Solid state systems grew in popularity in the 80s and 90s, as the digitization of audio signals posed a more reliable and less expensive alternative to tube amplification. In recent years, however, many guitarists have been willing to fork over a little extra scratch to get their hands and their ears on the sounds of the past, on the warm tones that the computers can't seem to capture.
One unique application of a fuzz pedal involves starving the pedal of voltage--which will produce a scratchy, velcro-like tone. This is desirable by some musicians because it is a highly unique sound and is often employed by more avant garde musicians. This sound can be achieved by purchasing a power supply with a sag output, or using a nearly dead battery, although the pedal won't last long when using that method.
Across the United States, there are increasing concerns from businesses about the supply of science, technology, engineering, and mathematics trained workers. Although science and math test scores in the US are among the lowest around the world, the US educational system is in the process of revitalizing the “hands on” learning techniques as a way to enhance the participation and success of students. Our project meets the needs of applied learning with the flexibility of being modular in the classroom.
yeah i know the GSP has 2 EQ ( well 3 if i wanted to use up a slot in the OD section ) but i use both EQs on the GSP and i prefer a external eq, that i can adjust on the spot depending on that patch, rather then going in and changing the EQ each time on that patch. I use 3 different guitars each one is totally different in sound, so the external EQ really helps.
Players who want to emphasize low volume and portability — especially the ability to discreetly pack their amp — will want to look for as small a unit as possible. Some of these can still create a decent sound, but you’ll find that their natural overdrive is going to sound considerably compressed, and there won’t be much dynamism in response to your picking or strumming pattern.
Their LP models have a "mahogany" body, and the binding is very thin so I think the maple top is just vaneer. I also noticed the headstocks were not the usual LP angle. In my opinion, Epiphone wins hand down. The Strat types don't look much better in my opinion, again, sharp fret ends and awful looking headstock and logo. If you see any of their relic jobs, you'll notice that they range from passable from a distance to hideous from any range.
So just to throw this out there- I've been trying to figure out how to set up electric guitars on my own for years and could never get it remotely figured out. At about 11:30 pm last night I decided to take a garbage fret buzzing machine of a guitar and try again. Your blog is the first time I've comprehended and successfully set up a guitar!! I'd buy you a six pack if you were in the neighborhood!
A batch of 20 to 30 guitars featuring Ripley’s electronics was assembled using Japanese bodies and necks. The one in our possession is a GS2-R (#28949) with a standard (no German carve) Strat-style body, bolt-on multilaminate neck made up of red-dyed 1/16″ maple strips glued end-to-end, pointy-droopy carved bi-level six-in-line headstock, Gotoh tuners, black hardware, 24-fret ebanol fingerboard, faux-pearl pennant inlays and locking Ovation Floyd-Rose-licensed vibrato system. Two plastic-covered humbucking pickups (no exposed poles) featured individual output controls for each string, with six individual three-way mini-toggles for selecting pickups combined with six fader pots directing string/pickup output to a stereo jack.
This can all get a little tricky and can become overwhelming especially if you have never tackled this type of job before. If this is the case, I strongly suggest starting with one of the easier models in regards to wiring e.g. Telecasters are significantly easier to work on as the scratchplate will often be pre-loaded with pickups. However, if you purchase a kit guitar such as an LP or you want to upgrade your electrical components (which is often the case with an entry level kit) understanding some basics about guitar electronics is useful.
Great Martin Copy from the later 60's This example is a Well Crafted in Japan model with the "orange lable" Nippon Gakki highly collectable now as a great player Martin like player. Great wood...just see the pics WoW! Sitka Soruce Top, Premium AAA Grade Mahogany neck - sides & back...Made by serious craftsmen high degree of skill and well balanced. Nice big Tone as a Martin same type X bracing and is a proven performer. Nicely aged wood and is a wonderful playing 7 sounding vintage guitar equal to many more expensive builders like Martin. This one has a slight stable old top crack as glued and is not an issue anymore...Plays like butta...You will love the sound! .

Another great practice amp in the running for best electric guitar amp for beginners is the Blackstar HT Series HT-1. It’s a 1W tube amp with a single 8″ speaker. It features 2 channels (clean and overdrive), stereo MP3 / line input and external speaker output. It’s use of dual-triode ECC82 tubes provides the crunch and break-up characteristics of a traditional 100w amp at a much lower volume. It also has EQ, Gain and Reverb settings.
In 1966, Teisco guitars shed some of its adolescent awkwardness of the early ’60s in favor of a svelter, hipper look. While some of the tubby bodies and monkey grips remained, they were joined by leaner shapes, thin, pointed, flared cutaways and German carve contours. In many ways, the ’66 Teisco line is the quintessential year for Teisco, which is fitting since it would be the last under the original ownership.
The Effect:Reverb pedals have remained a staple pick in each guitarist’s arsenal in order to provide that extra sound refinement and enhancement when necessary. It may be tricky, learning to apply the right amount of Reverb, as too little may go unnoticed, and too much may sound silly, yet finding that sweet spot is definitely thrilling and satisfying. Great option for every beginner (or a so called must have guitar pedal) is the Boss FRV-1 63 Fender Reverb Pedal. If you want to dig deeper into the reverb effects, check out our dedicated article, the plethora of reverb pedals for you to choose from will surprise you.

#### This guitar features two MP-90 pickups that can be switched on at the same time to produce sweet yet aggressive sounds. This guitar is mainly used to play country and indie music. This guitar has a radius of 9.5’’ and 22 medium jumbo frets for comfort and speed of play. It has a six saddle hard-tail bridge that allows precise settings and ease of adjusting string heights. The fingerboard is maple finished which makes for fast play. This guitar features three finishes sunburst, black transparent and vintage white.

A good guitar builder can pick materials that provide a predictable result. The process of making a guitar that costs $10,000 and one that costs$1,000 is identical, or at least very similar. The big difference is likely that in the more expensive one, personal attention has been put into selecting, drying, storing, and cutting the tonewood. The cheaper, which is mass produced by less skilled labor, consists of the same species of wood, but from a pile that came out of a container, in the order it was stacked. This means that two guitars from the same batch can sound quite different. They can sound exactly like the expensive guitar, but they can also sound different.
Guitar pedals, sometimes called effects pedals, provide an easy and effective way to modulate your electric guitar's tone. The order of your pedals well ensure the best tone, but what tone that is depends on your personal preference. While there are basic guidelines, there's really no right or wrong way to order your pedals. To set up guitar pedals, learn the basic guidelines and experiment to find the arrangement that best creates the style and tone you want in your music.[1]
Go to iOS Ram List  Both the above sets convert your device or PC to the equivalent of a high-end sound module for your midi keyboard.  It has the full 15-velocity-layered version of the Yamaha C5 Grand (592mb) along with lots of other sounds. This set also includes extra string sounds that are in the Nice-Strings-PlusOrchestra set (all except the harp).
Artists all over the world are enjoying the classic looks and premium features of Vintage Guitars. Professional players and producers working with world renown Artists like Gregg Allman, Amy Grant, Josh Turner, and many  more, rely on the great sound and playability of Vintage Guitars. See what they’re saying about the guitars they’re rocking out on every night!
Power chords are one of the staples of rock music and one of the most important guitar chord types you need to have in your toolbox. They are important to learn for a few reasons: They’re easy to play They’re used a TON in many popular songs and are very versatile. They’ll help broaden your repertoire of guitar sounds / styles. This post will walk you through step-by-step what a power chord is, how to play them and what songs you can learn to start practicing them. What are Power Chords? Whether you play an acoustic or electric guitar, you are going
The Super Chromonica 270 Deluxe is an updated improvement on the Super Chromonica, featuring tighter reedplate fixtures, thicker reedplates, round holes in its chrome-plated mouthpiece, a smoother slide mechanism which can be remounted for left-handed use, and a round-edged comb for more comfortable holding.[36] The Deluxe is also available with a gold-plated mouthpiece and coverplates, known as the Super Chromonica Gold.[37]

Squier Affinity Stratocaster has all the same features of the Fender Stratocaster guitar at a highly affordable price. It has a maple neck and an alder body which gives it a snappy Strat tone. It also has three single-coil pickups that can be manipulated by a 5-way switch. A vintage style tremolo system makes it a great choice for those who like that system.
