitar Corporation.[3] Commercial production began in late summer of 1932 by the Ro-Pat-In Corporation (Electro-Patent-Instrument Company), in Los Angeles,[4][5] a partnership of Beauchamp, Adolph Rickenbacker (originally Rickenbacher), and Paul Barth.[6] In 1934, the company was renamed the Rickenbacker Electro Stringed Instrument Company. In that year Beauchamp applied for a United States patent for an Electrical Stringed Musical Instrument and the patent was later issued in 1937.[7][8][9][10]

Cool guitar! You really don’t see many of these anymore. You are correct that it’s similar to the Washburn Wing series, specifically the Washburn Eagle from the late ’70s and early ’80s. In fact, aside from different fretboard inlays and brand names on the headstocks, when you compare the two they’re nearly identical. If this connection seems odd, the occurrence of very similar guitars with different brand names is more common that many of us would think.
Yamaha electric guitar is very durable.  However, some of its parts can be damaged by normal wear and tear.  One of the most common parts that can be easily damaged is the output jack.  The output jack of Yamaha guitar is frequently used.  Cables are being plugged into it.  After playing a tune, you will definitely unplug the cable so you can keep the guitar in its case.

In order to achieve supreme neck grip comfort, the fretboard edge is finished with a smooth curve that extends from the border between the fretboard and the neck, and then to the surface of the fretboard. The detailed neck shape is precisely carved using a ball mill for ultimate consistency. The width measurements of the fretboard are at 42mm at the nut and 56.4mm at the last fret. These dimensions allow for an easy grip in the lower register, and a more modern feel in the higher register.
Bass guitars (like guitars) in many ways are like cars. Their appearance is a major factor in your buying decision. But also like cars, especially for the first-time buyer, there are far more important factors to know about in order to ensure you buy a bass guitar that is both properly playable and that stays in tune, enabling you to make progress with it. 
As you know, like most guitars sporting more than a single pickup, your Strat lets you select any pickup by itself or choose certain dual-pickup combinations. The standard way to connect multiple pickups is to wire them in parallel. This generates the classic tone our ears know from countless records, when a guitarist uses the bridge and middle or middle and neck pickups in tandem (positions 2 and 4 on a normal 5-way Strat switch).
When Levon Helm of The Band sang "I pulled into Nazareth, was feelin' about half past dead" in "The Weight," he wasn’t alluding to a weary pilgrim’s desire for salvation. Rather, he was singing about a mythological trip to Nazareth, Pennsylvania, home of C. F. Martin & Co., makers of Martin flat top acoustic guitars. Founded in 1833 by a German immigrant named Christian Friedrich Martin, whose father was also an instrument maker, Martin...Continue Reading

Paul Simon, the great wordsmith, speaks as vividly through his guitar as his lyrics. Weaned on early doo-wop and rock & roll, Simon got caught up in the folk revival during the mid-Sixties, traveling to England to study the acoustic mastery of Bert Jansch. He has continued absorbing new influences, as on "Dazzling Blue," off his most recent album, So Beautiful or So What: "All that folk fingerpicking is what I did with Simon and Garfunkel, but [here] it's on top of this rhythm with Indian musicians playing in 12/8." At 70, he's as nimble as ever.

You're close, but not quite where you want to be with your tone.  You are officially a serious tone chaser; you've already swapped the stock burstbuckers in your awesome R9 Les Paul for something better ... but you are still only at 95-percent of the TONE you want, need, and hear in your head.  Keep seeking grasshopper, and you will find.  For only those who persist will drink from the holy grail.
Beside learning the basics, avoiding modeling amps and multi-effect pedals in the beginning will allow you to focus on the few basic effects every guitarist needs along the way – Reverb, Chorus, Delay and Compressor. Reverb is a must, and most amps have onboard reverb effects. Once you begin to get the hang of playing guitar and wrap your head around those basic effects you can branch out to other effects and modeling amps.
Quality-wise, they range from complete and utter crap, to OMG! Acoustics, tend to fall into the former range. Electrics, mostly the hollow bodies, were somewhat, but not always better. Solid bodies, mostly made from plywood, BUT they do have their own feel and sound. I happen to love them, others despise that cheap feel and sound. Remember, they were built to fill the growing demand of guitars, that the kids saw on tv, with the Monkee's and the Beatles
Guitar chords and signatures. Find and save list of chords. Basic guitar chords A sheet of the most used rock chords. Suitable for beginners. Empty chord sheet An empty sheet of chords templates to print out and use. Basic guitar chords Em, C, G, D, Am, E, and A Free lesson on the basic guitar chords Em, C, G, D, Am, E, and A. The following chords are 7 of the most basic open position chords. An open position chord is one that contains at least o
In Cleveland power trio the James Gang, Joe Walsh combined Who-style fury with Yardbirds-style technical fireworks and R&B crunch, notably on 1970's "Funk #49." The humor in Walsh's bluesy facility came out in the talk-box flight on his '73 solo hit "Rocky Mountain Way." But it was when he joined the Eagles in 1975 that he truly lodged himself on classic-rock radio. Walsh brought a hard-rock edge to the Eagles' easygoing pop songs, creating a series of indestructible licks in the process: See his staccato-snarl riff in "Life in the Fast Lane" and his elegant aggression in the dueling-guitars section of "Hotel California." Walsh influenced the Who's 1971 classic, Who's Next, although he didn't play a note on it: He gave Pete Townshend, as a gift, the 1959 Gretsch Chet Atkins guitar that Townshend played all over that album. Townshend later repaid the favor while talking to Rolling Stone in 1975: "Joe Walsh is a fluid and intelligent player. There're not many like that around."
Great playing and sounding bass. The Ibanez BTB series in a 'very playable' 4-string version. Huge tone is delivered via 2 active pickups that feature controls for volume, bass, midrange, treble and balance. We believe the pickups are actually made by Bartolini. 'Locking' 1/4 jack. Solid wood, natural finish body. Rosewood fingerboard on maple neck. Tuning is accomplished via quality, 'sealed' tuning machines. Rock solid and stays in tune. Set up great! Currently has 'nylon wound' strings for a softer 'jazz' tone. Frets show virtually no wear. Body finish has VERY little wear. Includes gig bag.
Slot Peghead vs. Solid Peghead (steel string models): Most models converted from a 12 fret slot peghead to a 14 fret solid peghead around 1934 (except the OM series, which went 14 fret in 1929/1930 and the style 17 and 18 models which were available in 14 fret style in 1932). Basically if the guitar has a 14 fret neck, it will have a solid peghead. If it has a 12 fret neck, it will have a slot peghead. Note there were some post-WW2 gut string and classical models (i.e. 0-16NY) and some post-WW2 special order steel string guitars (i.e. 1967-1993 D-18S) which always have a slotted peghead.
Either way, the results in the Descent Reverb are nothing short of phenomenal.  If you watch the demo video below, you'll hear some of the most unique sounds capable of being produced by a guitar pedal. Pigtronix did something similar with delay and pitch shifting in the Echolution 2 Ultra Pro, but we think the combination is even better in the Descent.
I know this is one of those questions where there's not any one single correct answer, but I'm curious what neck relief specs others are using for their SG? I've read enough articles on the web to acknowledge that there's clearly no consensus, as there probably shouldn't be, considering different playing style, string gauge selection, etc. Yet I still would be interest what others find useful as a starting point. Recognizing that neck relief is just one step (the first) during set-up. According to one useful article that I read (http://mysite.verizo...guitarsetup.htm), when the question was put to Gibson, their response was:
Ease of Use: Multi-effects pedals are inherently more complicated to use than individual stompboxes. As such, we value multi-fx units that are not overly complicated, and require hours with the user manual to understand. Look for pedals with intuitive layouts and interfaces. Technology has come a long way, and most multi-effects pedals have good quality sound. To us, ease of use is a huge selling point (probably the most important behind price), and can differentiate the good from the great.
Thanks, guys....well, I don't think I'll be able to play any Agiles but I'll try and get my hands on some Epi's and give them a whirl. How are the stock pickups on both? Definitely in need of a swap? I had an Epi Les Paul an eon ago and don't recall liking the stock pickups, but I was also in highschool then and knew nothing about tone. Also, a quick look at Ebay indicates that any Epi SG in a color other than black or cherry will be hard to come by...
The Line 6 Spider IV is the most fully featured beginner amps out there, yet is surprisingly inexpensive, only edging out the Orange Crush PiX CR12L a little bit on cost. The Line 6 Spider IV 15 offers four amp models, six built in effects, a built in tuner, a headphone jack, and a CD/MP3 player input. Everything a beginner needs to practice in one compact package. These features aren’t completely necessary for beginners to have, but they do serve as a nice convenience and the Spider IV does not cost that much more in the process to add them. On top of that, the Spider IV still manages to be straight forward and easy to use, despite all the built in options.
Do these sites harm the artists, or do they spread the understanding of music? Do they generate more sales of music, or reduce it? Do they provide education and stimulate participation by young people in the creation of music? Do they remove the incentive for artists and publishers to faithfully reproduce official versions of TAB, lyrics, or music notation or do they encourage people to seek official versions when they find the unauthorized versions lack the detail or accuracy they demand?
Besides insulting Taylor Swift in a way even Katy Perry would bristle at (“Nobody would confuse the pop star’s chops with Bonnie Raitt’s. But she does play a guitar.”), Edgers manages to make it through an entire history of the electric-guitar industry as it stands without quoting more than one female guitar player — the Runaways’s guitarist Lita Ford. Any person who has actually interrogated the music landscape deeper than, say, an Eric Clapton record would recognize that the electric guitar isn’t dying. The throngs of women who play electric guitar just don’t get exalted or celebrated in the same way as aging men. But there are legions of women playing guitar — maybe Edgers just hasn’t been paying attention.
The headstock is located on the end of the neck opposite the guitar body. It is fitted with tuning keys, also known as tuners, tuning pegs, or machine heads. These adjust the tension of each string, changing their pitches. The nut is a small strip located where the headstock meets the neck, that is grooved to guide the strings onto the fretboard. On an acoustic guitar, the nut is commonly made of plastic, but it can also be bone, graphite, or any number of other materials.

Upgrading the components in your guitar’s control cavity should give you significant improvements in tone and component life. If your guitar has single-coil pickups, buy 250K pots. If it’s packing ’buckers, go for the 500K jobs. If your ax has humbuckers and single-coils, I recommend 500K pots. This could make your single-coils sound a bit brighter than normal, but it will unlock your humbuckers’ full potential. For this job you’ll also need a soldering iron, solder, safety goggles, wire cutters, and a camera, to help you keep track of your original wiring connections (your cellphone will work just fine for this).
Description: Body Construction: Solid - Neck Wood: Maple - Neck Construction: 1 Piece - Fingerboard: Maple - Frets: 21 - Inlay: Dot - # of Strings: 6 - Headstock: 6 In-Line - Bridge: Fixed - Cutaway: Double - Hardware: Brass, Chrome, 1x Volume Control, 1x Tone Control, 5-Way Switch - Pickups: Humbucker - Pickup Configuration: H-H - Guitar Features: Pickguard - String Instrument Finish: Traditional Violin
The heaviest heffalumps in this year’s roundup, share a few strands of DNA with early Mastodon, blending bludgeon and benign  in ambitious and unpredictable ways. Brady Deeprose and Dan Nightingale form the two-pronged guitar attack, leading these lofty compositions from blast-beaten brutality to doom-y sludge and back again. Their debut album Mire was released last month and is the sort of fully-formed statement that requires metallers to pack a spare pair of pants.
Combining Reverbs: You don't have to generate all of the reverb sound from a single plug-in, and using two different reverbs can also help you to save CPU power. For example, though a nice convolution reverb gives a good, believable sound, long impulse responses tend to eat up CPU. By using the convolution reverb for the early reflections, and then using something like Logic 's Platinumverb or Waves Trueverb to add the reverb tail — which is less critical to our perception of the sound — you should get a convincing but less processor-intensive result. Matt Houghton

There are only two Amazon reviews for this instrument, as it is at a higher price point than other guitars, but the reviews are very positive. The rich tone of the cedar as well as the ability to take this classical guitar into the world of electrical pickups makes this a fabulous option for the musician looking to upgrade to a more professional-sounding instrument.
“Spectrum ‘5’ has an unusually thin neck. To achieve the proper rigidity in this fast action neck Teisco had to select the hardest (and the costliest) material available…Ebony. The adjustable neck is fashioned out of 5 plys [sic] of laminated Ebony to insure maximum strength. The fingerboard of the Spectrum ‘5’ is likewise fashioned out of Ebony. Note the unique position markers and the extra wide, easy to finger frets.
Original plate reverbs were mechanical in nature. There was a literal plate inside the amplifier, which would transform input signal into vibration. Then you would have a pickup located somewhere near the plate, that recorded those vibrations. Today, such a contraption comes across as relatively crude, but many still love the unique mechanical sound it produces. Spring reverb uses a pretty much exact same principle, only this time you have a spring in there instead of a plate. The biggest improvement a spring reverb offers is reduction in both weight and size of the device.
Some resonator guitars possess metal bodies and these are called steel guitars. This can lead to some confusion with the Hawaiian guitar of the same name. They are two distinct instruments. The Hawaiian steel guitar takes its name from the steel bar used to create the glissandi and the Resonator steel guitar refers to the material used for the construction of the body.

