For solidbodies there is usually a one- or two-letter prefix indicating the body style or general model. This is followed by a dash and a number which usually indicates the number of pickups (e.g., J-1), although on occasion the number indicates the year of introduction (e.g., TG-54). Guitars bearing a vibrato usually appended an “L” after the pickup number (e.g., MJ-2L).
Chorus is the sound at the beginning of the Guns ‘n’ Roses song Paradise City. It is a gentle, shimmering effect that is good for arpeggiated chords and adding that little extra to a lead tone (such as in the solo for Smells like Teen Spirit by Nirvana). However, we recommend using it sparingly as it can sound dated and old fashioned if over used (unless, of course, old-school is what you’re going for). Common controls include level (the volume of the effect), tone (affects the EQ of the chorus effect), rate (how quickly the note shimmers) and depth (how large and prominent the shimmering is).
I followed with visits to six Los Angeles music stores to play as many guitars as I could (more than 60, including multiple samples of many models), so I could get an idea of what their right-out-of-the-box quality was like and which ones offered the best value. I emerged with a list of the most promising models, and I contacted the manufacturers to request samples. In a couple of cases, I allowed the manufacturers to substitute models that they felt were better suited for this article.
The main purpose of the bridge on a classical guitar is to transfer the vibration from the strings to the soundboard, which vibrates the air inside of the guitar, thereby amplifying the sound produced by the strings. The bridge holds the strings in place on the body. Also, the position of the saddle, usually a strip of bone or plastic that supports the strings off the bridge, determines the distance to the nut (at the top of the fingerboard).
Onboard effects had already appeared on various guitars, especially Höfner and Vox models, but these were not truly “active” in the modern sense. Alembic, with support from the Grateful Dead, was exploring active pickup systems, but these were still basically custom-made instruments. Both had a master volume and tone control with three-way select and a “band rejection filter tone switch,” also called a midrange bypass filter. Ovation was among the first to offer linear potentiometers to correlate movement with effect. Controls inside were mounted on a circuitboard with individual trim pots that can be adjusted to control the volume of each pickup.

{"eVar4":"shop: guitars","eVar5":"shop: guitars: guitar value packages","pageName":"[mf] shop: guitars: guitar value packages: electric guitar value packages: ibanez","reportSuiteIds":"musiciansfriendprod","eVar3":"shop","prop2":"[mf] shop: guitars: guitar value packages","prop1":"[mf] shop: guitars","evar51":"default: united states","prop5":"[mf] shop: guitars: guitar value packages: electric guitar value packages","prop6":"[mf] shop: guitars: guitar value packages: electric guitar value packages","prop3":"[mf] shop: guitars: guitar value packages: electric guitar value packages","prop4":"[mf] shop: guitars: guitar value packages: electric guitar value packages","channel":"[mf] shop","linkInternalFilters":"javascript:,musiciansfriend.com","prop7":"[mf] sub category2"}
Now imagine the puddle again, but this time imagine some wood blocks (12 inch long 2x4's for those of you with rusty imaginations) that are placed on their sides in the puddle in the shape of a three-sided box with the open side facing the pebble's point of impact. The radiating lines go in to the box and bounce back or reflect off the walls. Soon, there are so many lines radiating around in that imaginary box that they all collide with each other and become a random, jumbled mess. Eventually, the size of the lines and the number of them diminish. That my friends is reverb.
I bought my 10 year old son a digitech RP355 multi effects pedal to use. It's cheap and simple to edit patches for different sounds and you can download patches to get the sound used in some popular songs but the thing I like best about it is the amplifier emulation. After using it for a while my son found he liked the sound of Vox amps so we bought a AC4 and it sounds great. I liked the fender deluxe and bassman amps so I had a deluxe amp circuit built by a local amp guy. Later on you will find that you want to move on to real pedals as they sound better so a multieffects pedal is a good way to sample a lot of different effects in one package. Most multi effect pedals have a sampling function so you can record a short song segment and then the unit will replay it while you solo along. Some also have the ability to record from an outside source and then play it back at slower speed so you can learn tricky licks. Lastly, most units have drum tracks which is a great way to play along and stay on time.

Flexibility of the BOSS Katana-50 goes way beyond expectations for establishing a different path referencing to its predecessor the Roland type of practice amps. With 50 watts of power and a custom 12-inch speaker, the Katana-50 can deliver a commanding range of sound playing it clean, crunch, lead, and brown for electric and acoustic electric guitars. Moving on to other controls on the panel, it features customizable effects by using BOSS Tone Studio editor software and for adjusting sounds quickly, it has a dedicated gain, EQ, and effects controls. Tone setting memory is also included for storing and recalling all amp and effect settings.

Description: Body: Mahogany - Top Wood: Maple - Quilted - Neck Attachment: Neck-through - Neck Wood: Maple - Neck Construction: 5 Piece - Fingerboard: Maple - Frets: 24 - Inlay: None - # of Strings: 6 - Scale Length: 27" (69cm) - Headstock: 7 In-Line, Reverse - Bridge: Floyd Rose Style Locking Tremolo - Cutaway: Double - Hardware: Black, 1x Volume Control, 1x Tone Control, Grover Tuners - Circuit Type: Active - Pickups: EMG 707 - Pickup Configuration: H-H - String Instrument Finish: Tribal Purple, Black flame, Tribal Green, Blue Quilt, Satin Natural, Blue Flame


Freshly Realeased from the JVG Vintage Vault..... Just serviced with fresh set up & cosmetic clean up remove grime etc, lube & adjust tuning gears, rehydrate the woods and polish out to the Beauty you see now...detailing & set up here at the JVG shop she's 100% ready NOW and a real rare style beauty too. She's a very clean example of a real Vintage guitar its over 35 years old and is a Japanese Vintage Acoustic guitar. She Plays like butta now! .

I have made over a hundred solid body electric guitars by hand. I can use the same pickup in a plexiglas, or a wood body, utilizing a wood neck, plugged directly into a tube amp, and they do sound different. There is no way anyone can deny me my personal experience on this. I think whats going on here is the new 3D printer body's that are being pushed for their capability of unusual designs. Nothing wrong there, as i have some of my own designs i am going to try as well. I have a contact that makes aluminum guitars, and they also produce a different sound.
The Ibanez GRX20ZBKN is part of the GIO series developed for players who want Ibanez quality in a more affordable package. The guitar is suitable for all types of music, but often a favorite of rock, metal and shred lovers. It features an alder body and a maple neck which feels sleek and fast. Great for moving quickly up and down the neck for those fast riffs and licks. A solid good looking low budget guitar for the beginner and intermediate.
There were at least three different versions of this guitar with differing knobs, fingerboards, control plates, cord mounting, and trim. One even had a nice rosewood fingerboard with dots. This version was the most monochromatic of the bunch, I suppose. It cleaned up really nicely for these pictures. Okay, so it's an ugly little spud. My wife describes this guitar as "so ugly it's cute," and she fell in love with it in the store for that reason. I like that.
I want to combine an LED circuit with the 5 way selector so that it switches LED colors based on the pickup selected. Position 1 = Red, Position 2 = Purple (1+3), Position 3 =Blue, Position 4 = Green (3+5) and Position 5 = Yellow. The questions I have are: 1. The LED circuit has a 9V battery to light the LED. Would this affect the tone of the guitar. 2. I’ve also heard that this might introduce noise in the guitar circuit. Is this even possible?