The best thing about the guitar is the design and usability is perfect for the beginners, who have an idea that how to play the guitar. It also comes with a bunch of instructions that makes it even easier to use. Once you learn the basics and master it you can easily upgrade to a higher level guitar. It can give the right feel that required from a guitar.
But alongside Davy Graham and Jim Hall, the other musician I really wanted to remind you about was Martin Taylor. Astonishing technique – enough to make the shredders weep with envy, coupled with an exquisite feel for melodic line. Martin is one of the few guys (or gals) whose playing brings tears to my eyes regularly. When one of his albums gets into my CD player it stays there for weeks. In many ways, a natural successor to Django Reinhardt, truly a master of music as well as the guitar art and DR’s principal competitor for a top ten place in my list.
{ "name": "Brown", "skuUrl":"/accessories/el-dorado-vintage-hand-tooled-leather-guitar-strap/361014000008000", "status": "instock", "statusText": "In stock", "pimStatus": "R1", "inventoryText": "In Stock & Ready To Ship", "inventoryKey": "in_stock", "price": 155.00, "formatedIntegerValue": "155", "decimalValue": "00", "isOnSale": false, "msrp": 155.00, "salePrice": 155.00, "listPrice": 155.00, "isPriceDrop": false, "priceDropPrice": "", "savingPercent": "0.00", "promos":["freeShipping","topRated","flexibleFinancing","guarantee","international"], "warranty": false, "freeWarrantyAvail": false, "sku": "site1sku361014000008000", "displaySku": "361014 000008000", "serialized": false, "stickerDisplayText":"Top Rated", "shipsFree":true, "condition": "New", "priceVisibility": "1", "scene7SetID": "MMGS7/361014000008000_MEDIA_SET", "invMsgVendorDropShip":"false", "invMsgOverSized":"false", "invMsgBackOrdered":"false", "invMsgPreOrder":"false", "invMsgPromiseDate":"", "invMsgAvailability":"", "invMsgDetail":"", "invMsgAddOnText":"", "currencySymbol": "$", "styleImgUrl": "https://media.musiciansfriend.com/is/image/MMGS7/Vintage-Hand-Tooled-Leather-Guitar-Strap-Brown/361014000008000-00-140x140.jpg", "styleImgAlt": "Vintage Hand-Tooled Leather Guitar Strap Brown", "freeGiftWarning":false, "freeGiftWarningTips":"", "isShipsInternational": true, "pdpLoyaltyPoints":"1,240", "pdpLoyaltyPointsMultiplier":"1.0", "checksum":"82996536150", "restrictionType":"", "restrictionError":"" } The company’s reputation and output continued to grow. Forays into mandolinmaking in the late 1890s and ukulele making in the 1920s greatly contributed to their expansion, and by 1928 they were making over 5000 instruments per year. The company remained family-owned and employed a relatively small number of highly trained craftsmen making instruments primarily by hand. By the early 1960s Martin guitars were back-ordered by as much as three years due to limited production capacity. In 1964, Martin opened a new plant that is still the primary Martin production facility. Acoustic guitars that have been fitted with a pickup can be recorded using the same techniques as standard electric guitars when plugged into an amp. Interesting sounds can be created by mic’ing up an acoustic guitar and sending the sound through an amp. This can be done live – although you should be aware of feedback – or a previously recorded acoustic track can be re-amped and used exclusively, or mixed with the original acoustic track. You can get some really gnarly and original ‘electric’ sounds with creative use of overdriven acoustic guitar; it’s especially good for slide playing. The RP360 XP lets you combine different effects to craft your preferred sound by choosing from its wide variety of options including 74 effects, 32 amp models and 18 cabinet models. Each setup can be saved into one of its 99 user presets, that allow for incredible flexibility. The interface has a bit of a learning curve, but allows for deep editing.  This may seem like an odd value to consider, but most guitarists need to feel a certain connection to their instrument. It’s part of what makes being a guitarist different from other types of musicians; a sense of individuality as well as style. Your guitar will be a significant investment regardless of which brand you settle on, and while sound and construction are more critical factors overall, it’s important that your instrument inspires you. Different brands are known for cultivating different images; Gibson’s and Fender’s were made famous by the rock gods of yesterday, while Taylor’s unique acoustic bodies will conjure up a different vibe for a folk player. Again, this aspect speaks to your individual needs as a guitarist. {"eVar4":"shop: guitars","pageName":"[gc] shop: guitars: agile","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: guitars","prop1":"[gc] shop: guitars","evar51":"default: united states","prop10":"brands","prop11":"martin","prop5":"[gc] shop: guitars","prop6":"[gc] shop: guitars","prop3":"[gc] shop: guitars","prop4":"[gc] shop: guitars","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"} There are many, many variations of the electric guitar. Science has told us that in order for sound to be naturally amplified, there needs to be a chamber in which sound can resonate. Just look at the construction of the ancient amphitheaters, or the way that the human body has natural resonating chambers that allow us to use our voices, or a stand up bass, with its large, chambered body designed to amplify the resonating strings. Usually what a lot of people complain about when they say a small amp has a lack of power, they mean that the lower tones feel a little lacking. Well, picking the right amp, and placing it right, should allow the lead guitar to shine with the high tones, while also being powerful with the low tones. Yes a smaller amp will; forever have issues with low tone, but correct construction, presence of vacuum tubes, and even simply the correct placement can all solve these problems during small gigs. Depending on your choice of guitar kit you may be required to perform a small amount (or a large amount) of work wiring the guitar. This typically involves a soldering iron and a basic understanding of guitar electronics. You will also need to be able to follow schematic diagrams of pickup configurations. It’s not a one size fits all job either, wiring up a Telecaster is different to wiring a Stratocaster and a Les Paul or hollow body is different again. DRILLING THE NECK HOLES ON THE BODY Before you do this you can carve down the back of the neck area if that is something you were going to do. If you are just going to leave it flat then that's ok too. The first step if you are using furreles is to map out where you want to place them and then mark the center of the hole where the screw will go. Then take your forstner bit drill enough to fit the furrele inside. Usually you can tell how deep to go if you drill a little at a time, and place the furrele in it to see if it is just low enough in the hole not to see the top of it if you look at the body horizontally or it is flush with the wood. After doing this you can drill the holes for the screws. Use a bit that has the same circumference as the screw including the threading so when you put the scre into the hole it just passes through with out you having to screw it in. Drill in the indention that was left by the tip of the Forstner bit, keeping the drill as straight as possible. {"eVar4":"shop: books sheet music and media","pageName":"[gc] shop: books sheet music and media","reportSuiteIds":"guitarcenterprod","eVar3":"shop","prop2":"[gc] shop: books sheet music and media","prop1":"[gc] shop: books sheet music and media","evar51":"default: united states","prop10":"category","prop11":"books, sheet music & media","prop5":"[gc] shop: books sheet music and media","prop6":"[gc] shop: books sheet music and media","prop3":"[gc] shop: books sheet music and media","prop4":"[gc] shop: books sheet music and media","channel":"[gc] shop","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] category"} Description: Body: Koa - Flamed - Neck Wood: Maple - Neck Construction: U-Shape - Nut Width: 43mm - Fingerboard: Rosewood - Binding: White Sparkle - Frets: 22, Jumbo, Medium - Inlay: Thumbnail - # of Strings: 6 - Scale Length: 24.6" (62.5cm) - Headstock: 3+3 - Bridge: Rocking Bar - Bridge Construction: Ebony - Cutaway: Single - Hardware: Grover Romantics Tuners, 3x Volume Control, 1x Tone Control, 3-Way Switch - Pickups: FilterTron - Pickup Configuration: H-H - String Instrument Finish: Flamed Koa Here we have another very Beautiful and rare "The Aria Model" Vintage Japanese F style Mandolin with such amazing tone!!! nearing 40 years old these are AMAZING! This is the rare " The Aria" Model M700 as seen on the Classic inlay in the headstocks Gorgeous Brazilian Rosewood veneer is a super beautiful Japanese example of the highly revered F style mandolin made famous by Gibson. These older models were put out during the 1970s this example was 1973. These premium examples have become so popular with Players & Collectors over the past several years now. The inlays on the neck and headstock and the classic violin sunburst on this model are simply gorgeous! The top is solid tight grained old growth Sitka spruce and the back & sides are premium AAA figured & flamed maple, the neck is Mahogany This particular M 700 is in very good condition with some minimal wear from playing please refer to the pics for those details. The original case and pick guard are also still present and do come with this fine