The solution is pretty simple actually. When setting your intonation it should look like two sets of steps. You should never need to move the saddles all the way forward or turn them around. If you want to adjust something do it in a way that allows you to keep this configuration. You do that and you'll never have to worry about tuning issues period, let alone a g-string.
On round hole martin guitars, the serial and model numbers are stamped on the neck block inside the instrument. The number can be seen by looking inside the sound hole. Look at an angle towards the neck. All f-hole Martin archtops have their serial and model numbers stamped on the inside center of the backstripe, roughly under the shadow of the bridge (and best seen from the bass side "f" hole).
Just ask any savvy stompbox builder or low-tuned 7-string player: Sometimes the best way to add power to your low tones is to remove a bit of bass. That’s because the lowest frequencies in your signal disproportionately overdrive your amp and effects. Siphoning off just a bit of bass can add clarity and focus. At extreme settings, the filtering can produce sharp, squawking tones akin to those of a ’60s treble booster pedal (not a bad thing). If you’ve ever grappled with high-gain tones that make your amp fart out, here’s your flatulence remedy.
One of modern metal's key figures, Dimebag Darrell founded Pantera with his brother, drummer Vinnie Paul Abbott – forging a style that combined brutally precise, punk-honed grooves with splatter-paint melodic runs. After he was tragically shot by a deranged fan during a show with his band Damageplan in 2004 – on the anniversary of John Lennon's death, freakishly enough – the tributes rolled in from fans, peers and forerunners. "One of the greatest musicians to grace our world," Black Sabbath's Geezer Butler said simply. "Rest in peace."
Of course, the effect is not as good as using a professional studio but most users report that reproduction is very good for a simple computer application. The interface of Guitar Rig is extremely well laid out and even for those new to amps and guitar effects, it doesn't take long to navigate your way around. If you intend to use Guitar Rig for live performances, a convenient Live View displays the most essential readouts and level monitors to keep your eye on.
This is Yamaha’s C40II classical guitar, an inexpensive nylon-strung guitar that’s a cut above some of Yamaha’s even cheaper models designed for schools and the like. Many companies offer a line of low-priced, very basic designs tailored for education facilities. Don’t go that far down the price pecking order. The C40II for $140 USD on Amazon is a good compromise. Please do yourself a favor and get the $13.58 two-year protection plan!
A Vibe or Univibe pedal reproduces the sound of a rotating speaker by synchronizing volume oscillation, frequency-specific volume oscillation, vibrato (pitch wavering), phase shifting, and chorusing in relation to a non-rotating speaker. The modulation speed can be ramped up or down, with separate speeds for the bass and treble frequencies, to simulate the sound of a rotating bass speaker and a rotating horn. This effect is simultaneously a volume-oriented effect, an equalization-oriented effect, and a time-based effect. Furthermore, this effect is typically related to chorus. Some vibe pedals also include an overdrive effect, which allows the performer to add "tube"-style distortion. This effect is the most closely related to a rotary speaker. Some Vibe-only pedals include:

Support your local music shops! The Guitar Store is a great spot in a convenient location. Helpful and friendly staff all around. A good assortment of electric and acoustic guitars, amps, and more pedals than you could possibly imagine. No cases full of BOSS Metal Zones either - we're talking real pedals for the pedal enthusiast. They also are great for lessons/workshops and instrument repair. We had been bugging the guitarist in my band for having a noisy output jack for weeks. He took his guitar in, came in during a slow time, and they replaced the jack for him on the spot! Amazing! So while Guitar Center might be your only option to buy that fancy pack of tapered-B 5-String bass strings, The Guitar Store should be your first choice for literally anything else. Check it out! SUPPORT LOCAL MUSIC SHOPS! But they make you leave your backpack at the counter?!? ZERO STARS!!!!! ;-)


Chorus is useful for 'softening' rhythm guitar or synth pad sounds, but it does tend to push sounds further back into the mix, so it should be used with care. Adding more brightness to the sound can help compensate for this effect. Chorus also works well on fretless bass, but tends to sound quite unnatural on vocals. Phasing can be used in a similar way to chorus but, whereas chorus creates the impression of two slightly detuned instruments playing the same part, phasing sounds more like a single sound source being filtered, where the frequencies being 'notched out' vary as the LFO sweeps through its cycle.
We all know the sound of this effect: It replicates varying degrees of the sound of playing your guitar in the gym showers, a cathedral, or Mammoth Cave, and it has proved itself one of the most atmospheric aural adulterations available. Since none of those locations is entirely gig friendly, however, our ever-handy techs have bottled the flavor in a reliable, portable form. This category covers both echo and reverb effects, since they are versions of the same thing. The term “echo” was used more often in the early days, and is sometimes used today to refer to the distinct and distant repeats of a signal, while “delay” refers to anything from the same, to the short repeats heard as reverb, to the complex, long, manipulated repeats of an intricate digital delay line. Either way, they are both really the same thing, just used differently.
This electric guitar style has experienced surges and lulls in its popularity, but has never fallen off the scene, due to the number of great players who have chosen to use the Flying V, such as Jimi Hendrix, Dave Mustaine, Kirk Hammett and Michael Schenker.  The Flying V offered many of the same benefits as the SG with a much more distinctive body shape.  It is now a very common guitar among heavy rock and metal guitarists and will achieve its destiny of being a guitar of the future!
Fender guitars are generally equipped with single coil pickups, resulting in a brighter tone compared to humbucker pickups, for instance. This is part of Fender’s charm, and contributes to the characteristic tone of their instruments. Single coils are designed to cut through the mix with their bright sound, but a drawback is that this can cause issues with humming (1).
• Heavy is as Heavy Does: For low hanging alternate tunings like open D or dropped D, consider a heavy string gauge – at least .11s, although Stevie Ray Vaughan, who kept his instrument turned down just a half-step, employed a set gauged .13 to .58. Thicker strings will maintain their tension better when they’re low-tuned, which makes for less fret noise and other undesirable distortion. Many players feel thicker strings make for better slide playing, too, since the strings resist going slack under the pressure of the slide. But that’s really a matter of feel and learning to control a slide more than a string thing.
I Have a '70 lyle hummingbird and its a solid spruce top and mohagony neck back and sides. My guitar luthier fully inspected it. Mine is in near mint condition and sounds identical to the '64 Gibson Hummingbird my luthier has. He was trully freaked out by this.. ha ha He keeps trying to buy it from me but im affraid im hanging on to mine. It seems there is alot of contradictory information on these guitars. It is super hard to get more than a small paragraph of info on these things. One site out there has several catalogs from lyle guitars but they require a payment or paid membership to view them. If you are interested google lyle guitar catalogs. There is one that sold for 600.00 at joes vintage guitars.com Its Identical to mine. If I find any more info Ill post as discovered.
The benefits of owning a combo amp and one or more powered speakers is that a bassist can bring just the combo amp to recording sessions or small venue gigs, but bring the combo amp and the additional powered speaker(s) to large venue shows to add more stage volume. Another benefit of having a combo amp and additional powered speakers is that the bassist could leave the additional powered speakers in the rehearsal space (or, if playing as a house band for a club, on the venue's stage), and only carry the combo amp back and forth from her home to rehearsals or shows, saving time and energy.
the switch is to change pickups and the knobs are for volume and tone. u only need to mess with them if u want to change the sound of the guitar for various songs or styles of music. to tune the guitar u use the tuning pegs on the headstock (at the end of the neck). u need to tune it if it gets out of tune and make sure u replace the strings fairly often especially if u get a nice guitar like a les paul. old strings get tighter and can pull the neck and make it bow forward making it harder to push the strings down to the frets.
Later, on-board electronics allowed guitarists to move about the stage, rather than stay immediately in front of a microphone. On-board electronic tuning, availability, uniformity, and frugal costs facilitated performances by guitar ensembles like Robert Fripp‘s Guitar Craft students. Ovation has also produced solid-body electric guitars and active basses.
The guitar player who makes his guitar sound anything but a guitar. Helicopter rudders, disc scratching, and his use of the kill switch for staccato like guitar riffs has made him probably the most innovative guitar player of our time. He is a guitarist who can take feedback, and ground hum from his own body into coherent music. Be it Rage Against The Machine, or Audioslave you can always see Morello’s signature licks shining through.
I have owned a Mesa Boogie Dual Rectifier for 5 years now and couldn't be happier! Granted, the amp took a long time to dial in my perfect tone, but it was a good way to familiarize yourself with the amp. If you want cleans, crunch, distortion, and a wall of gain that is big enough to destory small islands than this is the perfect amp. Not to mention, the customer service is out of this world! About a month after purchasing the amp Mesa Boogie called to make sure everything was okay and I was enjoying the amp. They also ask you to take a questionnaire on how the sales person performed. Great company, Best amps.

To cut to the chase, we can say that a changing magnetic field generates or "induces" electricity. It's also true that a changing electric field generates magnetism. If you feed electricity through a coil of wire, you generate a magnetic field around it. That's how you can make a magnet controlled by electricity—better known as an electromagnet. Electricity and magnetism are really two different aspects of a single phenomenon: electromagnetism.
It’s interesting to note that luthier Steve Klein introduced a guitar that got a lot of press in the early ’80s with a body virtually identical to the Ovation Breadwinner. According to Charles’ son (and future president of Kaman Corporation), Bill Kaman, Jr., Ovation considered “pointing this out” (i.e., legal action), but given its bad track record with solidbodies, figured it wasn’t worth the effort.
Across the United States, there are increasing concerns from businesses about the supply of science, technology, engineering, and mathematics trained workers. Although science and math test scores in the US are among the lowest around the world, the US educational system is in the process of revitalizing the “hands on” learning techniques as a way to enhance the participation and success of students. Our project meets the needs of applied learning with the flexibility of being modular in the classroom.
Categories: Gibson Guitar CorporationBanjo manufacturing companiesBass guitar manufacturing companiesGuitar amplifier manufacturersAmerican companies established in 1902Manufacturing companies established in 19021902 establishments in MichiganCompanies based in Kalamazoo, MichiganManufacturing companies based in Michigan1902 in musicCompanies that filed for Chapter 11 bankruptcy in 2018
Maybe the pickups that came with your guitar are just cheap and not up to your standards. At that point, an upgrade might be less of a stylistic issue and would done for the purpose of improving the overall sound quality of your instrument. In most cases, upgrading the pickups on your guitar are the single most effective way to improve the overall tone and sound quality.
The version of the instrument that is best known today is the solid body electric guitar. Rickenbacher, later spelled Rickenbacker, did, however, offer a cast aluminum electric steel guitar, nicknamed The Frying Pan or The Pancake Guitar, beginning in 1931. This guitar is reported to have sounded quite modern. Audiovox built and may have offered an electric solid-body as early as the mid-1930s.
The lower strings of a guitar (E, A & D) will often have a nickel winding over their steel core. Nickel also makes an appearance in the frets of most guitars, which are commonly made from nickel-silver. Despite the name, this alloy doesn’t actually contain any silver, but is named for its silver appearance. It’s actually an alloy of copper, nickel, and zinc. These nickel-silver frets aren’t as hard-wearing as steel, so some guitar manufacturers use stainless steel instead to give the frets more longevity.
Maton was founded in 1946 as the Maton Musical Instruments Company by Bill May and his brother Reg. Reg was a wood machinist, and Bill a jazz musician, woodwork teacher andluthier who had for some years operated a custom guitar building and repair business under the name Maton Stringed Instruments and Repairs. The name “Maton” came from the words “May Tone” and is pronounced May Tonne.