The way that manufacturers state the wattage output of an amplifier can be confusing. Amplifier manufacturers may state that a combo bass amp produces 600 watts at 4 ohms and 300 watts at 8 ohms. If the speaker mounted in the combo amp is an 8 ohm speaker, then the combo by itself will only produce 300 watts. This combo amplifier will only put out 600 watts if an "extension speaker cabinet" is plugged into the combo amp with a speaker cable. Plugging a second 8 ohm cabinet in parallel wiring with the combo amp's internal 8 ohm speaker will lower the amp's impedance (electrical resistance or "load") to 4 ohms; at this point the amp will put out 600 watts. Another factor that can make it difficult for bassists to select a bass amp is that different manufacturers may state their amps wattage in Root Mean Squared (or "RMS") and in "peak power". For example, a bass amp ad may state that it produces 500 watts RMS and 1000 watts "peak power". The RMS figure is much more important than the peak power wattage.
A plucked string has many modes of vibration which all occur simultaneously; most of these correspond to overtones or harmonics of the fundamental frequency of the vibrating string. Near the center of the string, the fundamental frequency has the largest amplitude; a pickup at 1/4 of the length of the string will be at the point of maximum amplitude of the second harmonic and at a null point for the fourth harmonic. This position gives a strong, full, mellow tone. A pickup at 1/8 of the length of the string (closer to the bridge) will be at the point of maximum amplitude of the third harmonic, and will also get a lot of the fourth and fifth harmonics. This gives a much brighter tone. The change in tone caused by plucking the string close to the neck versus close to the bridge is based on the same idea: bringing out the harmonics in the string in different proportions. See link to a related article, below.
A question which causes much thought and divide! Catch 22 to a degree: you can't play songs till you've learnt some chords, but just knowing some chords will mean you actually can (though you are not aware of it) play loads of songs. There is a plethora of songs out there with only three chords (some with only two!). Their differences are that the order of chords is slightly different for each - with the exception of the thousands of 12-bar tunes!
You're close, but not quite where you want to be with your tone.  You are officially a serious tone chaser; you've already swapped the stock burstbuckers in your awesome R9 Les Paul for something better ... but you are still only at 95-percent of the TONE you want, need, and hear in your head.  Keep seeking grasshopper, and you will find.  For only those who persist will drink from the holy grail.

There is no real rule on what fretsize is best – it is purely personal preference.  To find out what size is right for you or for a specific guitar and application, you may have to try similar guitars with different fretsizes.  I have heard many differing opinions on fretsize over the years; some say tall wire is too bumpy for sliding into position or that tall wire causes them to play sharp (from overly pressing down the strings, these players are used to feeling fingerboard surface under their finger tips).  Some say that fretwire below a certain height is difficult to bend on.  Bending and fretting hand slurring techniques are easier when the string can be addressed towards the middle of the ball end of the fingertip so that it may be pushed and pulled from the side rather than fretted from directly on top by the lower part of the fingertip. Some folks like a low fretwire as it feels very smooth to them and they don’t do a lot of slurring techniques.
Gain – In simple terms, gain is the amount of power your signal is packing. There are a lot of stompboxes that come with gain boosters, which makes it easy to give your volume an instant bump when it’s time for a solo. But be careful of the creep if you add too much gain through too many pedals, or you might end up giving your amp more than it can take, which will throw your distortion out of control.
Control knobs and buttons are typically on the front of the cabinet or chassis, though in some cases, the knobs are on a recessed panel at the back of the top of the amplifier. The most basic amps only have a few knobs, which typically control volume, bass and treble. More expensive amps may have a number of knobs that control pre-amp volume (or "gain"), distortion or overdrive, volume, bass, mid and treble, and reverb. Some older amps (and their re-issued versions) have a knob that controls a vibrato or tremolo effect. The 1/4" input jack is typically mounted on the front of the amplifier. In the simplest, least expensive amplifiers, this 1/4" jack is the only jack on the amplifier.
: I, too, am searching for more info on my Kent. It's a Model 834, violin shaped with a cutaway. Mine is red with "racing stripe" binding on the edge. It's sounds INCREDIBLE (very vintage) and plays well, though I find the neck very narrow. There was an E-Bay auction for a couple of framed ads which featured this model, plus the 833, 835 and 836 from 1967 (one of the pictures, from what I could tell, looked exactly like mine). I also tracked down a picture of one that is a Yellow 67 with a Bigsby-Style vibrato (mine lacks this). If anyone finds a source for more Kent info, I'd love to hear from you...
The E minor chord is one of the simplest to play because you only use two fingers Take extra care not to allow either of them to touch any of the open strings, or the chord won't ring properly. Strum all six strings. In certain situations, it may make sense to reverse your finger position so that your second finger is on the fifth string, and your third finger is on the fourth string.

Not only is Mick funny, but the book is extremely useful for learning theory, efficiency, technique, playing over chords and more. Similar to Creative Guitar (recommended below), Mick is all about having you put in the work to learn what he's laying out. While you'll spend more time learning this way, it'll pay off and at the same time, teach you a great way of learning.


Every ZZ Top tour is a treat for guitar geeks, as Gibbons uses the occasions to unveil a six-string surprise. (Last year it was an elusive Gibson Moderne.) But what really makes Gibbons cool is a certain undefinable quality called “vibe.” Anyone who has ever met Billy and gotten to know him—however briefly—has an outrageous story to tell about the encounter.
Unfortunately, National’s line of instruments was not well diversified and, as demand for the expensive and hard-to-manufacture tri-cone guitars began to slip, the company realized that it would need to produce instruments with a lower production cost if it was going to succeed against rival manufacturers. Dissatisfaction with what John Dopyera felt was mismanagement led him to resign from National in January 1929, and he subsequently formed the Dobro Manufacturing Corporation, later called Dobro Corporation, Ltd, and began to manufacture his own line of resonator-equipped instruments (dobros). Patent infringement disagreements between National and Dobro led to a lawsuit in 1929 with Dobro suing National for $2,000,000 in damages. Problems within National’s management as well as pressure from the deepening Great Depression led to a production slowdown at National, and this ultimately resulted in part of the company’s fractured management structure organizing support for George Beauchamp’s newest project: the development of a fully electric guitar.[5]
This Hellraiser C1 guitar features a mahogany body and a quilted maple top and abalone gothic cross inlays. It looks and feels fantastic! A couple of things that make it sound even better are the locking tuners, that keep it in tune, and the EMG noise-cancelling scheme that makes sure that the only sound the guitar makes is the music you’re playing.