instrument the guard is simply off for now. With the resurgence in popularity of Bluegrass and other music styles utilizing the wonderful Mandolin sound in recordings and live performances these rare Gibson Replicas vintage mandolins have been steadily increasing in popularity and in value because players are catching onto the great old high end vintage Japanese instruments now so the demand has risen accordingly. If you're looking for a great Vintage Mandolin that is extremely well made with top craftsmanship utilizing top the grade AAA woods that have now aged and have a wonderful vintage patina to them these are the affordable Japanese vintage F Mandolin alternative choice to a$5000.00 - $10,000 vintage Gibson F-5 ..thats why many Pros today are seeking the best vintage for a great deal. This Old Aria M700 is simply a great one!. Thats a major bend of opinions! It all boils down to..the style of music that you play and what you expect out of the guitar! Is playing only a hobby or are you trying to make a living bangin that Ax? The price of a guitar is not as important as the ability of the person strumming the strings! If your abilitys suck,and you have a expensive guitar..You Still Suck..No matter how good the guitar may be! I have owned cheep and expensive guitars of all different brand names..some very good..some very bad..bottom line is..if Your happy with the AX,thats all that matters! Screw the Name or the Price!! Alvarez has always been an under-rated brand. Beautiful workmanship, great sound- an excellent value for the money. I have one of the old six string "dove" guitars and a Yairi 12 string: both are close to forty years old and both still sound and look great and have never needed any repairs. I also have an old Martin six string. I have done the "blindfold" test with friends to choose the best sound between the alvarez and the martin - alvarez wins every time. The Tube Screamer pedal has a long list of iconic users including Stevie Ray Vaughn, Gary Moore, John Mayer, Joe Bonamassa, The Edge and many more. As such, it is only expected for a company like Ibanez to take advantage of its popularity to extend their reach in the amplifier market - resulting in the creation of the Tube Screamer Amp (TSA) series. The Ibanez TSA15H leads the series in terms of ratings, with its compact yet versatile head profile while having the same combination of tube amplification and built-in tube screamer circuitry. At its core are two 12AX7 preamp tubes and two 6V6 power amp tubes, a standard configuration that sounds good on its own. Its standout feature is the implementation of a Tube Screamer circuit, which comes complete with the same controls as the iconic green pedal it is based on. Smaller-scale instruments are produced to assist children in learning the instrument as the smaller scale leads to the frets being closer together, making it easier for smaller hands. The scale-size for the smaller guitars is usually in the range 484–578 mm (19.1–22.8 in), with an instrument length of 785–915 mm (30.9–36.0 in). Full-size instruments are sometimes referred to as 4/4, while the smaller sizes are 3/4, 1/2 or 1/4. The following open-tunings use a minor third, and give a minor chord with open strings. To avoid the relatively cumbersome designation "open D minor", "open C minor", such tunings are sometimes called "cross-note tunings". The term also expresses the fact that, compared to Major chord open tunings, by fretting the lowered string at the first fret, it is possible to produce a major chord very easily.[14] Being part of Schecter's upper tier guitar line, this one comes packed with premium appointments, including a nice looking arched quilt maple top that follows the double cutaway shape of the mahogany body. It also has a 3-piece set mahogany neck that can withstand angry riff playing while the ultra access heel allows for easier upper fret access when you want to hit your audience with high note solos. The guitar has a Sustainiac Humbucker on the neck (known for long sustained notes) and the high output EMG 81 Active Humbucker that's great for metal riffs. Other features include Floyd Rose 1000 Series Tremolo, 25.5" scale length and 1.625" nut width.  It is definitely an opinion based list, ask 100 people, and get 100 different answers. But please, 99 out of those100 would have Clapton on it, the list loses credibility without him. Pictures of “Clapton is God” tags around England stick in my mind. Even among his peers he is revered, he just has to be here! Page should be higher, but of course, that’s just my “opinion”. The output transistors of solid state amplifiers can be passively cooled by using metal fins called heat sinks to radiate away the heat. For high-wattage amplifiers, a fan is often used to move air across internal heatsinks.[14] Since transistor bass amplifiers used for large venues need to produce a high output, this usually means that bass amplifiers are very heavy. Most powerful transistorized bass amplifiers use class AB or so-called "push-pull" topology, in no small part because this output circuit scheme can be physically lighter and cooler than an equivalent Class A amplifier. These need heavy transformers and require large metal heat sinks for cooling. Description: Body Construction: Solid - Neck Attachment: Bolt - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 22 - Inlay: Dot - # of Strings: 6 - Scale Length: 24.75" (63cm) - Headstock: 3+3 - Bridge: Tremolo - Bridge Construction: Rosewood - Cutaway: Double - Hardware: Chrome, Diecast, 1x Volume Control, 1x Tone Control, 5-Way Switch - Pickups: Humbucker - Pickup Configuration: H-S-H - String Instrument Finish: White, Black, Red, Sunburst What would happen if four former Marshall employees got together? Well in this particular case, they formed Blackstar! Their product range includes hand-wired amps (the Artisan series) as well as products featuring different digital technologies (the ID:series). Plus, we have them to thank for the existence of the ISF system, a control that allows to switch gradually between American and British sound. In spite of the company's young life (it was founded in 2004), the brand already has many artists associated to its name like Silenoz (Dimmu Borgir) and James Dean Bradfield (Manic Street Preachers). Unlike most new wave guitarists at the dawn of the Eighties, Honeyman-Scott had impeccable fashion sense. He always maintained a timeless detached rocker look, and his aviator shades, medium-length shag haircut, suit jacket and jeans attire never really went out of style, unlike the geometric haircuts and DayGlo suits that many of his contemporaries wore. He always played the coolest guitars onstage as well, from classic Gibson Les Pauls and Firebirds to custom-made Hamers and Zemaitis metal-front guitars. i have an old Dorado solid-body electric serial # 0726454 on the neck plate it says STEEL ADJUSTABLE NECK, then the serial number, then made in japan. it has abalone fret markers, and dorado is in abalone in the headstock, blonde finish white-black-white-black pickguard, and a funky trem. i was told once that maybe guild had made this guitar... seems pretty unlikely... and that it retains it's original value, it all seems pretty unlikely... but i don't know... please help!!!  In the early 1960s Rickenbacker history became forever wedded to one of the biggest music upheavals of the 20th century: the invasion of the mop-top Beatles from Liverpool, England. The Beatles used several Rickenbacker models in the early years. Before the group broke up, John Lennon would own at least four. This love affair began in Hamburg, Germany in 1960 when he bought a natural-blonde Model 325 with a Kauffman vibrato. Lennon played the original (which was eventually refinished black but still easily identified by its gold-backed lucite pickguard) on all Beatle recordings and in all concerts until early 1964. Rule 1—There are no rules. The sound you’re after might not be made by what we could call the appropriate or logical signal path, but that’s not always the issue. The issue is this: what does it sound like? If it makes the sound you’re after, then it’s right…although, you may have to do something about the noise. Traditional pedal board arrangements were designed for certain reasons, and keeping the noise down is one biggie. Following the principles of how sound is made in physical space is another (see Rule 4 coming up). But the final choice is yours. As a very wise man said: if it works, don’t fix it. In May 1965 Keith Richards used a Gibson Maestro FZ-1 Fuzz-Tone to record "(I Can't Get No) Satisfaction".[24] The song's success greatly boosted sales of the device, and all available stock sold out by the end of 1965.[25] Other early fuzzboxes include the Mosrite FuzzRITE and Arbiter Group Fuzz Face used by Jimi Hendrix,[26] the Electro-Harmonix Big Muff Pi used by Hendrix and Carlos Santana,[27] and the Vox Tone Bender used by Paul McCartney to play fuzz bass on "Think for Yourself" and other Beatles recordings.