After steel strings were the norm, rectangle bridges were still used on the lower end Martin models and smaller body models. Bridges don't last forever unfortunately, and the rectangle models are easy to reproduce. Hence here's some specs that may help you determine if a rectangle bridge is original. A Martin rectangle bridge should be 6" long and 1" (or slightly less) wide. The top of the bridge should have close to a 16" radius lengthwise. The tallest point of the bridge should be between the A & D strings, and the lowest at the high E string. The wing thickness is about .095".
While these sum up the most significant Gibson tone woods, other species do occasionally contribute to the brew. Swamp ash lends the Les Paul Studio Swamp Ash a degree of twangy sweetness and a round, slightly scooped midrange, while the most common Gibson fingerboard woods, rosewood and ebony, even make their mark on the frequency spectrum. Rosewood generally helps to add a certain thickness and creaminess to the tone—warming up the voice of a maple neck, or adding depth and cohesiveness to that of a mahogany neck—while an ebony fingerboard, long considered an upmarket option, contributes tightness, brightness, and a quick attack.
More and more are finding themselves downsizing their pedalboards, if not totally swapping all their stompboxes for a multi-effects unit. There are also many who are looking to upgrade their existing guitar processor. Whatever your case may be, it is our intention to help you find one that fits your needs, or at least point you to the right direction.

The Very Best Rock Vocalists All-Time Best Rock Frontmen Greatest Drummers Insane Rock Rumors That Are Actually True Druggiest Rock Stars of All Time What Their Kids Look Like Now Incredible Songwriters The Rockingest Women Singers Undeserving Members of the Rock HoF Great Guitar Rock Albums All-Time Best Rock Bassists Our Rock Hall of Fame Nominees Huge Stars Who Stepped Out of the Spotlight Old Rock Stars Who Still Look Pretty Good Rock Guitarists of the 1970s Rock Stars in Love Triangles The Greatest Living Rock Songwriters Mononymous Singers Greatest American Rock Bands Rumors That Were Never True
Not all stompboxes and rackmounted electronic devices designed for musicians are effects. Strobe tuner and regular electronic tuner pedals indicate whether a guitar string is too sharp or flat.[105] Stompbox-format tuner pedals route the electric signal for the instrument through the unit via a 1/4" patch cable. These pedal-style tuners usually have an output so that the signal can be plugged into a guitar amp to produce sound. Rackmount power conditioner devices deliver a voltage of the proper level and characteristics to enable equipment to function properly (e.g., by providing transient impulse protection). A rackmounted wireless receiver unit is used to enable a guitarist or bassist to move around on stage without being connected to a cable. A footswitch pedal such as the "A/B" pedal routes a guitar signal to an amplifier or enables a performer to switch between two guitars, or between two amplifiers.
He also opened the doors for left-handed guitar players by showing them that they too can master a musical instrument and make something unforgettable from it. In the same way that a “southpaw” boxer like Manny Pacquiao achieved unbelievable things in the ring, the gifted left-handed guitarist Jimmy Hendrix pushed guitar playing to its highest level.
Whether it costs $100 or $1000, the build quality should feel worthy of the money. Naturally with budget models you will find more laminated woods compared the solid woods and exotic materials used in expensive guitars. However, a good model will have laminates that are put together securely and cleanly, with no excess glue or rough spots. Even a good budget guitar will look and feel great.

Steve is the best. He made time for me to come in and talk about the problems I was having with my electric bass. When I got there, he knew exactly what was wrong with my bass, and he adjusted it quickly and perfectly. He also gave me a lot of incredibly useful information about what he was doing and why. I could not recommend Steve Morrill more highly.
Matsumoku is one of the Japanese manufacturers that did not survive long after the heyday of the 1970s guitar market despite having a long tradition of quality stringed instrument craftsmanship. Matsumoku produced guitars for major manufacturers Greco, Guyatone and Yamaha. Matsumoku made Arai, Aria, Aria Pro II and Aria Diamond badges, with Aria being their primary badge for a majority of this time frame. Badged guitars known to have been made by Matsumoku include Apollo, Arita, Barclay, Burny, Capri, Columbus, Conrad, Cortez (electrics only), Country, Cutler, Dia, Domino, Electra, Epiphone, Granada, Hi Lo, Howard, Ibanez, Lindberg, Lyle, Luxor, Maxitone (this guitar differs from Tama's Maxitone badge), Mayfair, Memphis, Montclair, Pan, Pearl (electrics only), Raven, Stewart, Tempo, Univox ,Vantage, Ventura, Vision, Volhox, Washburn (in 1979 and 1980), Westbury, Westminster and Westone. Possible Matsumoku badges include: Bruno, Crestwood, Conqueror, Eros, Mako, Memphis, Orlando and Toledo.
Of course, as guitar players we still want to remain open to a number of tonal aspects that happen after the front end of the initial attack. These elements aren’t necessarily in the front part of the very beginning of a guitar tone, nor are they delegated to the trail of lingering sustain. “The reason why people sound a certain way is because of little nuances, those little pull offs, those hammer ons, those plucking [dynamics]— the sequence of those things. Think of it as a sonic palette. That sequence is what makes the artist sound like himself.”

While electric bass players have used regular guitar amplifiers in large concerts since the 1960s, this is usually just for the higher register; a bass amp is still typically used for the low register, because regular guitar amps are only designed to go down to about 80 Hz. One of the reasons bassists split their signal into a bass amp and an electric guitar amp is because this arrangement enables them to overdrive the higher-register sound from the electric guitar amp, while retaining the deep bass tone from the bass amp. Naturally-produced overdrive on bass obtained by cranking a tube amplifier or solid-state preamplifier typically results in a loss of bass tone, because when pushed into overdrive, a note goes to the upper octave second harmonic.

Conceived in the early 1930s, the electric guitar became a necessity as jazz musicians sought to amplify their sound to be heard over loud big bands. When guitarists in big bands only had acoustic guitars, all they could do was play chords; they could not play solos because the acoustic guitar is not a loud instrument. Once guitarists switched from acoustic guitar to semi-acoustic guitar and began using guitar amplifiers, it made the guitar much easier to hear, which enabled guitarists to play guitar solos. Jazz guitar had an important influence on jazz in the beginning of the twentieth century. Although the earliest guitars used in jazz were acoustic and acoustic guitars are still sometimes used in jazz, most jazz guitarists since the 1940s have performed on an electrically amplified guitar or electric guitar.

A typical modern guitar tube amp has both a preamp stage and a master power amp output stage. The preamp section will be supplied with a set of smaller tubes (frequently 12AX7 or the lower-gain/lower noise 12AU7), and the power amp section has a set of large tubes (EL34, EL84, 6L6, etc.). The preamp controls input gain and typically provides treble, midrange and bass tone controls.
My husband was looking forward to checking this place out. When we entered a guy wearing glasses asked if he could help us with anything and my husband said "oh just browsing." So we walked around some more. When we got to the electric guitar section, my husband saw a $2,000+ guitar he wanted to try. He took off his jacket so as not to scratch the guitar and SLOWLY picked the guitar from the wall hanger. The same guy earlier suddenly came up to my husband and said "You can't just pull it out like that!" My husband was surprised and had to ask what he just said?! I was as surprised. The clerk said "You can't just take it unless you are buying it." Really?! My husband said then you should have told me earlier when we first came in. We did not see any signs nor there's any lock on the guitar hanger. Why would you buy without trying it first?! That clerk probably thinks my husband don't have the money. They just lost a customer and a bunch of my husband's musician friends.

Many of the modulation type effects pedals are made to approximate some aspect of the original rotating speaker.  That’s correct, you heard right.  The Leslie Cabinet was made as a companion to the Hammond B3 Organ and literally had a rotary speaker that could produce all of the common modulation effects depending on the speed setting.  Many companies now offer digital pedal versions that mimic the Leslie sound very well, so lugging around a huge speaker cabinet isn’t necessary, unless you are a purist or have a crew of roadies available.


{"pageName":"[mf] pdp: fender deluxe players stratocaster electric guitar","reportSuiteIds":"musiciansfriendprod","prop2":"[mf] shop: guitars: electric guitars","prop1":"[mf] shop: guitars","events":"event3,event50,prodView","evar51":"default: united states","prop5":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop6":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop3":"[mf] shop: guitars: electric guitars: solid body electric guitars","prop4":"[mf] shop: guitars: electric guitars: solid body electric guitars","products":";511597","linkInternalFilters":"javascript:,musiciansfriend.com","channel":"[mf] shop","prop7":"[mf] product detail page"}

{ "thumbImageID": "V70CE-Acoustic-Electric-Guitar-Transparent-Blue/519468000012000", "defaultDisplayName": "Ibanez V70CE Acoustic-Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Transparent Blue", "sku": "sku:site51274115042822", "price": "179.99", "regularPrice": "199.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Ibanez/V70CE-Acoustic-Electric-Guitar-Transparent-Blue-1274115042822.gc", "skuImageId": "V70CE-Acoustic-Electric-Guitar-Transparent-Blue/519468000012000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/V70CE-Acoustic-Electric-Guitar-Transparent-Blue/519468000012000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51274115042831", "price": "179.99", "regularPrice": "199.99", "msrpPrice": "299.99", "priceVisibility": "1", "skuUrl": "/Ibanez/V70CE-Acoustic-Electric-Guitar-Black-1274115042831.gc", "skuImageId": "V70CE-Acoustic-Electric-Guitar-Black/519468000001000", "brandName": "Ibanez", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/V70CE-Acoustic-Electric-Guitar-Black/519468000001000-00-60x60.jpg", "imgAlt": "" } ] }
This guitar is one of the more affordable left-handed variants that you will find on the market. With a 41-inch body and a full-scale, you won’t find any limitations to the music you wish to play. The body is 3 inches thick which not only makes it comfortable to hold but also play. The cutaway gives you good access to higher frets while also increasing the appeal of the guitar.
It should also be mentioned, that LX does not just stand for U.S. made. Originally LX was an indicator for an Ovation guitar that included several new features that were not available on previous guitar models. Back in 2007 Ovation explained on its website, that the new features included the new OP-Preamp, an advanced neck system (lightweight dual-action truss rod, carbon fibre stabilizers), a patented pick-up (made of 6 elements), inlaid epaulets, scalloped bracing as well as a new hard composite Lyrachord GS body.[25] Back then, no such thing as an AX model line existed (the first AX models appeared on the Ovation-website in 2010). Based on the website’s history the LX features must have been introduced in 2004.
With this new edition, they scrapped the DVD from the previous version, and introduced online video and audio clips, as a supplement to the book's teachings. They didn't take it overboard though, with just 85 videos and 95 audio tracks, but at least it's a step in the right direction. You can't learn music by just reading about it, you need audible tools.
For many engineers, a simple one-mic technique gives them all the recorded electric guitar sound they need. Dynamic types, such as the ubiquitous Shure SM57, are ideal for capturing loud sounds, as they can handle high SPLs. For a more accurate representation of the amplifier as the human ear hears it in the room, a condenser or ribbon mic can be employed, although care must be taken not to damage the mic with very loud signals. Pointing the mic at the centre of the speaker cone produces the brightest sound, with the sound becoming increasingly warm the further off-centre it’s placed. It’s common to position the mic quite close to the speaker grille, unless a degree of room sound is desired. A good starting point is to place the mic just off-centre, at a distance of between two and six inches.
The Wave's all tube design utilizes four dual triode vacuum tubes - three 12AX7s and one 12AT7 - and comes with a MOD® three-spring reverb tank. MOD® reverb tanks are deemed the closest to the original reverb tanks from the '60s made today. The Wave's reverb function can be switched in and out pop-free via the front panel toggle or with a footswitch. Footswitch sold separately (see P-H470 for compatible footswitch).