Ibanez are a Japanese guitar brand founded in Nagoya, Japan in 1957. They began by building copies of Fender and Gibson models, but – a couple of lawsuits later – they started creating their own models, which are now icons in their own right. Their line currently includes their famous Roadstar (RG), the thin-bodied S series, and several artist signature models, including guitars for Steve Vai, Joe Satriani, and Mick Thomson.
Modulation is where we step away from the more subtle (relatively) effects which serve to colour an existing tone, and into areas where you can truly begin to add flavour and texture to your tone. There are a few main types of modulation; chorus, phase, tremolo, wah and flange. Chorus subtly mimics your tone with a microscopically detuned duplicate, which when played together adds a nice warm layer to the sound. As an example, play the ‘e’ note on your second string (fifth fret) and the open ‘e’ first string at the same time. Naturally, there is a cent or two difference in the tuning. But you can see that two virtually (but not exactly) instances of the same note makes everything sound a bit bigger and a bit wider. That, in an admittedly basic form, is the chorus effect.
Been in my attic for 20 years...kinda dirty...Rare Vintage Electric Guitar that i have never found an exact pic of on the web...seems like a Teisco Del Rey,but looks earlier than the 60's models ive seen...obviously needs cleaning an repair...but man this thing is cool...a great restoration project...the only marking is the patent number 31-4127 on the truss rod cover...or a Norma or Guyatone version...or just hang it on your wall as a great conversation piece
Instruments with built-in effects include Hammond organs, electronic organs, electronic pianos and digital synthesizers.[19] Built-in effects for keyboard typically include reverb, chorus and, for Hammond organ, vibrato. Many "clonewheel organs” include an overdrive effect. Occasionally, acoustic-electric and electric guitars will have built-in effects, such as a preamp or equalizer.[20][21]
One of the oldest guitar effects, vibrato changes the pitch of the signal at a constant shifting rate. Vibrato adds motion to your tone, but without the “choppy” feel of a tremolo. Vibrato adds a more fluid movement. The slightly detuned, slightly chorus-ey modulation emphasizes bends and makes chords more interesting to the listener. Jimi Hendrix was a visionary user of the Uni-Vibe, which at its core is a vibrato pedal.
Next was Eunice's ‘electric guitar’. It was beautiful and hardly used. However a common problem with guitars of this era were the horrible pickguards made from celluloid that would off-gas while in storage and then wreak havoc over the guitar’s other parts. Upon closer inspection the guitar was actually dripping wet from the many years of storage in the hard case.
For a guitar that sits comfortably in the mid-range segment of the market, Yamaha RevStar RS420 packs a decent punch. Body shape is more reminiscent of a PRS than anything else, but Yamaha definitely infused it with their unique details. The sound is tight, very flexible, and I had no issues dialing in the type of tone I was looking for. A well rounded model, that’s for sure.
The first thing that strikes you about Nate Savage’s Guitar Lessons YouTube Channel is how well the structured, numbered lessons are organised on the YouTube Home page itself. Overlays on the opening titles screens and the names of the lessons make it very clear about the content and help you to choose exactly what you need, or let you skip over any unnecessary stuff. His complete beginner topics go right back to “How To Hold The Guitar” which might sound really basic, but Nate’s absolutely right to nip any bad habits in the bud at the very beginning and that particular video could the most important 3:26 of your career. And I have to make mention of the high production levels on Nate’s videos. The vision and audio is excellent, the lessons are well made, and Nate’s friendly, easy-going manner makes you feel like he’s your best friend and guitar tutor at the same time.
I have been playing guitar, banjo, bass and harmonica for 46 years - and I don't find a $4,300 Martin D 41 to be affordable (Guitar Center price). I play a Taylor 402ce and a dozen other instruments. I believe Taylor is the best instrument for the price..Alvarez Yairi guitars are very good too. Martin and Gibson make fine guitars but they are overpriced. I have a Chinese Maple Guild that sounds fine but the fretwork is amateurish. A Chinese Takamine New Yorker is very well constructed and sounds great.
This is because you won’t have to go through all the hassle of doing research on pickups, then finding a way to mount them without damaging your guitar. While magnetic pickups are surely quite easy to install, contact pickups or blended systems with microphones and preamps might require removing the top, drilling, using all sorts of screws and plates, etc.
Semi-hollow Body Guitars: The first and most classic semi-hollow body is the Gibson ES-335, which was quickly embraced with Chuck Berry and later sonically reinvented by Freddie King, Alvin Lee, Larry Carlton and a host of others in the ’60s and ’70s, who pushed semi-hollow Electric Spanish models into the ’60s and ’70s with aggressive technique and tones.

During the 1930s and 1940s several companies tried to produce a solid-body electric but none of them were commercially successful. Then Leo Fender released his design in 1950 with a single pickup under the name Esquire, then added a second pickup and sold it under the name Broadcaster but soon had to change it due to a lawsuit from Gretsch who were already selling a drum kit using that name. Thus the "Tele" as we know it today was born.

It was also during this time that Perry Bechtel, a well-known banjo player and guitar teacher from Cable Piano in Atlanta, requested that Martin build a guitar with a 15-fret neck-to-body join[citation needed]. Most guitars of the day, with the exception of Gibson’s L-5 archtop jazz guitars, had necks joined at the 12th fret, half the scale length of the string. In keeping with Bechtel’s request, Martin modified the shape of their 12-fret 000-size instrument, lowering the waist and giving the upper bout more acute curves to cause the neck joint to fall at the 14th fret rather than the 12th. Fourteen-fret guitars were designed to be played with a pick and replace banjos in jazz orchestras. Thus, Martin named its first 14-fret, 000-shape guitar the Orchestra Model (OM). Martin applied this term to all 14-fret instruments in its catalogs by the mid- to late-1930s.
Fender-type switches are, obviously, found in Fender guitars but are easily available so could find their way into any guitar, most likely Strat-type guitars. Import-type switches are often found in other makes like Ibanez and on replacement pickguard assemblies. If you have a look at my HSH wiring page and scroll down you’ll see I have an import switch in my Godin SD.
For an experienced guitarist, the choice of amplifier is personal and a major part of the guitarist’s sound. But most of our panelists thought that, for a beginner, it’s most important for an amp to offer a variety of good sounds so that they can find what works for them and make adjustments as their style and taste evolve. As Ken Rosser put it, “If a kid’s starting out and they’re really into Pantera, they’ll love an amp that gives them that sound, but next year they might discover Eric Clapton and want a different sound.”

By 2001, Michael Kelly Guitars added its first acoustic guitars and electric guitars. These collections have evolved and are now sold around the world. To this day, Michael Kelly remains focused on our vision statement to be "Built On Sound" and each time we put the cherry on top by giving the musician a bold look. We are proud that we do not offer the cookie cutter boring guitars that are readily available from so many brands. We know there are players that prefer classic simplicity and we very much respect that. However, Michael Kelly will continue to be the brand of choice for those that prefer something more boutique and unique.
Gibson’s offerings also differ from Fender in that they largely employ scale lengths of 24.75, resulting in a warmer, more rounded out sound that has come to characterize the brand’s output (3). Playability is also affected by the shorter scale length size, with reduced tension making string bending a bit easier. Gibson’s generally utilize mahogany in their construction, which contributes to a darker tone with increased sustain and warmth.
Well, to be more specific, we're talking about Twin Reverbs made between 1965 and 1967. Throughout the decades, these sought-after tone machines have turned up in the rigs of countless guitarists, including Stevie Ray Vaughan—who used a mid-Sixties 85-watt blackface model during his 1985 tour of Japan—Steve Howe, Johnny Marr, Jack White and Dweezil Zappa. The Fender Twin Reverb is considered a standard model for players seeking a clean sound, and it is especially known for the quality of its built-in spring reverb.
I couldn’t find a professional review of the Les Paul Express. The last time we checked, it had earned an average of just 3.8 stars out of 5 in 17 user reviews on Amazon, but most of the complaints I found on Amazon and elsewhere were from people who got samples that weren’t set up well at the factory. This wasn’t true of our sample, but it was true of the other Epiphone sample we received—and it was true of many of the cheap Epiphones I played in stores.
Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Dot - # of Strings: 6 - Scale Length: 25" (64cm) - Headstock: 3+3 - Bridge: Adjustable - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Chrome, 2x Volume Control, 2x Tone Control, 3-Way Switch, Kluson Tuners - Pickups: Harmony - String Instrument Finish: Goldburst, Redburst

Silvertone starter pack is incredibly hard to beat. The candy blue finish gives the guitar a gorgeous aesthetic that looks fully professional. The pickup selector has 5 positions, and there are two tone knobs to give even more control over the sound. Stratocaster fans will love this guitar! Also included in the set is a gig bag, small Silvertone amp, strap, 5 picks, Allan wrenches, strings, a clip-on tuner, and a tremolo bar.
What makes the wah so timeless is its versitility, it can emulate a human voice, be a rhythmic device, boost a screaming lead, a tone shaping tool, among other uses.The first known commercial recording of a wah pedal is Cream’s “Tales of Brave Ulysses”. As we know the distinctive sound caught on with just about every guitar player on the planet! There are too many uses of the wah to mention here, almost 50 years later it is still a must have pedal for every guitarist. For an in-depth look at wah history and a great read please check out “Analog Man’s Guide To Vintage Effects”.