[28] We would suggest that you don’t check price tags too much when choosing your guitar. If you try a few out in a music shop you can ask them to suggest a few different guitars within your price range and then try them out only thinking about sound, looks and feeling. This way you won’t be fooled by a cheap price tag to think that a guitar can’t be any good, or the opposite, be tricked into thinking that just because a guitar is expensive it has got to be the best. Small-diaphragm condenser mics, on the other hand, tend to have flatter frequency plots and a better-behaved off-axis response, giving a sound sometimes described as more focused, but they seem to be less commonly chosen by the interviewees than large-diaphragm ones. Neumann's KM84 seems to be the most regular choice of small-diaphragm condenser, and numbers John Fry and Bill Price amongst its high-profile users, while Sennheiser's MKH40 warrants a particular mention from Mike Hedges: "I started using [these mics] when I was working with the Beautiful South. I started off with two and now have more than 20. I think they were originally designed for classical recording, because they have very high gain and very low noise. This means that you can get a very clean sound. They also accept massive amounts of volume, so you can put one against a guitar amp on full and it will take it." Hedge's concern about the ability of the microphone to handle the sheer volume of some guitar amps is echoed by several of the other producers, who make a point of mentioning that they switch in a condenser's 10dB pad when recording electric guitars. South Korea has been one of the largest OEM guitar factories in the world since 1980's. Nonetheless, the words "Made in Korea" still invoke visions of low cost alternatives to high-end manufacturers. At Swing, our mission is to lay these stereotypes to rest, and show the world that we can produce true professional grade instruments, made by professionals, for professionals. (Of course, company is not a patriotic organization. This is a matter of manufacturer's pride and self-satisfaction that can be called "Professionalism".) It is to note that each of these metal strings is made to vibrate at a particular rate. The amount of electrical charge produced by the vibrating motion in the pickup coils is then sent to an electric circuit, consisting of resistors and capacitors, which controls the tone and amplitude of the electric signal. The electric signal is then sent to an amplifier which is electrically connected to the magnetic pickups. Promotion lasts for 1 year from date of purchase. After that period, your voucher is redeemable for the amount you paid, less any value you may have received. Not valid as payment for Eat24 purchases. Not valid with other vouchers, certificates, or offers. Only 1 voucher(s) can be purchased and redeemed per person. Cannot be purchased as a gift. Subject to the General Terms. Learn more View more { "thumbImageID": "StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Cruz-Teal/L20238000003000", "defaultDisplayName": "Ernie Ball Music Man StingRay5 Special HH Ebony Fingerboard Electric Bass", "styleThumbWidth": "60", "styleThumbHeight": "60", "styleOptions": [ { "name": "Cruz Teal", "sku": "sku:site51500000222146", "price": "2,299.00", "regularPrice": "2,299.00", "msrpPrice": "2,300.00", "priceVisibility": "1", "skuUrl": "/Ernie-Ball-Music-Man/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Cruz-Teal-1500000222146.gc", "skuImageId": "StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Cruz-Teal/L20238000003000", "brandName": "Ernie Ball Music Man", "stickerDisplayText": "Preorder", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Cruz-Teal/L20238000003000-00-60x60.jpg", "imgAlt": "" } , { "name": "Aqua Sparkle", "sku": "sku:site51500000222145", "price": "2,299.00", "regularPrice": "2,299.00", "msrpPrice": "2,300.00", "priceVisibility": "1", "skuUrl": "/Ernie-Ball-Music-Man/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Aqua-Sparkle-1500000222145.gc", "skuImageId": "StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Aqua-Sparkle/L20238000004000", "brandName": "Ernie Ball Music Man", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Aqua-Sparkle/L20238000004000-00-60x60.jpg", "imgAlt": "" } , { "name": "Jet Black", "sku": "sku:site51500000222144", "price": "2,299.00", "regularPrice": "2,299.00", "msrpPrice": "2,300.00", "priceVisibility": "1", "skuUrl": "/Ernie-Ball-Music-Man/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Jet-Black-1500000222144.gc", "skuImageId": "StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Jet-Black/L20238000002000", "brandName": "Ernie Ball Music Man", "stickerDisplayText": "", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Jet-Black/L20238000002000-00-60x60.jpg", "imgAlt": "" } , { "name": "Charcoal Sparkle", "sku": "sku:site51500000216758", "price": "2,299.00", "regularPrice": "2,299.00", "msrpPrice": "2,299.02", "priceVisibility": "1", "skuUrl": "/Ernie-Ball-Music-Man/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Charcoal-Sparkle-1500000216758.gc", "skuImageId": "StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Charcoal-Sparkle/L20238000001000", "brandName": "Ernie Ball Music Man", "stickerDisplayText": "Top Seller", "stickerClass": "", "condition": "New", "priceDropPrice":"", "wasPrice": "", "priceDrop": "", "placeholder": "https://static.guitarcenter.com/img/cmn/c.gif", "assetPath": "https://media.guitarcenter.com/is/image/MMGS7/StingRay5-Special-HH-Ebony-Fingerboard-Electric-Bass-Charcoal-Sparkle/L20238000001000-00-60x60.jpg", "imgAlt": "" } ] } The Korg Kaoss Pad is a small touchpad MIDI controller, sampler, and effects processor for audio and musical instruments, made by Korg. The Kaoss Pad's touchpad can be used to control its internal effects engine, which can be applied to a line-in signal or to samples recorded from the line-in. Effects types include pitch shifting, distortion, filtering, wah-wah, tremolo, flanging, delay, reverberation, auto-panning, gating, phasing, and ring modulation. The Kaoss Pad can also be used as a MIDI controller. Mijn first guitar was a Epiphone by gibson sg, it was all right, then I got my gibson sg special(Around 550e), really good guitar, huge difference with the Epiphone. My next was, believe it or not another Epiphone, a Casino limited edition with bigsby, best price/quiality guitar ever(I paid 430e), beautiful guitar, and next week I’m getting a Fender Telecaster American vintage 58′(1755e), I’m very excited about it. I also own a Fender jazz bass classic 70s, it’s a mexican which plays like an american, very proud of this bass. First rate guitars are normally the best, you pay for the quality of the materials and the workmanship and experience, but there are exceptions with second range guitars, you can get very good ones, just good models or plainly good guitars, it’s nice to own both kind of guitars. ### It wouldn't be called a tribute if it didn't follow convention, so having a mahogany body with an arched maple top is expected. Epiphone also designed the neck to mimic the playability of old LPs, giving this guitar a 1960s SlimTaper D profile. However, what makes the Epiphone Les Paul Tribute Plus stand out is the use of two Gibson USA '57 Classic humbucking pickups, which essentially gives this Les Paul a more premium Gibson voice, at a fraction of the price. If you are trying to find the best electric guitar for beginners but you lack the time to do the necessary research in order to find a quality product, this short introduction should help you out. After reading plenty of electric guitar reviews and after comparing top-notch products, we have reached the conclusion that Epiphone Les Paul STANDARD is the model that you should have in mind. This device has a beautiful mahogany body and a maple top that is said to deliver an easy to distinguish classic tone. As a plus, the model comes outfitted with Alnico Classic humbucker pickups that secure a subtle and warm tone. If the Epiphone Les Paul STANDARD is out of stock, we recommend that you check out the Epiphone Les Paul STANDARD Electric as it is a reliable alternative that you might equally enjoy. The basic sound of the amplified electric bass or double bass can be modified by electronic bass effects. Since the bass typically plays an accompaniment, beat keeping role as a rhythm section instrument in many styles of music, preamplifiers ("preamps"), compression, limiters, and equalization (modifying the bass and treble frequencies) are the most widely used effect units for bass. The types of pedals commonly used for electric guitar (distortion, phaser, flanger, etc.) are less commonly used for bass, at least in bands or styles where the bassist mainly plays a rhythm section role. In styles of music where the bass is also used as a soloing instrument (certain genres of heavy metal, progressive rock and jazz fusion), bassists may use a wider range of effects units. Jazz fusion bassists who play fretless bass may use chorus effect and reverb for their solos. What equally contributes to the Entourage’s place on our list of the best acoustic-electric guitars is its nuanced and bright acoustic sound. This signature tone comes courtesy of a select pressure-test solid cedar top and wild cherry back and sides. The electronics on this model are easy to use and compact, highlighted by a pewter plate giving the entire package a stylish appearance.​ Although the hollow bodies of these guitars create a mellow, naturally voiced tone perfect for jazz, vintage country and other styles that require warmth and clarity, they can also snarl. For proof of the latter, check out Lennon’s performances on “Revolution” and “Cold Turkey.” Too much volume or proximity to the amplifier, however, and hollow bodies can howl with feedback unintentionally. And that’s why the semi-hollow body guitar was invented. Frets are the metal strips (usually nickel alloy or stainless steel) embedded along the fingerboard and placed at points that divide the length of string mathematically. The strings' vibrating length is determined when the strings are pressed down behind the frets. Each fret produces a different pitch and each pitch spaced a half-step apart on the 12 tone scale. The ratio of the widths of two consecutive frets is the twelfth root of two ( {\displaystyle {\sqrt[{12}]{2}}} ), whose numeric value is about 1.059463. The twelfth fret divides the string in two exact halves and the 24th fret (if present) divides the string in half yet again. Every twelve frets represents one octave. This arrangement of frets results in equal tempered tuning.  