Instead of thinking about the different woods (mahogany, maple, rosewood, etc), all the different pickups, necks, scale lengths, bridges, body types… all you have to worry about is getting the STYLE right. 95% of the time, that will get you the SOUND you want as well. Of course, that being said, get the highest quality wood you can. For example, most players agree that a “solid sitka spruce top” is probably the highest quality wood you can get for a “beginner” level acoustic guitar, without compromising tone.
The key elements of mic positioning are distance from the source and orientation to it. Moving the mic closer to the amp provides more definition, increased highs and lows, and less room sound. As you pull the mic back, the sound becomes less detailed, more "midrangey," and more blended with the ambience. Depending on the room you're in, a distant-miked amp may gain a natural presence and unique character in the mix, despite an apparent decrease in definition. On the other hand, placing the mic too far back will result in a washed-out, murky, or hard-to-control tone.
The godfather of all that is sought after in rack gear; behold, the Soldano SLO Rackmount Amplifier. Those of you that have heard of the SLO (Super Lead Overdrive) already know that this thing can be brutal when it comes to lead tones. Possessing one of the tightest crunch and overdrive channels known to man, the SLO Rackmount is hailed as a grail piece of gear for many guitar players. The SLO-100 offers two channels, Normal and Overdrive, each with independent Preamp gain and Master Volume controls.  A footswitch is also provided for effortless noise-free switching between the two channels.  The Normal channel has a Bright switch and a Clean / Crunch gain selector switch.  Standard features include a tube-buffered effects loop and a slave output.  Bass, Middle, Treble, and Presence controls provide the tone shaping.  From Clapton to Van Halen, from Warren DeMartini to Lou Reed – and from you to Mike Soldano himself, the SLO is simply the player’s choice.
The D-120's all-mahogany body strays from conventional spruce top design, which results in a warmer and more articulate tone. This particular tone is ideal for guitarists who sing, and for those who accompany vocals, it also blends well with conventional spruce top acoustic guitars, easily cutting through the mix with its lower-mids emphasized voicing. And since the body is crafted from solid mahogany, you can be sure that the instrument grows with you, sounding better with age.
{"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: victoria","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"victoria","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"}
The goal is to find the body shape and configuration that appeals the most to your eyes and ears. The most straightforward choice for beginners will be the solidbody for its durability. Players who are looking to expand their sonic palette are usually the ones who will take interest in semi-hollow and hollow body guitars. For more information on this topic read The Different Types of Electric Guitars Explained.
On the other hand, if you do decide to stick with it, having a good guitar means you won't have to worry about upgrading in the foreseeable future when your skill levels rise above the problems associated with cheap options.  Realistically, no matter who you are or are buying for, you shouldn't get the cheapest option.  At least go middle-tier unless we're talking about a 5 or 6 year old's first guitar.

The following open-tunings use a minor third, and give a minor chord with open strings. To avoid the relatively cumbersome designation "open D minor", "open C minor", such tunings are sometimes called "cross-note tunings". The term also expresses the fact that, compared to Major chord open tunings, by fretting the lowered string at the first fret, it is possible to produce a major chord very easily.[14]
It would be great if we could be born with all our favorite music already memorized. But we're only human, so we don't get that luxury - if we want to know a song, we have to learn it! The process starts with reference materials, so don't wait to start building up a repertoire of your own favorites. Add the tablature to your collection and make sure to practice, and you'll be playing like your favorite guitar heroes soon enough.
  Korg SDD3000 Preamp Clone Great project! Since I finished it, it become one of my always on pedal! With a extremely subtle compression... Eclipse Device-2   DOPAMINE OVERDRIVE based on the Klon Centaur circuit. Materials: 01. Xicon 1% metal film resistors. 02. Kemet 5% MLCC (C0G) 03. WIMA Box Film... Refractor Black Octopus Pedalworx More build reports

This Blackstar combo amp might be really inexpensive (under $80) but it’s not a cheap model, quality-wise. Ideal for house practice, this baby has two channels (Clean, Overdrive) and is also fit for traveling. The compactness and durability of the model are great for people who want to travel with their instrument and equipment. If you are a beginner who has long given up on looking at the best amplifiers at $100, you need to know where to compromise on an amp. And Blackstar seems to do the best job as compromising on some aspects to still deliver a good sounding amp that is not too expensive. With 10-watts (there is also a 15-watt model available), you can practice for hours on end and produce pretty crisp, versatile tone. Is it the best amplifier I have ever tried? Definitely not, but it sure is one hell of a good competitor in its price range and an amazing guitar practice amp.
While a high school degree is not necessarily required, it does provide an edge for graduates who wish to become guitar technicians. Students should concentrate on classes such as music, band, English, shop class and mathematics. A major part of any education should include guitar lessons. Techs often need to be able to play by ear and must be able to pick up on any nuances in an instrument's sound and tuning.

Gibson 2012 SG Special '70s Tribute Electric Guitar, Left-Handed (with Gig Bag)   New from$649.00In Stockor 12 payments of $54.09 FREE 2-DAY SHIPPING Gibson 2017 SG Faded Electric Guitar, Left-Handed (with Gig Bag)   New from$659.00In Stockor 12 payments of $54.92 FREE 2-DAY SHIPPING Gibson 2017 Les Paul Standard Electric Guitar, Left Handed (with Case)   New from$2,299.00In Stockor 12 payments of $191.59 Free Ground Shipping Gibson 2019 LP Junior Tribute DC Electric Guitar, Left Handed, (with Gig Bag)   New from$799.00In Stockor 12 payments of $66.59 Free Ground Shipping See All Left-Handed Electric Guitars
The most defining feature has got to be the neck. It’s thicker than the standard Strat neck, which gives extra meat to work with when bending those strings. Even the fretboard was designed around this technique, with its narrow frets and flat fretboard. It’s not the cheapest one out there, but Fender Stevie Ray Vaughan Stratocaster is definitely one of the best Strats around.
So, how to use the tone knob? Open it to get a trebley sound, and roll it off to get a warmer, darker tone. Experiment. Some guitars sound best with the tiniest roll back on the tone knob, some songs require a certain combination of tone and pickup settings to sound best. Try to listen to the John Mayer DVD “Where the Light Is” and try to emulate the guitar tones there using only your pickup selector and knob. He uses different guitars and settings, but a lot of those can be emulated just with your guitar’s controls. Experiment.
For many people who pick up the guitar for the first time, learning scales is often not at the top of their priority list. This is normal and as a beginner guitarist, there is other more important foundation knowledge that should first be acquired. However, at the point when you start learning scales as a guitarist is when you know you’re starting to get serious about playing. Learning guitar scales is a fantastic way to practice your technique and theory. Scales also come in handy for a variety of purposes such as: Writing music Improvising/jamming with others Understanding how music
You're headed in the right direction - don't stop! yes, the keyboardist should control vibrato directly with the fingers, not automatically with an LFO. The more you rely on the technology to play the music for you, the worse your results will be in the long run. Is your intention to emulate a guitar, or to achieve a similar kind of lead expression and sound control during playing? Because these two are very different.
The XB-40, (short for Extreme bending-40 reeds), is unlike any other diatonic made. Released in 2003, it was specifically designed by harmonica specialist Rick Epping to simplify proficient bending of the notes. To make this possible, the XB-40 uses forty reeds as opposed to the usual twenty found in most ten-hole diatonics. With these bending capabilities, the XB-40 gives access to all the notes on the chromatic scale through bending the natural tones of each hole. This model was discontinued in 2013. Shortly before production officially ceased, Suzuki Music released a similar model the SUB-30.[28]

If you like to run all your effects into an amp set clean and get your gain sounds from pedals, you probably don’t ever need to consider using amplifier effects loops or a wet/dry/wet rig. If your amp(s) are set relatively clean, you will be able to use any of the effects listed above straight into the front of the amp—and they should sound really good.
I can't believe this! Blackstar are designed and built by retired Marshall professionals and they have every last bit of knowledge on tube amps, heads, and combos. I own a Blackstar HT-1R, it is 1w but it feels like 100w just the way the Blackstar team have combined their ideas and structures and balanced it out with tubes. And line 6 is further up the list? You are mistaken bro. Another thing. These are bloody expensive and aren't very well known but Two Rock make probably the GREATEST amps ever made and I would kill to fire one up!
This Blackstar combo amp might be really inexpensive (under $80) but it’s not a cheap model, quality-wise. Ideal for house practice, this baby has two channels (Clean, Overdrive) and is also fit for traveling. The compactness and durability of the model are great for people who want to travel with their instrument and equipment. If you are a beginner who has long given up on looking at the best amplifiers at $100, you need to know where to compromise on an amp. And Blackstar seems to do the best job as compromising on some aspects to still deliver a good sounding amp that is not too expensive. With 10-watts (there is also a 15-watt model available), you can practice for hours on end and produce pretty crisp, versatile tone. Is it the best amplifier I have ever tried? Definitely not, but it sure is one hell of a good competitor in its price range and an amazing guitar practice amp.
In fact, at the beginning of this article I mentioned John Mayer’s song, “I Don’t Trust Myself.” The way that guitar tone is achieved is by using a filter pedal called the AdrenaLinn III. That effect is a beat-synced filter effect, meaning it has the ability to sync up the sweeping filter with the rhythm of a song. This is accomplished by either tapping in the tempo on the pedal, or setting the tempo with the tempo knob.
There's just no getting around the Martin brand when there's talk about good acoustics. And since we're talking about the best of them, it's not surprising to find their name filling up multiple slots in this list. The Martin DRS2 acoustic guitar is special because it gives us a true all-solid wood body Martin acoustic guitar - at a very reasonable price point, in the dreadnought shape that the company themselves developed.
It’s 1951, a dark, rainy night on the backstreets of Memphis, Tennessee. Ike Turner and His Kings Of Rhythm are packing the gear into the station wagon, getting ready to head off to the studio to record a track for producer Sam Phillips, a track that the Rock and Roll Hall Of Fame will one day honor as the first rock and roll song of all time, ‘Rocket 88.’ (Although, distinctly unfairly, the song will be credited to singer Jackie Brenston and the imaginary band ‘His Delta Cats.’) “The amp—a Fender Bassman—was in the trunk of the car and it fell out, right on the road,” Ike Turner told Guitar Magazine’s Rick Batey in 1998, “and it was raining, so the amp got wet. When we got to the studio and plugged it in one of the tubes went ‘pop.’ We didn’t have no more tubes—so that’s where the fuzz came from.’

Harry Rosenbloom, founder of the (now-bankrupt) Medley Music of Bryn Mawr, Pennsylvania, was manufacturing handmade guitars under the name "Elger." By 1965 Rosenbloom had decided to stop manufacturing guitars and chose to become the exclusive North American distributor for Ibanez guitars. In September of 1972 Hoshino began a partnership with Elger Guitars to import guitars from Japan. In September of 1981, Elger was renamed "Hoshino U.S.A.", retaining the company headquarters in Bensalem, Pennsylvania as a distribution and quality-control center.
Home>Guitars, Amps, and Effects >Electric Guitars >Electric Guitars: 6-String PrintRefine your searchBy BrandCharvel (26)D'Angelico (28)Dean (32)Epiphone (65)Ernie Ball Music Man (30)ESP (67)EVH (7)Fender (141)Fret-King by Trev Wilkinson (3)Gibson (118)Godin (2)Gretsch (49)Guild (11)Hagstrom (9)Hamer (5)Ibanez (122)Jackson (54)Kramer Guitars (4)Line 6 (6)PRS Guitars: Paul Reed Smith (47)Reverend Guitars (9)Schecter (51)Squier (23)Steinberger (2)Sterling by Music Man (15)Supro (3)Taylor Guitars (6)Washburn (1)Wylde Audio (5)Yamaha (5)Play as you Pay® Eligible4-Payment Plan (542)6-Payment Plan (921)8-Payment Plan (885)12-Payment Plan (743)By Price$100 - $149 (5)$150 - $199 (19)$200 - $299 (24)$300 - $399 (60)$400 - $499 (73)$500 - $749 (183)$750 - $999 (233)$1000 - $1999 (245)$2000 - $2999 (93)$3000 - $3999 (65)$4000 - $4999 (34)$5000+ (13)Availability In Stock Items (860)Clearance Gear (229)By ConditionNew (914)Blemished (221)Scratch and Dent (18)Viewing products that ship to: Customer Kudos "zZounds is the best online company I've ever dealt with hands down." - Customer on October 21, 2017 1 MILLION+ Happy Customers learn more Guitar·Bass·Keyboard·Recording·Computer Audio·Live Sound·Drums·DJ·Accessories

This kit contains everything you need to build your guitar.  Just add your finish materials to the body and neck.  These kits aren’t just a collection of random parts- each neck has been custom fitted to the body to ensure a good, snug fit.  Includes a finished, predrilled body, fretted neck, all electronics and hardware. Wood is raw and unfinished, may require sanding and patching or other preparation prior to applying a finish.
Every beginner guitarist deserves to learn on an instrument that's built by experienced craftsman who use only the finest materials. However, for many novice players, it's difficult to know for sure what's considered a high quality instrument. To make things easier, many popular guitar brands offer guitar value packages. These packages consist of all the essential pieces of equipment that a learning guitarist would use in the developmental stages of their playing. Within this section, you'll find more than enough guitar value package options to choose from.
While it might look identical to the RevStar RS420, Yamaha Revstar RS320 is very different. The shape is the same, along with the most of the hardware. However, the tone is a whole different story. While RS420 comes with vintage humbuckers, the RS320 packs a set of extremely hot pups which are more modern. I personally liked this configuration more than the vintage one, simply because it offers extended versatility.