Hi! In this instructable I will be showing you how to fix and/or upgrade guitar electronics. This is applicable to most electric guitars, but I will be using a Fender Stratocaster. It is easier than most people think, especially if you know how to solder. Before you start, find a wiring diagram for your guitar and purchase the parts that are needed.

So many new guitarists, and even not so new guitarists, play with the volume and tone knobs turned all the way up all the time and then shell out lots of money for pedals when they are not satisfied with their tone before taking advantage of what the guitar can do (and it's a lot). Then of course, your amp's tone controls can refine things even more.

This is a good list although after owning most of these brands or at least having played all of them, I would re-rearrange the order. Gibsons although a good guitar are simply no longer the quality of Taylor or Martin. They are lagging behind these guys. Yamaha and Epiphone despite online "reviews" are also not near a Taylor or Martin for that matter. So I would drop Gibson, Yamaha, and Epiphone down the list, and although Seagull makes a decent guitar, they are no better than Blueridge, so I would drop them down and bring Blueridge up. Of course this is all subjective, but here is my list re-ordered for what its worth.


the most with a headphone jack. Any suggestions? I am just a bedroom player who sucks and price is well I say depends what it (the amp) is worthy b/c I am on disability and my neurologist said just quit but at 48 years old it (music) is the only area of life besides my dog and mom that keeps me even and she is in worse shape than me (sorry for the soap box). Is the EVH 5150 III though its' combo is 50 watts but it has the headphone jack. Please anyone help???
X-Series: Back and sides constructed from compressed wood fibers (high-pressure laminate or “HPL“) and solid Sitka spruce or HPL top. Due to this construction these guitars are more environmentally-friendly.[citation needed] Models include: DX1, DX1-R, DXM, DCX1E, DCX1R3, 000CXE Black, and 000X1. Some earlier models used ‘Ebonite’ (black Micarta) fretboards, later models use koa or striped ebony. Necks on all models are constructed from Stratabond, a laminated wood product used for decades in gun stocks and hunting bows. Some of the more recent models are made in Mexico.
Steve Albini, on the other hand, finds it useful to think in terms of blending 'bright' and 'dark' mics. "Normally I'll have two microphones on each cabinet, a dark mic and a bright mic, say a ribbon microphone and a condenser, or two different condensers with different characters." Eddie Kramer's discussion of his Hendrix sessions reveals a similar preference: "Generally speaking, it was either a U67 or a Beyerdynamic M160, or a combination of both, which I still use today. It might be slightly different, of course, but the basic principle's the same — a ribbon and a condenser."
During Michael Laskow's 20-year tenure as an engineer/producer, he worked with Crosby, Stills, Nash and Young, Eric Clapton, Cheap Trick and countless others. He continues to write articles for magazines like Recording and Electronic Musician. He's also the founder of TAXI, an independent A&R company that links record labels with unsigned artists and songwriters.
The output jack is where you plug in your guitar lead. These are generally 1/4″ and transfer the signal created by your pickups to your guitar amp. They are usually connected from a ground wire and input wire. When the lead is plugged into the output jack the signal can be transferred. These can often be a source of trouble and need to be kept tight to reduce noise.

High-end builders of today have gone back to germanium en masse for their classic fuzz tones, and most of them test their transistors to sort out the few that will do the job correctly. They put them in anything from vintage-style units—like Fulltone’s ’69, Frantone’s The Sweet, and Roger Mayer’s Classic Fuzz—to way-out updates of the breed—such as Z.Vex’s Fuzz Factory.
Particularly if you want to get into recording and production, this Blackstar model is ideal. With six distinct “voices” from Clean Warm to OD2, as well as 12 stereo effects, there is a huge range of tones and options to play with. Together with the patented ISF control it allows for a nuanced choice of timbres, allowing you to immerse into exactly the sound you are after in gloriously deep Super Wide Stereo.
very recently I've been trying to get a band together where the Humbuckers of my les paul would suit the sound a lot more and decided to pull out my les paul, on trying to tune it, I noticed the intonation was a little off on all strings (not particularly noticeable by ear, but plugged into a tuner one could see it was off), but on the high E string it was very much off, from the third fret and higher it is very off sounding.
The early Silvertone electric guitars were made by Harmony and Danelectro, with a few exceptions. Danelectro had been making amplifiers since the 1940's for Sears, Epiphone and it's own brand. Their manufacturing facility was in Neptune New Jersey. The Dano's started mainly with the infamous "U" series which had the Lipstick pickups and "Coke-bottle" headstocks. Jimmy Page, Jimi Hendrix and many other rock stars got started and continue to play the Dano's. Aside from the very first Danelectros for Sears they all had the Lipstick pickups. That's how you can tell a Dano from the other manufacturers. Danelectro also manufactured the infamous "amp-in-case" models of which I have two examples: a 1964 and a 1968. If you want more info on Dano's go here.
The best acoustic electric guitars solve the inconveniences of playing a traditional acoustic in a very preferable way. No longer do we need to play a guitar size and shape we don't enjoy in order to project more volume. We don't have to strum and pick harder. We don't need the nuisance of setting up and staying positioned behind a mic to be heard through the loud speakers. Today we look at how this is achieved and share our top recommendations for every budget...
: : Does anyone know for sure where these originated. I have been told Vox (the England years) made this flat bodied plank guitar in the skiffle days of early 60's/late 50's. Mine is painted white(by hand) with a large black pick guard that curves to envelope the two chrome "toaster" pickups ,bottom of neck, and three control knobs.The strings have a moveable maple bridge(not secured) and a small chrome hardtail heel.The neck has a zero fret at top and 19 more playing frets.There are dot inlays at the 3rd,5th,seventh,ninth,12th,and 17th frets.The headstock is of natural finish light maple with a top edge cut at a sloping angle like Hofner.It has brass tuning pegs,gears and gear plates and the keys are white plastic.The beautiful short neck is true ,natural maple.Along one of the tuning gear plates is the numbers: 35515 which are etched into the wood. Four bolts without any plate hold the neck base to the plain body and a green decal above the pegs at top face of headstock reads: Shadow. The fret board is rosewoodand is laid on neck without bindings.It has six strings and sounds like a short scale Baritone guitar. It also only has one strap peg at bottom since they used to put the other end of strap on a tuning key. No other holes are seen for any former peg at other end of body(where normally found). Please send any info on this small,early,simple but awesome sounding electric skiffle guitar from England(Vox?).Thanks!!!!!
Yes, try learning licks before school in a crowded home. Or late at night. Do you want to play or not? Is the simple question. I think I learnt guitar because I could do that all day without bothering anyone. I don't like headphones. Very small amps are OK. But no amp? Yeah. I still do practice scales and stuff unplugged. As a kid I figured out I could brace my guitar against the wardrobe door and it would resonate, great!
Pedaldoc – is a company specialized in the production of kits to convert standard guitar effect pedals into boutique sounding pedal stomp boxes. They carry “do it yourself” kits to modify many topselling Boss pedals, Electro harmonix stompboxes, Vox 847´s wah pedals and more. The only thing needed to perform one of their mods in is about an hour of your time and a soldering iron. Their kits are designed for guitar and bass players who may not have any knowledge of electronics and all the components that need to be substituted are clearly market on a picture of the pcb board of the pedal.