One detail is the rating, honestly there is no right or wrong here really, it's down to personal preferences. A .022uF capacitor will roll off less treble frequencies than a .047uF, so you'd perhaps notice a more prominent drop in treble when rolling a tone pot down which has a .047uF cap wired to it than you would if it was a .022uF. This to me is an important detail to consider when choosing the right cap for you, but if you're still not sure, the general rule is .022uF for humbuckers and perhaps P90s, and a .047uF is used primarily for single coils. This isn't set in stone though, so perhaps consult your pickup manufacturers recommendations first. If you want any help in choosing the right rating for your harness though, I'm very much here to help, so by all means drop me a message! I'll second the neck comment, conditionally. My first guitar was a hand-me-down Monterey archtop acoustic that had been my uncle's, and it have a sharp V neck. Out of nostalgia I bought another Monterey on eBay and its cross section feels like a tomato can lying in my hand. After a refret it plays smoother and easier than anything that fat has a right to. The original frets..., not quite.  For our purposes, I’ll break pedals down into four overarching categories: 1) Boost, Compression, Distortion, and Fuzz; 2) Modulation; 3) Echo and Delay; and 4) Filtering and EQ-Based effects, and this series will focus on individual types that come within each of those larger categories (for example, Modulation includes many quite different effects, such as chorus, vibrato, phasing, and so on). This is not to say that some manufacturers or other writers couldn’t categorize things differently, and certainly a few examples below could be safely lifted out of the heading I have stuck them in and accurately described by another category. It doesn’t matter all that much. These headings are mainly a means of breaking down the sonic results of the enormously varied range of pedals that exists out there, and taking a brief look at what makes them tick. Good looks and playability seem to be the two biggest selling points of the Ibanez AEG10II. Many describe it as a fun instrument, thanks to its comfortably thin profile body and fast action setup. A good portion of its positive reviews are from users who after gigging with the guitar, have great things to say about its reliability and amplified sound. Because of the miniaturization of all things electronic, you can now get full-sounding, authentic guitar sounds from a unit the size of a disposable camera — as long as you listen to it through headphones (meaning that it has no speaker or power amp of its own). These battery-powered wonders come with belt clips for untethered practicing (great for checking your stage moves in the mirror). Our 4 yr old grandson picked this guitar out and we purchased it for him as his Christmas present, he absolutely loves it. His dad has been teaching him to play it and he said that you can actually plug the guitar into his amp instead of the one that came with it. Our grandson will most certainly grow into this guitar and will get many hours of playtime with this guitar. The Viper came in two versions made of ash, maple, alder or mahogany, the 1271, with two single-coil pickups, and the 1273 Viper III with three single-coils. Vipers had two-octave unbound fingerboards of either rosewood with pearl dot inlays or maple with black dots. A laminated pickguard (with model name engraved) held the pickups and extended down the body for the controls, including master volume and tone knobs. The plastic-and-metal bridge/tailpiece assemblies were the same as on the early Preacher. The single-coil pickups were about the size of mini-humbuckers with metal sides, black inserts, and flat polepieces. Windings were different depending on the position. The bridge pickup had poles slanted diagonally that emulated the slant of a Strat. Early Vipers have a three-way toggle. As with the Preacher, later Vipers have no name engraving, the all-metal bridge assembly, and an extra toggle which is probably a series/parallel switch.  Shreddage 2: Absolute Electric Guitar is our answer to the challenge of total guitar sampling. It is a complete instrument with elegant scripting, intuitive mapping, and incredible depth. This virtual guitar for Kontakt is the ultimate weapon for rock & metal music, built from the ground up for realistic playing in any hi-gain style. All samples were recorded on a 7-string guitar and are provided clean/DI so you can use your own custom amp tone - or use the included Peavey ReValver HPse. Due to the good critical response received, the ATH-M50x can be considered the flagship of Audio-Technica headphones, and it definitely doesn’t disappoint. It’s clearly a professional product, so much so in fact that philistines who dare compare it to models directed at casual entertainment get verbal beat downs in comment sections from its many fans. Gruhn Guitars: If you're looking for a convenient appraisal that can be done online--something along the lines of what May Music Studio used to do--Gruhn Guitars offers an appraisal service. You must first send information and pictures of your guitar according to their guidelines. You must also include a payment for the appraisal fee, which varies depending on the instrument. For metal there are few better performers than this menacing guitar from Schecter; the signature model of Avenged Sevenfolds lead guitarist Synyster Gates. From the pinstripe double-cutaway mahogany body emerges a hugely-playable thin C-shaped mahogany set neck with ebony fretboard, 24 extra-jumbo frets, and Schecters Ultra-Access construction to allow unhindered access to the highest of frets. Two solidstate Tempo beginner amps were offered in ’71. These had black tolex covers, front-mounted controls and a rectangular logo with block letters on the grille. The Tempo No. 158 ($65) had an 8″ speaker, 10 watts of power, tremolo with speed control, reverb with depth control, three inputs, volume, tone and a black grillcloth surrounded by white beading. The Tempo No. 136 ($31.50) offered a 6″ speaker, six watts, three inputs, volume and tone. The grillcloth was dark (probably black) with horizontal flecks.  It is an obvious fact that all those great guitarists must have had a humble beginning, having started with the best beginner guitar that suits them. Some of these artists started with guitars inherited from their parent, friends and/or relatives while others ordered theirs from guitar shops. If you are a newbie yet a guitar enthusiast and you are seeking to buy one among the best guitars for beginners, then there are tips and facts you will have to put into consideration. Bassists pairing an amplifier "head" of a certain wattage and a speaker cabinet (or speaker cabinets) with a certain wattage power-handling capacity may require advice from music store amplifier expert or an audio engineer. One of the reasons that many beginning bassists choose combo amps when they are starting is because with a combo amp, the manufacturer has ensured that the speaker and power amp are compatible from a power handling and impedance perspective. While there is a widespread belief that an amplifier with a rated wattage that is higher than the rated wattage on a speaker cabinet will harm the speaker, in fact, a clean, un-clipped power amplifier signal can be above the rated wattage of a speaker without damaging the speaker, as long as the power amp is sending out a clean, unclipped signal. There is a much higher risk of damaging a speaker when a clipped (unintentionally distorted) power amplifier signal is sent through it, even if the wattage is far below the rated wattage of a speaker. For example, a bassist could use a 700 watt power amp which is running with zero power amp clipping through a speaker cabinet rated at 500 watts without damaging the speaker; however, if a 100 watt power amp that is heavily clipping is plugged into the speaker cab, this could blow the speaker. Possibly the most famous of all guitar effects, the talk box has its indelible place in history. The guitar signal is pushed thru a speaker into a tube that the player holds in their mouth. This tube is usually run up a mic stand, so that the player can use the embouchure of the mouth cavity to control vowel sounds that are then picked up by the microphone and pushed back through the PA system. This diagram shows 3 single coils wired in parallel, allowing seven tone choices. The typical 3 single coil guitar contains a 5 way rotary switch which allows you to get 5 sounds - each single coil; neck and middle in parallel and middle and bridge in parallel. This modification will give you 2 more sounds - all 3 pickups in parallel and Neck and Bridge in parallel. The Jameson Left-Handed Black is an acoustic-electric guitar that comes with a slick appearance, a smooth body, and an impressive sound. With its thinline frame and cutaway design, this model is good for both amateurs and seasoned guitar players. You get a guitar that sounds just as awesome regardless if you’re playing it unplugged or through an amp.  