There are many similarities between the two designs, such as the exquisite detail of the visual appointments, from the bound necks and headstocks to their trapezoid and block inlays.  They both include separate volume and tone knobs for each of the two humbuckers, which can be switched between or used in conjunction with the 3-Way Toggle switch.  Once you get your hands on one, the differences become apparent quickly though.
Launch price: $2,099 / £2,499 | Body: Ash | Neck: Roasted maple | Scale: 25.5" | Fingerboard: Roasted maple | Frets: 22 | Pickups: Music Man SH single coil, Music Man SH humbucker | Controls: Volume, tone, 3-way selector switch | Hardware: Music Man Modern hardtail bridge, Schaller M6-IND locking tuners | Left-handed: | Finish: Trans Buttermilk, Trans Black, Trans Maroon, Satin Natural
The electric guitars have to be plugged in for sound to be produced. A cable and an amplifier are a must for them to produce sound. They are largely dependent on some electronic pickups, having between one and three pickups on their bodies, for them to produce this sound. They are relatively much lighter and have lighter gauge strings when compared with their acoustic counterparts. It is therefore a better option for the small statured or small-handed players. Getting comfortable to hold a guitar or fret the notes is quite physically challenging when working with the acoustic guitars than with the electric types.

GuitarPCB.com – designs and sells printed circuit boards (PCBs) with a boutique look for classic and boutique pedal designs. Their active forum provides support for builders using the PCBs. A theme throughout their site is that you expensive boutique pedals are simply classic older designs with little or no modification, and you can easily build your own.
Analog overdrive/distortion pedals work on similar principles to preamplifier distortion. Because most effects pedals are designed to operate from battery voltages, using vacuum tubes to generate distortion and overdrive is impractical; instead, most pedals use solid-state transistors, op-amps and diodes. Classic examples of overdrive/distortion pedals include the Boss OD series (overdrives), the Ibanez Tube Screamer (an overdrive), the Electro-Harmonix Big Muff Pi (a fuzz box) and the Pro Co RAT (a distortion). Typically, "overdrive" pedals are designed to produce sounds associated with classic rock or blues, with "distortion" pedals producing the "high gain, scooped mids" sounds associated with heavy metal; fuzz boxes are designed to emulate the distinctive sound of the earliest overdrive pedals such as the Big Muff and the Fuzz Face.[citation needed]
I have been playing guitar, banjo, bass and harmonica for 46 years - and I don't find a $4,300 Martin D 41 to be affordable (Guitar Center price). I play a Taylor 402ce and a dozen other instruments. I believe Taylor is the best instrument for the price..Alvarez Yairi guitars are very good too. Martin and Gibson make fine guitars but they are overpriced. I have a Chinese Maple Guild that sounds fine but the fretwork is amateurish. A Chinese Takamine New Yorker is very well constructed and sounds great.
MAKE YOUR OWN BODY BLANK Another neat trick to create your own body blank for $10 is to get a 3/4" thick peice of Birch Plywood that comes cut into a 4' by 2' board. Simply cut out two rectangular sections of the board that will accomodate your desing and wood glue them together. Be generous with the glue to make sure there aren't any spaces between the boards when you press the two together, clamp and stack weights on top of it so the two peices are joined firmly and let dry overnight. This gives you a a 1 1/2" thick body blank that is rigid and works great for electric guitars. You will have to go with a solid color paint when you finish it but you won't be able to tell the difference between it and the solid wood blank. Plus you'll save a good chunk of change that you can use towards good pickups and hardware. If you want to make the body a little thicker, you can get a 1/4" peice of birch and glue it between the two thicker peices. It's also a good idea to prerout any wire cavities in that 1/4" peice before you glue them together. That way you don't have to worry about drilling them later and ruining the top of your guitar body with the drill.
There’s a lot of knowledge here to digest, so the best advice anyone can give you is not to sweat it too much. You aren’t going to become a pedal encyclopedia overnight, and even if you could, you’d be missing out on the fun experience of trial and error that comes with figuring out your first pedals. The truth is that some of the most distinctive guitar and bass effects ever recorded have been the result of artists experimenting with effects units they’d never used before – especially in the 1960s, when pedals were brand-new to everyone.
What the hell!?!? Jimmy page is the greatest guitarist ever! And this is coming from a guy who has listened to many many types of music... Page is one of the reasons I fell in love Led zeppelin... From Hendrix to Vaughan to Clapton to slash to Johnson to sambora to gilmour to Santana nobody mesmerised me more than page did... He made his guitar TALK. Phhff, bucket head? Gimme a rest! Just give a listen to Achilles last stand or any song from led zeppelin 1, 2, 4, HOTH or Physical Graffiti. In my view all of the albums led zeppelin had produced rocked! Page forever!
Bob, 66 is not too late to start playing. I play classical guitar, my preference and I -also play steel string scoustic guitar. I own a Taylor because it lends itself nicely to finger style picking (carried over from my classical guitar. I play with a harpest who did not begin playing until she was 73. She is now 86 and plays someplace almost every day of the week. It's never too late to begin. Go for it I'm 69 and playing more gigs than ever.
Finally, vintage gear tends to display more variation from unit to unit relative to modern gear. Fifty years ago the technician winding pickups might have been distracted and left the pickup on the winding machine a little longer then normal, resulting in a coil with extra windings of wire and a hotter output. Modern standardization is usually a good thing-you’re less likely to encounter unwanted surprises. On the other hand, the relatively casual standards of the past sometimes resulted in happy accidents.
You can assemble your own system from disparate components, hardware and software, and spend a lot of time and confusion getting them all to work together. But the easiest and ultimately most cost-effective route is to purchase one of the least-expensive Apple Macintosh computers, all of which come with Apple's free GarageBand software installed. This will provide you with a wealth of tools for amp emulation and effects in an integrated environment for multi-track recording and editing (and it includes a wealth of drum machine, synthesizers, and sampled instrument libraries as well.) If you outgrow Apple GarageBand, you can suppliment it by purchasing Apple MainStage for $30 and/or Apple Logic Pro for $200.
The Takamine brand helps prevent big brand manufacturers from setting their prices too high - by showing them that great guitars can be produced at reasonable prices. On top of their bang per buck reputation, Takamine is considered as the pioneer of installing built-in pickups into acoustics, something that is now a common configuration offered by majority of guitar builders. The Takamine P3NY showcases how impressive tonewoods and electronics can be implemented without ridiculously jacking up the price.
While it may sound like a good idea to place a booster pedal towards the front of your chain in order to send that added voltage out from the get go, some pedals can’t handle high levels of voltage which can cause feedback and other problems. Also, you don’t want to simply place it at the end as there is not much benefit in adding voltage when the signal has already lost much of its clarity. It would be like enlarging an already fuzzy picture when what you really want is to keep it from getting fuzzy in the first place.
That’s not an overstatement, as traces of T-Bone’s influence can be heard in the early recordings of Albert, B.B. and Freddie King, Muddy Waters, and especially Chuck Berry, who adopted many of Walker’s signature licks as his own. A sharp-dressed, flamboyant performer who played the guitar behind his head and did the splits without missing a note, Walker helped reposition the guitar player from the sidelines to center stage, inspiring Buddy Guy, Jimi Hendrix and Stevie Ray Vaughan to copy his impossible-to-ignore moves.
One thing is for sure: the advantage of a multi effects pedal is getting a lot of effects in one convenient package, which you can use to learn what guitar effects you actually use on a regular basis. Depending on the type of music you play, your style, and your skill level, chances are you don’t have a need for every effect type under the sun. Pro guitarists’ pedalboards are tailored to the tone and sound they need to achieve. Perhaps fuzz, delay, and compression are crucial, but not a flanger or chorus. Point is, if you don’t yet know this about yourself, a multi-effects pedal is the most perfect and cost effective way to start. Over time, if and when your love for effects deepens, as your budget allows you can start buying individual pedals that are better versions of what’s on your multi-fx unit. The overdrive in your Zoom G3X might be good enough to hold you over, but eventually you might want to get an actual Ibanez TS9 Tube Screamer.
Yamaha Company is known as the largest music instrument production firm in India. It offered huge variety of guitars at starting prices around Rs 8,000.The topmost guitar models of this firm are SG 7, RGX, SG 5 and Yamaha RGZ. This brand is earning good reputation by offering high quality guitar to its customers. So, if you are a new learner, then may buy this best guitar at fewer prices.
It can be tough to know where to start when you’re looking at as many options as there are in the world of effects pedals. In fact, your first pedal may not even be a pedal at all – many amplifiers have built-in effects sections so you can get your introduction without having to attach an external stompbox. But if you have a more straightforward amp, or if you’re ready to try effects units that go beyond its built-in capabilities, there are some great varieties for novice users. And don’t forget that you can always look up the preferred pedals of your favorite guitar hero to inspire your own collection.
Accompanying the Tempo guitar was the Merson Tempo Guitar-Amp. This was a tube amp with two instrument and one microphone input, heavy-duty 8″ Alnico 5 speaker, volume and tone controls, and a pilot light. The cabinet was covered in two-tone leatherette. The picture is in black-and-white, but the look is remarkably like Premier amps of the time, so a tan and brown color would not be a bad guess. The speaker baffle featured a classical guitar design (!) with “Tempo” written in little circles on the bridge! Substitute a lyre for the classical guitar and you’d swear this was a Premier, made by Manhattan neighbor Multivox, so that might, indeed, be the story there.

I have had an old beat-up non-functioning norma electric archtop (hollow body) since i was 13(in 1984). A friend gave it to me and said i could have it if i could fix it... well like 20 years later i fixed it! and had the electrical redone for like $60.00. it needed some new parts (basiclly EVERYTHING) but i really wanted an archtop and knew i could fix this one up to sound pretty cool.... what i have found out about these guitars is that they really arent worth anything... i thought this one may have been from the late 50's early 60's so i may be worth something.. but as it turns out most people i have talked to about restoring it says its not worth anything that they were just little copies made in the 50's-60's and bought in the US at probably sears or something.... oh well I DONT CARE i really like it and its made well, so for the sheer vintage look and great feel I LOVE IT!-jj

Regarding truss rods, all vintage Martin instruments post-1934 have *non-adustable* truss rods (T rod). This means the neck better be straight, otherwise an expensive repair will be in order. To check neck straightness on a guitar, first tune the guitar to pitch. Then hold the low-E string down at the 1st and 14th frets. Note the distance between the bottom of the low-E string, and the 7th fret. You should be able to put a medium guitar pick in this space. Any more, and the neck is "bowed". Any less, and the neck is "back bowed". Repeat this with the high-E string (the same results should be seen; if not, the neck has a "twist" to it).
Distortion and overdrive are forms of audio signal processing used to alter the sound of amplified electric musical instruments, usually by increasing their gain, producing a "fuzzy", "growling", or "gritty" tone. Distortion is most commonly used with the electric guitar, but may also be used with other electric instruments such as bass guitar, electric piano, and Hammond organ. Guitarists playing electric blues originally obtained an overdriven sound by turning up their vacuum tube-powered guitar amplifiers to high volumes, which caused the signal to distort. While overdriven tube amps are still used to obtain overdrive in the 2010s, especially in genres like blues and rockabilly, a number of other ways to produce distortion have been developed since the 1960s, such as distortion effect pedals. The growling tone of distorted electric guitar is a key part of many genres, including blues and many rock music genres, notably hard rock, punk rock, hardcore punk, acid rock, and heavy metal music.