FU was non-stop work & fun at the 2014 NAMM Show in Anaheim California! It was great to be back in the southern California sun with 85 degrees while freezing snow and blizzards were happening back east! The fun started with an opening night party with Eddie Van Halen and the launch of several new EVH Guitar models. The rest is just a blur but here are some out-takes to enjoy, For more behind the scenes photos check out our Facebook page!
Make your next guitar one of a kind. Every luthier set sold by OregonWildWood is visually unique and distinctive - even sets within the same species vary greatly in color, contrast and figuring. You'll find the largest online selection of guitar woods available - all special within their own right. All are exotic, beautiful, unique and superior. Each set is individually pictured giving you the opportunity to choose the perfect one for your next guitar.
Next up is another electric guitar from Fender Standard, namely the American Special Telecaster. This one has two Texas Special Tele pickups and it’s perfect for great American genres like country, rock and blues. This American Special Telecaster has a lovely alder body and the neck is maple. Just like number one on our list, the 50’s Stratocaster, it’s vintage-looking, but the Vintage Blonde model we’re reviewing looks vintage in a cooler, less sentimental way.
When I was a kid in the 60s, all of the Japanese brands (probably ALL made by Teisco) had a really bad rap and only kids ended up with them. Some were very cheaply made, with weak metal, thin chrome plating, funky finishes and thin pickups. I owned a Rodeo, which was terrible. But then, who knew much about guitars then? Nowdays, anything has character.

The Champion 40 is light, affordable, and easy to use. Besides, the brand should give you a clue as to whether or not it’s a good idea to invest your hard-earned money into this alternative. The 12” speaker that it comes with is perfectly capable of rendering both bass and treble, and most guitarists who’ve reviewed it say it works great for blues and country.

I'd never heard of this brand but was recently in a store in North Carolina looking for a nylon string guitar. The salesman asked me if I was "open minded" and if I'd be receptive to trying a brand that I probably had never heard of. He handed me a really pretty instrument with a very different looking headstock. I immediately figured he was showing me a very expensive instrument. I asked how much it cost, but he didn't answer. He simply replied "Try it, then let me know what you think." I had no idea how much this guitar would cost, and honestly I hate guessing games, but the guitar was really beautiful. I played several classical guitars there that day. A Yamaha, a Cordoba and an Alvarez, but the Merida was unquestionably the best sounding (and looking).


In the most commercially available and consumed pop and rock genres, electric guitars tend to dominate their acoustic cousins in both the recording studio and live venues, especially in the "harder" genres such as heavy metal and hard rock. However the acoustic guitar remains a popular choice in country, western and especially bluegrass music, and it is widely used in folk music. Even metal and hard rock guitarists play acoustic guitars for some ballads and for MTV unplugged acoustic performances.
Vacuum tube or "valve" distortion is achieved by "overdriving" the valves in an amplifier.[40] In layperson's terms, overdriving is pushing the tubes beyond their normal rated maximum. Valve amplifiers—particularly those using class-A triodes—tend to produce asymmetric soft clipping that creates both even and odd harmonics. The increase in even harmonics is considered to create "warm"-sounding overdrive effects.[37][41]
For his work on Supernatural, Glenn Kolotkin turned to elaborate multi-miking as a way of managing Carlos Santana's complicated setup. "I used multiple microphones on Carlos' guitars: Electrovoice RE20s close, Neumann U47s further away, an SM56, U87s. He was playing through an assortment of amplifiers at the same time, and by using multiple microphones I was able to get just the right blend."

I've met and talked to Andrew as his shop is 20 minutes from me. When you talk guitars to Andrew, you will get the feeling that this man knows his guitar building. He strives for perfection in his small WV workshop. There is plenty of evidence seeing some of his production models hanging on display. His quiet voice belies his guitar building abilities. As a luthier, his personal hand made guitars command a big price tag. But when you understand how he builds them, you'll understand why. One day, I'll own one his creations from his workshop. But until then, I'll just drool over the pictures. Not sure why his production models are rated at 42 though.
A free, guided tour of the Taylor Guitars factory is given every Monday through Friday at 1 p.m. (excluding holidays). Taylor’s expansive 145,000 square foot manufacturing facility is located east of San Diego (about 20 minutes from the downtown area) in El Cajon, California. No reservations are necessary for the tour, although the company asks that large groups (more than 10) call in advance at (619) 258-1207. Taylor encourages guests to arrive at its Visitor Center, where the tour begins, 10-15 minutes prior to tour time to sign in at the reception desk. The tour lasts approximately one hour and 15 minutes. While not physically demanding, it does include a fair amount of walking.
Looping – These pedals are miniature recorders that capture a passage, which you can then play back as much as you like. Many looper pedals also allow you to layer multiple recordings, and advanced models support extra features like built-in rhythms, mic and other instrument inputs, MIDI, USB and more. It’s worth noting that all the power of a looper pedal does come with a steep learning curve, so be sure that you’re experienced enough to handle one of these bad boys before you bring home one of your own.
I have a almost identical one in front of me, but mine has 3 pickups. It has the same color white guard and sunburst pattern. The back of the guitar has the redish sunburst pattern on the neck like yours but also has the red on the main body, unlike yours that has a colored neck and solid color back. I can’t find a picture of a 3 pickup that is like this. Any info would be nice to know.
The 2019 Gibson Les Paul Standard sports a mahogany back with an artisan-grade AAA figured maple top and a mahogany neck with Ultra-Modern weight relief. This chambering technique is provides a solid core through the center of the guitar, retaining the classic Les Paul sound and making the guitar less prone to feedback. The Ultra Modern weight-relieved body also makes playing long sets a breeze. The neck has an asymmetrical Slim Taper neck profile for increased playability and comfort.
If we've learned anything from this experience, it's that Rocksmith 2014 will do everything it can to try and teach you how to play the guitar, and it's got an amazing array of tools and lessons to do just that. But just like taking lessons from an actual instructor, you have to be willing to put in the time and practice, Practice, PRACTICE, even if it's boring—there are no shortcuts to properly learning your craft. And no matter how many zombies I kill in Rocksmith 2014's Return to Castle Chordead, I'm not really learning chords; instead, I've just learned how to play a video game with a real guitar as the controller.
{ "thumbImageID": "American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Natural/J32625000002000", "defaultDisplayName": "Fender American Elite Precision Bass Maple Fingerboard Electric Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Tobacco Sunburst", "sku": "sku:site51500000006153", "price": "1,999.99", "regularPrice": "1,999.99", "msrpPrice": "2,000.01", "priceVisibility": "1", "skuUrl": "/Fender/American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Tobacco-Sunburst-1500000006153.gc", "skuImageId": "American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Tobacco-Sunburst/J32625000003000", "brandName": "Fender", "stickerDisplayText": "Top Rated", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Tobacco-Sunburst/J32625000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Natural", "sku": "sku:site51500000006152", "price": "1,999.99", "regularPrice": "1,999.99", "msrpPrice": "2,000.01", "priceVisibility": "1", "skuUrl": "/Fender/American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Natural-1500000006152.gc", "skuImageId": "American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Natural/J32625000002000", "brandName": "Fender", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/American-Elite-Precision-Bass-Maple-Fingerboard-Electric-Bass-Natural/J32625000002000-00-60x60.jpg", "imgAlt": "" } ] }