Description: Body: Maple - Body Construction: Semi-Hollow (Chambered) - Top Wood: Spruce - Neck Wood: Maple - Fingerboard: Rosewood - Frets: 20 - Inlay: Block - # of Strings: 6 - Scale Length: 24" (61cm) - Headstock: 3+3 - Bridge: Adjustable - Bridge Construction: Rosewood - Cutaway: Single - Hardware: Chrome, 2x Volume Control, 2x Tone Control, 3-Way Switch, Kluson Tuners - Pickups: Harmony - String Instrument Finish: Natural The original National and Dobro companies produced the most popular and most imitated acoustic Hawaiian guitars ever made, and Valco was no slouch when it came to their electric successors. Indeed, lap steels are among the most highly regarded of Valco’s products, regardless of the brand name on the headstock. The more affordable steels still command a respectable price considering their ubiquity, and the higher-end models usually match the equivalent Fenders and Gibsons in appraisal. This is particularly true of the National Grand Console, one of the staple steels of the 1950s. Single coil pickups are the simplest to wire because they typically have only two leads – hot and ground. Some humbuckers have their coils connected internally and are pretty much the same to wire as single coil pickups. That’s why we will call them both “two conductor pickups”. Ground leads are typically connected to a common grounding point and hot leads are switched in and out of the circuit. Let’s take a look at standard Strat-style switch. Granite, when quarried in its natural state, also has a crystalline atomic structure which is ideal for sonic transference and has a compression strength of 19,000 psi, and a tension strength of 700 psi—the material these blocks are made of is the fourth densest on earth next to Diamond, Carbon and Quartz that has ideal resonant qualities which will decrease signal loss from your guitar to your amplifier by at least 30%. Utilizing this optimum material allows you to achieve maximum attack, clarity, sustain, note articulation, note separation, harmonics and punch. While the lows get tight and articulate, the harmonics scream effortlessly! Palm mutes, tapping, sweeps, you name it, all sounds so much better. Bass effects are electronic effects units that are designed for use with the low pitches created by an electric bass or for an upright bass used with a bass amp or PA system. Two examples of bass effects are fuzz bass and bass chorus. Some bass amplifiers have built-in effects, such as overdrive or chorus. Upright bassists in jazz, folk, blues and similar genres may use a bass preamplifier, a small electronic device that matches the impedance between the piezoelectric pickup and the amp or PA system. Bass preamps also allow for the gain of the signal to be boosted or cut. Some models also offer equalization controls, a compressor, and a DI box connection. NO BRIAN MAY?? The guy built his OWN guitar. He sometimes added piano wire behind the guitar strings, he was technical and had soul, and is an innovator. I personally find East Bay Ray from the Dead Kennedy's marvelous. I know he doesn't belong in this list, but any musician that has their own sound like these two deserves a mention……but yes, taste is subjective anyway. I first met Ralph Novak in 1980, when he was working at Subway Guitars in Berkeley, California. I'd assembled a kit Strat and it needed a refret. My monstrosity was painted Shell Pink in tribute to Strats from Fender's surf era. Little did I know what was to come of Ralph's distant future. He was the fret guru in Berkeley, and his work was astounding - the best I'd ever seen! Ironically, Vintage Guitar columnist Stephen White was also working at Subway at the time. So began our journey into luthiery madness! Fast forward to 1989. {"reportSuiteIds":"guitarcenterprod","pageName":"[gc] services:repairs","prop2":"[gc] services:repairs","prop1":"[gc] services","prop5":"[gc] services:repairs","prop6":"[gc] services:repairs","prop3":"[gc] services:repairs","evar51":"default: united states","prop4":"[gc] services:repairs","channel":"[gc] services","linkInternalFilters":"javascript:,guitarcenter.com","prop7":"[gc] services"} custom made guitars luthier services alvarez ampeg benedetto boss breedlove collings danelectro ,dean,digitech eastman electro-harmonix ,grinning elk, electro-harmonix epiphone fender- fender-custom-shop fender-usa fulltone g&l gibson godin gretsch guild hagstrom hal-leonard hamer harmony heritage hofner ibanez jackson kay line-6 marshall martin mxr national orange ovation paul-reed-smith peavey prs prs-paul-reed-smith rickenbacker roland silvertone suhr takamine taylor vox washburn yamaha 000-18 00-18 4001 asat-classic catalog champ classic custom-22 custom-24 d-18 d-28 d-35 deluxe es-125 es-175 es-335 flying-v j-45 j-50 jaguar jazz-bass jazzmaster l-00 lap-steel legacy les-paul- les-paul-classic les-paul-custom les-paul-deluxe les-paul-jr les-paul-junior les-paul-special les-paul-standard les-paul-studio lg-1 lg-2 melody-maker mustang precision- precision-bass sg sg-special sg-standard strat,bass guitar,speakers,parts,effects pedals stratocaster- telecaster telecaster-custom telecaster-deluxe telecaster-thinline..Greg's Guitars is the only author of "The Vintage Guitar News and Views. The Squier Deluxe Stratocaster by Fender is another excellent electronic guitar for newbies. The body is made up of basswood which is a soft, light wood with some of the best mid and upper frequency production. A maple neck and fretboard further assists the mid and high range frequency sound. Its C-shaped neck guarantees the best comfort. This guitar features three single coil pickups. One is assigned for master volume control, one tone control for the neck pickup and one tone control for medium pickup. The five-way switch lets you combine these three pickups and produce the widest range of sounds ever!  Am I missing something? Few MIDI artists can document the finest details of legato expressed by some human performers, but such nuance is within the scope of current notational languages. If no human can or will produce such detailed documentation of existing performances, computational machines can, if not now, soon -- unless the inexorable march toward AI that can pass the Turing test is more exorable that it might appear. "Mangoré, por Amor al Arte" is the title of the 2015 movie, the real life story of Agustín Barrios, an influential and important composer and classical guitarist from Paraguay. Born in Paraguay in 1885 talented Agustín was persuaded in his young adult age to move to Buenos Aires, the cultural hub of South America. In Argentina he began an affair with the beautiful Isabel but,... The Kay Musical Instrument Company grew from the Groeschel Mandolin Company (or Groeshl Instrument Company[8]) in Chicago, established in 1890.[9] In 1921, the company was renamed to Stromberg-Voisinet. In 1923, later president Henry Kay "Hank" Kuhrmeyer joined the company, and in 1928, with the help of an investor,[9] he bought the company and started producing electric guitars and amplifiers.[10] Many people "re-amp" direct guitar tracks recorded to a DAW using amp-modeling software, with good results. Plug-ins are wonderfully suited to the virtual recording environment, allowing for fast access to a plethora of modeling amplifier and speaker cabinet combinations, hence tones, effectively replacing a roomful of amps, cabs and microphones. Programming the virtual amplifier is the same as tweaking the knobs on the real thing, and the same is true for programming software dynamics and effects processors in relation to their hardware equivalents. As the realism and sophistication of modeling technology continue to develop, so does the viability of virtual re-amping as a production technique. Stripped holes: small holes without much tension on them (i.e. pickguard screws) can be repaired with super glue (gel stuff). Put some glue in the hole and screw the screw in about 1/2 way. The glue will not stick to the plated screw, and will form threads. More severely stripped holes or holes w/ more tension on them (i.e. strap button screws) require pieces of toothpick be glued in w/ wood glue. Larger holes w/ alot of tension (i.e. neck mounting screws) require the hole be drilled out and a hardwood dowel glued in place. Many people "re-amp" direct guitar tracks recorded to a DAW using amp-modeling software, with good results. Plug-ins are wonderfully suited to the virtual recording environment, allowing for fast access to a plethora of modeling amplifier and speaker cabinet combinations, hence tones, effectively replacing a roomful of amps, cabs and microphones. Programming the virtual amplifier is the same as tweaking the knobs on the real thing, and the same is true for programming software dynamics and effects processors in relation to their hardware equivalents. As the realism and sophistication of modeling technology continue to develop, so does the viability of virtual re-amping as a production technique. Measure the height of the strings at the twelfth fret. For most playing styles, the height between the bottom of the low "E" string and the top of the twelfth fret should be a hair over 2/32". The High "E" string should be set at 2/32". The other strings should gradually flow between these measurements. This is where I would start, but the player's style (particularly their right-hand attack), as well as