According to Wikipedia, a grimoire is a magical text that instructs the user “…how to perform magical spells, charms and divination, and how to invoke supernatural entities…” In order to summon your own supernatural creations, this guitar-focused text compiles a vast selection of exercises that will help you connect patterns across the entire guitar neck.
With the massive range of options available, you'd have to spend the whole day here to go through every one. There are six and twelve-strings, models specifically made for beginners, limited edition double necks; you name it, you'll find it! For a real classic, strap on a Rickenbacker 330 electric guitar. A staple in 60's mod culture, the unique hollowbody construction, slim neck and contoured body make the Rickenbacker 330 so easy to play that it has held the status as one of the all-time greatest guitars for decades.
I have been playing guitar, banjo, bass and harmonica for 46 years - and I don't find a $4,300 Martin D 41 to be affordable (Guitar Center price). I play a Taylor 402ce and a dozen other instruments. I believe Taylor is the best instrument for the price..Alvarez Yairi guitars are very good too. Martin and Gibson make fine guitars but they are overpriced. I have a Chinese Maple Guild that sounds fine but the fretwork is amateurish. A Chinese Takamine New Yorker is very well constructed and sounds great.
The downside of going electric is that now you have to think about a soundboard, or at least an amp. And no self-respecting guitarist can live without a few pedals to tweak the sound. I mean you only need a volume pedal to control the level, a tuner might be nice, chorus is always appreciate, a nice delay pedal wouldn’t be bad, and you might need a clean boost for those solos. Then again, you might just want to plug straight into the soundboard and just enjoy that amplified acoustic sound.

Popular Categories: Body and Skin Care Air Conditioners Air Purifiers Anti Pollution Mask Cameras External Hard Disks Eye Care Face Cream Face Pack Face Scrubs Face Wash Fragrances Gaming Console Hair Care Hair Conditioner Hair Gel Hair Oil Health and Nutrition Health and Wellness Health Food and Snacks Laptops Makeup Mobiles Pen Drives Personal Care and Beauty Power Banks Protein Supplements Refrigerators Shampoo Smart Assistants Smart Watches Speakers Tablets Televisions Toiletries Toothpaste Washing Machines Water Geysers Water Purifiers Women Analog Watches
Wengrow said that Gibson got outmaneuvered by its competitors. “In the 1950s and 60s, it was really just Fender and Gibson as the two main guitar makers and they became the standard bearers. But other guitar makers such as Ibanez, Jackson, Yamaha and Paul Reed Smith, came to existence and copied their standards but continually updated many features and customizations that better reflected the idiosyncrasies of the times, often for cheaper prices.”
Neither should you confuse acoustic-electric guitars with semi-acoustic hollow or semi-hollow instruments. Acoustic-electrics are acoustic guitars with onboard electronics that allows them to be amplified. They can be played just as well without plugging in. Semi-acoustics are electric guitars with some acoustic properties that are meant to be amplified when played.
A little bit of history will make this clearer… The original Fender Stratocaster switches were 2-pole 3-way switches (that’s actually what I have on my schematic, I think you’ll see why in a bit) and were intended only to select either the neck, middle or bridge pickup. However these were “make before break” switches where, as the switch is moved across from one position to the next, the next contact is made before the previous contact is broken. People found that if you could get the switch to rest in between those three positions that you’d actually have both neck and middle or middle and bridge pickups connected at the same time and, most importantly, it sounded good! It became a common thing to rest the 3-way switch in between the positions, so common that in the 60’s people were filing notches in the detente mechanism of the 3-way switch. These became the “notch” positions. In the 70’s, Fender adopted this popular mod into their stock switch thus becoming what we now use and call a 5-way switch but is, in fact, a 3-way switch with 5 positions.
If you are a first time builder or an experienced professional you know the value of building your instrument on a solid foundation. The Custom Shop Jag body is beautiful, high quality and made to spec. The Allparts neck is manufactured under license by Fender. The materials and quality level meet the standards set by Fender. Using these high quality materials will give you the sweet tone and sustain you are looking for.

My granddaughter really liked this book. I know it was used but the CD and the wall chart were missing. I wish that would have been noted in the comments. Some of the other book sellers noted that one or the other of these were missing so I didn't order from them. Nothing was noted in the comments on this. My granddaughter was happy with the book and wanted to keep it.

Here I'm going to look at all of the different kinds of pedal available on the market. Hopefully this will help act as an effects pedal guide to beginners who are looking to buy their first pedal, and just don't know where to start. We'll look at the name of the effect, what it does, and an example of the pedal (mostly Boss and MXR pedals as they're probably the best known). Oh, and I won't be looking at any of the niche boutique pedals; that would take ages!


Many Rickenbackers — both guitars and basses — are equipped to be compatible with a “Rick-O-Sound” unit via an extra “stereo” output socket that allows the two pickups (or neck and middle pickup combined/bridge pickup, in the case of three pickup instruments) to be connected to different effects units or amplifiers. Another idiosyncrasy of Rickenbackers is the use of two truss rods (rather than the usual one) to correct twists, as well as curvature, in the neck.

Fret gauge might have a bigger impact on playing feel than on tone for many guitarists. Wider frets are often attributed a smoother, more buttery playing feel, which also makes it easier to bend strings. Ease of bending is also enhanced by taller frets, whether wide or narrow. Narrow frets shouldn’t be too hard to bend on, unless they are badly worn down, and they also leave a little more finger room on the fretboard—particularly in the higher positions— which might suit some players better.
“Ceramic is a much more powerful magnet again [than Alnico V]. The bass and treble get boosted significantly. A lot of people think ceramic magnets scoop the mids out, but when you analyse it you find the mids tend to stay where they are – it’s just that the bass and treble get boosted so much you get a V-shaped taper in the EQ. Ceramic pickups tend to suit players who need a very fast and percussive pick attack.”
Fall 1954: both models have 2 volume and tone knobs, $39.95 and $59.95 respectively. The single cutaway bodies were made of solid Poplar wood, and are known as the "peanut" body shape at 11.25" wide. Then used a solid aluminum bar running from the peghead to the bridge for strength. "Coke bottle" pegheads are used that are 5/8" wider across the two "E" tuners than the later "Coke bottle" peghead shape. This model was also available under the Silvertone brand name with the "lightening bolt" peghead.
We spent 45 hours on research, videography, and editing, to review the top choices for this wiki. One of the best things about an electric guitar is its portability. Most times, however, you can't say that about the amps you need to go along with them. Fortunately, these mini amplifiers have come along, developed by the top names in full-size models, and offer incredible sound quality in an exceedingly portable package. We've ranked these micro monsters by tonal character, power, and control. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best mini guitar amplifier on Amazon.
DRILLING THE NECK HOLES ON THE BODY Before you do this you can carve down the back of the neck area if that is something you were going to do. If you are just going to leave it flat then that's ok too. The first step if you are using furreles is to map out where you want to place them and then mark the center of the hole where the screw will go. Then take your forstner bit drill enough to fit the furrele inside. Usually you can tell how deep to go if you drill a little at a time, and place the furrele in it to see if it is just low enough in the hole not to see the top of it if you look at the body horizontally or it is flush with the wood. After doing this you can drill the holes for the screws. Use a bit that has the same circumference as the screw including the threading so when you put the scre into the hole it just passes through with out you having to screw it in. Drill in the indention that was left by the tip of the Forstner bit, keeping the drill as straight as possible.
Overstock SaleNew ProductsVacuum TubesSpeakersAccessoriesAmplifier PartsBooks & DVDsCapacitor Amplifier SetsCapacitorsCoversEffect Pedals & PartsEnclosuresFootswitch BoxesGift CertificateGrill Cloth, Tolex & PipingGuitar PartsHardwareJacks & PlugsKeyboard PartsKitsKnobsLuthier ToolsMaintenance ProductsPMT Tone ModsPotentiometersPower AccessoriesRadio & Antique Equipment PartsResistorsReverb TanksSemiconductorsSpeakersSwitchesT-shirts/GiftsTech SuppliesTerminal Boards & StripsTransformers & ChokesVacuum Tube AccessoriesVacuum Tube Amplifier SetsVacuum TubesYellow JacketsZero Glide Nuts
Another Martin creation, the 000 shape guitar is almost the perfect halfway house between a dreadnought and a parlour. Its classic hourglass figure meant it sat comfortably on the knee, endearing it to players of folk and other fingerpicking-heavy styles of music. The shape ensured it had the perfect balance between playing and comfort, and was often seen on the lap of no less a player than Eric Clapton. However it wasn’t averse to a bit of heavy strumming when the occasion called, and it’s large bottom end ensured it could keep pace when playing with others.
The tone selector on an electric guitar controls the capacitor, which basically filters out high frequencies. The same way a high-cut filter (or low-pass-filter if you prefer) works on a standard equalizer. By dialing down the tone, you remove brightness and treble. The pickup selector does just what it's called.. Selecting which pickups being used to capture the vibration of the strings, and translates the energy into electric current, though the configuration and number of "presets" can vary from guitar to guitar, depending on how many pickups it has etc. If you're a handyman you can even configure this yourself.
*When the item leaves our warehouse, they are generally shipped to EMS Worldwide Express Mail Service and it would usually take 7 – 10 days to United States. We ship our products from Mainland China where our manufacturing factory is located. We will inform you once your order has been shipped and we will be providing you with the tracking number so you can conveniently monitor the shipments progress on EMS Worldwide Express Mail Service website or SF Express and USPS and Parcel Force website.

Automatic Track Creation & Loop Recording: A new layer (track) is created each time you start recording and each time a Riff loops. Stack layers on top of each other (bass, guitar, vocals) to create a Riff. Use looping to create multiple tracks, do multiple takes, etc. Each layer has controls for mixing and effects. (4 tracks with T4, 24 tracks with Standard)
FX or no FX? Again, it's almost a question of valve or solid state, here. Most valve amps don't come with any effects other than tremolo and reverb, at most. Solid State amps often come with a wide range of features such as digital FX and amp modelling. If you're an have lots of fx pedals, you don't really need a modelling unit, but if you're new to guitar playing, buying an amp with modeling FX might be a good way to get familiar with all those sounds.

But there are more questions – are you a beginner, or do you have 20 years playing experience under your belt? Are you on a tight budget, or is money no object? Do you prefer funk, or are you a full-on metalhead? Somewhere the perfect guitar is waiting for you, and – with hundreds of reviews on this site – chances are we have featured it on these pages!


These negative reviewers don’t understand that their guitar arrived exactly as most mail-ordered guitars arrive: out of tune and probably needing a full setup by a professional guitar tech. That’s just the reality of the world we live in: mail-ordered guitars are rarely setup properly before they’re shipped, and even if they are they can get knocked out-of-whack during shipping. So when your guitar arrives, know that it’ll probably be out of tune, might buzz a bit, and it may need a full setup to play its best. Very seldom are these things the result of a defective or damaged guitar.
For instance, during 1970s and early 1980s, Japanese manufacturer Tokai Gakki produced superb replicas of 1957–59 vintage Les Pauls, and replicas themselves were gradually highly regarded. In the 1980s, to respond to the high demand for vintage models, Gibson itself began to offer a line of “Custom Shop models”, almost accurate reproductions of early Les Paul crafted by the Gibson Guitar Custom Shops.
The Orchestra Model (OM) shape, with its sleek look and versatile acoustic voice, is one of C.F. Martin & Co's most popular guitar shapes. A number of iconic guitarists prefer this particular line, including legends like Eric Clapton and his protégé, John Mayer. I for one own an all-solid wood Martin OMCPA4, and it continues to exceed my expectations. While I have no regrets over my guitar, I have to admit that if I had the funds, I would have gone for the definitive Orchestra Model, the OM-28 E Retro.

Understanding how to read electronics schematics is the key to being a successful DIY pedal builder. A schematic will show you what components are needed for the build, as well as how these parts are hooked together to create (in this case) an effect pedal circuit. At first glance, a schematic may look like a bunch of hieroglyphics, compiled of various symbols, numbers, and letters (see below). Don’t fret! – After a bit of practice, you should develop a basic understanding of how a schematic works, and you will be putting together DIY effect pedals in no time!