Semi-acoustic guitars have a hollow body (similar in depth to a solid-body guitar) and electronic pickups mounted on the body. They work in a similar way to solid-body electric guitars except that, because the hollow body also vibrates, the pickups convert a combination of string and body vibration into an electrical signal. Whereas chambered guitars are made, like solid-body guitars, from a single block of wood, semi-acoustic and full-hollowbody guitars bodies are made from thin sheets of wood. They do not provide enough acoustic volume for live performance, but they can be used unplugged for quiet practice. Semi-acoustics are noted for being able to provide a sweet, plaintive, or funky tone. They are used in many genres, including blues, funk, sixties pop, and indie rock. They generally have cello-style F-shaped sound holes. These can be blocked off to prevent feedback, as in B. B. King's famous Lucille. Feedback can also be reduced by making them with a solid block in the middle of the soundbox.
• How wear alters playability: Fret wear – grooves worn in the frets from pressing down on the strings, depressions created by bending, lowered overall fret height from usage – can all cause buzzing noises to occur at points where frets are located along the neck. Luckily, these problems can typically be addressed by having the frets leveled and dressed several times before a fret replacement job is necessary, since fret replacements are costly.
Believe it or not, Eddie Van Halen hadn’t even heard rock music until he and his family moved from the Netherlands to Pasadena California in 1967. After hearing Cream, he quickly abandoned piano and drums for the guitar, learning the instrument by picking licks off records by Eric Clapton, Led Zeppelin, Jimi Hendrix and Jeff Beck. These influences were merely a springboard, though. Eddie was quickly able to put his own mark on everything he played.

It’s true that the best guitars are built from the inside out, and Vintage enjoys a well-earned reputation for building great vintage electric guitars. Working with acknowledged guitar industry guru Trevor Wilkinson, Vintage has created a fantastic line-up of Wilkinson-equipped Vintage electric guitars and basses. Using Trev’s excellent range of pickups, tuners and hardware has taken Vintage electrics to the next level.
Samick is a Korean guitar manufacturing company, that is known first for constructing their pianos using imported pieces. The corporation is capable of manufacturing more than one million guitars each year. They have an acoustic guitar with good quality which makes an exceptional sound. The company sell its guitars under its own brands such as Abilene, Silvertone, Greg Bennett, and Samick.

Along with the Dobro name, OMI was acquired by the Gibson Guitar Corporation in 1993. They renamed the company Original Acoustic Instruments and moved production to Nashville. Gibson now uses the name Dobro only for models with the inverted-cone design used originally by the Dobro Manufacturing Company. Gibson also manufactures biscuit-style single-resonator guitars, but it sells them under names such as Hound Dog andEpiphone. The Dobro was first introduced to country music by Roy Acuff.
A right handed 6 strings, electric guitar that mostly comes in black. The body is made from mahogany, while the fret board is made up of rosewood. The fret board is composed of up to 22 frets of 2.7 mm in size. It additionally has beautiful electric features such as a 3 way toggle and a push and pulls volume and tone. Price ranges from INR 21,400-21,541. Click below to get more product details.

Adjusting saddle height couldn’t be easier on a Les Paul. Since the bridge can only be adjusted at each end, there is no need to adjust each saddle individually. Firstly check and, if necessary, adjust the low (thick) E string height. Do this by adjusting the height of the bridge at the thick E string end. This is done by rotating the thumbwheel anti-clockwise (counter-clockwise) to raise the bridge or clockwise to lower it. You might be able to do this with just your fingers, but chances are you will need to use pliers. Be careful if you use a tool as it is easy to slip and damage the finish on your guitar. Alternatively you can slacken all of the strings and use your fingers, although this is a very time-consuming process. Finger method

Remember when I said that there were 2 amps widely used as practice amps and tools for guitar tech’s? Well, the Orange Micro Crush Mini Guitar Amplifier Combo is the other one. Warm ups before gigs, during set ups and maintenance work, this amplifier is relied upon to provide accurate sound and incredible tone anywhere, anytime. This is one of the best cheap amps available thanks to the fact it’s made by one of the most respected amplifier manufacturers in the world, powered via 9V battery and busts out some seriously amazing clean and dirty sounds.


One of the most important things when choosing your guitar is of course the sound - read the study on electric guitar sounds. It’s best if you’re able to try different guitars out in a music shop, and the staff there will most likely be happy to present you with different options that are good for beginners. There you will also have the chance to see how the different guitars feel to play, and have the opportunity to ask the staff if you have any questions or need any advice.

Eddie's Guitars specializes in the finest electric guitars available today. We have spent many years seeking out the best builders, brands and models available from yesterday and today. From classics like Fender Custom Shop and Gibson Custom Shop to boutique builders like Collings, PRS, Tom Anderson, Grosh and John Suhr we have every avenue of the sonic world of guitar covered.

The GrandMeister Deluxe refines the German firm's best-selling compact head, with four flexible channels and a host of built-in effects. Just about everything is MIDI-powered, so you can edit and store presets to your heart's content. The rear panel includes the latest Red Box recording output, and there's also a new improved iPad app that you can use to edit and store presets, either at the end of a lead or using a wireless MIDI adaptor. The GrandMeister Deluxe 40's four channels sound quite different from those of its predecessor: they're more balanced, with slightly less treble emphasis and a smoother but no less powerful bass response. There's plenty of headroom on the clean channel, which dovetails seamlessly with the higher-gain crunch channel. Both clean and crunch are very tweed-influenced, dominated by a warm midrange that's equally flattering to humbuckers and single coils, especially when boosted and laced with a little of the GrandMeister's digital reverb, which can be combined to taste with delay, chorus, flanger, phaser or tremolo. The two American-voiced lead channels have all the gain you could possibly need for almost any musical genre, from classic rock to modern drop-tuned metal, with a nicely sculpted top-end that squeals and snarls on demand. As a do-it-all tool the GrandMeister 40 takes some beating. All of its many features work efficiently and it's hard to point the finger at shortcomings, because there really aren't any.