string gauge, scale length and individual neck nuances may necessitate deviation from these numbers. I borrowed the above quote from an article on effects pedals by Robert Keeley (a maker of seriously fine effects pedals) which can help you remember the order to place your pedals. I have a few slight modifications and additions to this that I use, but this is a great way to remember the rough order quickly, and it comes from one of the great pedal masters. vintage harmony h75 hollow body guitar ser 519 1966, vintage 1950s vega odell model e130 hollow body electric guitar in case, vintage 1960s harmony h56 rocket hollowbody w hsc, vintage baldwin electric hollow body 12 string arch top awesome sound and player, vintage egmond hollowbody electric guitar gold foil pu make offer, vintage circa 1956 gibson es175 d hollowbody electric guitar white refin p90, vintage 1966 conqueror 335 shaped hollowbody sunburst arch top hh bigsby style, vintage vantage vsh455 hollowbody electric guitar with original case no reserve, vintage rare galanti hollowbody electric guitar super funky 1960s, vintage 1968 gibson usa johnny smith hollowbody guitar rare doublepickupwohsc, vintage 60s japan mij teisco del rey ep10t thinline hollowbody sharkfin guitar, 1966 harmony h74 hollowbody electric guitar original case clean vintage, vintage kapa series 500 hollowbody electric guitar amp; case usa, vintage bruno conqueror made in japan mij electric guitar hollow body , 1980 ibanez artist as200 vintage hollow body electric guitar, 1967 gibson usa es33512 vintage semihollowbody 12string electric guitar, vintage 1970 gibson es175d hollow body electric guitar, vintage hollowbody electric guitar harmony kay silvertone must see no reserve, 1964 gretsch tennessean 6119 vintage hollowbody electric guitar w bigsby , vintage experienced 1967 harmony h72 hollow body guitar, vintage circa 1967 framus atlantic 5113 semihollow body original cherry red , vintage original circa 1969 aria es335 copy semihollow body electric guitar, vintage 1966 baldwin burns vibraslim semihollow body guitar clean no reserve, awesome vintage hagstrom viking super rare 12 string hollow body w low action, beautiful vintage harmony h75 hollowbody electric guitar, vintage 1960s harmony silvertone model 1429l hollowbody electric guitar w ossc, vintage 1967 gretsch rally hollow body electric guitar bamboo yellow orig case, vintage 1961 epiphone broadway arch top hollow body electric guitar natural , vtg conrad brown sunburst electric guitar es 335 type hollow body wcase j0330, vintage 1970s ibanez model 2358 semihollowbody electric guitar al caiola copy, vintage 1988 gibson es335 jc showcase edition electric hollowbody guitar w case, rare vintage 60s egmond electric hollow body guitar from holland cool, vintage circa 1969 harmony rebel semihollowbody electric guitar sunburst ossc, vintage 1960s vox super lynx hollowbody electric guitar sounds amazing, vintage usa 1972 harmony rebel h81 hollowbody electric guitar near mint wtags, vintage 1954 gretsch 6186 clipper hollywood hollow body w case rare nice, vintage circa 1969 greco hollowbody double pickup electric guitar brown w ssc, vintage circa 1966 made in japan semihollow body electric guitar sunbust clean, 1967 vintage guitar aria diamond 1202t hollow body no case free shipping used, vintage 1966 harmony h59 rocket 3 hollow body red burst finish rare nice One of the most important things when choosing your guitar is of course the sound - read the study on electric guitar sounds. It’s best if you’re able to try different guitars out in a music shop, and the staff there will most likely be happy to present you with different options that are good for beginners. There you will also have the chance to see how the different guitars feel to play, and have the opportunity to ask the staff if you have any questions or need any advice. Mark Tremonti is well-known as an avid gearhead and first impressions of the MT 15 are of a purposeful, working player’s tool with no unnecessary bells or whistles. The MT 15 has clean and lead footswitchable preamp channels, with gain and master volume on the lead channel, and volume on the clean channel. Both channels have their own bass, mid and treble controls with a master presence control and a pull boost on the clean channel to add a mild overdriven edge. Around the back things are kept simple with a series effects loop plus a half-power switch which drops the MT 15 from 15 watts RMS down to around seven watts. At first glance there’s no channel indicator, however, when powered up all the MT 15’s valves are lit by LEDs which change colour: red for lead, blue for clean – very visible and very cool. The lead channel has no less than five gain stages and the amount of gain and distortion on tap is huge. However, it’s also been carefully sculpted into a stunning barrage of harmonic filth that flatters every note and power chord. Often, very high gain can easily descend into an unpleasant mush that’s perceived more as noise than music, yet the MT 15 manages to avoid this and retains exceptional clarity and articulation. The clean channel offers plenty of headroom to cater for any guitar, while pulling the channel mid-boost function adds a sweet vintage Fender overdrive with a medium-fast response that’s great for country picking or blues. SOLD OUT: ASK we may have another in stock Here we have a wonderful example of the Alvarez answer to the classic Martin 000-18 now famously linked to the Eric Clapton version from Martin om guitar today. Imported to the US by Saint Lewis Music 36 years ago. This fine example of the Alvarez 5014 is in excellent vintage condition you will not believe that she is over 36 years old when you see this in person you will realize it has been amazingly well cared for these past 3.6 decades. Its fit and finish is excellent as is its play action / neck angle ... this guitar is a pleasure to play and is truly EASY on the eyes... The neck is 1-11/16" at the nut and very comfortable to play with very little visible play wear to fingerboard or frets one will notice that this example is WELL above average condition for this age of guitar its really rare to see. Its beautiful SITKA SPRUCE top is solid and the back and sides are excellent grade Mahogany as is the neck please refer to the pics ... with nice details like its herringbone rosette, celluloid tortis pick guard, exotic Brazilian Coral Rosewood headstock overlay this guitar is more fancy than the other 5014's we have had and is in near mint vintage condition. The woods are well aged and the tone and volume has nicely opened up and aged like fine wine it takes time... a lot of guitar for this kind of price. Crafted in Japan over 36 years ago and kept in Amazing condition all these years just for you... Nicely set up with a NEW Martin Bone Nut & compensated bone saddle here at JVGUITARS. get this gem before she's gone! questions let me know... jvguitars@gmail.com . If your instrument receives regular maintenance, then you are likely to avoid any unneeded guitar setup cost. A properly cared for guitar will be regularly cleaned, oiled, and treated gently at all times. Of course, this is not possible for all people, as their preferred style of music may negate the ability to treat a guitar gently (metal and punk are good examples). Having the guitar setup can be thought of as maintenance in itself, as it is an invariable need in environments that have inconsistent weather patterns (which would be virtually all of them). The cost of a guitar setup can be insignificant if you maintain it on a regular basis. T3 (2009) – The T3 shares the same body styling as the T5 with some electronic and structural differences. It is a semi-hollow-body because it has a solid center block in the body. It comes standard with a quilted maple laminated top, and has and electric style bridge. The electronics include multiple humbucker pickups, coil splitters, and push-pull tone and volume pots. The T3 is available with the optional Bigsby vibrato in the T3/B. Since National had applied for a patent on the single cone (US patent #1,808,756), Dopyera had to develop an alternative design. He did this by inverting the cone so that, rather than having the strings rest on the apex of the cone as the National method did, they rested on a cast aluminum spider that had eight legs sitting on the perimeter of the downward-pointing cone (US patent #1,896,484). Let me begin by saying this guitar is really good right out of the box. It has a booming sound, and really fills a room even when not plugged in. However, to make it really shine, you should perform a basic setup. I replaced the saddle and pins with bone and sanded the bone saddle down to lower the action. The nut is good from the factory. I also oiled the rosewood fretboard and added Martin phosphor bronze medium strings. After doing this work, the guitar sounds every bit as good as my 90’s Martin DR which is stellar. At this price range, I didn’t expect much, but what I received was a very pleasant surprise. Don’t hesitate to buy this package! Known for their distinctive jangle and chime, Rickenbacker guitars tended to be favoured by Jangle Pop, Power pop and British Invasion-style groups – bands such as The Who, The Byrds and The Beatles. The early Rickenbackers that made this sound famous were equipped with lower-output “Toaster” pickups. These pickups were phased out circa 1969-70 for newer “Hi-Gain” pickups, which had twice the output of their illustrious predecessors. This change was almost certainly due to