{ "thumbImageID": "LC100-Classical-Guitar-Natural/518978000010000", "defaultDisplayName": "Lucero LC100 Classical Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Natural", "sku": "sku:site51274115036014", "price": "99.99", "regularPrice": "129.99", "msrpPrice": "259.99", "priceVisibility": "1", "skuUrl": "/Lucero/LC100-Classical-Guitar-Natural-1274115036014.gc", "skuImageId": "LC100-Classical-Guitar-Natural/518978000010000", "brandName": "Lucero", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/LC100-Classical-Guitar-Natural/518978000010000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black", "sku": "sku:site51274115036008", "price": "99.99", "regularPrice": "129.99", "msrpPrice": "259.99", "priceVisibility": "1", "skuUrl": "/Lucero/LC100-Classical-Guitar-Black-1274115036008.gc", "skuImageId": "LC100-Classical-Guitar-Black/518978000001000", "brandName": "Lucero", "onSale": "true", "stickerDisplayText": "On Sale", "stickerClass": "stickerOnSale", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/LC100-Classical-Guitar-Black/518978000001000-00-60x60.jpg", "imgAlt": "" } ] }
A final tip: not a lot of people know this, but Antares Auto-Tune works rather well with electric guitar. Of course Auto-Tune is monophonic, so it will dutifully ignore chords and double notes, but it will come into play when it detects a single note. You might reasonably ask whether a guitar tuner might not be a wise investment, but the reason I suggest Auto-Tune is not to compensate for a badly tuned guitar, but rather to pull imprecisely bent guitar stings into pitch.

The Truetone Rock Star has a classic 1960s Fender Jaguar - inspired body with a cherry & black sunburst finish and swank natural wood grain finish neck. The headstock has an odd, but killer-looking shape, an elaborately cut pick guard and what might be the world's coolest pickup; a chrome-cased body with a shimmery red marblized pickup cover. The guitar is 100% original with no replacement parts. We  rescued this one a while back and it was rusty and did not work when first tested. We meticulously detailed and cleaned it and removed the rust. We also re-soldered a few wires inside, and this fab Japanese guitar was ready to rock again. It sold and was shipped France, and the Rock Star is pretty rare, but there are lots of cool retro Truetone / Silvertone Japanese Guitars for sale below! Scroll Down for more from our collection!
If you’ve never listened to Chet Atkins, you should do it right now. The rockabilly player was a skilled instrumental guitar player, playing most of his songs without any backing from other musicians. For a great sample of his talent, give a listen to his version of “Mr. Sandman.” His alternating thumb rhythm and syncopated melodies are marvels of beauty and precision on the instrument.
One user summarizes market sentiment nicely by saying that the Yamaha THR10C is a phenomenal amplifier. Many of the commendations point to its great balance of sonic versatility and portability as its main strength, while others are pleased with its sound quality. Even experts are amazed by how it sounds, including Nick Guppy of Music Radar who commends it by saying: "While there are many small modelling amps around today, few of them look or sound as good as the THR." Build quality, USB recording convenience and the ability to run on batteries are also well received.

This is an American brand of guitar that is available in India. It was created in the year 1873. After a few years, it was bought by Gibson Guitar Corporation. Epiphone has a compact non-cutaway body made entirely from laminated mahogany. The neck features smooth slim taper profile, fretboard made of rosewood and 20 frets. Epiphone guitars India price starts from 14,000 INR approximately. This is the brand of guitar that is nylon strung and offers highest standards in acoustic and electric guitars.


Thought you'd like to know. Before Christmas, I stopped by a local music shop to buy my 12 year old granddaughter a new guitar to replace an old Beaver Creek she'd been banging on for a few years. Since I'm an old folky from the 1960s, I thought a low end Gibson or Martin would give her both good sound and some bragging rights at her school's guitar club. The shop owner was in the acoustic guitar room strumming something I had never seen before and quickly told me I should forget Martin or Gibson and get what he was playing. It was a Seagull. An equal sound for half the price, he said, so I looked it over, strummed the few chords I could remember, and bought it on the spot. Later, I was still pondering how a little Canadian guitar could be called better than a Martin or Gibson when I found your ratings post. I do believe I kept repeating "Oh my God, it's true!" over and over. And she loves the guitar, especially the smaller neck and fuller sound. Thanks for helping this old folky who always thought Martin and Gibson were names to be spoken in hushed reverence believe in something new.


I wish I had a cool story to attach to this guitar, but really this one is a history lesson regarding the development of Japanese guitar manufacturing.  Plus, it’s an example of some rare component combinations (like the pickups) that make guitars like these worth buying.  THEY’RE SO CHEAP!!  Hell, buy one of these for $200, send it to Dano and sink another $100 into it, and you’ll have yourself one hell of a player!  It’s like recycling, dude.
As for necks, the majority of guitars will have either a maple or mahogany neck, with a rosewood, maple or ebony fretboard. Again, there’s no right or wrong, and a neck wood is never going to sway your decision. But you should choose something that feels smooth and comfortable to play. There are a variety of shapes and profiles, and what you go for will depend on personal preference and playing style. For example, a modern C-shaped neck is always a safe choice as the majority of guitarists will feel comfortable using it, while a thin U-shape is great for faster players (think punk rock and metal).
Those aspiring to kill the next-door neighbour’s lawn by the malevolent force of their playing alone would do well to speak to their local dealer about Schecter’s Demon-6. Updated with fresh set of Schecter active humbuckers and a super-smooth wenge fretboard for 2018, the Demon-6 is a mean- looking S-style that’s built for shredding  - and it’s also available as a seven-string for a little extra. It’s one of the most powerful and playable instruments on the market at this price. Its thin-C profile neck, cut from maple with a satin finish, is super-quick. Shredders will love that a light touch is rewarded on the fretboard - that wenge feels slick ’n’ slinky. The bridge’s construction fits the two most important tenets in bridge design: it’s no-fuss and industrial-strength. The Demon-6 feels indestructible. It might make you feel likewise; at least, its active pickups (powered by a nine-volt battery that’s easily accessed via a clip on the rear of the instrument) will ward off most predators if you crank the gain high enough. Tonally, that’s the Demon-6’s wheelhouse. The bridge ’bucker has plenty of grunt but an abundance of top-end that metal soloists will love. Overall, the Demon-6 is a metal guitar, designed to summon something much more sinister, and it delivers in spades.
Sometimes people forget that the greatest musician is not the one who can plays faster. I play guitar and I admire who plays fast, but i admire more the ones who can make beatiful music, even if it's simple. Frusciante is one of the few guys who can do so (beside Hendrix). And Frusciante could play all of Jimi's songs when he was 12 years old, and I guess he still can. So for those who compare them to Steve Vai, you should listen to music and not watch to the speed of their fingers.

{ "thumbImageID": "Omen-Extreme-6-FR-Electric-Guitar-See-Thru-Black/520222000011000", "defaultDisplayName": "Schecter Guitar Research Omen Extreme-6 FR Electric Guitar", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "See-Thru Black", "sku": "sku:site51274115040642", "price": "449.00", "regularPrice": "449.00", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Schecter-Guitar-Research/Omen-Extreme-6-FR-Electric-Guitar-See-Thru-Black-1274115040642.gc", "skuImageId": "Omen-Extreme-6-FR-Electric-Guitar-See-Thru-Black/520222000011000", "brandName": "Schecter Guitar Research", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Omen-Extreme-6-FR-Electric-Guitar-See-Thru-Black/520222000011000-00-60x60.jpg", "imgAlt": "" } , { "name": "Vintage Sunburst", "sku": "sku:site51289600495695", "price": "449.00", "regularPrice": "449.00", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Schecter-Guitar-Research/Omen-Extreme-6-FR-Electric-Guitar-Vintage-Sunburst-1289600495695.gc", "skuImageId": "Omen-Extreme-6-FR-Electric-Guitar-Vintage-Sunburst/520222000001000", "brandName": "Schecter Guitar Research", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Omen-Extreme-6-FR-Electric-Guitar-Vintage-Sunburst/520222000001000-00-60x60.jpg", "imgAlt": "" } , { "name": "Black Cherry", "sku": "sku:site51274115040516", "price": "449.00", "regularPrice": "449.00", "msrpPrice": "649.00", "priceVisibility": "1", "skuUrl": "/Schecter-Guitar-Research/Omen-Extreme-6-FR-Electric-Guitar-Black-Cherry-1274115040516.gc", "skuImageId": "Omen-Extreme-6-FR-Electric-Guitar-Black-Cherry/520222000127000", "brandName": "Schecter Guitar Research", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/Omen-Extreme-6-FR-Electric-Guitar-Black-Cherry/520222000127000-00-60x60.jpg", "imgAlt": "" } ] }
Every new 2008 Les Paul Standard will benefit from Gibson’s proven chambering technique, which leaves each guitar with perfect tone, balance, and weight. Prior to gluing the maple cap on top of the mahogany body, the expert craftsmen at Gibson USA carve out carefully mapped-out chambers in the body using a Computer Numeric Controlled (CNC) router. The positioning of the routes was established after careful examination of the resonant characteristics of the Les Paul. Gibson approached this process with the awareness that every change to the formula would have repercussions on the instrument’s sound. So, in addition to relieving the stress on a player’s back and shoulder, these lighter Gibson guitars also enhance the tone palette in a manner unique only to these guitars. The results are comfortable, lightweight guitars that are acoustically louder, with increased sustain and resonance.
“Back in the fifties and sixties, you could tell what studio they had been recording in just by listening to the song,” Dr. Susan Horning Schmidt says. She is a professor at St. John’s University who has researched and written extensively about sounds and the recording process. During the period Dr. Horning Schmidt is referring to, the recording facilities were also physically bigger and bands often played together in a more live-type setting. Horning Schmidt states that “there’s a lot more space in the recording, a lot more acoustical space and dynamics.” Unfortunately, we’re losing that space with contemporary recording and production techniques.
I've spent a few weeks on this kit - I will update with progress. Cutting out the headstock and finishing the guitar was fun and not too difficult. I chose to use TruOil and a natural finish, which takes a few weeks to finish. The body I got was made from 4 pieces of joined wood, and I wasn't careful about checking for glue spots, so there are a couple in the finish, but it still looks great. The neck fits nicely and feels good. It is straight and correctly set up for string tension (a little bit of bow before the strings are on).
Richard Thompson has been one of rock's most dazzling stylists since his days with Fairport Convention, a British folk-rock band that veered into English traditional music. Shooting out life-affirming riffs amid lyrics that made you want to jump off a bridge, he combined a rock flatpick attack with speedy fingerpicking. His electric-guitar solos, rooted less in blues than in Celtic music, can be breathtaking, but his acoustic picking is just as killer; no one knows how many tears have been shed by players trying to nail "1952 Vincent Black Lightning."
Hertz Guitar is a well known brand, which manufactures high quality guitars. The company was originated from Shanghai,China and North Korea. Their musical instruments were introduced on September 2009. They offer world class quality instruments from world class branded production houses. They maintain international standard. It mainly focuses on musical instruments as well as accessories. They manufacture a wide range of guitar. Available at below Rs. 12,040/- (approx).

As successor to the Bogner Triple Giant, the Fish is a pre-amp with a legendary status, due to it’s unique character and it’s 4-channel configuration. Originally introduced in 1990, the unit was limited to 250 pieces, and is a rare find now-a-days. But thankfully, Bogner decided to reintroduce the Fish, featuring a “Country”, “Shark”, “Strato”, and “Brown” channel. Just like the original, this amp can take on just about any style you throw at it!