This pedal has been a great start, it has been looked after very well and is in excellent condition. I am upgrading my sound which is the reason for the sale. “Great guitarists know it's all about nuance. With its built-in expression pedal, the Zoom G1Xon allows you to add subtlety and refinement to your performance. Add in 100 great-sounding guitar effects and amp models—with the ability to use ...
I disagree about Martin being THE BEST ACOUSTIC GUITAR. While Martin is an excellent guitar that is definitely ONE of the best! Taylor is THE BEST FOR THE HIGHER END TO MID PRICE RANGE! A decent TAYLOR will bea Taylor will beat the brakes off a brakes off the same Martin, because they SOUND BETTER and they can be used for more than one or two styles. If you are playing county music the Martin is better, but Taylor will play a lot better sound way better on every other kind of music styl! Buy a TAYLOR
The S2 Custom 24 features a mahogany body with book-matched flame maple top, that follows the same double cutaway shape and detailed arch as the original Custom 24. The guitar's mahogany neck is also not far off, being rafted from mahogany with PRS' distinctive 25" scale length. It has a 24-fret rosewood fingerboard that has a comfortably narrow nutwidth of 1.656". Finally, the S2 Custom 24 owes its voice to its dual humbucker pickups that include the S2 Vintage Bass and the S2 HFS Treble - which provide PRS' characteristically open and clear tone. You can push or pull the tone knob for single-coil tones should you need them.
On Martin guitars, this is a really big deal. Martins all seem to have a problem with the "neck set" on many of their guitars before 1970. High string action is the result, making the guitar very difficult to play. This can only be fixed correctly by a "neck set" (removing the neck on the guitar, and refitting the neck at a slightly increased angle, which lowers the string action). If done correctly, this does not affect the value of the guitar (and in fact can make it more valuable, as the guitar is much more playable). Generally speaking, most players would agree if the "string action" is more than 3/16 inch (5 mm) at the 12th fret, the guitar needs a neck set. This measurement is taken from the bottom of the low-E string, to the top of the 12th fret.

Before we wade in, please note that National Dobro and subsequently Valco, more than most other manufacturers, were notorious for putting together guitars with parts left around. This, combined with the fact that they routinely used components (especially bodies) provided by other manufacturers, means that you are likely to find instruments with details inconsistent with catalog descriptions, and they may just be Kosher.
Most pickup selectors are either mounted to the top of the guitar through a cavity routed in the back of the body or mounted to a pickguard. For pickup selectors that are mounted to the top of the body, simply take a screwdriver and unscrew the pickup selector. You will have to remove the knob on the end of the level before you can slide the selector through the channel and out of the cavity. For pickguard mounted selector, like Fender Stratocasters, you will need to remove the entire pickguard to remove the selector. Simply unscrew the pickguard from the body, flip it over, and rest it on the top of the body. The pickguard will still be wired to the body, so you can’t go very far with it. Then, unscrew the selector. It is important that you take note of what wires are soldered to what lugs before you remove the selector. If you are not familiar with electric guitar wiring, I suggest that you draw a picture of the selector and label the soldered wires. Once you know where everything has be wired, you can cut the wires close to the lugs and remove the old selector.
too many to the point their incredibly over rated for me personally, there's a world outside of Gibson that cost a fracton as much and will blow peoples heads off. I have a custom 7 string I bought off craigslist someone made that's worth about 500 dollars because I didnt pay for some name on the headstock and so on. All my friends from blues and jazz lovers to metal would rather play my guitar. more frets for soloing than their les pauls active pickups a Floyd rose locking tuners 4 big reasons right there
If you’re making the crossover from electric to acoustic, then Takamine won’t be a particularly well known brand to you, but rest assured that they’re a top make when it comes to acoustics, and of course electric acoustics. The GN93CE-NAT is a mid-range electric acoustic that features some really nice touches, such as the rosewood fretboard, and is an interesting choice.

Six full steps (one octave) down from standard tuning. The Low E has the same fundamental frequency as a bass guitar, essentially the same standard tuning as a bass guitar but with a high B and E added to mimic a regular guitar. This tuning is used on the Fender Bass VI and similar instruments. Notably used by John Lennon with The Beatles, Robert Smith of The Cure and Jack Bruce of Cream. In his early days with Ronnie Hawkins, future Band bassist Rick Danko was also seen with a Fender Bass VI. This is the tuning Earth used on their seminal drone doom album, Earth 2. Also used in some Doom Metal and Sludge Metal bands such as Thou.
Guitar amp and FX plug-ins are very advanced nowadays to the point that you can actually record “clean” by plugging your guitar straight into a mixer or interface, and add a plugin like Guitar Rig, Amplitube or Waves GTR as an insert. You will hear this effect as you play but without any risk of feedback, since no mics are live in the room. This approach also means you can tweak and change any aspect of the sound post-recording since the raw recording is actually completely dry.
In the image above, the first higher peak we see is E4 (i.e. the low E-string on a guitar in standard tuning), the second peak is E5 (i.e. an octave higher) and the following high peaks are B5, E6, G#6, B6, D7, and so on. Remember that the test rigs only have two strings, both tuned to E, and plucked open. So what you are hearing is a mish-mash of tons of overtones that shape the character of the “tone” that you hear.
1. striking the string creates the vibration and once it disrupts the magnetic field on the pickup that's it - how about when you don't strike the string at all, like when you tap on the body of the guitar? The vibrating wood imparts vibration on the strings, which in turn do their thing on the pickup. The body of the guitar, the nut, the bridge, every part of the guitar is now directly influencing the sound you hear out of the pickup. Remember, only the magnetic field disturbance is being amplified, and tapping the guitar has started the strings vibrating. How can that happen without the wood's tonal qualities affecting the waveform?
Overstock SaleNew ProductsVacuum TubesSpeakersAccessoriesAmplifier PartsBooks & DVDsCapacitor Amplifier SetsCapacitorsCoversEffect Pedals & PartsEnclosuresFootswitch BoxesGift CertificateGrill Cloth, Tolex & PipingGuitar PartsHardwareJacks & PlugsKeyboard PartsKitsKnobsLuthier ToolsMaintenance ProductsPMT Tone ModsPotentiometersPower AccessoriesRadio & Antique Equipment PartsResistorsReverb TanksSemiconductorsSpeakersSwitchesT-shirts/GiftsTech SuppliesTerminal Boards & StripsTransformers & ChokesVacuum Tube AccessoriesVacuum Tube Amplifier SetsVacuum TubesYellow JacketsZero Glide Nuts
This is a FREE service from NoBSGuitar.com. Credit card NOT required. You can unsubscribe at ANY time 24/7. We value your privacy. We will NEVER rent, sell, or give away your email address to anyone for any reason, ever. By signing up, you agree to receive emails from nobsguitar.com, including full guitar lessons, newsletter #1 on the next page, and occasionally, product recommendations we feel are worth your time.
The Vintage Modified Jazzmaster has the tried-and-tested dual circuitry of the original models from the ’60s. The “Rhythm” circuit activates only the neck pickup, while the “Lead” circuit lets you pick between neck, bridge and both at the same time. Each circuit has its own dedicated master volume and tone knobs. (In comparison, the Fender American Professional Jazzmasters don’t have this circuitry.)
PPS: Made from Polyphenlene Sulfide a material commonly used in automobile and computer parts the PPS picks are lightweight but hard enough to ensure picking is strong and precise, so the pick provides accurate attack with a full-bodied tone as it strikes thestring. Silicon rubber based surfacing on each side, makes this pick ideal for fast picking styles. Available in Teardrop and Jazz shapes, and 0.8mm-1.0mm-1.2mm gauges.

“The tremolo tail assembly was engineered specifically for the Spectrum ‘5.’ The bridge is an integral part of the whole assembly and is, of course, universally adjustable. The marvel of it all, however, is that the tremolo does not exert any friction (hence no wear and tear) on the strings. The tremolo action causes the whole bridge assembly to move smoothly back and forth.