the trend toward the louder “Rock” sounds of the 1970s, despite the earlier models being credited by Pete Townshend as being key to the development of “the Marshall sound” and his refinement of electric guitar feedback techniques[8] Randall deserves to be up here in this list. Don't get me wrong, they've got a lot to contend with, in Orange and Mesa Boogie in particular, but Randall have always crafted excellent amps. Rugged build and vast tonal opportunities make this brand a mighty force, I mean they were good enough for Dimebag Darrell and countless others, enough said really... Jump up ^ Wright, Michael. "Jack Westheimer — Pioneer of Global Guitarmaking". Vintage Gutiar (July 1999). In August ’69, the Valco/Kay assets were auctioned off and W.M.I. purchased the rights to the Kay brand name. W.M.I. began to slowly transition Teisco del Rey guitars to the Kay brand name, which gave them greater credibility with dealers. This change was completed by around ’73 and the Teisco del Rey name then disappeared. This explains why you will occasionally see a Teisco guitar with a Kay logo. EQ placement is similar. Some players prefer to mold and shape their guitar’s primary tonal character before it is processed by other effects, but others prefer to adjust the EQ of the finished sound (again, placement in front of delay and reverb is preferable). Or maybe your distortion pedal’s EQ controls just don’t have enough bass or treble and you need to tweak its tone a touch more. If you own an EQ pedal, have fun and try placing it in different locations to see what works best for you. There’s another wrinkle: vintage-style pickup magnets can weaken over time, resulting in a softer, smoother tone. Some pickups are designed to mimic this ageing process. Say you were looking for a vintage P.A.F.-style humbucker: You could choose between one of our models that that sounds like a pickup straight off the late-’50s production line (the Seth Lover humbucker), and another that mimics a similar pickup as it would sound and look today after decades of wear and tear (the Antiquity humbucker). Guitar has a vicious tone, nice wood, great p[ickups. However the guitar I received has a problem with the volume control acting as a tone knob and also cuts out sometimes. The guitar chord had to be replaced because it was cheap and cut out like a bad phone chord. I have to take it in to a local guitar shop and have the volume control fixed. Not too expensive but some additional cost. I didn't want to send it back as I otherwise love the guitar and didn't want them to send me a different one rather than just repairing it. Plus I don't want to wait that long. But certainly a great guitar for the money. No question. A lot of amateur guitar players are tempted by the ‘cut’ of a high treble sound that gives their notes definition above the cacophony of the rest of the band. They become so accustomed to this sound that they lose sensitivity to its harshness. Treble becomes the ultimate weapon in their arsenal for the volume war, but to the listener, all they hear is a headache, aka bad tone. If you see a "\n/," where n = some number, perform a tremolo bar dip. Quickly hit and release the bar to dip the note's pitch. The number between the slashes gives an indication of the pitch you should dip to - dip the pitch by "n" semitones (a semitone is the same as the pitch between two adjacent frets.)[1] For instance, "\5/" means to drop the pitch by 5 semitones, which will be the same tone as 5 frets below the original note. While Dave Matthews Band has no more confirmed dates on their schedule, Matthews and guitarist Tim Reynolds have a number of duo performances on the docket, including a slot at Farm Aid 2018 in Hartford, CT on September 22nd alongside Willie Nelson, Neil Young, John Mellencamp, Chris Stapleton, Sturgill Simpson, Kacey Musgraves, Margo Price, Nathaniel Rateliff & The Night Sweats, Lukas Nelson & Promise of the Real, and Particle Kid. Dave and Tim also just announced their return to Mexico for a concert destination event set to take place February 15th–17th, 2019. This is one of several Squier models available that offer a pretty good product for a reasonably low price. The pickups and hardware are sometimes suspect, and the workmanship varies from instrument to instrument, but for the price, these are a very good beginner guitar choice. Squier Fat Strats are similar in appearance to the much more expensive Fender Stratocasters, so the look of the instrument is appealing. ###### Imagine a rich, authentic acoustic guitar tone coming from your electric guitar - at the flick of the switch! Replace your current saddles with Graph Tech's ghost modular pickups and one of our Acousti-Phonic preamp and you'll have instant access to true, acoustic tone from your electric guitar or bass, without altering your electric pickups. With the ghost Acousti-Phonic system you can play one guitar! It can be electric AND acoustic, separately, or blended together for an infinite range of new and exciting sounds. Almost all big guitar makers have their affordable entry level guitar models and product lines. Guitar for beginners is a market that none want to ignore. The famous acoustic guitar makers in Northern America like Martin, Taylor and Seagull provide high quality acoustic guitars for professionals and experienced guitarists. They build their brand image among the guitarists by making great sounding and great craftsmanship guitar. This truly is a pleasure writing about the best kept secret in the guitar world. The G&L Legacy Tribute. I own a USA Hamer Gold Top Archtop Standard with P-90's and it's stupendous guitar. But like all Les Pauls and high quality Mahoganies, it has a growl suited for certain kinds of Rock N Roll. However, there is another voice in my guitar arsenal and I only have one other. The G&L Legacy Tribute. This guitar can cover the other half. I bought this used for$299 and four years later I still can't put it down. So I have a $2600 guitar and a$299 guitar and love them equally. What does that tell you about the Legacy Tribute?
Alternatively – and often most effectively – you can fix phase issues in the digital realm. Record your two-mic signal on two separate tracks, then zoom in on the sound waves in each of the two channels in your DAW’s editing window until they are huge and you’re seeing the full up-and-down crests and troughs of the waves. Now, drag or nudge the sound wave of the ambient mic forward (i.e., to the left of the screen) a few milliseconds at a time until the sound waves line up perfectly. Listen again, and you should hear a very different blend that is fuller, richer, and more “together.”

#### Gretsch: Here’s another company that has been making instruments for over 100 years. Of German descent, Gretsch was established in Brooklyn in 1883 by Friedrich Gretsch. The company didn’t start making guitars until the early 1950’s when electric guitars actually became popular. With origins on banjos and mandolins, Gretsch has always been big in the country market. The endorsement by Chet Atkins has helped further cement this. Another very popular endorsee, Brian Setzer, has helped Gretsch hollowbody guitars earn a rightful place in guitar history. Like Gibson and Fender, they also produce basses, acoustics and amplifiers. Furthermore, Gretsch has a hugely successful line of drums. In 2003, Grestch set up an agreement with Fender essentially handing over the control of manufacturing and distribution. Most Grestch’s tend to be up in the pricier range. For more affordable Gretschs, look into the Electromatic series.

i'll be 50 yrs old in a few days. i started playing guitar at 8. this is my 30th guitar. i started ordering various guitars from amazon a year and a half ago and have not been displeased at all with any of my orders. i get some for young people who cannot afford to get one for themselves and so have started exploring the guitars in the price range of 80 to 140 dollars. at first glance, it would seem pretty much impossible for any guitars in this price range to be of any worth, but the factories are set up to put out fine instruments now in this price range. i can't recommend this guitar highly enough to convince you what i think of it but i am astounded at the quality, playability and sound of this guitar. it has really good tuners and rings out like a
Originally the Stratocaster was offered in a 2-color sunburst finish on a solid, deeply contoured ash body, a 21-fret one-piece maple neck with black dot inlays and Kluson tuning heads. In 1956 Fender began issuing solid Stratocasters with alder bodies.[4] In 1960 the available custom colors were standardized, many of which were automobile lacquer colors from DuPont available at an additional 5% cost. The unique single-ply, 8-screw hole white pickguard held all electronic components except the recessed jack plate—facilitating easy assembly. Despite many subsequent Stratocaster models (including copies and the Superstrat), vintage Fender models are highly valued by collectors for their investment potential and players who prefer the timbre of older models.

Recent amplifiers may include digital technology similar to effects pedals, up to the ability to model or emulate a variety of classic amplifiers. Some modeling systems also emulate the tonal characteristics of different speaker configurations, cabinets, and microphones. Nearly all amp and speaker cabinet modeling is done digitally, using computer techniques (e.g., Digital Signal Processing or DSP circuitry and software).