It’s provided as-is with no support, but it’s still well worth checking out if you’re on a PC. According to the developers, it was born inside an academic research project about the modelling of electric devices, and then applied to the musical instrument field as an evolution of the techniques available in commercial units. Its most important feature is the high precision of the simulation.
OM-42PS: Paul Simon’s signature acoustic model (manufactured in the 1997 model year) is based on the OM-42, which had not been manufactured since 1930. Alterations were specifically requested by Simon himself. From the original planned run of approximately 500, only 223 were produced, making these a collector’s item. A standard version of the OM-42 is in the current range.
 South Korea has been one of the largest OEM guitar factories in the world since 1980's. Nonetheless, the words "Made in Korea" still invoke visions of low cost alternatives to high-end manufacturers. At Swing, our mission is to lay these stereotypes to rest, and show the world that we can produce true professional grade instruments, made by professionals, for professionals. (Of course, company is not a patriotic organization. This is a matter of manufacturer's pride and self-satisfaction that can be called "Professionalism".)
Teisco produced guitars that were sold in the U.S. as Teisco del Rey as well as Silvertone, Beltone, Duke, Decca, Heit Deluxe, Jedson, Kimberly, Kingston, Lyle, Norma, Tulio and World Teisco, as well as some of the early Kents. At various times Teisco guitars were made for and sold under the now well-known Ibanez name. They have developed somewhat of a cult following in the U.S. which has resulted in some unrealistic prices for some models.
The SimulAnalog Guitar Suite is an old but still popular free guitar effects program. It contains a set of VST plugins that emulate some of the most common used guitar effects and amps. It has simulations of five essential guitar effects which include Boss DS-1, Boss SD-1, Tube Screamer, Oberheim PS-1 and Univox Univibe. The SimulAnalog Guitar Suite was born out of an academic research and thus applies a zero deception, no marketing hype approach. The interface is very basic but the sound is said to obtain lass than -40dB of difference compared to the original hardware.
Different types of guitars have different sound aesthetics, e.g. different colour-spectrum characteristics (the way the sound energy is spread in the fundamental frequency and the overtones), different response, etc. These differences are due to differences in construction; for example modern classical guitars usually use a different bracing (fan-bracing) from that used in earlier guitars (they had ladder-bracing); and a different voicing was used by the luthier.
For its tops (soundboards), Ovation used sitka spruce, a wood which Kaman engineers had been using in helicopter blades. In the 1970s, Ovation developed thinner sound-boards with carbon-based composites laminating a thin layer of birch, in its Adamas model, which has been viewed as one of the most radical designs in the history of acoustic guitars. The Adamas model dissipated the sound-hole of the traditional soundboard among 22 small sound-holes in the upper chamber of the guitar, yielding greater volume and further reducing feedback during amplification.[1] The Adamas design strengthened the sound-board, reducing the traditional design’s bracing and hence its weight. In the 1980s, another innovation was the introduction of shallow-bowl guitars, which appealed to electric guitarists.
Some Korean Ibanez serial numbers are purely numeric with no alphabetic characters. According to Jim Donahue these guitars were manufactured in the Cort factory, in which he had the supervision. Because they had no date stamps available when they started, the serials numbers of Artstar models in this factory were written by hand. These handwritten serial numbers are hard to decipher. The production of these Artstar models at the Cort factory was discontinued in 2003.
O.K. These are my first impressions of this guitar kit, my first, right out of the box. About me: I own about a dozen guitars, both acoustic and electric, including 6 string and basses. I know a little about construction, as I have been studying, and have been wanting to build my own guitar for some time now. Building from scratch seemed a little optimistic so I elected to go with this kit after studying the Internet for days. I wanted a chance for a great result with my mediocre woodworking skills. Kit arrived quickly and undamaged, good packaging and the components were bagged nicely.
About a year ago (or maybe more) I was in a real Marc Bolan/T Rex phase, and I came across a Lotus Les Paul copy in my local Sam Ash used for $199. Like the idiot I am, I played it, and it played and sounded good, so I bought it. Well, that did not sit well with my folks, who made me take it back a few days later. It had a bolt-on neck and was quite heavy, but other than that, it looked sweet. I even was smart enough to take a picture of it:
Based on Mesa's flagship Mark V, the Mark Five: 25 head is small, perfectly formed and typical of Mesa's superlative design and attention to detail. Two independent channels, each with three very different voice presets, combine with Mesa's iconic five-band graphic EQ for a choice of 12 sounds. You can footswitch between the channels, with the graphic on or off for quasi four-channel operation and preset 25 or 10 watts per channel. One of the best features lives on the back panel: a CabClone speaker-emulated direct output, with a speaker defeat for silent recording or practice, using the built-in headphone socket. Despite the Mark Five: 25's long feature list, it's very easy to use and its tones are sensational. The rhythm channel covers the shimmering clean tones of the modern Boogie and the fatter 'blackface'-inspired midrange of the fabled Mark I, while the Mark V crunch voice is so deep and three-dimensional you could record an entire album with it. The lead channel is equally inspiring, with a perfect rendition of the Mark IIC's overdrive tone (arguably the most coveted Boogie sound), along with more modern distortion effects that sound unbelievably good when tweaked with the graphic. The Mark Five: 25 is one of the best small Boogies we've ever heard, which means it's one of the best small amps there is.

Epiphone are a well respected subsidiary of Gibson, and have been making musical instruments since their founding in what is now Turkey, Europe, in 1873. After being acquired by Gibson in 1957, Epiphone are now best known for manufacturing affordable versions of some of the most iconic guitar models around, including the Les Paul and SG. However they do make a couple of original models, such as the Casino, which was famously used by the Beatles.
There's just no getting around the Martin brand when there's talk about good acoustics. And since we're talking about the best of them, it's not surprising to find their name filling up multiple slots in this list. The Martin DRS2 acoustic guitar is special because it gives us a true all-solid wood body Martin acoustic guitar - at a very reasonable price point, in the dreadnought shape that the company themselves developed.
The fretboard wood is used for the part where the frets are installed (front of the neck, where you press on the strings). All our fretboards are built from quality tone woods. If you're just starting out, we recommend you choose the wood that appeals to you most based on its appearance, and don't worry too much about how the type of wood affects the sound or performance of the instrument.
Though not much is known about the production of the Hi-Flier after about 1977, it clearly came to an end — and clearly has had an impact on players in the vintage market. Used by guitarists like Cobain and Lee Ranaldo of Sonic Youth, as well as many others in a variety of bands, the Hi-Flier gained notoriety as a unique guitar with a sound as striking as its looks.
Regarding the PDF download, I have not done so yet, but all of this info is available on the web, in color, ad nauseum. I bought the book to have at my bench so I could refer to it while wiring guitars. I do not have a color printer. I find the thought that, in order to experience what the book OUGHT to look like, you have to download a file, presumptuous, at best. Annoying, at the least.

This processor is pretty good quality, unfortunately not too many parameters on the effects and you can only use one effect at a time, and some prefixed combo of 2 effects (if i remember correctly 10 different options). If you need it for reverb, or slight delay, tremolo or acoustic simulator its pretty cool, not able to add exact tempo on delay or tremolo though. Sound quality is very good, 24 bit A/D and D/A so no loss there either, and you also have stereo (same effect options on both though) and balanced and unbalanced outputs (if you use unbalanced the signal goes to both outputs so you also have the balanced output if needed). For the money is definitely the best option, imagine that a reverb pedal cost the same money (just reverb)...so if you have a controller it will fit on your gear. I am using it with ... full review
Epiphone currently produces several models of the Les Paul including the entry level “Les Paul Special II”, which is generally made of a basswood body and a veneered top, a bolt-on neck (with dot inlays instead of the usual trapezoid inlays), lacks a binding, and has simplified electronics.[25] The next model up is the “Les Paul 100”, which costs approximately $US300, has similar features but it has the standard Les Paul wiring, mahogany body and a higher-quality paint job. The Epiphone Les Paul Studio is the least expensive Les Paul model to have a carved top and a set neck (features considered central to the feel and sound of more expensive Les Paul models), and is between $350–$400 depending on features and finish. The standard models are the “Les Paul Standard Plain Top” and the “Les Paul Standard Plus Top”. They cost $US550 and $US650 respectively. They both feature a solid mahogany body with a maple veneer and carved top; the “Plus” model includes a “flamed” maple finish while the “Plain” top is unfigured.[26]
this is literally the worst piece of cow dung in the industry. I wouldn't even call it a guitar, it's so poorly made. Management, especially the CEO, don't care a bit about quality, the only thing that matters is their unrealistically high production numbers. the production processes are so archaic they are amateur, and they have the audacity to call it the worlds finest guitar. all of this stems from the CEO and his manic psychotic neurotic management style (he has to sign off on EVERYTHING: new hires, transfers within the company, promotions, raises, budgets, any funding for new parts or machines.
This bass guitar amplifier features a 20-watt amplifier and an 8-inch driver. It reproduces frequencies from 70 Hz ~ 10 KHz with a total harmonic distortion of 0.5% (typical). It also has a built-in, switchable active compressor. It features a 3-band EQ, with the bass EQ centered at 100 Hz, mid-range EQ at 800 Hz, and a treble EQ at 6 KHz. It features a 3.5mm line output with an impedance of 1 kilohm, for directing the output signal to a mixer, recorder, or another amp. The 3.5mm stereo headphone output will defeat the internal speaker for quiet practicing.

The MESA Bigblock 750 has a built-in overdrive channel. The Mesa M2000 has a high gain switch which can be engaged with a footswitch. The Marshall MB450 head and combo bass amplifiers have a tube pre-amp on the "Classic" channel which can be overdriven. The Ashdown ABM 500 EVO III 575W Bass amp head has a built-in overdrive effect. Overdrive is also available on many Crate bass amplifiers. The Yamaha BBT500H has three types of built-in drive effects: overdrive, distortion and fuzz. The Ampeg B5R Bass Amplifier has two channels: clean and overdrive, with the ability to combine the two. Verellen, a boutique amp company, produces a bass amplifier with a built in overdrive channel.
GuitarFX™ guitar software (it's on the market since 1997!) enables you to turn your computer into a guitar effects processor. Simply plug your guitar into the microphone or line input of your sound card, run this software, then press "Start" button. To stop playbacking pre-recorded guitar sounds click once on a picture of a small red lamp placed left to fx-slot with "Playback wav" title. Enjoy real-time crazy distortion smoothed by power filters and shaped by multi-band equalizers! Author of GuitarFX™ offers several presets, including "hard rock", "high gain lead" and "solo" effects. However, you can click through several menus to easily create custom tones. They can be saved as pre-sets for future use. Pre-sets can be assigned to "hot keys" F1..F12. Among the effects, you can apply 4 types of distortion, noise gate, wah-wah, compressor, EQ, flanger, reverb, chorus, delay and a number of other filters and effects. You can save your recordings to your hard drive. GuitarFX has the "software effects chain builder" with 16 fx slots. Clean guitar signals go to the top fx slot, then they are passed through all fx slots from the top to the bottom and go to the sound card output from the bottom fx slot. You can move any fx slot up. To do this place your mouse cursor on the top part of the appropriate "Tune" button and then do right mouse button click. Also you can move any fx slot down. To do this place your mouse cursor on the low part of the appropriate "Tune" button and then do right mouse button click.
The "Slide Guitar Extension Nut" presents a bad case of convenience to the manufacturer (only having to make one size) disguised as a convenience to the customer (pretending one size fits all). This thing is not very versatile. With an outer string spread of 1.75", it's made for a wide guitar neck so if yours is only average, the outer strings will be suspended off to the sides of the overall width of the neck. That's not insurmountable but it's also not something every budding slide player wants to tolerate.
That it does, indeed. Acoustic design has been refined to reflect the best possible usage of materials and shape to get the most productive sounds and tones and, as you can see, it's pretty consistent. Wood is the predominant role player in an acoustic's construction, because it directly affects the sound. Only the best, resonant tonewoods would do and they were used to the hilt to make a good sounding instrument as the sound partially relies on it.
At the end of the day, this is obviously far from a perfect example, but this is an extremely hard-to-find factory left-handed 1958 Gretsch Duo-Jet, and provides a very rare opportunity for the vintage guitar collector, lefty or righty! I have seen far fewer left handed 50s Gretsch guitars as compared to Fender, Gibson, and even Martin over the years. Lefty 50s Gretsch guitars are insanely rare, especially in the Duo Jet model!
Humbuckers use two magnets, one which works as a pickup and one which cancels out 60-cycle hum (hence the name humbucker). These pickups generally have a darker voice and a higher output, which allows them to perform better under high levels of distortion. These pickups also tend to sound better playing jazz, as the genre benefits from the darker voice these pickups provide.
Where there is more than one pickup, a switch selects between the outputs of individual pickups or some combination; two-pickup guitars have three-way switches, and three-pickup guitars have five-way switches. Further circuitry sometimes combines pickups in different ways. For instance, phase switching places one pickup out of phase with the other(s), leading to a "honky", "nasal", or "funky" sound[citation needed]. Individual pickups can also have their timbre altered by switches, typically coil tap switches that effectively short-circuit some of a dual-coil pickup's windings[vague] to produce a tone similar to a single-coil pickup (usually done with push-pull volume knobs).
×