This is the brand of guitars manufactured by a Japanese company and are available in India. The company creates incredible custom – shop instruments and high-quality original designs, liked by some of the best professionals on the planet. They produce electric guitars that provide high performance and are long-lasting in terms of duration and quality. E-10 is one of the most popular guitars of this brand. The starting price of ESP electric guitar is 16,000 INR approximately.
A combination of standard 7-string tuning and an 8th string dropped one full step. Allows to play in the range of a standard electric bass, as well as power chords. Used by Animals as Leaders[47] and Whitechapel (on the songs "Devolver" and "Breeding Violence" from A New Era of Corruption). Also used by Deftones on Koi No Yokan and Gore, Allegaeon, and Emmure on the song "N.I.A. (News in Arizona)". A variation of this tuining is used by Hacktivist with 3rd and 4th strings tuned a whole step up to A and E respectively.
It features a handsome Grand Auditorium shape with a soft cutaway for good access to the higher frets, while the satin-finished sapele neck is incredibly playable – as is the case with all Taylor guitars. The iconic brand keeps costs low with laminated sapele back and sides paired with solid Sitka spruce on the top, as well as producing it in the respected Mexican facility.
Wiring: If you chose the optional snap together wiring, then all of our instruments come pre-wired and pre-soldered, so that you can assemble the instrument without needing to do any soldering. You simply snap a few connectors together to complete the electrical connections before you screw down the pickguard, control panel, and output jack plate. This is detailed on the guitar kit wiring and hole drilling description page. If you would prefer to not have your kit pre-wired and pre-soldered, please let us know.

How it sounds: Ex. 1a demonstrates the treble-cut control—nothing surprising here. Ex. 1b features the bass-cut. With a clean tone like this, it’s a bit subtle, though you can hear the difference if you focus on the low notes. But Ex. 1c adds a vintage-style germanium Fuzz Face with the gain and volume maxed. With the guitar’s tone control wide-open, the signal easily overpowers my vintage Fender brownface—your typical Fuzz Face fart. As I gradually trim bass via the guitar, the tone acquires greater punch and clarity. I remain on the neck pickup throughout—the only thing changing is the guitar’s bass pot setting. The extreme-cut settings near the end of the clip may sound harsh in isolation, but they can be perfect in a band context. At the end of the clip I max the bass pot again to underscore how much the tone has changed. It ain’t subtle.


Larry Robinson Fine Custom Inlays - They produce one-of a kind shell inlays for all kinds of guitars. One of a handful of inlay practicioners in the country, Larry has done exquisite work for major guitar manufacturers (Fender, gi bson, Yamaha,...), small production shops (Santa Cruz, Collings, etc.), single luthier shops (Klein, Ryan, Olson, Megas, and more), collectors like Tsumura and people who just want something to personalize their guitar.
MXR’s Distortion+ preceded the Tube Screamer and is an even simpler design, and, despite its name, is more an overdrive than a distortion. That said, its sound is considered by many to be a little more opaque, or colored, than the Tube Screamer’s. The box uses a 741-type IC and a pair of germanium diodes to achieve its soft-clipping sound. These are different components than the famed germanium transistors, but are made of the same material. Germanium is generally attributed a “softness” of tone, and the same applies to the diodes used in the Distortion+ (and other units); change them for silicon diodes and you’ve got a hard-clipping distortion pedal.
Oh but this guitar is beautiful. The PRS SE A50E Angelus is something you would really want to play in front of an audience because of its stunningly good looks and the quality sound it produces. This guitar has a solid Sitka spruce top, figured maple back and sides, mahogany neck, bone nut and saddle as well as ebony fretboard and bridge. It has a distinct and highly playable Angelus Cutaway body shape. The PRS abalone bird inlays on the fretboard are a really nice touch. Yes, it’s a gorgeous, well-built guitar, but that’s not all.
: I have a similar guitar to the one you bought. It was my grandmothers and I'm estimating it at over 30 years old. Very folk style. She told me she actually had the original strings from when she bought it! I believed her when i tuned the thing and the day after found that the 4th and 6th had snapped. From what i know, Decca just made guitars around that time, 60's to 70's. Mine says it has a steel reinforced neck and it is really heavy compared to others. its still in really good shape and I actually play it. I'm not planning on selling it but I know its well worth its age. It has a hand chissled Ser. # on the bridge.
With two decades of experience and thousands of local customers served I found myself unemployed/downsized in 2010 asking myself what I wanted to do next. After some searching I understood that I really enjoy the interaction that takes place in the local store between the customer and the shopkeeper. I know that we can offer the same prices as the big stores and hopefully make the experience more enjoyable.
The book discusses both tabs and notation which makes it easier to transition if you’ve been using the former. It covers a wide range of topics including scales and arpeggios. The approach the author takes is logically and accessible with plenty of examples and exercises to make it stick. The only downside is that there are no songs included in it.
In the Guitar Setup course, the third DVD is devoted to acoustic guitar setup. Acoustics are very, very different than electric guitars, when you get right down into the mechanics of them, and as such they truly do need a section of their own in any guitar setup guide. You’ll learn how to setup the action and intonation properly on your acoustic, as well as many other tips and tricks that will help you keep it in top working order.

Having got the technicalities out of the way, it's time to look at recording methods. The traditional method, and still the most satisfactory in many cases, is to mic up a really good amplifier, but where this isn't appropriate, we have a choice of physical modelling guitar preamplifiers, complete guitar/pickup/amp modelling systems using Roland's VG series of products, or the slightly lower-tech approach of using analogue guitar recording preamps (solid state or valve). The latest option is to plug the guitar directly into the computer and use a software plug-in to handle the amp and speaker modelling, but I'll start at the beginning with the miking options.
Rolling Stones best electric guitarist list should've been nicknamed the best average guitarist list. I didn't give this guy the time of day because I thought the bucket thing was to cover up how badly he sucks. Turns out it's the opposite. He's just weird. It's too bad the average person doesn't have the capacity to enjoy this type of advanced music.
Basic guitar chords are built using the first, third, and fifth tones of the scale that corresponds with the chord you want to play. For instance, if you want to play a G major chord, you go to the G major scale and find the first, third, and fifth notes in the scale. The G major scale has one sharp (F), so the notes in the scale are G-A-B-C-D-E-F#. The first note is G, the third note is a B, and the fifth note is D. These are the notes you need to make a G major chord. If you wanted a G minor chord all you need to do is make the third note a flat. This system applies to any chord you want to build. These three note chords are called triads and make up the bulk of the beginner open positions chords you’ll use to play a lot of guitar chords songs. When you study these chord shapes, you’ll notice that the root of the note (the first note) usually appears on the lower string and is doubled on a higher string, which reinforces the key tonality.
The models in this list of best acoustic guitars have their own visual charm that appeals to different people. For example, the Blueridge BR-160 has those ornate inlays on the headstock. Some guitarists love those kinds of design elements, while others may find them a bit over the top and would much rather prefer the fretboard inlays on the PRS Angelus, or the simple but classic cutaway design of the Taylor 110ce.
The implementation of musical chords on guitars depends on the tuning. Since standard tuning is most commonly used, expositions of guitar chords emphasize the implementation of musical chords on guitars with standard tuning. The implementation of chords using particular tunings is a defining part of the literature on guitar chords, which is omitted in the abstract musical-theory of chords for all instruments.
Recent amplifiers may include digital technology similar to effects pedals, up to the ability to model or emulate a variety of classic amplifiers. Some modeling systems also emulate the tonal characteristics of different speaker configurations, cabinets, and microphones. Nearly all amp and speaker cabinet modeling is done digitally, using computer techniques (e.g., Digital Signal Processing or DSP circuitry and software).
×